Panasonic of North America 9TGCF-195 Personal Computer CF-19 Family User Manual CF 19CTQZZBM indb

Panasonic Corporation of North America Personal Computer CF-19 Family CF 19CTQZZBM indb

User Manual Summary for FCC Warning Notices

Contents
Getting Started
OPERATING INSTRUCTIONS
Personal Computer
Model No. CF-19 series
Introduction ................................................................. 2
Read Me First ............................................................. 3
Description of Parts ..................................................10
First-time Operation ..................................................13
Useful Information
On-screen Manual ....................................................16
Handling and Maintenance .......................................17
Hard Disk Backup Function (Recover Pro) ..............19
Hard Disk Data Erase Utility .....................................21
Reinstalling Software ................................................22
Troubleshooting
Error Code/Message ................................................24
Troubleshooting (Basic) ............................................25
Hardware Diagnostics ..............................................29
Appendix
LIMITED USE LICENSE AGREEMENT ...................32
Specifi cations ...........................................................34
LIMITED WARRANTY ..............................................36
Please read these instructions carefully before using this product and save this manual for future use.
For further information about the com-
puter, you can refer to the on-screen
manual.
To access the on-screen manual
Î page 16 “On-screen Manual”
Getting StartedUseful InformationTroubleshootingAppendix
3
Getting Started
Read Me First
Models for U.S.A.
Federal Communications Commission Radio Fre-
quency Interference Statement
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
Consult the Panasonic Service Center or an experi-
enced radio/TV technician for help.
Warning
To assure continued compliance, use only shielded inter-
face cables when connecting to a computer or peripheral.
Also, any changes or modifications not expressly ap-
proved by the party responsible for compliance could void
the user’s authority to operate this equipment.
FCC RF Exposure Warning:
This equipment is provided with PC Card slot that could
be used with wireless transmitters, which will be specifi-
cally recommended when they become available.
Other third-party wireless transmitters have not been
RF exposure evaluated for use with this computer and
may not comply with FCC RF exposure requirements.
<Only for model with wireless LAN/Bluetooth>
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment.
This equipment may not be co-located or operated
with any other antenna or transmitter.
This equipment has been approved for portable operation,
and unless otherwise advised in separate supplemental
instructions for individual wireless transmitter(s), requires
minimum 1.5 cm spacing be provided between antenna(s)
and all person’s body (excluding extremities of hands,
wrist and feet) during wireless modes of operation.
This equipment may use multiple installed transmitters,
which may be capable of simultaneous transmission.
This equipment is provided with external antenna
connector(s) for connection to optional Car Mounter or
Port Replicator for mobile external mounted antenna(s).
External antenna(s) must be professionally installed and
cannot exceed recommended maximum antenna gain as
described in individual provided supplement instructions
for wireless transmitters. Also, user must maintain mini-
mum 20 cm spacing between external antenna(s) and all
person’s body (excluding extremities of hands, wrist and
feet) during wireless modes of operation.
<Only for model with wireless LAN>
WLAN external antenna connector is intended for con-
nection to Radiall/Larsen WLAN Base Whip antenna,
type NM05E2400BKTNC with 5 dBi antenna.
<Only for model with wireless WAN>
WWAN external antenna connector is intended for
professional installation and should not exceed maxi-
mum antenna gain of 9.85 dBi for 824.7 - 848.31 MHz
operation and 8.34 dBi for 1851.25 - 1908.75 MHz
operation.
This device complies with Part 15 of the FCC Rules. Op-
eration is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired op-
eration.
Responsible Party: Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Tel No:1-800-LAPTOP5 (1-800-527-8675)
6-M-1
FCC Regulation Notice for modem
This equipment contains a FCC approved modem.
1. This equipment complies with CFR47 Part 68 rules.
On the computer is a label that contains, among other
information, the FCC registration number and ringer
equivalence number (REN) for this equipment. If re-
quired, this information must be provided to the tele-
phone company.
2. An FCC compliant telephone cord and modular plug
is provided with this equipment. This equipment is
designed to be connected to the telephone network
or premises wiring using a compatible modular jack
which is Part 68 compliant. See Installation Instruc-
tions for details.
