Panasonic Dmc Ft30 Owners Manual

DMC-FT30 - Basic Owner’s Manual DMC-FT30_UGB_EN Free User Guide for Panasonic Camera, Manual - page1

2015-08-19

: Panasonic Panasonic-Dmc-Ft30-Owners-Manual-792077 panasonic-dmc-ft30-owners-manual-792077 panasonic pdf

Open the PDF directly: View PDF PDF.
Page Count: 28

DownloadPanasonic Panasonic-Dmc-Ft30-Owners-Manual-  Panasonic-dmc-ft30-owners-manual
Open PDF In BrowserView PDF
DMC-FT30EB-SQT0728_mst.book 1 ページ

2014年11月25日 火曜日 午前9時12分

Basic Operating Instructions
Digital Camera
Model No.

DMC-FT30

Please read these instructions carefully before using this
product, and save this manual for future use.
More detailed instructions on the
operation of this camera are
contained in “Operating
Instructions for advanced features
(PDF format)” in the supplied CD-ROM.

Web Site: http://www.panasonic.com
Model number suffix “EB” denotes UK model.

SQT0728

EB

F1214CT0

until
2015/2/10

DMC-FT30EB-SQT0728_mst.book 2 ページ

2014年11月25日 火曜日 午前9時12分

Dear Customer,
We would like to take this opportunity to thank you for purchasing this Panasonic Digital
Camera. Please read these Operating Instructions carefully and keep them handy for
future reference. Please note that the actual controls and components, menu items, etc.
of your Digital Camera may look somewhat different from those shown in the
illustrations in these Operating Instructions.
Carefully observe copyright laws.

• Recording of pre-recorded tapes or discs or other published or broadcast material for
purposes other than your own private use may infringe copyright laws. Even for the purpose
of private use, recording of certain material may be restricted.

Information for Your Safety
WARNING:
To reduce the risk of fire, electric shock or product damage,

• Do not let water or other liquids drip or splash inside the unit.
• Do not expose accessories (battery pack, battery charger, AC adaptor, SD memory
card and etc.) to rain, moisture, dripping or splashing.

• Use only the recommended accessories.
• Do not remove covers.
• Do not repair this unit by yourself. Refer servicing to qualified service personnel.
The socket outlet shall be installed near the equipment and shall be easily
accessible.

∫ Product identification marking
Product

Location

Digital Camera

Bottom

Battery Charger

Bottom

2 SQT0728 (ENG)

DMC-FT30EB-SQT0728_mst.book 3 ページ

2014年11月25日 火曜日 午前9時12分

(ENG) SQT0728

3

DMC-FT30EB-SQT0728_mst.book 4 ページ

2014年11月25日 火曜日 午前9時12分

∫ About the battery pack
CAUTION

• Danger of explosion if battery is incorrectly replaced. Replace only with the type
recommended by the manufacturer.

• When disposing of the batteries, please contact your local authorities or dealer and ask
for the correct method of disposal.

• Do not heat or expose to flame.
• Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with
doors and windows closed.

Warning
Risk of fire, explosion and burns. Do not disassemble, heat above 60 xC or
incinerate.

∫ About the battery charger
CAUTION!
To reduce the risk of fire, electric shock or product damage,

• Do not install or place this unit in a bookcase, built-in cabinet or in another
confined space. Ensure this unit is well ventilated.

• The battery charger is in the standby condition when the AC power supply cord is connected.
The primary circuit is always “live” as long as the power cord is connected to an electrical
outlet.

4 SQT0728 (ENG)

DMC-FT30EB-SQT0728_mst.book 5 ページ

2014年11月25日 火曜日 午前9時12分

∫ Cautions for Use
• Do not use any other USB connection cables except the supplied one or a genuine
Panasonic USB connection cable (DMW-USBC1: optional).

• Always use a genuine Panasonic AV cable (DMW-AVC1: optional).
Keep this unit as far away as possible from electromagnetic equipment (such as
microwave ovens, TVs, video games etc.).

• If you use this unit on top of or near a TV, the pictures and/or sound on this unit may be
disrupted by electromagnetic wave radiation.

• Do not use this unit near cell phones because doing so may result in noise adversely
affecting the pictures and/or sound.

• Recorded data may be damaged, or pictures may be distorted, by strong magnetic fields
created by speakers or large motors.

