Panasonic of North America SB-NE5 Wireless Speaker System User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1888950
Application ID	CX6bNFpZoUT9qCwQD2NBQQ==
Document Description	Short Term Confidentiality_User Manual[SC-NE5] -1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	273.62kB (3420253 bits)
Date Submitted	2013-01-29 00:00:00
Date Available	2013-03-15 00:00:00
Creation Date	2013-01-17 11:08:10
Producing Software	Acrobat Distiller 8.3.1 (Windows)
Document Lastmod	2013-01-21 22:57:09
Document Title	untitled

1 ページ ２０１３年１月１７日
木曜日
午前１１時７分
Owner’s Manual
Wireless Speaker System
ESPAÑOL
Model No. SC-NE5
ENGLISH
PPC_SC-NE5~VQT4U55.book
Thank you for purchasing this product.
Please read these instructions carefully before using this product, and save this manual for future
use.
If you have any questions, contact:
U.S.A. and Puerto Rico: 1-800-211-PANA (7262)
Canada: 1-800-561-5505
Register online at www.panasonic.com/register (U.S. customers only)
Included Installation Instructions (l 2, 3 and 26, 27)
The installation work should be done by a qualified installation specialist.
Before commencing work, carefully read these installation instructions and the operating
instructions to ensure that installation is performed correctly.
(Please keep these instructions. You may need them when maintaining or moving this system.)
La referencia rápida en español se puede encontrar en la página 29.
PP
VQT4U55
until
2013/03/01
PPC_SC-NE5~VQT4U55.book
2 ページ ２０１３年１月１７日
木曜日
午前１１時７分
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety
instructions listed below. Keep these operating instructions handy for future reference.
Read these instructions.
Keep these instructions.
DO NOT INGEST BATTERY,
Heed all warnings.
CHEMICAL BURN HAZARD
Follow all instructions.
Do not use this apparatus near water.
This product contains a coin/button cell battery. If the coin/
Clean only with dry cloth.
button cell battery is swallowed, it can cause severe
Do not block any ventilation openings. Install in
internal burns in just 2 hours and can lead to death.
accordance with the manufacturer’s instructions.
Keep new and used batteries away from children. If the
Do not install near any heat sources such as radiators,
battery compartment does not close securely, stop using
heat registers, stoves, or other apparatus (including
the product and keep it away from children.
amplifiers) that produce heat.
If you think batteries might have been swallowed or placed
Do not defeat the safety purpose of the polarized or
inside any part of the body, seek immediate medical attention.
grounding-type plug. A polarized plug has two blades with
If any electrolyte should come into contact with your hands
one wider than the other. A grounding-type plug has two
or clothes, wash it off thoroughly with water.
blades and a third grounding prong. The wide blade or the
If any electrolyte should come into contact with your eyes,
third prong are provided for your safety. If the provided
never rub the eyes. Rinse eyes thoroughly with water, and
plug does not fit into your outlet, consult an electrician for
then consult a doctor.
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the
This product contains a CR Coin Cell Lithium Battery which
point where they exit from the apparatus.
contains Perchlorate Material s special handling may apply.
11 Only use attachments/accessories specified by the
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
CAUTION
manufacturer, or sold with the
apparatus. When a cart is used, use
Unit
caution when moving the cart/apparatus
≥ This unit utilizes a laser. Use of controls or adjustments or
combination to avoid injury from
performance of procedures other than those specified herein
tip-over.
may result in hazardous radiation exposure.
13 Unplug this apparatus during lightning storms or when
≥ Do not place sources of naked flames, such as lighted
unused for long periods of time.
candles, on this unit.
14 Refer all servicing to qualified service personnel. Servicing
Placement
is required when the apparatus has been damaged in any
≥ To reduce the risk of fire, electric shock or product damage,
way, such as power-supply cord or plug is damaged, liquid
– Do not install or place this unit in a bookcase, built-in
has been spilled or objects have fallen into the apparatus,
cabinet or in another confined space. Ensure this unit is
the apparatus has been exposed to rain or moisture, does
well ventilated.
not operate normally, or has been dropped.
– Do not obstruct this unit’s ventilation openings with
newspapers, tablecloths, curtains, and similar items.
≥ Keep your speakers at least 10 mm (13/32q) away from the
WARNING
system for proper ventilation.
Unit
≥ To reduce the risk of fire, electric shock or product damage,
– Do not expose this unit to rain, moisture, dripping or
splashing.
– Do not place objects filled with liquids, such as vases, on
this unit.
– Use only the recommended accessories.
– Do not remove covers.
– Do not repair this unit by yourself. Refer servicing to
qualified service personnel.
AC power supply cord
≥ The power plug is the disconnecting device.
Install this unit so that the power plug can be unplugged from
the socket outlet immediately.
Button-type battery (Lithium battery)
≥ Risk of fire, explosion and burns. Do not disassemble, heat
above 60 oC (140 oF) or incinerate.
VQT4U55
Button-type battery (Lithium battery)
≥ Danger of explosion if battery is incorrectly replaced. Replace
only with the type recommended by the manufacturer.
≥ Keep out of reach of children.
