Panasonic of North America 9TGWL12A Intel Centrino Advanced-N 6235 User Manual

Panasonic Corporation of North America Intel Centrino Advanced-N 6235

UserManual.wiki >

Panasonic of North America >

9TGWL12A User Manual >

User manual

ContentsGetting StartedOPERATING INSTRUCTIONSPersonal ComputerModel No. CF-31 seriesIntroduction ................................................................. 2Read Me First ............................................................ 3(Precautions)Description of Parts .................................................. 11First-time Operation ..................................................14Useful InformationOn-screen Manual ....................................................18Handling and Maintenance .......................................19Reinstalling Software ................................................21TroubleshootingTroubleshooting (Basic) ............................................23AppendixLIMITED USE LICENSE AGREEMENT ...................27Speciﬁ cations ...........................................................29LIMITED WARRANTY ..............................................32Please read these instructions carefully before using this product, and save this manual for future use.For further information about the com-puter, you can refer to the on-screen manual.To access the on-screen manual  page 18 “On-screen Manual”Getting StartedUseful InformationTroubleshootingAppendix

3Getting StartedRead Me FirstImportant Safety Instructions / Importantes Mesures De Sécurité<Only for model with modem>When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of ﬁ re, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet base-ment or near a swimming pool.2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.3. Do not use the telephone to report a gas leak in the vicinity of the leak.4. Use only the power cord and batteries indicated in this man-ual. Do not dispose of batteries in a ﬁ re. They may explode. Check with local codes for possible special disposal instruc-tions.SAVE THESE INSTRUCTIONS19-E-1<Pour modèles avec modem uniquement>Certaines mesures de sécurité doivent être prises pendant l’utilisation de matérial téléphonique aﬁ n de réduire les risques d’incendie, de choc électrique et de blessures. En voici quelquesunes:1. Ne pas utiliser l’appareil près de l’eau, p.ex., près d’une baignoire, d’un lavabo, d’un évier de cuisine, d’un bac à laver, dans un sous-sol humide ou près d’une piscine.2. Éviter d’utiliser le téléphone (sauf s’il s’agit d’un appareil sans ﬁ l) pendant un orage électrique. Ceci peut présenter un risque de choc électrique causé par la foudre.3. Ne pas utiliser l’appareil téléphonique pour signaler une fuite de gaz s’il est situé près de la fuite.4. Utiliser seulement le cordon d’alimentation et le type de piles indiqués dans ce manual. Ne pas jeter les piles dans le feu: elles peuvent exploser. Se conformer aux règlements perti-nents quant à l’élimination des piles.CONSERVER CES INSTRUCTIONS19-F-1<Only for model with wireless LAN/Bluetooth>This product and your HealthThis product, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this product however is far much less than the electromagnetic ener-gy emitted by wireless devices like for example mobile phones.Because this product operates within the guidelines found in radio frequency safety standards and recommendations, we believe this product is safe for use by consumers. These stan-dards and recommendations reﬂ ect the consensus of the sci-entiﬁ c community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.In some situations or environments, the use of this product may be restricted by the proprietor of the building or responsible representa-tives of the organization. These situations may for example include: Using this product on board of airplanes, or In any other environment where the risk of interference to other devices or services is perceived or identiﬁ ed as harmful.If you are uncertain of the policy that applies on the use of wireless devices in a speciﬁ c organization or environment (e.g. airports), you are encouraged to ask for authorization to use this product prior to turning on the product.Regulatory InformationWe are not responsible for any radio or television interference caused by unauthorized modiﬁ cation of this product. The cor-rection of interference caused by such unauthorized modiﬁ ca-tion will be the responsibility of the user. We and its authorized resellers or distributors are not liable for damage or violation of government regulations that may arise from failing to comply with these guidelines.26-M-1Information to the User<Uniquement les modèles avec réseau local sans ﬁ l et/ou Bluetooth>Ce produit et votre santéCe produit, comme tout autre appareil radio, émet de l’énergie radioélectrique. Toutefois, la quantité d’énergie émise par ce produit est beaucoup moins importante que l’énergie radioélec-trique émise par des appareils sans ﬁ l tels que les téléphones portables. L’utilisation de ce produit ne comporte aucun risque pour le consommateur du fait que cet appareil opère dans les limites des directives concernant les normes et les recom-mendations de sécurité sur les fréquences radio. Ces normes et recommandations reﬂ ètent le consensus de la communauté scientiﬁ que et résultent de délibérations de jurys et comités de scientiﬁ ques qui examinent et interprètent continuellement les nouveautés de la vaste littérature sur les recherches effectuées. Dans certaines situations ou environnements, l’utilisation de ce produit peut être restreinte par le propriétaire du bâtiment ou par les représentants responsables de l’organisation. Ces situa-tions peuvent être les suivantes par exemple : A bord d’un avion, ou Dans tout autre environnement où les risques d’interférence sur d’autres appareils ou services sont perçus ou identiﬁ -ables comme dangereux.Si vous n’êtes pas sûr de la réglementation applicable à l’utilisation d’appareils sans ﬁ l dans une organization ou un environnement spéciﬁ que, (par exemple dans un aéroport) nous vous invitons à demander l’autorisation d’utiliser ce produit avant sa mise en marche.Informations concernant la réglementationNous déclinons toute responsabilité pour toute interférence radio ou télévision causée par des modiﬁ cations non autorisées apportées à ce produit. La correction d’interférences causées par de telles modiﬁ cations non autorisées sera la seule respon-sabilité de son utilisateur. Nousmêmes, les revendeurs ofﬁ ciels et les distributeurs ne sommes pas responsable de tout dégât ou de toute violation des règlements de l’État pouvant découler du non-respect de ces directives.26-F-1Informations destinées aux utilisateurs

4Getting StartedRead Me FirstLithium Battery / Pile au lithiumLithium Battery!This computer contains a lithium battery to enable the date, time, and other data to be stored. The battery should only be exchanged by authorized service personnel.Warning!A risk of explosion from incorrect installation or misapplication may possibly occur.15-E-1Pile au lithium!Le micro-ordinateur renferme une pile au lithium qui permet de sauvegarder certaines données, notamment la date et l’heure. La pile ne doit être remplacée que par un technicien qualiﬁ é.Danger ! Risque d’explosion en cas de non respect de cette mise en garde!15-F-1Information on Disposal in other Countries outside the European UnionThese symbols are only valid in the European Union.If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.53-M-1CD/DVD Drive CautionCAUTION!THIS PRODUCT UTILIZES A LASER.USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HERE-IN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.REFER SERVICING TO QUALIFIED PERSONNEL.12-E-1Laser safety information is appropriate only when drive with laser is installed.12-M-2-1AVERTISSEMENT!CET APPAREIL UTILISE UN LASER.L’UTILISATION DE COMMANDES OU DE RÉGLAGES OU L’EXÉCUTION DE PROCÉDURES AUTRES QUE CELLES SPÉCIFIÉES ICI PEUVENT PROVOQUER UNE EXPOSITION À DES RADIATIONS DANGEREUSES.NE PAS OUVRIR LES COUVERCLES NI ESSAYER DE RÉPARER SOIMÊME.CONFIER TOUT TRAVAIL D’ENTRETIEN À UN PERSONNEL QUALIFIÉ.12-F-1Les mesures de sécurité relatives au laser ne s’appliquent que lors de l’installation d’une unité avec laser.12-F-2-1Safety Precautions<Only for model with wireless WAN>The following safety precautions must be observed during all phases of the operation, usage, service or repair of any Personal Computer or Handheld Computer incorporating wireless WAN modem. Manufacturers of the cellular terminal are advised to con-vey the following safety information to users and operating personnel and to incorporate these guidelines into all manuals supplied with the product. Failure to comply with these precautions violates safety standards of design, manufacture and intended use of the product. Panasonic assumes no liability for customer failure to comply with these precautions. When in a hospital or other health care facility, observe the restrictions on the use of mobiles. Switch Personal Computer or Handheld Computer incorporating wireless WAN modem off, if instructed to do so by the guidelines posted in sensitive areas. Medical equipment may be sensitive to RF energy. The operation of cardiac pacemakers, other implanted medical equipment and hearing aids can be affected by interfer-ence from Personal Computer or Handheld Computer incorporating wireless WAN modem placed close to the device. If in doubt about potential danger, contact the physician or the manufacturer of the device to verify that the equipment is properly shielded. Pacemaker patients are advised to keep their Personal Computer or Handheld Computer incorporating wireless WAN modem away from the pacemaker, while it is on. Switch off Personal Computer or Handheld Computer incorporating wireless WAN modem before boarding an aircraft. Make sure it cannot be switched on inadvertently. The operation of wireless appliances in an aircraft is forbidden to prevent interference with communications systems. Failure to observe these instructions may lead to the suspension or denial of cellular services to the offender, legal action, or both. Do not operate Personal Computer or Handheld Computer incorporating wireless WAN modem in the presence of ﬂ am-mable gases or fumes. Switch off the cellular terminal when you are near petrol stations, fuel depots, chemical plants or where blasting operations are in progress. Operation of any electrical equipment in potentially explosive atmospheres can constitute a safety hazard. Your Personal Computer or Handheld Computer incorporating wireless WAN modem receives and transmits radio fre-quency energy while switched on. Remember that interference can occur if it is used close to TV sets, radios, computers or inadequately shielded equipment. Follow any special regulations and always switch off Personal Computer or Hand-held Computer incorporating wireless WAN modem wherever forbidden, or when you suspect that it may cause interfer-ence or danger.

