Panasonic WV CW374 User Manual To The 6ace85a8 7b81 4f81 B01f 2fe00e8190f2
User Manual: Panasonic WV-CW374 to the manual
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
To facilitate wirings, it is recommended to align two junction boxes.
Fixing the camera, camera mounting arm, and adapter box
As the factory default, the camera head has been tilted to the downside.
74
W3
-C
WV
Color CCTV Camera
Instructions
II
SD
The camera can be mounted either of the following ways.
• Using the supplied adapter box.
• Fixing the camera mounting arm directly
1. Move the camera head, as shown in the illustrations, by loosening the tilting lock screw.
Hole
6 mm (W) x 10 mm (H)
{1/4" (W) x 13/32" (H)}
46 mm {1-13/16"}
83.5 mm
{3-5/16"}
■ Preparations
Caution: When installing, the power cord is NOT to be exposed to outdoor conditions like frost and
sunlight.
4
37
W
V-C
W
Using the supplied adapter box
Camera head
Junction
box
I
I
SD
Model No.
WV-CW374
Notes:
• Mounting screws are not supplied. Prepare locally procured screws matching the material,
structure, and total weight of mounting place.
• Screws to fix the camera mounting arm to the adapter box are supplied.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
N0504-0
3TR002485AAA
When you mount the camera on a flat wall with a cable access hole, or through exposed wirings,
you will use the supplied adapter box. For installation, refer to Installation of Camera and Adapter
Box.
Mounting screws
(Locally procured) x 4
Tilting lock screw
(Hexagon socket screw)
2. After adjustment, tighten the tilting lock screw again.
3. Attach the camera mounting arm to the left or right hinges of adapter box, so that the mounting
arm can be opened and closed flexibly. (Refer to the illustration in Step 4.)
Printed in Japan
Fixing the supplied camera mounting arm directly
• You can fix the camera mounting arm to a junction box installed on the wall.
• You can fix the camera mounting arm directly to the wall with a cable access hole.
For installation, refer to Fixing the Mounting Arm Directly.
Caution:
Before attempting to connect or operate this
product, please read the marking on the top.
4. Fix the camera to the camera mounting arm.
Fixing screw for adapter box
(Supplied) x1
(M4 x 35)
For U.S.A
SA 1965
SA 1966
The lightning flash with arrowhead
symbol, within an equilateral triangle, is interned to alert the user to
the presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
FCC Caution: To assure continued compliance,
(example - use only shielded interface cables when
connecting to computer or peripheral devices). Any
changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate this equipment.
The serial number of this product may be found on
the top of the unit.
You should note the serial number of this unit in the
space provided and retain this instruction as a permanent record of your purchase to aid identification
in the event of theft.
■ Installation of Camera and Adapter Box
Notes:
• For outdoor use, the mounting screws and screw holes require waterproofing. Refer to
Waterproofing Process in this document.
• When wiring the camera cables through the adapter box, use a cable access hole. The cable
access hole is G3/4.
Fixing screws for camera
(Supplied) x 3
(M4 x 8)
W
V-C
W
37
Hinges
1. Fix the camera mounting arm to the adapter box with four supplied screws.
2. Fix the mounting arm covers to the mounting arm with two supplied screws.
I
I
SD
Adapter box
Installing the adapter box directly to the wall
With the mounting screws (locally procured), fix the adapter box to a junction box or directly to the
wall.
Mounting arm
Mounting arm
Note: Lead the camera cables out of the cable hole of mounting arm.
46 mm {1-13/16”}
Cable access hole
Hole
6 mm (W) x 10 mm (H)
{1/4” (W) x 13/32” (H)}
Adapter box
5. Pass the cables through the cable clamp of mounting arm, and then to the wall.
4
37
W
V-C
W
Model No.
Serial No.
I
I
SD
Center of
adapter box
Fixing screws for adapter box and
mounting arm (Supplied) x 4 (M5 x 20)
WARNING: All work related to the installation of this product should be made by qualified service personnel or system installers.