≥ Insert with poles aligned.
≥ Mishandling of batteries can cause electrolyte leakage and
may cause a fire.
– Remove batteries if you do not intend to use the remote
control for a long period of time. Store in a cool, dark place.
– Do not heat or expose to flame.
– Do not leave the battery(ies) in a car exposed to direct sunlight
for a long period of time with doors and windows closed.
– Do not touch the terminals (i and j) with metal objects.
– Do not recharge, disassemble, remodel, heat or throw into fire.
≥ When disposing the batteries, please contact your local
authorities or dealer and ask for the correct method of
disposal.
3 ページ ２０１３年１月１７日
THE FOLLOWING APPLIES ONLY IN THE
U.S.A.
FCC Note:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and
receiver.
≥ Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
≥ Consult the dealer or an experienced radio/TV technician
for help.
Any unauthorized changes or modifications to this
equipment would void the user’s authority to operate this
device.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way,
Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Marketing Company of
North America
Telephone No.: 1-800-211-PANA (7262)
THE FOLLOWING APPLIES IN THE U.S.A.
AND CANADA
This device complies with Part 15 of FCC Rules and
RSS-Gen of IC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of this
device.
FCC ID: ACJ-SB-NE5 (SB-NE5) / ACJ-SL-NE5 (SL-NE5)
IC: 216A-SBNE5 (SB-NE5) / 216A-SLNE5 (SL-NE5)
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
This equipment complies with FCC/IC radiation exposure
limits set forth for an uncontrolled environment and meets
the FCC radio frequency (RF) Exposure Guidelines in
Supplement C to OET65 and RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment has very
low levels of RF energy that is deemed to comply without
maximum permissive exposure evaluation (MPE). But it is
desirable that it should be installed and operated keeping
the radiator at least 20 cm (7 7/8q) or more away from
person’s body (excluding extremities: hands, wrists, feet
and ankles).
木曜日
午前１１時７分
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
ENGLISH
PPC_SC-NE5~VQT4U55.book
(Bottom of product)
(Bottom of product)
Product Identification Marking is located on the bottoms of
the CD unit and the speaker unit.
AndroidTM, Google PlayTM, Google ChromeTM browser are
trademarks or registered trademarks of Google Inc.
VQT4U55
PPC_SC-NE5~VQT4U55.book
4 ページ ２０１３年１月１７日
Table of contents
IMPORTANT SAFETY INSTRUCTIONS ........... 2
Supplied items .................................................. 4
Unit and media care.......................................... 5
Playable media.................................................. 5
Control reference guide ................................... 6
Connections ...................................................... 8
Inserting media ................................................. 9
Network settings............................................. 10
Using AirPlay with this system’s speakers ......... 14
Playing back music files on the DLNA server ..... 15
Bluetooth® operations .................................... 16
About Bluetooth® ............................................ 17
Media playback operations............................ 17
Listening to the radio ..................................... 19
Sound adjustment .......................................... 20
Clock and Timer.............................................. 20
Others .............................................................. 21
Troubleshooting.............................................. 23
Attaching the speaker unit to a wall
(optional) ...................................................... 26
Specifications ................................................. 28
Spanish Quick Reference /
Referencia rápida en español..................... 29
Limited Warranty
(ONLY FOR U.S.A. AND PUERTO RICO).... 30
Limited Warranty (ONLY FOR CANADA) ...... 31
About descriptions in this Owner’s Manual
≥ Pages to be referred to are indicated as “l ±±”
≥ Unless otherwise indicated, operations are
described using the remote control.
VQT4U55
木曜日
午前１１時７分
Supplied items
This system (SC-NE5)
∏ 1 CD unit
(SL-NE5)
∏ 1 Speaker unit
(SB-NE5)
Accessories
Check the supplied accessories before using this
system.
∏ 1 Remote control ∏ 1 FM indoor
(with a battery)
antenna
(N2QAYC000089)
(RSAXC0002)
∏ 2 AC power supply
cords
(K2CB2CB00022)
Wall mounting accessories
∏ 1 Safety holder
(RGQ0660-K)
∏ 2 Wall mount
brackets
(RMQX1082-S)
∏ 1 Screw
(XTB3+8JFJK-J)
(ONLY FOR CANADA)
The enclosed Canadian French label sheet corresponds to the
English display on the unit.
≥ Do not use AC power supply cord with other equipment.
≥ Product numbers provided in this Owner’s Manual are
correct as of February 2013. These may be subject to
change.
5 ページ ２０１３年１月１７日
Unit and media care
Pull out the AC power plug from the outlet before
maintenance.
∫ Clean this system with a soft, dry cloth
≥ When dirt is heavy, wring a cloth moistened in water tightly to
wipe the dirt, and then wipe it with a dry cloth.
≥ Never use alcohol, paint thinner or benzine to clean this
system.
≥ Before using chemically treated cloth, carefully read the
instructions that came with the cloth.
