Panasonic WLAN-DONGLE Wireless LAN Dongle User Manual 2AO5HWLAN DONGLE 20180720

Panasonic Corporation Wireless LAN Dongle 2AO5HWLAN DONGLE 20180720

2AO5HWLAN-DONGLE_User Manual_20180720

购买年月日
型号
DV0PM20105
销售商店名
电 话（ ） －
English
Operation Manual
Wireless LAN Dongle
Part
No.
D
V
０ＰＭ２０１０５
■登记卡（为了今后咨询、修理时的需要, 请填写登记卡）
●
Thank you very much for purchasing the Panasonic product.
●
Carefully read this operation manual prior to use the product
correctly.
●
Always read “Cautions for Safety” prior to use.
●
Store this operation manual carefully.
●
This equipment is used only for the industrial purpose.
You cannot use in ordinary homes.
Read operation manual for setup support software down-
loaded from our website prior to use.
【Panasonic Corporation Motor Business Unit Website】
https://industrial.panasonic.com/ww/products/motors-
compressors/fa-motors
Hand over this operation manual to the end-user
.
－ C28
－
IME98
Z1016-0
Caution
(1) Republication of any part or all of this document
without permission is prohibited.
(2) Contents of this document are subject to change
without notice.
－ E3
－
English
Cautions for
safety Be sure to comply with.
■ Contents The
following
section explains
the items that y
ou
page
Cautions for safety
.....................................................
E3
Requests to use Wireless LAN Dongle .................... E7
Application
........................................................................
E10
Listed contents on the
website..........................................
E10
1. Introduction............................................................E11
When you unpacked
.........................................................
E11
shall comply with to
prevent dangers
to
humans and
damage
to
properties.
■ This
section explains
the level of
dangers and
damages
by the
classification,
which may
occur
when the wrong
usage
is carried
out.
The content that
Name of parts
...................................................................
E12
Outline...............................................................................
E13
2. Connection
mode .................................................
E15
3.
Connection............................................................
E17
4. Setting
...................................................................
E18
5. General
Specifications
.........................................
E23
DANGER
WARNING
“it
may result in
death
or
serious
injury.”
The content that
“it
may lead to
death
or
serious
injury.”
6. When you are in
trouble.......................................
E25
Guarantee..................................................................
E27
Precautions for use
..................................................
E28
Federal Communication Commission Interference
Statement
...................................................................
E30
After-sales
service....................................................
E32
■ Following
pictographic
symbol
explains
the
content
that you shall comply with.
The content that you shall not
perform.
The
content
that you must
execute.
－ E5
－
Do not use the product
in an airplane.
Otherwise,
it
may
cause problems to
the
safety
of
aircraf
t
operation.
Do not use the product
in a hospital or a place
where an electro-medi-
cal apparatus is placed.
The electric
wave
from the
product
may
have
an
effect
on the
electro-med
-
ical
apparatus and
cause accident due
to the
abnormal
operation.
Do not use the product
when there is a person
nearby who has a car-
diac pacemaker.
Otherwise,
the
electric wave
may
adversely
affect
the
operation
of
pace
-
maker.
Do not use near the
automatic control
equipment such as an
automatic
door or a
fire
alarm
box.
The electric
wave
from the
product
may
have
an
effect
on the
automatic
control
equipment
and cause accident
due to the
abnor
-
mal
operation.
English
Cautions for
safety Be sure to comply with.
DANGER
W
ARNING
Do not use the prod-
uct in the place where
water may splash over,
in the corrosive atmo-
sphere
or
flammable
gas atmosphere or near
the combustible ob-
jects.
Otherwise,
it
may
cause
fire,
electric
shock, malfunction
or
breakage.
Do not install the prod-
uct near the heating ele-
ment such as a heater
or a large fixed
wire-
wound resistor.
Otherwise,
it
may
cause
fire or
mal
-
function.
Install the product in
the place with few dust
and water or oil is not
splashed over.
If the
installation
place
is not
cor
-
rect, it may
cause
electric
shock,
fire,
malfunction or
breakage.
Always check the safety
after the occurrence of
earthquakes.
Otherwise,
it
may
cause electric
shock,
injury or
fire.
Ensure to install and set
the equipment so that
fire,
accident causing
injury or death does not
occur in earthquakes.
Otherwise,
it
may
cause electric
shock,
injury or
fire.
