Parabody 777 Users Manual 777102 Bk1a
777 to the manual 40b385d8-606f-4a98-9b53-f1f8b91e10dc
2014-12-13
: Parabody Parabody-777-Users-Manual-125576 parabody-777-users-manual-125576 parabody pdf
Open the PDF directly: View PDF 
.
Page Count: 28
| Download | |
| Open PDF In Browser | View PDF |
777 GYM SYSTEM WARNING: Read and follow all directions for each step to insure proper assembly of this product. USER’S GUIDE CLASS H PART # 7148201 REV. A 1 Version: 777102 Revision: 07/26/01 TABLE OF CONTENTS Safety Statement.............2 General Notes..................3 Tools Required................3 Gym Layout.....................4 Parts list..........................5 Assembly Instructions.....6-25 General Maintenance.......26 Warranty Statement..........27 Product Services..............28 Insert-Registration Card IMPORTANT SAFETY INFORMATION THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES! 1. Before using, read all the warnings and instructions on the use of this machine. Use only for intended exercise. DO NOT modify the machine. 6. Never pin the weights or prop plate into an elevated position. DO NOT use the machine if found in this condition. DO NOT attempt to fix. Notify your authorized ParaBody dealer. 2. Obtain a medical exam before beginning any exercise program. 7. Inspect cables and their connections before using machine. Pay particular attention to the cable ends. DO NOT attempt to fix. Notify your authorized ParaBody dealer before use and have repairs made by an authorized service technician. 3. Keep body and clothing free of all moving objects. 4. Inspect the machine before use. DO NOT use it if it appears damaged. DO NOT attempt to fix a broken or jammed machine. Notify your authorized ParaBody dealer before use and have repairs made by an authorized service technician. 8. Make sure all spring loaded pull pins are fully engaged in the adjustment position and fully tighten thumbscrew before use. 5. Be certain that weight pin is completely inserted. Use only the pin provided by the manufacturer. If unsure, call your authorized ParaBody dealer. 9. Children must not be allowed near this machine. Supervise teenagers. . NOTE: In a continual effort to improve our products, specifications are subject to change © 2001 Life Fitness, a division of Brunswick Corporation. All rights reserved. ParaBody is a trademark of Brunswick Corporation www.parabody.com 2 IMPORTANT NOTES Please note: * Thank you for purchasing the ParaBody 777 Gym System. Please read these instructions thoroughly and keep them for future reference. * This product must be assembled on a flat, level surface to assure its proper function. * Do not securely tighten any frame connections until the entire frame have been assembled unless otherwise specified. Tools Required for Assembly * Rubber mallet or hammer * 3/4” wrench * 9/16” wrench * Ratchet with 3/4” and 9/16” sockets * 5/32” Allen wrench * Adjustable wrench * Tape measure Bolt Length Ruler NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. BOLT LENGTH BOLT LENGTH RULER: 1/2 0 1/2 1 1/2 2 1/2 3 3 1/2 4 1/2 5 6 1’ 2’ 3’ 4’ 5’ 6’ 7’ 8’ 