木曜日
午前１１時７分
Playable media
Compatible iPod/iPhone/iPad
Compatible with “IPOD_DOCK” connection
(Using Lightning connector)
iPod touch (5th generation)
iPod nano (7th generation)
iPhone 5
ENGLISH
PPC_SC-NE5~VQT4U55.book
Compatible with “IPOD_PORT” connection
[Using dedicated USB cable (not supplied)]
∫ Maintenance of the lens
≥ Clean the lens regularly to prevent malfunctions. Use a
blower to remove dust and a cotton swab if it is extremely
dirty.
≥ You cannot use a CD type lens cleaner.
≥ Do not leave the door open for prolonged periods of time.
This will cause the lens to get dirty.
≥ Be careful not to touch the lens with your fingers.
iPod touch
1st, 2nd, 3rd, 4th, and 5th generation
iPod nano
2nd, 3rd, 4th, 5th, 6th, and 7th generation
iPhone 5 / iPhone 4S / iPhone 4 / iPhone 3GS /
iPhone 3G / iPhone
iPad (3rd, and 4th generation) / iPad 2 / iPad
iPad mini
Lens
≥ Compatibility depends on the software version. Update your iPod/
iPhone/iPad to the latest software before using it with this system.
≥ Please be aware that Panasonic accepts no responsibility for
the loss of data and/or information.
∫ Clean discs
DO
(as of February 2013)
DO NOT
Compatible CD
≥ A disc with the CD Logo.
Wipe with a damp cloth and then wipe dry.
∫ Disc handling precautions
≥ Handle discs by the edges to avoid inadvertent scratches or
fingerprints on the disc.
≥ Do not attach labels or stickers to discs.
≥ Do not use record cleaning sprays, benzine, thinner, static
electricity prevention liquids or any other solvent.
≥ Do not use the following discs:
– Discs with exposed adhesive from removed stickers or
labels (rented discs etc.).
– Discs that are badly warped or cracked.
– Irregularly shaped discs, such as heart shapes.
∫ To dispose or transfer this system
This system may keep the user settings information
internally. If you discard this system either by disposal
or transfer, then follow the procedure to return all the
settings to the factory presets to delete the user
settings.
(l 23, “To return all settings to the factory preset”)
≥ The operation history may be recorded in the
memory of this system.
≥ This system can play back discs that conform to the CD-DA format.
≥ This system may not be able to play some discs due to the
condition of the recording.
≥ This system cannot play back MP3 files.
Note about using a DualDisc
≥ The digital audio content side of a DualDisc does not meet
the technical specifications of the Compact Disc Digital Audio
(CD-DA) format so play may not be possible.
≥ Do not use a DualDisc in this system as it may not be possible to
insert it correctly and it may get scratched or scraped.
Compatible AirPlay devices
iOS 4.3.3 or later
iPod touch
3rd, 4th, and 5th generation
iPhone 5 / iPhone 4S / iPhone 4 / iPhone 3GS
iPad (3rd, and 4th generation) / iPad 2 / iPad
iPad mini
iTunes 10.2.2 or later (Mac / PC)
(as of February 2013)
VQT4U55
PPC_SC-NE5~VQT4U55.book
6 ページ ２０１３年１月１７日
木曜日
午前１１時７分
Control reference guide
This system consists of the CD unit and the speaker unit. The both units are wirelessly connected when
turned on.
∫ CD unit
Side view
11
10
∫ Speaker unit
8 11
Top view
13
− VOLUME ＋
2 12
VQT4U55
Standby/on switch (Í/I)
Press to switch the unit from on to standby mode or vice
versa.
In standby mode, the unit is still consuming a small
amount of power.
≥ The CD unit and the speaker unit operate
simultaneously. Press either standby/on switch to turn
both units on or to standby mode.
Refer to page 23 when the units do not turn on
simultaneously.
Select the audio source
“CD” --. “FM” --. “BLUETOOTH” --. “AUX”
^ “IPOD_PORT” ( “IPOD_DOCK”(b
Basic playback control buttons
iPod port for iPod/iPhone/iPad (l 5, 9)
Adjust the volume (0 (min) to 50 (max))
Network setup button (l 11)
Standby/on indicator
While this system is turned on:
The indicator lights in green when the CD unit
and the speaker unit are connected
successfully, blinks in green when they are
connecting, and lights in red when they fail to
connect.
8 Display
9 Open the CD lid
10 Dock for iPod/iPhone with Lightning connector
(l 9)
11 Remote control signal sensor
Distance: Within approx. 7 m (23 ft) directly in front.
≥ To avoid interference, please do not put any objects in
front of signal sensor.
12 WPS pairing button (l 10)
13 Wi-Fi® status indicator
PPC_SC-NE5~VQT4U55.book
7 ページ ２０１３年１月１７日
木曜日
午前１１時７分
– Keep a minimum distance of 1 cm (3/8q) between the CD unit and the speaker unit when placing them.
– The distance between the CD unit and the speaker unit should be a maximum of 10 m (33 ft). The range can decrease
depending on the environment, obstacles or interference.
– This system may not function properly and troubles such as noise and sound jumps may arise due to radio wave interference
if this system is located too close to the devices that use the 2.4 GHz band.
– This system may not function properly if radio waves from a nearby broadcasting station, etc. is too strong.
– Do not use this system near equipment or in an environment that is sensitive to radio frequency interference (example:
airports, hospitals, laboratories, etc).