• Electromagnetic wave radiation may adversely affect this unit, disturbing the pictures and/or
sound.

• If this unit is adversely affected by electromagnetic equipment and stops functioning properly,
turn this unit off and remove the battery or disconnect AC adaptor (DMW-AC5E: optional).
Then reinsert the battery or reconnect AC adaptor and turn this unit on.

Do not use this unit near radio transmitters or high-voltage lines.

• If you record near radio transmitters or high-voltage lines, the recorded pictures and/or sound
may be adversely affected.

(ENG) SQT0728

5

DMC-FT30EB-SQT0728_mst.book 6 ページ

2014年11月25日 火曜日 午前9時12分

Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying
documents mean that used electrical and electronic products and
batteries must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and
used batteries, please take them to applicable collection points in
accordance with your national legislation.
By disposing of them correctly, you will help to save valuable
resources and prevent any potential negative effects on human
health and the environment.
For more information about collection and recycling, please contact
your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in
accordance with national legislation.
Note for the battery symbol (bottom symbol):
This symbol might be used in combination with a chemical symbol.
In this case it complies with the requirement set by the Directive for
the chemical involved.

6 SQT0728 (ENG)

DMC-FT30EB-SQT0728_mst.book 7 ページ

2014年11月25日 火曜日 午前9時12分

Contents
Information for Your Safety......................................................................................... 2
Before Use .................................................................................................................... 8
Accessories .................................................................................................................. 9
(Important) About the Waterproof/Dustproof and Anti-shock Performance
of the Camera ............................................................................................................. 11
Names and Functions of Main Parts ........................................................................ 17
Charging the Battery.................................................................................................. 18
Inserting and Removing the Card (optional)/the Battery ....................................... 19
Sequence of operations ............................................................................................ 20
Reading the Operating Instructions (PDF format) .................................................. 22
Installing supplied software...................................................................................... 23
Specifications............................................................................................................. 24

(ENG) SQT0728

7

DMC-FT30EB-SQT0728_mst.book 8 ページ

2014年11月25日 火曜日 午前9時12分

Before Use
Please be sure to read “(Important) About the Waterproof/Dustproof and Anti-shock
Performance of the Camera” (P11) before using this unit underwater to prevent the
unit from being mishandled, which may cause water to seep in.

• Do not apply strong shock or vibration by dropping or knocking the camera. Also, do
not apply strong pressure to the camera.
– Waterproof performance may be impaired.
– Lens or LCD monitor may be damaged.
– It may cause malfunction in the performance or the function.

∫ When inner side of the lens is fogged (condensation)
It is not a malfunction or failure of the camera. It may be
caused by the environment in which the camera is used.
What to do when inner side of the lens is fogged

• Turn off the power and open the side door in a place with constant
ambient temperature, away from high temperatures, humidity,
sand and dust. The fog will disappear naturally in 10 minutes to
2 hours with the side door open when the temperature of the
camera gets close to the ambient temperature.
• Contact Panasonic if the fogging does not disappear.

Conditions in which inner side of the lens may be fogged
Condensation may occur and the inner side of the lens may be fogged when the
camera is used in areas that undergo a significant change in temperature or in high
humidity, such as the following:

• When the camera is used underwater suddenly after being on a hot beach etc.
• When the camera is moved to a warm area from a cold area, such as at a ski resort or
at high altitude

• When the side door is opened in a high-humidity environment

8 SQT0728 (ENG)

DMC-FT30EB-SQT0728_mst.book 9 ページ

2014年11月25日 火曜日 午前9時12分

Accessories
Check that all the accessories are supplied before using the camera.
Product numbers correct as of January 2015. These may be subject to change.
1

3
4
5

Battery Pack
(Indicated as battery pack or battery in
the text)
Charge the battery before use.
Battery Charger
(Indicated as battery charger or
charger in the text)
AC Mains Lead
USB Connection Cable
CD-ROM

6

Install on your PC before use.
Hand Strap

2

1

2

DMW-BCK7E

3

DE-A92A

4

• Software
• Operating Instructions for advanced
features

K2CT3YY00034

5

K1HY08YY0031

6

• Supplied accessories are not waterproof.
• SD Memory Card, SDHC Memory Card and

SDXC Memory Card are indicated as card in
the text.
VFC4297
SFM0076
• The card is optional.
You can record or play back pictures on the
built-in memory when you are not using a card.
• Consult the dealer or Panasonic if you lose the supplied accessories. (You can purchase the
accessories separately.)

