Panasonic of North America 9TGWL12B 1x1 802.11 b/g/n PCle Module User Manual DFQW5645ZAT CF 53mk2 7 OI M

Panasonic Corporation of North America 1x1 802.11 b/g/n PCle Module DFQW5645ZAT CF 53mk2 7 OI M

UserManual.wiki >

Panasonic of North America >

9TGWL12B User Manual

User manual

Please read these instructions carefully before using this product, and save this manual for future use.ContentsGetting StartedUseful InformationGetting StartedUseful InformationTroubleshootingAppendixAppendixTroubleshootingOPERATING INSTRUCTIONSPersonal ComputerModel No. CF-53 seriesIntroduction.................................................2Read Me First ..............................................3(Precautions)Description of Parts .....................................11First-time Operation .....................................13On-screen Manual.......................................17Handling and Maintenance.............................18Reinstalling Software....................................20Troubleshooting (Basic) ................................22LIMITED USE LICENSE AGREEMENT..............26Specifications ............................................28LIMITED WARRANTY ..................................32For further information about the com-puter, you can refer to the on-screen manual.To access the on-screen manual Îpage 17 “On-screen Manual”DFQW5645ZAT_CF-53mk2_7_OI_M.book 1 ページ２０１２年５月８日　火曜日　午後６時１１分

3Getting StartedUseful InformationTroubleshootingAppendixRead Me First<Only for model with modem>When using your telephone equipment, basic safety precau-tions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.3. Do not use the telephone to report a gas leak in the vicinity of the leak.4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.SAVE THESE INSTRUCTIONS19-E-1Certaines mesures de sécurité doivent être prises pen-dant l’utilisation de matérial téléphonique afin de réduire les risques d’incendie, de choc électrique et de blessures. En voici quelquesunes:1. Ne pas utiliser l’appareil près de l’eau, p.ex., près d’une baignoire, d’un lavabo, d’un évier de cuisine, d’un bac à laver, dans un sous-sol humide ou près d’une piscine.2.Éviter d’utiliser le téléphone (sauf s’il s’agit d’un appareil sans fil) pendant un orage électrique. Ceci peut présenter un risque de choc électrique causé par la foudre.3. Ne pas utiliser l’appareil téléphonique pour signaler une fuite de gaz s’il est situé près de la fuite.4.Utiliser seulement le cordon d’alimentation et le type de piles indiqués dans ce manual. Ne pas jeter les piles dans le feu: elles peuvent exploser. Se conformer aux règlements pertinents quant à l’élimination des piles.CONSERVER CES INSTRUCTIONS19-F-1<Only for model with wireless LAN>This product and your HealthThis product, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this product however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.Because this product operates within the guidelines found in radio frequency safety standards and recommendations, we believe this product is safe for use by consumers. These stan-dards and recommendations reflect the consensus of the scien-tific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.In some situations or environments, the use of this prod-uct may be restricted by the proprietor of the building or responsible representatives of the organization. These sit-uations may for example include:zUsing this product on board of airplanes, orzIn any other environment where the risk of interference to other devices or services is perceived or identified as harmful.If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authoriza-tion to use this product prior to turning on the product.Regulatory InformationWe are not responsible for any radio or television interfer-ence caused by unauthorized modification of this product. The correction of interference caused by such unauthor-ized modification will be the responsibility of the user. We and its authorized resellers or distributors are not liable for damage or violation of government regulations that may arise from failing to comply with these guidelines.26-M-1<Uniquement les modèles avec réseau local sans fil et/ou Bluetooth>Ce produit et votre santéCe produit, comme tout autre appareil radio, émet de l’énergie radioélectrique. Toutefois, la quantité d’énergie émise par ce produit est beaucoup moins importante que l’énergie radioélectrique émise par des appareils sans fil tels que les téléphones portables. L’utilisation de ce produit ne comporte aucun risque pour le consommateur du fait que cet appareil opère dans les limites des direc-tives concernant les normes et les recommandations de sécurité sur les fréquences radio. Ces normes et recom-mandations reflètent le consensus de la communauté sci-entifique et résultent de délibérations de jurys et comités de scientifiques qui examinent et interprètent continuelle-ment les nouveautés de la vaste littérature sur les recher-ches effectuées. Dans certaines situations ou environnements, l’utilisation de ce produit peut être restreinte par le propriétaire du bâtiment ou par les représentants responsables de l’organisation. Ces situa-tions peuvent être les suivantes par exemple :zA bord d’un avion, ouzDans tout autre environnement où les risques d’inter-férence sur d’autres appareils ou services sont perçus ou identifiables comme dangereux.Si vous n’êtes pas sûr de la réglementation applicable à l’utilisation d’appareils sans fil dans une organisation ou un environnement spécifique, (par exemple dans un aéro-port) nous vous invitons àdemander l’autorisation d’util-iser ce produit avant sa mise en marche.Informations concernant la réglementationNous déclinons toute responsabilité pour toute inter-férence radio ou télévision causée par des modifications non autorisées apportées à ce produit. La correction d’interférences causées par de telles modifications non autorisées sera la seule responsabilité de son utilisateur. Nousmêmes, les revendeurs officiels et les distributeurs ne sommes pas responsable de tout dégât ou de toute violation des règlements de l’État pouvant découler du non-respect de ces directives.26-F-1Important Safety Instructions/ Importantes Mesures De SecuriteInformation to the UserDFQW5645ZAT_CF-53mk2_7_OI_M.book 3 ページ２０１２年５月８日　火曜日　午後６時１１分

4Read Me FirstGetting StartedUseful InformationTroubleshootingAppendixLithium Battery!This computer contains a lithium battery to enable the date, time, and other data to be stored. The battery should only be exchanged by authorized service personnel.Warning! A risk of explosion from incorrect installation or misapplication may possibly occur.15-E-1Pile au lithium!Le micro-ordinateur renferme une pile au lithium qui permet de sauvegarder certaines données, notamment la date et l’heure. La pile ne doit être remplacée que par un technicien qualifié.Danger ! Risque d’explosion en cas de non respect de cette mise en garde!15-F-1CAUTION!THIS PRODUCT UTILIZES A LASER.USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.REFER SERVICING TO QUALIFIED PERSONNEL.12-E-1AVERTISSEMENT!CET APPAREIL UTILISE UN LASER.L’UTILISATION DE COMMANDES OU DE RÉGLAGES OU L’EXÉ-CUTION DE PROCÉDURES AUTRES QUE CELLES SPÉCIFIÉES ICI PEUVENT PROVOQUER UNE EXPOSITION À DES RADIA-TIONS DANGEREUSES.NE PAS OUVRIR LES COUVERCLES NI ESSAYER DE RÉPARER SOIMÊME.CONFIER TOUT TRAVAIL D’ENTRETIEN À UN PERSONNEL QUALIFIÉ.12-F-1The following label is put on the bottom of the computer.These symbols are only valid in the European Union. If you wish to dis-card this product, please contact your local authorities or dealer and ask for the correct method of dis-posal.53-M-1<Only for model with wireless WAN>The following safety precautions must be observed during all phases of the operation, usage, service or repair of any Personal Computer or Handheld Computer incorporating wireless WAN modem. Manufacturers of the cellular ter-minal are advised to convey the following safety informa-tion to users and operating personnel and to incorporate these guidelines into all manuals supplied with the prod-uct. Failure to comply with these precautions violates safety standards of design, manufacture and intended use of the product. Panasonic assumes no liability for customer failure to comply with these precautions.When in a hospital or other health care facility, observe the restrictions on the use of mobiles. Switch Personal Computer or Handheld Computer incorporating wireless WAN modem off, if instructed to do so by the guidelines posted in sensitive areas. Medical equipment may be sensitive to RF energy.The operation of cardiac pacemakers, other implanted medical equipment and hearing aids can be affected by interference from Personal Computer or Handheld Computer incorporating wireless WAN modem placed close to the device. If in doubt about potential danger, contact the physician or the manu-facturer of the device to verify that the equipment is properly shielded. Pacemaker patients are advised to keep their Personal Computer or Handheld Com-puter incorporating wireless WAN modem away from the pacemaker, while it is on.Switch off Personal Computer or Handheld Com-puter incorporating wireless WAN modem before boarding an aircraft. Make sure it cannot be switched on inadvertently. The operation of wireless appli-ances in an aircraft is forbidden to prevent interfer-ence with communications systems. Failure to observe these instructions may lead to the suspen-sion or denial of cellular services to the offender, legal action, or both.For details on usage of this unit in aircrafts please consult and follow instruction provided by the airline.Do not operate Personal Computer or Handheld Computer incorporating wireless WAN modem in the presence of flammable gases or fumes. Switch off the cellular terminal when you are near petrol sta-tions, fuel depots, chemical plants or where blasting operations are in progress. Operation of any electri-cal equipment in potentially explosive atmospheres can constitute a safety hazard.Your Personal Computer or Handheld Computer incorporating wireless WAN modem receives and transmits radio frequency energy while switched on. Remember that interference can occur if it is used close to TV sets, radios, computers or inadequately shielded equipment. Follow any special regulations and always switch off Personal Computer or Hand-held Computer incorporating wireless WAN modem wherever forbidden, or when you suspect that it may cause interference or danger.Lithium Battery / Pile au lithiumCD/DVD Drive Caution / Précautions pour le lecteur CD/DVDInformation for Users on Collection and Disposal of Old Equipment and used BatteriesSafety PrecautionsDFQW5645ZAT_CF-53mk2_7_OI_M.book 4 ページ２０１２年５月８日　火曜日　午後６時１１分

5Getting StartedUseful InformationTroubleshootingAppendixRoad safety comes fi rst! Do not use a Personal Computer or Handheld Computer incorporating wire-less WAN modem while driving a vehicle. Do not place the computer with wireless WAN modem in an area where it could cause personal injury to the driver or passengers. It is recommended to stow the unit in the boot or secure stowage area while driving. Do not place the computer with wireless WAN modem in an area over an air bag or in the vicinity where an air bag may deploy.Air bags infl ate with great force and if the computer with wireless WAN modem is placed in the air bag deployment area may be propelled with great force and cause serious injury to occupants of the vehicle.IMPORTANT!Personal Computer or Handheld Computer incorpo-rating wireless WAN modem operate using radio sig-nals and cellular networks cannot be guaranteed to connect in all conditions. Therefore, you should never rely solely upon any wireless device for essen-tial communications, for example emergency calls.Remember, in order to make or receive calls, Per-sonal Computer or Handheld Computer incorporat-ing wireless WAN modem must be switched on and in a coverage area with adequate cellular signal strength.Some networks do not allow for emergency calls if certain network services or phone features are in use (e.g. lock functions, fixed dialing etc.). You may need to deactivate those features before you can make an emergency call.Some networks require that a valid SIM card be properly inserted in Personal Computer or Handheld Computer incorporating wireless WAN modem.Federal Communications Commission Radio Fre-quency Interference StatementNote: This equipment has been tested and found to com-ply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-ence in a residential installation. This equipment gener-ates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep-tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:zReorient or relocate the receiving antenna.zIncrease the separation between the equipment and receiver.zConnect the equipment into an outlet on a circuit differ-ent from that to which the receiver is connected.zConsult the Panasonic Service Center or an experi-enced radio/TV technician for help.WarningTo assure continued compliance, use only shielded inter-face cables when connecting to a computer or peripheral.Also, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired oper-ation.FCC RF Exposure Warning:zThis equipment is provided with PC Card slot that could be used with wireless transmitters, which will be specif-ically recommended when they become available.Other third-party wireless transmitters have not been RF exposure evaluated for use with this computer and may not comply with FCC RF exposure requirements.<Only for model with wireless LAN/Bluetooth>zThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.zThis equipment has been approved for mobile opera-tion, and unless otherwise advised in separate supple-mental instructions for individual wireless transmitter(s), requires minimum 20cm spacing be pro-vided between antenna(s) and all person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.zThis equipment may not be co-located or operated with any other antenna or transmitter.25-M-6<Only for model with wireless LAN>This product is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range.FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful inter-ference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this product.25-M-W-6Responsible Party: Panasonic Corporation of North Amer-ica One Panasonic WaySecaucus, NJ 07094Tel No:1-800-LAPTOP5 (1-800-527-8675)6-M-1<Only for model with modem>FCC Regulation Notice for modemThis equipment contains a FCC approved modem.1. This equipment complies with CFR47 Part 68 rules.On the computer is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If required, this information must be provided to the tele-phone company.2. An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. See Installation Instruc-tions for details.Models for U.S.A.DFQW5645ZAT_CF-53mk2_7_OI_M.book 5 ページ２０１２年５月８日　火曜日　午後６時１１分

