Panasonic of North America 9TGCF-194 Personal Computer Model CF-19 Family User Manual CF 19CTQZZBM indb

Panasonic Corporation of North America Personal Computer Model CF-19 Family CF 19CTQZZBM indb

UserManual.wiki >

Panasonic of North America >

9TGCF-194 User Manual >

User Manual for CF19

ContentsGetting StartedOPERATING INSTRUCTIONSPersonal ComputerModel No. CF-19 seriesIntroduction ................................................................. 2Read Me First ............................................................. 3Description of Parts ..................................................10First-time Operation ..................................................13Useful InformationOn-screen Manual ....................................................16Handling and Maintenance .......................................17Hard Disk Backup Function (Recover Pro) ..............19Hard Disk Data Erase Utility .....................................21Reinstalling Software ................................................22TroubleshootingError Code/Message ................................................24Troubleshooting (Basic) ............................................25Hardware Diagnostics ..............................................29AppendixLIMITED USE LICENSE AGREEMENT ...................32Speciﬁ cations ...........................................................34LIMITED WARRANTY ..............................................36Please read these instructions carefully before using this product and save this manual for future use.For further information about the com-puter, you can refer to the on-screen manual.To access the on-screen manual Î page 16 “On-screen Manual”Getting StartedUseful InformationTroubleshootingAppendix

Read Me FirstModels for U.S.A. Federal Communications Commission Radio Fre-quency Interference Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal-lation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interfer-ence will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by oneor more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment andreceiver. Connect the equipment into an outlet on a circuit dif-ferent from that to which the receiver is connected. Consult the Panasonic Service Center or an experi-enced radio/TV technician for help. Warning To assure continued compliance, use only shielded inter-face cables when connecting to a computer or peripheral.Also, any changes or modiﬁcations not expressly ap-proved by the party responsible for compliance could voidthe user’s authority to operate this equipment.FCC RF Exposure Warning: This equipment is provided with PC Card slot that couldbe used with wireless transmitters, which will be speciﬁ-cally recommended when they become available.Other third-party wireless transmitters have not beenRF exposure evaluated for use with this computer andmay not comply with FCC RF exposure requirements.<Only for model with wireless LAN/Bluetooth> This equipment complies with FCC radiation exposurelimits set forth for an uncontrolled environment. This equipment has been approved for portable operation,and unless otherwise advised in separate supplementalinstructions for individual wireless transmitter(s), requiresminimum 1.5 cm spacing be provided between antenna(s)and all person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation. This equipment may use multiple installed transmitters,which may be capable of simultaneous transmission. This equipment is provided with external antennaconnector(s) for connection to optional Car Mounter orPort Replicator for mobile external mounted antenna(s).External antenna(s) must be professionally installed andcannot exceed recommended maximum antenna gain asdescribed in individual provided supplement instructionsfor wireless transmitters. Also, user must maintain mini-mum 20 cm spacing between external antenna(s) and allperson’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation. <Only for model with wireless LAN> This product is restricted to indoor use due to its operation inthe 5.15 to 5.25 GHz frequency range.FCC requires this product to be used indoors for the fre-quency range 5.15 to 5.25 GHz to reduce the potential forharmful interference to co-channel Mobile Satellite systems.High power radars are allocated as primary users of the 5.25to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this product.25-M-1-1 This device complies with Part 15 of the FCC Rules. Op-eration is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired op-eration. Responsible Party: Panasonic Corporation of North America One Panasonic Way Secaucus, NJ 07094 Tel No:1-800-LAPTOP5 (1-800-527-8675) 6-M-1 FCC Regulation Notice for modemThis equipment contains a FCC approved modem.1. This equipment complies with CFR47 Part 68 rules.On the computer is a label that contains, among otherinformation, the FCC registration number and ringerequivalence number (REN) for this equipment. If re-quired, this information must be provided to the tele-phone company.2. An FCC compliant telephone cord and modular plugis provided with this equipment. This equipment is designed to be connected to the telephone networkor premises wiring using a compatible modular jackwhich is Part 68 compliant. See Installation Instruc-tions for details. 3. The REN is used to determine the quantity of deviceswhich may be connected to the telephone line. Ex-cessive RENs on the telephone line may result in thedevices not ringing in response to an incoming call. Inmost, but not all area, the sum of RENs should not ex-ceed ﬁve (5.0). To be certain of the number of devices that may be connected to a line, as determined by thetotal RENs, contact the local telephone company.4. If your telephone equipment cause harm to the tele-phone network, the telephone company will notify youin advice that temporary discontinuance of servicemay be required. But if advice notice isn’t practical, thetelephone company will notify the customer as soonas possible. Also, you will be advised of your right to ﬁle a complaint with the FCC if you believe it is neces-sary.5. The telephone company may take changes in its facili-ties, equipment, operations or procedures that couldaffect the operation of the equipment. If this happens the telephone company will provide advance noticein order for you to make necessary modiﬁ cations to maintain uninterrupted service.6. If trouble is experienced with this equipment, for repairor warranty information, please contact PanasonicCorporation of North America at DIAL TOLL FREE 1-800-LAPTOP5 (1-800-527-8675). If the equipment is causing harm to the telephone network, the telephonecompany may request that you disconnect the equip-ment until the problem is resolved.7. There are no user serviceable parts contained in thisequipment.8. This equipment may not be used on coin service pro-vided by the telephone company. Connection to party lines is subject to state tariffs. Getting Started 3

4Getting StartedRead Me First9. The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the ﬁ rst page of the transmission, the date and time it is sent and an identiﬁ cation of the business or other entry, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. In order to program this information into your fax software, you should refer to the manual of the Fax software being used.10. According to the FCC’s electrical safety advisory, we recommend that you may install an AC surge arrestor in the AC outlet to which this equipment is connected. Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources and that this is a major nationwide problem. “Caution : To reduce the risk of ﬁ re, use only No.26 AWG or larger telecommunication line cord.” “ATTENTION : Pour réduire le risque d’incendie, utiliser uniquement des conducteurs de télécommunications 26 AWG ou de section supérieure.”16-M-1Notice for the products using LCDThis product uses one or more ﬂ uorescent lamps contain-ing a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org/> 24-M-1UL1604-conforming model. (The model which has de-scription of “UL1604” in the bottom of the computer.)z THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DIVISION2, GROUPS A, B, C, AND D OR NON-HAZARDOUS LOCATIONS ONLY.z WARNING-EXPLOSION HAZARD-SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION2.z When connecting and using a device manufactured by a third party, enquire to the manufacturer as to wheth-er the device suits CLASS I, DIVISION2. 33-M-1Models for CanadaIndustry Canada (IC) Notice for modemThis equipment contains an Industry Canada approved modem unit.The Industry Canada label is afﬁ xed on the modem unit.EQUIPMENT ATTACHEMENT LIMITATIONS“NOTICE: The Industry Canada label identiﬁ es certiﬁ ed equipment. This certiﬁ cation means that the equipment meets telecommunications network protective, opera-tional and safety requirements as prescribed in the ap-propriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connec-tion. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.Repairs to certiﬁ ed equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.Users should ensure for their own protection that the elec-trical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be par-ticularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection author-ity, or electrician, as appropriate.”“NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maxi-mum number of terminals allowed to be connected to a tele-phone interface. The termination on an interface may consist of any combination of devices subject only to the require-ment that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.”REN: See bottom of the computerRESTRICTIONS CONCERNANT LE RACCORDEMENT DE MATÉRIEL“AVIS: L’étiquette d’Industrie Canada identiﬁ e le matériel homologué. Cette étiquette certiﬁ e que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’entreprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de raccordement.L’abonné ne doit pas oublier qu’il est possible que la con-formité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations.Les réparations de matériel homologué doivent être coor-données par un représentant désigné par le fournisseur.L’entreprise de télécommunications peut demander à l’utilisateur de débrancher un appareil à la suite de répa-rations ou de modiﬁ cations effectuées par l’utilisateur ou à cause de mauvais fonctionnement.Pour sa propre protection, l’utilisateur doit s’assurer que tous les ﬁ ls de mise à la terre de la source d’énergie électrique, des lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales. Avertissement: L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à un service d’inspection des installations élec-triques, ou à un électricien, selon le cas.”“AVIS: L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condi-tion que la somme d’indices d’équivalence de la sonnerie de touts les dispositifs n’excède pas 5.”IES: Voir sous le fond de l’ordinateur 17-Ca-1

5Getting StartedCSA C22 2 NO.213-conforming model. (The model which has description of “CSA C22 2 NO.213” in the bottom of the computer.)z THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DIVISION2, GROUPS A, B, C, AND D OR NON-HAZARDOUS LOCATIONS ONLY.z WARNING-EXPLOSION HAZARD-SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION2.z When connecting and using a device manufactured by a third party, enquire to the manufacturer as to wheth-er the device suits CLASS I, DIVISION2. 33-Ca-1<Only for model with wireless LAN/Bluetooth>Industry CanadaThis product complies with RSS210 Industry Canada.Operation is subject to the following two conditions;(1) this device may not cause interference, and(2) this device must accept any interference, including inter-ference that may cause undesired operation of the device.30-Ca-1-1<Only for model with wireless LAN>This product (local network devices) for the band 5150-5250 MHz is only indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems.High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LELAN devices.30-Ca-2-1This device has been designed to operate with an anten-na having a maximum gain of 2.15 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The Required antenna impedance is 50 ohms.To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. 25-Ca-1-1<Only for model with Bluetooth>This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. 7-M-1Models for Europe<Only for model with a “CE” mark on the bottom of the computer>Declaration of Conformity (DoC)“Hereby, we declare that this Personal Computer is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC.”Hint:If you want to get a copy of the original DoC of our products which relates to the R&TTE, please con-tact our web address: http://www.doc.panasonic.deContact:Panasonic Services EuropeA Division of Panasonic Marketing Europe GmbHPanasonic Testing CentreNetwork connection.The terminal equipment is intended for connection to the following public network;In all the countries of European Economical Area;- Public Switched Telephony NetworksTechnical Features.The terminal equipment includes the following features;- DTMF dialing- Maximum bitrate receiving mode: 56 kbit/s- Maximum bitrate sending mode: 33.6 kbit/sThis product is designed to interwork with the Public Switched Telecommunication Networks in UK, Ireland, Nether-lands, Sweden, Denmark, Finland, Switzerland, Luxembourg, Belgium, France, Germany, Spain, Portugal, Iceland, Greece, Italy, Norway and Austria. 18-E-1Compliance Notice - CE MarkThis equipment is in conformance with the requirements of the European Council Directive listed below:73/23/EEC Low Voltage Directive with amendment 93/68/EEC89/336/EEC EMC Directive with amendments 92/31/EEC and 93/68/EEC1999/5/EC R&TTE21-E-1