5Getting Started Road safety comes ﬁ rst! Do not use a Personal Computer or Handheld Computer incorporating wireless WAN modem while driving a vehicle. Do not place the computer with wireless WAN modem in an area where it could cause personal injury to the driver or passengers. It is recommended to stow the unit in the boot or secure stowage area while driving. Do not place the computer with wireless WAN modem in an area over an air bag or in the vicinity where an air bag may deploy. Air bags inﬂ ate with great force and if the computer with wireless WAN modem is placed in the air bag deployment area may be propelled with great force and cause serious injury to occupants of the vehicle. IMPORTANT!Personal Computer or Handheld Computer incorporating wireless WAN modem operate using radio signals and cellular networks cannot be guaranteed to connect in all conditions. Therefore, you should never rely solely upon any wireless device for essential communications, for example emergency calls.Remember, in order to make or receive calls, Personal Computer or Handheld Computer incorporating wireless WAN modem must be switched on and in a service area with adequate cellular signal strength.Some networks do not allow for emergency calls if certain network services or phone features are in use (e.g. lock func-tions, ﬁ xed dialing etc.). You may need to deactivate those features before you can make an emergency call.Some networks require that a valid SIM card be properly inserted in Personal Computer or Handheld Computer incorpo-rating wireless WAN modem.27-1-2Federal Communications Commission Radio Frequency Interference StatementNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal-lation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer-ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the Panasonic Service Center or an experienced radio/TV technician for help.WarningTo assure continued compliance, use only shielded interface cables when connecting to a computer or peripheral. Also, any changes or modiﬁ cations not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.FCC RF Exposure Warning: This equipment is provided with PC Card slot that could be used with wireless transmitters, which will be speciﬁ cally recommended when they become available. Other third-party wireless transmitters have not been RF exposure evaluated for use with this computer and may not comply with FCC RF exposure requirements.<Only for model with wireless LAN/wireless WAN/Bluetooth> This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment has been approved for portable operation, and does not require any minimum spacing be provided between antennas and all person’s body. This equipment may not be co-located or operated with any other antenna or transmitter.25-M-3<Only for model with wireless WAN> This PC with WWAN transmitter installed, has been ap-proved for mobile operation and to assure compliance with RF exposure requirements, a minimum of 20 cm (8 inches) must be maintained between the WWAN antenna located in top of LCD and all person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.<Optional Car Mounter / Port Replicator> This equipment is provided with external antenna connector(s) for connection to optional Car Mounter or Port Replicator for mobile external mounted antenna(s). External antenna(s) must be professionally installed and cannot exceed recommended maximum antenna gain as described in individual provided supplement instructions for wireless transmitters. For WLAN, the Car Mounter should be used with WLAN whip antenna, with 5dBi antenna gain or less. Also, user must maintain minimum 20 cm spacing between external antenna(s) and all person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.25-M-5<Only for model with wireless LAN>This product is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range.FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this product.25-M-W-5Responsible Party: Panasonic Corporation of North America One Panasonic Way Secaucus, NJ 07094 Tel No:1-800-LAPTOP5 (1-800-527-8675)6-M-1<Only for model with modem>FCC Regulation Notice for modemThis equipment contains a FCC approved modem.1. This equipment complies with CFR47 Part 68 rules. On the computer is a label that contains, among other infor-mation, the FCC registration number and ringer equivalence number (REN) for this equipment. If required, this informa-tion must be provided to the telephone company.Models for U.S.A.

6Getting StartedRead Me First2. An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. See Installation Instructions for details.3. The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all area, the sum of RENs should not exceed ﬁ ve (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.4. If your telephone equipment cause harm to the telephone network, the telephone company will notify you in advice that temporary discontinuance of service may be required. But if advice notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to ﬁ le a complaint with the FCC if you believe it is necessary.5. The telephone company may take changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modiﬁ cations to maintain uninterrupted service.6. If trouble is experienced with this equipment, for repair or warranty information, please contact Panasonic Corpora-tion of North America at DIAL TOLL FREE 1-800-LAPTOP5 (1-800-527-8675). If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.7. There are no user serviceable parts contained in this equip-ment.8. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is sub-ject to state tariffs.9. The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electron-ic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the ﬁ rst page of the transmission, the date and time it is sent and an identiﬁ ca-tion of the business or other entry, or other individual send-ing the message and the telephone number of the sending machine or such business, other entity, or individual. In order to program this information into your fax software, you should refer to the manual of the Fax software being used.10. According to the FCC’s electrical safety advisory, we rec-ommend that you may install an AC surge arrestor in the AC outlet to which this equipment is connected. Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equip-ment connected to AC power sources and that this is a major nationwide problem. “Caution : To reduce the risk of ﬁ re, use only No.26 AWG or larger (e.g., 24 AWG) UL listed or CSA certiﬁ ed telecommunica-tion line cord.” “ATTENTION : Pour réduire le risque d’incendie, utiliser unique-ment des conducteurs de télécommunications 26 AWG ou de section supérieure (p.ex. 24 AWG) UL énumérés ou CSA certi-ﬁ é.”16-M-1UL1604-conforming model. (The model which has description of “UL1604” in the bottom of the computer.)THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DI-VISION2, GROUPS A, B, C, AND D OR NON-HAZARDOUS LOCATIONS ONLY.WARNING-EXPLOSION HAZARD-SUBSTITUTION OF COM-PONENTS MAY IMPAIR SUITABILITY FOR CLASSI, DIVI-SION2.When connecting and using a device manufactured by a third party, enquire to the manufacturer as to whether the device suits CLASS1, DIVISION2.33-M-1-1USA Only: Disposal may be regulated in your community due to environmental considerations. For disposal or recy-cling information, please visit Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149 65-M-2<For USA-California Only>This product contains a Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply.See www.dtsc.ca.gov/hazardouswaste/perchlorate/38-M-1For Used in Motor Vehicle /Pour L’utilisation Dans Un Véhi-cule MotoriséWarning: Notebook Computer may be installed in a motor vehicle and visible to the driver only if used to support vehicle related functions such as vehicle information, system control, rear or side observation and navigation. If used for entertain-ment purpose, such as television reception or video play, it must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. Check with individual state/provincial laws to determine lawful use of this product while operating within a motor vehicle.Avertissement : L’ordinateur bloc-notes peut être installé dans un véhicule motorisé et dans le champ de vision du conduc-teur uniquement en tant que dispositif d’aide aux fonctions du véhicule, comme par exemple pour fournir des informations sur le véhicule, comme dispositif de contrôle de système, pour l’ob-servation à l’arrière ou sur les côtés du véhicule, ainsi que pour fournir de l’information routière. Pour toute utilisation à ﬁ n de divertissement, comme par exemple pour regarder la télévision ou jouer à des jeux vidéo, il doit être installé à l’arrière du siège du conducteur, en un emplacement où il ne sera pas visible, ni directement ni indirectement, pour le conducteur du véhicule motorisé. Vériﬁ ez les lois fédérales et nationales qui régissent l’utilisation légale de cet appareil à l’intérieur d’un véhicule mo-torisé.35-M-1External AntennaFCC RF Exposure Warning: This equipment is provided with external antenna connector(s) for connection to optional Car Mounter or Port Replicator for mobile external mounted antenna(s). Exter-nal antenna(s) must be professionally installed and cannot exceed recommended maximum antenna gain as described in individual provided supplement instructions for wireless transmitters. The maximum allowable antenna gain for the external WWAN base whip antenna for the cellular band is 7.0 dBi and PCS band is 3.5 dBi. Also, user must maintain minimum 20 cm spacing between external antenna(s) and all person’s body (excluding extremities of hands, wrist and feet) during wire-less modes of operation.32-M-1-1

7Getting StartedModels for Canada<Only for model with modem>Industry Canada (IC) Notice for modemThis equipment contains an Industry Canada approved modem unit.The Industry Canada label is afﬁ xed on the modem unit.EQUIPMENT ATTACHMENT LIMITATIONS“NOTICE: The Industry Canada label identiﬁ es certiﬁ ed equip-ment. This certiﬁ cation means that the equipment meets tele-communications network protective, operational and safety re-quirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecom-munications company. The equipment must also be installed us-ing an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.Repairs to certiﬁ ed equipment should be coordinated by a rep-resentative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.Users should ensure for their own protection that the electri-cal ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such con-nections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.”“NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.”REN: See bottom of the computerRESTRICTIONS CONCERNANT LE RACCORDEMENT DE MATÉRIEL“AVIS: L’étiquette d’Industrie Canada identiﬁ e le matériel homo-logué. Cette étiquette certiﬁ e que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’entreprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de raccordement.L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions énoncées ci-dessus n’empêche pas la dégrada-tion du service dans certaines situations.Les réparations de matériel homologué doivent être coordon-nées par un représentant désigné par le fournisseur.L’entreprise de télécommunications peut demander à l’utilisa-teur de débrancher un appareil à la suite de réparations ou de modiﬁ cations effectuées par l’utilisateur ou à cause de mauvais fonctionnement.Pour sa propre protection, l’utilisateur doit s’assurer que tous les ﬁ ls de mise à la terre de la source d’énergie électrique, des lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est parti-culièrement importante dans les régions rurales. Avertissement: L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à un service d’inspection des instal-lations électriques, ou à un électricien, selon le cas.”“AVIS: L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de ter-minaux qui peuvent être raccordés à une interface. La ter-minaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de touts les dispositifs n’excède pas 5.”IES: Voir sous le fond de l’ordinateur17-Ca-1Canadian ICES-003This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.7-M-2<Only for model with wireless LAN/Bluetooth>Industry CanadaThis product complies with RSS210 Industry Canada.Operation is subject to the following two conditions;(1) this device may not cause interference, and(2) this device must accept any interference, including interfer-ence that may cause undesired operation of the device.<Ne s’applique qu’aux modèes avec technologie Bluetooth/LAN sans ﬁ l/WAN sans ﬁ l>Industrie CanadaCet équipement est conforme à la norme CNR-210 d’ndustrie Canada. Son fonctionnement estsoumis aux deux conditions suivantes :(1) ce dispositif ne peut produire de brouillage, et(2) ce dispositif doit accepter le brouillage, y compris le brouilla-ge pouvant entraîner le fonctionnement non désiré de l’appareil.30-Ca-1-1<Only for model with wireless LAN>This product (local network devices) for the band 5150-5250 MHz is only indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems.High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.<Ne s’applique qu’aux modèes avec technologie LAN sans ﬁ l>Cet appareil (pour réseaux locaux radioélectriques) dans les bandes de fréquences 5150-5250 MHz est réervéàune utili-sation àl’intéieur aﬁ n de réuire le risque d’interféence avec les systèmes satellites mobiles bicanaux.Les radars forte puissance sont désignés comme étant les pre-miers utilisateurs (c’st-à-dire qu’ls ont la priorité) des bandes de fréquences 5250-5350 MHz et 5650-5850 MHz. Ces stations radars peuvent provoquer des interférences et/ou des domma-ges à ce périphérique.30-Ca-2-1This device has been designed to operate with whip antenna having a maximum gain of 5dB. A WLAN Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The Required antenna impedance is 50 ohms.To reduce potential radio interference to other users, the an-tenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that re-quired for successful communication.Cet appareil est conçu pour opérer avec l’antenne-fouet ayant un gain maximum de 5 dB. Les règlements d’Industrie Canada interdi-sent l’utilisation d’une antenne WLAN dont le gain serait supérieur à cette limite. L’antenne doit avoir une impédance de 50 ohms.