9’ 1’ 2’ 3’ 4’ 5’ 6’ 7’ 8’ 9’ 1 Square = 1’ X 1’ Minimum Required Usable Space Length Width Height = 90 inches (229 cm) 7’ 6” = 103 inches (262 cm) 8’ 7” = 84 inches (213.5 cm) 7” Dimensions Including Leg Press (optional) Length Width = 102 inches (259 cm) 8’ 6” = 130 inches (330 cm) 10’ 10” 4 PARTS LIST KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 DESCRIPTION QTY PAR T # BASE 1 70077 UPRIGHT 1 70076 SEAT ADJUST 1 70058 RIGHT ARM SUPPORT 1 70014 LEFT ARM SUPPORT 1 70015 RIGHT ARM 1 70017 LEFT ARM 1 70019 LEG PEDESTAL 1 70056 PULLEY BRACKET 1 70067 PULLEY PLATE 2 69408 BASE PLATE 2 69885 V-PULLEY PLATE 2 69954 BOOM PULLEY PLATE 2 69957 RIGHT BOOM PLATE 1 71552 LEFT BOOM PLATE 1 71553 PAD 2 69947 ROLLER PAD 6 6194601 76” GUIDE ROD 2 6816501 14-1/2” SEWN HANDLE 2 7016902 7-1/2” SEWN HANDLE 2 7016901 WEIGHT PLATE 15 6939202 3 6382301 WEIGHT PLATE BUSHING 10 CT HEAD PLATE 1 69537 E-RING 1 3221702 WEIGHT STACK LABEL 1 6978101 WEIGHT PLATE SHAFT 1 7095701 WEIGHT STACK PIN 1 6972201 WEIGHT STACK CUSHION 2 3108002 WEIGHT STACK CABLE 1 7155701 LEG CABLE 1 6987901 ARM CABLE 1 6988001 BOOM CABLE 1 6988101 WEIGHT STACK SPACER 2 7012102 3/4” FLAT WASHER 2 3102503 ANKLE STRAP 1 6409101 1/2 0 1/2 1 KEY 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 1/2 2 PART # 3103302 3116201 3116101 6993701 6412001 3103801 6416601 6145801 3105401 3108901 6866801 6866601 6480301 6480302 6122702 6122701 6549301 3102924 3102807 3102922 3221902 3102905 3102917 6075906 3102906 3102930 3102804 3102802 3102501 6020601 70718 3102904 3102955 3102514 71185 7122101 1/2 3 53 DESCRIPTION SHAFT COLLAR 3-1/2” PULLEY 4-1/2” PULLEY 4-1/2” V-GROOVE PULLEY SPRING PIN ASSEMBLY SNAP LINK PARAGLIDE (QTY 8) 3 PRONG KNOB STARLOCK PLASTIC WASHER 1/2” RH WASHER RH CAP 3/8” X 9/16” FLANGE SPACER 3/8 X 1-1/16” FLANGE SPACER 3/8 X 1/2” SPACER 3/8” X 1” SPACER 3/4 X 17” TUBE 3/8 X 1-3/4” BOLT 3/8 LOW HEIGHT LOCK NUT 3/8 X 2-3/4” BOLT 2” NYLON SPACER 3/8 X 3-3/4” BOLT 1/2 X 4” BOLT 12 LINK CHAIN 3/8 X 4” BOLT 3/8 X 7” BOLT 1/2” LOW HEIGHT LOCK NUT 3/8” LOCK NUT 3/8” FLAT WASHER 1/2” FLANGE BEARING FOOT PLATE 3/8 X 3” BOLT 3/8 X 4-1/4” BOLT 3/8” SAE WASHER GUIDE BRACKET GUIDE CABLE 1/2 4 1/2 5 6 QTY 2 14 3 4 1 6 1 1 6 2 2 2 2 2 6 11 3 4 2 16 4 17 1 1 2 1 1 36 14 2 1 2 2 4 1 2 2 57 3/8 X 3-3/4” 1 3/8 X 3” 67 11 48 63 63 66 FIGURE 1 STEP 1: • LOOSELY assemble two BASE PLATES (11) to the BASE (1) and the UPRIGHT (2) using four 3/8 X 3-3/4” BOLTS (57) and four 3/8” LOCK NUTS (63). See FIGURE 1. • Insert two two 3/8 X 9/16” FLANGE SPACERS (48) into the upper hole of the FRAME (2) as shown. • LOOSELY assemble the FOOTPLATE (66) to the FRAME (2) using one 3/8 X 3” BOLT (67) and one 3/8” LOCK NUT (63) as shown in FIGURE 1. 1/2 0 1/2 1 1/2 2 1/2 3 6 1/2 4 1/2 5 6 22 21 FIGURE 2 STEP 2: • Insert two WEIGHT PLATE BUSHINGS (22) into each of the fifteen WEIGHT PLATES (21) as shown in FIGURE 2. 24 23 26 FIGURE 3 STEP 3: • Slide the WEIGHT PLATE SHAFT (26) thru the hole in the HEAD PLATE(23), and lock in place using one E-RING (24) as shown in FIGURE 3. 