ENGLISH
≥The CD unit’s display turns off if the CD unit is left unused for more than 3 minutes and the audio selector is set
to an option other than “CD”, “IPOD_DOCK”, or “IPOD_PORT”. To turn the display on, press any button on
the CD unit, or select “CD”, “IPOD_DOCK”, or “IPOD_PORT” as an audio source.
≥Placing the CD unit and the speaker unit:
∫ Remote control
SLEEP DIMMER
AUX
iPod
CD/
RADIO
VOL
[ , AUX] : “BLUETOOTH” ,. “AUX”
Basic playback control buttons
Enter setup menu
Enter the iPod/iPhone menu /
Change displayed information
6 Set the sleep timer
7 Change the brightness of the display panel
≥ Press to dim the display panel.
Press again to cancel.
8 Adjust the volume (0 (min) to 50 (max))
9 Mute the sound
Mutes the sound. Press again to cancel.
“MUTE” is also canceled when the volume is
adjusted or this system is turned off.
10 Enter playback menu
11 Enter sound menu
12 Selection/OK
VOL
MUTE
SETUP
Turn this system on or off
Select the audio source
[iPod] : “IPOD_DOCK” ,. “IPOD_PORT”
[CD/RADIO] : “CD” ,. “FM”
iPod MENU SOUND PLAY MENU
DISPLAY
OK
∫ Before using for the first time
Remove the insulation sheet A.
∫ To replace a button-type battery
Battery type: CR2025 (Lithium battery)


≥ Set the button-type battery with its (i) mark
facing upward.
≥ Keep the button-type battery out of reach of
children to prevent swallowing.
VQT4U55
PPC_SC-NE5~VQT4U55.book
8 ページ ２０１３年１月１７日
木曜日
午前１１時７分
Connections
Basic connection
Connect the FM indoor antenna (supplied) to
the speaker unit.
Connect an external music
device (for AUX mode)
Audio cable
(not supplied)
1 Plug the audio cable (not supplied) into the
AUX jack.
Plug type: ‰3.5 mm (1/8q) stereo
2 Press [ , AUX] to select “AUX” and start
playback on the connected device.
Adhesive tape
(not supplied)
To select the sound input level of the
external device
FM indoor antenna
(supplied)
1 While in AUX mode, press [PLAY MENU] to
select “INPUT LEVEL” and then press [OK].
2 Press [3, 4] to select “NORMAL” or “HIGH”.
Connect the AC power supply cord after all
other connections are completed.
≥ The default setting is “NORMAL”.
≥ Switch the equalizer off or turn the volume of the external
device down to reduce the input signal. High level of input
signal will distort the sound.
≥ For details, refer to the instruction manual of the other equipment.
≥ The cables and the devices are not supplied.
Connect the CD unit and the
speaker unit with cables (optional)
AC power supply
cord (supplied)
To household AC outlet
≥ After connecting the AC power supply cord to the AC outlet,
wait for more than 15 seconds to turn on the Standby/on
switch.
≥ When this system is turned on, the CD unit and the speaker
unit are connected wirelessly.
≥ When this system is turned on for the first time after
purchase, a message prompting you to connect a Bluetooth®
device (“PAIRING”) is displayed. (l 16)
≥ This system consumes a small amount of AC power (l 28)
even when turned off.
≥ In the interest of power conservation, if you will not be using
this system for an extended period of time, unplug it from the
household AC outlet.
If the CD unit and the speaker unit are not
wirelessly connected, or the output sound is
interrupted, connect the both units with two audio
cables (plug type: ‰3.5 mm (1/8q) stereo, not
supplied) as illustrated below.
≥ We recommend you use cables of less than 5 m
(16.4 ft).
Audio cable (not supplied)
≥ These speakers do not have magnetic shielding. Do not
place them near a television, personal computer or other
devices easily influenced by magnetism.
≥ Tape the antenna to a wall or column in a position with the
least amount of interference. (Use an FM outdoor antenna if
radio reception is poor.)
VQT4U55
≥ If the cables are connected, the displays show
“WIRED MODE” and this system starts wired
communication. This system automatically
connects wirelessly when the cables are
disconnected.
PPC_SC-NE5~VQT4U55.book
9 ページ ２０１３年１月１７日
木曜日
午前１１時７分
Inserting media
Inserting a disc
Select “CD” as the source.

10 cm (4q)
ENGLISH

The label side
1 Press [CD <] to open the lid on the back of the CD unit.
≥ Leave a space more than 10 cm (4q) behind the unit.
≥ Do not place any objects behind the unit.
2 While holding the unit, push the centre of the CD until it clicks into place, and then close the CD lid.
≥ Be careful not to scratch the CD.
≥ Make sure you place the centre of the CD onto the CD spindle of the unit.
Note: Remove the CD only after it stops rotating.
Connect an iPod/iPhone/iPad*1, 2
Select “IPOD_PORT” as the source.
≥ When connecting an iPod/iPhone/iPad, use the dedicated
USB cable (not supplied).
Connect an iPod/iPhone with
Lightning connector*1
Select “IPOD_DOCK” as the source.
