Panda Wireless LGPAU05 Panda Wireless 300Mbps Wireless N USB Adapter User Manual 54Mbps

Download:
Mirror Download [FCC.gov]
Document ID	2690621
Application ID	iIo1tsiTt25JYooW3Co/sw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	103.54kB (1294218 bits)
Date Submitted	2015-07-23 00:00:00
Date Available	2015-07-23 00:00:00
Creation Date	2015-07-22 14:37:41
Producing Software	Adobe Acrobat Pro 9.1.2
Document Lastmod	2015-07-22 14:47:54
Document Title	54Mbps
Document Creator	Adobe Acrobat Pro 9.1.2
Document Author:	Zem

Mbps
54M/150M/300
54M/150M/300M
USB WIRELESS ADAPTER
User
User’’s Manual
(Ver 2.3)
Userʼs Manual
Wireless USB Adapte r
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
1. Introduction
Thank you for purchasing the IEEE 802.11b/g or 802.11n Wireless USB Adapter. This
Wireless Adapter is easy to use and easy to setup. If you have been tired of dealing with all
those messy wires to connect a laptop or PC to office or home network, this Wireless adapter is
an ideal access solution for wireless Internet connection.
A typical Internet access application for the USB wireless adapter is shown as the following
figure:
There are two different ways to access Internet:
1) With a wireless adaptor, receiving and transferring signal via a wireless router, then passed
to an ADSL modem, then to local ISP (Internet service supplier) through a telephone line.
Page 1
Userʼs Manual
Wireless USB Adapte r
2) With a wireless adaptor, receiving and transferring signal via local AP (Access Point) or so
called Hotpoint directly.
Tips: An 802.11 LAN is based on a cellular architecture where the system is subdivided into
cells, where each cell (called Basic Service Set or BSS) is controlled by a Base Station
(called Access Point, or in short AP).
2. Package Contents:
� One 54 Mbps 802.11b/g or 150Mbps or 300Mbps 802.11n USB Wireless Adapter.
� Adapter Installation disc.
� User’s Manual.
� Antenna (optional)
Warranty
The warrants for the end user (“Customer”) that this hardware product will be free from defects
in workmanship and materials, under normal use and service, for twelve (12) months from the
date of purchase from its authorized reseller. Information in this document is subject to change
without prior notice.
3. Installation
To install the driver of the USB adapter, please use administrator user account to login before
the following steps:
Tips: the latest original drivers can be down loaded from the website of Ralink chipset
manufacturer. The current website is http://www.ralinktech.com/en/04_support/support.php?sn=500 To find a
correct driver, please identify the chipset type applied in the adapter you have.
For Windows XP:
The system will detect a new hardware has been added, and start the “Found New
Cancel
Hardware Wizard
Wizard”. Click on “Cancel
Cancel”.
1)
Please insert the disc into your CD-ROM drive. The disc should auto start, displaying the
following window, If it does not start, open the browser window, find the autorun.exe file in
your CD-ROM folder, click to run it.
2)
Ralink has integrated all the 54Mbps 802.11b/g ,150Mbps or 300Mbps 802.11n driver into
Driver Installation
one file. Click to run the “Driver
Installation”
Notes: Because Ralink often updates software
software,, the drivers contained in the disc
might be changed without prior notice.
3)
Follow the instructions and prompts of the “InstallShield Wizard” to finish the driver
installation:
a. Select the “I accept the terms of the license agreements”, then click the “Next”.
Page 2
Userʼs Manual
Wireless USB Adapte r
b. There shows a setup type window, you can select “Install driver only” or “Install driver
and Ralink WLAN utility” and then click the “Next”.
Tips
Tips::
i. The Windows XP utilizes a "Wireless Zero Configuration( WZC)" Service built into
the operating system. Many wireless network adapter cards utilize this service.
ii. Ralink- the chipset manufacturer has developed a utility for setting up wireless
connection. If you select this item, you can switch between the Windows XP’s WZC
service and the Ralink WLAN utility service later.
c. Click the “Install” to confirm the installation, there shows the installation progress.