(ENG) SQT0728

9

DMC-FT30EB-SQT0728_mst.book 10 ページ

2014年11月25日 火曜日 午前9時12分

Sales and Support Information
Customer Communications Centre

• For customers within the UK: 0844 844 3899
• For customers within Ireland: 01 289 8333
• Monday–Friday 9:00 am – 5:00 pm, (Excluding public holidays).
• For further support on your product, please visit our website:
www.panasonic.co.uk

Direct Sales at Panasonic UK

• Order accessory and consumable items for your product with ease and confidence by
phoning our Customer Communications Centre Monday–Friday 9:00 am – 5:00 pm,
(Excluding public holidays).

• Or go on line through our Internet Accessory ordering application at www.pas-europe.com.
• Most major credit and debit cards accepted.
• All enquiries transactions and distribution facilities are provided directly by Panasonic UK.
• It couldn’t be simpler!
• Also available through our Internet is direct shopping for a wide range of finished products.
Take a browse on our website for further details.

∫ Optional Accessories
Battery Pack

DMW-BCK7

AC Adaptor¢

DMW-AC5

DC Coupler¢

DMW-DCC10

USB Connection Cable

DMW-USBC1

AV Cable

DMW-AVC1

¢

The AC Adaptor (optional) can only be used with the designated Panasonic DC Coupler
(optional). The AC adaptor (optional) cannot be used by itself.

Some optional accessories may not be available in some countries.

10 SQT0728 (ENG)

DMC-FT30EB-SQT0728_mst.book 11 ページ

2014年11月25日 火曜日 午前9時12分

(Important) About the Waterproof/
Dustproof and Anti-shock Performance of
the Camera
Waterproof/Dustproof Performance
This camera’s waterproof/dustproof rating complies with the “IPX8” and
“IP6X” ratings. Provided the care and maintenance guidelines described in
this document are strictly followed, this camera can operate underwater, to a
depth not exceeding 8 m (26 feet) for a time not exceeding 60 minutes. (¢1)
Anti-shock Performance
This camera also complies with “MIL-STD 810F Method 516.5-Shock”. The
camera has cleared a drop test from a height of 1.5 m (5 feet) onto 3 cm
(0.1 feet) thick plywood. In most cases this camera should not sustain any
damage if dropped from a height not exceeding 1.5 m (5 feet). (¢2)
This does not guarantee no destruction, no malfunction, or waterproofing in all
conditions.
¢1 This means that the camera can be used underwater for specified time in specified
pressure in accordance with the handling method established by Panasonic.
¢2 “MIL-STD 810F Method 516.5-Shock” is the test method standard of the U.S. Defense
Department, which specifies performing drop tests from a height of 122 cm (4 feet), at
26 orientations (8 corners, 12 ridges, 6 faces) using 5 sets of devices, and passing the
26 orientation drops within 5 devices. (If failure occurs during the test, a new set is used to
pass the drop orientation test within a total of 5 devices)
Panasonic’s test method is based on the above “MIL-STD 810F Method 516.5-Shock”.
However, the drop height was changed from 122 cm (4 feet) to 150 cm (5 feet) dropping
onto 3 cm (0.1 feet) thick plyboard. This drop test was passed.
(Disregarding appearance change such as loss of paint or distortion of the part where
drop impact is applied.)

(ENG) SQT0728

11

DMC-FT30EB-SQT0728_mst.book 12 ページ

2014年11月25日 火曜日 午前9時12分

∫ Handling of the camera
• Waterproofing is not guaranteed if the unit is subject to an impact as a result of being hit or
dropped etc. If an impact to the camera occurs, it should be inspected (subject to a fee) by
Panasonic to verify that the waterproofing is still effective.

• When the camera is splashed with detergent, soap, hot spring, bath additive, sun oil, sun
screen, chemical, etc., wipe it off immediately.

• Waterproof function of the camera is for sea water and fresh water only.
• Any malfunction caused by customer misuse, or mishandling will not be covered by the
warranty.

• The inside of this unit is not waterproof. Water leakage will cause malfunction.
• Supplied accessories are not waterproof.
• Card and battery are not waterproof. Do not handle with a wet hand. Also, do not insert wet
card or battery into the camera.