－ E7
－
Do not approach the
equipment because the
equipment may oper-
ate suddenly or the
movement may change
rapidly by changing the
setting.
Otherwise,
it
may
cause injuries.
The person who has a
cardiac pacemaker
shall keep the distance
22 cm or more off the
product.
Otherwise,
the
electric wave
may
adversely
affect
the
operation
of
pace
-
maker.
To
discard
this
product, process as
the
industrial
waste.
English
Cautions for
safety Be sure to comply with.
Requests
to use
Wireless
LAN
Dongle
◇ Frequency band for use
The product
uses
the
frequency
band of 2.4 GHz
band, and
also other
wireless equipment
may use the
same
frequency
.
To
prevent
the radio wave int
er
f
erenc
e
with other
wir
eles
s
equipment, please
use paying
attention
to the
following t
erms.
Cautions to use Wireless LAN
equipment
In the
frequency
band for use of this
equipment,
the
in-plant
radio
stations
for the mobile identification which is
used
on
the
manufacturing
lines in
factories
(Radio station that
needs
the
license), specified
low power radio
stations
(Radio
station
that
needs
no
license)
and
amateur
radio
stations
(Radio
station that
needs
the
license)
are
operated
in addition to
the
industrial/scientific/medical equipment
like
microwave
ovens.
1.
Check
that the in-plant radio
stations
for the
mobile
i
d
en
ti
fi
cati
on,
specified
l
o
w power radio
stations
a
nd
amateur
radio
stations
are not
operated
in the vicinity
prior to use this
equipment.
2. If the
case
of harmful radio wave
interference
occurred
from this
equipment
to the in-plant radio
stations
for
the
mobile
ident
if
ic
at
ion,
immediately change
the
loc
at
ion
or stop the use of electric wave and then
contact
to
our
company (Page
E30) to
have a
talk about the
action
to the
interference avoidance
(e.g. the
installation
of
partitions).
3. If you
have
any
problem,
for
example;
when the
case
of harmful radio wave
interference occurred
from
this
equipment
to the in-plant radio
stations
for the
mobile
identification or the
amateur
radio
stations, please
c
ont
ac
t
to our
company (Page E30).
－ E9
－
English
Requests
to use
Wireless
LAN
Dongle (continued)
◇
Equipment qualification
The product
needs
no
license
of radio
stations because
it
has
been approved
for the certification of
conformance to
technical standards
in
accordance
with the Radio Act. How-
ever, it is prohibited to implement the following acts to
the
product by the Radio Act.
・To
disassemble
or
remodel,
・To
erase
the
nameplate attached
to the side of
product.
◇ Usage restrictions
Please
note that there are
following
restrictions
to use t
he
product.
When
those restrictions
are not complied, we deny any
li
-
ability for the incidental loss and
damage raised
by the
use
of the product or the
unusable product.
・Use the product
as
the
wireless
LAN
equipment.
・The product can be
used
only in the
operational countries
listed on our
website.
・The product is
designed
to be able to
operate
in the
coun
-
try where the legal
regulation standard
is different.
Set
the country code
corresponding
to the country to use
the
product
because
the
specified
country code has
been
set at
manufacturing. Please
set the code with great
care
because
it will be the violation of law
if
you set the
wrong
country
code.
・Do not connect to the wireless network which you
have no authority of utilization.
During
automatic search
in the
wireless
network
circum
-
stances,
a
wireless
network (SSID*) which you have
no
authority of utilization may be
indicated.
It may be
deemed
as an illegal access.
・Do not use the product where magnetic field/static
electrical charge/radio disturbance occurs.
When you use the product near the following
equipment,
the
communication
may break up or the
speed
may
be
slow.
・Microwave
oven
・Digital
cordless telephone
set
・Near the
equipment
that
uses
the electric wave of
2.4 GHz
band.
E
x
a
m
p
l
e
;
Equipment supporting
Bluetooth,
wireless
audio
apparatus
or
game machine.
Select
the
wireless
broad band router
(Access
point) of
802.11
n (2.4 GHz). Use the encryption
scheme
of “AES.”
・Transmitting and receiving data by electric wave may
be intercepted.
・To reduce the security risk of the interception of com-
munications or illegal access, set the password for the
access point and PIN code to set for the driver so as
to be complicated containing the alphanumeric char-
acters.