Page 3
Userʼs Manual
d. Click “finish” to finish the driver installation.
Page 4
Wireless USB Adapte r
Userʼs Manual
Wireless USB Adapte r
For Windows 7:
Once the wireless USB adapter be plugged into an USB port, the following message will
appear on screen.
The following installation procedures are similar to those of Windows XP. Please
refer to the installation steps for Windows XP.
4. Wireless Connection
For Windows XP:
1) After finishing driver installation, insert the USB adapter to Notebook or PC that supports
USB 2.0/1.1 interface.
Remarks: Make sure to connect the adapter to an USB port on your computer directly rather
than an USB hub. Although it might work when connecting with an USB hub, the likelihood of
configuration problems will be higher.
2) The system shows a wireless utility icon in the Windows system tray, which locates in the
bottom-right corner of your computer screen, and pops up a message that indicates a new
hardware is found and installed, something like this:
Should the service " Wireless Zero Configuration ( WZC)" be applied.
1) Before you begin, ensure WZC is enabled, by right-clicking on the Ralink icon
task bar in the bottom right corner of your screen.
in the
In the menu that appears, select "Use Zero Configuration as Configuration Utility" to use
Windows' wireless management feature, Windows Zero Configuration (WZC) helps to
manage your Wireless Network Connection.
2)
Right click the icon and then select “View Available Wireless Networks” to launch the utility,
the Wireless Network Connection window appears and displays your wireless network
listed with the SSID you chose.
Page 5
Userʼs Manual
Wireless USB Adapte r
Notes: Before configuring your WiFi access, you need to have your network’s SSID
(service set identifier), security key and authentication type handy. Check the
documentation coming with your router, ask your network administrator to get the
information.
3)
If you don't see your network, click “Refresh network list” in the upper left corner. If you are
locating within the valid range of hotspots or wireless routers, all available networks will be
recognized and listed automatically. Click your preferred network, and then click “Connect”
in the lower right corner.
4)
If the network security key hasn’t been inputted before, Windows XP prompts you to enter
the network’s security key to access the wanted SSID. Type the encryption key that you
wrote down earlier in both the Network key and Confirm network key boxes, and then click
“Connect”.
Tips: If there are free hotspots, simply select the network you want from the list
displayed, then click Connecting. It tries to launch your Internet browser—you should
be connected to the Internet.
If there is a pay hotspot, signing in or up will require either to enter your login information-if
you‘re an existing customer, or to enter your credit card information for payment, it is just
Page 6
Userʼs Manual
Wireless USB Adapte r
decided by you. Then clicking the Connecting, your default Internet browser will launch and
take you to the service provider’s login page. Most providers have very simple and
step-by-step instructions for you to sign up and then to be connected. Another way to access
the service provider’s login page is to simply launch your Internet browser, if there’s a pay
network available, you’ll be taken directly to the login page.
Should the service of Ralink wireless connection utility be applied.
1) After the installation of Ralink utility, the system shows a special wireless utility icon in the
Windows system tray, which locates in the bottom-right corner of your computer screen:
2) When an USB wireless adapter is inserted into an USB 2.0/1.1 port of Notebook or PC,
the icon changes colors according to the wireless signal quality.
3)
Double-click the icon or right click the icon and then select “Launch Config Utility” to
launch the utility, the RaUI window appears like:
The Ralink wireless utility starts in compact mode as shown above, provides profile
management, the available networks listing, a statistical counter display, Wi-Fi multimedia
(WMM), protected Wi-Fi setup, Cisco compatible extensions (CCX), call admission control
(CAC), radio controls, Ralink driver/utility information, and help functions. Clicking the
expanding icon
can change to the full mode as shown below:
In this utility, there are two applications can be selected: the Station mode and AP mode.