Read Me FirstImportant Safety Instructions / Importantes Mesures De Sécurité Getting Started When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of ﬁre, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3. Do not use the telephone to report a gas leak in the vicinity of the leak. 4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a ﬁ re. They may explode. Check with local codes for possible special disposal instructions. SAVE THESE INSTRUCTIONS 19-E-1 Certaines mesures de sécurité doivent être prises pen-dant l’utilisation de matérial téléphonique aﬁn de réduire les risques d’incendie, de choc électrique et de blessures. En voici quelquesunes: 1. Ne pas utiliser l’appareil près de l’eau, p.ex., près d’ une baignoire, d’un lavabo, d’un évier de cuisine, d’un bac à laver, dans un sous-sol humide ou près d’une piscine.2. Éviter d’utiliser le téléphone (sauf s’il s’agit d’un ap-pareil sans ﬁl) pendant un orage électrique. Ceci peut présenter un risque de choc électrique causé par la foudre. 3. Ne pas utiliser l’appareil téléphonique pour signaler une fuite de gaz s’il est situé près de la fuite. 4. Utiliser seulement le cordon d’alimentation et le type de piles indiqués dans ce manual. Ne pas jeter les piles dans le feu: elles peuvent exploser. Se conform-er aux règlements pertinents quant à l’élimination des piles. CONSERVER CES INSTRUCTIONS Information to the User <Only for model with wireless LAN/Bluetooth> This product and your Health This product, like other radio devices, emits radio fre-quency electromagnetic energy. The level of energy emitted by this product however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones. Because this product operates within the guidelines found in radio frequency safety standards and recommenda-tions, we believe this product is safe for use by consum-ers. These standards and recommendations reﬂ ect the consensus of the scientiﬁc community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of this prod-uct may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include: Using this product on board of airplanes, or In any other environment where the risk of interference to other devices or services is perceived or identiﬁed as harmful. If you are uncertain of the policy that applies on the use of wireless devices in a speciﬁc organization or environ-ment (e.g. airports), you are encouraged to ask for autho-rization to use this product prior to turning on the product. Regulatory Information We are not responsible for any radio or television interfer-ence caused by unauthorized modiﬁcation of this product. The correction of interference caused by such unauthor-ized modiﬁcation will be the responsibility of the user. We and its authorized resellers or distributors are not liable for damage or violation of government regulations that may arise from failing to comply with these guidelines. 26-M-1 Lithium Battery / Pile au lithium Lithium Battery! This computer contains a lithium battery to enable the date, time, and other data to be stored. The battery should only be exchanged by authorized service person-nel. Warning! A risk of explosion from incorrect installation or misappli-cation may possibly occur. 15-E-1 Pile au lithium! Le micro-ordinateur renferme une pile au lithium qui permet de sauvegarder certaines données, notamment la date et l’heure. La pile ne doit être remplacée que par un technicien qualiﬁé. Danger ! Risque d’explosion en cas de non respect de cette mise en garde! 6 19-F-1 15-F-1

Precautions THIS PRODUCT IS NOT INTENDED FOR USE AS, OR AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS, AIR TRAF-FIC CONTROL EQUIPMENT/SYSTEMS, OR AIRCRAFTCOCKPIT EQUIPMENT/SYSTEMS*1. PANASONIC WILL NOT BE RESPONSIBLE FOR ANY LIABILITY RESULT-ING FROM THE USE OF THIS PRODUCT ARISING OUT OF THE FOREGOING USES. *1 AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include Class2 Electrical Flight Bag (EFB) Systems and Class1 EFB Systems when used during critical phases of ﬂight (e.g., during take-off and landing) and/or mounted on to the aircraft. Class1 EFB Systems and 2 EFB Systems are deﬁned by FAA: AC (Advisory Circular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaﬂ ets) No.36. Panasonic cannot guarantee any speciﬁ cations, technolo-gies, reliability, safety (e.g. Flammability/Smoke/Toxic-ity/Radio Frequency Emission, etc) requirements relatedto aviation standards that exceed the speciﬁcations of our COTS (Commercial-Off-The-Shelf) products. 39-E-1 This computer is not intended for use in medical equipmentincluding life-support systems, air trafﬁc control systems, orother equipment, devices or systems that are involved withensuring human life or safety. Panasonic cannot be held responsible in any way for any damages or loss resultingfrom the use of this computer in these types of equipment,devices or systems, etc.The CF-19 was developed based on thorough research intothe real-world portable computing environments. Exhaustivepursuit of usability and reliability under harsh conditions ledto innovations such has the magnesium alloy exterior, vibra-tion damped hard disk drive and ﬂoppy disk drive, ﬂexible internal connections. The CF-19’s outstanding engineering has been tested using the strict MIL-STD- 810F (for vibrationand shock) and IP (for dust and water) based procedures.As with any portable computer device precautions should betaken to avoid any damage. The following usage and han-dling procedures are recommended. Before putting the computer away, be sure to wipe off any moisture. If a Malfunction Occurs, Immediately Unplug the AC Cord and the Battery Pack Computer is damaged Foreign object inside computer  Smoke emitted Unusual smell emitted  Unusually hotContinuing to use the computer while any of the above con-ditions are present may result in ﬁre or electric shock. If a malfunction occurs, immediately turn the power off and unplug the AC cord, and then remove the battery pack. Do Not Touch the Computer and Cable When It Starts ThunderingElectric shock may result. Do Not Connect the AC Adaptor to a Power Source Other Than a Standard Household AC Outlet Otherwise, a ﬁre due to overheating may result. Connectingto a DC/AC converter (inverter) may damage the AC adap-tor. On an airplane, only connect the AC adaptor/charger to an AC outlet speciﬁcally approved for such use. Do Not Do Anything That May Damage the AC Cord, the DC Plug, or the AC AdaptorDo not damage or modify the cord, place it near hot tools,bend, twist, or pull it forcefully, place heavy objects on it, or bundle it tightly.Continuing to use a damaged cord may result in ﬁ re, short circuit, or electric shock.Do Not Pull or Insert the DC Plug If Your Hands Are WetElectric shock may result. Clean the DC Plug of Dust and Other Debris RegularlyIf dust or other debris accumulates on the plug, humidity, etc. may cause a defect in the insulation, which may result in a ﬁre.Pull the plug, and wipe it with a dry cloth.Pull the plug if the computer is not being used for a longperiod of time. Insert the AC Plug CompletelyIf the plug is not inserted completely, ﬁre due to overheatingor electric shock may result.Do not use a damaged plug or loose AC outlet.Close the Connector Cover Tightly When Using the Computer Where Is a Lot of Water, Moisture, Steam, Dust, Oily Vapors, etc.The entry of foreign matter may cause a ﬁre or electric shocks. If foreign matter has found its way inside, immediately turnthe power off and unplug the AC cord, and then remove the battery pack. Then contact your technical support of-ﬁce. Do Not Disassemble the ComputerThere are high-voltage areas inside which may give you anelectric shock if you should touch them. Do not touch the pins and circuit boards inside, and do not allow foreign mat-ter to enter inside. Also, remodeling or disassembly may cause a ﬁre. Keep SD Memory Cards Away from Infants and Small Children Accidental swallowing will result in bodily injury.In the event of accidental swallowing, see a doctor immedi-ately.Do Not Place the Computer on Unstable SurfacesIf balance is lost, the computer may fall over or drop, result-ing in an injury. Avoid StackingIf balance is lost, the computer may fall over or drop, result-ing in an injury. Do Not Leave the Computer in High Temperature Envi-ronment Such as in a Sun-Heated Car, for a Long Period of Time Leaving the computer where it will be exposed to extremelyhigh temperatures such as in a sun-heated car or in directsunlight may deform the cabinet and/or cause trouble in theinternal parts. Continued use in such a resulting conditionmay lead to short-circuiting or insulation defects, etc. whichmay in turn lead to a ﬁre or electric shocks. Hold the Plug When Unplugging the AC CordPulling on the cord may damage the cord, resulting in a ﬁre or electric shock. Do Not Move the Computer While the DC Plug Is Con-nected The AC cord may be damaged, resulting in ﬁre or electric shock. If the AC cord is damaged, unplug the DC plug immedi-ately. Use Only the Speciﬁed AC Adaptor With Your ComputerUsing an AC adaptor other than the one supplied (attached to your computer or supplied by Panasonic) may result in aﬁre. Do Not Subject the AC Adaptor to Any Strong ImpactUsing the AC adaptor after a strong impact such as being dropped may result in electric shock, short circuit, or ﬁre. Take a Break of 10-15 Minutes Every HourUsing the computer for long periods of time may have detri-mental health effects on the eyes or hands. Getting Started 7