7 36 18 23 21 28 34 33 777 SHROUD OPTION ONLY! 1 FIGURE 4 STEP 4: • Insert two GUIDE RODS (18) into the BASE (1) as shown on FIGURE 4. (NOTE: If the 777 SHROUD OPTION was purchased, place the GUIDE RODS (18) through the BOTTOM SHROUD BRACKET (found in SHROUD OPTION box) and into the BASE (1) as shown in FIGURE 4. • (NOTE: Lubricate GUIDE RODS (18) with silicon or teflon spray available at most hardware stores.) • Slide two WEIGHT STACK SPACERS (33), two 3/4” FLAT WASHERS (34), and two WEIGHT STACK CUSHIONS (28) down over the GUIDE RODS (18). • Using EXTREME CARE slide all fifteen WEIGHT PLATES (21) down over the GUIDE RODS (18) on to the WEIGHT STACK CUSHIONS (28). Make sure that the WEIGHT PLATES (21) are all facing as shown. • Slide the head plate assembly down over the GUIDE RODS (18) onto the weight stack. • Slide two SHAFT COLLARS (36) over the GUIDE RODS (18) as shown in FIGURE 4. 1/2 0 1/2 1 1/2 2 1/2 3 8 1/2 4 1/2 5 6 14 36 TIGHTEN! 15 3/8 X 3-3/4” 57 2 18 63 FIGURE 5 STEP 5: • Swing the GUIDE RODS (18) into the guide rod bushings in each of the RIGHT and LEFT BOOM PLATES (14 & 15) as shown in FIGURE 5. • LOOSELY assemble the RIGHT and LEFT BOOM PLATES (14 & 15) to the UPRIGHT (2) using three 3/8 X 3-3/4” BOLTS (57) and three 3/8” LOCK NUTS (63). See FIGURE 5. • Slide the SHAFT COLLARS (36) to the top of the GUIDE RODS (18) and tighten set screws as shown in FIGURE 5. FIGURE 6 4 25 5 63 1 64 3/8 X 3-3/4” 57 STEP 6: • LOOSELY assemble the RIGHT and LEFT ARM SUPPORTS (4 & 5) to the BASE (1) using four 3/8 X 3-3/4” BOLTS (57), four 3/8” FLAT WASHERS (64), and four 3/8” LOCK NUTS (63). See FIGURE 6. • Apply WEIGHT STACK LABELS (25) to the WEIGHT PLATES (21) as shown in FIGURE 6. 9 4 6 3/8 X 4” 60 7 5 64 2 54 FIGURE 7 STEP 7: • LOOSELY assemble the RIGHT and LEFT ARMS (6 & 7) to the UPRIGHT (2) and the RIGHT and LEFT ARM SUPPORTS (4 & 5) using two 3/8 X 4” BOLTS (60), four 3/8” FLAT WASHERS (64), and two 3/8” LOW HEIGHT LOCK NUTS (54). See FIGURE 7. 16 3 64 3/8 X 2-3/4” 55 FIGURE 8 STEP 8: • SECURELY assemble one SEAT PAD (16) to the SEAT ADJUST (3) using two 3/8 X 2-3/4” BOLTS (55) and two 3/8” WASHERS (64). See FIGURE 8. 1/2 0 1/2 1 1/2 2 1/2 3 10 1/2 4 1/2 5 6 3 42 43 2 FIGURE 9 40 STEP 9: • Securely assemble one SPRING PIN ASSEMBLY (40) and one 3 PRONG KNOB (43) to the FRONT UPRIGHT (2) as shown. • Apply eight PARAGLIDES (42) to the INSIDE of the tube on the UPRIGHT (2) and on the OUTSIDE of the SEAT ADJUST (3) as shown. • CAREFULLY insert the SEAT ADJUST ASSEMBLY into the UPRIGHT (2) as shown. The SEAT height can be adjusted using the SPRING PIN (40) and can be secured with the 3 PRONG KNOB (43). 47 46 1/2 X 4” 58 62 8 65 2 FIGURE 10 STEP 10: • Insert two 1/2” FLANGE BEARINGS (65) into the the LEG PEDESTAL (8) as shown in FIGURE 10. • Assemble the LEG PEDESTAL (8) to the UPRIGHT (2) using two RH CAPS (47), one 1/2 X 4” BOLT (58), two 1/2” RH WASHERS (46), and one 1/2” LOW HEIGHT LOCK NUT (62). (Note: Tighten this connection enough to remove excess play yet allow the LEG PEDESTAL to rotate freely.) 11 3/8 X 2-3/4” 55 12 39 2 FIGURE 11 STEP 11: • Assemble two V-PULLEY PLATES (12) and two 4-1/2” V-GROOVE PULLEYS (39) to the UPRIGHT (2) using two 3/8 X 2-3/4” BOLTS (55) . See FIGURE 11. 