Parabody Leg Press 100101 Assembly Instruction

100101 to the manual 9bac53c1-4440-47ce-a42a-f80ed5067533

2014-12-13

: Parabody Parabody-Leg-Press-100101-Assembly-Instruction-125656 parabody-leg-press-100101-assembly-instruction-125656 parabody pdf

Open the PDF directly: View PDF PDF.
Page Count: 14

DownloadParabody Parabody-Leg-Press-100101-Assembly-Instruction-  Parabody-leg-press-100101-assembly-instruction
Open PDF In BrowserView PDF
1001 O1 LEG PRESS

WARNING:
Read and follow all directions
for each step to insure proper
assemblyof thi,,; product.

ASSEMBLY INSTRUCTIONS
Part # 7037301
Rev. A

1

Revision: 12/4/00

]IMPORTANT NOTES]
Please note:
* Thankyou for purchasing the Parabody100101LEGPRESS.Please read these instructions
thoroughly and keep themfor future reference. This product must be assembledon a flat,
level surface to assure its proper function.
Werecommend
cleaning your product (pads and flame) on a regular basis, using warmsoapy
water. Touch-uppaint can be purchased flom your Parabodycustomer service representative
at (800) 328-9714.
There is a risk assumedby individuals whouse this type of equipment.To minirnize risk, please
follow these rules:
1. Inspect equipmentdaily. Tighten all loose connectionsand replace wornp~:ts immediately.
Failure to do so mayresult in serious injury.
2. Donot allow minors or children to play on or aroundthis equipment.
3. Exercisewith care to avoid injury.
4. If unsureof proper use of equipment,call your local Parabodydistributor or call the
Parabodycustomer service department at (800) 328-9714.
5. Consult a physician before beginningany exercise program.

[ Tools Required for Assembly]
* 3/4" wrench
* 9/16" wrench
* Ratchet with 3/4" and 9/16" sockets
* Adjustable wrench
* 5/32" Mien wrench
* Tape measure

Bolt Length Ruler
NOTE: BOLT LENGTH IS

MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.

BOLT LENGTH

I

BOLT LENGTH RULER:
I

1/2

]

1/2

]

2

1/2

]

3

2

1/2

[

4

1/2

]

1/2

5

]

6

PARTS LIST
!KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17

PART #
6574508
6573608
6575008
6575408
6573908
6476408
6575102
6597421
6574001
3103102
3116201
6177001
6405201
6416601
6467001
6500601
3102501

DESCRIPTION
BASE FRAME
SEATFRAME
REAR TUBE
FOOT PLATE
LEVER TUBE
HANDLE
ADJUSTMENT TUBE
SEAT PAD
3/4 X 8-1/4" SHAFT
1X8" GRIP
3-1/2" PULLEY
2-1/2 X 5-1/2" NON-SKID
STRIP
2" SQ. ENDCAP
PARAGLIDE
(QTY. 8)
2" SQ. COVERCAP
2" WHEEL
3/8" FLAT WASHER

QTY
1
,1
1
1
2
1
1
2
2
2
1
8
14
1
2
2
8

KEY PART #
18 3102601
19 3102802
20
3102807
21
3102801
22
3102804
23
3102941
24
3102922
25
3102904
26
3102935
27
3102918
28
3202107
29
6122703
30
6020601
31
3104901
32
3106803
33
6412001

3

DESCRIP 3N
3/8" LOCK WASHER
3/8" LOC) NUT
3/8" LOWHEIGH’ LOCK NUT
1/2" LOCI{ NUT
1/2" LOWHEIGHT LOCK NUT
3/8 X 1-1/2" BOLT
3/8 X 2-3/4" BOLT
3/8 X 3" BOLT
3/8 X 4-1/2" BOLT
1/2 X 3-1/4" BOLT
1/2 X 6-1/2" BOLT
3/8 ID X 3/8" SPACER
1/2" FLANGEBEARING
3/4" FLANGEBEARING
5/16" SET SCREW
3/8" SPRIN~3 PIN

QT¥
4
2
1
2
2
2
2
2
1
2
2
2
8
4
4
1

3/8

FIGURE 1
STEP1:
¯ Attach two 2" SQ. COVER
CAPS(15) onto the ends &the REARTUBE(3) as shown in FIGURE
¯ Insert four 2" SQ. ENDCAPS
(13) into the ends of the BASEFRAME
(1) as shown in FIGURE
SECURELY
assemble the REARTUBE(3) to the BASEFRAME
(1) using two 3/8 X 3" BOLTS(25), 278" FLAT WASHE
RS
(17), and two 3/8" LOCKNUTS(19). See FIGURE
]
0

1/2

I
1

1/2

I
2

1/2

[
3
4

I/2

[
4

1/2

[
5

1/:!

I
6

I
/

/

FIGURE 2
STEP2:
¯ Insert two 2" SQ. ENDCAPS
(13) into file ends of the SEATFRAME
(2) as shown in FIGURE
¯ SECURELY
assemble one 3/8" SPRINGPIN (33) to the spring pin barrel on the SEATFRAME
(2) as shown in FIGURE
¯ Attach four PARAGLIDE
STRIPS(14) to the inside of the SEATFRA~£E
(2) using file following steps:
¯

Thoroughly clean all surfaces where the PARAGLIDE
STRIPS(14) are to be attached.