8Getting StartedRead Me FirstDo Not Turn the Volume Up to Loud When Using Head-phonesListening at high volumes that overstimulate the ear for long periods of time may result in loss of hearing.Use the Modem with a Regular Telephone LineConnection to an internal phone line (on-premise switches) of a company or business ofﬁ ce, etc. or to a digital public phone or use in a country or area not supported by the com-puter may result in a ﬁ re or electric shocks.Do Not Connect a Telephone Line, or a Network Cable Other Than the One Speciﬁ ed, into the LAN PortIf the LAN port is connected to a network such as the ones listed below, a ﬁ re or electric shock may result.y Networks other than 1000BASE-TX, 100BASE-TX or 10BASE-Ty Phone lines (Telephone lines, internal phone lines (on-premise switches), digital public phones, etc.)Precautions (Battery Pack)Do Not Use with Any Other ComputerThe battery pack is rechargeable and was intended for the speciﬁ ed computer or charger. If it is used with a computer other than the one for which it was designed, electrolyte leakage, generation of heat, ignition or rupture may result.Do Not Charge the Battery Using the Methods Other Than Indicated in This ManualIf the battery pack is not charged using one of the methods indicated in this manual, electrolyte leakage, generation of heat, ignition or rupture may result.Do Not Throw the Battery Pack into a Fire or Expose It to Excessive HeatGeneration of heat, ignition or rupture may result.Avoid Extreme Heat (Near the Fire, in Direct Sunlight, for Example)Electrolyte leakage, generation of heat, ignition or rupture may result.Do Not Insert Sharp Objects into the Battery Pack, Ex-pose It to Bumps or Shocks, Disassemble, or Modify ItElectrolyte leakage, generation of heat, ignition or rupture may result.Do Not Short the Positive (+) and Negative (-) ContactsGeneration of heat, ignition or rupture may result. Do not place the battery pack together with articles such as neck-laces or hairpins when carrying or storing.Do Not Use This Computer with a Battery Pack Other Than the One Speciﬁ edUse only the speciﬁ ed battery pack (CF-VZSU48U) with your CF-19. Use of battery packs other than those manufactured and supplied by Panasonic may present a safety hazard (generation of heat, ignition or rupture).z Do not touch the terminals on the battery pack. The bat-tery pack may no longer function properly if the contacts are dirty or damaged.z Do not expose the battery pack to water, or allow it to become wet.z If the battery pack will not be used for a long period of time (a month or more), charge or discharge (use) the battery pack until the remaining battery level becomes 30% to 40% and store it in a cool, dry place.z This computer prevents overcharging of the battery by recharging only when the remaining power is less than approx. 95% of capacity.Do Not Use with Exposing the Skin to the Computer for a Long Period of TimeUsing the computer with exposing the skin to the heat source of the computer or AC adaptor for a long period of time can cause a low-temperature burn.z Do not place the computer near a television or radio re-ceiver.z Keep the computer away from magnets. Data stored on the hard disk may be lost.z The battery pack is not charged when the computer is ﬁ rst purchased. Be sure to charge it before using it for the ﬁ rst time. When the AC adaptor is connected to the computer, charging begins automatically.z Should the battery leak and the ﬂ uid get into your eyes, do not rub your eyes. Immediately ﬂ ush your eyes with clear water and see a doctor for medical treatment as soon as possible. NOTE z The battery pack may become warm during recharg-ing or normal use. This is completely normal.z Recharging will not commence if internal temperature of the battery pack is outside of the allowable temper-ature range (0 °C to 50 °C {32°F to 122 °F}). (Î Reference Manual “Battery Power”) Once the allowable range requirement is satisﬁ ed, charging begins automatically. Note that the recharging time varies based on the usage conditions. (Recharging takes longer than usual when the temperature is 10 °C {50 °F} or below.)z If the temperature is low, the operating time is short-ened. Only use the computer within the allowable temperature range.z This computer has a high temperature mode function that prevents the degradation of the battery in high temperature environments. (Î Reference Manual “Battery Power”) A level corresponding to a 100% charge for high temperature mode is approximately equivalent to an 80% charge level for normal tempera-ture mode.z The battery pack is a consumable item. If the amount of time the computer can be run by using a particular battery pack becomes dramatically shorter and re-peated recharging does not restore its performance, the battery pack should be replaced with a new one.z When transporting a spare battery inside a package, briefcase, etc., it is recommended that it be placed in a plastic bag so that its contacts are protected.z Always power off the computer when it is not in use. Leaving the computer on when the AC adaptor is not connected will exhaust the remaining battery capacity.

For Used in Motor Vehicle /Pour L’utilisation Dans Un Véhicule Motorisé Warning: Notebook Computer may be installed in a mo-tor vehicle and visible to the driver only if used to support vehicle related functions such as vehicle information, system control, rear or side observation and navigation. If used for entertainment purpose, such as television recep-tion or video play, it must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. Check with individual state/provincial laws to de-termine lawful use of this product while operating within a motor vehicle. Avertissement : L’ordinateur bloc-notes peut être installé dans un véhicule motorisé et dans le champ de vision du conducteur uniquement en tant que dispositif d’aide aux fonctions du véhicule, comme par exemple pour fournir des informations sur le véhicule, comme dispositif de contrôle de système, pour l’observation à l’arrière ou sur les côtés du véhicule, ainsi que pour fournir de l’informa-tion routière. Pour toute utilisation à ﬁn de divertissement, comme par exemple pour regarder la télévision ou jouer à des jeux vidéo, il doit être installé à l’arrière du siège du conducteur, en un emplacement où il ne sera pas visible, ni directement ni indirectement, pour le conducteur du véhicule motorisé. Vériﬁez les lois fédérales et nationales qui régissent l’utilisation légale de cet appareil à l’intérieur d’un véhicule motorisé. 35-M-1 Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) Getting Started Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union.If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.36-M-1 9

Getting Started Description of PartsA: Wireless LAN Antenna <Only for model with wireless LAN>Reference Manual “Wireless LAN”B: Bluetooth Antenna <Only for model with Bluetooth>Reference Manual “Bluetooth”C: Stylus/Pen Holder D: Touch Pad E: LED Indicator : Wireless ready This indicator lights when Wireless LAN, Blue-tooth, and/or Wireless WAN are connected and ready. It does not necessarily indicate the On/Off condition of the wireless connection. Reference Manual “Wireless Switch Utility” : Wireless WAN status <Only for model with wireless WAN>  Refer to the instruction manual of the wireless device. : Caps lock : Numeric key (NumLk) : Scroll lock (ScrLk) : Hard disk drive statusF: Tablet Buttons Reference Manual “Tablet Buttons” G: LCD <Only for model with touchscreen>Reference Manual “Touchscreen”<Only for model with digitizer>Reference Manual “Digitizer”H: Display Release Latch  page 12 “Switching to the Tablet mode” I: Speaker Reference Manual “Key Combinations” J: Function Key Reference Manual “Key Combinations” K: Keyboard L: Hard Disk Drive Reference Manual “Hard Disk Drive” M: Battery Pack N: Power Switch O: LED Indicator : Battery status Reference Manual “Battery Power” : Power status (Off: Power off/Hibernation, Green: Power on, Blinking green: Standby) A lithium ion battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery. L’appareil que vous vous êtes procuré est alimenté par une batterie au lithium-ion. Pour des renseignements sur le recyclage de la batterie, veuillez composer le 1-800-8-BATTERY. 10

11Getting StartedLeft sideRear side BottomA: DC-IN JackB: USB PortÎ Reference Manual “USB Devices”C: IEEE 1394 Interface ConnectorÎ Reference Manual “IEEE 1394 Devices”D: Modem PortÎ Reference Manual “Modem”E: LAN PortÎ Reference Manual “LAN”F: SD Memory Card Indicator(Blinking: During access)Î Reference Manual “SD Memory Card”G: SD Memory Card SlotÎ Reference Manual “SD Memory Card”H: Wireless SwitchÎ Reference Manual “Wireless Switch Utility”I: PC Card Slot Î Reference Manual “PC Card / ExpressCard”J: ExpressCard SlotÎ Reference Manual “PC Card / ExpressCard”K: Headphone Jack You can connect headphones or ampliﬁ ed speakers. When they are connected, audio from the internal speakers is not heard.L: Microphone Jack A condenser microphone can be used. If other types of microphones are used, audio input may not be pos-sible, or malfunctions may occur as a result.y When recording in stereo using a stereo micro-phone:Double-click in the notiﬁ cation area, click [Op-tions] - [Properties], and add a check mark for [Re-cording], click [OK] - [Options] - [Advanced Controls] - [Advanced], remove a check mark for [Mono Micro-phone], and then click [Close].y When using a monaural microphone with a 2-termi-nal plug:With the settings outlined above, only audio on the left track will be recorded.When monitoring the microphone audio using head-phones, sounds on the left track cannot be heard, regardless of the above settings. This is a result of the computer’s speciﬁ cations, and is not a malfunction.M: Security Lock A Kensington cable can be connected. For further information, read the manual that comes with the cable.N: External Display PortÎ Reference Manual “External Display”O: Serial PortP: RAM Module SlotÎ Reference Manual “RAM Module”Q: Expansion Bus ConnectorÎ Reference Manual “Port Replicator / Car Mounter”R: External Antenna Connector

12Getting StartedDescription of PartsSwitching to the Tablet modeA Lift up the display so it stands perpendicular to the body.B Slide and hold the display release latch (A), and rotate the display clockwise until it clicks.Attaching the stylus to the computerUse the tether to attach the stylus to the computer so you will not lose it. There are holes (A) to attach it.y For model with digitizer, the tether and pen are already attached to the computer at purchase.Attaching the hand strap and the shoulder strapAttach the hand strap to any two of the corners (A) using the screws.You can connect the shoulder strap (B) to the hand strap.(The illustration is an example.) CAUTION z Do not use the strap to carry a heavier weight than the computer. Other-wise the strap may become loose by itself.z Do not use the strap if it becomes worn or damaged.C Close as the display faces up and ﬁ x it using the latch (B).

13Getting Started PreparationA Check and identify the supplied accessories.If you do not ﬁ nd the described accessories, contact Panasonic Technical Support (Î page 36).• AC Adaptor . . . . . 1Model No: CF-AA1633A• AC Cord . . . . . . . 1 • Battery Pack . . . 1Model No: CF-VZSU48• Modem Telephone Cable . . . 1• Tether . . . . . . . . . 1 • Shoulder strap . . 1 • Soft Cloth . . . . . . 1<Only for model with touchscreen>• Stylus . . . . . . . . . . . . . . . . . . . 1<Only for model with digitizer>• Pen . . . . . . . . . . . . . . . . . . . . . 1• Operating Instructions (This book) . . .1• Product Recovery DVD-ROM . . . . . . . .1• Windows® Book . . . . . . . . . . . . . . . . . . .1z For model with digitizer, the tether and pen are already attached to the computer at purchase.B Read the LIMITED USE LICENSE AGREEMENT before breaking the seal on the computer’s packaging (Î page 32).1 Insert the battery pack.A Slide the latch (A) to the right to unlock the cover.B Slide the latch (A) down, and open the cover.C Insert the battery pack until it securely ﬁ ts the connector.D Close the cover until it clicks.E Slide the latch (B) to the left to lock the cover. CAUTION z Make sure the latch is securely locked. Otherwise the battery pack may fall when you carry the computer.z Do not touch the terminals of the battery pack and the computer. Doing so can make the terminals dirty or damaged, and may cause malfunction of the battery pack and the computer.First-time Operation

14Getting StartedFirst-time Operation2 Connect your computer to a power outlet. The battery charging starts automatically. CAUTION z Do not disconnect the AC adaptor and do not switch the wireless switch to on until the ﬁ rst-time operation procedure is completed.z When using the computer for the ﬁ rst time, do not connect any peripheral device except the battery pack and AC adaptor.z Handling the AC adaptory Problems such as sudden voltage drops may arise during periods of thunder and lightning. Since this could adversely affect your computer, an uninter-ruptible power source (UPS) is highly recommended unless running from the battery pack alone.3 Turn on the computer.A Pull up the part (A) and release the latch.B Lift open the display.C Slide and hold the power switch (B) for approximately one second until the power indicator lights. CAUTION z Do not slide the power switch repeatedly.z The computer will forcibly be turned off if you slide and hold the power switch for four seconds or longer.z Once you turn off the computer, wait for ten seconds or more before you turn on the computer again.z Do not perform the following operation until the hard disk drive indicator turns off.y Connecting or disconnecting the AC adaptory Sliding the power switchy Touching the keyboard, touch pad, tablet buttons, touchscreen (only for model with touchscreen), digitizer (only for model with digitizer) or external mousey Closing the displayz When the CPU temperature is high, the computer may not start up to prevent overheating of the CPU. Wait until the computer cools down, and then turn the power on again. If the computer does not power on even after cooling down, contact Panasonic Technical Support (Î page 36).4 Setup Windows.A Follow the on-screen instructions. CAUTION z When you set date/time/time zone and click [Next], the screen may not go to the next step for a few minutes. Do not touch the keyboard or touch pad, and wait until the screen changes.z If “An unexpected error has occurred…” (or a similar message) is displayed, click [OK]. This is not a malfunction.z Wait until the hard disk drive indicator has turned off.z This computer periodically records the management information including the hard disk information such as number of hours powered-on, number of times powered-on, internal temperature, replacement sector. The maximum data vol-ume for each record is 750 byte. These information are only used for estimating the cause when the hard disk goes down by any possibility. They are never sent to outside via network nor used for any other purpose except for the purpose described the above. To disable the function, add the check mark for [Disable the automatic save function for management information history] in [Hard Disk Status] of PC Infor-mation Viewer, and click [OK].