• Do not leave the camera for a long period of time in places where the temperature is very low

(such as at ski resorts or high altitudes) or where the temperature may exceed 40 ºC (104 oF)
(such as inside cars in strong sunlight, close to a heater, on boats, or on the beach).
(Waterproof performance may become degraded.)

∫ About the [Precautions] demonstration display ([Requirements for
Underwater use])
• [Precautions] is displayed when the power is turned on for the first time after purchase, with
the side door completely closed.

• Please check beforehand to maintain the waterproof performance.

1

Press 2 to select [Yes], and press [MENU/SET].

2

Press 2/1 to select the picture.

• It will automatically skip to the clock setting screen if [No] is selected before it starts.
2:

Return to the previous screen

1:

View the next screen

• It can be forcefully ended by pressing [MENU/SET].
• When it is forcefully ended while checking by turning the unit off or pressing [MENU/
SET], [Precautions] is displayed every time the power is turned on.

3

After the final screen (12/12), press [MENU/SET] to finish.

• When [MENU/SET] is pressed after the final screen (12/12), [Precautions] is not
displayed from the next time the power is turned on.

• This can also be viewed from [Precautions] in the [Setup] menu.

12 SQT0728 (ENG)

DMC-FT30EB-SQT0728_mst.book 13 ページ

2014年11月25日 火曜日 午前9時12分

Check before using underwater
Always wipe the rubber seal on the side door and the area where rubber seal
sits with a dry, lint-free cloth.

1

Check that there are no foreign objects on the inner side of the side door.

• If there is any foreign object, such as lint, hair, sand, etc., on the surrounding area,
water will leak within a few seconds causing malfunction.

• Wipe it off with a dry soft cloth if there is any liquid.

It may cause water leaks and malfunction if you use the camera with liquid adhered.

• If foreign objects are present, wipe them off with a dry, lint-free cloth.
• Be extremely careful to remove the small sand etc. that may adhere to the sides and
corners of the rubber seal.

2

Check for cracks and deformation of the rubber seal on the side door.

• The integrity of the rubber seals may decrease after about 1 year, with use and age. To

avoid permanently damaging the camera the seals should be replaced once each year.
Please contact Panasonic for related costs and other information.

3

Close the side door securely.
ロヰヤレ

ロヰヤレ
ロヰヤレ

A [LOCK] switch (grey part)
B Red part
C Released state
D Locked state
• Lock the [LOCK] switch securely until
the red part is no longer visible.
• To prevent water intrusion, be careful
not to catch foreign objects such as
liquids, sand, hair, dust, or the strap
cord.

Do not open or close the side door in places with sand and dust, close to water,
or with wet hands. Sand or dust adhering may cause water leaks.

(ENG) SQT0728

13

DMC-FT30EB-SQT0728_mst.book 14 ページ

2014年11月25日 火曜日 午前9時12分

Using the camera underwater
• Use the camera underwater to 8 m (26 feet) with the water temperature between 0 oC and
40 oC (32 oF and 104 oF).

• Do not use for scuba diving (Aqualung).
• Do not use the camera at a depth of over 8 m (26 feet).
• Do not use it in the hot water over 40 oC (104 oF) (in the bath or hot spring).
• Do not use the camera underwater longer than 60 minutes continuously.
• Do not open or close the side door underwater.
• Do not apply shock to the camera underwater. (Waterproof performance may not be
maintained, and there is a chance of water leak.)

• Do not dive into the water holding the camera. Do not use the camera in a location where the

water will splash strongly, such as rapid flow or waterfall. (Strong water pressure may be
applied, and it may cause malfunction.)
• The camera will sink in the water. Take care not to drop the camera and lose it underwater by
securely placing the strap around your wrist or similar measure.

14 SQT0728 (ENG)

DMC-FT30EB-SQT0728_mst.book 15 ページ

2014年11月25日 火曜日 午前9時12分

Caring of the camera after using it underwater
Do not open or close the side door until the sand and dust is removed by
rinsing the camera with water.
Make sure to clean the camera after using it.

• Thoroughly wipe off any water droplets, sand, and saline matter on your hands, body, hair,
etc.

• It is recommended to clean the camera indoors, avoiding places where water spray or
sand may fall.

After using it underwater, always clean the camera rather than leaving it in a
dirty state.

• Leaving the camera with foreign objects or saline matter on it may cause damage,

discolouration, corrosion, unusual odour, or deterioration of the waterproof performance.