6Read Me FirstGetting StartedUseful InformationTroubleshootingAppendix3.The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all area, the sum of RENs should not exceed five (5.0). To be certain of the num-ber of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.4.If your telephone equipment cause harm to the telephone network, the telephone company will notify you in advice that temporary discontinuance of service may be required. But if advice notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.5. The telephone company may take changes in its facili-ties, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.6.If trouble is experienced with this equipment, for repair or warranty information, please contact Panasonic Corporation of North America at DIAL TOLL FREE 1-800-LAPTOP5 (1-800-527-8675). If the equipment is causing harm to the tele-phone network, the telephone company may request that you disconnect the equipment until the problem is resolved.7. There are no user serviceable parts contained in this equipment.8. This equipment may not be used on coin service pro-vided by the telephone company. Connection to party lines is subject to state tariffs.9.The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entry, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. In order to pro-gram this information into your fax software, you should refer to the manual of the Fax software being used.10.According to the FCC’s electrical safety advisory, we recommend that you may install an AC surge arrestor in the AC outlet to which this equipment is connected.Telephone companies report that electrical surges, typ-ically lightning transients, are very destructive to cus-tomer terminal equipment connected to AC power sources and that this is a major nationwide problem.“Caution : To reduce the risk of fire, use only No.26 AWG or larger (e.g., 24 AWG) UL listed or CSA certified tele-communication line cord.”“ATTENTION : Pour réduire le risque d’incendie, utiliser uniquement des conducteurs de télécommunications 26 AWG ou de section supérieure (p. ex. 24 AWG) UL énu-mérés ou CSA certifié.”16-M-1FCC RF Exposure Warning:This equipment is provided with external antenna connec-tor(s) for connection to optional Car Mounter or Port Rep-licator for mobile external mounted antenna(s). External antenna(s) must be professionally installed and cannot exceed recommended maximum antenna gain as described in individual provided supplement instructions for wireless transmitters. The Car Mounter is provided with Radiall/Larsen WLAN whip antenna, type NMO5E2400BKTNC with 5 dBi antenna gain. Also, user must maintain minimum 20 cm spacing between external antenna(s) and all person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.32-M-1For U.S.A.-California Only<Only for model with modem>Industry Canada (IC) Notice for modemThis equipment contains an Industry Canada approved modem unit.The Industry Canada label is affixed on the modem unit.EQUIPMENT ATTACHEMENT LIMITATIONS“NOTICE: The Industry Canada label identifies certified equipment.This certification means that the equipment meets tele-communications network protective, operational and safety requirements as prescribed in the appropriate Ter-minal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connec-tion. The customer should be aware that compliance with the above conditions may not prevent degradation of ser-vice in some situations.Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.Users should ensure for their own protection that the elec-trical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particu-larly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.”“NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be con-nected to a telephone interface.The termination on an interface may consist of any combi-nation of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.”REN: See bottom of the computerUSA Only: Disposal may be regulated in your commu-nity due to environmental considerations. For disposal or recycling information, please visit Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149 65-M-2This product contains a CR Coin Cell Lithium Bat-tery which contains Perchlorate Material – special handling may apply.See www.dtsc.ca.gov/hazardouswaste/perchlorate/38-M-1Models for CanadaDFQW5645ZAT_CF-53mk2_7_OI_M.book 6 ページ２０１２年５月８日　火曜日　午後６時１１分

7Getting StartedUseful InformationTroubleshootingAppendixRESTRICTIONS CONCERNANT LE RACCORDEMENTDE MATÉRIEL“AVIS: L’étiquette d’Industrie Canada identifie le matériel homologué.Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’entreprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de raccordement.L’abonné ne doit pas oublier qu’il est possible que la con-formité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations.Les réparations de matériel homologué doivent être coor-données par un représentant désigné par le fournisseur.L’entreprise de télécommunications peut demander à l’utilisateur de débrancher un appareil à la suite de répa-rations ou de modifications effectuées par l’utilisateur ou à cause de mauvais fonctionnement.Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’énergie élec-trique, des lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales. Avertissement: L’utilisateur ne doit pas tenter de faire ces raccordements luimême; il doit avoir recours à un service d’inspection des installationsélectriques, ou à un électricien, selon le cas.”“AVIS: L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de touts les dispositifs n’excède pas 5.”IES: Voir sous le fond de l’ordinateur17-Ca-1Canadian ICES-003This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.7-M-2<Only for model with wireless LAN/Bluetooth>Industry CanadaOperation is subject to the following two conditions;(1) this device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesired operation of the device.<Ne s’applique qu’aux modèles avec technologie Blue-tooth/LAN sans fil/WAN sans fil>Industrie CanadaCet équipement est conforme à la norme CNR-210 d’Industrie Canada. Son fonctionnement estsoumis aux deux conditions suivantes :(1) ce dispositif ne peut produire de brouillage, et(2) ce dispositif doit accepter le brouillage, y compris le brouillage pouvant entraîner le fonctionnement non désiré de l’appareil.30-Ca-1-1<Only for model with wireless LAN>This product (local network devices) for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems.High power radars are allocated as primary users (mean-ing they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LELAN devices.<Ne s’applique qu’aux modèles avec technologie LAN sans fil>Cet appareil (pour réseaux locaux radioélectriques) dans les bandes de fréquences 5150-5250 MHz est réservé à une utilisa-tion à l’intérieur afin de réduire le risque d’interférence avec les systèmes satellites mobiles bicanaux.Les radars forte puissance sont désignés comme étant les pre-miers utilisateurs (c’est-à-dire qu’ils ont la priorité) des bandes de fréquences 5250-5350 MHz et 5650-5850 MHz. Ces stations radarspeuvent provoquer des interférences et/ou des dom-mages à ce périphérique.30-Ca-2-1This device has been designed to operate with the Radiall/Lar-sen whip antenna, type NMO5E2400BKTNC WLAN antenna having a maximum gain of 5 dBi. A WLAN Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The Required antenna impedance is 50 ohms.To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication.Cet appareil est conçu pour opérer avec l’antenne-fouet Radiall/Larsen, type WLAN NMO5E2400BKTNC, ayant un gain maximum de 5 dB. Les règlements d’Industrie Canada interdisent l’utilisation d’une antenne WLAN dont le gain serait supérieur à cette limite. L’antenne doit avoir une impédance de 50 ohms.Afin de réduire le risque d’interférence radioélectrique aux autres utilisateurs des bandes de fréquences, le type d’antenne et son gain doivent être tels que la puissance iso-trope rayonnée équivalente (PIRE) n’est pas plus élevée que le niveau requis pour assurer la communication.25-Ca-1-1<Only for model with wireless LAN/Bluetooth>*This equipment complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment.*This equipment has been approved for mobile operation, and unless otherwise advised in separate supplemental instructions for individual wireless transmitter(s), requires minimum 20 cm spacing be provided between antenna(s) and all person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.<Ne s’applique qu’aux modèles avec technologie Blue-tooth/LAN sans fil/WAN sans fil>* Cet équipement est conforme aux limites d’exposition aux rayonnements d’Industrie Canada établies pour un environnement non contrôlé.* Cet équipement a été approuvé à des fins d’opération mobile et, sauf indication contraire, dans une notice supplémentaire concernant les émetteurs sans fil indi-viduels, doit être utilisé en veillant qu’il y ait une dis-tance d’au moins 20 cm entre son(ses) antenne(s) et le corps de l’utilisateur (sauf les extrémités : mains, poignets et pieds) dans les modes d’opération sans fil.DFQW5645ZAT_CF-53mk2_7_OI_M.book 7 ページ２０１２年５月８日　火曜日　午後６時１１分

8Read Me FirstGetting StartedUseful InformationTroubleshootingAppendix<Only for model with a “CE” mark on the bottom of the computer>Declaration of Conformity (DoC)“Hereby, Panasonic declares that this Personal Computer is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC.”Hint:If you want to get a copy of the original DoC of our above mentioned products, please contact our web address: http://www.doc.panasonic.de Authorised Representative:Panasonic Testing CentrePanasonic Marketing Europe GmbHWinsbergring 15, 22525 Hamburg, GermanyNetwork connection of Wired Modem.The terminal equipment is intended for connection to the follow-ing public network;In all the countries of European Economical Area and Turkey;- Public Switched Telephony NetworksTechnical Features of Wired Modem.The terminal equipment includes the following features;- DTMF dialing- Maximum bitrate receiving mode: 56 kbit/s- Maximum bitrate sending mode: 33.6 kbit/s18-E-1This computer is not intended for use in medical equip-ment including life-support systems, air traffic control sys-tems, or other equipment, devices or systems that are involved with ensuring human life or safety. Panasonic cannot be held responsible in any way for any damages or loss resulting from the use of this unit in these types of equipment, devices or systems, etc.This computer has been designed so as to minimize shock to the LCD and hard disk drive, the leakage of liq-uid (e.g., water) on to the keyboard, etc., but no warranty is provided against such trouble. Therefore, as a precision instrument, be extremely careful in the handling.If a Malfunction or Trouble Occurs, Immediately Stop UseIf a Malfunction Occurs, Immediately Unplug the AC Plug and the Battery Pack• This product is damaged• Foreign object inside this product• Smoke emitted• Unusual smell emitted• Unusually hotContinuing to use this product while any of the above con-ditions are present may result in fire or electric shock.•If a malfunction or trouble occurs, immediately turn the power off and unplug the AC plug, and then remove the battery pack. Then contact your technical support office for repair.Do Not Touch This Product In a Thunderstorm If Con-nected with the AC Cable or Any Other CablesElectric shock may result.Do Not Connect the AC Adaptor to a Power SourceOther Than a Standard Household AC OutletOtherwise, a fire due to overheating may result. Connecting to a DC/AC converter (inverter) may damage the AC adaptor. On an airplane, only connect the AC adaptor/charger to an AC outlet specifically approved for such use.FOR USE WITH MODEL NO. : CF-AA5713APOUR UTILISER AVEC MODÈLE : CF-AA5713A 20-Ca-1Models for EuropePrecautionsTHIS PRODUCT IS NOT INTENDED FOR USE AS, OR AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS, AIR TRAF-FIC CONTROL EQUIPMENT/SYSTEMS, AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS *1, MEDICAL DEVICES OR ACCESSORIES*2, LIFE SUPPORT SYSTEMS OR OTHER EQUIPMENTS/DEVICES/SYSTEMS THAT ARE INVOLVED WITH ENSURING HUMAN LIFE OR SAFETY. PANASONIC WILL NOT BE RESPONSIBLE FOR ANY LIABILITY RESULTING FROM THE USE OF THIS PROD-UCT ARISING OUT OF THE FOREGOING USES.*1 AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include Class2 Electrical Flight Bag (EFB) Systems and Class1 EFB Systems when used during critical phases of flight (e.g., during take-off and landing) and/or mounted on to the aircraft. Class1 EFB Systems and 2 EFB Systems are defined by FAA: AC (Advisory Circular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaflets) No.36.*2 As defined by the European Medical Device Directive (MDD) 93/42/EEC.Panasonic cannot guarantee any specifications, tech-nologies, reliability, safety (e.g. Flammability/Smoke/Toxicity/Radio Frequency Emission, etc) requirements related to aviation standards and medical equipment standards that differ from the specifications of our COTS (Commercial-Off-The-Shelf) products.DFQW5645ZAT_CF-53mk2_7_OI_M.book 8 ページ２０１２年５月８日　火曜日　午後６時１１分