CAUTION: An ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm {0.12"} in each pole shall be
incorporated in the electrical installation of the building.
■ Fixing the Camera Mounting Arm and Adapter Box
4
83.5 mm
{3-5/16"}
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Note: The waterproof process should be made by qualified service personnel or system installers
according to the local requirement.
24.5 mm
{31/32"}
RISK OF ELECTRIC
SHOCK DO NOT OPEN
Screw-holes, cable access holes, and gaps:
Fill these portions with silicon rubber or equivalent waterproofing material.
Camera
22 mm
{14/16"}
CAUTION
■ Waterproof Process
Apply waterproofing to the necessary portions, using appropriate materials.
This camera is applied to IP66 only when installed according to the instructions in this document,
and appropriate waterproofing is applied.
Note: Attach the mounting arm to hinges on the side opposite to the wall.
Note: Mounting screws are not supplied. Prepare locally procured screws matching the material,
structure, and total weight of mounting place.
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interference
at his own expense.
Mounting arm
Fixing screws for covers
(Supplied) x 2 (M3 x 6)
Cable clamp
Mounting screws
(Locally procured) x 4
Covers x 2
Adapter box
Cable access hole
(Used for wiring)
(G3/4" internal thread)
Note: Do not expose the cables to sunlight.
■ Adjusting the Camera Angle
Installing the adapter box to a junction box
To facilitate wirings, it is recommended to align two junction boxes.
Panasonic WV-CW374 is designed for installation on the wall, using a camera mounting arm or the
supplied adapter box.
Hole
6 mm (W) x 10 mm (H)
{1/4" (W) x 13/32" (H)}
• Refer all work related to the installation of this product to qualified service personnel or
system installers.
Notes:
• For outdoor use, the mounting screws and screw holes require waterproofing. Refer to
Waterproof Process in this document.
• Avoid waterproofing the drainage hole.
1. Remove the rear cover by loosening the fixing screw.
(2) Remove the rear cover. (1) Remove the fixing screw.
Mounting arm
• Do not operate the appliance beyond its specified temperature, humidity, or power
source ratings.
Use the camera at temperatures between –30 °C and +50 °C {between –22 °F and 122 °F}, and
humidity below 90 %. The input power source for this appliance is 12 V DC/24V AC 60 Hz for
WV-CW374.
Drainage hole
Junction box
With the mounting screws (locally procured), fix the camera mounting arm directly to a wall or a
junction box installed on the wall.
When you install the camera in a low-temperature location and start operating it, it may take
time (around 30 minutes) for the inside of the camera to warm up. Cut power once then supply
power again.
• Screws to mount the camera is not supplied.
Prepare locally procured screws matching the material, structure, and total weight of mounting
place.
■ Fixing the Mounting Arm Directly
Mounting screws
(Locally procured) x 4
Hole
6 mm (W) x 10 mm (H)
{1/4" (W) x 13/32" (H)}
24.5 mm
{31/32"}
■ Precautions
46 mm {1-13/16"}
83.5mm
{3-5/16"}
■ Preface
CAUTION
46 mm {1-13/16"}
83.5 mm
{3-5/16"}
V-C
W
37
4
I
I
SD
Mounting screws
(Locally procured) x 4
(1) Remove the fixing screw. (x 2)
Cable access hole
• Be sure to use a ceiling board having enough strength to support this camera.
W
2. Remove the switch cover by loosening the two fixing screws.
The switch unit will appear.
Mounting arm
(2) Remove the switch cover.
3. Connect the video input jack of LCD monitor and the monitor output jack (3.5 mm
{0.14"} diam. minijack) of camera with a 2pole cable.
9mm {11/32"}
or less
Note: Refer to the illustrations for the width
of plug to be inserted into the video
input jack.