1

Rinse with water with the side door closed.

• After use at the seaside or underwater, soak the unit in
•

•

fresh water pooled in a shallow container for
10 minutes or less.
If the zoom button or camera [ON/OFF] button do not
press smoothly, it may be caused by an adhesion of
foreign objects. Using in such a state may cause
malfunctions, such as locking up, so wash off any
foreign objects by shaking the camera in fresh water.
Bubbles may come out of the drainage hole when you
immerse the camera in water, but this is not a
malfunction.

(ENG) SQT0728

15

DMC-FT30EB-SQT0728_mst.book 16 ページ

2

2014年11月25日 火曜日 午前9時12分

Drain water by holding the camera upside-down A and the right way up B
and shaking it lightly a few times.

• After using the camera at the beach or in water, or after washing it, water may remain
around the speaker and microphone for a while and may cause a drop in volume or
sound distortion.

• Make sure to put your hand through the strap to prevent the camera from falling.

3

Wipe off water drops on the camera with a
dry soft cloth and dry the camera in a
shaded area which is well ventilated.

• Dry the camera by standing it on a dry cloth.

•
•

4

This unit incorporates drain design, draining
water in gaps in the camera [ON/OFF] button
and zoom button etc.
Do not dry the camera with hot air from dryer
or similar. Waterproof performance will
deteriorate due to deformation.
Do not use chemicals such as benzine, thinner, alcohol or cleanser, soap or
detergents.

Confirm that there are no water droplets, open the side door, and wipe off
any water droplets or sand left inside using a soft dry cloth.

• Water droplets may adhere to the card or battery when the side door is opened without
thoroughly drying. Also, water may accumulate in the gap around the card/battery slot
or the terminal connector. Be sure to wipe any water off with a soft dry cloth.

• The water droplets may seep into the camera when the side door is closed while it is
still wet, causing condensation or failure.

16 SQT0728 (ENG)

DMC-FT30EB-SQT0728_mst.book 17 ページ

2014年11月25日 火曜日 午前9時12分

Names and Functions of Main Parts
8

1 2 3 45 6 7

9

10 11

12
13
14

17
18
19
20

Flash
Motion picture button
Shutter button
Camera [ON/OFF] button
Microphone
Self-timer indicator/
AF Assist Lamp/
LED light
Lens
LCD monitor
[MODE] button
Zoom button
Strap eyelet

21

• Be careful not to cover the speaker

Tripod mount

• A tripod with a screw length of 5.5 mm
(0.22 inch) or more may damage this
unit if attached.

• Be sure to attach the strap when

Release lever
[LOCK] switch
Side door
[(] (Playback) button
[Q.MENU] button/[
Cancel) button

[DISP.] button
[MENU/SET] button
Cursor buttons
Speaker

with your finger. Doing so may make
sound difficult to hear.

using the camera to ensure that you
will not drop it.

12
13
14
15
16

ヤモンュ

7
8
9
10
11

23
24

19 18 17 16 15

ャモヵヵユンヺ

1
2
3
4
5
6

21

モヷチヰヶヵバチュリヨリヵモロ

20

22

22
23
24

[AV OUT/DIGITAL] socket
Card slot
Battery slot

• When using an AC adaptor, ensure

•
] (Delete/

•

that the Panasonic DC coupler
(DMW-DCC10: optional) and AC
adaptor (DMW-AC5E: optional) are
used.
Always use a genuine Panasonic AC
adaptor (DMW-AC5E: optional).
When using an AC adaptor, use the
AC Mains Lead supplied with the AC
adaptor.

(ENG) SQT0728

17

DMC-FT30EB-SQT0728_mst.book 18 ページ

2014年11月25日 火曜日 午前9時12分

Charging the Battery
Use the dedicated charger and battery.

• The battery is not charged when the camera is shipped. Charge the battery before use.
• Charge the battery with the charger indoors [10 oC to 30 oC (50 oF to 86 oF)].
Attach the battery paying attention to the
direction of the battery.

Connect the AC Mains Lead.
• The [CHARGE] indicator A lights up and charging
begins.

∫ About the [CHARGE] indicator
On:
Off:

Charging.
Charging has completed. (Charging time: Approx. 120 min)

∫ About batteries that you can use with this unit
The battery that can be used with this unit is DMW-BCK7E.

