Panasonic of North America 9TGCF-19B Toughbook CF-19 PC with WWAN, WLAN and Bluetooth User Manual CF 19CTQZZBM indb

Panasonic Corporation of North America Toughbook CF-19 PC with WWAN, WLAN and Bluetooth CF 19CTQZZBM indb

UserManual.wiki >

Panasonic of North America >

9TGCF 19B User Manual

Users Manual

ContentsGetting StartedOPERATING INSTRUCTIONSPersonal ComputerModel No. CF-19 seriesIntroduction ................................................................. 2Read Me First ............................................................. 3Description of Parts ..................................................10First-time Operation ..................................................13Useful InformationOn-screen Manual ....................................................18Handling and Maintenance .......................................19Reinstalling Software ................................................21TroubleshootingTroubleshooting (Basic) ............................................23AppendixLIMITED USE LICENSE AGREEMENT ...................27Speciﬁ cations ...........................................................29LIMITED WARRANTY ..............................................32Please read these instructions carefully before using this product and save this manual for future use.For further information about the com-puter, you can refer to the on-screen manual.To access the on-screen manual  page 18 “On-screen Manual”Getting StartedUseful InformationTroubleshootingAppendixCF-19CTQZZBM.indb 1 2008/11/10 10:16:09

3Getting StartedRead Me FirstModels for U.S.A.Federal Communications Commission Radio Fre-quency Interference StatementNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal-lation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer-ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dif-ferent from that to which the receiver is connected. Consult the Panasonic Service Center or an experi-enced radio/TV technician for help.WarningTo assure continued compliance, use only shielded inter-face cables when connecting to a computer or peripheral. Also, any changes or modiﬁ cations not expressly ap-proved by the party responsible for compliance could void the user’s authority to operate this equipment.FCC RF Exposure Warning: This computer is provided with PC Card slot that could be used with wireless transmitter(s), which will be speciﬁ -cally recommended when they become available. Other third-party wireless transmitter(s) have not been RF exposure evaluated for use with this computer and may not comply with FCC RF exposure requirements. This computer complies with FCC radiation exposure limits set forth for an uncontrolled environment. This computer may not be co-located or operated with any other antenna or transmitter.<For computer with installed WLAN/Bluetooth> This PC with WLAN and/or Bluetooth transmitters in-stalled, has been approved for portable operation and does not require any minimum spacing be provided between antennas and all person’s body.<For computer with installed WWAN> This PC with WWAN transmitter installed, has been ap-proved for portable operation, requires LCD side panel spacers to provide minimum 1.5cm spacing between antenna located within the LCD side panel, and all per-son’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.<Optonal Car Mounter / Port Replicator> This equipment is provided with external antenna connector(s) for connection to optional Car Mounter or Port Replicator for mobile external mounted antenna(s). External antenna(s) must be professionally installed and cannot exceed recommended maximum antenna gain as described in individual provided supplement instructions for wireless transmitters. Also, user must maintain mini-mum 20 cm spacing between external antenna(s) and all person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.<Only for model with wireless LAN>This product is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this product.25-M-W-1This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired op-eration.Responsible Party: Panasonic Corporation of North America One Panasonic Way Secaucus, NJ 07094 Tel No:1-800-LAPTOP5 (1-800-527-8675)6-M-1FCC Regulation Notice for modemThis equipment contains a FCC approved modem.1. This equipment complies with CFR47 Part 68 rules. On the computer is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If re-quired, this information must be provided to the tele-phone company.2. An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. See Installation Instruc-tions for details.3. The REN is used to determine the quantity of devices which may be connected to the telephone line. Ex-cessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all area, the sum of RENs should not ex-ceed ﬁ ve (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.4. If your telephone equipment cause harm to the tele-phone network, the telephone company will notify you in advice that temporary discontinuance of service may be required. But if advice notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to ﬁ le a complaint with the FCC if you believe it is neces-sary.5. The telephone company may take changes in its facili-ties, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modiﬁ cations to maintain uninterrupted service.CF-19CTQZZBM.indb 3 2008/11/10 10:16:13

4Getting StartedRead Me First6. If trouble is experienced with this equipment, for repair or warranty information, please contact Panasonic Corporation of North America at DIAL TOLL FREE 1-800-LAPTOP5 (1-800-527-8675). If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equip-ment until the problem is resolved.7. There are no user serviceable parts contained in this equipment.8. This equipment may not be used on coin service pro-vided by the telephone company. Connection to party lines is subject to state tariffs.9. The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the ﬁ rst page of the transmission, the date and time it is sent and an identiﬁ cation of the business or other entry, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. In order to program this information into your fax software, you should refer to the manual of the Fax software being used.10. According to the FCC’s electrical safety advisory, we recommend that you may install an AC surge arrestor in the AC outlet to which this equipment is connected. Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources and that this is a major nationwide problem. “Caution : To reduce the risk of ﬁ re, use only No.26 AWG or larger telecommunication line cord.” “ATTENTION : Pour réduire le risque d’incendie, utiliser uniquement des conducteurs de télécommunications 26 AWG ou de section supérieure.” 16-M-1Models for CanadaIndustry Canada (IC) Notice for modemThis equipment contains an Industry Canada approved modem unit.The Industry Canada label is afﬁ xed on the modem unit.EQUIPMENT ATTACHEMENT LIMITATIONS“NOTICE: The Industry Canada label identiﬁ es certiﬁ ed equipment. This certiﬁ cation means that the equipment meets telecommunications network protective, opera-tional and safety requirements as prescribed in the ap-propriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connec-tion. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.Repairs to certiﬁ ed equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.Users should ensure for their own protection that the elec-trical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be par-ticularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection author-ity, or electrician, as appropriate.”“NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maxi-mum number of terminals allowed to be connected to a tele-phone interface. The termination on an interface may consist of any combination of devices subject only to the require-ment that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.”REN: See bottom of the computerRESTRICTIONS CONCERNANT LE RACCORDEMENT DE MATÉRIEL“AVIS: L’étiquette d’Industrie Canada identiﬁ e le matériel homologué. Cette étiquette certiﬁ e que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’entreprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de raccordement.L’abonné ne doit pas oublier qu’il est possible que la con-formité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations.Les réparations de matériel homologué doivent être coordonnées par un représentant désigné par le fournis-seur.L’entreprise de télécommunications peut demander à l’utilisateur de débrancher un appareil à la suite de répa-rations ou de modiﬁ cations effectuées par l’utilisateur ou à cause de mauvais fonctionnement.Pour sa propre protection, l’utilisateur doit s’assurer que tous les ﬁ ls de mise à la terre de la source d’énergie électrique, des lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales. Avertissement: L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à un service d’inspection des installations élec-triques, ou à un électricien, selon le cas.”“AVIS: L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condi-tion que la somme d’indices d’équivalence de la sonnerie de touts les dispositifs n’excède pas 5.”IES: Voir sous le fond de l’ordinateur 17-Ca-1CF-19CTQZZBM.indb 4 2008/11/10 10:16:13

5Getting StartedCanadian ICES-003This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. 7-M-2<Only for model with wireless LAN/Bluetooth>Industry CanadaThis product complies with RSS310 Industry Canada.Operation is subject to the following two conditions;(1) this device may not cause interference, and(2) this device must accept any interference, including inter-ference that may cause undesired operation of the device.30-Ca-1-1<Only for model with wireless LAN>This product (local network devices) for the band 5150-5250 MHz is only indoor usage to reduce potential for harm-ful interference to co-channel Mobile Satellite systems.High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LELAN devices.30-Ca-2-1This device has been designed to operate with the Ra-diall/Larsen whip antenna, type NMO5E2400BKTNC WLAN antenna having a maximum gain of 5dB. A WLAN Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The Required antenna impedance is 50 ohms.To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication.Models for Europe<Only for model with a “CE” mark on the bottom of the computer>Declaration of Conformity (DoC)“Hereby, we declare that this Personal Computer is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC.”Hint:If you want to get a copy of the original DoC of our products which relates to the R&TTE, please con-tact our web address: http://www.doc.panasonic.deContact and Pursuant to at the directive 2004/108/EC, article 9(2)Panasonic Testing CentrePanasonic Service Europe, a division ofPanasonic Marketing Europe GmbHWinsbergring 15, 22525 Hamburg, GermanyNetwork connection.The terminal equipment is intended for connection to the following public network;In all the countries of European Economical Area;- Public Switched Telephony NetworksTechnical Features.The terminal equipment includes the following features;- DTMF dialing- Maximum bitrate receiving mode: 56 kbit/s- Maximum bitrate sending mode: 33.6 kbit/sThis product is designed to interwork with the Public Switched Telecommunication Networks in UK, Ireland, Nether-lands, Sweden, Denmark, Finland, Switzerland, Luxembourg, Belgium, France, Germany, Spain, Portugal, Iceland, Greece, Italy, Norway and Austria. 18-E-2When using your telephone equipment, basic safety precau-tions should always be followed to reduce the risk of ﬁ re, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.3. Do not use the telephone to report a gas leak in the vicinity of the leak.4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a ﬁ re. They may explode. Check with local codes for possible special disposal instructions.SAVE THESE INSTRUCTIONS19-E-1Certaines mesures de sécurité doivent être prises pen-dant l’utilisation de matérial téléphonique aﬁ n de réduire les risques d’incendie, de choc électrique et de blessures. En voici quelquesunes:1. Ne pas utiliser l’appareil près de l’eau, p.ex., près d’une baignoire, d’un lavabo, d’un évier de cuisine, d’un bac à laver, dans un sous-sol humide ou près d’une piscine.2. Éviter d’utiliser le téléphone (sauf s’il s’agit d’un appareil sans ﬁ l) pendant un orage électrique. Ceci peut présenter un risque de choc électrique causé par la foudre.3. Ne pas utiliser l’appareil téléphonique pour signaler une fuite de gaz s’il est situé près de la fuite.4. Utiliser seulement le cordon d’alimentation et le type de piles indiqués dans ce manual. Ne pas jeter les piles dans le feu: elles peuvent exploser. Se conformer aux règlements pertinents quant à l’élimination des piles.CONSERVER CES INSTRUCTIONS19-F-1Important Safety Instructions / Importantes Mesures De SécuritéCF-19CTQZZBM.indb 5 2008/11/10 10:16:13