9mm {11/32"}
or less
■ Connections
■ Attaching the Supplied Sun Shield
Perform cable connections by referring the illustrations.
Attach the sun shield to the camera head by
tightening the four supplied screws.
L-type plug
Caution: Be sure to use the four supplied
screws.
Straight plug
Fixing screws
(Supplied) x 4
(M3 x 6)
Aim the arrow to
this direction.
Sun shield
4. Adjust the camera angle by performing 1) to 3).
24 V AC/12 V DC
2) While holding the camera head, loosen the tilting lock screw. Tilting becomes adjustable. Then,
move the camera head vertically.
Brown (Live/!)
Blue (Neutral/@)
Green/Yellow (GND)
Black (Live)
For heater
Gray (Neutral)
(24 V AC only)
T
WV-CW374
1) While holding the camera head, loosen the panning lock screw. Panning becomes adjustable.
Then, move the camera head horizontally.
FR
ON
Video Output cable
BNC plug BNC plug
W
BNC plug
To Video IN (CAMERA IN)
V-C
W
37
4
I
I
SD
3) After adjustments, tighten the panning and
tilting lock screws.
Camera head
Tilting lock screw
(Hexagon socket screw)
Notes:
• When loosening the panning and tilting lock screws, give only one turn.
• While a LCD monitor is connected to
the camera, You cannot check images
on a monitor connected to the video
output cable.
• After adjusting the panning and tilting,
adjust the focus. (Refer to Adjusting
the Focus.)
● Video Output Connection
■ Attaching the Supplied Mounting Adapter
Connect the video output connector to the monitor or other system device with the procured coaxial
cable. The maximum extensible length is shown in the table.
If you use a camera mounting arm locally procured, you need to use the supplied mounting adapter.
Type of coaxial
cable
Recommended (m)
maximum
cable length
(ft)
Panning lock screw
(Hexagon socket screw)
RG-59/U
(3C-2V)
RG-6/U
(5C-2V)
RG-11/U
(7C-2V)
RG-15/U
(10C-2V)
250
500
600
800
825
1 650
1 980
2 640
1. Remove the camera neck from the camera
head by loosening the camera neck screws.
2. Attach the supplied mounting adapter to the
camera head by tightening the four supplied
screws.
W
V-C
W
37
4
I
I
SD
● Cable Length and Wire Gauge
24 V AC
The recommended cable length and thickness are shown in the table for reference. The voltage
supplied to the power terminals should be within 19.5 V AC and 28 V AC.
■ Adjusting the Focus
1. Remove the front cover by loosening the
four fixing screws. Lens focus becomes
adjustable.
Recommended wire gauge for 24 V AC line.
Front cover
Copper wire size
(AWG)
Length of
Cable
(Approx.)
2. Adjust the lens zooming by moving the
zooming ring to T (Tele) or W (Wide).
3. Adjust the lens focus by performing 1) to
3).
#24
#22
#20
#18
(0.22 mm2) (0.33 mm2) (0.52 mm2) (0.83 mm2)
(m)
20
30
45
75
(ft)
65
100
160
260
Cautions:
• Be sure to use the supplied screws. Longer
screws may damage inner components, or
shorter screws may cause camera drop.
• You cannot use camera neck screws to attach
the mounting adapter to the camera unit.
Notes:
• Lead the cables out of the camera head.
• When separating the camera neck, remove the
panning lock screw and tilting lock screw.
Then, remove the three screws inside the camera neck.
Mounting adapter
(Supplied)
Fixing screws
(Supplied) x 4
(M3 x 8)
Remove the camera neck and
camera neck screws.
12 V DC
Use the formula below to calculate the power cable and power supply. The voltage supplied to the
power terminals of the camera should be within 10.5 V DC and 16 V DC.
1) Loosen the focus lock screw.
The focus lever, locked with the focus lock
screw, will be adjustable.
Loosen these screws.
Resistance of copper wire [at 20 °C (68 °F)]
Copper wire size
(AWG)
2) Move the focus lever to F (Far) or N (Near).
