Parabody 843102 Assembly Instruction
843102 to the manual 785836df-8ad5-485f-b2be-708a7aab726c
2014-12-13
: Parabody Parabody-843102-Assembly-Instruction-125626 parabody-843102-assembly-instruction-125626 parabody pdf
Open the PDF directly: View PDF 
.
Page Count: 7
| Download | |
| Open PDF In Browser | View PDF |
I I 843102 I I POWER RACK ASSEMBLY INSTRUCTIONS III Part # 6757501 I II I II II 1 I Revision: 5/06/98 NOTES !] ,Ily~, ORTANT W~LCOM~ TOWOP.LD OF$’eKm~~ $’ted./ Please note: * Thank you for purchasing the Parabody 843102 POWER RACK.Please read these instructions thoroughlyand keep themfor future reference. This product must be assembledon’a fiat, level surface to assure its proper function. * Werecommend cleaning your product (pads and frame) on a regular basis, using warmsoapy water. Touch-uppaint can be purchased from your Parabodycustomer service representative at (800) 328-9714. Thereis a risk assumedby individuals whouse this type of equipment.To minimizerisk, please follow these rules: 1. Inspect equipmentdaily. Tighten all loose connections and replace woruparts immediately. Failure to do so mayresult in serious injury. 2. Donot allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. If unsure of proper use of equipment,call your local Parabodydistributor or call the Parabodycustomer service department at (800) 328-9714. 5. Consult a physician before beginning any exercise program. Tools Required for Assembly * 3/4" wrench * Ratchet with 3/4" and 9/16" sockets * Rubber Mallet or Hammer Length ~Ruler Bolt’ ......... NOTE: BOLT LENGTH IS 1V[EASURED FROM THE UNDERSIDE OF TFI-E HEAD OF THE BOLT. BOLT LENGTH BOLT LENGTH RULER: 1/2 0[ 1 I 2 1/2 I 3 1/2 I 4 1/2 1 5 1/2 "I 6 PARTS LIST PART# 6641503 6641802 6605702 6605802 6605902 6606002 6606102 3102910 DESCRIPTION UPRIGHT QTY 2 KEY PART# 9 2 SA~T~L BAR sUPPORT CHIN BAR ’ ’LOWER CONNECTOR UPPER CON~CTOR " ’ 2 12 1 15 3102917 3102502 3102801 6606801 6405201 6467001 6590801 DESCRIPTION ’ i/2~4"BOLT 1/2" WASHER I~’iLOCKNUT SPRING PIN ASSEMBLY ’ 2"SQ. ENDCAP 2" SQ. COVERCAP " ’ 3 X 2" INSERT GUIDE 1/2X3"BOLr FIGURE 1 STEP 1: ¯ Slide four 2" SQ. COVER CAPS(14) over the ends of each UPRIGHT BASE(2) as shown in F]:GURE ¯ LOOSELY assemble the LOWER CONNECTOR (6) between each UPRIGHT BASE(2) using four 1/2 X 3" BOLTS(8), four WASHERS (10), and four 1/2" LOCKNUTS( l 1). See FIGURE 3 QTY 4 20 -14 6 ’4 4 FIGURE 2 STEP 2: Insert tweJve 3 X 2"/NSERTGUH3ES (15) into the ends of each SAFETy/LML ,2. (NOTE:Makesure the INSERT GUIDES (I5) snap into the holes of the weldments.)(3) and BAR SUPPORT FIGUR~ SECURELY assemble the six SPRINGPIN ASSEIVIBLI~S(12) to the each BAR SUPPOKT(4) as shown in FIGURE2. SPRING PIN BARRELSon each SAFETYRA./L FIGURE 3 STEP 3 ¯ Insert four 2" SQ. ENDCAPS(13) into the ends of the UPRIGHTS (1) as shown in FIGURE ¯ Slide one BARSUPPORT (4) and one SAFETYRAIL (3) (iN THATORDER)onto each UPRIGHT (1). Pull back SPRINGPIN ASSEMBLIES until they pop into holes. 5 FIGURE 4 STEP4: --’~ ¯ LOOSELY assemble each UPRIGHT (1) to the UPRIGHT BASE(2) using four 1/2 X 4" BOLTS (91, eight 1/2" WASHERS and four 1/2" LOCK NUTS (1 1). See FIGURE ¯ LOOSELY assemble the UPPER CONNECTOP, (7) using four 1/2 3"BOL TS (8), fou r 1/2 " WAS HEP, S (10), and two LOCKNUTS(11). See FIGURE 4 6 5 I 6 STEP5: ¯ LOOSELY assemble the CHINBAR.(5) using four 1/2 X 3" BOLTS (8), four I/2" WASHERS (10), and four i/T’ LOCK (11). See FIGURE Whenall componentsare assembled, SECURELY tighten all bolt connections. THIS CONCLUDESTHE ASSEMBLYOF THE 843102 PO’WER RACK.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Creator : ExperVision Producer : TypeReader 6.0 Professional Page Count : 7 Page Mode : UseThumbsEXIF Metadata provided by EXIF.tools