*3
∫ Charging an iPod/iPhone/iPad*4
Charging starts when an iPod*2/iPhone/iPad is
connected to this unit.
≥ During standby mode, charging will not start from the USB
cable connection, however it will start as usual from the
Lightning connector.
– To charge from the USB cable connection, start the charging
before turning this unit to standby mode.
≥ Check the iPod/iPhone/iPad to see if the battery is fully
charged. (Once fully recharged, additional recharging will not
occur.)
≥ If this unit is switched to standby mode “IPOD CHARGING” is
shown on the unit’s display.
≥ Make sure that the unit does not fall when inserting or
removing media.
≥ When moving this unit, be sure to remove all media and turn
this unit to standby mode.
*1: Refer to “Playable media” for compatible models. (l 5)
*2: When using the “IPOD_PORT” connection, do not connect
the following models to this unit:
– iPod classic, iPod [4th (colour display), and 5th (video)
generation], iPod nano (1st generation)
Unexpected behavior may occur.
*3: When using the “IPOD_DOCK” connection:
≥ Be sure to remove the iPod/iPhone from its case.
≥ Make sure that the iPod/iPhone is fully inserted and its
back is resting against the cushion pad.
≥ Make sure to hold the dock when removing the iPod/
iPhone.
≥ Make sure to close the dock properly after using it. If
not, the standby power consumption will increase.
*4: Use the “IPOD_PORT” connection to charge the iPad.
VQT4U55
PPC_SC-NE5~VQT4U55.book
10 ページ ２０１３年１月１７日
木曜日
午前１１時７分
Network settings
You can wirelessly stream music from an iOS
device (iPhone, iPod, iPad), an Android device or a
Mac/PC to this system’s speakers by using the
AirPlay or DLNA feature.
To use these features, this system must join the
same 2.4 GHz wireless network as the AirPlay
compatible device (l 5) or the DLNA compatible
device.
≥ It is also possible to use AirPlay without a wireless network
router. (l 14, “Directly streaming to this system (AirPlay)”)
≥ To cancel this setting in the middle, press [Í] to turn off this
system.
≥ Simultaneous use with other 2.4 GHz devices, such as
microwaves, cordless telephones, etc., may result in
connection interruptions.
≥ For up to date compatibility information on your wireless
network router refer to
http://panasonic.jp/support/global/cs/
(This site is in English only.)
Method 1
If your wireless network router supports WPS
(Wi-Fi Protected SetupTM).
∫ Using the WPS Push Button
Configuration (PBC)
The WPS identifier mark
WPS Push Button
Configuration (PBC)
compatible wireless network
router may have this mark.
Preparation
≥ Place this system close to the wireless network
router.
Turn this system on.
Follow the chart below to choose the network
setting method.
Does your wireless network router
support WPS?
Yes
No / Do not know
l right,
“Method 1”
Are you using an
iPod touch/iPhone/iPad?
Is the iOS version 5.0 or later?
Yes
Press and hold [s WPS] on the speaker unit.
{. “WPS” flashes on the display.
(The Wi-Fi status indicator blinks blue.)
≥ Complete step 2 within 2 mins.
After “WPS” is indicated, press the WPS button
on the wireless network router.
The settings are completed when “SUCCESS”
is displayed and the Wi-Fi status indicator
stops blinking and lights in blue.
“FAIL” may be displayed if the connection was
not made within the set time limit. Try the setting
again. If “FAIL” is still displayed, try other
methods on page 11 or 12.
Press [OK] on the remote control to exit the
setting.
No
≥ To use the WPS PIN code, refer to the notes on page 13.
l 11,
“Method 2”
l 12,
“Method 3”
≥ If you want to perform wireless setting with
your Mac/PC, or you want to apply the
advanced setting, try “Method 4” on page 12.
10
VQT4U55
11 ページ ２０１３年１月１７日
Method 2
If you're using an iPod touch/iPhone/iPad.
(iOS version 5.0 or later.)
With this method you will share the wireless
network settings of your iPod touch/iPhone/iPad
with this system.
≥ The following explanations are based on an iPhone.
Disconnect any devices connected to the CD
unit.
Connect the iPhone to your home wireless
network.
木曜日
午前１１時７分
Press [OK] on the remote control to exit the
settings.
*1: Depending on the network environment or the wireless
network router settings, it may take more than 10 mins. to
complete the settings.
ENGLISH
PPC_SC-NE5~VQT4U55.book
3 Connect the iPhone to the CD unit.
Choose one of the following connections.
“IPOD_DOCK” connection compatible
iPod touch/iPhone:
iPod touch/iPhone/iPad with iOS 5.0 or later:
Connect to the iPod port on the side of the CD
unit with a dedicated USB cable.
Unlock your iPhone and then press and hold
[sNETWORK SETUP] on the CD unit for more
than 3 seconds.
≥ If “NOT SUPPORTED” or “SET WI-FI” is displayed,
check that the iPhone is connected to the wireless
network and try again from step 1.
A message will pop-up on your iPhone.
Allow the iPhone to share the wireless network
settings.*1
{. The Wi-Fi status indicator blinks.