6Getting StartedRead Me FirstInformation to the User<Only for model with wireless LAN/Bluetooth>This product and your HealthThis product, like other radio devices, emits radio fre-quency electromagnetic energy. The level of energy emitted by this product however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.Because this product operates within the guidelines found in radio frequency safety standards and recommenda-tions, we believe this product is safe for use by consum-ers. These standards and recommendations reﬂ ect the consensus of the scientiﬁ c community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.In some situations or environments, the use of this prod-uct may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include: Using this product on board of airplanes, or In any other environment where the risk of interference to other devices or services is perceived or identiﬁ ed as harmful.If you are uncertain of the policy that applies on the use of wireless devices in a speciﬁ c organization or environ-ment (e.g. airports), you are encouraged to ask for autho-rization to use this product prior to turning on the product.Regulatory InformationWe are not responsible for any radio or television interfer-ence caused by unauthorized modiﬁ cation of this product. The correction of interference caused by such unauthor-ized modiﬁ cation will be the responsibility of the user. We and its authorized resellers or distributors are not liable for damage or violation of government regulations that may arise from failing to comply with these guidelines.26-M-1Safety Precautions<Only for model with wireless WAN>The following safety precautions must be observed during all phases of the operation, usage, service or repair of any Personal Computer or Handheld Computer incorporating wireless WAN modem. Manufacturers of the cellular termi-nal are advised to convey the following safety information to users and operating personnel and to incorporate these guidelines into all manuals supplied with the product. Failure to comply with these precautions violates safety stan-dards of design, manufacture and intended use of the product. Panasonic assumes no liability for customer failure to comply with these precautions*1. When in a hospital or other health care facility, observe the restrictions on the use of mobiles. Switch Per-sonal Computer or Handheld Computer incorporating wireless WAN modem off, if instructed to do so by the guidelines posted in sensitive areas. Medical equipment may be sensitive to RF energy. The operation of cardiac pacemakers, other implanted medical equipment and hearing aids can be affected by interference from Personal Computer or Handheld Computer incorporating wireless WAN modem placed close to the device. If in doubt about potential danger, contact the physician or the manufacturer of the de-vice to verify that the equipment is properly shielded. Pacemaker patients are advised to keep their Personal Computer or Handheld Computer incorporating wireless WAN modem away from the pacemaker, while it is on. Switch off Personal Computer or Handheld Computer incorporating wireless WAN modem before boarding an aircraft. Make sure it cannot be switched on inadvertently. The operation of wireless appliances in an air-craft is forbidden to prevent interference with communications systems. Failure to observe these instructions may lead to the suspension or denial of cellular services to the offender, legal action, or both. Do not operate Personal Computer or Handheld Computer incorporating wireless WAN modem in the pres-ence of ﬂ ammable gases or fumes. Switch off the cellular terminal when you are near petrol stations, fuel depots, chemical plants or where blasting operations are in progress. Operation of any electrical equipment in potentially explosive atmospheres can constitute a safety hazard. Your Personal Computer or Handheld Computer incorporating wireless WAN modem receives and trans-mits radio frequency energy while switched on. Remember that interference can occur if it is used close to TV sets, radios, computers or inadequately shielded equipment. Follow any special regulations and always switch off Personal Computer or Handheld Computer incorporating wireless WAN modem wherever forbid-den, or when you suspect that it may cause interference or danger. Road safety comes ﬁ rst! Do not use a Personal Computer or Handheld Computer incorporating wireless WAN modem while driving a vehicle. Do not place the computer with wireless WAN modem in an area where it could cause personal injury to the driver or passengers. It is recommended to stow the unit in the boot or secure stowage area while driving. Do not place the computer with wireless WAN modem in an area over an air bag or in the vicinity where an air bag may deploy. CF-19CTQZZBM.indb 6 2008/11/10 10:16:13

7Getting StartedLithium Battery / Pile au lithiumLithium Battery!This computer contains a lithium battery to enable the date, time, and other data to be stored. The battery should only be exchanged by authorized service person-nel.Warning!A risk of explosion from incorrect installation or misappli-cation may possibly occur.15-E-1Pile au lithium!Le micro-ordinateur renferme une pile au lithium qui permet de sauvegarder certaines données, notamment la date et l’heure. La pile ne doit être remplacée que par un technicien qualiﬁ é.Danger ! Risque d’explosion en cas de non respect de cette mise en garde!15-F-1For Used in Motor Vehicle /Pour L’utilisation Dans Un Véhicule MotoriséWarning: Notebook Computer may be installed in a mo-tor vehicle and visible to the driver only if used to support vehicle related functions such as vehicle information, system control, rear or side observation and navigation. If used for entertainment purpose, such as television reception or video play, it must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. Check with individual state/provincial laws to determine lawful use of this product while operating within a motor vehicle.Information on Disposal in other Countries outside the European UnionThese symbols are only valid in the European Union.If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.53-M-1Avertissement : L’ordinateur bloc-notes peut être installé dans un véhicule motorisé et dans le champ de vision du conducteur uniquement en tant que dispositif d’aide aux fonctions du véhicule, comme par exemple pour fournir des informations sur le véhicule, comme dispositif de contrôle de système, pour l’observation à l’arrière ou sur les côtés du véhicule, ainsi que pour fournir de l’informa-tion routière. Pour toute utilisation à ﬁ n de divertissement, comme par exemple pour regarder la télévision ou jouer à des jeux vidéo, il doit être installé à l’arrière du siège du conducteur, en un emplacement où il ne sera pas visible, ni directement ni indirectement, pour le conducteur du véhicule motorisé. Vériﬁ ez les lois fédérales et nationales qui régissent l’utilisation légale de cet appareil à l’intérieur d’un véhicule motorisé.35-M-1 Air bags inﬂ ate with great force and if the computer with wireless WAN modem is placed in the air bag de-ployment area may be propelled with great force and cause serious injury to occupants of the vehicle. IMPORTANT!Personal Computer or Handheld Computer incorporating wireless WAN modem operate using radio signals and cellular networks cannot be guaranteed to connect in all conditions. Therefore, you should never rely solely upon any wireless device for essential communications, for example emergency calls.Remember, in order to make or receive calls, Personal Computer or Handheld Computer incorporating wire-less WAN modem must be switched on and in a service area with adequate cellular signal strength.Some networks do not allow for emergency calls if certain network services or phone features are in use (e.g. lock functions, ﬁ xed dialing etc.). You may need to deactivate those features before you can make an emer-gency call.Some networks require that a valid SIM card be properly inserted in Personal Computer or Handheld Com-puter incorporating wireless WAN modem.27-1-2*1 In locations where the use of wireless devices is prohibited, please turn your Wireless Switch off (CF-74 Series), or check to make sure that your Wireless Ready Indicator is off (CF-52 Series). Please note that in some cases, wireless devices may be operating even in Sleep/Standby modes.CF-19CTQZZBM.indb 7 2008/11/10 10:16:13