18 SQT0728 (ENG)

DMC-FT30EB-SQT0728_mst.book 19 ページ

2014年11月25日 火曜日 午前9時12分

Inserting and Removing the Card
(optional)/the Battery
• Check that this unit is turned off.
• Confirm that there is no foreign object.
• We recommend using a Panasonic card.

ロヰヤレ

1:Slide the [LOCK] switch A, and
release the lock.
2:Slide the release lever B and
open the side door.
• Always use genuine Panasonic batteries
(DMW-BCK7E).

• If you use other batteries, we cannot

guarantee the quality of this product.

Battery: Being careful about the
battery orientation, insert all the
way until you hear a locking sound
and then check that it is locked by
lever C. Pull the lever C in the
direction of the arrow to remove
the battery.
Card: Push it securely all the way
until you hear a “click” while being
careful about the direction in
which you insert it. To remove the card, push the card until it
clicks, then pull the card out upright.
Close the side door until it clicks,
and then lock the [LOCK] switch
by sliding it toward [2].
• Confirm that the red part on the [LOCK]

ロヰヤレ

D: Do not touch the connection terminals of the card.

switch is not showing.

Note

• Keep the Memory Card out of reach of children to
prevent swallowing.

(ENG) SQT0728

19

DMC-FT30EB-SQT0728_mst.book 20 ページ

2014年11月25日 火曜日 午前9時12分

Sequence of operations
Press camera [ON/OFF] button.
• The clock is not set when the camera is
shipped. Set the date and time before
using the camera.

Press the shutter button halfway to
focus and then press it fully to take
the picture.
∫ Selecting the Recording Mode
Press [MODE] to select the Recording Mode.
: Take pictures with automatic settings.
: Take pictures with your own settings.
: Record while checking the image effect.
: This mode is optimal for taking pictures of sporting events, etc.
: This mode is optimal for taking pictures that show the snow as white as possible at
a ski resort or a snow-covered mountain.
: This mode is optimal for taking pictures to 3 m (10 feet) underwater and at the
beach.
: This mode is optimal for taking pictures at depths of 3 m (10 feet) to 8 m (26 feet).
: This mode allows you to take panorama pictures.
: Take pictures according to scene.

20 SQT0728 (ENG)

DMC-FT30EB-SQT0728_mst.book 21 ページ

2014年11月25日 火曜日 午前9時12分

∫ Recording Motion Pictures
Start recording by pressing the motion picture button.

• Stop the recording by pressing the motion picture button again.
• Maximum time to record motion pictures continuously is 29 minutes 59 seconds.
The maximum available recording time continuously is displayed on the screen.

∫ Setting the Menu
Press [MENU/SET] to display the menu screen to change the recording function,
camera settings, and other settings.

∫ Playing Back Pictures
Press [(].

• Press 2/1 to select the picture.
∫ Deleting Pictures
Select the picture, and then press [

].

• Confirmation screen is displayed. Picture is deleted by selecting [Yes].
∫ About the [LED Light] ([Setup])
If you set to [
], and press and hold down 1 (‰) on the
recording standby screen, the LED light will come on for
60 seconds.

(ENG) SQT0728

21

DMC-FT30EB-SQT0728_mst.book 22 ページ

2014年11月25日 火曜日 午前9時12分

Reading the Operating Instructions
(PDF format)
More detailed instructions on the operation of this camera are contained in
“Operating Instructions for advanced features (PDF format)” in the supplied
CD-ROM.

∫ For Windows
Turn the PC on and insert the CD-ROM containing the Operating
Instructions (supplied).
• If the automatic playback screen is displayed, you can display the menu by selecting
and executing [Launcher.exe].

• In Windows 8/Windows 8.1, you can display the menu by clicking a message that is
•

displayed after inserting the CD-ROM and then selecting and executing
[Launcher.exe].
You can also display the menu by double-clicking [SFMXXXX] in [Computer] (XXXX
differs depending on the model).

Click the [Operating Instructions].
• The list of Operating Instructions (PDF format) will be displayed.
Click the language of the Operating Instructions you want to
open.
• The “Operating Instructions for advanced features (PDF format)” will open.
You can save the “Operating Instructions for advanced features” on the PC.