The settings are completed when “SUCCESS”
is displayed and the Wi-Fi status indicator
stops blinking and lights in blue.
If “FAIL” is displayed press [OK] and try the
setting again. If “FAIL” is still displayed, try other
methods on page 10 or 12.
≥ If the iPhone was disconnected midway through, try again
without disconnecting it.
11
VQT4U55
PPC_SC-NE5~VQT4U55.book
12 ページ ２０１３年１月１７日
木曜日
午前１１時７分
Method 3
Method 4
Setting the network connection with the smartphone app.
Setting the network connection from an Internet
browser.
You can make the wireless network settings with
the app, “Panasonic Stereo System Network Setup”
(for free).
If you’re using an Android device, download the app
at the Google Play Store. If you’re using an iPod
touch/iPhone/iPad, download it at the App Store.
With this method, you will access this system’s
wireless network settings from the Internet browser
of your compatible device.
≥ The following explanations are based on an
iPhone.
Preparation
≥ Connect your smartphone to your home wireless
network.
≥ Check the password for your home wireless
network.
Press [SETUP] on the remote control repeatedly
to select “NET SETUP” and then press [OK].
{. “SETTING” is indicated on the display.
(The Wi-Fi status indicator blinks purple.)
{. “SETTING” is indicated on the display.
(The Wi-Fi status indicator blinks purple.)
Press [SETUP] on the remote control
repeatedly to select “NET SETUP” and then
press [OK].
After “SETTING” is indicated, connect your
compatible device to this system’s wireless
network named “00 Setup _ _ _ _ _ _”.
≥ “ _ ” stands for a digit that is unique to each set.
≥ Make sure that DHCP is enabled for the network setting
on your compatible device.
Start “Panasonic Stereo System Network
Setup” on your smartphone and follow the
indications.
∫ Note for the iOS version
After step 2
1 Enter the password for the home wireless
network to which the iOS device is connected.
2 When a message instructing you to connect the
iOS device to this system is displayed, press
the home button to close the app.
3 On the Wi-Fi network selection screen in
“Settings”, select “00 Setup _ _ _ _ _ _”.
Start the Internet browser on your compatible
device and type “http://192.168.1.12/” into the
URL address field and display the page.
≥ “ _ ” stands for a digit that is unique to each set.
{. This system’s setup window is displayed.
12
When a message indicating the completion of
the connection to this system is displayed,
restart the app.
When a message indicating the completion of the
Wi-Fi setup of this system is displayed, close the
app, and then check the operation of AirPlay, etc.
≥ “Panasonic Stereo System Network Setup” for Mac OS is
also available at the App Store.
VQT4U55
≥ Examples of Internet browsers
iOS device/Mac : Safari
Android device : Google Chrome browser
PC : Windows Internet Explorer
Select “Search wireless network”.
5
13 ページ ２０１３年１月１７日
[1] Select your home wireless network name.*1
[2] Type the password.
Select “JOIN” to apply the settings.
≥ In the pop-up screen, select “OK” to continue.
– Select “Cancel” to return to the setup window.
The settings are completed when “SUCCESS”
is displayed and the Wi-Fi status indicator
stops blinking and lights in blue.
If “FAIL” is displayed press [OK], check the
wireless network password and other settings
and start again from step 1.
Make sure to connect your compatible device
back to your home wireless network.
*1: If you have set your wireless network to be invisible, select
“BACK” and refer to “Alternative settings”.
午前１１時７分
Advanced network settings
Select and input the details.
≥ Check your home wireless network name (Network
name (SSID)) and password for this network. This can
often be found on the wireless network router itself.
木曜日
≥ The below settings are the alternative or additional settings
for “Method 4”. (l 12)
Alternative settings
Instead of steps 4 and 5
Select “Manual settings”.
1 Type your home wireless network name
into the “Network name (SSID)” field.
2 Select the encryption method from the
“Security system” drop down list.
3 Type the password into the “Password” field
and then select “JOIN”.
ENGLISH
PPC_SC-NE5~VQT4U55.book
Additional settings
If your home wireless network has been
configured to use specific IP Addresses, Subnet
Mask, Default Gateway, Primary DNS, etc.
Before step 6
Select “Advanced network settings”.
{. Input the required addresses into each field and select
“JOIN”.
≥ To change the settings back to DHCP, select “ON” from the
“DHCP” drop down list.
If you want to change the name of this system
that is displayed as the AirPlay speakers or
DLNA renderer.
Before step 4
Select “Additional settings”.
1 Select “Edit STEREO SYSTEM name”.
2 Type a new name into the
“STEREO SYSTEM name” field.
{. Only ASCII characters can be used.
Select “OK”.
If this system is already connected to your
home wireless network:
jSelect “Additional settings” and then
select “Exit”.
If this system is not connected to your home
wireless network:
jContinue to step 4 of “Method 4”.
≥ Enable Java and Cookies in your browser settings.
≥ This system can also be set using the WPS PIN code.
Replace step 2 of “Method 1” with the following steps.
(Before starting, refer to the wireless network router’s
operating instructions for details on how to enter the PIN
code.)
While “WPS” is flashing press and hold [s WPS] again
to display the 8 digit PIN code.