3. The REN is used to determine the quantity of devices
which may be connected to the telephone line. Ex-
cessive RENs on the telephone line may result in the
devices not ringing in response to an incoming call. In
most, but not all area, the sum of RENs should not ex-
ceed five (5.0). To be certain of the number of devices
that may be connected to a line, as determined by the
total RENs, contact the local telephone company.
4. If your telephone equipment cause harm to the tele-
phone network, the telephone company will notify you
in advice that temporary discontinuance of service
may be required. But if advice notice isn’t practical, the
telephone company will notify the customer as soon
as possible. Also, you will be advised of your right to
file a complaint with the FCC if you believe it is neces-
sary.
5. The telephone company may take changes in its facili-
ties, equipment, operations or procedures that could
affect the operation of the equipment. If this happens
the telephone company will provide advance notice
in order for you to make necessary modifications to
maintain uninterrupted service.
6. If trouble is experienced with this equipment, for repair
or warranty information, please contact Panasonic
Corporation of North America at DIAL TOLL FREE
1-800-LAPTOP5 (1-800-527-8675). If the equipment is
causing harm to the telephone network, the telephone
company may request that you disconnect the equip-
ment until the problem is resolved.
7. There are no user serviceable parts contained in this
equipment.
8. This equipment may not be used on coin service pro-
vided by the telephone company. Connection to party
lines is subject to state tariffs.
5
Getting Started
CSA C22 2 NO.213-conforming model. (The model
which has description of “CSA C22 2 NO.213” in the
bottom of the computer.)
z THIS EQUIPMENT IS SUITABLE FOR USE IN
CLASS I, DIVISION2, GROUPS A, B, C, AND D OR
NON-HAZARDOUS LOCATIONS ONLY.
z WARNING-EXPLOSION HAZARD-SUBSTITUTION
OF COMPONENTS MAY IMPAIR SUITABILITY FOR
CLASS I, DIVISION2.
z When connecting and using a device manufactured by
a third party, enquire to the manufacturer as to wheth-
er the device suits CLASS I, DIVISION2. 33-Ca-1
<Only for model with wireless LAN/Bluetooth>
Industry Canada
This product complies with RSS210 Industry Canada.
Operation is subject to the following two conditions;
(1) this device may not cause interference, and
(2)
this device must accept any interference, including inter-
ference that may cause undesired operation of the device.
30-Ca-1-1
<Only for model with wireless LAN>
This product (local network devices) for the band 5150-5250
MHz is only indoor usage to reduce potential for harmful
interference to co-channel Mobile Satellite systems.
High power radars are allocated as primary users (meaning they
have priority) of 5250-5350 MHz and 5650-5850 MHz and these
radars could cause interference and/or damage to LELAN devices.
30-Ca-2-1
This device has been designed to operate with an anten-
na having a maximum gain of 2.15 dBi. Antenna having a
higher gain is strictly prohibited per regulations of Industry
Canada. The Required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (EIRP) is not more
than that required for successful communication. 25-Ca-1-1
<Only for model with Bluetooth>
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada. 7-M-1
Models for Europe
<Only for model with a “CE” mark on the bottom of the computer>
Declaration of Conformity (DoC)
“Hereby, we declare that this Personal Computer is in compliance with the essential requirements
and other relevant provisions of the Directive 1999/5/EC.”
Hint:
If you want to get a copy of the original DoC of our products which relates to the R&TTE, please con-
tact our web address: http://www.doc.panasonic.de
Contact:
Panasonic Services Europe
A Division of Panasonic Marketing Europe GmbH
Panasonic Testing Centre
Network connection.
The terminal equipment is intended for connection to the following public network;
In all the countries of European Economical Area;
- Public Switched Telephony Networks
Technical Features.
The terminal equipment includes the following features;
- DTMF dialing
- Maximum bitrate receiving mode: 56 kbit/s
- Maximum bitrate sending mode: 33.6 kbit/s
This product is designed to interwork with the Public Switched Telecommunication Networks in UK, Ireland, Nether-
lands, Sweden, Denmark, Finland, Switzerland, Luxembourg, Belgium, France, Germany, Spain, Portugal, Iceland,
Greece, Italy, Norway and Austria. 18-E-1
Compliance Notice - CE Mark
This equipment is in conformance with the requirements of the European Council Directive listed below:
73/23/EEC Low Voltage Directive with amendment 93/68/EEC
89/336/EEC EMC Directive with amendments 92/31/EEC and 93/68/EEC
1999/5/EC R&TTE
21-E-1
This manual contains supplementary instructions regarding the use of the computer. It explains the cases where the operation of the
computer differs from that in the Operating Instructions.