51 3/8 X 7” 61 13 37 50 63 15 FIGURE 12 STEP 12: • Assemble two BOOM PULLEY PLATES (13) and three 3-1/2” PULLEYS (37) to the BOOM PLATES (14 & 15) using one 3/8 X 7” BOLT (61), two 3/8 X 1/2” SPACERS (50), two 3/8 X 1” SPACERS (51) and one 3/8” LOCK NUT (63) . See FIGURE 12. 1/2 0 1/2 1 1/2 2 1/2 3 12 1/2 4 1/2 5 6 38 51 3/8 X 3-3/4” 57 63 15 FIGURE 13 STEP 13: • Assemble one 4-1/2” PULLEY (38) to the BOOM PLATES (14 & 15) using one 3/8 X 3-3/4” BOLT (57), two 3/8 X 1” SPACERS (51) and one 3/8” LOCK NUT (63). See FIGURE 13. FIGURE 14 • IMPORTANT! Uncoil and straighten all CABLES in order to remove all twist prior to installation STEP 14: • Assemble the WEIGHT STACK PIN (27) to the WEIGHT STACK SHAFT (26) as shown in FIGURE 14. • Screw the long threaded end of the WEIGHT STACK CABLE (29) into the end of the WEIGHT PLATE SHAFT (26) .See FIGURE 14. 3/8 X 1-3/4” 53 29 • Route the WEIGHT STACK CABLE (29) around the pulleys in the BOOM PLATES (14 & 15) as shown in FIGURE 14. (NOTE: Make sure the cable runs in the grooves of the pulleys.) • Assemble two PULLEY PLATES (10) around one 3-1/2” PULLEY (37) using one 3/8 X 1-3/4” BOLT (53) and one 3/8” LOCK NUT (63) as shown in FIGURE 14. (Note: Loop the CABLE around the PULLEY prior to assembling the PULLEY PLATES.) 63 37 10 26 27 13 FIGURE 15 3/8 X 4-1/4” 68 37 51 2 29 69 70 63 71 SHORT CABLE STEP 15: • Assemble one 3-1/2” PULLEY (37) to the BOOM PLATES (14 & 15) using one 3/8 X 4-1/4” BOLT (68), two 3/8” SAE WASHERS (69), two GUIDE CABLES (71), two 3/8 X 1” SPACERS (51) and one 3/8” LOCK NUT (63). See FIGURE 15.(Note: Loop the WEIGHT STACK CABLE around the PULLEY prior to assembling to the BOOM PLATES.) • Screw the short threaded end of the WEIGHT STACK CABLE (29) into the end of the PULLEY BRACKET (9) .See FIGURE 15. • Disassemble the SHORT CABLE and the turnbuckle on the GUIDE CABLE (71) as shown in FIGURE 15. The SHORT CABLE will be reassembled later. 14 39 14 3/8 X 2-3/4” 55 12 56 63 15 32 63 37 3/8 X 1-3/4” 53 9 FIGURE 16 STEP 16: • Route the BOOM CABLE (32) over the V-GROOVE PULLEY (39) and the 3-1/2” PULLEY (37) on the LEFT BOOM PLATE (15) and over the 3-1/2” PULLEY (37) on the RIGHT BOOM PLATE (14) and over the V-GROOVE PULLEY (39) as shown in STEP 16. • SECURELY assemble two 2” NYLON SPACERS (56) to the V-PULLEY PLATES (12) and the BOOM PLATES (14 & 15) using two 3/8 X 2-3/4” BOLTS (55) and two 3/8” LOCK NUTS (63). See FIGURE 15. • Assemble one 3-1/2” PULLEY (37) to the PULLEY BRACKET (9) using one 3/8 X 1-3/4” BOLT (53) and one 3/8” LOCK NUT (63) (Note: Loop the BOOM CABLE around the PULLEY prior to assembling the PULLEY BRACKET.) 15 70 71 SHORT CABLE FIGURE 17 STEP 17: • CAREFULLY slide the GUIDE BRACKET (70) through the GUIDE CABLES (71) as shown in FIGURE 17. • Assemble the SHORT CABLE and the turnbuckle to each GUIDE CABLE (71) as shown in FIGURE 17. • Adjust the turnbuckle on each GUIDE CABLE (71) to add tension to the GUIDE CABLES (71) until they are taut. Secure turnbuckle with the JAM NUTS as shown in FIGURE 17. 