8Getting StartedRead Me FirstAﬁ n de réduire le risque d’interférence radioélectrique aux autres utilisateurs des bandes de fréquences, le type d’antenne et son gain doivent être tels que la puissance isotrope rayonnée équivalente (PIRE) n’est pas plus élevée que le niveau requis pour assurer la communication.25-Ca-1-1<Only for model with wireless LAN/wireless WAN/Bluetooth> This computer complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment. This PC with WLAN and/or Bluetooth transmitters installed, has been approved for portable operation and does not re-quire any minimum spacing be provided between antennas and all person’s body.<Ne s’applique qu’aux modèles avec technologie Bluetooth/LAN sans ﬁ l/WAN sans ﬁ l> Cet équipement est conforme aux limites d’exposition aux rayonnements d’Industrie Canada établies pour un environ-nement non contrôlé. Ce PC avec émetteurs WLAN et/ou Bluetooth a été approu-vé à des ﬁ ns d’opération mobile; aucun espace minimum entre les antennes et le corps de l’utilisateur n’est requis.FOR USE WITH MODEL NO. : CF-AA5713APOUR UTILISER AVEC MODÈLE : CF-AA5713A 20-Ca-1CSA C22 2 NO.213-conforming model. (The model which has description of “CSA C22 2 NO.213” in the bottom of the com-puter.)THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DI-VISION2, GROUPS A, B, C, AND D OR NON-HAZARDOUS LOCATIONS ONLY.WARNING-EXPLOSION HAZARD-SUBSTITUTION OF COM-PONENTS MAY IMPAIR SUITABILITY FOR CLASSI, DIVI-SION2.When connecting and using a device manufactured by a third party, enquire to the manufacturer as to whether the device suits CLASS1, DIVISION2.33-Ca-1External Antenna<For Canada>This device has been designed to operate with the WWAN antenna having a maximum gain of 7.0 dB for the cellular band and 3.5 dB for the PCS band. WWAN Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The Required antenna impedance is 50 ohms.To reduce potential radio interference to other users, the an-tenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that re-quired for successful communication.<Utilisation au Canada>Cet appareil est conçu pour opérer avec une antenne WWAN (réseau étendu sans ﬁ l) dont le gain maximum est ﬁ xé à 7.0 pour la bande cellulaire et à 3.5 pour la bande de service de communications personnelles (PCS). Les règlements d’Indus-trie Canada interdisent l’utilisation d’une antenne WWAN dont le gain serait supérieur à cette limite. L’antenne doit avoir une impédance de 50 ohms.Aﬁ n de réduire le risque d’interférence radioélectrique aux autres utilisateurs des bandes de fréquences, le type d’antenne et son gain doivent être tels que la puissance isotrope rayonnée équivalente (PIRE) n’est pas plus élevée que le niveau requis pour assurer la communication.32-Ca-1-1Models for AustraliaFor Used in Motor VehicleWarning: Notebook Computer may be installed in a motor vehicle and visible to the driver only if used to support vehicle related functions such as vehicle information, system control, rear or side observation and navigation. If the Notebook Computer is to be used for work or entertainment purposes, such as television reception, video play or other work programs, it must be installed in a position where it will NOT:(a) be visible, directly or indirectly, to the operator of the motor vehicle; or(b) cause distraction to drivers of other motor vehicles.Check with individual state laws to determine lawful use of this product while operating within a motor vehicle. If the visual display unit is, or is part of, a driver's aid, above rule is not applied. "Driver's aid" includes closed-circuit television security cameras, dis-patch systems, navigational or intelligent highway and vehicle system equipment, rear view screens, ticket-issuing machines and vehicle monitoring devices.35-A-1

9Getting StartedTHIS PRODUCT IS NOT INTENDED FOR USE AS, OR AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS, AIR TRAFFIC CONTROL EQUIPMENT/SYSTEMS, AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS*1, MEDICAL DEVICES OR ACCES-SORIES*2, LIFE SUPPORT SYSTEMS OR OTHER EQUIP-MENTS/DEVICES/SYSTEMS THAT ARE INVOLVED WITH ENSURING HUMAN LIFE OR SAFETY. PANASONIC WILL NOT BE RESPONSIBLE FOR ANY LIABILITY RESULTING FROM THE USE OF THIS PRODUCT ARISING OUT OF THE FOREGOING USES.*1 AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include Class2 Electrical Flight Bag (EFB) Systems and Class1 EFB Systems when used during critical phases of ﬂ ight (e.g., during take-off and landing) and/or mounted on to the aircraft. Class1 EFB Systems and 2 EFB Systems are deﬁ ned by FAA: AC (Advi-sory Circular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaﬂ ets) No.36.*2 As deﬁ ned by the European Medical Device Directive (MDD) 93/42/EEC. Panasonic cannot guarantee any speciﬁ cations, technolo-gies, reliability, safety (e.g. Flammability/Smoke/Toxicity/Radio Frequency Emission, etc) requirements related to aviation standards and medical equipment standards that differ from the speciﬁ cations of our COTS (Commercial-Off-The-Shelf) products.Panasonic cannot guarantee any speciﬁ cations, technolo-gies, reliability, safety (e.g. Flammability/Smoke/Toxicity/Radio Frequency Emission, etc) requirements related to aviation standards that exceed the speciﬁ cations of our COTS (Com-mercial-Off-The-Shelf) products.This computer is not intended for use in medical equipment in-cluding life-support systems, air trafﬁ c control systems, or other equipment, devices or systems that are involved with ensuring human life or safety. Panasonic cannot be held responsible in any way for any damages or loss resulting from the use of this unit in these types of equipment, devices or systems, etc.The CF-31 was developed based on thorough research into the real-world portable computing environments. Exhaustive pursuit of usability and reliability under harsh conditions led to innova-tions such has the magnesium alloy exterior, vibration damped hard disk drive and ﬂ oppy disk drive, ﬂ exible internal connec-tions. The CF-31’s outstanding engineering has been tested using the strict MIL-STD- 810F (for vibration and shock) and IP (for dust and water) based procedures.As with any portable computer device precautions should be taken to avoid any damage. The following usage and handling procedures are recommended. Before putting the computer away, be sure to wipe off any moisture.If a Malfunction or Trouble Occurs, Immediately Stop UseIf a Malfunction Occurs, Immediately Unplug the AC Plug and the Battery Pack This product is damaged Foreign object inside this product Smoke emitted Unusual smell emitted Unusually hotContinuing to use this product while any of the above conditions are present may result in ﬁ re or electric shock. If a malfunction or trouble occurs, immediately unplug the AC plug and remove the unit from this product. Then, contact your technical support ofﬁ ce for repair.Do Not Touch This Product In a Thunderstorm If Connected with the AC Cable or Any Other CablesElectric shock may result.Do Not Connect the AC Adaptor to a Power Source Other Than a Standard Household AC OutletOtherwise, a ﬁ re due to overheating may result. Connecting to a DC/AC converter (inverter) may damage the AC adaptor. On an airplane, only connect the AC adaptor/charger to an AC outlet speciﬁ cally approved for such use.Do Not Do Anything That May Damage the AC Cord, the AC Plug, or the AC AdaptorDo not damage or modify the cord, place it near hot tools, bend, twist, or pull it forcefully, place heavy objects on it, or bundle it tightly.Continuing to use a damaged cord may result in ﬁ re, short cir-cuit, or electric shock.Do Not Pull or Insert the AC Plug If Your Hands Are WetElectric shock may result.Clean Dust and Other Debris of the AC Plug RegularlyIf dust or other debris accumulates on the plug, humidity, etc. may cause a defect in the insulation, which may result in a ﬁ re. Pull the plug, and wipe it with a dry cloth.Pull the plug if the computer is not being used for a long pe-riod of time.Insert the AC Plug CompletelyIf the plug is not inserted completely, ﬁ re due to overheating or electric shock may result. Do not use a damaged plug or loose AC outlet.Close the Connector Cover Tightly When Using This Prod-uct Where Is a Lot of Water, Moisture, Steam, Dust, Oily Vapors, etc.The entry of foreign matter may cause a ﬁ re or electric shocks. If foreign matter has found its way inside, immediately turn the power off and unplug the AC cord, and then remove the battery pack. Then contact your technical support ofﬁ ce.Do Not Disassemble This ProductThe high-voltage areas inside may give you an electric shock, or foreign matter may enter and result in a ﬁ re.Keep SD Memory Cards Away from Infants and Small Chil-drenAccidental swallowing will result in bodily injury. In the event of accidental swallowing, see a doctor imme-diately.Do Not Place This Product on Unstable SurfaceIf balance is lost, this product may fall over or drop, resulting in an injury.Avoid StackingIf balance is lost, this product may fall over or drop, resulting in an injury.Do Not Leave This Product in High Temperature Environ-ment for a Long Period of TimeLeaving this product where it will be exposed to extremely high temperatures such as near ﬁ re or in direct sunlight may deform the cabinet and/or cause trouble in the internal parts. Continued use in such a resulting condition may lead to short-circuiting or insulation defects, etc. which may in turn lead to a ﬁ re or electric shocks.Do Not Block the Ventilation Hole (Exhaust)Using this product wrapped in cloth or on top of bedding or a blanket can block the ventilation hole and cause heat to build up inside. Possibly resulting in a ﬁ re.Hold the Plug When Unplugging the AC PlugPulling on the cord may damage the cord, resulting in a ﬁ re or electric shock.Do Not Move This Product While the AC Plug Is ConnectedThe AC cord may be damaged, resulting in ﬁ re or electric shock. If the AC cord is damaged, unplug the AC plug immediately.Use Only the Speciﬁ ed AC Adaptor With This ProductUsing an AC adaptor other than the one supplied (supplied with the unit or one sold separately as an accessory) may result in a ﬁ re.Do Not Subject the AC Adaptor to Any Strong ImpactUsing the AC adaptor after a strong impact such as being dropped may result in electric shock, short circuit, or ﬁ re.Precautions