¯

l~emovethe PARAGLIDE
STRIPS(14) from the paper backing and firmly apply them to all shownsurfaces.

5

3/8"

LOWHEIGHT

/

FIGURE 3
STEP 3:
¯ SECURELY
assemble one 3-1/2" PULLEY
(11), two 2" WHEELS
(16), two 3/8" FLATWASHERS
(17):. and two 3/8 ID
SPACERS
(29) to the ADJUSTMENT
TUBE(7) using one 3/8 X 4-1/2" BOLT(26) as shown in FIGURE
¯ Attach four PARAGLIDE
STRIPS(14) to the outside of the ADJUSTMENT
TUBE(7) using the followirtg

steps:

¯

Thoroughly clean all surfaces where the PARAGLtDE
STRIPS(14) are to be attached.

¯

Removethe PARAGLIDE
STRIPS(t4) from the paper backing and firmly apply them to all shownsurfaces.

1/2

I

1/2

I

1/2

I
3

1/2

I
4

1/2

I
5

1/2

I
6

PIN

FIGURE 4
STEP 4:
¯ CAREFULLE¥
slide the ADJUSTMENT
TUBE(7) over into the SEATFRAME
(2) and engage the SPRINGPIN into one
the adjustmentholes. See FIGURE
4.
STEP 5:
¯ Insert two 3/4" FLANGE
BEARINGS
into
each of the two LEVER
TUBES
(5)
shownin FIGURE
5.

FIGURE 5

5/16"

SET

SCREW~

FIGURE 6
STEP 6:
¯ Insert four 2" SQ. ENDCAPS
(13) into the ends of two LEVER
TUBES
(5) as shownin FIGURE
assemble the LEVER
TUBES
(5) to the BASEFRAME
(1) using two 3/4" SHAFTS
(9) and. SECURE
in
¯ SECURELY
using four 5/16" SETSCREWS
(32). See FIGURE

1/2

I

1/2

I

2

1/2

I

1/2

I

I I

[

4
I

1/2

I

6

FIGURE 7
STEP7:
¯ Insert four 2" SQ.END
CAPS
(13) into the ends of FOOT
PLATE
(4) as shownin FIGURE
¯ Insert eight 1/2" FLANGE
BEARING
(30) into the LEVER
TUBES
(5) as shownin FIGURE

1/2"

LOW HEIGHT @~’""

FIGURE 8
STEP8:
¯ SECURELY
assemble the FOOTPLATE(4) to the LEVERTUBES(5) using two 1/2 X 6-1/2" BOLTS(28) and two 1/2"
HEIGHTLOCKNUTS(22) as shown in FIGURE
¯ CAREFULLY
attach eight NON-SKIDSTRIPS (12) to the FOOTPLATE(4) as shown in FIGURE

3-1/4"

FIGURE 9
STEP 9:
¯ SECURELY
assemble the SEATFRAME
(2) to the LEVERTUBES(5) using two 1/2 X 3-1/4" BOLTS(27) and two 1/2"
NUTS(21) as shown in FIGURE

11

/
/
!
I
I
/
/
/
I
I

~

I
I
I
I
I
I
i
I
I
I
I

/
/
/
I

I
I

I
I
/
/
1

~
3/8

I
/
/
/

X 1-1/2"~

FIGURE 10
STEP10:
¯ SECURELY
assemble the SEATPAD(8) to the HANDLE
(6) and the SEATFRAME
(2) using two 3/8 X 1-1/2" BOLTS
two 3/8" LOCKWASHERS
(18), and two 3/8" FLATWASHERS
(17). See FIGURE

1/2

112

[

1
] I 1

I

1/2

[

2

I I 1

[

1/2

6

I

[

I

I I
12

X 2-3/4~/

FIGURE 11
STEP 11:
¯ SECURELY
assemble the SEATPAD(8) to the SEATFRAME
(2) using two 3/8 X 2-3/4" BOLTS(24) and two 3/8"
WASHERS
(18) as shown in FIGURE11.
¯ Slide two 1 X 8" GRIPS(10) over each HANDLE
(6) as shown in FIGURE
13

FIGURE 12
STEP 12:
¯ To adjust the SEAT,sit in the LEGPRESS,gently press against the FOOT
PLATE
and pull back on the SPRING
PiN.
¯ Refer to the LEGPRESSADAPTOR
assemblyinstructions to attach the 832102LEGPRESSto the homegym.
Thank you for purchasing the Parabody 100101 LEGPRESS. If unsure of proper use of equipment, call
your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
I

0
I

1/2

I I

112

I

1
1 I

I

I

1/2

I

2
I I

I

I

1/2

I

I

3
I

<14

I

1/2

I

3;/2

I

6
I

I

I

I

I



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Creator                         : ExperVision
Producer                        : TypeReader 6.0 Professional
Page Count                      : 14
Page Mode                       : UseThumbs
EXIF Metadata provided by EXIF.tools

Navigation menu