9Getting StartedUseful InformationTroubleshootingAppendixDo Not Do Anything That May Damage the AC Cord,the AC Plug, or the AC AdaptorDo not damage or modify the cord, place it near hot tools, bend, twist, or pull it forcefully, place heavy objects on it, or bundle it tightly.Continuing to use a damaged cord may result in fire, short circuit, or electric shock.Do Not Pull or Insert the AC Plug If Your Hands Are WetElectric shock may result.Clean Dust and Other Debris of the AC Plug RegularlyIf dust or other debris accumulates on the plug, humidity, etc. may cause a defect in the insulation, which may result in a fire.• Pull the plug, and wipe it with a dry cloth.Pull the plug if the computer is not being used for a long period of time.Insert the AC Plug CompletelyIf the plug is not inserted completely, fire due to overheat-ing or electric shock may result.• Do not use a damaged plug or loose AC outlet.Do Not Place Containers of Liquid or Metal Objects onTop of This ProductIf water or other liquid spills, or if paper clips, coins, or foreign matter get inside this product, fire or electric shock may result.•If foreign matter has found its way inside, immediately turn the power off and unplug the AC plug and remove the bat-tery pack. Then contact your technical support office.Do Not Disassemble This ProductThe high-voltage areas inside may give you an electric shock, or foreign matter may enter and result in a fire.Keep SD Memory Cards Away from Infants and SmallChildrenAccidental swallowing will result in bodily injury.•In the event of accidental swallowing, see a doctor immediately.Do Not Place This Product on Unstable SurfacesIf balance is lost, this product may fall over or drop, result-ing in an injury.Avoid StackingIf balance is lost, this product may fall over or drop, result-ing in an injury.Do Not Leave This Product in High Temperature Envi-ronment for a Long Period of TimeLeaving this product where it will be exposed to extremely high temperatures such as near fire or in direct sunlight may deform the cabinet and/or cause trouble in the inter-nal parts. Continued use in such a resulting condition may lead to short-circuiting or insulation defects, etc. which may in turn lead to a fire or electric shocks.Do Not Block the Ventilation Hole (Exhaust)Using this product wrapped in cloth or on top of bedding or a blanket can block the ventilation hole and cause heat to build up inside, possibly resulting in a fire.Hold the Plug When Unplugging the AC PlugPulling on the cord may damage the cord, resulting in a fire or electric shock.Do Not Move This Product While the AC Plug Is ConnectedThe AC cord may be damaged, resulting in fire or electric shock.• If the AC cord is damaged, unplug the AC plug immedi-ately.Use Only the Specified AC Adaptor With This ProductUsing an AC adaptor other than the one supplied (sup-plied with the unit or one sold separately as an accessory) may result in a fire.Do Not Subject the AC Adaptor to Any Strong ImpactUsing the AC adaptor after a strong impact such as being dropped may result in electric shock, short circuit, or fire.Take a Break of 10-15 Minutes Every HourUsing this product for long periods of time may have detri-mental health effects on the eyes or hands.Do Not Look into the CD/DVD DriveLooking directly at the internal laser light source may result in damage to eyesight.Do Not Use Discs That Are Cracked or DeformedBecause the discs rotate at high speeds, damaged discs may break apart causing injury.• Discs that are not round and discs that have been repaired using adhesives are similarly dangerous, and so should not be used.Do Not Turn the Volume Up to Loud When UsingHeadphonesListening at high volumes that overstimulate the ear for long periods of time may result in loss of hearing.Do Not Connect a Telephone Line, or a Network CableOther Than the One Specified, into the LAN PortIf the LAN port is connected to a network such as the ones listed below, a fire or electric shock may result.• Networks other than 1000BASE-T, 100BASE-TX or 10BASE-T• Phone lines (IP phone (Internet Protocol Telephone), Telephone lines, internal phone lines (on-premise switches), digital public phones, etc.)Do Not Use With Exposing the Skin to This ProductFor a Long Period of TimeUsing this product with exposing the skin to the heat source of this product or AC adaptor for a long period of time can cause a low-temperature burn.Do not expose yourself to the hot wind from the venti-lation hole (exhaust) for a long period of time.Low-temperature burns may result.Covering the ventilation hole (exhaust) with your hand or other object can cause heat to build up inside, possibly resulting in burns.Do Not Expose the Skin To This Product When Usingthe Product In A Hot Or Cold Environment.Burns, low-temperature burns, or frostbite may result.• When it is necessary to expose the skin to this product such as to scan a fingerprint, perform the operation in the shortest time possible.<Only for model with modem>Use the Modem With a Regular Telephone LineConnection to an internal phone line (on-premise switches) of a company or business office, etc. or to a dig-ital public phone or use in a country or area not supported by the computer may result in a fire or electric shocks.zDo not place the computer near a television or radio receiver.zKeep the computer away from magnets. Data stored on the hard disk may be lost.zThis computer is not intended for the display of images for use in medical diagnosis.zThis computer is not intended for a use with connection of medical equipment for the purpose of medical diagnosis.zPanasonic shall not be liable for loss of data or other incidental or consequential damages resulting from the use of this product.DFQW5645ZAT_CF-53mk2_7_OI_M.book 9 ページ２０１２年５月８日　火曜日　午後６時１１分

10Read Me FirstGetting StartedUseful InformationTroubleshootingAppendixDo Not Use With Any Other ProductThe battery pack is rechargeable and was intended for the specified product. If it is used with a product other than the one for which it was designed, electrolyte leak-age, generation of heat, ignition or rupture may result.Do Not Charge the Battery Using Methods Other ThanThose SpecifiedIf the battery is not charged using one of the specified methods, electrolyte leakage, generation of heat, ignition or rupture may result.Do Not Throw the Battery Pack into a Fire or Expose Itto Excessive HeatGeneration of heat, ignition or rupture may result.Avoid Extreme Heat (Near the Fire, in Direct Sunlight,for Example)Electrolyte leakage, generation of heat, ignition or rupture may result.Do Not Insert Sharp Objects into the Battery Pack,Expose It to Bumps or Shocks, Disassemble, or Modify ItElectrolyte leakage, generation of heat, ignition or rupture may result.• If this product is subjected to a strong impact, stop using it immediately.Do Not Short the Positive (+) and Negative (-) ContactsGeneration of heat, ignition or rupture may result. • Do not place the battery pack together with articles such as necklaces or hairpins when carrying or storing.Do Not Use This Product With a Battery Pack OtherThan the One SpecifiedUse only the specified battery pack (Î page 12) with your product. Use of battery packs other than those manufac-tured and supplied by Panasonic may present a safety hazard (generation of heat, ignition or rupture).When battery pack has deteriorated, replace it with anew oneContinued use of a damaged battery pack may result in heat generation, ignition or battery rupture.zDo not touch the terminals on the battery pack. The battery pack may no longer function properly if the contacts are dirty or damaged.zDo not expose the battery pack to water, or allow it to become wet.zIf the battery pack will not be used for a long period of time (a month or more), charge or discharge (use) the battery pack until the remaining battery level becomes 30% to 40% and store it in a cool, dry place.zThis computer prevents overcharging of the battery by recharging only when the remaining power is less than approx. 95% of capacity.zThe battery pack is not charged when the computer is first purchased. Be sure to charge it before using it for the first time. When the AC adaptor is connected to the computer, charging begins automatically.zShould the battery leak and the fluid get into your eyes, do not rub your eyes. Immediately flush your eyes with clear water and see a doctor for medical treatment as soon as possible.NOTEzThe battery pack may become warm during recharging or normal use. This is completely normal.zRecharging will not commence if internal temperature of the battery pack is outside of the allowable tempera-ture range (0 °C to 50 °C) (Î Reference Manual “Battery Power”). Once the allowable range require-ment is satisfied, charging begins automatically. Note that the recharging time varies based on the usage conditions. (Recharging takes longer than usual when the temperature is 10 °C or below.)zIf the temperature is low, the operating time is shortened. Only use the computer within the allowable temperature range.zThis computer has a high temperature mode function that prevents the degradation of the battery in high tempera-ture environments. (Î Reference Manual “Battery Power”) A level corresponding to a 100% charge for high temperature mode is approximately equivalent to an 80% charge level for normal temperature mode. zThe battery pack is a consumable item. If the amount of time the computer can be run by using a particular battery pack becomes dramatically shorter and repeated recharging does not restore its performance, the battery pack should be replaced with a new one.zWhen transporting a spare battery inside a package, briefcase, etc., it is recommended that it be placed in a plastic bag so that its contacts are protected.zAlways power off the computer when it is not in use. Leaving the computer on when the AC adaptor is not connected will exhaust the remaining battery capacity (Î Reference Manual “LAN”).Precautions (Battery Pack)CAUTION:Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions.58-E-1ATTENTION:Il y a risque d’explosion si la batterie est remplacée par une batterie de type incorrect.Mettre au rebut les batteries usagées conformément aux instructions. 58-F-1A lithium ion battery that is recycla-ble powers the product you have purchased.Please call 1-800-8-BATTERY for information on how to recycle this battery.L’appareil que vous vous êtes pro-curé est alimenté par une batterie au lithium-ion.Pour des renseignements sur le recyclage de la batterie, veuillez composer le 1-800-8-BATTERY.48-M-1DFQW5645ZAT_CF-53mk2_7_OI_M.book 10 ページ２０１２年５月８日　火曜日　午後６時１１分

11Getting StartedUseful InformationTroubleshootingAppendixDescription of PartsA : Wireless WAN antenna<Only for model with wireless WAN>Î Reference Manual “Wireless WAN”B : Bluetooth antenna<Only for model with Bluetooth>Î Reference Manual “Bluetooth”C : SpeakerÎ Reference Manual “Key Combinations”D : Smart Card slot<Only for model with Smart Card slot>Î Reference Manual “Smart Card”E : CD/DVD DriveÎ Reference Manual “CD/DVD Drive”F : Wireless LAN antenna<Only for model with wireless LAN>Î Reference Manual “Wireless LAN”G : Wireless LAN antenna<Only for model with wireless LAN and without GPS>Î Reference Manual “Wireless LAN”GPS antenna<Only for model with GPS>H : Camera<Only for model with Camera>Î Reference Manual “Camera”I : LCDÎ <Only for model with touchscreen> Reference Manual “Touchscreen”J : Power switchK : Function keyÎ Reference Manual “Key Combinations”L : Wireless LAN antenna<Only for model with wireless LAN and GPS>Î Reference Manual “Wireless LAN”M : Fingerprint Reader<Only for model with Fingerprint Reader>Î Reference Manual “Fingerprint Reader”N : KeyboardO : LED indicator : Caps lock : Numeric key (NumLk) : Scroll lock (ScrLk) : Drive status : SD Memory Card status(Blinking: During access or a password is requested)Î Reference Manual “SD Memory Card” : Wireless readyThis indicator lights when Wireless LAN, Blue-tooth, and/or Wireless WAN are connected and ready. It does not necessarily indicate the On/Off condition of the wireless connection.Î Reference Manual “Disabling/Enabling Wireless Communication” “Wireless LAN” “Blue-tooth” “Wireless WAN” : Battery statusÎ Reference Manual “Battery Power” : Power status(Off: Power off/Hibernation, Green: Power on, Blinking green: Sleep, Blinking green rapidly: Cannot power on or resume due to low tempera-ture.)P : Microphone jackA condenser microphone can be used. If other types of microphones are used, audio input may not be pos-sible, or malfunctions may occur as a result.Q : Headphone jackYou can connect headphones or amplified speakers.When they are connected, audio from the internal speakers is not heard.R : Stylus Holder<Only for model with touchscreen>S : RFID Reader<Only for model with RFID Reader>Î Reference Manual “RFID Reader”T : Carrying handleU : Touch padBCDEAGAICMLNOPQRSTRUKJFHDFQW5645ZAT_CF-53mk2_7_OI_M.book 11 ページ２０１２年５月８日　火曜日　午後６時１１分