10Getting StartedTake a Break of 10-15 Minutes Every HourUsing this product for long periods of time may have detrimental health effects on the eyes or hands.Do Not Turn the Volume Up To Loud When Using Head-phonesListening at high volumes that overstimulate the ear for long periods of time may result in loss of hearing.Do Not Connect a Telephone Line, or a Network Cable Other Than the One Speciﬁ ed, into the LAN PortIf the LAN port is connected to a network such as the ones listed right, a ﬁ re or electric shock may result. Networks other than 1000BASE-T, 100BASE-TX or 10BASE-T Phone lines (IP phone (Internet Protocol Telephone), Tele-phone lines, internal phone lines (on-premise switches), digital public phones, etc.)Precautions (Battery Pack)Do Not Use With Any Other ProductThe battery pack is rechargeable and was intended for the speciﬁ ed product. If it is used with a product other than the one for which it was designed, electrolyte leakage, generation of heat, ignition or rupture may result.Do Not Charge the Battery Using Methods Other Than Those Speciﬁ edIf the battery is not charged using one of the speciﬁ ed methods, electrolyte leakage, generation of heat, ignition or rupture may result.Do Not Throw the Battery Pack Into a Fire or Expose It to Excessive HeatGeneration of heat, ignition or rupture may result.Avoid Extreme Heat (Near the Fire, In Direct Sunlight, for Example)Electrolyte leakage, generation of heat, ignition or rupture may result.Do Not Insert Sharp Objects Into the Battery Pack, Expose It to Bumps or Shocks, Disassemble, or Modify ItElectrolyte leakage, generation of heat, ignition or rupture may result. If this product is subjected to a strong impact, stop using it im-mediately.Do Not Short the Positive (+) and Negative (-) ContactsGeneration of heat, ignition or rupture may result.  Do not place the battery pack together with articles such as necklaces or hairpins when carrying or storing.Do Not Use This Product with a Battery Pack Other Than the One Speciﬁ edUse only the speciﬁ ed battery pack ( page 11) with your prod-uct. Use of battery packs other than those manufactured and supplied by Panasonic may present a safety hazard (generation of heat, ignition or rupture).When the battery pack has become degraded, replace it with a new oneContinued use of a damaged battery pack may result in heat generation, ignition or battery rupture. Do not touch the terminals on the battery pack. The battery pack may no longer function properly if the contacts are dirty or damaged. Do not expose the battery pack to water, or allow it to become wet. If the battery pack will not be used for a long period of time (a month or more), charge or discharge (use) the battery pack until the remain-ing battery level becomes 30% to 40% and store it in a cool, dry place. This computer prevents overcharging of the battery by recharging only when the remaining power is less than approx. 95% of capacity. The battery pack is not charged when the computer is ﬁ rst purchased. Be sure to charge it before using it for the ﬁ rst time. When the AC adaptor is connected to the computer, charging begins automatically. Should the battery leak and the ﬂ uid get into your eyes, do not rub your eyes. Immediately ﬂ ush your eyes with clear water and see a doctor for medical treatment as soon as possible.Do Not Use With Exposing the Skin To This Product For a Long Period of TimeUsing this product with exposing the skin to the heat source of this product or AC adaptor for a long period of time can cause a low-temperature burn.Do Not Expose the Skin to This Product When Using the Product In a Hot or Cold EnvironmentBurns, low-temperature burns or frostbite may result. When it is necessary to expose the skin to this product such as to scan a ﬁ ngerprint, perform the operation in the short-est time possible.<Only for model with modem>Use the Modem with a Regular Telephone LineConnection to an internal phone line (on-premise switches) of a company or business ofﬁ ce, etc. or to a digital public phone or use in a country or area not supported by the computer may result in a ﬁ re or electric shocks. Do not place the computer near a television or radio receiver. Keep the computer away from magnets. Data stored on the hard disk may be lost.CAUTION:Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions.58-E-1ATTENTION:Il y a risque d’explosion si la batterie est remplacée par une batterie de type incorrect.Mettre au rebut les batteries usagées conformément aux instructions.58-F-1 NOTE  The battery pack may become warm during recharging or normal use. This is completely normal. Recharging will not commence if internal temperature of the battery pack is outside of the allowable temperature range (0 °C to 50 °C {32 °F to 122 °F}). ( Reference Manual “Battery Power”) Once the allow-able range requirement is satisﬁ ed, charging begins auto-matically. Note that the recharging time varies based on the usage conditions. (Recharging takes longer than usual when the temperature is 10 °C {50 °F} or below.) If the temperature is low, the operating time is shortened. Only use the computer within the allowable temperature range. This computer has a high temperature mode function that prevents the degradation of the battery in high temperature environments. ( Reference Manual “Battery Power”) A level corresponding to a 100% charge for high temperature mode is approximately equivalent to an 80% charge level for normal temperature mode. The battery pack is a consumable item. If the amount of time the computer can be run by using a particular battery pack becomes dramatically shorter and repeated recharging does not restore its performance, the battery pack should be replaced with a new one. When transporting a spare battery inside a package, brief-case, etc., it is recommended that it be placed in a plastic bag so that its contacts are protected. Always power off the computer when it is not in use. Leaving the computer on when the AC adaptor is not connected will exhaust the remaining battery capacity.Read Me First

11Getting StartedDescription of PartsA: Wireless LAN Antenna / Bluetooth Antenna <Only for model with wireless LAN> Reference Manual “Wireless LAN” <Only for model with Bluetooth> Reference Manual “Bluetooth”B: Camera <Only for model with Camera>C: Wireless WAN Antenna <Only for model with wireless WAN> Reference Manual “Wireless WAN”D: GPS Antenna (Rear side) <Only for model with GPS>E: LCD Reference Manual “Screen Input Operation” (Only for model with touchscreen)F: Function Key Reference Manual “Key Combinations”G: KeyboardH: Touch PadI: LED Indicator : SD Memory Card Indicator(Blinking: During access) Reference Manual “SD Memory Card” : Wireless readyThis indicator lights when Wireless LAN, Blue-tooth, and/or Wireless WAN are connected and ready. It does not necessarily indicate the On/Off condition of the wireless connection. Reference Manual “Wireless LAN”, “Bluetooth”, “Disabling/Enabling Wireless Communication”, “Wireless WAN” : Caps lock : Numeric key (NumLk) : Scroll lock (ScrLk) : Hard disk drive status : Multimedia pocket device status or the second battery status. : Battery status Reference Manual “Battery Power” : Power status(Off: Power off/Hibernation, Green: Power on, Blinking green: Sleep, Blinking green rapidly: Cannot power on or resume due to low tempera-ture.)J: Power SwitchK: Carrying HandleL: Stylus HolderM: Fingerprint Reader <Only for model with Fingerprint Reader>  Reference Manual “Fingerprint Reader”N: ExpressCard Slot  Reference Manual “PC Card / ExpressCard”O: PC Card Slot Reference Manual “PC Card / ExpressCard”P: Multimedia Pocket Reference Manual “Multimedia Pocket”Q: Wireless Switch Reference Manual “Disabling/Enabling Wireless Communication”R: Smart Card Slot Reference Manual “Smart Card”S: SD Memory Card Slot Reference Manual “SD Memory Card”T: Battery Pack Speciﬁ ed Battery pack: CF-VZSU46AUU: Ventilation Hole (Exhaust)A lithium ion battery that is recyclable powers the product you have purchased.Please call 1-800-8-BATTERY for information on how to recycle this battery.L’appareil que vous vous êtes procuré est alimenté par une batterie au lithium-ion.Pour des renseignements sur le recyclage de la batterie, veuillez composer le 1-800-8-BATTERY.48-M-1DELMAHIKJFBCAGLeft sideN P T UR SQO

12Getting StartedRight sideD HE*1 E*2 E*3FGA CBIJ L MNOPKQR SRear side BottomA: Hard Disk Drive Reference Manual “Hard Disk Drive”B: HDMI Port Reference Manual “External Display”C: SIM Card Slot <Only for model with wireless WAN> Insert the SIM card into the SIM card slot with the contact side facing down and the cut corner facing forward. Reference Manual “Wireless WAN”D: LAN Port Reference Manual “LAN”E: 2nd LAN Port*1 / Modem Port*2 / IEEE 1394 Interface Connector*3 *1 <Only for model with 2nd LAN> Reference Manual “LAN” *2 <Only for model with Modem> Reference Manual “Modem” *3 <Only for model with IEEE 1394> Reference Manual “IEEE 1394 Devices”F: USB Port (2.0) Reference Manual “USB Devices”G: USB Port (3.0) Reference Manual “USB Devices”H: DC-IN JackI: Security Lock A Kensington cable can be connected. For further information, read the manual that comes with the cable.J: USB Port (2.0) Reference Manual “USB Devices”K: External Antenna ConnectorL: Expansion Bus Connector Reference Manual “Port Replicator / Car Mounter”M: External Display Port (VGA) Reference Manual “External Display”N: Headphone Jack You can connect headphones or ampliﬁ ed speakers. When they are connected, audio from the internal speakers is not heard.O: Microphone Jack A condenser microphone can be used. If other types of microphones are used, audio input may not be pos-sible, or malfunctions may occur as a result. P: Serial PortQ: RAM Module Slot Reference Manual “RAM Module”R: Speaker <Only for model with Camera> Do not turn the speaker volume and/or microphone volume up too loud. Feedback noise may occur. Reference Manual “Key Combinations”S: Ventilation Hole (Intake)Description of Parts

13Getting Started This computer contains a magnet and magnetic products at the locations circled in the illustration at right. Avoid leaving metallic object or magnetic me-dia in contact with these areas.

14Getting Started PreparationA Check and identify the supplied accessories.If you do not ﬁ nd the described accessories, contact Panasonic Technical Support ( pages 32 - 36).• AC Adaptor . . . . . 1Model No: CF-AA5713A• AC Cord . . . . . . . 1 • Battery Pack . . . 1Model No: CF-VZSU46AU<Only for model with touchscreen>• Soft Cloth . . . . . . 1 • Tether . . . . . . . . . 1 • Stylus . . . . . . . . . 1( Reference Manual “Screen Input Operation”)• OPERATING INSTRUCTIONS (This book) . . . . . . . . . . . . . . . . .1B Read the LIMITED USE LICENSE AGREEMENT before breaking the seal on the computer’s packaging ( page 27).1 Inserting the Battery PackA Slide the latch (A) to the right to unlock the cover.B Slide the latch (A) down, and open the cover.C Insert the battery pack until it securely ﬁ ts the connector.D Close the cover until it clicks.E Slide the latch (B) to the left to lock the cover. CAUTION  Make sure the latch is securely locked. Otherwise the battery pack may fall when you carry the computer. Do not touch the terminals of the battery pack and the computer. Doing so can make the terminals dirty or damaged, and may cause malfunction of the battery pack and the computer. NOTE  Note that the computer consumes electricity even when the computer power is off. If the battery pack is fully charged, the battery will fully discharge in the fol-lowing period of time:• When power is off: Approx. 6 weeks• In sleep: Approx. 3 days*1• In hibernation: Approx. 6 days*1*1 If “Wake Up from wired LAN” is disabled, the period of time will be longer.543121First-time Operation

15Getting Started2 Attaching the stylus to the computer (only for model with touchscreen) Use the tether to attach the stylus to the computer so you will not lose it. There are holes (A) to attach it.2341 CAUTION  Do not pull the tether with excessive force. The stylus may hit the computer, person’s body or other objects when released.3 Opening the DisplayA Push and hold the latch (A), and lift open the display.4 Connect your computer to a power outlet. The battery charging starts automatically. CAUTION  Do not disconnect the AC adaptor and do not switch the wireless switch to on until the ﬁ rst-time operation procedure is completed. When using the computer for the ﬁ rst time, do not connect any peripheral device except the battery pack and AC adaptor. Handling the AC adaptor Problems such as sudden voltage drops may arise during periods of thunder and lightning. Since this could adversely affect your computer, an uninter-ruptible power source (UPS) is highly recommended unless running from the battery pack alone.5 Turn on the computer.A Slide and hold the power switch until the power indicator lights. CAUTION  Do not slide the power switch repeatedly. The computer will forcibly be turned off if you slide and hold the power switch for 4 seconds or longer. Once you turn off the computer, wait for 10 seconds or more before you turn on the computer again. Do not perform the following operation until the hard disk drive indicator turns off. Connecting or disconnecting the AC adaptor Sliding the power switch223131445151