15Getting Started5 Create a new account.A Click [start] - [Control Panel] - [User Accounts] - [Create a new account]. CAUTION z Remember your password. If you forget the password, you cannot use the Windows operation system. Creating a password reset disk beforehand is recommended.6 <Only for model with touchscreen> Perform the touchscreen calibration.A Click [start] - [All Programs] - [Fujitsu Touch Panel (USB)] - [Touch Screen Calibration Utility].B Using the stylus, touch each of the 12 “+” target marks one by one until it blinks, and then click [Calibration].C Click [Save & Exit]. NOTE z Regarding Windows XP You can select the Classic view of Control Panel or the Classic Start menu. You can also change the way a user logs on or off. This manual explains using the Windows XP default setting (not Classic view or Classic Start menu etc.).z Windows Update You can update to the latest patches and service packs for Windows with the following menus. [start] - [All Programs] - [Windows Update] Do not apply “Driver Updates” even if a message to update a driver appears. If a driver update is required, contact Panasonic Technical Support (Î page 36).z If the message “Your computer might be at risk” is displayed Select on the notiﬁ cation area and make the appropriate settings. The Windows Security Center regularly gives you notice so that you can make the optimum settings. This is not an error message and you can use the computer. However, making appropriate measures is recommended to reduce the risk of virus and other attacks.z Note that the computer consumes electricity even when the computer power is off. If the battery pack is fully charged, the battery will fully discharge in Approx. 7 weeks.

16Useful InformationOn-screen ManualYou can access the Reference Manual and the Important Tips on the computer screen.When you access the Reference Manual and the Important Tips for the ﬁ rst time, the License Agreement of the Adobe Reader may be displayed. Read it carefully and select [Accept] to proceed. Reference Manual The Reference Manual contains the practical information to help you fully enjoy the computer’s performance.To access the Reference Manual:A Click [start] - [Reference Manual].Contents Key Combinations Tablet Buttons Touchscreen Digitizer Software Keyboard Panasonic Hand Writing Display Rotation Standby and Hibernation Functions Security Measures Battery Power PC Card / ExpressCard SD Memory Card SD Security RAM Module Port Replicator / Car Mounter External Display USB Devices IEEE 1394 Devices Modem LAN Wireless Switch Utility Wireless LAN Bluetooth Hard Disk Drive Setup Utility Icon Enlarger Loupe Utility DMI Viewer Recover Pro Technical Information Troubleshooting (Advanced)Some contents only apply to some limited models. Important Tips The Important Tips will provide you with the helpful information about the battery and touchscreen. Read to use the battery pack in the optimum condition to obtain longer operation time.To access the Important Tips:A Double-click on the desktop. Alternatively click [start] - [All Programs] - [Panasonic] - [On-Line Manuals] - [Important Tips].

17Useful InformationHandling and MaintenanceOperation environment Place the computer on a ﬂ at stable surface. Do not place the computer upright or turn it over. If the computer is exposed to an extremely strong impact, it may become inoperable. Temperature: Operation : 5 °C to 35 °C {41 °F to 95 °F} Storage : -20°C to 60 °C {- 4 °F to 140 °F} Humidity: Operation : 30% to 80% RH (No condensation) Storage : 30% to 90% RH (No condensation) Even within the above temperature/humidity ranges, using for a long time in an extreme environment will result in the product deterioration and will shorten the product life. Do not place the computer in the following areas, otherwise the computer may be damaged. Near electronic equipment. Image distortion or noise may occur. In extremely high or low temperature. As the computer can become hot during operation, keep it away from items that are sensitive to heat.Handling cautionsThis computer is designed to minimize shock to parts such as the LCD and the hard disk drive and equipped with a drip-proof keyboard, but no warranty is provided against any trouble caused by shock. Be extremely careful when han-dling the computer. When carrying the computer: Turn off the computer. Remove all external devices, cables, cards and other protruding things. Do not drop or hit the computer against solid objects. Do not leave the display open. Do not grip the display part. Do not put anything (e.g., a piece of paper) between the display and keyboard. When you board an airplane, take the computer with you and never put it in your checked luggage. When using the computer on airplane, follow the airline’s instructions. When carrying a spare battery, put it in a plastic bag to protect its terminals. The touch pad is designed to be used with a ﬁ nger tip. Do not place any object on its surface and do not press down strongly with sharp-pointed or hard objects that may leave marks (e.g., nails, pencils and ball point pens). Avoid any harmful substances such as oil from getting into the touch pad. The cursor may not work correctly. This computer contains a magnet and magnetic products at the locations circled in the illustration at right. Avoid leaving metallic object or magnetic media in contact with these areas. Use only the included stylus/pen to touch the screen. Do not place any object on its sur-face and do not press down strongly with sharp-pointed or hard objects that may leave marks (e.g., nails, pencils and ball point pens). Do not use the stylus/pen when dust or dirt (e.g., oil) is on the screen. Otherwise foreign particles on the screen/stylus/pen can scratch the screen surface or obstruct the stylus/pen operation. Use the stylus/pen only for touching the screen. Using it for any other purpose may damage the stylus/pen and result in scratches on the screen.<Only for model with digitizer> The digitizer uses electromagnetic induction and may not work properly near strong electrical ﬁ eld or magnetic ﬁ eld such as: near AM radio base station or relay station antennas near CRT displays that generate strong electromagnetic ﬁ eld noise Move the digitizer away from such locations so it will work properly. The cursor cannot follow the pen movement if you move the pen too quickly. When using peripheral devicesFollow these instructions and the Reference Manual to avoid any damage to the devices. Carefully read the instruction manuals of the peripheral devices. Use the peripheral devices conforming to the computer’s speciﬁ cations. Connect to the connectors in the correct direction. If it is hard to insert, do not try forcibly but check the connector’s shape, direction, alignment of pins, etc. If screws are included, fasten them securely. Remove the cables when you carry the computer. Do not pull the cables forcibly.

Handling and MaintenanceUseful Information Preventing your computer from unauthorized use via wireless LAN <Only for model with wireless LAN> Before using wireless LAN, make the appropriate security settings such as data encryption. Computrace® Software Computrace® software tracks your stolen computer.Perform the following steps before installing Computrace® software. Computrace® software is not included or installed in this computer. CAUTION You will be unable to set [Computrace (R) BIOS Module] to [Disable] once you have set to [Enable]. Do not change the setting when not used.  Even if you have set [Computrace (R) BIOS Module] to [Enable], this setting may return to [Disable] after repairs to the motherboard, etc. have been made. NOTE Consult Absolute Software Corp. before disposal. Refer to the following URL for Computrace® software for installation and available service regions. Note that this service is only available in certain regions. http://www.absolute.com 1 Turn on or restart the computer, and press F2 while [Panasonic] boot screen is dis-played. The Setup Utility starts up. If the password is requested, enter the Supervisor Password.2 Select the [Security] menu, then select [Computrace (R) Sub-Menu] and press Enter.3 Select [Computrace (R) BIOS Module], and set to [Enable].4 At the conﬁrmation message, select [Execute] and press Enter.5 At the reconﬁrmation message, select [Execute] and press Enter.6 Press F10 .At the conﬁrmation message, select [Yes] and press Enter.The computer restarts.Maintenance To clean the LCD panel Use the soft cloth included with the computer. (For further information, refer to “Suggestions About Cleaning the LCD Surface” that comes with the soft cloth.) To clean areas other than the LCD panel Wipe with a soft dry cloth such as gauze. When using detergent, dip a soft cloth in water-diluted detergent and wring it thoroughly. CAUTION Do not use benzene, thinner, or rubbing alcohol since it may adversely affect the surface causing discoloration, etc. Do not use commercially-available household cleaners and cosmetics, as they may contain components harmful to the surface. Do not apply water or detergent directly to the computer, since liquid may enter inside of the computer and cause malfunction or damage. 18

$19Useful InformationHard Disk Backup Function (Recover Pro)The Recover Pro creates a backup area (storage area) on the hard disk to back up (store) the hard disk data, and re-stores the backup data to its original location when it is lost or corrupted by operational errors or other factors. You do not need external media or peripheral devices to back up or restore hard disk data on this computer. At purchase, the Recover Pro is not installed. Install using the instructions below.The Recover Pro cannot back up or restore data correctly if a hard disk problem occurs during data backup or re-storing. If an error occurs due to an unexpected malfunction, incorrect operation, or other reason while data is being restored, the hard disk data (data before restoration) may be lost.Matsushita Electric Industrial Co., Ltd. will bear no responsibility for any damage suffered (including loss of data) as a result of the use of this function.The Recover Pro provides 3 types of backup as follows: Quick Backup: Scheduled backup of the updated data File Backup: File backup at ﬁ le save and change Complete Backup: Backup of the entire data on the internal hard diskHere, we will explain the procedures for installation, complete backup (backing up hard disk contents in case Windows can-not be booted), and complete restore (recovering the hard disk data to its condition at the time of the complete backup).For further information, refer to the software’s online manual ( page 20). CAUTION  All operations should be executed with the AC adaptor connected. Do not turn the power off while operations are in progress. If the power is turned off while installation, backup, or restore operations are in progress, these opera-tions may not function properly, and it may be impossible to start Windows. Also, do not press any keys or slide any switches, including hot keys. When restarting the computer, the message “Check ﬁ le system on C:” may appear. Follow the on-screen instruc-tions. Do not skip the check process. Make sure you allow enough space on the hard disk when choosing settings during installation. To change these settings you must reinstall Recover Pro. To execute Complete Backup reliably, we recommend performing [Typical] installation in the following cases. Hard disk with a single partition Immediately after reinstalling software (when more than half of the entire space of the hard disk is available) ( page 22) Be sure to use the internal hard disk drive to create the backup area. Never use disk or device other than the inter-nal hard disk drive. Some software (security software, backup software, encryption software, or hard disc accessible speciﬁ c software, etc.) may be incompatible with Recover Pro.For further information, refer to: http://www.phoenix.com/en/Customer+Services/White+Papers-Specs/Recover+Pro/default.htm When using Personal Secure Drive ( Installation Manual of “Trusted Platform Module (TPM)”), do not execute File Backup for Personal Secure Drive. The “Create recovery CD-DVD” function in Recover Pro is designed to help you save complete backup data to CD or DVD. When using the “Create recovery CD-DVD”, you can view the complete backup data on the hard disk, but take care to avoid accidentally deleting this data.  After installing the Recover Pro, do not use the IEEE1394 network connection. If any problem occurred, stop the IEEE1394 network connection and restart the computer.InstallationPreparation Connect the AC adaptor.1 Log on to Windows as an administrator.2 Close all programs.3 Disable anti-virus software.4 Click [start] - [Run], enter [c:\util\rcvpro\setup.exe], and click [OK].The InstallShield Wizard screen appears.5 Click [Next].Follow the on-screen instructions.Carefully read the License Agreement, and click [I accept the agreement.] The computer restarts several times to complete installation. appears in the notiﬁ cation area.$