12Description of PartsGetting StartedUseful InformationTroubleshootingAppendixA : Battery packSpecified Battery pack: CF-VZSU71UB : ExpressCard slot*1 / PC Card slot*2Î Reference Manual “PC Card / ExpressCard”*1 Only for model with ExpressCard slot*2 Only for model without ExpressCard slotC : PC Card slotÎ Reference Manual “PC Card / ExpressCard”D : SD Memory Card slotÎ Reference Manual “SD Memory Card”E : Wireless switchÎ Reference Manual “Disabling/Enabling Wireless Communication” “Wireless LAN” “Bluetooth” “Wireless WAN”F : USB 3.0 portÎ Reference Manual “USB Devices”G : DC-IN jackH : LAN portÎ Reference Manual “LAN”I : USB 2.0 port Î Reference Manual “USB Devices”J : HDMI PortÎ Reference Manual “External Display”K : VGA portÎ Reference Manual “External Display”L : Ventilation hole (Exhaust)M : Security lockA Kensington cable can be connected.For further information, read the manual that comes with the cable.N : SIM Card slot<Only for model with Wireless WAN>Î Reference Manual “Wireless WAN”O : 2nd LAN Port*3 / Modem Port*4 / IEEE 1394 Inter-face Connector*5 / Rugged USB 2.0 Port*6*3 Only for model with 2nd LANÎ Reference Manual “LAN”*4 Only for model with ModemÎ Reference Manual “Modem”*5 Only for model with IEEE 1394Î Reference Manual “IEEE 1394 Devices”*6 Only for model with Rugged USB 2.0 PortP : Serial portQ : Expansion bus connectorÎ Reference Manual “Port Replicator”R : RAM module slotÎ Reference Manual “RAM Module”S : Battery latchT : Hard disk driveÎ Reference Manual “Hard Disk Drive”NOTEzWhen you open the covers on the right side or the rear side, push down and pull the covers.zThis computer contains a magnet and magnetic prod-ucts at the locations circled in the illustration at right. Avoid leaving metallic object or mag-netic media in contact with these areas.AB C D EF GQRSTHI JK L OPMNRight sideRear side Bottom(Example: rear side)DFQW5645ZAT_CF-53mk2_7_OI_M.book 12 ページ２０１２年５月８日　火曜日　午後６時１１分

13Getting StartedUseful InformationTroubleshootingAppendixFirst-time OperationPreparationACheck and identify the supplied accessories.If you do not find the described accessories, contact Panasonic Technical Support (Îpages 32-36).BRead the LIMITED USE LICENSE AGREEMENT before breaking the seal on the computer’s packaging (Îpage 26).Inserting the Battery PackAReverse the computer, then press and hold the mark part (A).BSlide and remove the cover.CInsert the battery pack (B) until it securely fits the connector.DSlide the cover back.To remove the battery packIn step C above, slide and hold the latch (C), and pull the tab (D) of the battery pack.CAUTIONzMake sure the cover is securely attached. Otherwise the battery pack may fall when you carry the computer.NOTEzNote that the computer consumes electricity even when the computer power is off. If the battery pack is fully charged, the battery will fully discharge in the fol-lowing period of time:• When power is off: Approx. 9 weeks• In sleep: Approx. 3.5 days• In hibernation: Approx. 9 dayszWhen the DC plug is not connected to the computer, disconnect the AC cord from your AC wall outlet. Power is consumed simply by having the AC adaptor plugged into an electrical outlet.Attaching the stylus to the computer• AC Adaptor . . . . . . . . . . . . .1Model No: CF-AA5713A• AC Cord . . . . . . . . . . . . . . . 1 • Battery Pack . . . . . . . . . . . . 1Model No: CF-VZSU71U• OPERATING INSTRUCTIONS (This book). . . . . . . . . . . . . . . . . . . . . . . . 1<Only for model with touchscreen>• Soft Cloth. . . . . . . . . . . . . .1 • Stylus . . . . . . . . . . . . . . . . 1 • Tether . . . . . . . . . . . . . . . . 1(Î Reference Manual “Touchscreen”)2134DCBA<Only for model with touchscreen> Use the tether to attach the stylus to the computer so you will not lose it.There are holes (A) to attach it.CAUTIONzDo not pull the tether with excessive force. The digitizer pen may hit the com-puter, person’s body or other objects when released.A1 2 3 4DFQW5645ZAT_CF-53mk2_7_OI_M.book 13 ページ２０１２年５月８日　火曜日　午後６時１１分

14First-time OperationGetting StartedUseful InformationTroubleshootingAppendixOpening the DisplaySetting up the computerzDo not touch the terminals of the battery pack and the computer. Doing so can make the terminals dirty or damaged, and may cause malfunction of the battery pack and the computer.zBe sure to attach the cover for use.The battery charging starts automatically.CAUTIONzDo not disconnect the AC adaptor and do not switch the wireless switch to on until the first-time operation procedure is completed.zWhen using the computer for the first time, do not connect any peripheral device except the battery pack and AC adaptor.zHandling the AC adaptorProblems such as sudden voltage drops may arise during periods of thunder and lightning. Since this could adversely affect your computer, an uninterruptible power source (UPS) is highly recommended unless running from the battery pack alone.AConfirm the wireless switch (Îpage 12) is OFF.BPress and hold the power switch (Îpage 11) until the power indicator (Îpage 11) lights.CAUTIONzDo not press the power switch repeatedly.zThe computer will be forcibly turned off if you press and hold the power switch for four seconds or longer.zOnce you turn off the computer, wait for ten seconds or more before you turn on the computer again.zDo not perform the following operation until the drive indicator turns off.• Connecting or disconnecting the AC adaptor• Pressing the power switch• Touching the keyboard, touch pad, touchscreen <only for model with touch-screen> or external mouse• Closing the display• Turn on/off the wireless switchzWhen the CPU temperature is high, the computer may not start up to prevent overheating of the CPU. Wait until the computer cools down, and then turn the power on again. If the computer does not power on even after cooling down, contact Panasonic Technical Support (Îpages 32-36).APush the top of the latch (A) to release it.BLift up the display to open.A121 Insert the battery pack. (Îpage 13)2 Connect your computer to a power outlet.3 Turn on the computer.DFQW5645ZAT_CF-53mk2_7_OI_M.book 14 ページ２０１２年５月８日　火曜日　午後６時１１分

15Getting StartedUseful InformationTroubleshootingAppendixAFollow the on-screen instructions.zThe computer restarts several times. Do not touch the keyboard or touch pad, and wait until the drive indicator has turned off.zAfter the computer is turned on, the screen remains black or unchanged for a while, but this is not a malfunction. Wait for a moment until the Windows setup screen appears.zDuring setup of Windows, use the touch pad and clicking to move the cursor and to click an item.zSetup of Windows will take approximately 20 minutes.Go to the next step, confirming each message on the display.z“Join a wireless network” screen may not appear.You can set the Wireless Network after the setup of Windows is complete.CAUTIONzWait until the drive indicator has turned off.zYou can change the user name, password, image and security setting after setup of Windows.zDo not use the following words and characters for user name: CON, PRN, AUX, CLOCK$, NUL, COM1 to COM9, LPT1 to LPT9, @, &, space. In particular, if you create a user name (account name) that includes the “@” mark, a password will be requested at the log-on screen, even if no password has been set. If you try to log on without entering a password, “The user name or password is incorrect.” may be displayed and you will not be able to log on to Windows (Îpage 23).zBefore performing the calibration, close Tablet PC Input Panel.NOTEzAt first, log on to Windows as an administrator and perform this calibration.zAlternatively, you can perform the calibration from Dashboard for Panasonic PC. (Î Reference Manual “Dashboard for Panasonic PC”) AClick (Start) - [Control Panel] - [Hardware and Sound] - [Tablet PC Setting].BClick [Calibrate].CUsing the stylus, touch each of the “+” target marks one by one, and then click [Yes].DClick [OK].NOTEzPerform the following calibration for each user.zAlternatively, you can perform the calibration from Dashboard for Panasonic PC. (Î Reference Manual “Dashboard for Panasonic PC”)AClick (Start) - [Control Panel] - [Hardware and Sound] - [Tablet PC Setting].BClick [Calibrate].CUsing the stylus, touch each of the “+” target marks one by one, and then click [Yes].DClick [OK].zPerform the calibration for the orientation to be used.NOTEzPC Information ViewerThis computer periodically records the management information of the hard disk, etc. The maximum data volume for each record is 1024 bytes. This information is only used for estimating the cause when the hard disk goes down by any possibility. They are never sent to outside via network nor used for any other purpose except for the purpose described the above.To disable the function, add the check mark for [Disable the automatic save function for management information history] in [Hard Disk Status] of PC Information Viewer, and click [OK]. (Î Reference Manual “Checking the Computer’s Usage Status”)4 Setup Windows.5 <Only for model with touchscreen>Perform the touchscreen calibration.DFQW5645ZAT_CF-53mk2_7_OI_M.book 15 ページ２０１２年５月８日　火曜日　午後６時１１分

16First-time OperationGetting StartedUseful InformationTroubleshootingAppendixWhen Starting Up/Shutting DownDo not do the following• Connecting or disconnecting the AC adaptor• Pressing the power switch• Touching the keyboard, touch pad, touchscreen <only for model with touchscreen> or external mouse• Closing the display• Turn on/off the wireless switchNOTEzTo conserve power, the following power saving methods are set at the time of purchase.• The screen automatically turns off after 10 minutes of inactivity.• The computer automatically enters sleep*1 after 20 minutes of inactivity.*1 Refer to Reference Manual “Sleep and Hibernation Functions” about resuming from sleep.To change the partition structureYou can shrink a part of an existing partition to create unallocated disk space, from which you can create a new partition. This computer has a single partition as default setting.AClick (Start) and right-click [Computer], then click [Manage].zA standard user needs to enter an administrator password.BClick [Disk Management].CRight-click the partition for Windows (“c” drive in the default setting), and click [Shrink Volume].zThe partition size depends on the computer specifications.DInput the size in [Enter the amount of space to shrink in MB] and click [Shrink].zYou cannot input a larger number than the displayed size.zTo select [Reinstall to the first 3 partitions.] in reinstalling Windows 7 (Îpage 20), 30000 MB or more is nec-essary for [Total size after shrink in MB].ERight-click [Unallocated] (the shrunk space in the step D) and click [New Simple Volume].FFollow the on-screen instructions to make the settings, and click [Finish].Wait until formatting is completed.NOTEzYou can create an additional partition using remaining unallocated space or newly creating unallocated space.zTo delete a partition, right-click the partition and click [Delete Volume] in the step C.DFQW5645ZAT_CF-53mk2_7_OI_M.book 16 ページ２０１２年５月８日　火曜日　午後６時１１分

