Paradox Security Systems MG5050V2 Wireless control panel board User Manual MGSP EI16
Paradox Security Systems Wireless control panel board MGSP EI16
UserManual.wiki
>
Paradox Security Systems
>
MG5050V2 User Manual
Users Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![Magellan 1Part 1: Introduction1.1 Features• 32 zones (any of which can be wireless or keypad zones).• 32 users and 32 remote controls (one per user).• In-field upgrades: Update the panel’s firmware by connecting it to a PC via a 307USB Interface and then using the Winload software (V2.80 or higher). • Menu-driven programming for the Installer, Master, and Maintenance codes. This enables you to program the panel through a simple and easy to use interface, without the use of section numbers. • Multiple telephone numbers for event reporting: Three for the monitoring station, five for personal dialling and one for pager reporting. Up to five persons can now be contacted by the panel in case of alarm. • Calendar with daylight savings time (enable section [730], option [1] and choose section [731] to put in the Country Code): You can now select 1 out of 18 different country groups each with its own pre-programmed local daylight savings time. You can also customize the daylight saving time by programming sections [732] and [733].• New Sleep arming method: Similar to Stay arming, Sleep arming allows users to remain in a protected area, but provides a higher level of protection. For example, in a two-story house, the perimeter is protected with Stay arming. With Sleep arming, the perimeter as well as the main floor is protected (motion detectors, etc.), allowing you to roam the second floor and sleeping quarters.• Connect up to 15 hardwire keypads on the 4-wire communication bus.• Push button power reset: Convenient reset button saves time when a momentary powerdown is required as opposed to having to physically disconnect the control panel’s power cables. Press and hold the RESET switch for five seconds. The STATUS LED will start flashing. Within 2 seconds of this flashing, press the reset switch again. The panel will reset to default and restart. Also, you can reset all programmable sections to factory default values in section [950].• Available in 433MHz or 868MHz.• Supports Memory Key (PMC-4 and PMC5).• RF jamming supervision (section [700], option [5]): The control panel will report a trouble if the RF signal is being jammed.• Supports SIA reporting format to central station.1.2 System Overview1.3 Modules Current Consumption List Module Description Maximum number per systemK32RF 32-Zone Wireless LED Keypad Module 8K10V/H, K32, K32+,K32LCD, K32LCD+, K32LX, K35, K636, TM5010 and 32-Zone Hardwired LED and LCD Keypad Module, Touchscreen15 total including ZX8ZX8 ZX8SP 8-Zone Expansion Module 3RPT1 Magellan Wireless Repeater Module 2VDMP3 Plug-In Voice Dialer 1IP100 or IP150 IP Internet Module 1RTX3 Wireless Expansion Module (Spectra SP only) 1PCS250 or PCS250G GSM/GPRS Communicator Module 1RX1 Wireless Receiver Module 1PGM4 4 output Expansion Module 1HUB2 2-Port HUB and Bus Isolator 1Module Current Consumption Module Current ConsumptionK10V/H Min. = 44mA / Max. = 72mA IP150 100mAK32 Min. = 49mA / Max. = 148mA TM50 Standby:100mA / Alarm: 200mAK32 + Min. = 49mA / Max. = 148mA PCS250 Standby:100mA / Alarm: 450mAK32LCD Min. = 43mA / Max. = 86mA PCS250G Standby:100mA / Alarm: 450mAK32LCD + Min. = 43mA / Max. = 86mA RX1 25mAK32RF Min. = 48mA / Max. = 130mA PGM4 Min. = 13mA / Max. = 150mAK35 Min. = 30mA / Max. = 70mA HUB2 Min. = 24mA / Max. = 50mAZX8 Min. = 29mA / Max. = 31mA K636 Min. = 15mA / Max. = 30mARTX3 Min. = 61mA / Max. = 143mAVDMP3 Min. = 28mA / Max. = 28mAK32LX 120mA](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-5.png)
![4 Reference & Installation Manual 2.6 MG5050 / MG5050 EN PCB LayoutUsed for In-Field Firmware upgrade through a 307USB Direct Connect Interface. See Connecting to WinLoad on page 51 for details.AntennaDo not cut, bend or alter the antennas and ensure that electrical wires do not cross over the antennae, as this may affect signal reception.Four pin connector can be used for quick installation of a MG5050 keypad.Refer to AC Power & Backup Battery Connections on page 3.Charge LED:Charging and battery test LEDStatus LED: • Flash once every second = Normal•Flashes ON 1 second and OFF 1 second = Any trouble • Always ON = Panel is using phone line • Fast flash 6 seconds after power up = Installer lock enabled "RX" & “TX” LED:Flashes quickly when receiving or transmitting RF signals from wireless devices.To metallic enclosureGround clampAWG#14 single conductor solid copper wireCold water pipe groundingThe "BELL" output will shutdown if the current exceeds 3A.Refer to Single Zone Inputs on page 6Max. amount of keypads = 15 