・You are required to set the country code.
Please
set with great care
because
it will be the violation
of law
if
you set the wrong country
code.
*
It
means
the
name
to identify the
specified network
by
wireless
LAN.
When
this SSID is
matched
by
mutual equipment,
t
he
communication
is
enabled.
－ E10
－
－ E11
－
English
Requests
to use
Wireless
LAN
Dongle (continued)
Application
The product is the dedicated device to our
servo driver.
(You cannot use it by connecting to PC.)
● For the servo driver you can connect
with the product, terminals that can be
connected by wireless, setup of the
product and using method, check on
our website;
https://industrial.panasonic.com/ww/products/
motors-compressors/fa-motors
1. Introduction
When you unpacked
・Is the product type correct by your
order?
・Is there any broken part during
transportation?
If you found any defective portion, please contact the
retailer that you purchased the product.
Type
confirmation
Nameplate
is
attached
to the side of
product.
When there is a
person nearby
who
uses
a
pacemaker or
you
cannot
use the
wireless
LAN,
please
use the
communi
-
cation cable (Use USB mini-B
connector
for the driver,
and
select
a proper
connector according
to
specification
of
the
Part No.
Serial Number
DV0PM20105
P16040001
R
201-160210
terminal.).
Example: P 1 6 0 4 0 0 0 1 CMIIT ID :
2016DJ2804
Panasonic Corporation
Listed contents on the
website
・List of servo drivers
possible
to
connect
・List of functions
available
in the
wireless communications
・
Operating procedure manual
of
the
setup support software
・
Countries
where you can use the
product.
・
Supported wireless authentication
standards
・
Specifications
of the
recommended terminals
・
Specifications
of the
recommended access points
Sequential number
Manufacturing month
Manufacturing year (Last two digits of the Christian year)
－ E12
－
－ E13
－
English
1. Introduction (continued)
Name of parts
Wireless LAN Dongle
Lamp
(Blue LED)
Connector
Outline
This product is the
wireless
LAN dongle which
enables the
wireless connection between
the servo driver and your
ter
-
minals (PC,
smartphones,
tablet type
terminals)
by
connect
-
ing to the servo driver. When you use the Windows OS
ap
-
plicable
setup support software
“PANATERM”
or the
iPhone
terminals and Android terminals
applicable setup support
software “Panasonic
Motor
Setup
App,” it is
required
to
con
-
nect your PC and servo driver with
cables,
but the
wireless
system
will
be
possible
by using this
product.
The lamp
shows
the
state
of product when it is
connected to
the servo
driver
.
● Lights on:
The
state
when the power is
supplied
to the product but it
is not
communicating
with the
application. (Standby
state)
● Low speed blinking (Light off 1 sec. Light on 1 sec.):
The
state
when
communicating
with the
application.
(Communicating
state)
●
High speed
blinking (Light
off 0.1 sec. Light on 0.1 sec.):
The
state
when the product failed to initialize and
cannot
communicate.
(Error
state)
● Lights off:
The
state
when the power is not
supplied
to the
product.
(Non-energized
state)
Wireless
LAN
connection
By using this product and
setup support software, primarily
the following items will be
realized
in
wireless
communica
-
tion.
・Edition of
parameters
for the servo
driver
・Monitoring the
operation
and inner
conditions
・Monitoring and clearing the
ala
rm
－ E14
－
－ E15
－
English
1. Introduction
(continued)
However, you
cannot
use the product in the
wireless
com
-
munication
for the function to drive the motor, such
as
com
-
missioning
or
frequency characteristics
measurement.
Since the function which is
available
varies
depending on
the using
application,
refer to the instruction
manual
of
each
setup support software
listed on the
website
for
details.
The product
cannot
be
connected
to the
Internet.
・
iPhone
is the
trademark
of Apple Inc.
registered
in
the
United
States
and other
countries.
The
trademark
of
iPhone
is
used based
on the
license
of Aiphone Co., Ltd.
・Android is the
trademark
or the
registered trademark
of
Google
Inc.
・Windows is the
registered trademark
or the
trademark
of
Microsoft
Corporation
in the United
States
and other
coun
-
tries.
・You can
download
“PANATERM”
applicable
to
Windows
OS from our
website.
・You can
download
“
P
anas
onic
Motor
Setup
App”
appli
-
cable to
iPhone
terminals from App
Store.