Hard Disk Backup Function (Recover Pro)CAUTION Useful InformationDuring the installation, the screen may become black (no display) momentarily. This is not a malfunction. If you select [Typical] in installation, approximately 40% (max.) of the hard disk drive space is allocated as the back-up area. You cannot change the size of backup area after creation. Complete Backup Backs up all data on the hard disk. Preparation Connect the AC adaptor. 1 Log on to Windows as an administrator.2 Close all programs.3 Click [start] - [All Programs] - [Phoenix Applications] - [Phoenix Recover Pro 6].“Recover Pro 6” screen appears. 4 Click [Complete Backup], and click [Yes].  The computer restarts, and “Recover Pro 6” screen appears. Follow the on-screen instructions. NOTE  You can completely backup only one hard disk’s worth of data to the backup area.  Do not touch the power switch while using the Recover Pro. Complete Restore This function uses the data created during complete backup. It restores the hard disk data to the condition when you performed the complete backup. Files created and changes made to settings after the latest complete backup is made will be deleted. Preparation Connect the AC adaptor. 1 Click [start] - [All Programs] - [Phoenix Applications] - [Phoenix Always Launcher], and click [Run]. The computer restarts, and “Phoenix Always” screen appears. Alternatively turn on or restart the computer, and hold down F4 while [Panasonic] boot screen is displayed until “Phoenix Always” screen appears. 2 Click [Protect / Recover], and click [Phoenix Recover Pro 6]. “Recover Pro 6” screen appears. 3 Click [Complete Restore]. Follow the on-screen instructions. NOTE  Do not touch the power switch while using the Recover Pro. To access the online manual AClick [start] - [All Programs] - [Phoenix Applications] - [Docs], and double-click [UserGuides]. B Double-click the ﬁle of Recover Pro user’s guide or Phoenix Always user’s guide. 20

Hard Disk Data Erase UtilityWhen disposing the computer or transferring the ownership, erase all hard disk data in order to avoid data leakage. Even if you erase the data or initialize the hard disk using normal Windows commands, the data can be read with some special software. Use the hard disk data erase utility to erase the data completely.Note that transferring of the ownership without uninstalling the commercial software will be a violation of the software’s license agreement.The hard disk data erase utility erases data using an overwriting method, but there is a possibility that due to mal-functions or other operational errors, data may not be completely erased. There are also specialized devices that may be able to read data that has been erased using this method. If you need to erase highly conﬁdential data, we recommend that you contact a company that specializes in this process. Matsushita Electric Industrial Co., Ltd. will bear no responsibility for losses or damages suffered as a result of the use of this utility. CAUTION When the hard disk contains the Recover Pro backup data, the Recover Pro backup area is lost as well. NOTE This utility cannot erase data for speciﬁ c partitions. Preparation Prepare the following items: The Product Recovery DVD-ROM (included) Panasonic USB CD/DVD drive (optional) (refer to recent catalogs and other sources for information about the products available) Remove all peripherals (except for the CD/DVD drive). Connect the AC adaptor and do not remove it until hard disk data erase is complete. 1 Turn off the computer and connect the CD/DVD drive to the USB port ( page 11). 2 Turn on the computer, and press F2 several times while [Panasonic] boot screen is dis-played. The Setup Utility starts up.If the password is requested, enter the Supervisor Password.3 Select the [Boot] menu, then select [USB CDD] and press F6 until [USB CDD] is at the top of the boot priority order. 4 Set the Product Recovery DVD-ROM into the CD/DVD drive. 5 Press F10. At the conﬁrmation message, select [Yes] and press Enter. The computer restarts. 6 Press 2 to execute [2. [Erase HDD]]. To cancel this operation, press 0. 7 At the conﬁrmation message, press Y. 8 When [<<< Start Menu >>>] is displayed, press Enter. The approximate time required for erasing data will be displayed. 9 Press Space. At the conﬁrmation message, press Enter. The hard disk erase process starts. When the operation is completed, the [Hard disk data has been deleted.] message will appear. If a problem has occurred during the operation, an error message will appear.To cancel partway, press Ctrl + C. The data erasure will be up to that point.10 Remove the Product Recovery DVD-ROM, and then press any key to turn off the com-puter. 11 Remove the CD/DVD drive. Useful Information 21

22Useful InformationReinstalling SoftwareReinstalling software will return the computer to the default condition. When you reinstall the software, the hard disk data including the backup data of the Recover Pro will be erased.Back up important data to other media or an external hard disk before reinstallation.Preparation Prepare the following items: The Product Recovery DVD-ROM (included) Panasonic USB CD/DVD drive (optional) (refer to recent catalogs and other sources for information about the products available) Remove all peripherals (except for the CD/DVD drive). Connect the AC adaptor and do not remove it until reinstallation is complete. NOTE If you have installed the Recover Pro ( page 19), Select [1] or [2] in the step 9 below. If you select [3], the Recover Pro will no longer function properly. Only when you want to save the data which you stored in the separate partitions other than the ﬁ rst partition and the Recover Pro backup area, select [3] in the step 9 below and perform the following steps.A After reintallation, backup the data to external media (e.g., removable disk).B Perform the reinstallation procedure again, and select [1] or [2] in the step 9.C Return the data backed up in external media to the internal hard disk.1 Turn off the computer and connect the CD/DVD drive to the USB port ( page 11).2 Turn on the computer, and press F2 several times while [Panasonic] boot screen is dis-played.The Setup Utility starts up. If the password is requested, enter the Supervisor Password.3 Write down all of the contents of the Setup Utility and press F9.At the conﬁ rmation message, select [Yes] and press Enter.4 Select the [Boot] menu, then select [USB CDD] and press F6 until [USB CDD] is at the top of the boot priority order.5 Set the Product Recovery DVD-ROM into the CD/DVD drive.6 Press F10.At the conﬁ rmation message, select [Yes] and press Enter.The computer will restart.7 Press 1 to execute [1. [Recovery]].The License Agreement screen appears. To cancel partway, press 0.8 Press 1 to select [1. Yes, I agree to the provisions above and wish to continue!].9 Select the settings. [2]: Enter the size of operating system partition and press Enter.(The size of data partition will be determined by subtracting the operating system partition size from the maximum size.) [3]: Windows will be installed in the ﬁ rst partition. (The size of the ﬁ rst partition must be 20 GB or more. If smaller, installation will not be possible.)At the conﬁ rmation message, press Y.Reinstallation starts automatically. (It will take approximately 20 minutes.) Do not interrupt reinstallation, for example by turning off the computer or pressing Ctrl + Alt + Del. Oth-erwise reinstallation may become unavailable as Windows may not start up or the data may be corrupted.10 Remove the Product Recovery DVD-ROM, and then press any key to turn off the com-puter.11 Remove the CD/DVD drive.

12 Turn on the computer, and press F2 several times while [Panasonic] boot screen is dis-played. The Setup Utility starts up. If the password is requested, enter the Supervisor Password.13 Press F9. At the conﬁrmation message, select [Yes] and then press Enter. The Setup Utility settings excluding the password(s) will return to the default values. 14 Select the [Exit] menu and then select [Save Current Values], then press Enter. At the conﬁrmation message, select [Yes] and press Enter. 15 Turn the computer off by using the power switch. If additional instructions are included with the computer, be sure to read them. It may be necessary to per-form additional operations during the following procedure. 16 Perform the ﬁrst-time operation ( page 13).17 Start the Setup Utility and change the settings as necessary. Useful Information 23

Error Code/Message Follow the instructions below when an error message or code appears. If the problem persists or if the error code/mes-sage is not shown here, contact Panasonic Technical Support ( page 36). Troubleshooting Error Code/Message Solution 0211 Keyboard error  Disconnect external keyboard or mouse. 0251 System CMOS checksum bad -Default conﬁguration used An error has occurred in the memory of Setup Utility settings. This occurs when the memory content is changed by an unexpected program operation, etc.  Start the Setup Utility and return the settings to the default values, and then change the settings as necessary.  If the problem persists, the internal clock battery may need to be replaced. Contact Panasonic Technical Support ( page 36). 0271 Check date and time settings The date and time settings are not correct.  Start the Setup Utility and set the correct date and time.  If the problem persists, the internal clock battery may need to be replaced. Contact Panasonic Technical Support ( page 36). 0280 Previous boot incomplete - Default conﬁ guration used Startup has failed repeatedly, so the Setup Utility settings have been returned to the default values to startup the computer.  Start the Setup Utility and return the settings to the default values, and then change the settings as necessary. Press <F2> to Setup  Write down the error details and press F2 to start the Setup Utility. Change the settings if necessary. 0613: Serial Port*1 con-ﬁ guration changed 0614: Serial Port*1 conﬁg. error - device disabled *1 “A” or “B” appears here to indicate the name of the conﬂict-ing port. The I/O and IRQ settings of the serial ports are in conﬂict.  Run the Setup Utility and in the [Advanced] menu, change the port’s settings so there is no conﬂict. Operating System not found The operating system is not installed in the ﬂoppy disk or the hard disk that you are going to boot from.  If using a ﬂoppy disk, change the disk to the one you can use for boot.  If using the hard disk, check if the hard disk is recognized in [Information] menu of the Setup Utility. If the hard disk is recognized, perform the reinstallation ( page 22). If not, contact Panasonic Technical Support ( page 36).  If a device is connected to the USB port, disconnect the device, or set [USB Port] or [Legacy USB Support] to [Disable] in the [Advanced] menu of the Setup Utility.  If a device is connected to the ExpressCard slot, disconnect the device, or set [Express-Card slot] to [Disable] in the [Advanced] menu of the Setup Utility. RAM Module Failed When the RAM module is not inserted correctly or the RAM module is not conforming to the computer’s speciﬁcations, a beep will sound and the “RAM Module Failed” message will be displayed when you turn the power on.  Slide the power switch for four seconds or longer to turn off the computer, conﬁ rm that the RAM module conforms to the speciﬁcations, and reinsert it.  To start the Setup Utility ARestart the computer. B Press F2 several times while [Panasonic] boot screen is displayed. 24