16Getting Started Touching the keyboard, touch pad or touchscreen (only for model with touchscreen) Closing the display Turn on/off the wireless switch When the CPU temperature is high, the computer may not start up to prevent overheating of the CPU. Wait until the computer cools down, and then turn the power on again. If the computer does not power on even after cooling down, contact Panasonic Technical Support ( pages 32 - 36). Any changes from the default setting of the Setup Utility must not be made until the First-time Operation is completed.6 Setup Windows. Follow the on-screen instructions. The computer restarts several times. Do not touch the keyboard or touch pad, and wait until the hard disk drive indicator has turned off. After the computer is turned on, the screen remains black or unchanged for a while. This is not a malfunction. Wait for a moment until the Windows setup screen appears. During setup of Windows, use the touch pad and clicking to move the cursor and to click an item. Setup of Windows will take approximately 20 minutes. Go to the next step, conﬁ rming each message on the display. “Join a wireless network” screen may not appear. You can set the Wireless Network after the setup of Windows is complete. CAUTION  You can change the user name, password, image and security setting after setup of Windows. Remember your password. If you forget the password, you cannot use Win-dows. Creating a password reset disk beforehand is recommended. Do not use the following words for user name: CON, PRN, AUX, CLOCK$, NUL, COM1 to COM9, LPT1 to LPT9, @. In particular, if you create a user name (ac-count name) that includes the “@” mark, a password will be requested at the log-on screen, even if no password has been set. If you try to log on without en-tering a password, “The user name or password is incorrect.” may be displayed and you will not be able to log on to Windows ( page 24).7 <Only for model with touchscreen> Perform the touchscreen calibration. Before performing the calibration, close Tablet PC Input Panel. Calibration by an administrator NOTE  At ﬁ rst, log on to Windows as an administrator and perform this calibration.A Click (Start) - [Control Panel] - [Hardware and Sound] - [Tablet PC Set-ting].B Click [Calibrate].C Using the stylus, touch each of the “+” target marks one by one, and then click [Yes].D Click [OK]. Calibration by a standard user NOTE  Perform the following calibration for each user.A Click (Start) - [Control Panel] - [Hardware and Sound] - [Tablet PC Set-ting].B Click [Calibrate].C Using the stylus, touch each of the “+” target marks one by one, and then click [Yes].First-time Operation

17Getting Started NOTE  PC Information Viewer This computer periodically records the management information of the hard disk, etc. The maximum data volume for each record is 1024 bytes. This information is only used for estimating the cause in the case when the hard disk goes down by any possibility. They are never sent to outside via network nor used for any other purpose except for the purpose described the above. To disable the function, add the check mark for [Disable the automatic save function for management information history] in [Hard Disk Status] of PC Information Viewer, and click [OK]. ( Reference Manual “Checking the Computer’s Usage Status”) Precaution against Starting Up/Shutting Down Do not do the following Connecting or disconnecting the AC adaptor Sliding the power switch Touching the keyboard, touch pad, touchscreen (only for model with touchscreen), or external mouse Closing the display Turn on/off the wireless switch NOTE  To conserve power, the following power saving methods are set at the time of purchase. The screen automatically turns off after 10 minutes of inactivity. The computer automatically enters sleep*2 after 20 minutes of inactivity.*2 Refer to Reference Manual “Sleep and Hibernation Functions” about resuming from sleep. To change the partition structureYou can shrink a part of an existing partition to create unallocated disk space, from which you can create a new parti-tion. This computer has a single partition as default setting.A Click (Start) and right-click [Computer], then click [Manage]. A standard user needs to enter an administrator password.B Click [Disk Management].C Right-click the partition for Windows (“c” drive in the default setting), and click [Shrink Volume]. The partition size depends on the computer speciﬁ cations.D Input the size in [Enter the amount of space to shrink in MB] and click [Shrink]. You cannot input a larger number than the displayed size. To select [Reinstall to the ﬁ rst 3 partitions.] in reinstalling Windows 7 ( page 22), 30000 MB or more is nec-essary for [Total size after shrink in MB].E Right-click [Unallocated] (the shrunk space in the step D) and click [New Simple Volume].F Follow the on-screen instructions to make the settings, and click [Finish].Wait until formatting is completed. NOTE  You can create an additional partition using remaining unallocated space or newly creating unallocated space. To delete a partition, right-click the partition and click [Delete Volume] in step C.D Click [OK]. Perform the calibration for the orientation to be used.

18Useful InformationOn-screen ManualYou can access the Reference Manual on the computer screen. Reference Manual The Reference Manual contains the practical information to help you fully enjoy the computer’s performance.To access the Reference Manual:Double-click on the desktop. Alternatively click (Start) - [All Programs] - [Panasonic] - [On-Line Manuals] - [Reference Manual]. Important Tips The Important Tips will provide you with the battery information so that you can use the battery pack in the optimum condition to obtain longer operation time.To access the Important Tips:Double-click on the desktop. Alternatively click (Start) - [All Programs] - [Panasonic] - [On-Line Manuals] - [Important Tips]. NOTE  When you access the document of PDF format for the ﬁ rst time, the License Agreement of the Adobe Reader may be displayed. Read it carefully and select [Accept] to proceed. When Adobe Reader update notice is displayed, we recommend you follow the on-screen procedure and update.See http://www.adobe.com/ for the latest version of Adobe Reader.

19Useful InformationHandling and MaintenanceOperation environment Place the computer on a ﬂ at stable surface not subject to shock, vibration, and danger of dropping. Do not place the computer upright or turn it over. If the computer is exposed to an extremely strong impact, it may become dam-aged. Operating environmentTemperature: Operation : -10 °C to 50 °C {14 °F to 122 °F} (IEC60068-2-1, 2)*1 Storage : -20 °C to 60 °C {-4 °F to 140 °F} Humidity: Operation : 30% to 80% RH (No condensation) Storage : 30% to 90% RH (No condensation) Even within the above temperature/humidity ranges, operation for a long time in extreme environments, smoking nearby, or operation in places where oil is used or where there is a lot of dust will result in the product deterioration and will shorten the product life.*1 Do not expose the skin to this product when using the product in a hot or cold environment. ( page 10)If the computer is wet in temperatures of 0 °C {32 °F} or below, freeze damage may occur. Make sure to dry off the computer in such temperatures. Do not place the computer in the following areas, otherwise the computer may be damaged. Near electronic equipment. Image distortion or noise may occur. In extremely high or low temperature. As the computer can become hot during operation, keep it away from items that are sensitive to heat.Handling cautionsThis computer is designed to minimize shock to parts such as the LCD and the hard disk drive and equipped with a drip-proof keyboard, but no warranty is provided against any trouble caused by shock. Be extremely careful when han-dling the computer. When carrying the computer: Turn off the computer. Remove all external devices, cables, PC Cards and other protruding objects. Remove a disc in the CD/DVD drive. Do not drop or hit the computer against solid objects. Do not leave the display open. Do not grip the display part. Do not put anything (e.g., a piece of paper) between the display and keyboard. When you board an airplane, take the computer with you and never put it in your checked luggage. When using the computer on airplane, follow the airline’s instructions. When carrying a spare battery, put it in a plastic bag to protect its terminals. The touch pad is designed to be used by ﬁ nger tip. Do not place any object on its surface and do not press down strongly with sharp-pointed or hard objects that may leave marks (e.g., nails, pencils and ball point pens). Avoid any harmful substances such as oil from getting into the touch pad. The cursor may not work correctly. Be careful not to get injured by dropping or getting hit when carrying the computer.<Only for model with touchscreen> Use only the included stylus to touch the touchscreen. Do not place any object on its surface and do not press down strongly with sharp-pointed or hard objects that may leave marks (e.g., nails, pencils and ball point pens). Do not use the touchscreen when dust or dirt (e.g., oil) is on the screen. Otherwise foreign particles on the screen/stylus can scratch the screen surface or obstruct the stylus operation. Use the stylus only for touching the screen. Using it for any other purpose may damage the stylus and result in scratches on the screen. When using peripheral devicesFollow these instructions and the Reference Manual to avoid any damage to the devices. Carefully read the instruction manuals of the peripheral devices. Use the peripheral devices conforming to the computer’s speciﬁ cations. Connect to the connectors in the correct direction. If it is hard to insert, do not try forcibly but check the connector’s shape, direction, alignment of pins, etc. If screws are included, fasten them securely. Remove the cables when you carry the computer. Do not pull the cables forcibly.

20Useful Information Preventing your computer from unauthorized use via wireless LAN/Bluetooth/wireless WAN<Only for model with wireless LAN/Bluetooth/wireless WAN> Before using wireless LAN/Bluetooth/wireless WAN, make the appropriate security settings such as data encryp-tion. Battery Recalibration The battery recalibration may take a long time due to the large battery capacity. This is not a malfunction. Full charge: Approximately 3.5 hours (with Main Battery) / 6.5 hours (with Main Battery + Second Battery) Complete discharge: Approximately 4.0 hours (with Main Battery) / 6.0 hours (with Main Battery + Second Bat-tery)MaintenanceTo clean the LCD panelIf drops of water or other stains get on the surface of the LCD panel, wipe them off immediately. Failure to do so may result in staining.<Only for model with touchscreen>Use the soft cloth included with the computer. (For further information, refer to “Suggestions About Cleaning the LCDSurface”.  Reference Manual “Screen Input Operation”)To clean areas other than the LCD panelWipe with a soft dry cloth such as gauze. When using detergent, dip a soft cloth in water-diluted detergent and wring it thoroughly. CAUTION  Do not use benzene, thinner, or rubbing alcohol since it may adversely affect the surface causing discoloration, etc. Do not use commercially-available household cleaners and cosmetics, as they may contain components harmful to the surface. Do not apply water or detergent directly to the computer, since liquid may enter inside of the computer and cause malfunction or damage.Handling and Maintenance

21Useful InformationReinstalling SoftwareReinstalling software will return the computer to the default condition. When you reinstall the software, the hard disk data will be erased.Back up important data to other media or an external hard disk before reinstallation.n Hard Disk Recovery CAUTION Area usable by WindowsHard diskHDD Recovery partitionRecovery partitionl Do not delete the recovery partition on the hard disk. The disk space in the partition is not available to store data.Preparationl Remove all peripherals.l Connect the AC adaptor and do not remove it until reinstallation is complete.1 Turn on the computer, and press F2 or Del while [Panasonic] boot screen is displayed.The Setup Utility starts up.l If the password is requested, enter the Supervisor Password.2 Write down all of the contents of the Setup Utility and press F9.At the conrmation message, select [Yes] and press Enter.3 Press F10.At the conrmation message, select [Yes] and press Enter.Computer will restart.4 Press F2 or Del while [Panasonic] boot screen is displayed.The Setup Utility starts up.l If the password is requested, enter the Supervisor Password.5 Select the [Exit] menu, then select [Recovery Partition] and press Enter.6 Click [Reinstall Windows] and click [Next].The License Agreement screen appears.7 Click [Yes, I agree to the provisions above and wish to continue!] and click [Next].8 Select the settings and click [Next].l [Reinstall Windows to the whole Hard Disk to factory default.] Select this option when you want to reinstall Windows to the factory default. After reinstallation, you can create a new partition. For how to create a new partition, refer to “To change the partition structure” ( page 17).l [Reinstall to the System and OS partitions.]*1 Select this option when the hard disk has already been divided into several partitions. For how to create a new partition, refer to “To change the partition structure” ( page 17). You can keep the partition structure.*1 This does not appear if Windows cannot be reinstalled to the partition containing boot les and the area usable by Win-dows.9 Attheconrmationmessage,click[OK].10 SelectOS(32bitor64bit)andclick[OK].11 Attheconrmationmessage,click[OK].Reinstallation starts according to the instructions on the screen.l Do not interrupt reinstallation, for example by turning off the computer. Otherwise reinstallation may become unavailable as Windows may not start up or the data may be corrupted.12 Whenendingscreenisdisplayed,click[OK]toturnoffthecomputer.13 Turn on the computer.l If the password is requested, enter the Supervisor Password.14 Perform the “First-time Operation” ( page 15).15 Start the Setup Utility and change the settings as necessary.16 Perform Windows Update.CF-31 Useful Information.indd 21 2012/04/26 16:32:51