17Getting StartedUseful InformationTroubleshootingAppendixOn-screen ManualYou can access the Reference Manual on the computer screen.Reference Manual The Reference Manual contains the practical information to help you fully enjoy the computer’s performance.To access the Reference Manual:Double-click on the desktop.zAlternatively click (Start) - [All Programs] - [Panasonic] - [On-Line Manuals] - [Reference Manual].Important Tips The Important Tips will provide you with the battery information so that you can use the battery pack in the optimum condition to obtain longer operation time.To access the Important Tips:Double-click on the desktop.zAlternatively click (Start) - [All Programs] - [Panasonic] - [On-Line Manuals] - [Important Tips].DFQW5645ZAT_CF-53mk2_7_OI_M.book 17 ページ２０１２年５月８日　火曜日　午後６時１１分

$18Getting StartedUseful InformationTroubleshootingAppendixHandling and MaintenancezPlace the computer on a flat stable surface not subject to shock, vibration, and danger of dropping. Do not place the computer upright or turn it over. If the computer is exposed to an extremely strong impact, it may become damaged.zTemperature: Operation : <Model without HDD heater> 0 °C to 50 °C {32 °F to 122 °F} (IEC60068-2-1, 2)*1<Model with HDD heater> -10 °C to 50 °C {14 °F to 122 °F} (IEC60068-2-1, 2)*1Storage : -20 °C to 60 °C {- 4 °F to 140 °F}Humidity: Operation : 30% to 80% RH (No condensation)Storage : 30% to 90% RH (No condensation)Even within the above temperature/humidity ranges, operation for a long time in extreme environments, smoking nearby, or operation in places where oil is used or where there is a lot of dust will result in the product deterioration and will shorten the product life.*1 Do not expose the skin to this product when using the product in a hot or cold environment. (Î page 9)If the computer is wet in temperatures of 0 °C {32 °F} or below, freeze damage may occur. Make sure to dry off the computer in such temperatures.zDo not place the computer in the following areas, otherwise the computer may be damaged.• Near electronic equipment. Image distortion or noise may occur.• In extremely high or low temperature.zAs the computer can become hot during operation, keep it away from items that are sensitive to heat.This computer is designed to minimize shock to parts such as the LCD and the hard disk drive and equipped with a drip-proof keyboard, but no warranty is provided against any trouble caused by shock. Be extremely careful when handling the computer.zWhen carrying the computer:• Turn off the computer.• Remove all external devices, cables, PC Cards and other protruding objects.• Remove a disc in the CD/DVD drive.• Do not drop or hit the computer against solid objects.• Do not leave the display open.• Do not grip the display part.zDo not put anything (e.g., a piece of paper) between the display and keyboard.zWhen you board an airplane, take the computer with you and never put it in your checked luggage. When using the computer on airplane, follow the airline’s instructions.zWhen carrying a spare battery, put it in a plastic bag to protect its terminals.zThe touch pad is designed to be used by finger tip. Do not place any object on its surface and do not press down strongly with sharp-pointed or hard objects that may leave marks (e.g., nails, pencils and ball point pens).zAvoid any harmful substances such as oil from getting into the touch pad. The cursor may not work correctly.zBe careful not to get injured by dropping or getting hit when carrying the computer.<Only for model with touchscreen>zUse only the included stylus to touch the touchscreen. Do not place any object on its surface and do not press down strongly with sharp-pointed or hard objects that may leave marks (e.g., nails, pencils and ball point pens).zDo not use the touchscreen when dust or dirt (e.g., oil) is on the screen. Otherwise foreign particles on the screen/stylus can scratch the screen surface or obstruct the stylus operation.zUse the stylus only for touching the screen. Using it for any other purpose may damage the stylus and result in scratches on the screen.When using peripheral devicesFollow these instructions and the Reference Manual to avoid any damage to the devices. Carefully read the instruction manuals of the peripheral devices.zUse the peripheral devices conforming to the computer’s specifications.zConnect to the connectors in the correct direction.zIf it is hard to insert, do not try forcibly but check the connector’s shape, direction, alignment of pins, etc.zIf screws are included, fasten them securely.zRemove the cables when you carry the computer. Do not pull the cables forcibly.Preventing your computer from unauthorized use via wireless LAN/Bluetooth/Wireless WAN<Only for model with wireless LAN/Bluetooth/Wireless WAN>zBefore using wireless LAN/Bluetooth/Wireless WAN, make the appropriate security settings such as data encryption.Operation EnvironmentHandling CautionsDFQW5645ZAT_CF-53mk2_7_OI_M.book 18 ページ２０１２年５月８日　火曜日　午後６時１１分$

19Getting StartedUseful InformationTroubleshootingAppendixBattery RecalibrationzThe battery recalibration may take a long time due to the large battery capacity. This is not a malfunction.• Full charge: Approximately 2 hours• Complete discharge: Approximately 2 hoursIf drops of water or other stains get on the surface of the LCD panel, wipe them off immediately. Failure to do so may result in staining.To clean the LCD panel<Only for model with touchscreen>Use the soft cloth included with the computer. (For further information, refer to “Suggestions About Cleaning the LCD Surface” Î Reference Manual “Touchscreen”.)<Only for model without touchscreen>Wipe with a soft dry cloth such as gauze.To clean areas other than the LCD panelWipe with a soft dry cloth such as gauze. When using detergent, dip a soft cloth in water-diluted detergent and wring it thoroughly. CAUTIONzDo not use benzene, thinner, or rubbing alcohol since it may adversely affect the surface causing discoloration, etc. Do not use commercially-available household cleaners and cosmetics, as they may contain components harmful to the surface.zDo not apply water or detergent directly to the computer, since liquid may enter inside of the computer and cause malfunction or damage.MaintenanceDFQW5645ZAT_CF-53mk2_7_OI_M.book 19 ページ２０１２年５月８日　火曜日　午後６時１１分

20Getting StartedUseful InformationTroubleshootingAppendixReinstalling SoftwareCAUTIONzDo not delete the recovery partition on the hard disk.The disk space in the partition is not available to store data.Hard Disk RecoveryPreparationzRemove all peripherals.zConnect the AC adaptor and do not remove it until reinstallation is complete.1 Turn on the computer, and press F2 or Del while [Panasonic] boot screen is displayed.The Setup Utility starts up.• If the [Panasonic] boot screen is not displayed, turn on the computer while holding down F2 or Del.• If the password is requested, enter the Supervisor Password.2 Write down all of the contents of the Setup Utility and press F9.At the confirmation message, select [Yes] and press Enter.3 Press F10.At the confirmation message, select [Yes] and press Enter.Computer will restart.4 Press F2 or Del while [Panasonic] boot screen is displayed.The Setup Utility starts up.• If the password is requested, enter the Supervisor Password.5 Select the [Exit] menu, then select [Recovery Partition] and press Enter.6 Click [Reinstall Windows] and click [Next].The License Agreement screen appears.7 Click [Yes, I agree to the provisions above and wish to continue!] and click [Next].8 Select the settings and click [Next].• [Reinstall Windows to the whole Hard Disk to factory default.]Select this option when you want to reinstall Windows to the factory default. After reinstallation, you can create a new partition. For how to create a new partition, refer to “To change the partition structure” (Î page 16)• [Reinstall to the System and OS partitions.]*1Select this option when the hard disk has already been divided into several partitions. For how to create a new partition, refer to “To change the partition structure” (Îpage 16).You can keep the partition structure.*1This does not appear if Windows cannot be reinstalled to the partition containing boot files and the area usable by Windows.9 At the confirmation massage, click [YES].10 Select OS (32bit or 64bit) and click [OK].11 At the confirmation message, click [OK].Reinstallation starts according to the instructions on the screen.• Do not interrupt reinstallation, for example by turning off the computer. Otherwise reinstallation may become unavailable as Windows may not start up or the data may be corrupted.12 When “Ending process.” is displayed, click [OK] to turn off the computer.13 Turn on the computer.• If the password is requested, enter the Supervisor Password.14 Perform the “First-time Operation” (Îpage 15).15 Start the Setup Utility and change the settings as necessary.16 Perform Windows Update.Reinstalling software will return the computer to the default condition. When you reinstall the software, the hard disk data will be erased.Back up important data to other media or an external hard disk before reinstallation.Area usable by WindowsHard disk HDD Recovery partitionRecovery partitionDFQW5645ZAT_CF-53mk2_7_OI_M.book 20 ページ２０１２年５月８日　火曜日　午後６時１１分

21Getting StartedUseful InformationTroubleshootingAppendixUsing Recovery DiscUse the Recovery Disc for reinstallation in the following conditions.• You have forgotten the administrator password.• Reinstallation is not complete. The recovery partition may be broken.NOTE• To change OS from 32-bit to 64-bit, or vice versa, reinstall OS using the recovery partition in the hard disk.PreparationzPrepare the Recovery Disc (Î Reference Manual “Recovery Disc Creation Utility”)zRemove all peripherals.zConnect the AC adaptor and do not remove it until reinstallation is complete.1 Turn on the computer, and press F2 or Del while [Panasonic] boot screen is displayed.The Setup Utility starts up.• If the [Panasonic] boot screen is not displayed, turn on the computer while holding down F2 or Del.• If the password is requested, enter the Supervisor Password.2 Write down all of the contents of the Setup Utility and press F9.At the confirmation message, select [Yes] and press Enter.3 Press F10.At the confirmation message, select [Yes] and press Enter.Computer will restart.4 Press F2 or Del while [Panasonic] boot screen is displayed.The Setup Utility starts up.• If the password is requested, enter the Supervisor Password.5 Set the Recovery Disc into the CD/DVD drive.6 Select the [Exit] menu, then select [Slimtype DVD...] in [Boot Override].7 Press Enter.The computer will restart.8 Click [Reinstall Windows] and click [Next].The License Agreement screen appears.9 Click [Yes, I agree to the provisions above and wish to continue!] and click [Next].10 Select the settings and click [Next].• [Reinstall Windows to the whole Hard Disk to factory default.Select this option when you want to reinstall Windows to the factory default. After reinstallation, you can create a new partition. For how to create a new partition, refer to “To change the partition structure” (Î page 16)• [Reinstall to the first 3 partitions.]*2Select this option when the hard disk has already been divided into several partitions. For how to create a new partition, refer to “To change the partition structure” (Î page 16).You can keep the partition structure.*2 This does not appear if Windows cannot be reinstalled to the partition containing boot files and the area usable by Windows.11 At the confirmation message, click [YES].Reinstallation starts. (It will take approximately 70 minutes.)According to the screen, replace the Recovery Disc.• Do not interrupt reinstallation, for example by turning off the computer. Otherwise reinstallation may become unavailable as Windows may not start up or the data may be corrupted.12 When “Ending process.” is displayed, remove the Recovery Disc, and then click [OK] to turn off the computer.13 Turn on the computer.• If the password is requested, enter the Supervisor Password.14 Perform the “First-time Operation” (Î page 15).15 Start the Setup Utility and change the settings as necessary.16 Perform Windows Update.DFQW5645ZAT_CF-53mk2_7_OI_M.book 21 ページ２０１２年５月８日　火曜日　午後６時１１分