8Getting StartedTHIS PRODUCT IS NOT INTENDED FOR USE AS, OR AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS, AIR TRAF-FIC CONTROL EQUIPMENT/SYSTEMS, OR AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS*1. PANASONIC WILL NOT BE RESPONSIBLE FOR ANY LIABILITY RESULT-ING FROM THE USE OF THIS PRODUCT ARISING OUT OF THE FOREGOING USES. *1 AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include Class2 Electrical Flight Bag (EFB) Systems and Class1 EFB Systems when used during critical phases of ﬂ ight (e.g., during take-off and landing) and/or mounted on to the aircraft. Class1 EFB Systems and 2 EFB Systems are deﬁ ned by FAA: AC (Advisory Circular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaﬂ ets) No.36.Panasonic cannot guarantee any speciﬁ cations, technolo-gies, reliability, safety (e.g. Flammability/Smoke/Toxic-ity/Radio Frequency Emission, etc) requirements related to aviation standards that exceed the speciﬁ cations of our COTS (Commercial-Off-The-Shelf) products. 39-E-1This computer is not intended for use in medical equipment including life-support systems, air trafﬁ c control systems, or other equipment, devices or systems that are involved with ensuring human life or safety. Panasonic cannot be held re-sponsible in any way for any damages or loss resulting from the use of this unit in these types of equipment, devices or systems, etc.The CF-19 was developed based on thorough research into the real-world portable computing environments. Exhaustive pursuit of usability and reliability under harsh conditions led to innovations such has the magnesium alloy exterior, vibra-tion damped hard disk drive and ﬂ oppy disk drive, ﬂ exible internal connections. The CF-19’s outstanding engineering has been tested using the strict MIL-STD- 810F (for vibration and shock) and IP (for dust and water) based procedures.As with any portable computer device precautions should be taken to avoid any damage. The following usage and han-dling procedures are recommended. Before putting the computer away, be sure to wipe off any moisture.If a Malfunction Occurs, Immediately Unplug the AC Plug and the Battery Pack This product is damaged Foreign object inside this product Smoke emitted Unusual smell emitted Unusually hotContinuing to use this product while any of the above condi-tions are present may result in ﬁ re or electric shock. If a malfunction occurs, immediately turn the power off and unplug the AC plug, and then remove the battery pack. Then, contact your technical support ofﬁ ce.Do Not Touch This Product and Cable When It Starts ThunderingElectric shock may result.Do Not Connect the AC Adaptor to a Power Source Other Than a Standard Household AC OutletOtherwise, a ﬁ re due to overheating may result. Connecting to a DC/AC converter (inverter) may damage the AC adap-tor. On an airplane, only connect the AC adaptor/charger to an AC outlet speciﬁ cally approved for such use.Do Not Do Anything That May Damage the AC Cord, the AC Plug, or the AC AdaptorDo not damage or modify the cord, place it near hot tools, bend, twist, or pull it forcefully, place heavy objects on it, or bundle it tightly.Continuing to use a damaged cord may result in ﬁ re, short circuit, or electric shock.Do Not Pull or Insert the AC Plug If Your Hands Are WetElectric shock may result.Clean Dust and Other Debris of the AC Plug RegularlyIf dust or other debris accumulates on the plug, humidity, etc. may cause a defect in the insulation, which may result in a ﬁ re. Pull the plug, and wipe it with a dry cloth.Pull the plug if the computer is not being used for a long period of time.Insert the AC Plug CompletelyIf the plug is not inserted completely, ﬁ re due to overheating or electric shock may result. Do not use a damaged plug or loose AC outlet.Close the Connector Cover Tightly When Using This Product Where Is a Lot of Water, Moisture, Steam, Dust, Oily Vapors, etc.The entry of foreign matter may cause a ﬁ re or electric shocks. If foreign matter has found its way inside, immediately turn the power off and unplug the AC cord, and then remove the battery pack. Then contact your technical support of-ﬁ ce.Do Not Disassemble This ProductThere are high-voltage areas inside which may give you an electric shock if you should touch them. Do not touch the pins and circuit boards inside, and do not allow foreign mat-ter to enter inside.Also, remodeling or disassembly may cause a ﬁ re.Keep SD Memory Cards Away from Infants and Small ChildrenAccidental swallowing will result in bodily injury.In the event of accidental swallowing, see a doctor immedi-ately.Do Not Place This Product on Unstable SurfaceIf balance is lost, this product may fall over or drop, resulting in an injury.Avoid StackingIf balance is lost, this product may fall over or drop, resulting in an injury.Do Not Leave This Product in High Temperature Envi-ronment for a Long Period of TimeLeaving this product where it will be exposed to extremely high temperatures such as in a sun-heated car or in direct sunlight may deform the cabinet and/or cause trouble in the internal parts. Continued use in such a resulting condition may lead to short-circuiting or insulation defects, etc. which may in turn lead to a ﬁ re or electric shocks.Hold the Plug When Unplugging the AC PlugPulling on the cord may damage the cord, resulting in a ﬁ re or electric shock.Do Not Move This Product While the AC Plug Is Con-nectedThe AC cord may be damaged, resulting in ﬁ re or electric shock. If the AC cord is damaged, unplug the AC plug immedi-ately.Use Only the Speciﬁ ed AC Adaptor With This ProductUsing an AC adaptor other than the one supplied (attached to your product or supplied by Panasonic) may result in a ﬁ re.Do Not Subject the AC Adaptor to Any Strong ImpactUsing the AC adaptor after a strong impact such as being dropped may result in electric shock, short circuit, or ﬁ re.Take a Break of 10-15 Minutes Every HourUsing this product for long periods of time may have detri-mental health effects on the eyes or hands.PrecautionsRead Me FirstCF-19CTQZZBM.indb 8 2008/11/10 10:16:13

9Getting StartedDo Not Turn the Volume Up to Loud When Using Head-phonesListening at high volumes that overstimulate the ear for long periods of time may result in loss of hearing.Use the Modem with a Regular Telephone LineConnection to an internal phone line (on-premise switches) of a company or business ofﬁ ce, etc. or to a digital public phone or use in a country or area not supported by the com-puter may result in a ﬁ re or electric shocks.Do Not Connect a Telephone Line, or a Network Cable Other Than the One Speciﬁ ed, into the LAN PortIf the LAN port is connected to a network such as the ones listed below, a ﬁ re or electric shock may result. Networks other than 1000BASE-T, 100BASE-TX, or 10BASE-T Phone lines (IP Phone, Telephone lines, internal phone lines (on-premise switches), digital public phones, etc.)Precautions (Battery Pack)Do Not Use with Any Other ProductThe battery pack is rechargeable and was intended for the speciﬁ ed product. If it is used with a product other than the one for which it was designed, electrolyte leakage, genera-tion of heat, ignition or rupture may result.Do Not Charge the Battery Using Methods Other Than Those Speciﬁ edIf the battery is not charged using one of the speciﬁ ed methods, electrolyte leakage, generation of heat, ignition or rupture may result.Do Not Throw the Battery Pack into a Fire or Expose It to Excessive HeatGeneration of heat, ignition or rupture may result.Avoid Extreme Heat (Near the Fire, in Direct Sunlight, for Example)Electrolyte leakage, generation of heat, ignition or rupture may result.Do Not Insert Sharp Objects into the Battery Pack, Ex-pose It to Bumps or Shocks, Disassemble, or Modify ItElectrolyte leakage, generation of heat, ignition or rupture may result. If this product is subjected to a strong impact, stop using it immediately.Do Not Short the Positive (+) and Negative (-) ContactsGeneration of heat, ignition or rupture may result. Do not place the battery pack together with articles such as necklaces or hairpins when carrying or storing.Do Not Use This Product with a Battery Pack Other Than the One Speciﬁ edUse only the speciﬁ ed battery pack (CF-VZSU48U) with your product. Use of battery packs other than those manufactured and supplied by Panasonic may present a safety hazard (generation of heat, ignition or rupture).When the battery pack has become degraded, replace it with a new oneContinued use of a degraded battery pack may generate high levels of heat, cause a ﬁ re to start and cause the pack to burst or explode. Do not touch the terminals on the battery pack. The bat-tery pack may no longer function properly if the contacts are dirty or damaged. Do not expose the battery pack to water, or allow it to become wet. If the battery pack will not be used for a long period of time (a month or more), charge or discharge (use) the battery pack until the remaining battery level becomes 30% to 40% and store it in a cool, dry place. This computer prevents overcharging of the battery by recharging only when the remaining power is less than approx. 95% of capacity.Do Not Use with Exposing the Skin to This Product for a Long Period of TimeUsing this product with exposing the skin to the heat source of this product or AC adaptor for a long period of time can cause a low-temperature burn. Do not place the computer near a television or radio re-ceiver. Keep the computer away from magnets. Data stored on the hard disk may be lost. The battery pack is not charged when the computer is ﬁ rst purchased. Be sure to charge it before using it for the ﬁ rst time. When the AC adaptor is connected to the computer, charging begins automatically. Should the battery leak and the ﬂ uid get into your eyes, do not rub your eyes. Immediately ﬂ ush your eyes with clear water and see a doctor for medical treatment as soon as possible. NOTE  The battery pack may become warm during recharg-ing or normal use. This is completely normal. Recharging will not commence if internal temperature of the battery pack is outside of the allowable temper-ature range (0 °C to 50 °C {32°F to 122 °F}). ( Reference Manual “Battery Power”) Once the allowable range requirement is satisﬁ ed, charging begins automatically. Note that the recharging time varies based on the usage conditions. (Recharging takes longer than usual when the temperature is 10 °C {50 °F} or below.) If the temperature is low, the operating time is short-ened. Only use the computer within the allowable temperature range. This computer has a high temperature mode function that prevents the degradation of the battery in high temperature environments. ( Reference Manual “Battery Power”) A level corresponding to a 100% charge for high temperature mode is approximately equivalent to an 80% charge level for normal tempera-ture mode. The battery pack is a consumable item. If the amount of time the computer can be run by using a particular battery pack becomes dramatically shorter and re-peated recharging does not restore its performance, the battery pack should be replaced with a new one. When transporting a spare battery inside a package, briefcase, etc., it is recommended that it be placed in a plastic bag so that its contacts are protected. Always power off the computer when it is not in use. Leaving the computer on when the AC adaptor is not connected will exhaust the remaining battery capacity.CF-19CTQZZBM.indb 9 2008/11/10 10:16:13

10Getting StartedDescription of PartsA: Wireless LAN Antenna <Only for model with wireless LAN> Reference Manual “Wireless LAN”B: Stylus/Digitizer pen HolderC: Touch PadD: LED Indicator : Wireless readyThis indicator lights when Wireless LAN, Blue-tooth, and/or Wireless WAN are connected and ready. It does not necessarily indicate the On/Off condition of the wireless connection. Reference Manual “Disabling/Enabling Wireless Communication” : Wireless WAN status<Only for model with wireless WAN> Refer to the instruction manual of the wireless device. : Caps lock : Numeric key (NumLk) : Scroll lock (ScrLk) : Hard disk drive statusE: Tablet Buttons Reference Manual “Tablet Buttons”F: LCD <Only for model with touchscreen>  Reference Manual “Touchscreen” <Only for model with dual touch>  Reference Manual “Dual Touch”G: Bluetooth Antenna <Only for model with Bluetooth> Reference Manual “Bluetooth”H: Display Release Latch page 12 “Switching to the Tablet mode” I: Speaker Reference Manual “Key Combinations”J: Function Key Reference Manual “Key Combinations”K: KeyboardL: Hard Disk Drive Reference Manual “Hard Disk Drive”M: Battery Pack Speciﬁ ed Battery pack: CF-VZSU48N: Power SwitchO: LED Indicator : Battery status Reference Manual “Battery Power” : Power status(Off: Power off/Hibernation, Green: Power on, Blinking green: Sleep/ Standby, Blinking green rapidly: Cannot power on or resume due to low temperature.)A lithium ion battery that is recyclable powers the product you have purchased.Please call 1-800-8-BATTERY for information on how to recycle this battery.L’appareil que vous vous êtes procuré est alimenté par une batterie au lithium-ion.Pour des renseignements sur le recyclage de la batterie, veuillez composer le 1-800-8-BATTERY.48-M-1CF-19CTQZZBM.indb 10 2008/11/10 10:16:14