1/2 0 1/2 1 1/2 2 1/2 3 16 1/2 4 1/2 5 6 FIGURE 18 3/8 X 4-1/4” 68 51 37 8 71 3/8 X 3” 67 69 11 2 3/8 X 3-3/4” 57 49 63 64 37 30 63 STEP 18: • Securely assemble the ball end of the LEG CABLE (30) and one 3-1/2” PULLEY (37) to the LEG PEDESTAL (8) using two 3/8 X 3-3/4” BOLTS (57), two 3/8” X 1-1/16” FLANGE SPACERS (49), two 3/8” WASHERS (64), and two 3/8” LOCKNUTS (63). (NOTE: The LEG CABLE (91) must be routed over the retaining bolt as shown in FIGURE 18.) • Securely assemble one 3-1/2” PULLEY (37) to the UPRIGHT (2) using one 3/8 X 3” BOLT (67) and one 3/8” LOCKNUT (63). (NOTE: The LEG CABLE (91) must be routed over the retaining bolt as shown in FIGURE 18.) • Assemble one 3-1/2” PULLEY (37) to the BASE PLATES (11) using one 3/8 X 4-1/4” BOLT (68), two 3/8” SAE WASHERS (69), two GUIDE CABLES (71), two 3/8 X 1” SPACERS (51) and one 3/8” LOCK NUT (63). See FIGURE 18.(Note: Loop the LEG CABLE (30) around the PULLEY prior to assembling the PULLEY to the BASE PLATES.) 17 STEP 19: • FIGURE 19 Assemble one 3-1/2” PULLEY (37) to the PULLEY PLATES (10) using one 3/8 X 13/4” BOLT (53) and one 3/8” LOCK NUT (63) as shown in FIGURE 19. (Note: Loop the CABLE around the PULLEY prior to assembling the PULLEY PLATES.) 3/8 X 1-3/4” 53 10 63 37 30 FIGURE 20 9 30 51 3/8 X 3-3/4” 57 37 11 63 STEP 20: • Assemble one 3-1/2” PULLEY (37) to the BASE PLATES (11) using one 3/8 X 3-3/4” BOLT (57), two 3/8 X 1” SPACERS (51) and one 3/8” LOCK NUT (63). See FIGURE 19.(Note: Loop the LEG CABLE (30) around the PULLEY prior to assembling the BASE PLATES.) • Screw the threaded end of the LEG CABLE (30) into the end of the PULLEY BRACKET (9). See FIGURE 20. 18 FIGURE 21 55 3/8 X 2-3/4” 63 5 7 56 3/8 X 2-3/4” 55 63 38 4-1/2” 31 50 39 STEP 21: • Route the ARM CABLE (31) through the LEFT ARM (7) as shown in FIGURE 21. • Assemble one V-PULLEY (39) to the LEFT ARM SUPPORT (5) using one 3/8 X 2-3/4” BOLT (55) and one 3/8” LOCK NUT (63). See FIGURE 21. (Note: Loop the ARM CABLE around the PULLEY prior to assembling the LEFT ARM SUPPORT.) • SECURELY assemble one 2” NYLON SPACER (56) to the LEFT ARM SUPPORT (5) using one 3/8 X 2-3/4” BOLT (55) and one 3/8” LOCK NUT (63). See FIGURE 21. • Assemble the LEFT ARM (7) to the LEFT ARM SUPPORT (5) using one 3/8 X 2-3/4” BOLT (55) and one 3/8” LOCK NUT (63). See FIGURE 21. (Note: Make sure the ARM CABLE runs in FRONT of the bolt as shown!.) • Assemble one 4-1/2” PULLEY (38) to the LEFT ARM (7) using one 3/8 X 2-3/4” BOLT (55), two 3/8 X 1/2” SPACERS (50) and one 3/8” LOCK NUT (63). See FIGURE 21. (Note: Loop the ARM CABLE around the PULLEY prior to assembling the LEFT ARM.) 19 FIGURE 22 LOOP CABLE 3/8 X 3-3/4” 57 31 37 51 11 63 STEP 22: • Assemble two 3-1/2” PULLEYS (37) to the BASE PLATES (11) using two 3/8 X 3-3/4” BOLTS (57), one 3/8 X 1” SPACER (51) and two 3/8” LOCK NUTS (63). See FIGURE 22.(Note: Loop the ARM CABLE (31) around the PULLEYS prior to assembling the PULLEYS. Leave a loop in the ARM CURL as shown!) 63 FIGURE 23 9 3/8 X 1-3/4” 53 37 31 STEP 23: • Assemble one 3-1/2” PULLEY (37) to the PULLEY BRACKET (9) using one 3/8 X 1-3/4” BOLT (53) and one 3/8” LOCK NUT (63) (Note: Loop the ARM CABLE (31) around the PULLEY prior to assembling the PULLEY BRACKET.) 