$22Getting StartedUseful InformationTroubleshootingAppendixTroubleshooting (Basic)Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the “Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact Panasonic Technical Support (Îpages 32-36). You can also check the computer’s status in the PC Information Viewer (Î Reference Manual “Checking the Computer’s Usage Status”).Starting UpCannot start up.The power indicator or bat-tery indicator is not lit.zConnect the AC adaptor.zInsert a fully charged battery.zRemove the battery pack and the AC adaptor, then connect them again. zEven if the AC adaptor and battery pack are correctly connected, if the battery indi-cator is not lit, the AC adaptor protection function may be operating. Disconnect the AC cord, wait three minutes or more, and reconnect the AC cord.zIf a device is connected to the USB port, disconnect the device, or set [USB Port] or [Legacy USB Support] to [Disabled] in the [Advanced] menu of the Setup Utility.zIf a device is connected to the ExpressCard slot, disconnect the device, or set [Express-Card Slot] to [Disabled] in the [Advanced] menu of the Setup Utility.The power is turned on but “Warming up the system (up to 30 minutes)” appears.zThe computer is warming up before start up. Wait for the computer to start up (takes up to 30 minutes). If, “Cannot warm up the system” is displayed, the computer failed to warm up and does not start. In this case, turn off the computer, leave it in an envi-ronment of 5 °C {41 °F} or higher temperature for about an hour, and then turn on the power once more.Cannot turn on the computer.The computer does not resume from sleep.(The power indicator blinks quickly in green.)zLeave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, then turn on the power once more.After adding or changing the RAM module, the power is turned on but nothing is displayed on the screen.zTurn off the computer and remove the RAM module, then confirm whether the RAM module has conformed to specification. When the RAM module has conformed to specification, install it again.The computer does not enter sleep mode while the screen saver is running (The screen stays black).zPress and hold the power switch for four seconds or longer to shut down the com-puter forcibly. (Data not saved will be lost.) Then disable the screen saver.It takes time for the power indicator to light up.zIf the power switch is pressed immediately after the battery pack has been mounted on the computer, and while the AC adaptor is not connected, it may take about five seconds before the power indicator lights up and the computer turns on. This is because the computer is checking the remaining battery charge; it is not a malfunc-tion.You have forgotten the password.zSupervisor Password or User Password: Contact Panasonic Technical Support (Îpages 32-36).zAdministrator password: • If you have another account with Administrator authority, log-on with it, then delete the password for the problem account.• If you have a password reset disk, click [Reset password] displayed after the password input error, then follow the on-screen instructions and set a new pass-word.If you cannot do either of the above, you will need to reinstall (Îpage 20) and setup Windows.“Remove disks or other media. Press any key to restart” or a similar mes-sage appears.zA floppy disk in the drive or USB memory is connected, and it does not contain system startup information. Remove the floppy disk and USB memory, then press any key.zIf a device is connected to the USB port, disconnect the device, or set [USB Port] or [Legacy USB Support] to [Disabled] in the [Advanced] menu of the Setup Utility.zIf a device is connected to the ExpressCard slot, disconnect the device, or set [Express-Card Slot] to [Disabled] in the [Advanced] menu of the Setup Utility.z<Only for model with ExpressCard slot>If the problem persists after removing the disk, it may be a hard disk failure. Contact Panasonic Technical Support (Îpages 32-36).DFQW5645ZAT_CF-53mk2_7_OI_M.book 22 ページ２０１２年５月８日　火曜日　午後６時１１分$

23Getting StartedUseful InformationTroubleshootingAppendixWindows startup and opera-tion is slow.zPress F9 in the Setup Utility (Î Reference Manual “Setup Utility”) to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again. (Note that the processing speed depends on the application software, so this procedure may not make Windows faster.)zIf you installed a resident software after purchase, turn off the residence.The date and time are incor-rect.zMake the correct settings. Click (Start) - [Control Panel] - [Clock, Language, and Region] - [Date and Time].zIf the problem persists, the internal clock battery may need to be replaced. Contact Panasonic Technical Support (Îpages 32-36).zWhen the computer is connected to LAN, check the date and time of the server.zThe 2100 A.D. or later year will not be correctly recognized on this computer.[Executing Battery Recali-bration] screen appears.zThe Battery Recalibration was canceled before Windows was shut down last time. To start up Windows, turn off the computer by the power switch, and then turn on.[Enter Password] does not appear when resuming from sleep / hibernation.zSelect [Enabled] in [Password On Resume] in the [Security] menu of the Setup Utility (Î Reference Manual “Setup Utility”).zThe Windows password can be used instead of the password set in the Setup Utility.AClick (Start) - [Control Panel] - [User Accounts and Family Safety] - [Add or remove user accounts] and select the account, and set the password.BClick (Start) - [Control Panel] - [System and Security] - [Power Options] - [Require a password on wakeup] and add a check mark for [Require a password].Cannot resume. zAn error may occur when the computer automatically enters the sleep or hibernation mode while the screen saver is active. In this case, turn off the screen saver or change the pattern of the screen saver.Other startup problems. zPress F9 in the Setup Utility (Î Reference Manual “Setup Utility”) to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again.zRemove all peripheral devices.zCheck to see if there was a disk error.ARemove all peripheral devices including an external display.BClick (Start) - [Computer] and right-click [Local Disk (C:)], and click [Properties].CClick [Tools] - [Check Now...].• A standard user needs to enter an administrator password.DSelect the option in [Check disk options] and click [Start].EClick [Schedule disk check] and restart the computer.Entering PasswordEven after entering the password, password input screen is displayed again.zThe computer may be in ten-key mode.If the NumLk indicator lights, press NumLk to disable the ten-key mode, and then input.zThe computer may be in Caps Lock mode.If the Caps Lock indicator lights, press Caps Lock to disable the Caps Lock mode, and then input.Cannot log on to Windows. (“The user name or pass-word is incorrect” is dis-played.)zThe user name (account name) includes an “@” mark.If another user account exists:Log on to Windows using another user account, and delete the account that includes “@”. Then create a new account.If no other account exists:You need to reinstall Windows (Îpage 20).Shutting downWindows does not shut down.zRemove the USB device and the ExpressCard.zWait one or two minutes. It is not a malfunction.Starting UpDFQW5645ZAT_CF-53mk2_7_OI_M.book 23 ページ２０１２年５月８日　火曜日　午後６時１１分

24Troubleshooting (Basic)Getting StartedUseful InformationTroubleshootingAppendixDisplayNo display. zThe external display is selected. Press Fn + F3 or + P to switch the display. Wait until the display has been switched completely before pressing Fn + F3 or +P again.zWhen using an external display,• Check the cable connection.• Turn on the display.• Check the settings of external display.zThe display is turned off by the power-saving function. To resume, do not press the direct selection keys, but press any other key like Ctrl.zThe computer entered sleep or hibernation by the power-saving function. To resume, press the power switch.The screen is dark. zThe screen is darker when the AC adaptor is not connected. Press Fn + F2 and adjust the brightness. As you increase the brightness, battery consumption increases.You can separately set the brightness for when the AC adaptor is connected and when not connected.zPress Fn + F8 to turn off the concealed mode.The screen is disordered. zChanging the number of display colors and resolution may affect the screen. Restart the computer.zConnecting/disconnecting an external display may affect the screen. Restart the computer.zResuming from sleep or hibernation may affect the screen of the external display. Restart the computer.During Simultaneous dis-play, one of the screens becomes disordered.zWhen using the Extended Desktop, use the same display colors for the external dis-play as those used by the LCD.If you continue to experience problems, try changing the display. Right-click on the desktop, and click [Graphics Properties...] - [Display].zSimultaneous display cannot be used until Windows startup is complete (during Setup Utility, etc.).The external display does not work normally.zIf the external display does not support the power saving function, it may not work nor-mally when the computer enters the power saving mode. Turn off the external display.Touch Pad / Touchscreen (only for model with touchscreen)The cursor does not work. zWhen using the external mouse, connect it correctly.zRestart the computer using the keyboard. Press and press Î twice, and press Ï to select [Restart] and press Enter.zIf the computer does not respond to keyboard commands, read “No response” (Îpage 25).Cannot input using the touch pad.zSet [Touch Pad] to [Enabled] in the [Main] menu of the Setup Utility.zThe drivers for some mice may disable the touch pad. Check your mouse’s operat-ing instructions.<Only for model with touchscreen>Cannot input using the touchscreen.zSet [Touchscreen Mode] to [Auto] or [Tablet] in the [Main] menu of the Setup Utility.Cannot point the correct position using the included stylus.zPerform the touchscreen calibration (Îpage 15).DFQW5645ZAT_CF-53mk2_7_OI_M.book 24 ページ２０１２年５月８日　火曜日　午後６時１１分

$25Getting StartedUseful InformationTroubleshootingAppendixOn-screen DocumentThe document of PDF for-mat is not displayed.zInstall Adobe Reader.ALog on to Windows as an administrator.BClick (Start) and input “c:\util\reader\AdbeRdr1001_en_US.exe” in [Search programs and files] then press Enter.CUpdate Adobe Reader to its latest version.If your computer is connected to the internet, start up Adobe Reader and click [Help] - [Check for Updates...].CD/DVD DriveThe tray does not come out although inserting a pointed object to the emergency hole.zA pin of 1.3 mm in diameter is recommended to remove a disc using the emergency hole (A). When the diameter of the pin is smaller than this, insert the pin slightly downward.OthersNo response. zPress Ctrl+Shift+Esc to open Task Manager and close the software application that is not responding.zAn input screen (e.g., password input screen at startup) may be hidden behind another window. Press Alt+Tab to check.zPress the power switch for four seconds or longer to shut down the computer, and then press the power switch to turn it on. If the application program does not work normally, uninstall and reinstall the program. To uninstall, click (Start) - [Control Panel] - [Uninstall a program].ADFQW5645ZAT_CF-53mk2_7_OI_M.book 25 ページ２０１２年５月８日　火曜日　午後６時１１分$

26Getting StartedUseful InformationTroubleshootingAppendixLIMITED USE LICENSE AGREEMENTTHE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC PRODUCT (“PRODUCT”) ARE LICENSED ONLY TO THE END-USER (“YOU”), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY DEEMED TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE.Panasonic Corporation has developed or otherwise obtained the Programs and hereby licenses their use to you. You assume sole responsibility for the selection of the Product (including the associated Programs) to achieve your intended results, and for the installation, use and results obtained therefrom.LICENSEA. Panasonic Corporation hereby grants you a personal, non-transferable and non-exclusive right and license to use the Programs in accordance with the terms and conditions stated in this Agreement. You acknowledge that you are receiving only a LIMITED LICENSE TO USE the Programs and related documentation and that you shall obtain no title, ownership nor any other rights in or to the Programs and related documentation nor in or to the algorithms, con-cepts, designs and ideas represented by or incorporated in the Programs and related documentation, all of which title, ownership and rights shall remain with Panasonic Corporation or its suppliers.B. You may use the Programs only on the single Product which was accompanied by the Programs.C. You and your employees and agents are required to protect the confidentiality of the Programs. You may not distrib-ute or otherwise make the Programs or related documentation available to any third party, by time-sharing or other-wise, without the prior written consent of Panasonic Corporation.D. You may not copy or reproduce, or permit to be copied or reproduced, the Programs or related documentation for any purpose, except that you may make one (1) copy of the Programs for backup purposes only in support of your use of the Programs on the single Product which was accompanied by the Programs. You shall not modify, or attempt to modify, the Programs.E. You may transfer the Programs and license them to another party only in connection with your transfer of the single Product which was accompanied by the Programs to such other party. At the time of such a transfer, you must also transfer all copies, whether in printed or machine readable form, of every Program, and the related documentation, to the same party or destroy any such copies not so transferred.F. You may not remove any copyright, trademark or other notice or product identification from the Programs and you must reproduce and include any such notice or product identification on any copy of any Program.YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANICALLY OR ELECTRONICALLY TRACE THE PROGRAMS, OR ANY COPY THEREOF, IN WHOLE OR IN PART.YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PROGRAMS OR ANY COPY THEREOF, IN WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE.IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO ANOTHER PARTY, EXCEPT AS PER-MITTED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY TERMINATED.TERMThis license is effective only for so long as you own or lease the Product, unless earlier terminated. You may terminate this license at any time by destroying, at your expense, the Programs and related documentation together with all cop-ies thereof in any form. This license will also terminate effective immediately upon occurrence of the conditions thereof set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein. Upon any such termination, you agree to destroy, at your expense, the Programs and related documentation together with all cop-ies thereof in any form.YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT IT IS THE COMPLETE AND EXCLUSIVE STATE-MENT OF THE AGREEMENT BETWEEN US, WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT, ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MAT-TER OF THIS AGREEMENT.GOVERNMENT RESTRICTED RIGHTS.The Software is provided with “RESTRICTED RIGHTS.” Use duplication or disclosure by the government is sub-ject to restrictions as set forth in FAR52.227-14 and DFAR252. 227-7013 et seq. or their successors.Use of the Software by the government constitutes acknowledgement of Intel’s proprietary rights therein.Contractor or Manufacturer is Intel Corporation, 2200 Mission College Blvd., Santa Clara, CA 95052.DFQW5645ZAT_CF-53mk2_7_OI_M.book 26 ページ２０１２年５月８日　火曜日　午後６時１１分