keypadsMax. current = 700 mAMax. distance of keypad from panel = 76m (250 feet)Max. total run of wire = 230m (750 feet)BUS (RED BLK GRN YEL)Connect Paradox devices accordingly.This is a unique connection interface used for interconnection between Paradox devices.This equipment must be installed and maintained by qualified service personnel only.For UL and C-UL warnings, refer to the UL and C-UL Warnings section at the back of the Reference & Installation Manual.Press and hold the RESET button for five seconds. The STATUS LED will start flashing. Within 2 seconds of this flashing, press the reset switch again. The panel will reset to default and restart.EBUS and Dialer used for VDMP3 plug-in voice module for voice reporting.PGM Trigger: This jumper allows you to choose whether the solid state relay PGM (PGM4 only) is grounded (-), or gives out 12V (+).For the keypad’s zone configurations, refer to the Installer Quick Menu. If EOL is enabled: see section [706] option [2]. Also refer to Single Zone Inputs on page 6.Disconnect telephone line before servicing.MG5050 EN 50131 Immunity to Attenuation TestWhen performing the attenuation test, replace antenna A with the following:• For a 433 MHz panel, use an antenna with a length of 10.2 cm (4 in.)• For a 868 MHz panel, use an antenna with a length of 6.1 cm (2.4 in.)Once the test is complete, reinsert the original antenna (A) in its place, and connect the wires (not shown) to a zone input programmed for tamper.Tamper antenna for EN 50131 compliancyTo provide maximum lightning protection we strongly recommend having separate earth connections for the dialer and zone ground terminals.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-8.png)
![8 Reference & Installation Manual Part 3: Programming Methods3.1 WinLoad Software for WindowsProgram the control panels remotely or on-site using the WinLoad Software (V2.80 or higher) for Windows®. For more information, contact your local Paradox Distributor or visit our web site at paradox.com. If you are using the WinLoad software, you must program the features (see Settings for WinLoad Software on page 51). Update the panel’s firmware by connecting it to a PC via a 307 Direct Connect Interface and then using the Winload software. (Not investigated by UL).3.2 Programming Using a KeypadUse the supplied programming guide to keep track of which sections were programmed and how. We recommend you read the entire manual before you begin programming. 3.2.1 Single Digit Data Entry Method (Decimal and Hexadecimal)Single Digit Data Entry is used in all sections except those specified in the Feature Select Programming Method (below). After entering Programming Mode as described in the shaded box above, some sections will require that you enter Decimal values from 000 to 255. Other sections will require that you enter Hexadecimal values from 0 to F. The required data will be clearly indicated in this manual as well as in the programming guide. When entering the final digit in a section, the control panel will automatically save and advance to the next section. Except sections 001 to 032, after entering the first three digits the control panel will switch to Feature Select Programming. For phone number programming, press [ENTER] to save the data. 3.2.2 Feature Select Programming MethodAfter entering certain sections, eight options will be displayed where each option from [1] to [8] represents a specific feature. Press the key corresponding to the desired option. This means the option is ON. Press the key again to remove the digit, thereby, turning OFF the option. When the options are set, press the [ENTER] key to save and advance to the next section.How Do I Enter Programming Mode?1) Press [ENTER]2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter 3-digit [SECTION] you wish to program4) Enter required [DATA] Table 2: Decimal and Hexadecimal Programming TableValue or Action What Do I Press?What Do I See?32-zone LED 10-zone LEDValue 0 / Replace Current Digit with 0[SLEEP]Erase digit and remain in section Erase digit and remain in sectionValues 1 to 9 [1] to [9] Zone 1 to 9 [1] to [9]A (hex only) [0] Zone 10 [0]B (hex only) [OFF]Zone 11 [OFF]C (hex only) [BYP]Zone 12 [BYP]D (hex only) [MEM]Zone 13 [MEM]E (hex only) [TBL] Zone 14 [TBL] F (hex only) [] Zone 15 [] Exit Without Saving [CLEAR]ARM & STAY LED flash ARM & STAY LED flashSave Data (hex only) [ENTER]Advances to the next section Advances to the next section](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-12.png)