11Getting StartedLeft sideRear side BottomA: DC-IN JackB: USB Port Reference Manual “USB Devices”C: IEEE 1394 Interface Connector Reference Manual “IEEE 1394 Devices”D: Modem Port Reference Manual “Modem”E: LAN Port Reference Manual “LAN”F: SD Memory Card Indicator(Blinking: During access) Reference Manual “SD Memory Card”G: SD Memory Card Slot Reference Manual “SD Memory Card”H: Wireless Switch Reference Manual “Disabling/Enabling Wireless Communication”I: <For model without Smart Card Slot> PC Card Slot (PC) Reference Manual “PC Card / ExpressCard” <For model with Smart Card Slot> Smart Card Slot (SCR) Reference Manual “Smart Card”J: <For model without Smart Card Slot> ExpressCard Slot (EX) Reference Manual “PC Card / ExpressCard” <For model with Smart Card Slot> PC Card Slot (PC) Reference Manual “PC Card / ExpressCard”K: Headphone Jack You can connect headphones or ampliﬁ ed speakers. When they are connected, audio from the internal speakers is not heard.L: Microphone Jack A condenser microphone can be used. If other types of microphones are used, audio input may not be pos-sible, or malfunctions may occur as a result. When recording in stereo using a stereo microphone:Click (Start) - [Control Panel] - [Hardware and Sound] - [Sound] - [Recording] - [Microphone] - [Properties], and then add a check mark for [No Au-dio Enhancements] in [Microphone Enhancements].Click [start] - [All Programs] - [SoundMAX] - [Control Panel] and select [Microphone], and then add a check mark for [No Filtering] in [Microphone Enhancements]. When using a monaural microphone with a 2-terminal plug:Click (Start) - [Control Panel] - [Hardware and Sound] - [Sound] - [Recording] - [Microphone] - [Properties], and then add a check mark for [Voice Enhancements] in [Microphone Enhancements].Otherwise, only audio on the left track will be recorded.Click [start] - [All Programs] - [SoundMAX] - [Control Pan-el] and select [Microphone], and then add a check mark for [Voice Recording] in [Microphone Enhancements].Otherwise, only audio on the left track will be recorded.M: Security Lock A Kensington cable can be connected. For further information, read the manual that comes with the cable.N: External Display Port Reference Manual “External Display”O: Serial PortP: RAM Module Slot Reference Manual “RAM Module”Q: External Antenna ConnectorR: Expansion Bus Connector Reference Manual “Port Replicator / Car Mounter”CF-19CTQZZBM.indb 11 2008/11/10 10:16:14

12Getting StartedDescription of PartsSwitching to the Tablet modeA Lift up the display so it stands perpendicular to the body.B Slide and hold the display release latch (A), and rotate the display clockwise until it clicks.Attaching the stylus to the computerUse the tether to attach the stylus to the computer so you will not lose it. There are holes (A) to attach it. For model with dual touch, the tether and digitizer pen are already attached to the computer at purchase.Attaching the hand strap and the shoulder strapAttach the hand strap to any two of the corners (A) using the screws.You can connect the shoulder strap (B) to the hand strap.(The illustration is an example.) CAUTION  Do not use the strap to carry a heavier weight than the computer. Other-wise the strap may become loose by itself. Do not use the strap if it becomes worn or damaged.C Close as the display faces up and ﬁ x it using the latch (B). This computer contains a magnet and magnetic products at the locations circled in the illustration at right. Avoid leaving metallic object or magnetic me-dia in contact with these areas.CF-19CTQZZBM.indb 12 2008/11/10 10:16:14

13Getting Started PreparationA Check and identify the supplied accessories.If you do not ﬁ nd the described accessories, contact Panasonic Technical Support ( page 33).• AC Adaptor . . . . . 1Model No: CF-AA1633A• AC Cord . . . . . . . 1 • Battery Pack . . . 1Model No: CF-VZSU48<Only for model with touchscreen>• Stylus . . . . . . . . . . . . . . . . . . . 1Model No: CF-VNP003U<Only for model with dual touch>• Digitizer pen . . . . . . . . . . . . . . 1Model No: CF-VNP012U• Tether . . . . . . . . . 1 • Shoulder strap . . 1 • Soft Cloth . . . . . . 1• Operating Instructions (This book) . . . . . . . . . . . . . . . . . . . . . . . . 1• Product Recovery DVD-ROM Windows Vista® Business . . . . . . 1• Product Recovery DVD-ROM Windows® XP Tablet or Windows® XP Professional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1• Windows® Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 For model with dual touch, the tether and digitizer pen are already attached to the computer at purchase.B Read the LIMITED USE LICENSE AGREEMENT before breaking the seal on the computer’s packaging ( page 27).1 Inserting the Battery PackA Slide the latch (A) to the right to unlock the cover.B Slide the latch (A) down, and open the cover.C Insert the battery pack until it securely ﬁ ts the connector.D Close the cover until it clicks.E Slide the latch (B) to the left to lock the cover. CAUTION  Make sure the latch is securely locked. Otherwise the battery pack may fall when you carry the computer. Do not touch the terminals of the battery pack and the computer. Doing so can make the terminals dirty or damaged, and may cause malfunction of the battery pack and the computer. NOTE  Note that the computer consumes electricity even when the computer power is off. If the battery pack is fully charged, the battery will fully discharge in the fol-lowing period of time:• When power is off: Approx. 7 weeks*1 *2• In sleep ( )/standby ( ): Approx. 2 days*1 *2• In hibernation: Approx. 3 days*1 *2*1 If “Wake Up from wired LAN” is disabled, the period of time in sleep will become slightly longer, and the period of time in hibernation will become about the same as during power-off. *2 If “Wake Up from wireless LAN” is enabled, the period of time in sleep will become shorter, and the period of time in hibernation will become about the same as during power-off.  When the DC plug is not connected to the computer, disconnect the AC cord from your AC wall outlet. Power is consumed simply by having the AC adaptor plugged into an electrical outlet.Power consumption in each mode is as follows. (When AC adaptor is connected)• When the screen is off: Approx. 11 W • In sleep ( )/standby ( ): Approx. 2.2 W• The battery pack is fully charged (or not being charged) and the computer is off: Approx. 0.9 WFirst-time OperationCF-19CTQZZBM.indb 13 2008/11/10 10:16:14

14Getting StartedFirst-time Operation2 Opening the DisplayA Pull up the part (A) and release the latch.B Lift open the display.3 Connect your computer to a power outlet. The battery charging starts automatically. CAUTION  Do not disconnect the AC adaptor and do not switch the wireless switch to on until the ﬁ rst-time operation procedure is completed. When using the computer for the ﬁ rst time, do not connect any peripheral device except the battery pack and AC adaptor. Handling the AC adaptor Problems such as sudden voltage drops may arise during periods of thunder and lightning. Since this could adversely affect your computer, an uninterruptible power source (UPS) is highly recommended unless running from the battery pack alone.4 Turn on the computer.A Slide and hold the power switch (B) for approximately one second until the power indicator lights. CAUTION  Do not slide the power switch repeatedly. The computer will forcibly be turned off if you slide and hold the power switch for four seconds or longer. Once you turn off the computer, wait for ten seconds or more before you turn on the computer again. Do not perform the following operation until the hard disk drive indicator turns off. Connecting or disconnecting the AC adaptor Sliding the power switch Touching the keyboard, touch pad, tablet buttons, touchscreen (only for model with touchscreen), dual touch (only for model with dual touch) or external mouse Closing the display Turn on/off the wireless switch When the CPU temperature is high, the computer may not start up to prevent overheating of the CPU. Wait until the computer cools down, and then turn the power on again. If the computer does not power on even after cooling down, contact Panasonic Technical Support ( page 33). Any changes from the default setting of the Setup Utility must not be made until the First-time Operation is completed.5 Setup Windows.Follow the on-screen instructions. After turning on the computer, “Please wait a moment while windows pre-pares to start for the ﬁ rst time .........” appears, and then a small circle circu-lates on the screen. This will take a few minutes. During setup of Windows, use the touch pad and clicking to move the cursor and to click an item. Setup of Windows will take approximately 20 minutes. Go to the next step, conﬁ rming each message on the display.CF-19CTQZZBM.indb 14 2008/11/10 10:16:14

15Getting Started CAUTION  You cannot choose the following words for user name and password: CON, PRN, AUX, CLOCK$, NUL, COM1 to COM9, LPT1 to LPT9. You can change the user name, password, image and security setting after setup of Windows. Remember your password. If you forget the password, you cannot use the Win-dows. Creating a password reset disk beforehand is recommended. The wallpaper for the ﬁ rst logon user has already been set on “4 Setup Windows.” .When using this computer under the Sun, the screen becomes easily viewable by changing the wallpaper to the white wallpaper.A Right-click on the desktop, and click [Personalize] - [Desktop Background].B Select [Solid Colors] at [Picture Location].C Select the white wallpaper and click [OK].  When you set date/time/time zone and click [Next], the screen may not go to the next step for a few minutes. Do not touch the keyboard or touch pad, and wait until the screen changes. If “An unexpected error has occurred ...” (or a similar message) is displayed, click [OK]. This is not a malfunction. Wait until the hard disk drive indicator has turned off.6 Perform the touchscreen calibration.<Only for model with touchscreen> NOTE  At ﬁ rst, log on to Windows as an administrator, and perform this calibration. Return the rotated display to [Primary Landscape] before the touchscreen cali-bration.A Click (Start) - [Control Panel] - [Additional Options] - [Tablet Calibration].B Using the stylus, touch each of the 9 “+” target marks one by one. NOTE  Perform the following calibration for each user.A Click (Start) - [Control Panel] - [Mobile PC] - [Tablet PC Settings].B Click [Calibrate].C Using the stylus, touch each of the 4 “+” target marks one by one, and then click [OK]. Perform the calibration for the orientation to be used.A Click [start] - [All Programs] - [Fujitsu Touch Panel (USB)] - [Touch Screen Calibration Utility].B Using the stylus, touch each of the 12 “+” target marks one by one until it blinks, and then press Enter.C Press Enter.<Only for model with Dual Touch> NOTE  Perform these calibration for each user. If you cannot touch the desired position, perform Digitizer Calibration again and restart the computer.A Run [Tablet PC Settings]. Click (Start) - [Control Panel] - [Mobile PC] - [Tablet PC Settings].B Click [Calibrate].C Using the digitizer pen, touch each of the 4 “+” target marks one by one, and then click [OK]. Perform the calibration for the orientation to be used.CF-19CTQZZBM.indb 15 2008/11/10 10:16:14