・For
“Panasonic
Motor
Setup
App”
applicable
to Android
terminals,
the
smartphone
version and tablet version
are
available.
You can
download
either one from Google
Play
.
2. Connection mode
You can use the STA mode (Station mode) with the
product.
● STA mode (Station mode)
This is the mode that this product
operates as
a
station
(Wireless
LAN
adapter)
and
communicates
with the
terminal
via the
equipment
that
operates as
an
access
point
(Wireless
LAN
access
point). When you
connect
in this mode,
please
separately prepare
the
equipment
which
operates as
an
ac
-
cess
point. In addition,
change
the network setting of the
ter
-
minal and internal
parameters
in the driver so
as
to
connect
with the
prepared access point.
In this mode, all the
products
in the
same
local
area network
can be
selected
from the
terminal.
Access point
－ E16
－
－ E17
－
English
2. Connection mode
(continued)
The
access
point to be
prepared shall
s
at
is
f
y all the
f
ol-
l
ow
i
ng
specifications.
If
the fo
ll
o
win
g
spe
cifica
ti
o
ns
are
n
ot
satisfied, change
the
access
point setting or
prepare other
access point.
・The
wireless communication standard supports
either
IEEE 802 11 n, g or
b.
・The security protocol
supports
either WPA or
WP
A2.
・Use 2.4 GHz band
as
the
frequency range
(5 GHz band
is
prohibited to
use).
・
Communications between
terminals
located
in the
same
local
area
is
permitted.
For
recommended access
points,
please
check them on
our
website.
3. Connection
Connect
the product to the
connector
X1 of the servo
driver
.
When servo driver is
connected
by
wireless
for the first
time,
initial
setup
is
necessary.
Refer to “4. Setting” for
details.
Connector X1
Product
Requests
Do not hook or place other wiring on the main body of
product.
Wireless LAN Dongle
Cable
－ E18
－
－ E19
－
Item
Description
Remarks
Security
Select
either WPA or
WP
A2.
Select
to match the setting of
the terminal and
access point.
Default:
WP
A
Country
code
Select
the country to use
the
product.
Please
set with
great
care
because
it
will
be
the
violation of law
if
you set
the
wrong country
code.
Default:
JP
SSID
Match to SSID of the
access
point to be connected.
Settable number of
characters:
1 to 32
characters
Accepted
characters:
half-width
characters
0 to
9,
a to z,
A
to Z, -,
_
Default:
Panasonic
Servo000
(
(
English
)
)
4. Setting
The servo driver has the
parameter
for setting the
wireless
LAN
communications as
the internal
parameters.
Before
starting the
wireless communications
with the product, it
is
required
to set (Initial
setup)
the
parameters
for
wireless
LAN
communications
by the use of USB
communication.
The following
section shows
the initial
setup method.
For
the
initial
setup,
you
need
to install the
setup support software,
and at the
same
time the terminal (i.e. Windows PC or An-
droid terminal) that can use the USB
communication
and
a
USB mini-B cable is
required.
1 Initial setup (Wired connection)
1.
Connect
the servo driver and terminal with the USB mini-
B cable.
Use a USB mini-B type in the
marketplace as
the
driver
side
connector. Select
the terminal side
connector
to
match to the
specifications
of the
terminal.
2. Start up the
setup support software
to start the
communi
-
cations
with the
driver
.
3. Set the following
parameters
on the “Wireless LAN/Driver
Information Setting”
screen
of the
setup support software
and then write
those parameters
in EEPROM of
driver
.
Connector X1 USB mini-B
cable
Prepare a cable
on the market.
PC
Connector X1 USB mini-B
cable
Prepare a cable
on the market.
Android terminal
－ E20
－
－ E21
－
Item
Description
Remarks
PWD
Match to the
password
of
the
access point to be connected.
Settable number of
characters:
8 to 32
characters
(*)
Accepted
characters:
half-width
characters
0 to
9,
a to z,
A
to Z, -, _,
!,
@, #,
$,
%, ^, *, ,, ., /
Default:
Panasonic
Servo000
DHCP
When it is set valid, the IP
ad
-
dresses
are
automatically
as
-
signed
from the
access point.
When it is set invalid, you
are
required
to set the IP
address
manually
.
Default: Valid
IP
address
Set the IP
address
to be
used
when DHCP is invalid.