22Useful Information Using Recovery DiscUse the Recovery Disc for reinstallation in the following conditions. You have forgotten the administrator password. Reinstallation is not complete. The recovery partition may be broken. NOTE  To change OS from 32 bit to 64 bit, or vice versa, reinstall OS using the recovery partition in the hard disk.Preparation Prepare the Recovery Disc ( Reference Manual “Recovery Disc Creation Utility”) Remove all peripherals. Connect the AC adaptor and do not remove it until reinstallation is complete.1 Turn on the computer, and press F2 or Del while [Panasonic] boot screen is displayed.The Setup Utility starts up. If the password is requested, enter the Supervisor Password.2 Write down all of the contents of the Setup Utility and press F9.At the conﬁ rmation message, select [Yes] and press Enter.3 Press F10.At the conﬁ rmation message, select [Yes] and press Enter.Computer will restart.4 Press F2 or Del while [Panasonic] boot screen is displayed.The Setup Utility starts up. If the password is requested, enter the Supervisor Password.5 Set the Recovery Disc into the CD/DVD drive.6 Select the [Exit] menu, then select [TEAC DV-W28S-V] in [Boot Override].7 Press Enter.The computer will restart.8 Click [Reinstall Windows] and click [Next].The License Agreement screen appears.9 Click [Yes, I agree to the provisions above and wish to continue!] and click [Next].10 Select the settings and click [Next]. [Reinstall Windows to the whole Hard Disk to factory default.]Select this option when you want to reinstall Windows to the factory default. After reinstallation, you can create a new partition. For how to create a new partition, refer to “To change the partition structure” ( page 17). [Reinstall to the ﬁ rst 3 partitions.]*2Select this option when the hard disk has already been divided into several partitions. For how to create a new partition, refer to “To change the partition structure” ( page 17).You can keep the partition structure.*2 This does not appear if Windows cannot be reinstalled to the partition containing boot ﬁ les and the area usable by Windows.11 At the conﬁ rmation message, click [YES].Reinstallation starts. (It will take approximately 30 minutes.)According to the screen, replace the Recovery Disc. Do not interrupt reinstallation, for example by turning off the computer. Otherwise reinstallation may become unavailable as Windows may not start up or the data may be corrupted.12 When “Ending process.” is displayed, remove the Recovery Disc, and then click [OK] to turn off the computer.13 Turn on the computer. If the password is requested, enter the Supervisor Password.14 Perform the “First-time Operation” ( page 15).15 Start the Setup Utility and change the settings as necessary.16 Perform Windows Update.Reinstalling Software

23TroubleshootingTroubleshooting (Basic)Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the “Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, con-tact Panasonic Technical Support ( pages 32 - 36). You can also check the computer’s status in the PC Information Viewer ( Reference Manual “Troubleshooting (Advanced)”). Starting UpCannot start up.The power indicator or bat-tery indicator is not lit. Connect the AC adaptor. Insert a fully charged battery. Remove the battery pack and the AC adaptor, then connect them again.  If a device is connected to the USB port, disconnect the device, or set [USB Port] or [Legacy USB Support] to [Disable] in the [Advanced] menu of the Setup Utility. If a device is connected to the ExpressCard slot, disconnect the device, or set [ExpressCard Slot] to [Disable] in the [Advanced] menu of the Setup Utility. Press Fn + F8 to turn off the concealed mode.The power is turned on but “Warming up the system (up to 32 minutes)” appears. The computer is warming up before start up. Wait for the computer to start up (takes up to 32 minutes). If, “Cannot warm up the system” is displayed, the computer failed to warm up and will not start. In this case, turn off the computer, leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, and then turn on the power again.Cannot turn on the computer.The computer does not re-sume from sleep.(The power indicator blinks quickly in green.) Leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, then turn on the power again.After adding or changing the RAM module, the power is turned on but nothing is displayed on the screen. Turn off the computer and remove the RAM module, then conﬁ rm whether the RAM module has compliant to speciﬁ cation. When the RAM module has conformed to speciﬁ -cation, install it again.The computer does not enter sleep mode while the screen saver is running. (The screen stays black.) Slide and hold the power switch for four seconds or longer to shut down the computer forcibly. (Data not saved will be lost.) Then disable the screen saver.You have forgotten the pass-word. Supervisor Password or User Password: Contact Panasonic Technical Support ( pages 32 - 36). Administrator password:  If you have a password reset disk, you can reset the administrator password. Set the disk and enter any wrong password, then follow the on-screen instructions and set a new password. If you do not have a password reset disk, reinstall ( page 21) and set up Windows, and then set a new password.“Remove disks or other media. Press any key to restart” or a similar message appears. A ﬂ oppy disk is in the drive (optional) and it does not contain system startup information. Remove the ﬂ oppy disk and press any key. If a device is connected to the USB port, disconnect the device, or set [USB Port] or [Legacy USB Support] to [Disable] in the [Advanced] menu of the Setup Utility. If a device is connected to the ExpressCard slot, disconnect the device, or set [ExpressCard Slot] to [Disable] in the [Advanced] menu of the Setup Utility. If the problem persists after removing the disk, it may be a hard disk failure. Contact Panasonic Technical Support ( pages 32 - 36).Windows startup and opera-tion is slow. Press F9 in the Setup Utility ( Reference Manual “Setup Utility”) to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again. (Note that the processing speed depends on the ap-plication software, so this procedure may not make Windows faster.) If you installed a resident software after purchase, turn off the residence.The date and time are incor-rect. Make the correct settings.Click (Start) - [Control Panel] - [Clock, Language, and Region] - [Date and Time]. If the problem persists, the internal clock battery may need to be replaced. Contact Panasonic Technical Support ( pages 32 - 36). When the computer is connected to LAN, check the date and time of the server. The 2100 A.D. or later year will not be correctly recognized on this computer.

24Troubleshooting Starting Up[Executing Battery Recali-bration] screen appears. The Battery Recalibration was cancelled before Windows was shut down last time. To start up Windows, turn off the computer by the power switch, and then turn on.[Enter Password] does not appear when resuming from sleep/hibernation. Select [Enabled] in [Password On Resume] in the [Security] menu of the Setup Utility ( Reference Manual “Setup Utility”). The Windows password can be used instead of the password set in the Setup Utility.A Click (Start) - [Control Panel] - [User Accounts and Family Safety] - [Add or re-move user accounts] and select the account, and set the password.B Click (Start) - [Control Panel] - [System and Security] - [Power Option] - [Require a password when the computer wakes] and add a check mark for [Require a pass-word].Cannot resume.  An error may occur when the computer automatically enters the sleep or hibernation mode while the screensaver is active. In this case, turn off the screensaver or change the pattern of the screensaver.Other startup problems.  Press F9 in the Setup Utility ( Reference Manual “Setup Utility”) to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again. Remove all peripheral devices. Check to see if there was a disk error.A Remove all peripheral devices including external display.B Click (Start) - [Computer] and right-click [Local Disk (C:)], and click [Properties].C Click [Tools] - [Check Now...]. A standard user needs to enter an administrator password.D Select the option in [Check disk options] and click [Start].E Click [Schedule disk check] and restart the computer. Start the computer in Safe Mode and check the error details. When the [Panasonic] boot screen disappears*1 at startup, press and hold F8 until the Windows Advanced Options Menu is displayed. Select the Safe Mode and press Enter.*1 When [Password on boot] is set to [Enabled] in the [Security] menu of the Setup Utility, [Enter Password] appears after the [Panasonic] boot screen disappears. As soon as you enter the password and press Enter, press and hold F8. Entering PasswordEven after entering the pass-word, password input screen is displayed again.  The computer may be in ten-key mode.If the NumLk indicator lights, press NumLk to disable the ten-key mode, and then input. The computer may be in Caps Lock mode.If the Caps Lock indicator lights, press Caps Lock to disable the Caps Lock mode, and then input.Cannot log on to Windows. (“The user name or pass-word is incorrect.” is dis-played.) The user name (account name) includes the “@” mark. - If another user account name exists:Log on to Windows using another user account name, and delete the account name that includes “@”. Then create a new account name. - If no other account name exists:You need to reinstall Windows ( page 21). Shutting downWindows does not shut down. Remove the USB device and the ExpressCard. Wait 1 or 2 minutes. It is not a malfunction.Troubleshooting (Basic)

$25Troubleshooting DisplayNo display.  The external display is selected. Press Fn + F3 or + P to switch the display. Wait until the display has been switched completely before pressing Fn + F3 or + Pagain. When using an external display, Check the cable connection. Turn on the display. Check the settings of external display. The display is turned off by the power-saving function. To resume, do not press the direct selection keys, but press any other key like Ctrl. The computer entered sleep or hibernation by the power-saving function. To resume, press the power switch.The screen is dark.  The screen is darker when the AC adaptor is not connected. Press Fn + F2 and adjust the brightness. As you increase the brightness, battery consumption increases. You can separately set the brightness for when the AC adaptor is connected and when not connected. Press Fn + F8 to turn off the concealed mode.The screen does not be-come bright even if pressing Fn + F2. The brightness is set low to avoid malfunction where surrounding temperature is high. Use it in an environment of between -10 °C and 50 °C {14 °F to 122 °F}.The screen is disordered.  Changing the number of display colors and resolution may affect the screen. Restart the computer. Connecting/disconnecting an external display may affect the screen. Restart the com-puter.During Simultaneous display, one of the screens becomes disordered. When using the Extended Desktop, use the same display colors for the external display as those used by the LCD. If you continue to experience problems, try changing the display.Click (Start) - [All Programs] - [Panasonic] - [Display Selector]. Simultaneous display cannot be used until Windows startup is complete (during Setup Utility, etc.).The external display does not work normally. If the external display does not support the power saving function, it may not work nor-mally when the computer enters the power saving mode. Turn off the external display.<Only for model with GPS>The cursor cannot be con-trolled properly. Operate the following steps.A Restart the computer and press F2 or Del while [Panasonic] boot screen is dis-played.B Set [GPS] to [Disable] in the sub-menu of [Serial and Parallel Port Settings] in the [Advanced] menu of the Setup Utility.C Press F10 and select [Yes] at the conﬁ rmation message, and press Enter.The computer will restart.D Log on to Windows as an administrator.E Click (Start) and input “c:\util\drivers\gps\GPS.reg” in [Search programs and ﬁ les], and press Enter.F Click [Yes], click [Yes], and click [OK]. Then restart the computer.G Press F2 while [Panasonic] boot screen is displayed.H Set [GPS] to [Enable] in the sub-menu of [Serial and Parallel Port Settings] in the [Advanced] menu.I Press F10 and select [Yes] at the conﬁ rmation message, and press Enter.$