16Getting Started NOTE  PC Information Viewer This computer periodically records the management information including the hard disk information. The maximum data volume for each record is 1024 bytes. These information are only used for estimating the cause when the hard disk goes down by any possibility. They are never sent to outside via network nor used for any other purpose except for the purpose described the above. To disable the function, add the check mark for [Disable the automatic save function for management information history] in [Hard Disk Status] of PC Information Viewer, and click [OK]. ( Reference Manual “Checking the Computer’s Usage Status”) Precaution against Starting Up/Shutting Down Do not do the following Connecting or disconnecting the AC adaptor Sliding the power switch Touching the keyboard, touch pad, touchscreen, dual touch or external mouse Closing the display Turn on/off the wireless switch NOTE  To conserve power, the following power saving methods are set at the time of purchase. The screen automatically turns off after 15 minutes of inactivity. The computer automatically enters sleep*3( )/standby*3( ) after 20 minutes of inactiv-ity.*3 Refer to Reference Manual “Sleep or Hibernation Functions” ( )/”Standby or Hibernation Func-tions” ( ) about resuming from sleep/standby.A Run [Tablet and Pen Settings]. Double-click or click [start] - [Control Panel] - [Printers and Other Hard-ware] - [Tablet and Pen Settings].B Click [Settings] - [Calibrate].C Using the digitizer pen, touch each of the 4 “+” target marks one by one, and then click [OK]. Perform the calibration for both [Landscape] and [Portrait].7 Create a new account.Click [start] - [Control Panel] - [User Accounts] - [Create a new account]. CAUTION  Remember your password. If you forget the password, you cannot use the Win-dows operation system. Creating a password reset disk beforehand is recom-mended.First-time OperationCF-19CTQZZBM.indb 16 2008/11/10 10:16:15

17Getting Started To change the partition structureYou can shrink a part of an existing partition to create unallocated disk space, from which you can create a new parti-tion. This computer has a single partition in the default setting.A Click (Start) and right-click [Computer], then click [Manage]. A standard user needs to enter an administrator password.B Click [Disk Management].C Right-click the partition for Windows (“c” drive in the default setting), and click [Shrink Volume]. The partition size depends on the computer speciﬁ cations.D Input the size in [Enter the amount of space to shrink in MB] and click [Shrink]. You cannot input a larger number than the displayed size.E Right-click [Unallocated] (the shrunk space in the step D) and click [New Simple Volume].F Follow the on-screen instructions to make the settings, and click [Finish].Wait until formatting is completed. NOTE  You can create an additional partition using remaining unallocated space or newly creating unallocated space. To delete a partition, right-click the partition and click [Delete Volume] in the step C.CF-19CTQZZBM.indb 17 2008/11/10 10:16:15

18Useful InformationOn-screen ManualYou can access the Reference Manual and the Important Tips on the computer screen.When you access the Reference Manual and the Important Tips for the ﬁ rst time, the License Agreement of the Adobe Reader may be displayed. Read it carefully and select [Accept] to proceed. Reference Manual The Reference Manual contains the practical information to help you fully enjoy the computer’s performance.To access the Reference Manual: Double-click on the desktop. Alternatively click (Start) - [All Programs] - [Panasonic] - [On-Line Manuals] - [Reference Manual]. Click [start] - [Reference Manual]. Important Tips The Important Tips will provide you with the battery information so that you can use the battery pack in the optimum condition to obtain longer operation time.To access the Important Tips: Double-click on the desktop. Alternatively click (Start) - [All Programs] - [Panasonic] - [On-Line Manuals] - [Important Tips]. Double-click on the desktop. Alternatively click [start] - [All Programs] - [Panasonic] - [On-Line Manuals] - [Important Tips]. NOTE  When Adobe Reader update notice is displayed, we recommend you follow the on-screen procedure and update.See http://www.adobe.com/ for the latest version of Adobe Reader.CF-19CTQZZBM.indb 18 2008/11/10 10:16:15

19Useful InformationHandling and MaintenanceOperation environment Place the computer on a ﬂ at stable surface. Do not place the computer upright or turn it over. If the computer is exposed to an extremely strong impact, it may become inoperable. Temperature: Operation : 5 °C to 35 °C {41 °F to 95 °F} Storage : -20°C to 60 °C {- 4 °F to 140 °F} Humidity: Operation : 30% to 80% RH (No condensation) Storage : 30% to 90% RH (No condensation) Even within the above temperature/humidity ranges, using for a long time in an extreme environment will result in the product deterioration and will shorten the product life. Do not place the computer in the following areas, otherwise the computer may be damaged. Near electronic equipment. Image distortion or noise may occur. In extremely high or low temperature. As the computer can become hot during operation, keep it away from items that are sensitive to heat.Handling cautionsThis computer is designed to minimize shock to parts such as the LCD and the hard disk drive and equipped with a drip-proof keyboard, but no warranty is provided against any trouble caused by shock. Be extremely careful when han-dling the computer. When carrying the computer: Turn off the computer. Remove all external devices, cables, PC Cards and other protruding things. Do not drop or hit the computer against solid objects. Do not leave the display open. Do not grip the display part. Do not put anything (e.g., a piece of paper) between the display and keyboard. When you board an airplane, take the computer with you and never put it in your checked luggage. When using the computer on airplane, follow the airline’s instructions. When carrying a spare battery, put it in a plastic bag to protect its terminals. The touch pad is designed to be used with a ﬁ nger tip. Do not place any object on its surface and do not press down strongly with sharp-pointed or hard objects that may leave marks (e.g., nails, pencils and ball point pens). Avoid any harmful substances such as oil from getting into the touch pad. The cursor may not work correctly. Be careful not to get injured by dropping down or getting hit when carrying the computer. Use only the included stylus/digitizer pen to touch the screen. Do not place any object on its surface and do not press down strongly with sharp-pointed or hard objects that may leave marks (e.g., nails, pencils and ball point pens). Do not use the stylus/digitizer pen when dust or dirt (e.g., oil) is on the screen. Otherwise foreign particles on the screen/stylus/digitizer pen can scratch the screen surface or obstruct the stylus/digitizer pen operation. Use the stylus/digitizer pen only for touching the screen. Using it for any other purpose may damage the stylus/digi-tizer pen and result in scratches on the screen.<Only for model with dual touch> The dual touch uses electromagnetic induction and may not work properly near strong electrical ﬁ eld or magnetic ﬁ eld such as: Near AM radio base station or relay station antennas Near CRT displays that generate strong electromagnetic ﬁ eld noise Move the dual touch away from such locations so it will work properly. The cursor cannot follow the digitizer pen movement if you move the digitizer pen too quickly. When using peripheral devicesFollow these instructions and the Reference Manual to avoid any damage to the devices. Carefully read the instruction manuals of the peripheral devices. Use the peripheral devices conforming to the computer’s speciﬁ cations. Connect to the connectors in the correct direction. If it is hard to insert, do not try forcibly but check the connector’s shape, direction, alignment of pins, etc. If screws are included, fasten them securely. Remove the cables when you carry the computer. Do not pull the cables forcibly.CF-19CTQZZBM.indb 19 2008/11/10 10:16:15

20Useful Information Preventing your computer from unauthorized use via wireless LAN/Bluetooth/Wireless WAN<Only for model with wireless LAN/Bluetooth/Wireless WAN> Before using wireless LAN/Bluetooth/Wireless WAN, make the appropriate security settings such as data encryp-tion.MaintenanceTo clean the LCD panelUse the soft cloth included with the computer. (For further information, refer to “Suggestions About Cleaning the LCD Surface” that comes with the soft cloth.)To clean areas other than the LCD panelWipe with a soft dry cloth such as gauze. When using detergent, dip a soft cloth in water-diluted detergent and wring it thoroughly. CAUTION  Do not use benzene, thinner, or rubbing alcohol since it may adversely affect the surface causing discoloration, etc. Do not use commercially-available household cleaners and cosmetics, as they may contain components harmful to the surface. Do not apply water or detergent directly to the computer, since liquid may enter inside of the computer and cause malfunction or damage.Handling and MaintenanceCF-19CTQZZBM.indb 20 2008/11/10 10:16:15