![Magellan 93.2.3 Data Display Mode (except K32LCD and K32LCD+)In the Data Display Mode you can view the programmed contents of each section one digit at a time. Figure 5: Data Display Mode3.3 Configuring the Keypad Zone NumberPLEASE NOTE: After five minutes, the keypad exits programming mode.3.4 Programming Using A Paradox Memory Key*Copy the sections of one control panel into the Paradox Memory Key (PMC-4/PMC5). Then copy the contents of the Memory Key into as many control panels as needed. Each panel is programmed in less than 3 seconds.Download to DESTINATION Control Panel or module1) Remove AC and battery power from the control panel.2) Place the Memory Key on the serial connector labeled MEMORY KEY of the Control Panel that is to receive the contents of the Memory Key.3) Reapply AC and battery power. 4) In Installer Programming Mode, enter section [970], the keypad emits a confirmation beep. 5) When the keypad emits a second confirmation beep, remove the Memory Key.Copy to Memory Key from SOURCE Control Panel or module1) Remove AC and battery power from the control panel.2) Place Memory Key on the serial connector labeled MEMORY KEY of the Control Panel that you want to copy. Make sure the write protect jumper of the Memory Key is on.3) Reapply AC and battery power.4) In Installer Programming Mode, enter section [975]. The keypad emits a confirmation beep.5) After the keypad emits a second confirmation beep, remove the Memory Key. Remove the Memory Key’s jumper if you do not wish to accidentally overwrite its contents.* Not investigated by ULHow Do I Configure The Keypad?Press [ENTER]Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)Press [] and hold for three secondsEnter the desired zone number key (K32/K32+, K32LCD/K32LCD+: 2-digit entry 01 to 32, K10V/H: 1-digit entry 1 to 0(10)) Press [ENTER] to save and exit programming modePress [CLEAR] to erase data without savingPress [CLEAR]+[CLEAR] to exit programming mode without savingTo access the Data Display Mode, press the [ENTER] key after entering a section and before entering any data. The four LEDs as indicated below will begin to flash indicating that you are in the Data Display Mode.Each time the [ENTER] key is pressed, the keypad will display the next digit in the current section and will continue through all the following sections one digit at a time without changing the programmed values. Not available for sections using the Multiple Feature Select Method. Press the [CLEAR] key at any time to exit the Data Display Mode.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-13.png)
![Magellan 11Part 4: LCD Keypad Labels4.1 Input Keys4.2 Label Sections4.3 Special Characters and Keypad Letter AssignmentAlphanumeric Key Input[1] A / B / C[2] D / E / F[3] G / H / I[4] J / K / L[5] M / N / O[6] P / Q / R[7] S / T / U[8] V / W / X[9] Y / ZSpecial Function KeysKey Function[STAY]Insert space[SLEEP]Delete[ARM]Delete whole entry[OFF]Toggle numeric/alphanumeric keys[BYP]Toggle lower case/upper case[MEM]Special charactersLabel Sections[181] to [212]32 Zone Labels[341] to [356]16 PGM Labels[511] to [542]32 User Labels[771] to [772]2 Partition Labels[568] to [569]2 Wireless Labels[599] to [606]8 Wireless Keypads[781] to [795]15 Bus Modules LabelsPolish001 002 003 004 005 006 007Hungarian001 002 003Turkish001Special Character CataloguePolish / Hungarian / Turkish Special Character Catalogue](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-15.png)
![12 Reference & Installation Manual Hebrew Keypad Letter Assignment Hebrew Special Characters Catalogue032 048 064 080 096 112 160 176 192 208 224 240033 049 065 081 097 113 161 177 193 209 225 241034 050 066 082 098 114 162 178 194 210 226 242035 051 067 083 099 115 163 179 195 211 227 243036 052 068 084 100 116 164 180 196 212 228 244037 053 069 085 101 117 165 181 197 213 229 245038 054 070 086 102 118 166 182 198 214 230 246039 055 071 087 103 119 167 183 199 215 231 247040 056 072 088 104 120 168 184 200 216 232 248041 057 073 089 105 121 169 185 201 217 233 249042 058 074 090 106 122 170 186 202 218 234 250043 059 075 091 107 123 171 187 203 219 235 251044 060 076 092 108 124 172 188 204 220 236 252045 061 077 093 109 125 173 189 205 221 237 253046 062 078 094 110 126 174 190 206 222 238 254047 063 079 095 111 127 175 191 207 223 239 255Greek Keypad Letter AssignmentKey Press key oncePress key twicePress key three times[1] ABG[2] DEZ[3] HQ I[4] KLM[5] NO[6] PRS[7] TUF[8] CYWGreek Special Characters Catalogue016 032 048 064 080 096 112 128 144 160 176 192 208 224 240017 033 049 065 081 097 113 129 145 161 177 193 209 225 241018 034 050 066 082 098 114 130 146 162 178 194 210 226 242019 035 051 067 083 099 115 131 147 163 179 195 211 227 243020 036 052 068 084 100 116 132 148 164 180 196 212 228 244021 037 053 A069 085 101 117 133 149 165 181 197 213 229 245022 038 054 070 086 102 118 134 150 166 182 198 214 230 246023 039 055 071 087 103 119 135 151 167 183 199 215 231 247024 040 056 072 088 104 120 136 152 168 184 200 216 232 248025 041 057 073 089 105 121 137 153 169 185 201 217 233 249026 042 058 074 090 106 122 138 154 170 186 202 218 234 250027 043 059 075 091 107 123 139 155 171 187 203 219 235 251028 044 060 076 092 108 124 140 156 172 188 204 220 236 252029 045 061 077 093 109 125 141 157 173 189 205 221 237 253030 046 062 078 094 110 126 142 158 174 190 206 222 238 254031 047 063 079 095 111 127 143 159 175 191 207 223 239 255](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-16.png)