27Getting StartedUseful InformationTroubleshootingAppendixContrat de licence d’usage limitéLe(s) logiciel(s) (les “Logiciels”) fournis avec ce produit Panasonic (le “Produit”) sont exclusivement concédés en licence à l’utilisateur ultime (“vous”), et ils ne peuvent être utilisés que conformément aux clauses contractuelles cidessous. En utilisant les logiciels, vous vous engagez de manière définitive à respecter les termes, clauses et conditions des présentes.Panasonic Corporation a mis au point ou obtenu les Logiciels et vous en concède l’utilisation par les présentes. Vous assumez l’entière responsabilité du choix de ce Produit (y compris des Logiciels associés) pour obtenir les résultats escomptés, ainsi que de l’installation, de l’utilisation et des résultats obtenus.LicenceA. Panasonic Corporation vous octroie par les présentes le droit et la licence personnels, non cessibles et non exclusifs d’utiliser les Logiciels conformément aux termes, clauses et conditions de ce contrat. Vous reconnaissez ne recevoir qu’un droit limité d’utiliser les Logiciels et la documentation les accompagnant et vous vous engagez à n’obtenir aucun droit de titre, propriété ni aucun autre droit vis-à-vis des Logiciels et de la documentation les accompagnant ni vis-à-vis des algorithmes, concepts, dessins, configurations et idées représentés par ou incorporés dans les Logiciels et la documentation les accompagnant, dont les titres, la propriété et les droits resteront tous à Panasonic Corporation ou à leurs propriétaires.B. Vous ne pouvez utiliser les Logiciels que sur le Produit unique qui est accompagné par les Logiciels.C. Vous et vos employés ou agents êtes requis de protéger la confidentialité des Logiciels. Vous ne pouvez ni distribuer ni mettre les Logiciels et la documentation les accompagnant à la disposition d’un tiers, par partage de temps ou de quelque autre manière que ce soit, sans l’autorisation écrite préalable de Panasonic Corporation.D. Vous ne pouvez ni copier ni reproduire ni permettre la copie ni la reproduction des Logiciels ni de la documentation les accompagnant pour quelque fin que ce soit, à l’exception d’une (1) copie des Logiciels à des fins de sauvegarde uniquement pour soutenir votre utilisation des Logiciels sur le Produit unique qui est accompagné par les Logiciels. Vous ne pouvez ni modifier ni tenter de modifier les Logiciels.E. Vous ne pouvez céder les Logiciels et en octroyer la licence à une autre partie qu’en rapport avec votre cession du Produit unique qui est accompagné par les Logiciels à cette autre partie. Au moment de cette cession, vous devez céder également toutes les copies, que ce soit sous forme imprimée ou lisible par la machine, de tous les Logiciels ainsi que de la documentation les accompagnant, à la même partie ou détruire les copies non cédées.F. Vous ne pouvez retirer aucune marque de droits d’auteur, marque de commerce ou autre ni aucune identification de produit des Logiciels et vous devez reproduire et inclure toutes ces notices ou identifications de produit sur toutes les copies des Logiciels.Vous ne pouvez assembler en sens inverse, compiler en sens inverse ni retracer les Logiciels ni aucune de leurs copies, de façon électronique ou mécanique, en tout ou en partie.Vous ne pouvez utiliser, copier, modifier, altérer ni céder les Logiciels ni aucune de leurs copies, en tout ou en partie, à l’exception de ce qui est expressément stipulé dans ce contrat.Si vous cédez la possession de toute copie ou de tout Logiciel à une autre partie, à l’exception de ce qui est autorisé au paragraphe E ci-dessus, votre licence est automatiquement résiliée.Termes, clauses et conditionsCette licence n’est effective que pour la durée de possession ou de crédit-bail du Produit, à moins d’une résiliation antérieure. Vous pouvez résilier cette licence à tout moment en détruisant, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme que ce soit. Cette licence sera également résiliée, avec application immédiate, si les conditions de résiliation définies ailleurs dans ce contrat se sont réalisées ou si vous ne respectez pas les termes, clauses et conditions qui y sont contenues. Au moment de la résiliation, vous acceptez de détruire, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme que ce soit.Vous reconnaissez avoir lu ce contrat, en avoir compris toute la substance et avoir accepté de respecter ses termes, clauses et conditions. Vous reconnaissez en outre qu’ils sont la description complète et exclusive du contrat conclu entre nous, contrat qui remplace et annule toute proposition ou contrat précédent, écrit ou oral, et toute autre communication entre nous, relativement à l’objet du présent contrat.DFQW5645ZAT_CF-53mk2_7_OI_M.book 27 ページ２０１２年５月８日　火曜日　午後６時１１分

28Getting StartedUseful InformationTroubleshootingAppendixSpecificationsThis page provides the specifications for the basic model. The model number is different according to the unit configu-ration.zTo check the model number:Check the bottom of the computer or the box the computer came in at the time of purchase.zTo check CPU speed, memory size and the hard disk drive (HDD) size:Run the Setup Utility (Î Reference Manual “Setup Utility”) and select [Information] menu.[Processor Speed]: CPU speed, [Memory Size]: Memory size, [Hard Disk]: Hard disk drive sizeMain SpecificationsModel No. CF-53JALZYDM CF-53JSLZYDMCPU/Secondary cache memory i5-3320M Processor (3 MB*1 cache, up to 3.3 GHz) with Intel® Turbo Boost TechnologyChip Set Intel® 7 Series Express Chipsets QM77Video controller Built-in Chip SetMain Memory*2 4 GB*1, DDR3L SDRAM (16 GB*1 Max.)Video Memory UMA (<32-bit> 1419 MB*1 Max., <64-bit> 1696 MB*1 Max.)*3Hard Disk Drive 500 GB*4 (Serial ATA)Approx. 10 GB*4 is used as a partition with recovery tools. (Users cannot use this partition.)CD/DVD drive DVD MULTI Drive built-in, Buffer underrun error prevention function: Supported, Zero Power ODD: SupportedContinuous Data Transfer Speed*5*6Reading*7zDVD-RAM*8: 5X (Max.) zDVD-R*9: 8X (Max.) zDVD-R DL: 8X (Max.) zDVD-RW: 8X (Max.) zDVD-ROM: 8X (Max.) z+R DL: 8X (Max.) z+RW: 8X (Max.) zHigh Speed +RW: 8X (Max.) zCD-ROM: 24X (Max.) zCD-R: 24X (Max.) zCD-RW: 24X (Max.) zHigh-Speed CD-RW: 24X (Max.) zUltra-Speed CD-RW: 24X (Max.)Writing*10zDVD-RAM*8: 5X (Max.) zDVD-R*9: 8X (Max.) zDVD-R DL: 6X (Max.) zDVD-RW: 6X (Max.) z+R DL: 6X (Max.) z+RW: 4X (Max.) zHigh Speed +RW: 8X (Max.) zCD-R: 24X (Max.) zCD-RW: 4X zHigh-Speed CD-RW: 10X zUltra-Speed CD-RW: 24X (Max.) Supported Discs/FormatReadingzDVD-ROM (Single Layer, Dual Layer) zDVD-Video zDVD-R*9 (1.4 GB, 3.95 GB, 4.7 GB)*4 zDVD-R DL (8.5 GB)*4 zDVD-RW (Ver.1.1/1.2 1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB)*4 zDVD-RAM*8 (1.4 GB, 2.6 GB, 2.8 GB, 4.7 GB, 5.2 GB, 9.4 GB)*4 z+R (4.7 GB)*4 z+R DL (8.5 GB)*4 z+RW (4.7 GB)*4 zHigh Speed +RW (4.7 GB)*4 zCD-Audio zCD-ROM (XA compatible) zCD-R zPhoto CD (multiple session compatible) zVideo CD zCD-EXTRA zCD-RW zCD-TEXTzHigh-Speed CD-RW zUltra-Speed CD-RWWriting zDVD-RAM*8 (1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB)*4 zDVD-R*9 (1.4 GB, 4.7 GB for General)*4 zDVD-R DL (8.5 GB)*4 zDVD-RW (Ver.1.1/1.2 1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB)*4 z+R (4.7 GB)*4 z+R DL (8.5 GB)*4 z+RW (4.7 GB)*4 zHigh Speed +RW (4.7 GB)*4 zCD-R zCD-RW zHigh-Speed CD-RW zUltra-Speed CD-RW Display Method 14 type (TFT) (1366 × 768 dots) 14 type with Touchscreen (TFT) (1366 × 768 dots)Internal LCD 65,536 / 16,777,216 colors (800 × 600 dots / 1024 × 768 dots / 1280 × 600 dots / 1280 × 720 dots / 1280 × 768 dots / 1360 × 768 dots / 1366 × 768 dots)*11External Display*12 65,536 / 16,777,216 colors (800 × 600 dots / 1024 × 768 dots / 1280 × 768 dots / 1600 × 1200 dots / 1920 × 1080 dots / 1920 × 1200 dots)Wireless LAN*13 Intel® Centrino® Advanced-N 6205 (Îpage 30)Bluetooth*14 Îpage 30Wireless WAN*15 Sierra™ Wireless High-speed moduleGPS*16 Chip: SiRF starIIIAccuracy: 10 m (2DRMS, 5 m (2DRMS, SBAS)Protocol message: GGA, GSA, GSV, RMC, VTGLAN IEEE 802.3 10Base-T / IEEE 802.3u 100BASE-TX / IEEE 802.3ab 1000BASE-T(2nd LAN*17: IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX)Modem*18 Data: 56 kbps (V.92) FAX: 14.4 kbpsSound WAVE and MIDI playback, Intel® High Definition Audio subsystem supportDFQW5645ZAT_CF-53mk2_7_OI_M.book 28 ページ２０１２年５月８日　火曜日　午後６時１１分