21Useful InformationReinstalling SoftwareReinstalling software will return the computer to the default condition. When you reinstall the software, the hard disk data will be erased.Back up important data to other media or an external hard disk before reinstallation. CAUTION Do not delete the partition with recovery tools on the hard disk.The disk space in the partition is not available to store data.Preparation Prepare the following items: The Product Recovery DVD-ROM (included) Panasonic CD/DVD drive Remove all peripherals (except for the CD/DVD drive). Connect the AC adaptor and do not remove it until reinstallation is complete.1 Turn off the computer and connect the CD/DVD drive to the USB port ( page 11).2 Turn on the computer, and press F2 or Del while [Panasonic] boot screen is displayed.The Setup Utility starts up. If the password is requested, enter the Supervisor Password.3 Write down all of the contents of the Setup Utility and press F9.At the conﬁ rmation message, select [Yes] and press Enter.4 Press F10.At the conﬁ rmation message, select [Yes] and press Enter.Computer will restart.5 Press F2 or Del while [Panasonic] boot screen is displayed.The Setup Utility starts up. If the password is requested, enter the Supervisor Password.6 Set the Product Recovery DVD-ROM ( ) into the CD/DVD drive.7 Select the [Exit] menu, then select your CD/DVD drive in [Boot Override].8 Press Enter.The computer will restart. 9 Click [Reinstall Windows] and click [Next].The License Agreement screen appears.10 Click [Yes, I agree to the provisions above and wish to continue!] and click [Next].11 Select the settings and click [Next]. [Reinstall Windows to the whole Hard Disk to factory default.]You will have a single partition. [Reinstall Windows to the operating system partition.]You can keep the partition structure.12 At the conﬁ rmation message, click [YES].Reinstallation starts automatically. (It will take approximately 30 - 60 minutes.) Do not interrupt reinstallation, for example by turning off the computer. Otherwise reinstallation may become unavailable as Windows may not start up or the data may be corrupted.13 Remove the Product Recovery DVD-ROM, and then click [OK] to turn off the computer.14 Turn on the computer. If the password is requested, enter the Supervisor Password.15 Perform the “First-time Operation” ( page 14).16 Start the Setup Utility and change the settings as necessary.17 Perform Windows Update.Area usable by WindowsHard disk Partition with recovery tools(approximately 2 GB)CF-19CTQZZBM.indb 21 2008/11/10 10:16:15

22Useful Information9 Press 1 to execute [1. [Recovery]].The License Agreement screen appears. To cancel partway, press 0.10 Press 1 to select [1. Yes, I agree to the provisions above and wish to continue!].11 Select the settings. [2]: Enter the size of operating system partition and press Enter.(The size of data partition will be determined by subtracting the operating system partition size from the maximum size.) [3]: Windows will be installed in the ﬁ rst partition.(The size of the ﬁ rst partition must be 30 GB or more. If smaller, installation will not be possible.)At the conﬁ rmation message, press Y.Reinstallation starts automatically. (It will take approximately 30 - 75 minutes.) Do not interrupt reinstallation, for example by turning off the computer or pressing Ctrl + Alt + Del. Oth-erwise reinstallation may become unavailable as Windows may not start up or the data may be corrupted.12 Remove the Product Recovery DVD-ROM, and then press any key to turn off the com-puter. If additional instructions are included with the computer, be sure to read them. It may be necessary to perform additional operations during the following procedure.13 Turn on the computer. If the password is requested, enter the Supervisor Password.14 Perform the “First-time Operation” ( page 14).15 Start the Setup Utility and change the settings as necessary.Reinstalling SoftwareCF-19CTQZZBM.indb 22 2008/11/10 10:16:15

23TroubleshootingTroubleshooting (Basic)Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the “Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact Panasonic Technical Support ( page 33). You can also check the computer’s status in the PC Information Viewer ( Reference Manual “Troubleshooting (Advanced)”). Starting UpCannot start up.The power indicator or bat-tery indicator is not lit. Connect the AC adaptor. Insert a fully charged battery. Remove the battery pack and the AC adaptor, then connect them again.  If a device is connected to the USB port, disconnect the device, or set [USB Port] or [Legacy USB Support] to [Disable] in the [Advanced] menu of the Setup Utility. If a device is connected to the ExpressCard slot, disconnect the device, or set [ExpressCard Slot] to [Disable] in the [Advanced] menu of the Setup Utility. Press Fn + F8 to turn off the concealed mode.The power is turned on but “Warming up the system (up to 30 minutes)” appears. The computer is warming up before start up. Wait for the computer to start up (takes up to 30 minutes). If, “Cannot warm up the system” is displayed, the computer failed to warm up and does not start. In this case, turn off the computer, leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, and then turn on the power again.Cannot turn on the computer.The computer does not re-sume from sleep( )/standby ( ).(The power indicator blinks quickly in green.) Leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, then turn on the power again.You have forgotten the pass-word. Supervisor Password or User Password: Contact Panasonic Technical Support ( page 33). Administrator password:  If you have a password reset disk, you can reset the administrator password. Set the disk and enter any wrong password, then follow the on-screen instructions and set a new password. If you do not have a password reset disk, reinstall ( page 21) and set up Windows, and then set a new password.“Remove disks or other media. Press any key to restart” or a similar message appears. A ﬂ oppy disk is in the drive and it does not contain system startup information. Remove the ﬂ oppy disk and press any key. If a device is connected to the USB port, disconnect the device, or set [USB Port] or [Legacy USB Support] to [Disable] in the [Advanced] menu of the Setup Utility. If a device is connected to the ExpressCard slot, disconnect the device, or set [ExpressCard Slot] to [Disable] in the [Advanced] menu of the Setup Utility. If the problem persists after removing the disk, it may be a hard disk failure. Contact Panasonic Technical Support ( page 33).Windows startup and opera-tion is slow. Press F9 in the Setup Utility ( Reference Manual “Setup Utility”) to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again. (Note that the processing speed depends on the ap-plication software, so this procedure may not make Windows faster.) If you installed a resident software after purchase, turn off the residence. Disable Indexing Service in the following menu.Click [start] - [Search] - [Change preferences] - [With Indexing Service (for faster local service)].The date and time are incor-rect. Make the correct settings. Click (Start) - [Control Panel] - [Clock, Language, and Region] - [Date and Time]. Click [start] - [Control Panel] - [Date, Time, Language, and Regional Options] - [Date and Time]. If the problem persists, the internal clock battery may need to be replaced. Contact Panasonic Technical Support ( page 33). When the computer is connected to LAN, check the date and time of the server. The 2100 A.D. or later year will not be correctly recognized on this computer.[Executing Battery Recali-bration] screen appears. The Battery Recalibration was canceled before Windows was shut down last time. To start up Windows, turn off the computer by the power switch, and then turn on.CF-19CTQZZBM.indb 23 2008/11/10 10:16:15

24Troubleshooting Starting Up[Enter Password] does not appear when resuming from sleep ( )/standby ( )/hibernation. The password you have set in the Setup Utility is not requested at resuming. To use the password security at resuming, set the Windows password.A Click (Start) - [Control Panel] - [Add or remove user accounts] and select the ac-count, and set the password.B Click (Start) - [Control Panel] - [System and Maintenance] - [Require a password when the computer wakes] and add a check mark for [Require a password].A Click [start] - [Control Panel] - [User Accounts] and select the account, and set the password.B Click [start] - [Control Panel] - [Performance and Maintenance] - [Power Options] - [Advanced] and add a check mark for [Prompt for password when computer resumes from standby].Cannot resume.  An error may occur when the computer automatically enters the sleep or hibernation mode while the screensaver is active. In this case, turn off the screensaver or change the pattern of the screensaver.Other startup problems.  Press F9 in the Setup Utility ( Reference Manual “Setup Utility”) to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again. Remove all peripheral devices. Check to see if there was a disk error.A Remove all peripheral devices including an external display.B Click (Start) - [Computer] and right-click [Local Disk (C:)], and click [Properties].C Click [Tools] - [Check Now...]. A standard user needs to enter an administrator password.D Select the option in [Check disk options] and click [Start].E Click [Schedule disk check] and restart the computer.A Click [start] - [My Computer] and right-click [Local Disk(C:)], and click [Properties].B Click [Tools] - [Check Now].C Select the option in [Check disk options] and click [Start]. Start the computer in Safe Mode and check the error details. When the [Panasonic] boot screen disappears*1 at startup, press and hold F8 until the Windows Advanced Options Menu is displayed.*1 When [Password on boot] is set to [Enabled] in the [Security] menu of the Setup Utility, [Enter Password] appears after the [Panasonic] boot screen disappears. As soon as you enter the password and press Enter, press and hold F8. Entering PasswordOn the [Enter Password] screen, the password cannot be entered. The computer may be in ten-key mode. If the NumLk indicator lights, press NumLk to disable the ten-key mode, and then input.Even after entering the pass-word ( )/ Locked ( )/Type your password, is displayed again. The computer may be in ten-key mode.If the NumLk indicator lights, press NumLk to disable the ten-key mode, and then input. The computer may be in Caps Lock mode.If the Caps Lock indicator lights, press Caps Lock to disable the Caps Lock mode, and then input. Shutting downWindows does not shut down. Remove the USB device and the ExpressCard. Wait one or two minutes. It is not a malfunction.Troubleshooting (Basic)CF-19CTQZZBM.indb 24 2008/11/10 10:16:15

$25Troubleshooting DisplayNo display.  The external display is selected. Press Fn + F3 to switch the display. Wait until the display has been switched completely before pressing Fn + F3 again. When using an external display, Check the cable connection. Turn on the display. Check the settings of external display. The display is turned off by the power-saving function. To resume, do not press the direct selection keys, but press any other key like Ctrl. The computer entered sleep ( ) /standby ( ) or hiberna-tion by the power-saving function. To resume, press the power switch.The screen is dark.  The screen is darker when the AC adaptor is not connected. Press Fn + F2 and adjust the brightness. As you increase the brightness, battery consumption increases. You can separately set the brightness for when the AC adaptor is connected and when not connected. Press Fn + F8 to turn off the concealed mode.The screen is disordered.  Changing the number of display colors and resolution may affect the screen. Restart the computer. Connecting/disconnecting an external display may affect the screen. Restart the com-puter.During Simultaneous display, one of the screens becomes disordered. When using the Extended Desktop, use the same display colors for the external display as those used by the LCD. If you continue to experience problems, try changing the display.Right-click on the desktop, and click [Graphics Properties] - [Display Devices].Clicking [start] - [Control Panel] - [Other Control Panel Options] - [Intel(R) GMA Driver for Mobile] - [Display Devices]. When the [Command Prompt] is set to “Full Screen” by pressing Alt+Enter, the picture is displayed on one of the screens only. When the window display is restored by pressing Alt+Enter, the picture is displayed on both screens. Simultaneous display cannot be used until Windows startup is complete (during Setup Utility, etc.).The external display does not work normally. If the external display does not support the power saving function, it may not work nor-mally when the computer enters the power saving mode. Turn off the external display.<Only for model with GPS>The cursor cannot be con-trolled properly. Operate the following steps.A Set [GPS] to [Disable] in the [Advanced] - [Serial Port Settings] of the Setup Utility.B Press F10 and select [Yes] at the conﬁ rmation message, and press Enter.The computer will restart.C Log on to Windows as an administrator.D Click (Start) and input “c:\util\drivers\gps\GPSVista.reg” in [Start Search], and press Enter.E Click [Yes] and click [OK].The computer will restart.F Press F2 while [Panasonic] boot screen is displayed.G Set [GPS] to [Enable] in the [Advanced] - [Serial Port Settings].H Press F10 and select [Yes] at the conﬁ rmation message, and press Enter.CF-19CTQZZBM.indb 25 2008/11/10 10:16:16$