![14 Reference & Installation Manual Part 5: Access CodesThe control panel supports the following access codes:5.1 Access Code LengthSection [701]: System OptionsOption [1] OFF = 6-Digit Access Codes Option [1] ON = 4-Digit Access Codes (default)All access codes can be set to lengths of either 4- or 6-digits. When the 4-digit option is selected, entering a 4-digit code will allow access. Using the 6-digit option, entering 6 digits is required to allow access.If the access code length is changed from four digits to six digits when access codes have already been programmed, the control panel will automatically add the last 2 digits by using the first 2 digits. For example, if the access code is 1234 and you switch to 6 digits, the code will become 123412. Be sure to verify the access codes after switching from 4-digit access codes to 6-digit codes. When switching from six digits to four digits, the control panel will simply remove the final two digits of the access code. For example, 123456 will become 1234. 5.2 Installer Code (Default: 0000 / 000000) The Installer Code is used to enter the system‘s programming mode, which allows you to program all the features, options and commands of the control panel. The Installer Code can be 4- or 6-digits in length (see Access Code Length on page 14) where each digit can be any value from 0 to 9. The Installer Code cannot be used to program Master Code 1, Master Code 2 or user access codes. To program the Installer Code press:[ENTER]+ [CURRENT INSTALLER CODE] + [397] + new 4- or 6-digit Installer Code5.3 Maintenance Code (Default: Empty)The Maintenance code is similar to the Installer code. It can be used to enter programming mode, which allows you to program all the features, options and commands except for the system’s communication settings (sections [395], [397], [398], [815], [816], [817], [910], and [911]) as well as any user codes. The Maintenance code can be 4 or 6 digits in length where each digit can be any value from 0 to 9. The Maintenance code is empty by default. Set the Maintenance in section [398].[ENTER]+ [INSTALLER CODE] + [398] + new 4- or 6-digit Maintenance Code5.4 System Master Code (Default: 1234 / 123456)The Installer Code can be used to program the System Master Code. With the System Master Code a user can use any arming method and can program any user access code, but not the User Code Options. The System Master Code can be 4 or 6 digits in length, where each digit can be any digit from 0 to 9. The System Master Code can be modified but cannot be erased. To change the System Master Code press:[ENTER]+ [INSTALLER CODE] + [399] + new 4- or 6-digit System Master Code5.5 User Code OptionsSections [404] to [432]: Options [1] to [8]The User Code Options define which arming methods each user can use to arm or disarm the system. Regardless of these settings, all users can Regular arm assigned partitions and all users except those with the Arm Only option can disarm an assigned partition, regardless of how it is armed. Select one or more of the options described on the following pages for each user access code, where sections [404] to [432] represent user access codes 004 to 032. 5.5.1 Partition 1 AssignmentSections [404] to [432]: User codes 004 to 032Option [1] OFF = Deny access to partition 1 Option [1] ON = User code has access to partition 1 (default)Installer Code [397]: Used to program all control panel settings except user access codes.Maintenance Code [398]: The Maintenance code is similar to the Installer code. It can be used to enter programming mode, which allows you to program all the features, options and commands except for the panel’s communication settings. The maintenance code is empty by default.System Master Code [399]: Provides full access. Arm and disarm using any method described in the User Code Options below as well as program the user access codes.Master Code 1: Permanently assigned to partition 1. Same as a regular user code except it can also program access codes for user codes assigned to partition 1.Master Code 2: Permanently assigned to partition 2. Same as a regular user code except it can program access codes for user codes assigned to partition 2. If the system is not partitioned Master Code 2 will be assigned to partition 1.29 User Codes: Can arm and disarm as per User Code Options on page 14.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-18.png)