Page 7
Userʼs Manual
Wireless USB Adapte r
� Station mode (Client mode) : It is the default access way, the USB wireless adapter
servers as a client to access Internet through other router or AP.
� AP mode: It sets the USB wireless adapter as an AP, which allows the other users
can connect to Internet through your computer. Before using the mode, it must be
available that an existed Internet connection via wire Ethernet connection or by 3G
wireless connection.
Tips: Point the cursor to the Ralink icon located on bottom-right corner of your computer
screen, right click the mouse, from the pop up list, you can select the station mode or AP
mode.
4) Below are the steps to connect to a wireless network using the Ralink Utility.
i. Open the Ralink Utility by double-clicking on the Ralink Utility icon in the taskbar.
ii. The Ralink Utility appears, by default connected to an available open wireless network.
Check the name of the network to which you are connected. If this is the correct network,
no further steps are required.
iii. To connect to an alternative network, click the Available Networks button.
iv. In the Available Networks window that appears, select the name of the network to which
you are connecting. Then click the connect icon
Utility sets up a connection.
Page 8
and wait several seconds while the
Userʼs Manual
Wireless USB Adapte r
v. The Ralink Utility automatically detects and displays the security settings of the network to
which you are connecting in the Profile Settings screens.If the Utility shows that WPA-PSK or
WPA2-PSK security is detected as shown below, click the right arrow to save your settings.
vi. In the screen that displays, in the 'WPA Preshared Key' field, type a security key, the same
as that used by the AP or wireless router to which you are connecting. Click the right arrow
to save your settings and connect to the network.
vii. Once you are connected the Available Networks screen shows the status of your
connection.
Page 9
Userʼs Manual
Wireless USB Adapte r
For Windows 7:
s: Windows Zero Configuration (WZC) is not necessary in Windows Vista, Windows 7, or
Note
Notes
higher version OS, you can use WZC and the Ralink Utility to manage the adapter
simultaneously.
1)
Click on the wireless networks icon in the task bar in the bottom right hand corner of your
screen to display the available wireless networks.
2) Click the "Connect" button to connect to the selected network.
Page 10
Userʼs Manual
Wireless USB Adapte r
3) If your network has wireless security configured, enter the required settings. The following
is an example only, your network settings may differ.
4) The success of your connection is indicated by the wireless networks icon.
Notes: The steps of using the Ralink Utility to connect a wireless network is the same as those
described in Windows XP.
In addition to station and AP mode, there is the Client + AP Mode to be selected in Window 7 as
Page 11
Userʼs Manual
Wireless USB Adapte r
well.
Which means: other wireless devices connect to � Soft-AP of the adapter � the adapter
(client mode with internal ICS sharing) � connect to other AP or router� Internet.
This mode lets you use the adapter both as a Soft-AP and client at the same time. Switching to
this mode, you can let a wireless adapter be connected to a wireless network (Soft-AP) with
Internet connected, and let others adapter be indirectly connect to Internet via the Soft-AP
wireless network.
For more details about the RaUI utility, please read the help information
of the utility by clicking the
tap.
Page 12
Userʼs Manual
Wireless USB Adapte r
5. Tips for Wi-Fi users
With a Wi-Fi connection, you can roam about 150 m around the access point (depends on
different environment), so find a spot where you can work without any interruption. Then see
how much work you can do, such as:
�
Easily and quickly receive and transmit files within your local network — no problem
for big files.
�
Access your email and surf the web with the same speed as that connected with
network cables.
�
Synchronize data between devices.
�
Take advantage of wireless printing — send files directly from your laptop PC to a
wireless printer over Wi-Fi connection.
6. Warning
Wi-Fi offers greater speed and range than Bluetooth, but it drains your portable device
batteries a lot faster than Bluetooth does. In fact, if you use a Wi-Fi connection regularly on
your laptop PC, you'll undoubtedly notice that you need to recharge more often. If you need to
conserve battery life — on a long trip for example — turn off your Wi-Fi connection when you
don't actually need it.