• You will need Adobe Reader to browse or print the “Operating Instructions for advanced
features (PDF format)”.
You can download and install a version of Adobe Reader that you can use with your OS from
the following website. (As of January 2015)
http://www.adobe.com/products/acrobat/readstep2.html

22 SQT0728 (ENG)

DMC-FT30EB-SQT0728_mst.book 23 ページ

2014年11月25日 火曜日 午前9時12分

Installing supplied software
• The supplied CD-ROM includes the following software.
– PHOTOfunSTUDIO 9.0 SE (Windows Vista/Windows 7/Windows 8/Windows 8.1)
– LoiLoScope 30 day full trial version (Windows Vista/Windows 7/Windows 8/Windows 8.1)
(This will only install a shortcut to the trial version download site.)

• Before inserting the CD-ROM, close all running applications.

Check the environment of your PC.
• For details about information such as the operating environment or operating
method, refer to the “Operating Instructions for advanced features (PDF format)” or
the operating instructions for the respective software programmes.

Insert the CD-ROM with the supplied software.
• If the automatic playback screen is displayed, you can display the menu by selecting
and executing [Launcher.exe].

• In Windows 8/Windows 8.1, you can display the menu by clicking a message that is
•

displayed after inserting the CD-ROM and then selecting and executing
[Launcher.exe].
You can also display the menu by double-clicking [SFMXXXX] in [Computer] (XXXX
differs depending on the model).

Click on the [Applications] on the install menu.
Click on the [Recommended Installation].
• Proceed with installation according to messages appearing on the screen.
Note

• The software compatible with your PC will be installed.
• “PHOTOfunSTUDIO” and “LoiLoScope” are not compatible with Mac.

(ENG) SQT0728

23

DMC-FT30EB-SQT0728_mst.book 24 ページ

2014年11月25日 火曜日 午前9時12分

Specifications
Specifications are subject to change without notice.
Digital Camera:
Information for your safety
Power Source:

DC 5.1 V

Power Consumption: 1.0 W (When recording)
0.6 W (When playing back)
Camera effective
pixels

16,100,000 pixels

Image sensor

1/2.33q CCD, total pixel number 16,600,000 pixels, Primary
colour filter

Lens

Optical 4k zoom, fl4.5 mm to 18 mm (35 mm film camera
equivalent: 25 mm to 100 mm)/F3.9 (Wide) to F5.7 (Tele)

Image stabiliser

Optical method

Focus range

Normal

50 cm (1.6 feet) (Wide)/1 m (3.3 feet)
(Tele) to ¶

Macro/
Intelligent auto/
Motion picture

5 cm (0.16 feet) (Wide)/1 m (3.3 feet)
(Tele) to ¶

Scene Mode

There may be differences in the above
settings.

Shutter system

Electronic shutteriMechanical shutter

Minimum
Illumination

Approx. 14 lx (when i-low light is used, the shutter speed is
1/25th of a second)

Shutter speed

8 seconds to 1/1300th of a second
[Starry Sky] Mode: 15 seconds, 30 seconds, 60 seconds

Exposure (AE)

Auto (Programme AE)

Metering mode

Multiple

LCD monitor

2.7q TFT LCD (4:3)
(Approx. 230,000 dots) (field of view ratio about 100%)

24 SQT0728 (ENG)

DMC-FT30EB-SQT0728_mst.book 25 ページ

2014年11月25日 火曜日 午前9時12分

Microphone

Monaural

Speaker

Monaural

Recording media

Built-in Memory (Approx. 220 MB)/SD Memory Card/
SDHC Memory Card/SDXC Memory Card

Recording file format
Still Picture

JPEG (based on “Design rule for Camera File system”,
based on “Exif 2.3” standard)/DPOF corresponding

Motion pictures

MP4

Audio compression
format

AAC

Interface
Digital

“USB 2.0” (High Speed)
¢

Data from the PC can not be written to the camera using the
USB connection cable.

Analogue video

NTSC/PAL Composite (Switched by menu)

Audio

Audio line output (monaural)

Terminal
[AV OUT/DIGITAL]

Dedicated jack (8 pin)

Dimensions
(excluding the
projecting parts)

Approx. 103.7 mm (W)k58.3 mm (H)k19.7 mm (D)
[4.08q(W)k2.3q(H)k0.77q(D)]

Mass

Approx. 144 g/0.317 lb (with card and battery)
Approx. 125 g/0.275 lb (excluding card and battery)

(ENG) SQT0728

25

DMC-FT30EB-SQT0728_mst.book 26 ページ

2014年11月25日 火曜日 午前9時12分

Operating
temperature

j10 oC¢ to 40 oC (14 oF¢ to 104 oF)

Operating humidity

10%RH to 80%RH

Waterproof
performance

Equivalent to IEC 60529 “IPX8”.
[Usable for 60 minutes in 8 m (26 feet) water depth]

Crash resistance
perfomance

The test method of the camera is in compliance with
“MIL-STD 810F Method 516.5-Shock”¢.