20 FIGURE 24 3/8 X 2-3/4” 55 56 4 31 6 63 39 50 4-1/2” 38 3/8 X 2-3/4” 55 STEP 24: • Route the ARM CABLE (31) through the RIGHT ARM (6) as shown in FIGURE 24. • Assemble one 4-1/2” PULLEY (38) to the RIGHT ARM (6) using one 3/8 X 2-3/4” BOLT (55), two 3/8 X 1/2” SPACERS (50) and one 3/8” LOCK NUT (63). See FIGURE 24. (Note: Loop the ARM CABLE around the PULLEY prior to assembling the RIGHT ARM.) • Assemble one V-PULLEY (39) to the RIGHT ARM SUPPORT (4) using using one 3/8 X 2-3/4” BOLT (55) and one 3/8” LOCK NUT (63). See FIGURE 24. (Note: Loop the ARM CABLE around the PULLEY prior to assembling the RIGHT ARM SUPPORT.) • SECURELY assemble one 2” NYLON SPACER (56) to the RIGHT ARM SUPPORT (4) using one 3/8 X 2-3/4” BOLT (55) and one 3/8” LOCK NUT (63). See FIGURE 24. • Assemble the RIGHT ARM (6) to the RIGHT ARM SUPPORT (4) using one 3/8 X 2-3/4” BOLT (55) and one 3/8” LOCK NUT (63). See FIGURE 24. (Note: Make sure the ARM CABLE runs in FRONT of the bolt as shown!.) 21 TIGHTEN! TIGHTEN! TIGHTEN! TIGHTEN! TIGHTEN! TIGHTEN! FIGURE 25 STEP 25: • SECURELY tighten all loose frame connections as shown in FIGURE 25! 1/2 0 1/2 1 1/2 2 1/2 3 22 1/2 4 1/2 5 6 FIGURE 26 16 64 55 3/8 X 2-3/4” 2 STEP 26: • SECURELY assemble one SEAT PAD (16) to the UPRIGHT (2) using two 3/8 X 2-3/4” BOLTS (55) and two 3/8” WASHERS (64). See FIGURE 26. FIGURE 27 52 2 3 8 17 44 45 STEP 27: • Assemble two ROLLER PADS (17) to the LEG PEDESTAL (8) using one 3/4 X 17” TUBE (52) and two 3/4” STARLOCK COLLARS (44) as shown in FIGURE 27. • Assemble two ROLLER PADS (17) to the SEAT ADJUST (3) using one 3/4 X 1” TUBE (52), two PLASTIC WASHERS (45) and two 3/4” STARLOCK COLLARS (44) as shown in FIGURE 27. • Assemble two ROLLER PADS (17) to the UPRIGHT (2) using one 3/4 X 17” TUBE (52) and two 3/4” STARLOCK COLLARS (44) as shown in FIGURE 27. 23 FIGURE 28 32 41 20 31 41 19 35 59 41 30 STEP 28: • Assemble two 14-1/2” SEWN HANDLES (19) to the ARM CABLE (31) using two SNAP LINKS (41) as shown in FIGURE 28. • Assemble two 7-1/2” SEWN HANDLES (20) to the BOOM CABLE (32) using two SNAP LINKS (41) as shown in FIGURE 28. • Assemble the ANKLE STRAP (35) to the LEG CABLE (30) using two SNAP LINKS (41) and one 12-LINK CHAIN (59) as shown in FIGURE 28. 24 ADJUSTMENT 9 ADJUSTMENT 23 9 ADJUSTMENT TURNBUCKLE JAM NUT FIGURE 29 STEP 29: • Adjustments can be made in the above locations to set the correct amount of tension in the cables. • Adjust the turnbuckle on each GUIDE CABLE (71) to add tension to the GUIDE CABLES (71). Secure turnbuckle with the JAM NUTS as shown in FIGURE 29. • If upon completion of assembly, the HEAD PLATE (23) does not sit on top of the first WEIGHT PLATE (21), push the HEAD PLATE (23) down, insert the WEIGHT STACK PIN (27) and perform several repetitions. This will relax the cable system and prevent the HEAD PLATE (23) from lifting up. See FIGURE 29 • If after completing the previous step, the HEAD PLATE (23) still does not sit on top of the first WEIGHT PLATE (21) or if there is excess slack in the cable system, adjust the threaded ends of the