{. Wi-Fi status indicator blinks purple.
Enter the PIN code into the wireless network router.
13
VQT4U55
PPC_SC-NE5~VQT4U55.book
14 ページ ２０１３年１月１７日
木曜日
Using AirPlay with this
system’s speakers
Preparation
≥ Complete the network settings. (l 10)
≥ Connect the iOS device or Mac/PC to the same
home wireless network as this system.
Turn this system on.
≥ Check that the Wi-Fi status indicator lights in
blue.
≥ If it doesn’t light in blue, check the wireless
network settings. (l 10)
iOS device: Start the “Music” (or iPod) app.
Mac/PC: Start “iTunes”.
≥ If the Music app on your iOS device is used, select the
audio file you want to play.
Select “Panasonic NE5 _ _ _ _ _ _”*1, 2 from the
AirPlay
icon.
{. Check the volume settings before starting the playback.
(When AirPlay is used for the first time, the volume may
be output at the maximum setting.)
e.g.,
iPhone iOS 6.0.1
午前１１時７分
Directly streaming to this
system (AirPlay)
With this function set to “ON”, you can stream
music from the iOS device or
Mac / PC (iTunes 10.2.2 or later) to this system
without the need of a wireless network router.
≥ Previous network settings will be deleted when
this function is set to “ON”.
≥ The following explanations are based on an
iPhone.
Press [SETUP] repeatedly to select
“D.CONNECT”.
Press [3, 4] to select “ON” and then press
[OK].
Press [3, 4] to select “OK? YES” and then
press [OK].
“PW _ _ _ _ _”*1 is displayed.
The 5 digits after “PW” is the password for this
network.
Connect your iPhone to this system’s wireless
network named “NE5 _ _ _ _ _ _”*2.
NE5
e.g.,
iTunes 11.0
Enter the password that is indicated on this
system’s display.
Once the iPhone is connected to this system’s
wireless network, the setup is competed.
NE5
Start play.
≥ The playback will start with a slight delay.
14
≥ This system can be set to turn on automatically when this
system is selected as the output speakers. (l 22)
≥ Playback of other audio sources will stop and AirPlay output
will have priority.
≥ Volume changes on the iOS device or iTunes will be applied
to this system. (Refer to the iTunes Help for the required
settings in iTunes.)
≥ With some iOS and iTunes versions, it may not be possible
to restart the AirPlay playback if the selector is changed
(e.g., “CD”) or this system is turned off, during the AirPlay
playback.
In this case, select a different device from the AirPlay icon of
the Music App or iTunes and then re-select this system as
the output speakers.
≥ AirPlay will not work when playing back videos on iTunes.
*1: “ _ ” stands for a digit that is unique to each set.
*2: The name that is displayed for this system can be changed
from the “Edit STEREO SYSTEM name” settings.
(l 13, “Advanced network settings”)
VQT4U55
Continue to step 2 of “Using AirPlay with this
system’s speakers”.
≥ This setting is reset to “OFF” when other network settings are
performed. (l 10)
≥ When “D.CONNECT” is set to “ON”, this system will not be
connected to the Internet. It is not possible to update the
software or check the Wi-Fi signal strength.
≥ When AirPlay is not being used, disconnect the AirPlay
compatible device from this network.
≥ When using a computer on this network, make sure that all
the shared files are encrypted.
≥ This feature is only compatible with the “Open System”
authentication method. It is not compatible with “Shared Key”
authentication method.
*1: “ _ ” stands for a digit.
*2: “ _ ” stands for a digit that is unique to each set.
15 ページ ２０１３年１月１７日
Display the password
The first time “D.CONNECT” is set to “ON”, a
password for this system’s wireless network is
randomly created and memorized in this system.
≥ This password is memorized until it is changed.
1 While “D.CONNECT” is set to “ON”:
Press [SETUP] repeatedly to select
“D.CONNECT”.
2 Press [3, 4] to select “ON” and then press
[OK].
3 The current password is displayed.
≥ The 5 digits after “PW” is the password for
this network.
Press any button to exit.
While “D.CONNECT” is set to “OFF”:
Press [SETUP] repeatedly to select
“D.CONNECT”.
Press [3, 4] to select “CHANGE PW” and
then press [OK].
Press [3, 4] to select “OK? YES” and then
press [OK].
The new password is displayed.
≥ The 5 digits after “PW” is the new password
for this network.
Press any button to exit.
∫ Note about changing the password
After changing this system’s wireless network
password, if you are not prompted to change the
password on the other devices, the following
changes are required.
iOS device (iPod touch/iPhone/iPad)*1:
≥ Before choosing this system’s network,
1 Select [ ] located beside this system’s
wireless network name.
2 Select “Forget this Network” and then select
“Forget”.
3 Select this system’s wireless network and enter
the new password.
Mac/PC:
≥ If the computer has memorized the old password,
be sure to change the memorized password for
this system’s wireless network to the new one.
午前１１時７分
Playing back music files on
the DLNA server
You can share music files stored in the DLNA
Certified media server (PC with Windows 7
installed, smartphone, etc.) connected to your
home wireless network, and enjoy the contents with
this system’s speaker.