¢

The performance of the battery (number of recordable
pictures/operating time) may decrease temporarily when
using in a temperature between j10 oC and 0 oC (14 oF and
32 oF) (cold places such as ski resorts or places at high
altitude).

“MIL-STD 810F Method 516.5-Shock” is the test method
standard of the U.S. Defense Department, which specifies
performing drop tests from a height of 122 cm (4 feet), at 26
orientations (8 corners, 12 ridges, 6 faces) using 5 sets of
devices, and passing the 26 orientation drops within 5
devices.
(If failure occurs during the test, a new set is used to pass the
drop orientation test within a total of 5 devices)
• Panasonic’s test method is based on the above “MIL-STD 810F
Method 516.5-Shock”. However, the drop height was changed
from 122 cm (4 feet) to 150 cm (5 feet) dropping onto 3 cm
(0.1 feet) thick plyboard. This drop test was passed.
(Disregarding appearance change such as loss of paint or
distortion of the part where drop impact is applied.)
¢

There is no guarantee of not breaking or malfunctioning
under all conditions.
Dustproof
performance

26 SQT0728 (ENG)

Equivalent to IEC 60529 “IP6X”.

DMC-FT30EB-SQT0728_mst.book 27 ページ

2014年11月25日 火曜日 午前9時12分

Battery Charger (Panasonic DE-A92A):
Information for your safety
Input:

AC

110 V to 240 V, 50/60 Hz, 0.2 A

Output:

DC

4.2 V, 0.43 A

Operating
temperature:

0 oC¢ to 40 oC (32 oF¢ to 104 oF)
¢

The battery cannot be recharged in a temperature less than
0 oC (32 oF). (The [CHARGE] indicator blinks when the
battery cannot be recharged.)

Battery Pack (lithium-ion) (Panasonic DMW-BCK7E):
Information for your safety
Voltage/capacity:

3.6 V/680 mAh

(ENG) SQT0728

27

DMC-FT30EB-SQT0728_mst.book 20 ページ

2014年11月25日 火曜日 午前9時12分

• SDXC Logo is a trademark of SD-3C, LLC.
• QuickTime and the QuickTime logo are trademarks or

registered trademarks of Apple Inc., used under license
therefrom.
• Mac and Mac OS are trademarks of Apple Inc., registered in
the U.S. and other countries.
• Windows and Windows Vista are either registered trademarks
or trademarks of Microsoft Corporation in the United States
and/or other countries.
• This product uses “DynaFont” from DynaComware Corporation. DynaFont is a
registered trademark of DynaComware Taiwan Inc.
• Other names of systems and products mentioned in these instructions are usually
the registered trademarks or trademarks of the manufacturers who developed the
system or product concerned.
This product is licensed under the AVC patent portfolio license for the personal and
non-commercial use of a consumer to (i) encode video in compliance with the AVC
Standard (“AVC Video”) and/or (ii) decode AVC Video that was encoded by a
consumer engaged in a personal and non-commercial activity and/or was obtained
from a video provider licensed to provide AVC Video. No license is granted or shall be
implied for any other use. Additional information may be obtained from MPEG LA,
LLC. See http://www.mpegla.com .

Manufactured by:

Panasonic Corporation
Kadoma, Osaka, Japan
Importer for Europe: Panasonic Marketing Europe GmbH
Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg,
Germany

Panasonic Corporation
Web Site: http://panasonic.net

 Panasonic Corporation 2015

EU



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39
Modify Date                     : 2015:01:16 13:40:40+09:00
Create Date                     : 2015:01:16 13:40:40+09:00
Metadata Date                   : 2015:01:16 13:40:40+09:00
Format                          : application/pdf
Document ID                     : uuid:85f5a718-261d-4e7c-b7e2-d7a6f5097f90
Instance ID                     : uuid:adaa95bf-3da0-43ea-adb9-30baea61e6f0
Page Count                      : 28
EXIF Metadata provided by EXIF.tools

Navigation menu