CABLES attached to the PULLEY BRACKETS (9) accordingly and retighten the jam nuts. See figure 29. • For maximum performance, the HEAD PLATE (23) should just barely sit on the top WEIGHT PLATE (21). • NOTE: After making adjustments make sure all jam nuts are SECURELY TIGHTENED! • This completes the assembly of the 777 Gym System. If the 777 SHROUD OPTION was purchased refer to the 777 SHROUD KIT assembly instructions. Thank you for purchasing the ParaBody 777 Gym System. If unsure of proper use of equipment, call your local ParaBody distributor or call the ParaBody customer service department at (800) 328-9714 25 MAINTENANCE Please note: * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your ParaBody customer service representative at (800) 328-9714. * Inspect equipment daily. Tighten all loose connections are replace worn parts immediately. Failure to do so may result in serious injury * Lubricate guide rods with a teflon based (or equivalent) lubricant on a regular basis * PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION. REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND MAIL BACK. MODEL #________________________ SERIAL #_________________________ DATE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ Thank you for purchasing the ParaBody 777 Gym System. 26 LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product. 2. LIMITED WARRANTY ON PARTS. If the following parts are defective in material or workmanship, ParaBody will supply replacement parts: all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retaining clips, adjustable pre-stretch slides, roller pad shafts, allen head bolts, weight selector pin, weight stack shaft, set screws, protector caps, adjustment chain, cotter pin, plunger, spring and knob. Terms: Lifetime – for so long as the Customer owns the ParaBody product. 3. LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in material or workmanship, ParaBody will repair or replace them, at its option. Terms: Three (3) years. 4. CONDITIONS AND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person other than an authorized ParaBody Service Center, any improper assembly, accident, or any other condition resulting from occurrences beyond the control of ParaBody will void this Limited Warranty. 5. REPLACEMENT AND REPAIR EXPENSES. ParaBody will provide only replacement parts or repair under this warranty. The Owner is responsible for all other costs. Such costs may include, but are not limited to: a. labor charges for service, removal, repair or reinstallation of the ParaBody product or any component part; b. shipping, delivery, handling and administrative charges for returning parts to ParaBody; and c. all necessary or incidental costs related to installation of the replacement parts. 6. SHIPPING. If shipping by the Owners is deemed necessary (in sole discretion of ParaBody), parts should be shipped in their original carton or equivalent packaging, fully insured with shipping charges prepaid. ParaBody will not assume any responsibility for any loss or damage incurred in shipping. 