Set only
when
DHCP
i
s
i
nval
i
d
Default:
192.168.0.1
Subnet
mask
Set the
subnet
mask to
be
used
when DHCP is invalid.
Set only
when
DHCP
i
s
i
nval
i
d
Default:
255.255.255.0
Default
gateway
Set the default
gateway
to
be
used
when DHCP is invalid.
Set only
when
DHCP
i
s
i
nval
i
d
Default:
192.168.0.1
English
4. Setting (continued)
Item
Description
Remarks
PIN
code
Set the PIN code which is
re
-
quired when the
setup support
software
is
used
by
wireless
connection.
At the start of
wireless commu
-
nication, the function
cannot
be
used
by
wireless
communi
-
cation
if
the PIN code set
here
is not input.
Also, the function
cannot
be
used
by
wireless communica
-
tion
if
the PIN code has
not
been set.
Settable number of
characters:
8
characters
(*)
Accepted
characters:
half-width
characters
0 to
9,
a to z,
A
to Z
Default:
Not set up
Driver
nickname
Set the driver
nickname which
is indicated on the setup sup-
port
software.
Settable number of
characters:
1 to 8
characters
Accepted
characters:
half-width
characters
0 to
9,
a to z,
A
to Z, -,
_
Default:
NoName
Setting
is
voluntary
.
*
To
ensure
the
safety
on the
security, set
the
password
a
nd
PIN code for the
access
point in the long and
complicated
character
string
as
much
as possible.
－ E22
－
－ E23
－
Power
supply
DC 5V
(Supplied
from USB) 500 mA
Power
consumption
Max.2500 mW
Outline
dimensions
39.4
31.9
Unit: mm
Weight
Appr. 4
g
Ambient
temperature
for use
Temperature
for
use:
0 °C – 55 °C (Shall be no
freeze)
Temperature
for
storage:
–20 °C – 65 °C
(Sh
al
l
be no
cond
e
n
sa
ti
on
)
Ambient
humidity for
use
20 % – 85 % RH both for use and
storage
(Shall be no
condensation)
Interface
USB mini-B
Standards
Conformable
to IEEE802.
1
1b/IEEE802.
11g/IEEE802.
11n
English
9.9
13
4. Setting (continued)
4. Turn
off
the power supply of
d
river
.
The initial
setup
is now
completed.
Next,
establish
the
wireless system between
the
terminal
and driver by using the
product.
5.
General
Specifications
1. Turn on the power supply of
access point.
2.
Connect
the product to the
connector
X1 of the
driver
.
3. Turn on the power supply of driver and check that t
he
lamp of the product lights
up.
4.
Change
the network setting of the terminal you want
to
use and
connect
to the target
access point.
5. Use the terminal to start up the
setup support software.
6. When the
communication
with the product has
been
suc
-
ceeded,
the
nickname,
part
number
and serial
number
of
the
corresponding
driver will be
displayed
on the
driver
select screen.
7. When the driver is
selected
which is the target to
connect,
the entry of PIN code will be
requested,
and so enter
the
PIN code you set at the initial
setup.
8. When the correct PIN code
i
s
i
np
ut,
the main
screen
o
f
the
setup support software
will
open.
Afterward,
parameter
setting or
status
monitoring can
be
carried out by
wireless communications
by using the
setup
support software.
For the
method
to use the
setup support software,
sepa
-
rately refer to the
operating manual
of
each setup support
software.
－ E24
－
－ E25
－
English
5. General Specifications (continued)
Frequency
range/Chan-
nels (Center
frequency)
2.412 GHz – 2.462
GHz
1 – 11 ch
Data transfer
speed
(Value of
standard *1)
IEEE802.11b:
Max.11
Mbps
IEEE802.11g:
Max.54
Mbps
IEEE802.11n:
Max.72.2
Mbps
Access
system
Infrastructure
mode
Security
WPA-PSK (TKIP/AES)
/WPA2-PSK (TKIP/AES)
Max.
trans
-
mission
distance
(Prospect)
Indoors: Appr. 20 m (Varies
depending on
the installation
circumstances)
*
１ This is the
theoretical speed
and the actual
communica
-
tion
speed
differs due to the
usage circumstances
or
the
connected equipment.
6. When you are in
trouble
Q.
I
connected
the product to the driver and then turned
on
the power supply but the lamp of the product
does not
light up (Power is not
supplied).