Troubleshooting (Basic) Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the “Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact Panasonic Technical Support ( page 36). You can also check the computer’s status in the PC Information Viewer ( Reference Manual “Troubleshooting (Advanced)”).  Starting Up Cannot start up. The power indicator or bat-tery indicator is not lit.      Connect the AC adaptor. Insert a fully charged battery. Remove the battery pack and the AC adaptor, then connect them again. If a device is connected to the USB port, disconnect the device, or set [USB Port] or [Legacy USB Support] to [Disable] in the [Advanced] menu of the Setup Utility. If a device is connected to the ExpressCard slot, disconnect the device, or set [Ex-pressCard slot] to [Disable] in the [Advanced] menu of the Setup Utility. The power is turned on but “Warming up the system (up to 32 minutes)” appears.  The computer is warming up before start up. Wait for the computer to start up (takes up to 32 minutes). If, “Cannot warm up the system” is displayed, the computer failed to warm up and does not start. In this case, turn off the computer, leave it in an envi-ronment of 5 °C {41 °F} or higher temperature for about an hour, and then turn on the power again. Cannot turn on the computer. The computer does not re-sume from standby. (The power indicator blinks quickly in green.)  Leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, then turn on the power again. You have forgotten the pass-word.  Supervisor Password or User Password: Contact Panasonic Technical Support ( page 36). Administrator password:  If you have a password reset disk, you can reset the administrator password. Set thedisk and enter any wrong password, then follow the on-screen instructions and set anew password.  If you do not have a password reset disk, reinstall ( page 22) and set up Windows,and then set a new password. “Remove disks or other media. Press any key to restart” or a similar message appears.    A ﬂoppy disk is in the drive and it does not contain system startup information. Remove the ﬂoppy disk and press any key. If a device is connected to the USB port, disconnect the device, or set [USB Port] or [Legacy USB Support] to [Disable] in the [Advanced] menu of the Setup Utility. If a device is connected to the ExpressCard slot, disconnect the device, or set [Ex-pressCard slot] to [Disable] in the [Advanced] menu of the Setup Utility. If the problem persists after removing the disk, it may be a hard disk failure. Contact Panasonic Technical Support ( page 36). Windows startup and opera-tion is slow.   Press F9 in the Setup Utility ( page 24 “To start the Setup Utility”) to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again. (Note that the processing speed depends on the applica-tion software, so this procedure may not make Windows faster.) If you installed a resident software after purchase, turn off the residence. Disable Indexing Service in the following menu. Click [start] - [Search] - [Change preferences] - [Without Indexing Service] The date and time are incor-rect.     Make the correct settings. Click [start] - [Control Panel] - [Date, Time, Language, and Regional Options] - [Date and Time]. If the problem persists, the internal clock battery may need to be replaced. Contact Panasonic Technical Support ( page 36). When the computer is connected to LAN, check the date and time of the server. The 2100 A.D. or later year will not be correctly recognized on this computer. [Executing Battery Recali-bration] screen appears.  The Battery Recalibration was canceled before Windows was shut down last time. To start up Windows, turn off the computer by the power switch, and then turn on. [Enter Password] does not appear when resuming from standby/hibernation.  To display [Enter Password] at resuming, set the Windows password. The password you have set in the Setup Utility is not requested at resuming. AClick [start] - [Control Panel] - [User Accounts] and select the account, and set the password. BClick [start] - [Control Panel] - [Performance and Maintenance] - [Power Options] -[Advanced] and add a check mark for [Prompt for password when computer resumes from standby]. Troubleshooting 25

Troubleshooting (Basic) Starting Up Cannot resume. Other startup problems. An error may occur when the computer automatically enters the standby or hibernation mode while the screensaver is active. In this case, turn off the screensaver or change the pattern of the screensaver.  Press F9 in the Setup Utility ( page 24 “To start the Setup Utility”) to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again. Remove all peripheral devices. Check to see if there was a disk error. AClick [start] - [My Computer] and right-click [Local Disk(C:)], and click [Properties]. BClick [Tools] - [Check Now]. CSelect the option in [Check disk options] and click [Start]. Start the computer in Safe Mode and check the error details. When the [Panasonic] boot screen disappears*1 at startup, press and hold F8 until the Windows Advanced Options Menu is displayed.*1 When [Password on boot] is set to [Enable] in the [Security] menu of the Setup Utility, [Enter Password] appears after the [Panasonic] boot screen disappears. As soon as you enter the password and press Enter, press and hold F8.  Entering Password On the [Enter Password] screen, a beep sounds and the password cannot be entered.  The computer may be in ten-key mode. If the NumLk indicator lights, press NumLk to disable the ten-key mode, and theninput. Even after entering the pass-word, [Type your password] is displayed again.  The computer may be in ten-key mode. If the NumLk indicator lights, press NumLk to disable the ten-key mode, and theninput.  The computer may be in Caps Lock mode. If the Caps Lock indicator lights, press Caps Lock to disable the Caps Lockmode, and then input.  Shutting down  Remove the USB device and the ExpressCard.  Wait one or two minutes. It is not a malfunction. Windows does not shut down.  Display No display.      The external display is selected. Press Fn + F3 to switch the display. Wait until the display has been switched completely before pressing Fn + F3 again.When using an external display, Check the cable connection. Turn on the display. Check the settings of external display. The display is turned off by the power-saving function. To resume, do not press the direct selection keys, but press any other key like Ctrl. The computer entered standby or hibernation by the power-saving function. To resume, slide the power switch. The screen may not be displayed even after the computer resumed from standby or hi-bernation. In this case, press Fn+ F7 to enter standby and resume the computer again. The screen is dark.  The screen is darker when the AC adapter is not connected. Press Fn + F2 and adjustthe brightness. As you increase the brightness, battery consumption increases. You can separately set the brightness for when the AC adaptor is connected and when not connected. The LCD brightness chang-es a number of times when the AC adaptor is discon-nected.  Intel(R) Display Power Saving Technology is active and automatically changes the LCD brightness. This is not a malfunction. Troubleshooting 26

$27Troubleshooting DisplayImage colors are not repro-duced as expected when displaying photographs or other images. Remove the check mark of [Intel(R) Display Power Saving Technology].A Click [start] - [Control Panel] - [Other Control Panel Options] - [Intel(R) GMA Driver for Mobile].B Click [Display Settings] - [Power Settings].The screen is disordered.  Changing the number of display colors and resolution may affect the screen. Restart the computer. Connecting/disconnecting an external display may affect the screen. Restart the com-puter. When using Simultaneous display, set the same display colors for the external display as those for the LCD. When using Simultaneous display, do not press Fn + F3. Enable or disable Simultaneous display, and soon restart the computer.During Simultaneous display, one of the screens becomes disordered. When using the Extended Desktop, use the same display colors for the external display as those used by the LCD. If you continue to experience problems, try changing the display by clicking [start] - [Control Panel] - [Other Control Panel Options] - [Intel(R) GMA Driver for Mobile] - [Dis-play Devices]. When the [Command Prompt] is set to “Full Screen” by pressing Alt + Enter, the picture is displayed on one of the screens only. When the window display is restored by pressing Alt + Enter, the picture is displayed on both screens. Simultaneous display cannot be used until Windows startup is complete (during Setup Utility, etc.).The external display does not work normally. If the external display does not support the power saving function, it may not work nor-mally when the computer enters the power saving mode. Turn off the external display. Touch Pad / Touchscreen (only for model with touchscreen)/Digitizer (only for model with digitizer)The cursor does not work.  When using the external mouse, connect it correctly. Restart the computer using the keyboard. (Press , U, and R to select [Restart].) If the computer does not respond to keyboard commands, read “No response” ( page 28).Cannot input using the touch pad. Set [Touch Pad] to [Enable] in the [Main] menu of the Setup Utility. The drivers for some mice may disable the touch pad. Check your mouse’s operating instructions.Cannot point the correct position using the included stylus/pen.<Only for model with touchscreen> Perform the touchscreen calibration ( page 15).<Only for model with digitizer> Perform the digitizer calibration. Use the included pen. On the Windows logon screen or the Welcome screen, you may not be able to point the correct position using the included pen. Use the keyboard or the touch pad to log on. Reference ManualThe Reference Manual is not displayed. Install Adobe Reader.A Log on to Windows as an administrator.B Click [start] - [Run], input [c:\util\reader\AdbeRdr70_enu_full.exe], then click [OK].Follow the on-screen instructions.C Update Adobe Reader to its latest version.If your computer is connected to the internet, start up Adobe Reader and click [Help] - [Check for updates now].$

28Troubleshooting Recover ProCannot install Recover Pro  Recover Pro cannot be installed when four primary partitions exist. Reduce the number of primary partitions to three or less before installation. You can check the number of the primary partitions in the order of [start] - [Control Panel] - [Performance and Mainte-nance] - [Administrative Tools] - [Computer Management] - [Disk Management]. Recover Pro cannot be installed when a backup area is remaining on the hard disk. Try one of the following methods: If the backup area has complete backup data and you want to restore that data:Follow the “Complete Restore” instructions in “Hard Disk Backup Function (Recover Pro)” ( page 20) to restore the data. To return the computer to its condition at the time of shipment:Reinstall the software ( page 22). In step 9, do not select “3. Reinstall Windows to the ﬁ rst partition.” If you do not need the data in the backup area, or if it is corrupted, or if does not in-clude complete backup data: A Access [http://www.phoenix.com/en/Customer+Services/Utilities/Recover+Pro+6.htm#Where], and download/install “Cleanup Utility for Recover Pro 6”. B Delete the backup area using “Cleanup Utility for Recover Pro 6”.C Reinstall Recover Pro.In this case, all data in the backup area will be lost. An unnecessary backup area is present (is left) when Recover Pro is not installed.A Access [http://www.phoenix.com/en/Customer+Services/Utilities/Recover+Pro+6.htm#Where], and download/install “Cleanup Utility for Recover Pro 6”. B Delete the backup region using “Cleanup Utility for Recover Pro 6”.Some parts of the hard disk cannot be File Backed up. The hard disk area encrypted by security software may not be backed up. Exclude the area from the File Backup object. OthersNo response.  Press Ctrl+Shift+Esc to open Task Manager and close the software application that is not responding. An input screen (e.g., password input screen at startup) may be hidden behind another window. Press Alt+Tab to check. Slide the power switch for four seconds or longer to shut down the computer, and then slide the power switch to turn it on. If the application program does not work normally, uninstall and reinstall the program. To uninstall, click [start] - [Control Panel] - [Add or Remove Programs].Troubleshooting (Basic)