![Magellan 15If the system is partitioned (see Partitioning on page 48), user codes with this option enabled can arm and disarm partition 1. If the system is not partitioned, you must assign partition 1 to the user access code. Otherwise, the user access code will be considered disabled. 5.5.2 Partition 2 AssignmentSections [404] to [432]: User Codes 004 to 032Option [2] OFF = Deny access to partition 2 (default)Option [2] ON = User code has access to partition 2If the system is partitioned (see Partitioning on page 48), user codes with this option enabled can arm and disarm partition 2. If the system is not partitioned, the control panel ignores this option. 5.5.3 Bypass ProgrammingSections [404] to [432]: User Codes 004 to 032Option [3] OFF = Bypass Programming Disabled Option [3] ON = Bypass Programming Enabled (default)User codes with this option enabled can perform Bypass Programming in assigned partitions. 5.5.4 Stay/Sleep ArmingSections [404] to [432]: User Codes 004 to 032Option [4] OFF = Stay/Sleep Arming Disabled Option [4] ON = Stay/Sleep Arming Enabled for selected User Code (default)User codes with this option enabled can Stay or Sleep arm assigned partitions.5.5.5 Force ArmingSections [404] to [432]: User Codes 004 to 032Option [5] OFF = Force Arming DisabledOption [5] ON = Force Arming Enabled for selected User Code (default)User codes with this option enabled can Force arm assigned partitions.5.5.6 Arm OnlySections [404] to [432]: User Codes 004 to 032Option [6] OFF = Arm Only Disabled (default)Option [6] ON = Arm Only Enabled for selected User CodeThe user code with this option enabled can arm assigned partitions, but cannot disarm any partitions. The type of arming is dependent on the other User Code Options selected. Please note that with the Arm Only option, the user can cancel a recently armed system by re-entering the access code before the end of the exit delay.5.5.7 PGM ActivationSections [404] to [432]: User Codes 004 to 048Option [7] OFF = User Code follows User Code Options and can activate a PGM (default)Option [7] ON = User Code can activate a PGM only With option [7] off, entering the access code will arm or disarm according to the programmed User Code Options as well as activate or deactivate a PGM. The appropriate PGM Activation/Deactivation Event must also be programmed (see Programmable Outputs on page 46). With option [7] on, the control panel will ignore all other User Code Options. Therefore, entering the access code will only activate or deactivate the PGM. 5.5.8 DuressSections [404] to [432]: User Codes 004 to 032Option [8] OFF = User Code with duress disabled (default)Option [8] ON = User Code with duress enabled If you are coerced into arming or disarming your system, entering the access code with the duress option enabled will arm or disarm the system and immediately transmit a silent alert (Duress Code) to the monitoring station. 5.6 Lock Master CodeSection [701]: System OptionsOption [2] OFF = Lock System Master Code Disabled (default)Option [2] ON = Lock System Master Code EnabledWith this feature enabled, the control panel will lock the System Master Code (001), it cannot be modified. With this feature disabled, the control panel will unlock the System Master Code, so that it can be changed. The System Master Code cannot be deleted (see Master Quick Menu Programming in the User Guide).](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-19.png)
![16 Reference & Installation Manual Part 6: StayD Mode6.1 Overview•NOTE: StayD is automatically enabled when a path is programmed to a keypad. When deleting a wireless keypad (K32RF) from the system, the corresponding path zones will also be deleted. StayD simplifies your life and makes it safer by protecting you 24 hours a day, 7 days a week without ever having to disarm the system - even when entering an armed area. StayD lives with you and protects you at all times, without any unprotected periods, and while automatically rearming the system so you don’t have to remember to do it. This unique feature integrates security into your everyday life to give you safe, simple living with peace of mind. 6.2 Entry/Exit Paths• StayD consists of programmed pathways, where the user enters and exits the property through pre-defined routes, with only the route’s respective zones open for passage. A path can be programmed for each individual keypad, with a maximum of four zones per path. Path zones must be defined as follow or delay zones only. StayD is automatically enabled when a path is programmed to a keypad.