$26Troubleshooting Touch Pad / Touchscreen (only for model with touchscreen)/Dual Touch (only for model with dual touch)The cursor does not work.  When using the external mouse, connect it correctly. Restart the computer using the keyboard. Press and press  three times, and press  to select [Restart] and press Enter. Press , U, and R to select [Restart]. If the computer does not respond to keyboard commands, read “No response”( below).Cannot input using the touch pad. Set [Touch Pad] to [Enable] in the [Main] menu of the Setup Utility. The drivers for some mice may disable the touch pad. Check your mouse’s operating instructions.<Only for model with touch-screen>Cannot input using the touchscreen. Set [Touchscreen Mode] to [Auto] or [Tablet] in the [Main] menu of the Setup Utility. Set [Touchscreen Mode] to [Auto] or [Touchscreen Mode] in the [Main] menu of the Setup Utility.Cannot point the correct position using the included stylus/digitizer pen.<Only for model with touchscreen> Perform the touchscreen calibration ( page 15).<Only for model with dual touch> Perform the digitizer calibration and Touchscreen calibration ( page 15). Use the included digitizer pen. On the Windows logon screen or the Welcome screen, you may not be able to point the correct position using the included digitizer pen. Use the keyboard or the touch pad to log on. Reference ManualThe Reference Manual is not displayed. Install Adobe Reader.A Log on to Windows as an administrator. B Click (Start) and input “c:\util\reader\Setup.exe” in [Start Search] then press Enter.C Update Adobe Reader to its latest version.If your computer is connected to the internet, start up Adobe Reader and click Help] - [Check for Updates...]. B Click [start] - [Run], input [c:\util\reader\Setup.exe], then click [OK].C Update Adobe Reader to its latest version.If your computer is connected to the internet, start up Adobe Reader and click [Help] - [Check for updates now]. OthersNo response.  Press Ctrl+Shift+Esc to open Task Manager and close the software application that is not responding. An input screen (e.g., password input screen at startup) may be hidden behind another window. Press Alt+Tab to check. Slide the power switch for four seconds or longer to shut down the computer, and then slide the power switch to turn it on. If the application program does not work normally, uninstall and reinstall the program. To uninstall, click (Start) - [Control Panel] - [Uninstall a program]. click [start] - [Control Panel] - [Add or Remove Programs].Troubleshooting (Basic)CF-19CTQZZBM.indb 26 2008/11/10 10:16:16$

27AppendixLIMITED USE LICENSE AGREEMENTTHE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC® PRODUCT (“PROD-UCT”) ARE LICENSED ONLY TO THE END-USER (“YOU”), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY DEEMED TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE.Panasonic Corporation (“PC”) has developed or otherwise obtained the Programs and hereby licenses their use to you. You assume sole responsibility for the selection of the Product (including the associated Programs) to achieve your intended results, and for the installation, use and results obtained therefrom.LICENSEA. PC hereby grants you a personal, non-transferable and non-exclusive right and license to use the Programs in ac-cordance with the terms and conditions stated in this Agreement. You acknowledge that you are receiving only a LIMITED LICENSE TO USE the Programs and related documentation and that you shall obtain no title, ownership nor any other rights in or to the Programs and related documentation nor in or to the algorithms, concepts, designs and ideas represented by or incorporated in the Programs and related documentation, all of which title, ownership and rights shall remain with PC or its suppliers.B. You may use the Programs only on the single Product which was accompanied by the Programs.C. You and your employees and agents are required to protect the conﬁ dentiality of the Programs. You may not distrib-ute or otherwise make the Programs or related documentation available to any third party, by time-sharing or other-wise, without the prior written consent of PC.D. You may not copy or reproduce, or permit to be copied or reproduced, the Programs or related documentation for any purpose, except that you may make one (1) copy of the Programs for backup purposes only in support of your use of the Programs on the single Product which was accompanied by the Programs. You shall not modify, or at-tempt to modify, the Programs.E. You may transfer the Programs and license them to another party only in connection with your transfer of the single Product which was accompanied by the Programs to such other party. At the time of such a transfer, you must also transfer all copies, whether in printed or machine readable form, of every Program, and the related documentation, to the same party or destroy any such copies not so transferred.F. You may not remove any copyright, trademark or other notice or product identiﬁ cation from the Programs and you must reproduce and include any such notice or product identiﬁ cation on any copy of any Program.YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANICALLY OR ELECTRONICALLY TRACE THE PROGRAMS, OR ANY COPY THEREOF, IN WHOLE OR IN PART.YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PROGRAMS OR ANY COPY THEREOF, IN WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE.IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO ANOTHER PARTY, EXCEPT AS PER-MITTED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY TERMINATED.TERMThis license is effective only for so long as you own or lease the Product, unless earlier terminated. You may termi-nate this license at any time by destroying, at your expense, the Programs and related documentation together with all copies thereof in any form. This license will also terminate effective immediately upon occurrence of the conditions thereof set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein. Upon any such termination, you agree to destroy, at your expense, the Programs and related documentation together with all copies thereof in any form.YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT IT IS THE COMPLETE AND EXCLUSIVE STATE-MENT OF THE AGREEMENT BETWEEN US, WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT, ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MAT-TER OF THIS AGREEMENT.About Intel® software productsThe enclosed software products and documentation were developed at private expense, and are provided with “RE-STRICTED RIGHTS.” Use, duplication or disclosure by the government is subject to restrictions as set forth in FAR 52.227-14 and DFARS 252.227-7013 et. seq. or its successor. The use of this product by the government constitutes acknowledgment of Intel’s proprietary rights in the product.CF-19CTQZZBM.indb 27 2008/11/10 10:16:16

28AppendixContrat de licence d’usage limitéLe(s) logiciel(s) (les “Logiciels”) fournis avec ce produit Panasonic® (le “Produit”) sont exclusivement concédés en licence à l’utilisateur ultime (“vous”), et ils ne peuvent être utilisés que conformément aux clauses contractuelles cides-sous. En utilisant les logiciels, vous vous engagez de manière déﬁ nitive à respecter les termes, clauses et conditions des présentes.Panasonic Corporation (“PC”) a mis au point ou obtenu les Logiciels et vous en concède l’utilisation par les présentes. Vous assumez l’entière responsabilité du choix de ce Produit (y compris des Logiciels associés) pour obtenir les résul-tats escomptés, ainsi que de l’installation, de l’utilisation et des résultats obtenus.LicenceA. PC vous octroie par les présentes le droit et la licence personnels, non cessibles et non exclusifs d’utiliser les Logiciels conformément aux termes, clauses et conditions de ce contrat. Vous reconnaissez ne recevoir qu’un droit limité d’utiliser les Logiciels et la documentation les accompagnant et vous vous engagez à n’obtenir aucun droit de titre, propriété ni aucun autre droit vis-à-vis des Logiciels et de la documentation les accompagnant ni vis-à-vis des algorithmes, concepts, dessins, conﬁ gurations et idées représentés par ou incorporés dans les Logiciels et la documentation les accompagnant, dont les titres, propriété et droits resteront tous à PC ou à leurs propriétaires.B. Vous ne pouvez utiliser les Logiciels que sur le Produit unique qui est accompagné par les Logiciels.C. Vous et vos employés ou agents êtes requis de protéger la conﬁ dentialité des Logiciels. Vous ne pouvez ni dis-tribuer ni mettre les Logiciels et la documentation les accompagnant à la disposition d’un tiers, par partage de temps ou de quelque autre manière que ce soit, sans l’autorisation écrite préalable de PC.D. Vous ne pouvez ni copier ni reproduire ni permettre la copie ni la reproduction des Logiciels ni de la documenta-tion les accompagnant pour quelque ﬁ n que ce soit, à l’exception d’une (1) copie des Logiciels à des ﬁ ns de sau-vegarde uniquement pour soutenir votre utilisation des Logiciels sur le Produit unique qui est accompagné par les Logiciels. Vous ne pouvez ni modiﬁ er ni tenter de modiﬁ er les Logiciels.E. Vous ne pouvez céder les Logiciels et en octroyer la licence à une autre partie qu’en rapport avec votre cession du Produit unique qui est accompagné par les Logiciels à cette autre partie. Au moment de cette cession, vous devez céder également toutes les copies, que ce soit sous forme imprimée ou lisible par la machine, de tous les Logiciels ainsi que de la documentation les accompagnant, à la même partie ou détruire les copies non cédées.F. Vous ne pouvez retirer aucune marque de droits d’auteur, marque de commerce ou autre ni aucune identiﬁ cation de produit des Logiciels et vous devez reproduire et inclure toutes ces notices ou identiﬁ cations de produit sur toutes les copies des Logiciels.Vous ne pouvez assembler en sens inverse, compiler en sens inverse ni retracer les Logiciels ni aucune de leurs cop-ies, de façon électronique ou mécanique, en tout ou en partie.Vous ne pouvez utiliser, copier, modiﬁ er, altérer ni céder les Logiciels ni aucune de leurs copies, en tout ou en partie, à l’exception de ce qui est expressément stipulé dans ce contrat.Si vous cédez la possession de toute copie ou de tout Logiciel à une autre partie, à l’exception de ce qui est autorisé au paragraphe E ci-dessus, votre licence est automatiquement résiliée.Termes, clauses et conditionsCette licence n’est effective que pour la durée de possession ou de crédit-bail du Produit, à moins d’une résiliation an-térieure. Vous pouvez résilier cette licence à tout moment en détruisant, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme que ce soit. Cette licence sera également résiliée, avec application immédiate, si les conditions de résiliation déﬁ nies ailleurs dans ce contrat se sont réalisées ou si vous ne respectez pas les termes, clauses et conditions qui y sont contenues. Au moment de la résiliation, vous acceptez de détruire, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme que ce soit.Vous reconnaissez avoir lu ce contrat, en avoir compris toute la substance et avoir accepté de respecter ses termes, clauses et conditions. Vous reconnaissez en outre qu’ils sont la description complète et exclusive du contrat conclu entre nous, contrat qui remplace et annule toute proposition ou contrat précédent, écrit ou oral, et toute autre commu-nication entre nous, relativement à l’objet du présent contrat.CF-19CTQZZBM.indb 28 2008/11/10 10:16:16