$26Troubleshootingn Touch Pad / Touchscreen (only for model with touchscreen)The cursor does not work. l When using the external mouse, connect it correctly.l Restart the computer using the keyboard. Press and press è two times, and press  to select [Restart] and press Enter.l If the computer does not respond to keyboard commands, read “No response” (è below).Cannot input using the touch pad.l Set [Touch Pad] to [Enable] in the [Main] menu of the Setup Utility.l The drivers for some mice may disable the touch pad. Check your mouse’s operating instructions.<Only for model with touch screen>Cannot input using the touchscreen.l Set [Touchscreen Mode] to [Auto] or [Tablet] in the [Main] menu of the Setup Utility.Cannot point the correct posi-tion using the included stylus.l Perform the touchscreen calibration (è page 16).n Reference ManualThe Reference Manual is not displayed.l Install Adobe Reader.A Log on to Windows as an administrator.B Click (Start) and input “c:\util\reader\AdbeRdr1001_en_US.exe” in [Search pro-grams and les] then press Enter.C Update Adobe Reader to its latest version. If your computer is connected to the internet, start up Adobe Reader and click [Help] - [Check for Updates...].n OthersNo response. l Press Ctrl+Shift+Esc to open Task Manager and close the software application that is not responding.l An input screen (e.g., password input screen at startup) may be hidden behind another window. Press Alt+Tab to check.l Slide the power switch for 4 seconds or longer to shut down the computer, and then slide the power switch to turn it on. If the application program does not work normally, uninstall and reinstall the program. To uninstall, click (Start) - [Control Panel] - [Pro-grams] - [Uninstall a program].Troubleshooting (Basic)CF-31 Troubleshooting.indd 26 2012/04/26 16:39:45$

27AppendixLIMITED USE LICENSE AGREEMENTTHE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC PRODUCT (“PRODUCT”) ARE LICENSED ONLY TO THE END-USER (“YOU”), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY DEEMED TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE.Panasonic Corporation has developed or otherwise obtained the Programs and hereby licenses their use to you. You assume sole responsibility for the selection of the Product (including the associated Programs) to achieve your intend-ed results, and for the installation, use and results obtained therefrom.LICENSEA. Panasonic Corporation hereby grants you a personal, non-transferable and non-exclusive right and license to use the Programs in accordance with the terms and conditions stated in this Agreement. You acknowledge that you are receiving only a LIMITED LICENSE TO USE the Programs and related documentation and that you shall obtain no title, ownership nor any other rights in or to the Programs and related documentation nor in or to the algorithms, concepts, designs and ideas represented by or incorporated in the Programs and related documentation, all of which title, ownership and rights shall remain with Panasonic Corporation or its suppliers.B. You may use the Programs only on the single Product which was accompanied by the Programs.C. You and your employees and agents are required to protect the conﬁ dentiality of the Programs. You may not distrib-ute or otherwise make the Programs or related documentation available to any third party, by time-sharing or other-wise, without the prior written consent of Panasonic Corporation.D. You may not copy or reproduce, or permit to be copied or reproduced, the Programs or related documentation for any purpose, except that you may make one (1) copy of the Programs for backup purposes only in support of your use of the Programs on the single Product which was accompanied by the Programs. You shall not modify, or at-tempt to modify, the Programs.E. You may transfer the Programs and license them to another party only in connection with your transfer of the single Product which was accompanied by the Programs to such other party. At the time of such a transfer, you must also transfer all copies, whether in printed or machine readable form, of every Program, and the related documentation, to the same party or destroy any such copies not so transferred.F. You may not remove any copyright, trademark or other notice or product identiﬁ cation from the Programs and you must reproduce and include any such notice or product identiﬁ cation on any copy of any Program.YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANICALLY OR ELECTRONICALLY TRACE THE PROGRAMS, OR ANY COPY THEREOF, IN WHOLE OR IN PART.YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PROGRAMS OR ANY COPY THEREOF, IN WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE.IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO ANOTHER PARTY, EXCEPT AS PER-MITTED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY TERMINATED.TERMThis license is effective only for so long as you own or lease the Product, unless earlier terminated. You may termi-nate this license at any time by destroying, at your expense, the Programs and related documentation together with all copies thereof in any form. This license will also terminate effective immediately upon occurrence of the conditions thereof set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein. Upon any such termination, you agree to destroy, at your expense, the Programs and related documentation together with all copies thereof in any form.YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT IT IS THE COMPLETE AND EXCLUSIVE STATE-MENT OF THE AGREEMENT BETWEEN US, WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT, ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MAT-TER OF THIS AGREEMENT.GOVERNMENT RESTRICTED RIGHTS.The Software is provided with “RESTRICTED RIGHTS.” Use duplication or disclosure by the government is subject to restrictions as set forth in FAR52.227-14 and DFAR252. 227-7013 et seq. or their successors.Use of the Software by the government constitutes acknowledgement of Intel’s proprietary rights therein.Contractor or Manufacturer is Intel Corporation, 2200 Mission College Blvd., Santa Clara, CA 95052.

28AppendixContrat de licence d’usage limitéLe(s) logiciel(s) (les “Logiciels”) fournis avec ce produit Panasonic (le “Produit”) sont exclusivement concédés en licence à l’utilisateur ultime (“vous”), et ils ne peuvent être utilisés que conformément aux clauses contractuelles cides-sous. En utilisant les logiciels, vous vous engagez de manière déﬁ nitive à respecter les termes, clauses et conditions des présentes.Panasonic Corporation a mis au point ou obtenu les Logiciels et vous en concède l’utilisation par les présentes. Vous assumez l’entière responsabilité du choix de ce Produit (y compris des Logiciels associés) pour obtenir les résultats escomptés, ainsi que de l’installation, de l’utilisation et des résultats obtenus.LicenceA. Panasonic Corporation vous octroie par les présentes le droit et la licence personnels, non cessibles et non exclu-sifs d’utiliser les Logiciels conformément aux termes, clauses et conditions de ce contrat. Vous reconnaissez ne recevoir qu’un droit limité d’utiliser les Logiciels et la documentation les accompagnant et vous vous engagez à n’obtenir aucun droit de titre, propriété ni aucun autre droit vis-à-vis des Logiciels et de la documentation les accom-pagnant ni vis-à-vis des algorithmes, concepts, dessins, conﬁ gurations et idées représentés par ou incorporés dans les Logiciels et la documentation les accompagnant, dont les titres, propriété et droits resteront tous à Panasonic Corporation ou à leurs propriétaires.B. Vous ne pouvez utiliser les Logiciels que sur le Produit unique qui est accompagné par les Logiciels.C. Vous et vos employés ou agents êtes requis de protéger la conﬁ dentialité des Logiciels. Vous ne pouvez ni dis-tribuer ni mettre les Logiciels et la documentation les accompagnant à la disposition d’un tiers, par partage de temps ou de quelque autre manière que ce soit, sans l’autorisation écrite préalable de Panasonic Corporation.D. Vous ne pouvez ni copier ni reproduire ni permettre la copie ni la reproduction des Logiciels ni de la documenta-tion les accompagnant pour quelque ﬁ n que ce soit, à l’exception d’une (1) copie des Logiciels à des ﬁ ns de sau-vegarde uniquement pour soutenir votre utilisation des Logiciels sur le Produit unique qui est accompagné par les Logiciels. Vous ne pouvez ni modiﬁ er ni tenter de modiﬁ er les Logiciels.E. Vous ne pouvez céder les Logiciels et en octroyer la licence à une autre partie qu’en rapport avec votre cession du Produit unique qui est accompagné par les Logiciels à cette autre partie. Au moment de cette cession, vous devez céder également toutes les copies, que ce soit sous forme imprimée ou lisible par la machine, de tous les Logiciels ainsi que de la documentation les accompagnant, à la même partie ou détruire les copies non cédées.F. Vous ne pouvez retirer aucune marque de droits d’auteur, marque de commerce ou autre ni aucune identiﬁ cation de produit des Logiciels et vous devez reproduire et inclure toutes ces notices ou identiﬁ cations de produit sur toutes les copies des Logiciels.Vous ne pouvez assembler en sens inverse, compiler en sens inverse ni retracer les Logiciels ni aucune de leurs cop-ies, de façon électronique ou mécanique, en tout ou en partie.Vous ne pouvez utiliser, copier, modiﬁ er, altérer ni céder les Logiciels ni aucune de leurs copies, en tout ou en partie, à l’exception de ce qui est expressément stipulé dans ce contrat.Si vous cédez la possession de toute copie ou de tout Logiciel à une autre partie, à l’exception de ce qui est autorisé au paragraphe E ci-dessus, votre licence est automatiquement résiliée.Termes, clauses et conditionsCette licence n’est effective que pour la durée de possession ou de crédit-bail du Produit, à moins d’une résiliation an-térieure. Vous pouvez résilier cette licence à tout moment en détruisant, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme que ce soit. Cette licence sera également résiliée, avec application immédiate, si les conditions de résiliation déﬁ nies ailleurs dans ce contrat se sont réalisées ou si vous ne respectez pas les termes, clauses et conditions qui y sont contenues. Au moment de la résiliation, vous acceptez de détruire, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme que ce soit.Vous reconnaissez avoir lu ce contrat, en avoir compris toute la substance et avoir accepté de respecter ses termes, clauses et conditions. Vous reconnaissez en outre qu’ils sont la description complète et exclusive du contrat conclu entre nous, contrat qui remplace et annule toute proposition ou contrat précédent, écrit ou oral, et toute autre commu-nication entre nous, relativement à l’objet du présent contrat.