Your computer is equipped with Wireless LAN enabling you to communicate using radio frequencies.
Supplementary Instructions
for Wireless LAN
FCC Radio Frequency Interference Requirements
This product is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range.
FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference
to co-channel Mobile Satellite systems.
High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can
cause interference with and /or damage this product.
Specifications
Data transfer rates
Standards supported
Transmission method
Wireless channels used
RF frequency band
IEEE802.11a: 54/48/36/24/18/12/9/6Mbps (automatically switched)
IEEE802.11g: 54/48/36/24/18/12/9/6Mbps (automatically switched)
IEEE802.11b: 11/5.5/2/1 Mbps
IEEE802.11a/IEEE802.11g/IEEE802.11b
OFDM system, DSSS system
IEEE802.11a: Channels 36 to 64, 149 to 165
IEEE802.11b/IEEE802.11g: Channels 1 to 11
IEEE802.11a: 5.18~5.32GHz, 5.745~5.825GHz
IEEE802.11g/IEEE802.11b: 2412~2462MHz
1
Contents
Precautions ...............................................................................2
Names and Functions of Parts .................................................4
Supplementary Instructions
for HSDPA/UTMS Modem
Model No. CF-19 Series
Personal Computer
1
Car Mounter
Auto monter
䔺䕑῵ഫ
カーマウンター
ENGLISH OPERATING INSTRUCTIONS .......................2
DEUTSCH BEDIENUNGSANLEITUNG ...........................5
FRANÇAIS INSTRUCTIONS D’UTILISATION ..................9
ㅔԧЁ᭛ Փ⫼䇈ᯢк ....................................................13
ⅺ㋤ʑᄽ ᪡԰ᣛफ ........................................................16
䚐ạ㛨 㦤㣅G㫴㾜㉐ ................................................... 19
日本語 取扱説明書 ....................................................22
Model No. CF-WEB184 Series
ൟোCF-WEB184 ㋏߫
WEB184.indd 1WEB184.indd 1 2006/11/01 9:27:312006/11/01 9:27:31
3
Description of Parts
A. Security lock
LOCK
You can connect a Kensington
cable. Refer to the instruction
manual of the cable.
B. LAN port
C. USB port
D. Serial port
E. External display port
F. Headphone jack
G. Microphone jack
H. DC-IN jack DC IN 16V
I. Key insertion slot
J. Dock indicator
DOCKED
K. Latch
L. Lever
DOCK UNDOCK
The lever is locked when the
key is inserted and turned
toward side. When the
computer has been installed,
be absolutely sure to lock
this lever by turning the key
toward side.
NOTE
The lock was turned to side in the default setting.
When installing the computer, confi rm that the lever is slid toward
the UNDOCK side.
Bottom Side
A. External wireless WAN
antenna port WWAN (optional)
B. External wireless LAN/GPS
antenna port WLAN/GPS
(optional)
WEB184.indd 3WEB184.indd 3 2006/11/01 9:27:332006/11/01 9:27:33
4
Installation holes are provided in the areas indicated by the arrows in the fi gure above.
Precautions for Installing the Car Mounter
Do Not Install This Product in
Unstable State
If balance of the computer is lost, it
may fall over or drop, resulting in an
injury.
Do Not Install This Product
Wherever There is a Lot of Water,
Moisture, Steam, Dust, Oily Vapors,
etc.
Otherwise, possibly resulting in fi re or
electric shock.
Dimensional Drawing
Bottom Side
The ends of the screws are protrud-
ing. Take care to protect your fi ngers,
etc. from their sharp points when in-
stalling the Car Mounter.
CAUTION
Install the Car Mounter horizontally.
WEB184.indd 4WEB184.indd 4 2006/11/01 9:27:332006/11/01 9:27:33

Navigation menu