7. Security
Because wireless networks rely on radio signals to transmit data, they are not as secure as
wire network. Wireless networks are susceptible to viruses and breaches like eavesdropping
and need to be protected in order to be secure.
There are many security measures to safeguard wireless networks, protect the data, and
keep unauthorized users out. Hotspots, on the other hand, are often free of standard security
practices in an effort to make it easy for anyone to connect. It may be found that some pay
hotspots administered by service providers offer have some level of security, however, when
using a hotspot, it’s always a good idea to be proactive and to employ security measures of
your own.
8. Key terms
Wi-Fi: Short for “wireless fidelity,” a generic label that refers to wireless networks or
networking.
Hotspot: A specific geographic location in which an access point provides public
wireless broadband network services to mobile visitors through a WLAN.
Throughput
Throughput::: The amount of data transmitted in a set amount of time.
Bandwidth
Bandwidth:: the amount of data that can be carried from one point to another in a given
time period (usually a second).
Chipset
Chipset::: A group of microchips that execute various functions (like memory) to support
the CPU.
Tx Power
Power：The transmit power measured at the terminal without antenna be considered.
Should the antenna gain be considered, the EIRP value is mentioned.
1T1R, 2T2R: The stream channel. 1T1R means one transmitter and one receiver. 2T2R
means two transmitters and two receivers.
Dual Band: Normally means 802.11b/g/n or 802.11a, which one works in 2.4GHz, and
other works in 5GHz.
Page 13
Userʼs Manual
Wireless USB Adapte r
9. Specifications (Typical):
Protocol and
Standards
IEEE 802.11b/g or 802.11n
Interface
USB1.1, USB2.0
Frequency Band
2.412~2.462GHz (Depends on different countries’ regulation)
For 802.11b/g: Peak rate 54Mbps, Peak throughput: 27Mbps.
Data Rate
For 802.11n
1T1R. Peak rate: 150Mbps, Peak throughput: 90Mbps
1T2R. Peak rate: 300Mbps, Peak throughput: Rx 160Mbps
2T2R. Peak rate: 300Mbps, Peak throughput: Rx 260Mbps
Transmit Power
(Typical) 802.11b: 19dBm; 802.11g:16dBm ; 802.11n: 15dBm.
Data Security
WEP 64/128 , WPA, WPA2, 802.1X
Power Consumption
It depends on different adapter models, there are two typical values:
330mA and 110mA in full Transmit (TX), 290mA and 95mA in full
Receive (RX)
Transmission
Distance
Indoor up to 100m, outdoor up to 300m (Standard transmission
distance, it is affected depending on different environment).
Environment
Operating Temperature: -10°C~60°C
Storage Temperature: -20~80°C
Operating Humidity: 10%~90% non-condensing
Storage Humidity: 5%~95% non-condensing
Operating System
It supports :
Windows XP/Vista/7/8，RT3x7x chipset supports Windows 2000;
(Win CE driver to be offered upon special requirement);
Mac OS X;
Linux (Android, Soft-AP, WPS driver need to be specially applied for)
Page 14
FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: PAU05
(FCC ID: 2ADUTLGPAU05) has also been tested against this SAR limit. The highest SAR value
reported under this standard during product certification for use on the body is 0.200W/kg.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Zem
Create Date                     : 2015:07:22 14:37:41+08:00
Modify Date                     : 2015:07:22 14:47:54+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2015:07:22 14:47:54+08:00
Creator Tool                    : Adobe Acrobat Pro 9.1.2
Format                          : application/pdf
Title                           : 54Mbps
Creator                         : Zem
Document ID                     : uuid:b9b9c5d5-6c68-4f2a-9796-61bff4c39753
Instance ID                     : uuid:0c5cf22d-6b5b-49b4-97dc-0dadf93b9ae9
Producer                        : Adobe Acrobat Pro 9.1.2
Page Count                      : 16

EXIF Metadata provided by EXIF.tools