Or the lamp
immediately
lights off.
A. The servo driver may not
support
the product. For
the
supported
servo drivers,
please
check them on our
web
-
site.
Q. The lamp of the product blinks at a high
speed
and
the
communication
is
impossible.
A. The servo driver fails to read the
parameters
for
setting
wireless communications. Contact
failure with the
con
-
nector X1 may have
occurred, therefore, reinsert
the
product and then turn on the power supply
again.
When the
syndrome
is not
i
mpro
ved
even
if
the
a
bove
action was taken, the servo driver may not be
supported
in the
system. Please
check the
supported
servo
drivers
on our
website.
Q. The lamp of the product lights up, but the
communication
is
impossible.
A.
Communication
setting may be wrong. First of all,
check
the
wireless
LAN/driver
parameter
setting of the
servo
driver and check
whether
the
SSID/password
of
the
access
po
i
nt
and
parameter setting
of
the driver
a
re
matched,
and
whether
the security protocol
satisfies the
setting of
access point.
Check
if
the
same
IP
address as
other
equipment
ha
s
been
set when DHCP is set invalid and the IP
address is
set
manually
.
－ E26
－
－ E27
－
English
6. When you are in trouble (continued)
However,
if
the situation is not still improved,
check
whether
the network setting of the terminal is set to
con
-
nect to the target
access point.
Also check that the
access
point is in
accordance
with
the
specifications
for
access
point
as described before.
Q.
Wireless communication breaks
up during
com
munic
a
-
tions.
A. The
wireless communication circumstances
may be in
the
interference.
Check
if
the situation can be
improved
by the
method
to
change
the
communication channel or
eliminate the
interference
of
communications
after
stop
-
ping the
wireless communication
of other
equipment.
Electric wave may be blocked
off
by
obstacles.
Since
the
metal has property difficult to transmit the electric
wave
in particular, the
wireless communication
may be
impos
-
sible
if
the
circumstances
are
covered
by
metal.
Guarantee
Guarantee
period
● The
guarantee
period of the product
sh
al
l
be one
yea
r
after your
purchase
or one year and six
months
after
our
manufacturing month.
Guarantee
description
● We will
replace
the product without
charge
when a
failure
occurred
in the
guarantee
period in the normal
use
situation in
accordance
with this
operation manual.
However, the following
cases
shall be
charged
even
if
it
is
in the
guarantee period.
(1)
Failures caused
by the wrong
usage method
and
improper repair or
remodeling.
(2)
Failures caused
by the fall after the
purchase and
damages
during the
transportation.
(3)
Failures caused because
the product is
used beyond
the
scope
of
specifications.
(4)
Failures caused
by fire,
earthquake,
lightning
strike,
wind and flood, brine
damage, abnormal
voltage
or
other Acts of God and
disasters.
(5)
Failures caused
by the intrusion of water, oil,
met
al
fragments
or other foreign
matters.
● The
scope
of the
guarantee
shall be only for the
delivered
product unit. The
damage induced
by the
f
ailure
of t
he
delivered
product shall be out of the
scope.
－ E28
－
－ E29
－
English
Precautions
for
use
●
Cautions
to export the product or the
equipment installed
with the
product.
When the final user or the final
application
of the
product
is involved in the military affair or
weapons,
make sure
to
take the sufficient
probation
and
required
export
proce
-
dures because
the situation may be
subject
to the
export
control
regulated
by the
“
Foreign
Exchange
and
Foreign
Trade Control Law.”
● The product is
manufactured
only aiming at the use for
general
industria
l
products
but not
designed
or
manufac
-
tured for the
purpose
to be
used
with the
equipment
or
the
system
involving
human lives.
● The
specialist
who has the
knowledge
shall perform
deal
-
ing with the product such
as
the installation, wiring,
opera
-
tion,
maintenance
and
inspection.
● To apply to the facility where the
occurrence
of
serious
accident
or
damage
is
forecasted
due to the failure of
the
product, make sure to install the safety
device.
●
If
you
conduct
a study on the use of product in the
special
c
ir
c
um
s
t
anc
es
as
for
the
nuclear energy
control,
aer
o
-
space instruments, transport
facilities, medical
equipment,
various safety
devices
and
equipment
that
demands
the
cleanness class, please contact
us.