$29Getting StartedUseful InformationTroubleshootingAppendixSecurity Chip TPM (TCG V1.2 compliant)*19Card Slots PC Card Slotx 1*20 or 2*21, Type I or Type II, Allowable current 3.3 V: 400 mA, 5 V: 400 mAExpressCard Slot*22 x 1, ExpressCard/34 or ExpressCard/54SD Memory Card Slot*23 x 1 Contact Smart Card Slot*24 x 1RAM Module Slot x 2, DDR3L SDRAM, 204-pin, 1.35 V, SO-DIMM, PC3L-10600 CompliantInterface USB Ports × 4 (USB 2.0 × 2 + USB 3.0 × 2)*25/ Serial Port (Dsub 9-pin male) / Modem Port (RJ-11)*18/ LAN Port (RJ-45) × 1*26 or 2*17 / VGA Port (Mini Dsub 15-pin female) / HDMI Port (Type A)*27 / IEEE1394a Interface Connector (4-pin)*28 / Microphone Jack (Miniature jack, 3.5 DIA) / Headphone Jack (Miniature jack, 3.5 DIA, Impedance 32 Ω, Output Power 4 mW × 2, Ste-reo) / Expansion Bus Connector (Dedicated 100-pin female/ Rugged USB 2.0 Port*29)Keyboard / Pointing Device 87 keys / Touch Pad 87 keys / Touch Pad, TouchscreenFingerprint Reader*30 Array Size : 192 x 4 pixels, Image Size : 192 x 512 pixels, Image Resolution : 508 DPIRFID Reader*31 RF frequency: 13.56 MHz, compatible with ISO14443 TYPE-A, ISO14443 TYPE-B, ISO15693Camera*32 1280 × 1024 dots, 30 fpsPower Supply AC adaptor or Battery packAC Adaptor*33 Input: 100 V - 240 V AC, 50 Hz/60 Hz, Output: 15.6 V DC, 7.05 ABattery Pack Li-ion 10.8 V, Typical 6750 mAh / Minimum 6300 mAhOperating Time*34 Approx. 11 hoursCharging Time*35 Approx. 2 hoursPower Consumption*36Approx. 30 W*37/ Approx. 100 W (maximum when recharging in the ON state)Physical Dimensions (W × D × H)(including the carrying handle)340 mm × 281 mm × 46 - 55 mm {13.4" × 11.1" × 1.9" - 2.2"}Weight (including the carrying handle) Approx. 2.65 kg {Approx. 5.84 lb.}Approx. 2.95 kg {Approx. 6.50 lb.}Envi-ronmentOper-atingTemperature <Model without HDD heater> 0 °C to 50 °C {32 °F to 122 °F } (IEC60068-2-1, 2)*38<Model with HDD heater> -10 °C to 50 °C {14 °F to 122 °F} (IEC60068-2-1, 2)*38Humidity 30% to 80% RH (No condensation)Stor-ageTemperature -20 °C to 60 °C {-4 °F to 140 °F}Humidity 30% to 90% RH (No condensation)SoftwareInstalled OS*39 Genuine Windows® 7 Professional 32-bit Service Pack 1 / Genuine Windows® 7 Professional 64-bit Service Pack 1Pre-installed Software Adobe Reader, PC Information Viewer, Intel® PROSet/Wireless Software*13, Bluetooth™ Stack for Windows® by TOSHIBA*14, Wireless Switch Utility, Wireless Connection Disable Utility*13 *15 *40, Hotkey Settings, Battery Recalibration Utility, Infineon TPM Professional Package*19 *40, Protector Suite 2011*30 *40, Aptio Setup Utility, PC-Diagnostic Utility, Roxio Creator LJB, CyberLink PowerDVD 10, Wireless WAN Connection Manager*15, Display Selector, Concealed Mode Utility, Wireless Manager Mobile Edition 5.5f*40 *41, Hard Disk Data Erase Utility*42, Recovery Disc Creation Utility, Dashboard for Panasonic PC, Quick Boot Manager, Power Plan Extension Utility, Camera Utility*32, GPS Viewer*16Main SpecificationsModel No. CF-53JALZYDM CF-53JSLZYDMDFQW5645ZAT_CF-53mk2_7_OI_M.book 29 ページ２０１２年５月８日　火曜日　午後６時１１分$

$30SpecificationsGetting StartedUseful InformationTroubleshootingAppendix*1 1 KB = 1,024 bytes / 1 MB = 1,048,576 bytes / 1 GB = 1,073,741,824 bytes*2 Memory size of the factory default depends on the model. You can physically expand the memory up to 16 GB, but the total amount of usable memory available will be less depend-ing on the actual system configuration.*3A segment of the main memory is allotted automatically depending on the computer’s operating status. The size of the Video Memory cannot be set by the user. The size of Video memory is allotted depending on the operating system.*4 1 MB = 1,000,000 bytes / 1 GB = 1,000,000,000 bytes. Your operating system or some application software will report as fewer GB.*5 Data transfer speeds indicate values measured by Pana-sonic Corporation. The data transfer rate of DVD per 1X speed is 1,350 KB/s. The data transfer rate of CD per 1X speed is 150 KB/s.*6 Performance of CD-R, CD-RW, DVD-RAM, DVD-R, DVD-R DL, DVD-RW, +R, +R DL, and +RW cannot be guaranteed depending on writing status and recording format. Also, some data cannot be played back depending on the disc, settings, and environment being used. Does not support writ-ing to DVD-R DL/+R DL (dual layer discs) and Ultra-Speed CD-RW.*7 If an unbalanced disc (e.g., a disc with which the balance has been displaced from the center) is inserted, the speed may become slower if there are large vibrations while the disc is rotating.*8 Only non-cartridge type or removable cartridge type can be used.*9 DVD-R is compatible with 4.7 GB (for General) playback. DVD-R (for Authoring) playback is compatible with discs recorded using Disc-at-Once recording.*10 Depending on the disc, the writing speed may become slower.*11 A 16,777,216 color display is achieved by using the dithering function.*12 Display may be impossible using some connected external displays.*13 Only for model with wireless LAN.*14 Only for model with Bluetooth.*15 Only for model with wireless WAN. The specification may dif-fer depending on models.*16 Only for model with GPS.*17 Only for model with 2nd LAN.*18 Only for model with modem.*19 Only for model with TPM. For information on TPM, refer to the Installation Manual of “Trusted Platform Module (TPM)” by the following procedure.Click (Start) and input "c:\util\drivers\tpm\index.hta" in [Search programs and files] and press Enter.*20 Only for model with 1 PC card slot.*21 Only for model with 2 PC card slots.*22 Only for model with ExpressCard slot.*23 This slot is compatible with High-Speed Mode. Operation has been tested and confirmed using Panasonic SD/SDHC/SDXC Memory Cards with a capacity of up to 64 GB. Opera-tion on other SD equipment is not guaranteed.*24 Only for model with Smart Card slot.Wireless LAN *13Data Transfer Rates IEEE802.11a : 54/48/36/24/18/12/9/6 Mbps (automatically switched)*43IEEE802.11b : 11/5.5/2/1 Mbps (automatically switched)*43IEEE802.11g : 54/48/36/24/18/12/9/6 Mbps (automatically switched)*43IEEE802.11n*44 : (HT20)GI*45 = 400ns:150/130/115/86/72/65/57/43/39/28/21/14/7 Mbps (auto-matically switched)*43GI*45 = 800ns: 130/117/104/78/65/58/52/39/26/19/13/6 Mbps*43(HT40)GI*45 = 400ns: 300/270/240/180/150/135/120/90/60/45/30/15Mbps (automatically switched)*43GI*45 = 800ns:270/243/216/162/135/121/108/81/54/40/27/13Mbps*43Standards Supported IEEE802.11a / IEEE802.11b / IEEE802.11g / IEEE802.11nTransmission Method OFDM system, DS-SS systemWireless Channels Used IEEE802.11a : Channels 36/40/44/48/52/56/60/64/100/104/108/112/116/132/136/140/149/153/157/161/165IEEE802.11b/IEEE802.11g : Channels 1 to 11IEEE802.11n : Channels 1-11/36/40/44/48/52/56/60/64/100/104/108/112/116/132/136/140/149/153/157/161/165RF Frequency Band IEEE802.11a : 5.18 GHz - 5.32 GHz, 5.5 GHz - 5.7 GHz, 5.745 GHz - 5.825 GHzIEEE802.11b/IEEE802.11g : 2.412 GHz - 2.462 GHzIEEE802.11n : 2.412 GHz - 2.462 GHz, 5.18 GHz - 5.32 GHz, 5.5 GHz - 5.7 GHz, 5.745 GHz - 5.825 GHzBluetooth™ *14Bluetooth Version Version 4.0Classic model / Low Energy modelTransmission Method FHSS systemWireless Channels Used 79 channels / Channel 0 to 39RF Frequency Band 2.402 GHz - 2.480 GHzDFQW5645ZAT_CF-53mk2_7_OI_M.book 30 ページ２０１２年５月８日　火曜日　午後６時１１分$

$31Getting StartedUseful InformationTroubleshootingAppendix*25 Does not guarantee operation of all USB-compatible periph-erals.*26 Only for model without 2nd LAN.*27 Does not guarantee operation of all HDMI-compatible periph-erals.*28 Only for model with IEEE 1394a interface.*29 Only for model with rugged USB 2.0 port.*30 Only for model with Fingerprint reader.*31 Only for model with RFID reader.*32 Only for model with Camera.*33 <Only for North America>The AC adaptor is compatible with power sources up to 240V AC adaptor. This computer is supplied with a 125 V AC compatible AC cord. 20-M-2-1*34 Measured with LCD brightness : 60 cd/m2 Varies depending on the usage conditions, or when an optional device is attached.*35 Varies depending on the usage conditions, CPU speed, etc.*36 Approx. 0.7 W when the battery pack is fully charged (or not being charged) and the computer is off.<When using with 115 V AC>Even when the AC adaptor is not connected to the computer, power is consumed (Max. 0.2 W) simply by having the AC adaptor plugged into an AC outlet.*37 Rated power consumption. 23-E-1*38 Do not expose the skin to this product when using the prod-uct in a hot or cold environment. (Î page 9)When using in hot or cold environment, some peripherals may fail to work properly. Check the operation environment of the peripherals.Using this product continuously in a hot environment will shorten the product life. Avoid use in these types of environ-ments.When using in low temperature environment, startup may become slow or battery operation time may become short. The computer consumes power when the hard disk is warm-ing up during startup. Therefore, if you are using battery power and the remaining power is low, the computer may not start up.*39 Operations of this computer are not guaranteed except for the pre-installed OS and the OS which is installed by using the Recovery disc. Some parts of the software in the Recov-ery disc may not be installed depending on a model.*40 Must be installed before use.*41 For information on Wireless Manager, refer to the “Supple-mentary Instructions for Wireless Manager mobile edition 5.5” by the following procedure.Click (Start) and input “c:\util\wlprjct\SupplementaryInstructions.pdf” in [Search programs and files] and press Enter.*42 Perform on the recovery partition. (If this software can not be performed.)*43 These are speeds specified in IEEE802.11a+b+g+n stan-dards. Actual speeds may differ.*44 Available when set to “WPA-PSK”, “WPA2-PSK” or “none”.*45 Only available when HT40 enabled by the computer.DFQW5645ZAT_CF-53mk2_7_OI_M.book 31 ページ２０１２年５月８日　火曜日　午後６時１１分$

Panasonic of North America 9TGWL12B 1x1 802.11 b/g/n PCle Module User Manual DFQW5645ZAT CF 53mk2 7 OI M

Panasonic Corporation of North America 1x1 802.11 b/g/n PCle Module DFQW5645ZAT CF 53mk2 7 OI M

User manual

Navigation menu

Namespaces

Views

Navigation