Hardware Diagnostics If it appears that the hardware installed in this computer is not operating properly, you can use the PC-Diagnostic Utility to determine whether or not there is a problem. If the utility discovers a problem in the hardware, contact Panasonic Technical Support.Hardware that can be checked using the PC-Diagnostic Utility Software cannot be checked using this utility.  CPU  Memory  Hard Disk  Video Controller  Sound*1  Modem  LAN  Wireless LAN*2  Wireless WAN*3  Bluetooth*4  GPS*5  USB  IEEE 1394  PC Card Controller  SD Card Controller  Serial Port  Keyboard  Touch Pad  Touchscreen*6  Digitizer*7 *1 When the diagnostic utility is running, a loud beep will sound, so do not use headphones at this time. (The beep will *2 *3 *4 *5 *6 *7 not sound if mute is using Windows.) Only for model with wireless LAN Only for model with wireless WAN Only for model with Bluetooth Only for model with GPS Only for model with touchscreen Only for model with digitizer. The display icon is “Touch Screen”. Regarding the PC-Diagnostic Utility NOTE Run this utility using the default settings in the Setup Utility. If the Setup Utility or other settings will not allow a hard-ware to be executed, the hardware icon will be displayed in gray. For the hard disk and memory only, you can select standard diagnostic check or extended diagnostic check. When the PC-Diagnostic Utility starts up, it will run the standard diagnostic check. The extended diagnostic check is more detailed, and so requires a longer period of time to run. When the video diagnostic check is running, the display may be distorted, and when the audio diagnostic check is running, sounds may be generated from the speakers. These are not malfunctions. You can check the status of the diagnostic check by the display color on the left side of the hardware icon (A). Aqua: Not running diagnostic check Alternating blue and yellow: Currently running diagnostic check. The interval of the alternating colors dif-fers depending on the type of diagnostic check currently running. During memory diagnostic check, the display may freeze for a long period of time. Wait until the process Ais complete. Green: No problems discovered Red: Problems discovered Troubleshooting 29

30Troubleshootingz We recommend that you use the touch pad for operations. When not using the touch pad, you can operate using the internal keyboard instead. Do not use the touchscreen or the digitizer.Operations Touch pad operations Internal keyboard operationsSelect icon Place the cursor above the icon Press Space. and then press Î Í Ï Ð ( (close) cannot be selected)Click the icon Tap or click (right click cannot be used) Press Space above the iconComplete the PC-Diagnos-tics Utility and then restart the computerClick (close) Press Ctrl+Alt+Del.z By clicking the icon, you can execute the following operations:y : Start the diagnostic check from the beginningy : Stop the diagnostic check (You cannot restart the check partway through by clicking )y : Display help (click the screen or press Space to return to the original diagnostic check screen)Running the Diagnostic CheckDisconnect any peripheral devices (e.g., storage device) before running the diagnostic check. 1 Connect the AC adaptor and turn on the wireless switch (Î page 11).During the diagnostic check, do not remove the AC adaptor, or attach any peripheral devices.2 Turn on or restart the computer, and press F2 while [Panasonic] boot screen is dis-played.The Setup Utility starts up.z If the password is requested, enter the Supervisor Password.z If you are using the computer after changing the settings from the status at the time of purchase, we recom-mend that you make a note of the settings that are changed.3 Press F9.At the conﬁ rmation message, select [Yes] and press Enter.4 Press F10.At the conﬁ rmation message, select [Yes] and press Enter.The computer will restart.5 Press Ctrl+ F7 while [Panasonic] boot screen is displayed.When the PC-Diagnostic Utility starts up, it will automatically begin the diagnostic check for all hardware compo-nents.z If the password is requested, enter the password.z The touch pad and the internal keyboard cannot be used until alternating blue and yellow colors are dis-played on the left side of the hardware icon (Î page 29). If the touch pad does not operate properly, press Ctrl+Alt+Del to restart the computer, or slide the power switch to turn the power off, and then restart the PC-Diagnostic Utility. NOTE z Using the following procedure, you can run a diagnostic check on a speciﬁ ed hardware component, or run an extended diagnostic check on the hard disk.A Click to stop the diagnostic check.B Click the icon for the hardware that is not to be checked, so that the icon is displayed in gray (B).When running a check on the hard disk, clicking the icon once will turn on the extended diagnostic check (“FULL” (C) will be displayed below the icon); click again, and the icon will be displayed in gray. C Click to start the diagnostic check. CHardware Diagnostics

6 7 When all the hardware has been checked, conﬁrm the diagnostic check results. If the display is red and the message “Check Result TEST FAILED” is displayed, you can assume that there is a problem with the computer’s hardware. Conﬁrm which hardware component is displayed as red, and contact Panasonic Technical Support. If the display is green and the message “Check Result TEST PASSED” is displayed, the computer’s hardware is operating normally. Continue using the computer as is. If the computer still does not operate properly, reinstall the software. ( page 22) NOTE If you run a memory diagnostic check after installing a new RAM module (sold separately) and the message “Check Result TEST FAILED” is displayed: Remove the additional RAM module and run the diagnostic check again. If the message “Check Result TEST FAILED” is still displayed, you can assume that there is a problem with the internal RAM module. After the diagnostic check is complete, click (close), or press Ctrl+Alt+Del to re-start the computer. Troubleshooting 31

LIMITED USE LICENSE AGREEMENTAppendix THE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC® PRODUCT (“PROD-UCT”) ARE LICENSED ONLY TO THE END-USER (“YOU”), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY DEEMED TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE. Matsushita Electric Industrial Co., Ltd. (“MEI”) has developed or otherwise obtained the Programs and hereby licenses their use to you. You assume sole responsibility for the selection of the Product (including the associated Programs) to achieve your intended results, and for the installation, use and results obtained therefrom. LICENSE A. MEI hereby grants you a personal, non-transferable and non-exclusive right and license to use the Programs in accordance with the terms and conditions stated in this Agreement. You acknowledge that you are receiving only a LIMITED LICENSE TO USE the Programs and related documentation and that you shall obtain no title, ownership nor any other rights in or to the Programs and related documentation nor in or to the algorithms, concepts, designs and ideas represented by or incorporated in the Programs and related documentation, all of which title, ownership and rights shall remain with MEI or its suppliers. B. You may use the Programs only on the single Product which was accompanied by the Programs. C. You and your employees and agents are required to protect the conﬁdentiality of the Programs. You may not distrib-ute or otherwise make the Programs or related documentation available to any third party, by time-sharing or other-wise, without the prior written consent of MEI. D. You may not copy or reproduce, or permit to be copied or reproduced, the Programs or related documentation for any purpose, except that you may make one (1) copy of the Programs for backup purposes only in support of your use of the Programs on the single Product which was accompanied by the Programs. You shall not modify, or at-tempt to modify, the Programs. E. You may transfer the Programs and license them to another party only in connection with your transfer of the single Product which was accompanied by the Programs to such other party. At the time of such a transfer, you must also transfer all copies, whether in printed or machine readable form, of every Program, and the related documentation, to the same party or destroy any such copies not so transferred. F. You may not remove any copyright, trademark or other notice or product identiﬁcation from the Programs and you must reproduce and include any such notice or product identiﬁcation on any copy of any Program. YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANICALLY OR ELECTRONICALLY TRACE THE PROGRAMS, OR ANY COPY THEREOF, IN WHOLE OR IN PART. YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PROGRAMS OR ANY COPY THEREOF, IN WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE. IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO ANOTHER PARTY, EXCEPT AS PER-MITTED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY TERMINATED. TERM This license is effective only for so long as you own or lease the Product, unless earlier terminated. You may termi-nate this license at any time by destroying, at your expense, the Programs and related documentation together with all copies thereof in any form. This license will also terminate effective immediately upon occurrence of the conditions thereof set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein. Upon any such termination, you agree to destroy, at your expense, the Programs and related documentation together with all copies thereof in any form. YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT IT IS THE COMPLETE AND EXCLUSIVE STATE-MENT OF THE AGREEMENT BETWEEN US, WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT, ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MAT-TER OF THIS AGREEMENT. About Intel® software products The enclosed software products and documentation were developed at private expense, and are provided with “RE-STRICTED RIGHTS.” Use, duplication or disclosure by the government is subject to restrictions as set forth in FAR 52.227-14 and DFARS 252.227-7013 et. seq. or its successor. The use of this product by the government constitutes acknowledgment of Intel’s proprietary rights in the product. 32