● We make our maximum effort to
ensure
the quality of
the
product,
however, please
take it into
consideration
to
es
-
tablish your fail safe
design
and
ensure
the safety in
the
operable range
at the
operation
place
because
the
product
may
generate unexpected actions caused
by the
loading
of
external
noise or static electrical
charge exceeding ex
-
pectation
or the
possible
failure of the input power
source,
wiring or
parts.
● The
wireless communications
may break out and the
f
unc
-
tion may not be
accomplished
normally due to the
inter
-
ference
in the
wireless communication circumstances
or
the
cause
that the far
distance between
the product
and
access
point or the
access
point and terminal,
communi
-
cation
interception
by
obstacles
such
as
the metal
which
blocks electric
waves,
failure
of
the terminal or
a
ccess
points. When the
communication breaks
out,
please check
the using
wireless communication circumstances
and
the
condition of using terminals and
access points.
● Since this product
uses
radio wave and it may
generate
unexpected actions
by the delay
unt
il
the result is
reflect
ed
actually on the
movement
of
equipment
when the
setting
change
is carried out,
please
check there are no
people
around
the site when the setting is
changed
and
please
take it into
consideration
to
ensure
the
safety.
●
Smoke
of a
cigarette
may be
generated depending
on
the
content
of
f
ailur
e
of the
product.
Give
consideration
to it
when the product is
used
in a clean
room.
● When the product is
used
in the
environment
where
the
concentration
of sulfur or
sulfide-based
gas (H2S,
SO
2
,
NO2, Cl2 etc) is high,
please
take the
conditions
into
ac
-
count
because
the
disconnection
of chip
resistor
or
bad
contact
of
contacts
by the sulfurization may
occur.
● For the
matching
of
structure, dimensions, lifespan, char
-
acteristics
and laws and
regulations
with the
inst
alling
equipment
and parts, or the
matching
when the
specifica
-
tion of installing
equipment
is
changed, please
make
the
final
decision
by the
customer.
● We
cannot guarantee
the use
beyond
the
scope
of
speci
-
fications of the product.
Please
use the product with
great
care.
● A part may be partially
changed
to improve the
perfor
-
mance.
● Do not
disassemble
or
remodel
the product
because
it
is
prohibited by the Radio Act.
－ E30
－
－ E31
－
Federal Communication Commission Interference Statement
● This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
● This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help.
● FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user's authority to operate this equipment.
● This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
● Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set
forth for an uncontrolled environment and are safe for intended
operation as described in this manual. The further RF exposure
reduction can be achieved if the product can be kept as far as
possible from the user body or set the device to lower output
power if such function is available.
English
After-sales service
Repair
.
•
Consult
to
a dealer
from whom you
have purchased the
product
for
details
of
repair.
MEMO
Wh
e
n
th
e
p
ro
d
u
ct
i
s
i
n
co
rp
o
ra
te
d
to
th
e
machi
ne
or
equipment
you
have purchased, consult
to
the
manufacturer
or the
dealer
of the
machine
or
equipment.
Technical information
•
Technical inf ormation
of this
product
(Operating
Instructions,
CAD
data,
Inquiries) can be
dow
nl
o
ade
d
from the following web
site.
https://industrial.panasonic.com/ww/products/motors-
compressors/fa-motors
■ Convenient note (Write in for your inquiry or
repair
.)
Date of
purchase
Part
No.
DV0PM20105
Purchase
store
name
Phone:
（ ） －
－ E32
－
IME98
Z1016-0
パナソニック株式会社
モータビジネスユニット
〒
574-0044 大阪府大東市諸福７丁目１番１号
電話（代表）
（072）871-1212
松下电器产业株式会社
马达经营单位
日本大阪府大东市诸福
7
丁目
1
番
1
号 邮编
574-0044
电话 +81-72-871-1212（总机）
Motor
B
u
s
i
n
e
ss
U
n
i
t
,
P
a
n
a
s
on
i
c
C
o
r
po
r
a
t
i
on
7-1-1 Morofuku, Daito City,
Osaka, 574-0044,
Japan
Phone
:
+81-72-871-1212
制造商 ：珠海松下马达有限公司
中国广东省珠海市南屏科技工业园屏东
3
路
3
号
原产地 ：中国
©
Panasonic Corporation 2016
Printed in
China
IME98
Z1016-0

Navigation menu