29AppendixSpecicationsThis page provides the specications for the basic model. The model number is different according to the unit conguration.l To check the model number: Check the bottom of the computer or the box the computer came in at the time of purchase.l To check CPU speed, memory size and the hard disk drive (HDD) size: Run the Setup Utility (è Reference Manual “Setup Utility”) and select [Information] menu. [Processor Speed]: CPU speed, [Memory Size]: Memory size, [Hard Disk]: Hard disk drive sizen MainSpecicationsModel No. CF-31UFLAXDM CF-31SFLAXDMCPU/Secondary cache memory i5-3360M Processor (3 MB*1 cache, up to 3.5 GHz) with Intel® Turbo Boost Technologyi5-3320M Processor (3 MB*1 cache, up to 3.3 GHz) with Intel® Turbo Boost TechnologyChip Set Mobile Intel® QM77 Express ChipsetVideo controller AMD Radeon™ HD 7750M+Built in Chip Set (Built-in Chip Set)Main Memory*2 4 GB*1, DDR3L SDRAM (8 GB*1 Max.)Video Memory*1 *3 <32 bit> UMA (1785 MB Max.)<32 bit> UMA (1419 MB Max.)<64 bit> UMA (1696 MB Max.)512 MB dedicated –Hard Disk Drive 500 GB*4 (Serial ATA)Approx. 10 GB*4 is used as a partition with HDD recovery tools. (Users cannot use this partition.)Approx. 300 MB*4 is used as a partition with recovery tools. (Users cannot use this partition.)Display Method 13.1 XGA type (TFT) (1024 × 768 dots)Internal LCD 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots)*5External Display*6 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1280 × 768 dots/1280 × 1024 dots)Wireless LAN*7 Intel® Centrino® Advanced - N 6235 (è page 30)Bluetooth™*8 è page 30GPS*9 LR9101 (SirfStarIII)Wireless WAN*10 Sierra™ Wireless High-speed moduleLAN IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3ab 1000BASE-T(2nd LAN*11: IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX)Modem*12 Data: 56 kbps (V.92) FAX: 14.4 kbpsSound WAVE and MIDI playback, Intel® High Denition Audio subsystem supportSecurity Chip TPM (TCG V1.2 compliant)*13Card Slots PC Card Slot × 1, Type I or Type II, Allowable current 3.3 V: 400 mA, 5 V: 400 mAExpressCard Slot × 1, ExpressCard/34 or ExpressCard/54SD Memory Card Slot*14 × 1Contact Smart Card Slot*15 × 1RAM Module Slot × 1, DDR3L SDRAM, 204-pin, 1.35 V, SO-DIMM, PC3L-10600Interface USB ports 2.0 × 3, 3.0 × 1*16 / Serial Port (Dsub 9-pin male) / Modem Port (RJ-11)*12 / LAN Port (RJ-45) × 1*17 or × 2*11 / External Display Port (VGA) (Mini Dsub 15-pin female) / HDMI Port (Type A)*18 / IEEE1394a Interface Connector (4-pin)*19 / Microphone Jack (Miniature jack, 3.5 DIA) / Headphone Jack (Miniature jack, 3.5 DIA, Impedance 32 W, Output Power 4 mW × 2, Stereo) / Expansion Bus Connector (Dedicated 100-pin female)Keyboard / Pointing Device 87 keys / Touch Pad / Touchscreen*20Fingerprint Reader*21 Array Size : 192 × 4 pixels, Image Size : 192 × 512 pixels, Image Resolution : 508 DPIWeb Camera*22 640 × 480 dots, 30 fpsPower Supply AC adaptor or Battery packAC Adaptor*23 Input: 100 V to 240 V AC, 50 Hz/60 Hz, Output: 15.6 V DC, 7.05 ACF-31 Appendix.indd 29 2012/04/26 16:51:37

30Appendix Main Speciﬁ cationsModel No. CF-31UFLAXDM CF-31SFLAXDMBattery Pack Li-ion 10.65 V, Typical 8550 mAh / Minimum 8100 mAhOperating Time*24 Main Battery: Approx. 12.0 hours Main Battery: Approx. 14.5 hours-Main Battery + Second Battery*25: Approx. 21.0 hoursCharging Time*26Power on Main Battery: Approx. 4.5 hours-Main Battery + Second Battery*25: Approx. 8.0 hoursPower off Main Battery: Approx. 3.5 hours-Main Battery + Second Battery*25: Approx. 7.0 hoursPower Consumption*27 Approx. 55 W*28 / Approx. 100 W (maximum when recharging in the ON state) Approx. 45 W*28 / Approx. 100 W (maximum when recharging in the ON state)Physical Dimensions (W × D × H)(including the carrying handle) 302 mm × 292 mm × 73.5 mm {11.9" × 11.5" × 2.9"}Weight (including the hand strap) Approx. 3.72 kg {Approx. 8.2 lb.}EnvironmentOperating Temperature -10 °C to 50 °C {14 °F to 122 °F} (IEC60068-2-1, 2)*29Humidity 30 % to 80 % (No condensation)Storage Temperature -20 °C to 60 °C {-4 °F to 140 °F}Humidity 30 % to 90 % RH (No condensation) SoftwareInstalled OS*30 Genuine Windows® 7 Professional 32-bit Service Pack 1 / Genuine Windows 7 Professional 64-bit Service Pack 1Pre-installed Software*30Adobe Reader, PC Information Viewer, Display Selector, Bluetooth™ Stack for Windows® by TOSHI-BA*8, Wireless Switch Utility, Intel® PROSet / Wireless Soft ware*7, Wireless Connection Disable Util-ity*31, Hotkey Settings, Battery Recalibration Utility, Inﬁ neon TPM Professional Package*13 *31, Protector Suite*21 *31, Aptio Setup Utility, Hard Disk Data Erase Utility*32, PC-Diagnostic Utility, Wireless Manager Mobile Edition 5.5f *31 *33, Quick Boot Manager, Fan Monitoring Utility, Dashboard for Panasonic PC, GPS Viewer*9, Camera Utility*22, System Interface Manager, Video switch Utility, External Antenna Set-ting Utility, Wireless Antenna switch Utility, Recovery Disc Creation Utility, Power Plan Extension Utility Wireless LAN*7Data Transfer Rates IEEE802.11a : 54/48/36/24/18/12/9/6 Mbps (automatically switched)*34IEEE802.11b : 11/5/2/1 Mbps (automatically switched)*34IEEE802.11g : 54/48/36/24/18/12/9/6 Mbps (automatically switched)*34IEEE802.11n*35 : (HT20) GI*36 = 400ns: 144/130/115/86/72/65/57/43/39/28/21/14/7 Mbps (automatically switched)*34 GI*36 = 800ns: 130/117/104/78/65/58/52/39/26/19/13/6 Mbps(automatically switched)*34 (HT40) GI*36 = 400ns: 300/270/240/180/157/135/120/90/60/30/15 Mbps (automatically switched)*34 GI*36 = 800ns: 270/243/216/162/135/121/108/81/54/40/27/13 Mbps (automatically switched)*34Standards Supported IEEE802.11a / IEEE802.11b / IEEE802.11g / IEEE802.11nTransmission method OFDM system, DSSS systemWireless Channels Used IEEE802.11a : Channels 36/40/44/48/52/56/60/64/100/104/108/112/116/132/136/140/149/153/157/161/165IEEE802.11b/IEEE802.11g : Channels 1 to 11IEEE802.11n : Channels 1-11/36/40/44/48/52/56/60/64/100/104/108/112/116/132/136/140/149/153/157/161/165RF Frequency Band IEEE802.11a : 5.18 GHz - 5.32 GHz, 5.5 GHz - 5.7 GHz, 5.745 GHz - 5.825 GHzIEEE802.11b/IEEE802.11g : 2.412 GHz - 2.462 GHzIEEE802.11n : 2.412 GHz - 2.462 GHz, 5.18 GHz - 5.32 GHz, 5.5 GHz - 5.7 GHz, 5.745 GHz -5.825 GHz BluetoothTM*8Bluetooth Version version 4.0Classic model / Low Energy modelTransmission method FHSS systemWireless Channels Used Channel 1 to 79 / Channel 0 to 39RF Frequency Band 2.402 GHz - 2.480 GHzSpeciﬁ cations

$31Appendix*1 1 MB = 1,048,576 bytes /1 GB = 1,073,741,824 bytes*2 Memory size of the factory default depends on the model. You can physically expand the memory up to 8 GB, but the total amount of usable memory available will be less depending on the actual system conﬁ guration.*3 A segment of the main memory is allotted automatically depending on the computer’s operating status. The size of the Video Memory cannot be set by the user. *4 1 MB = 1,000,000 bytes / 1 GB = 1,000,000,000 bytes. Your operating system or some application software will report as fewer MB/GB.*5 A 16,777,216 color display is achieved by using the dithering function.*6 Display may be impossible using some connected external displays.*7 Only for model with wireless LAN.*8 Only for model with Bluetooth.*9 Only for model with GPS.*10 Only for model with wireless WAN.*11 Only for model with 2nd LAN.*12 Only for model with modem.*13 Only for model with TPMFor information on TPM, refer to the Installation Manual of “Trusted Platform Module (TPM)” by the following procedure. Click (Start) and input “c:\util\drivers\tpm\index.hta” in [Search programs and ﬁ les] and press Enter. *14 This slot is compatible with High-Speed Mode. Operation has been tested and conﬁ rmed using Panasonic SD/SDHC/SDXC Memory Cards with a capacity of up to 64 GB. Operation on other SD equipment is not guaranteed.*15 Only for model with Smart Card slot.*16 Does not guarantee operation of all USB-compatible peripherals.*17 Only for model without 2nd LAN.*18 Does not guarantee operation of all HDMI-compatible peripherals.*19 Only for model with IEEE 1394a interface.*20 Only for model with Touchscreen.*21 Only for model with Fingerprint reader.*22 Only for model with Web Camera.*23 <Only for North America> The AC adaptor is compatible with power sources up to 240 V AC adaptor. This computer is supplied with a 125 V AC compat-ible AC cord. 20-M-2-1*24 Measured with LCD brightness : 60 cd/m2 Varies depending on the usage conditions, or when an optional device is attached.*25 Only for model with 2nd Battery.*26 Varies depending on the usage conditions, CPU speed, etc.*27 Approx. 0.5 W when the battery pack is fully charged (or not being charged) and the computer is off. <When using with 115 V AC> Even when the AC adaptor is not connected to the computer, power is consumed (Max. 0.2 W) simply by having the AC adaptor plugged into an AC outlet.*28 Rated power consumption. 23-E-1*29 Do not expose the skin to this product when using the product in a hot or cold environment. ( page 10)When using in hot or cold environment, some peripherals may fail to work properly. Check the operation environment of the peripherals.Using this product continuously in a hot environment will shorten the product life. Avoid use in these types of environments.When using in low temperature environment, startup may become slow or battery operation time may become short. The com-puter consumes power when the hard disk is warming up during startup. Therefore, if you are using battery power and the remaining power is low, the computer may not start up.*30 When reinstalling Windows using the data of the recovery area on the hard disk, you can select the OS to be installed (either Windows 7 (32-bit) or Windows 7 (64-bit)). An OS that has been installed at the time of purchase or an OS that has been in-stalled using the hard disk recovery function or the recovery disc can be supported.*31 Must be installed before use.*32 Perform on the recovery partition. (If this software can not be performed on the recovery partition, perform from the recovery disc)*33 For information on Wireless Manager, refer to the “Supplementary Instructions for Wireless Manager mobile edition 5.5” by the following procedure. Click (Start) and input “c:\util\wlprjct\Supplementary Instructions.pdf” in [Search programs and ﬁ les] and press Enter.*34 These are speeds speciﬁ ed in IEEE802.11a+b+g+n standards. Actual speeds may differ.*35 Available when set to “WPA-PSK”, “WPA2-PSK” or “none”.*36 Only available when HT40 enabled by the computer and access point which associated supports HT40.$

Panasonic of North America 9TGWL12A Intel Centrino Advanced-N 6235 User Manual

Panasonic Corporation of North America Intel Centrino Advanced-N 6235

Contents

User manual

Navigation menu

Namespaces

Views

Navigation