Focus lock screw
(Locking the focus lever)
3) After adjustment, tighten the focus lock
screw.
Zooming ring
Note: To change the lens zooming or
focus, perform Step 2 and 3 again.
F
T
N
W
#24
#22
#20
#18
(0.22 mm2) (0.33 mm2) (0.52 mm2) (0.83 mm2)
Resistance Ω/m
0.078
0.050
0.03
0.018
Resistance Ω/ft
0.026
0.017
0.010
0.006
10.5 V DC ≤ VA - 2(R x I x L) ≤ 16 V DC
L
: Cable length (m) (ft)
R
: Resistance of copper wire (Ω/m) (Ω/ft)
VA : DC output voltage of power supply unit
I
: DC current consumption (A). See specifications.
■ Specifications
Dimensions:
Weights:
78 mm (H) x 82 mm (W) x 301 mm (D)
{3-1/16" (H) 3-1/4" (W) 11-7/8" (L)}
1.3 kg {2.9 lbs.}
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
CAUTIONS
1. Shrinking the cable-entry seal is a one-time procedure. Do not shrink the cable-entry seal
until it has been ascertained that the unit is functioning.
CONNECT THIS TO CLASS 2 POWER SUPPLY ONLY.
2. All interconnecting devices must be UL Listed.
■ Attaching the Switch, Rear, and Front Covers
Attach the switch, rear, and front covers to the camera with the screws you have removed.
Switch cover attachment
Perform Step 2 of "Adjusting the Camera Angle" reversely.
Rear cover attachment
■ Standard Accessories
Instructions (this document)............................................................... 1 pc.
Operating Instructions........................................................................ 1 pc.
The following are for installation.
Sun shield........................................................................................... 1 pc.
Mounting arm ..................................................................................... 1 pc.
Adapter box........................................................................................ 1 pc.
Mounting adapter ............................................................................... 1 pc.
Cover .................................................................................................. 2 pcs
Fixing screws for camera (M4 x 8) .................................................... 3 pcs.
Fixing screws for adapter box (M4 x 35) ........................................... 1 pc.
Fixing screws for adapter box and mounting arm (M5 x 20) ............ 4 pcs.
Fixing screws for covers (M3 x 6) ..................................................... 2 pcs.
Fixing screws for sun shield (M3 x 6) ................................................ 4 pcs.
Fixing screws for mounting adapter (M3 x 8) .................................... 4 pcs.
Perform Step 1 of "Adjusting the Camera Angle" reversely.
Front cover attachment
Perform Step 1 of "Adjusting the Focus" reversely.
Notes:
• The recommended tightening torque of switch cover fixing screws (x 2) and front cover fixing
screws (x 4) is 0.59 Nm {0.43 lb ft.}.
• Tighten the front cover with the fixing screws in the order from q to r two times. (Refer to the
illustration.)
e
q
CAUTION
Panasonic Digital Communications & Security Company
Unit of Matsushita Electric Corporation of America
Security Systems Group
www.panasonic.com/cctv
Switch cover
Fixing screws x 2
Switch cover attachment
Rear cover
w
r
Fixing screw x 1
Rear cover attachment
Front cover attachment
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Zone Office
Eastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205
Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
2004
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina,
P.R. 00985 (809)750-4300
© Matsushita Electric Industrial Co., Ltd. All rights reserved.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2006:06:27 18:30:10Z Creator : QuarkXPress(tm) 4.1r2 Modify Date : 2006:06:27 18:55:08+09:00 Page Count : 2 Creation Date : 2006:06:27 18:30:10Z Producer : Acrobat Distiller 4.05 for Macintosh Mod Date : 2006:06:27 18:55:08+09:00 Metadata Date : 2006:06:27 18:55:08+09:00 Page Mode : UseOutlines Page Layout : SinglePageEXIF Metadata provided by EXIF.tools