Preparation
≥ Complete the network settings. (l 10)
≥ Connect your device with DMC (Digital Media
Controller) compatible software installed to the
same home wireless network as this system.
≥ Add the contents and folder to the libraries of the
Windows Media® Player or the smartphone, etc.
– Playlist of Windows Media® Player can play back
only the contents that are stored in the libraries.
Change the password
木曜日
ENGLISH
PPC_SC-NE5~VQT4U55.book
Turn this system on.
≥ Check that the Wi-Fi status indicator lights in
blue.
≥ If it doesn’t light in blue, check the wireless
network settings. (l 10)
Operate the DMC compatible device and
connect to this system.
≥ The device name of this system will be
displayed as “Panasonic NE5 _ _ _ _ _ _”*1, 2.
≥ For details on how to use DMC compatible
devices, refer to the operating instructions of
the devices or the software.
∫ Support format of DLNA client
File formats that are not supported by your DLNA
server cannot be played.
Audio codec
Example of file extension
MP3
WAV
.mp3
.wav
≥ Depending on the contents and the connected equipment,
playback may not be possible.
*1: “ _ ” stands for a digit that is unique to each set.
*2: The name that is displayed for this system can be changed
from the “Edit STEREO SYSTEM name” settings.
(l 13, “Advanced network settings”)
≥ Refer to the devices’s operating instructions for details.
*1: Steps are based on iOS 6.0.1.
15
VQT4U55
PPC_SC-NE5~VQT4U55.book
16 ページ ２０１３年１月１７日
木曜日
午前１１時７分
Bluetooth® operations
By using the Bluetooth® connection, you can listen to the sound from the Bluetooth® audio device from this
system wirelessly.
≥Refer to the operating instructions of the Bluetooth® device for details.
Bluetooth® transmission mode
Pairing Bluetooth® devices
Preparation
≥ Turn on the Bluetooth® feature of the device and
place the device near the speaker unit.
≥ If this system is already connected to a
Bluetooth® device, disconnect it.
Press [ , AUX] to select “BLUETOOTH”.
≥ If “PAIRING” is indicated on the display, go to
step 3.
Press [PLAY MENU] to select “NEW DEV.” and
then press [OK].
Start play on the Bluetooth® device.
Preparation
≥ Turn on the Bluetooth® feature of the device and
place the device near the speaker unit.
≥ If this system is already connected to a
Bluetooth® device, disconnect it.
Press [
VQT4U55
Press [PLAY MENU] repeatedly to select
“LINK MODE”.
Press [3, 4] to select the mode and then
press [OK].
MODE 1: Emphasis on connectivity
MODE 2: Emphasis on sound quality
≥ The default setting is “MODE 1”.
Bluetooth® input level
If the sound input level of the Bluetooth®
transmission is too low, change the input level
setting.
Preparation
≥ Connect a Bluetooth® device.
, AUX] to select “BLUETOOTH”.
Press [PLAY MENU] repeatedly to select
“INPUT LEVEL”.
Press [3, 4] to select the level and then press
[OK].
“LEVEL 0” ,. “LEVEL i1” ,. “LEVEL i2”
^---------------------------------------------------------J
{. “READY” is indicated on the display.
Select “SC-NE5” from the Bluetooth® device’s
Bluetooth® menu.
≥ Select “LEVEL 0” if the sound is distorted.
≥ The default setting is “LEVEL 0”.
{. The name of the connected device is indicated on the
display for 2 seconds.
Disconnecting a Bluetooth®
device
Start play on the Bluetooth® device.
≥ This system can only be connected to one device at a time.
≥ When “BLUETOOTH” is selected as the source, this system
will automatically try and connect to the last connected
Bluetooth® device.
≥ The Bluetooth® device will be disconnected if a different
audio source (e.g., [CD]) is selected.
16
Select “SC-NE5” from the Bluetooth® device’s
Bluetooth® menu.
Connecting a paired Bluetooth®
device
≥ Press [ , AUX] to select “BLUETOOTH”.
≥ If a Bluetooth® device is already connected,
disconnect it.
{. “PAIRING” is indicated on the display.
≥ If prompted for the passkey, input “0000”.
≥ You can register up to 8 devices with this system. If a 9th
device is paired, the device that has not been used for the
longest time will be replaced.
You can change the transmission speed to prioritize
transmission quality or sound quality.
Preparation
While a Bluetooth® device is connected:
Press [PLAY MENU] to select
“DISCONNECT?”.
Press [3, 4] to select “OK? YES” and then
press [OK].

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Create Date                     : 2013:01:17 11:08:10+09:00
Modify Date                     : 2013:01:21 22:57:09+09:00
Metadata Date                   : 2013:01:21 22:57:09+09:00
Trapped                         : False
Producer                        : Acrobat Distiller 8.3.1 (Windows)
Format                          : application/pdf
Title                           : untitled
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Document ID                     : uuid:e2fa3194-4dca-498b-9774-d06e89c13990
Instance ID                     : uuid:754e5705-f914-4126-a626-58483d06b915
Page Count                      : 16

EXIF Metadata provided by EXIF.tools