29AppendixSpeciﬁ cationsThis page provides the speciﬁ cations for the basic model. The model number is different according to the unit conﬁ guration. To check the model number:Check the bottom of the computer or the box the computer came in at the time of purchase. To check CPU speed, memory size and the hard disk drive (HDD) size:Run the Setup Utility ( Reference Manual “Setup Utility”) and select [Information] menu.[CPU Speed]: CPU speed, [System Memory]: Memory size, [Hard Disk]: Hard disk drive size Main Speciﬁ cationsModel No. CF-19KHRAXJM CF-19KHRAXAM CF-19KDRAXJM CF-19KDRAXCMCPU Intel® Core™ 2 Duo Processor U9300 (1.20 GHz, 3 MB*1 L2 cache, 800 MHz FSB)Chipset Mobile Intel® GS45 Express ChipsetMemory*1*2 2048 MB (4096 MB Max.)Video Memory*1*3*4UMA 797 MB Max. (When Memory is 2 GB) / UMA 1551 MB Max. (When Memory is 4 GB)UMA 1024 MB Max.Hard Disk Drive*4 160 GBDisplay Method 10.4 XGA type (TFT)Internal LCD*5 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots)External Display*6 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1280 × 768 dots/1280 × 1024 dots)Wireless LAN*7  page 30BluetoothTM *8  page 30LAN IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-TModem Data: 56 kbps (V.92) FAX: 14.4 kbpsSound WAVE and MIDI playback, Intel® High Deﬁ nition Audio subsystem support, Monaural speakerSecurity Chip TPM (TCG V1.2 compliant)*9Card Slot PC Card Type I or Type II x 1 (3.3 V: 400 mA, 5 V: 400 mA)ExpressCard*10 ExpressCard/34*11 or ExpressCard/54 x 1Smart Card*12 ISO7816 x 1SD Memory Card*13 x 1, Data transfer rate = 8 MB per second*14RAM Module Slot 200-pin, 1.8 V, SO-DIMM, DDR2 SDRAM, PC2-5300 CompliantInterface USB port (4-pin, USB 2.0) x 2, Serial Port (Dsub 9-pin male), Modem port (RJ-11), LAN port (RJ-45), External display port (Mini Dsub 15-pin female), Expansion Bus Connector (Dedicated 100-pin female), External Antenna Connector (Dedicated 50 Ω coaxial connector) x 2, IEEE 1394a Interface Connector (4-pin x 1), Microphone Jack (Miniature jack, 3.5 DIA, Stereo), Headphone Jack (Miniature jack, 3.5 DIA, Impedance 32 Ω, Output Power 4 mW x 2)Keyboard / Pointing Device 82 keys / Touch Pad / Touchscreen (Anti-Reﬂ ection, Stylus (included) touch capable) 82 keys / Touch Pad / Dual Touch (Anti-Re-ﬂ ection, Stylus (included) touch capable)Power Supply AC adaptor or Battery packAC Adaptor*23 Input: 100 V to 240 V AC, 50 Hz/60 Hz, Output: 16.0 V DC, 3.75 ABattery Pack Li-ion 10.65 V, 5.7 AhOperating Time*15 9 hours/ 10.0 hours*16Charging Time*15Power on Approx. 6.5 hoursPower off Approx. 4.5 hoursClock Battery Coin type lithium battery 3.0 VPower Consumption*17 Approx. 30 W*18 / Approx. 60 W (maximum when recharging in the ON state)Physical Dimensions (W × H × D)(excluding the hand strap/shoul-der strap)271 mm × 49 mm × 216 mm {10.7" × 1.93" × 8.5"}Weight (excluding the hand strap/shoul-der strap)Approx. 2.30 kg {Approx. 5.06 lb.} Approx. 2.30 kg {Approx. 5.06 lb.}CF-19CTQZZBM.indb 29 2008/11/10 10:16:16

$30Appendix Main Speciﬁ cationsOperation Environment Temperature: 5 °C to 35 °C {41 °F to 95 °F}Humidity: 30% to 80% RH (No condensation)Storage Environment Temperature: -20 °C to 60 °C {-4 °F to 140 °F}Humidity: 30% to 90% RH (No condensation)Operating SystemWindows Vista® Business Service Pack 1Microsoft® Windows® XP Professional Service Pack 2 with Advanced Security Technologies (NTFS File System)Microsoft® Windows® XP Tablet PC Edition 2005 (NTFS File System)Utility Programs Adobe Reader, PC Information Viewer, Loupe Utility, Intel® PROSet/Wireless Software*7, Blue-tooth™ Stack for Windows® by TOSHIBA*8, Wireless Switch Utility, Hotkey Settings, Battery Recalibration Utility, Panasonic Hand Writing, Display Rotation Tool, Inﬁ neon TPM Profession-al Package*19, Power Saving Utility, Wireless Connection Disable Utility*19, Concealed Mode Utility*21Setup Utility, Hard Disk Data Erase Utility*20, PC-Diagnostic Utility Wireless LAN <Only for model with wireless LAN>Data Transfer Rates IEEE802.11a : 54/48/36/24/18/12/9/6 Mbps (automatically switched)*22IEEE802.11b : 11/5.5/2/1 Mbps (automatically switched)*22IEEE802.11g : 54/48/36/24/18/12/9/6 Mbps (automatically switched)*22IEEE802.11n : (HT20) 144.4/130/117/115.6/104/86.7/78/65/58.5/57.8/52/43.3/39/28.926/19.5/14.4/13/6.5 Mbps (automatically switched)*22(HT40) 300/270/243/240/216/180/162/130/120/117/108/104/90/81/78/60/54/52/39/30/27/26/13 Mbps (automatically switched)*22Standards Supported IEEE802.11a / IEEE802.11b / IEEE802.11g / IEEE802.11n(Draft 2.0)Transmission method OFDM system, DSSS systemWireless Channels Used IEEE802.11a : Channels 36/40/44/48/52/56/60/64/100/104/108/112/116/132/136/140/149/153/157/161/165IEEE802.11b/IEEE802.11g : Channels 1 to 11IEEE802.11n : Channels 1-11/36/40/44/48/52/56/60/64/100/104/108/112/116/132/136/140/149/153/157/161/165RF Frequency Band IEEE802.11a : 5.18 GHz - 5.32 GHz, 5.5 GHz - 5.58 GHz, 5.66 GHz - 5.7 GHz, 5.745 GHz -5.825 GHzIEEE802.11b/IEEE802.11g : 2.412 GHz - 2.462 GHzIEEE802.11n : 2.412 GHz - 2.462 GHz, 5.15 GHz - 5.35 GHz, 5.5 GHz - 5.58 GHz, 5.66 GHz -5.7 GHz, 5.745 GHz - 5.85 GHz BluetoothTM <Only for model with Bluetooth>Bluetooth Version 2.0 + EDRTransmission method FHSS systemWireless Channels Used Channels 1 to 79RF Frequency Band 2.402-2.48 GHz*1 1 MB = 1,048,576 bytes*2 You can physically expand the memory up to 4096 MB, but the total amount of usable memory available will be less depending on the actual system conﬁ guration. *3 A segment of the main memory is allotted automatically depending on the computer’s operating status. The size of the Video Memory cannot be set by the user.*4 1 GB = 1,000,000,000 bytes. Your operating system or some application software will report as fewer GB.*5 A 16,777,216 color display is achieved by using the dithering function.*6 Maximum resolution depends on the speciﬁ cations of the external display. Display may be impossible using some connected external displays.*7 Only for model with wireless LAN*8 Only for model with Bluetooth*9 For information on TPM, click (Start) and input “c:\util\drivers\tpm\README.pdf” in [Start Search] and press Enter, and refer to the Installation Manual of “Trusted Platform Module (TPM)”. click [start] - [Run] and input “c:\util\drivers\tpm\README.pdf”, and refer to the Installation Manual of “Trusted Platform Module (TPM)”.*10 Only for model with ExpressCard slot*11 When using ExpressCard/34, the card slot cover cannot be closed.*12 Only for model with Smart Card slotSpeciﬁ cationsCF-19CTQZZBM.indb 30 2008/11/10 10:16:16$

Panasonic of North America 9TGCF-19B Toughbook CF-19 PC with WWAN, WLAN and Bluetooth User Manual CF 19CTQZZBM indb

Panasonic Corporation of North America Toughbook CF-19 PC with WWAN, WLAN and Bluetooth CF 19CTQZZBM indb

Users Manual

Navigation menu

Namespaces

Views

Navigation