7. CLAIM PROCEDURES. If service on your ParaBody product is required during the warranty period, please contact our Customer Service Department at 1-800-328-9714 for instructions regarding returning or replacing parts. Please have available the following information: (i) the dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product (the serial number location is called out on the final assembly drawing included with your assembly instruction); (iv) a description of the nature of the problem. 8. OWNER’S RIGHT. This Limited Warranty gives you specific legal rights. You may also have other rights, which vary depending on local law. 9. LIMITATION OF IMPLIED WARRANTIES. All implied warranties, except to the extent prohibited by applicable law, shall have no greater duration than the warranty period set forth above. There are no warranties which extend beyond the description in this Limited Warranty. Because local laws do not allow limitations on how long an implied warranty lasts, the above limitations may not apply to you. 10. DISCLAIMER. No other express warranty has been made or will be made on behalf of ParaBody with respect to any ParaBody product or the operation, repair or replacement of any ParaBody product. ParaBody shall not be responsible for injury, loss of use of the ParaBody product, inconvenience, loss or damage to personal property, whether direct or indirect, and incidental or consequential damages, so the above limitation or exclusion may not apply to you. NOTES: 27 LIFE FITNESS CONSUMER DIVISION 14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A. Tel: 763.323.4500 Fax: 763.323.4797 800.328.9714 (Toll-free within the U.S. and Canada) www.parabody.com INTERNATIONAL OFFICES Life Fitness Atlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 Life Fitness (UK) Ltd. Queen Adelaide Ely, Cambs CB7 4UB United Kingdom Phone CSS: (01353) 665507 Fax CSS: (01353) 666719 Life Fitness EUROPE GmbH Siemensstrasse 3 85716 Unterschleissheim Germany Phone: (089) 31 77 51-0 Fax: (089) 31 77 51 99 Life Fitness Benelux N.V. Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: 31 (180) 64 66 69 Fax: 31 (180) 64 66 99 Life Fitness Italia S.R.L. Via Elvas 92 39042 Bressanone Italy Phone: 39 (472) 835-470 Fax: 39 (472) 833-150 Life Fitness Japan 8/F, Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, Tokyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 Life Fitness Do Brazil Al. Rio Negro, 433-Predio 2-Sala 2 3º andar (Confab) Aplhaville-Barueri-Sao Paulo CEP: 06454-904 Brazil Phone: 55 (11)7295-2217 Fax: 55 (11) 7295-2218 Life Fitness Asia Pacific Limited Room 2610, Miramar Tower 132 Nathan Road, Tsimshatsui Kowloon, Hong Kong Phone: (852) 2891-6677 Fax: (852) 2575-6001 28
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2002:01:08 14:02:59Z Subject : 777102-bk1a Modify Date : 2004:12:10 15:27:07-06:00 Page Count : 28 Creation Date : 2002:01:08 14:02:59Z Producer : Acrobat Distiller 4.05 for Windows Author : moravem Keywords : Mod Date : 2004:12:10 15:27:07-06:00 Metadata Date : 2004:12:10 15:27:07-06:00 Description : 777102-bk1a Title : 777102-bk1a Creator : moravemEXIF Metadata provided by EXIF.tools