Contrat de licence d’usage limitéLe(s) logiciel(s) (les “Logiciels”) fournis avec ce produit Panasonic® (le “Produit”) sont exclusivement concédés en licence à l’utilisateur ultime (“vous”), et ils ne peuvent être utilisés que conformément aux clauses contractuelles cides-sous. En utilisant les logiciels, vous vous engagez de manière déﬁnitive à respecter les termes, clauses et conditions des présentes. Matsushita Electric Industrial Co., Ltd. (“MEI”) a mis au point ou obtenu les Logiciels et vous en concède l’utilisation par les présentes. Vous assumez l’entière responsabilité du choix de ce Produit (y compris des Logiciels associés) pour obtenir les résultats escomptés, ainsi que de l’installation, de l’utilisation et des résultats obtenus. Licence A. MEI vous octroie par les présentes le droit et la licence personnels, non cessibles et non exclusifs d’utiliser les Logiciels conformément aux termes, clauses et conditions de ce contrat. Vous reconnaissez ne recevoir qu’un droit limité d’utiliser les Logiciels et la documentation les accompagnant et vous vous engagez à n’obtenir aucun droit de titre, propriété ni aucun autre droit vis-à-vis des Logiciels et de la documentation les accompagnant ni vis-à-vis des algorithmes, concepts, dessins, conﬁgurations et idées représentés par ou incorporés dans les Logiciels et la documentation les accompagnant, dont les titres, propriété et droits resteront tous à MEI ou à leurs propriétaires. B. Vous ne pouvez utiliser les Logiciels que sur le Produit unique qui est accompagné par les Logiciels. C. Vous et vos employés ou agents êtes requis de protéger la conﬁdentialité des Logiciels. Vous ne pouvez ni dis-tribuer ni mettre les Logiciels et la documentation les accompagnant à la disposition d’un tiers, par partage de temps ou de quelque autre manière que ce soit, sans l’autorisation écrite préalable de MEI. D. Vous ne pouvez ni copier ni reproduire ni permettre la copie ni la reproduction des Logiciels ni de la documenta-tion les accompagnant pour quelque ﬁn que ce soit, à l’exception d’une (1) copie des Logiciels à des ﬁns de sau-vegarde uniquement pour soutenir votre utilisation des Logiciels sur le Produit unique qui est accompagné par les Logiciels. Vous ne pouvez ni modiﬁer ni tenter de modiﬁer les Logiciels. E. Vous ne pouvez céder les Logiciels et en octroyer la licence à une autre partie qu’en rapport avec votre cession du Produit unique qui est accompagné par les Logiciels à cette autre partie. Au moment de cette cession, vous devez céder également toutes les copies, que ce soit sous forme imprimée ou lisible par la machine, de tous les Logiciels ainsi que de la documentation les accompagnant, à la même partie ou détruire les copies non cédées. F. Vous ne pouvez retirer aucune marque de droits d’auteur, marque de commerce ou autre ni aucune identiﬁcation de produit des Logiciels et vous devez reproduire et inclure toutes ces notices ou identiﬁcations de produit sur toutes les copies des Logiciels. Vous ne pouvez assembler en sens inverse, compiler en sens inverse ni retracer les Logiciels ni aucune de leurs cop-ies, de façon électronique ou mécanique, en tout ou en partie. Vous ne pouvez utiliser, copier, modiﬁer, altérer ni céder les Logiciels ni aucune de leurs copies, en tout ou en partie, à l’exception de ce qui est expressément stipulé dans ce contrat. Si vous cédez la possession de toute copie ou de tout Logiciel à une autre partie, à l’exception de ce qui est autorisé au paragraphe E ci-dessus, votre licence est automatiquement résiliée. Termes, clauses et conditions Cette licence n’est effective que pour la durée de possession ou de crédit-bail du Produit, à moins d’une résiliation an-térieure. Vous pouvez résilier cette licence à tout moment en détruisant, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme que ce soit. Cette licence sera également résiliée, avec application immédiate, si les conditions de résiliation déﬁnies ailleurs dans ce contrat se sont réalisées ou si vous ne respectez pas les termes, clauses et conditions qui y sont contenues. Au moment de la résiliation, vous acceptez de détruire, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme que ce soit. Vous reconnaissez avoir lu ce contrat, en avoir compris toute la substance et avoir accepté de respecter ses termes, clauses et conditions. Vous reconnaissez en outre qu’ils sont la description complète et exclusive du contrat conclu entre nous, contrat qui remplace et annule toute proposition ou contrat précédent, écrit ou oral, et toute autre commu-nication entre nous, relativement à l’objet du présent contrat. Appendix 33

34AppendixSpeciﬁ cationsThis page provides the speciﬁ cations for the basic model CF-19CHBAXBM/CF-19CDBAXVM. The model number is different according to the unit conﬁ guration.z To check the model number:Check the bottom of the computer or the box the computer came in at the time of purchase.z To check CPU speed, memory size and the hard disk drive (HDD) size:Run the Setup Utility (Î Reference Manual “Setup Utility”) and select [Information] menu.[CPU Speed]: CPU speed, [System Memory]: Memory size, [Hard Disk]: Hard disk drive size Main Speciﬁ cationsModel No. CF-19CHBAXBM CF-19CDBAXVMCPU Intel® Core™ Duo Processor U2400 (1.06 GHz, 2 MB*1 L2 cache, 533 MHz FSB)Chipset Intel® 945GMMemory*1*2 512 MB (4096 MB Max.)Video Memory*1*3 UMA (128 MB Max.)Hard Disk Drive*4 80 GBDisplay Method 10.4 XGA type (TFT)Internal LCD*5 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots)External Display*6 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1280 × 768 dots/1280 × 1024 dots)Wireless LAN*7 Î page 35BluetoothTM *8 Î page 35LAN IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TXModem Data: 56 kbps (V.92) FAX: 14.4 kbpsSound WAVE and MIDI playback, Intel® High Deﬁ nition Audio subsystem support, Monaural speakerSecurity Chip TPM (TCG V1.2 compliant)*9Card Slot PC Card Type I or Type II x 1 (3.3 V: 400 mA, 5 V: 400 mA)ExpressCard ExpressCard/34*10 or ExpressCard/54 x 1SD Memory Card*11 x 1, Data transfer rate = 8 MB per second*12RAM Module Slot 200-pin, 1.8 V, SO-DIMM, DDR2 SDRAM, PC2-4200 CompliantInterface USB port (4-pin, USB 2.0) x 2, Serial Port (Dsub 9-pin male), Modem port (RJ-11), LAN port (RJ-45), External display port (Mini Dsub 15-pin female), Expansion Bus Connector (Dedicated 100-pin female), External Antenna Connector (Dedicated 50 Ω coaxial connector) x 2, IEEE 1394a Interface Connector (4-pin x 1), Microphone Jack (Miniature jack, 3.5 DIA, Stereo), Headphone Jack (Miniature jack, 3.5 DIA, Impedance 32 Ω, Output Power 4 mW × 2)Keyboard / Pointing Device 82 keys / Touch Pad / Touchscreen (Anti-Reﬂ ection, Stylus (included) touch capable) 82 keys / Touch Pad / Digitizer (Anti-Reﬂ ec-tion)Power Supply AC adaptor or Battery packAC Adaptor*13 Input: 100 V to 240 V AC, 50 Hz/60 Hz, Output: 16.0 V DC, 3.75 ABattery Pack Li-ion 10.65 V, 5.7 AhOperating Time*14 Approx. 4.5 hours to 8 hours*15 (Approx. 7 hours*16)Charging Time*14Power on Approx. 7.5 hoursPower off Approx. 4.5 hoursClock Battery Coin type lithium battery 3.0 VPower Consumption*17 Approx. 26 W*18 / Approx. 55 W (Maximum when recharging in the ON state)Physical Dimensions (W × H × D)(excluding the hand strap/shoul-der strap)271 mm × 49 mm × 216 mm {10.7" × 1.93" × 8.5"}Weight (excluding the hand strap/shoul-der strap)Approx. 2.25 kg {Approx. 4.96 lb.} Approx. 2.30 kg {Approx. 5.07 lb.}Operation Environment Temperature: 5 °C to 35 °C {41 °F to 95 °F}Humidity: 30% to 80% RH (No condensation)Storage Environment Temperature: -20 °C to 60 °C {-4 °F to 140 °F}Humidity: 30% to 90% RH (No condensation)

$35Appendix Main Speciﬁ cationsOperating System Microsoft® Windows® XP Professional Service Pack 2 with Advanced Security Technologies (NTFS File System)Microsoft® Windows® XP Tablet PC Edition 2005(NTFS File System)Utility Programs DMI Viewer, Microsoft® Windows® Media Player 10, Adobe Reader, PC Information Viewer, SD Utility, Icon Enlarger, Loupe Utility, Intel® Matrix Storage Manager, Intel® PROSet/Wireless Software*7, Bluetooth™ Stack for Windows® by TOSHIBA*8 , Wireless Switch Utility, Hotkey Settings, Battery Recalibration Utility, Panasonic Hand Writing*19, Software Keyboard*19, Dis-play Rotation Tool, Inﬁ neon TPM Professional Package*20, Recover ProTM 6*20 , Tablet Buttons Settings*19Setup Utility, Hard Disk Data Erase Utility*21, PC-Diagnostic Utility Wireless LAN <Only for model with wireless LAN>Intel PRO / Wireless 3945 ABG (802.11 a + b + g)Data Transfer Rates*22 IEEE802.11a: 54/48/36/24/18/12/9/6 Mbps (automatically switched)IEEE802.11b: 11/5.5/2/1 Mbps (automatically switched)IEEE802.11g: 54/48/36/24/18/12/9/6 Mbps (automatically switched)Standards Supported IEEE802.11a/IEEE802.11b/IEEE802.11gTransmission method OFDM system, DSSS systemWireless Channels Used IEEE802.11a: Channels 36/40/44/48/52/56/60/64/149/153/157/161/165IEEE802.11b/IEEE802.11g: Channels 1 to 11RF Frequency Band IEEE802.11a: 5.18-5.32 GHz, 5.745-5.825 GHzIEEE802.11b/IEEE802.11g: 2.412-2.462 GHz BluetoothTM <Only for model with Bluetooth>Bluetooth Version 2.0 + EDRTransmission method FHSS systemWireless Channels Used Channels 1 to 79RF Frequency Band 2.402-2.48 GHzPower Class Class1 *1 1 MB = 1,048,576 bytes*2 You can physically expand the memory upto 4 GB, but the total amount of usable memory available will be less depending on the actual system conﬁ guration. *3 A segment of the main memory is allotted automatically depending on the computer’s operating status. The size of the Video Memory cannot be set by the user.*4 1 GB = 1,000,000,000 bytes. Your operating system or some application software will report as fewer GB.*5 A 16,777,216 color display is achieved by using the dithering function.*6 Maximum resolution depends on the speciﬁ cations of the external display.*7 Only for model with wireless LAN*8 Only for model with Bluetooth*9 For information on TPM, click [start] - [Run] and input “c:\util\drivers\tpm\README.pdf”, and refer to the Installation Manual of “Trusted Platform Module (TPM)”.*10 When using ExpressCard/34, the card slot cover cannot be closed.*11 Operation has been tested and conﬁ rmed using Panasonic SD Memory Cards with a capacity of up to 2 GB. The transfer rate using the SD Memory Card slot on this computer is 8 MB per second. (This is a theoretical value, and differs from actual speeds.) The transfer rate is 8 MB per second even if you use an SD Memory Card that supports high-speed transfer rates. Operation on other SD equipment is not guaranteed. This computer is not compatible with MultiMediaCards or SDHC Memory Cards. Do not insert these kinds of cards.*12 Theoretical value and not the actual speed. The transfer rate does not become higher even if you use a card that supports the higher transfer rate.*13 The AC adaptor is compatible with power sources up to 240 V AC adaptor. The computer is supplied with a 125 V AC compat-ible AC cord. 20-M-2-1*14 Varies depending on the usage conditions.*15 Measured using BatteryMark™ Version 4.0.1 (LCD brightness: Maximum - Minimum)*16 Measured using MobileMark™ 2005 (LCD brightness: 60 cd/m2)*17 Approx. 26 W when the battery pack is fully charged (or not being charged) and the computer is OFF. Approx. 1.2 W when the Wake up from LAN has been enabled.*18 Rated power consumption 23-E-1*19 Only for model with Windows XP Professional*20 You need to install to use the feature.*21 The Product Recovery DVD-ROM is required.*22 These are speeds speciﬁ ed in IEEE802.11a+b+g standards. Actual speeds may differ.$

Panasonic of North America 9TGCF-194 Personal Computer Model CF-19 Family User Manual CF 19CTQZZBM indb

Panasonic Corporation of North America Personal Computer Model CF-19 Family CF 19CTQZZBM indb

Contents

User Manual for CF19

Navigation menu

Namespaces

Views

Navigation