• The first zone programmed in a path is its designated entry point (e.g. doors, garage). Designated entry points are not common to multiple paths. There is only one designated entry point per path. Also, they are only used when entering/exiting with a remote control (see below). • The system only disables the path zones corresponding to the keypad at the point of entry/exit, while re-arming as you enter/exit. • If another path zone opens before trying to disarm the system, you can validate the zone by entering your user code. For example, you have entered your home through Path 1 and are at your keypad. Before disarming the system, you notice a Path 2 zone has opened. If you know it is a member of your family and would like to validate the open zone, enter your user code. All paths, including Path 1, will subsequently be validated. If the path 2 zone opens after you have entered your code to validate Path 1, you must enter your code again to validate Path 2. • You must enter your code for every zone that opens that is not part of any path. For example, if you have entered through Path 1 and a non-path zone opens, you must enter your code once to validate your path and once for the non-path zone. If you do not validate the non-path zone, the system will fall in alarm.6.3 Entry/Exit with a Keypad• When entering with a keypad, the path zones will fall into entry delay, allowing you to reach the keypad. Use the keypad to disarm the system and switch to Stay arm mode.• When exiting with a keypad, only the path zones will fall into delay (same as exit delay), allowing you to leave while the rest of the premises remains secure.6.4 Entry/Exit with a Remote Control• When using a remote control, the path you use is defined by a designated entry point. For example: if after pressing the remote control to disarm the system you trigger zone 1, the system will check to see which path(s) include zone 1. All paths that include zone 1 will open. Only after reaching the designated entry point will the system know which path you are taking, and thus will re-arm all other paths. After entry with a remote, the system will automatically arm in Stay mode.• To disarm the system with a remote control: Press once to disarm partition 1, twice for partition 2, and three times for both partitions. Press the button four times to cancel the exit delay and arm the system in Stay mode.6.5 Window Mode and Re-arm Delay• In a Stay-armed system: This mode allows you to open one exterior zone without triggering an alarm. To enter Window mode, press [OFF], then your [ACCESS CODE]. All zones that can be opened flash. The system will start an exit delay, allowing you to open an exterior zone such as a window or a door. The system will only allow you to open one zone as the exit delay will end after doing so. When you close the open zone (window, door, etc.) that zone will re-arm.• Re-arm Delay is a delay timer set so that when you close the open exterior zone (window, door etc.), it does not re-arm instantly. Instead the system starts the delay to allow you to close the zone properly. The delay will start every time you open the zone while trying to close it, and you must close the zone for 5 seconds for it to arm. This is especially useful for eliminating false alarms caused by windows that stick.6.6 Advanced SettingsSection Data Description[720] __/__/__ (000 to 255) sec. Flex-Instant = Instant and follow zones will follow the delay at section [720] when Stay or Sleep armed (default is 15 seconds / 000 = instant zone). Section Data Description[721] __/__/__ (000 to 255) sec. Re-arm delay (delay before zone re-arms). Default = 000 (no delay)](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-20.png)
![Magellan 17Part 7: Zone ProgrammingWhen programming zones, the zone assignments are dependent on the designation of the wireless transmitters, assignment of keypad zones, and the detection devices that are connected to the panel. For wireless assignment, see Wireless Transmitter Programming on page 25 or the Installer Quick Menu of the programming guide. For keypad assignment, see Configuring the Keypad Zone Number on page 9. After assigning the required zones, you must set the zone’s definitions, partition assignment, and options see Figure 7 below. Certain Zone Definitions change if a Flex-Instant delay is activated (section [720]). See see Zone Definition Status on page 21.Table 3: Zone Recognition Table If a zone is already programmed and you assign a device to the same zone, a wireless zone will overwrite a keypad/hardwire zone, and a keypad zone will overwrite a hardwire zone.Figure 7: Zone Programming7.1 Zone DefinitionsAs demonstrated in Figure 8 above, sections [001] to [032] represent zones 1 through 32 respectively, where the first two digits in each of these sections represents the zone's definition. To disable a zone, enter [00]. There are 26 available Zone Definitions. 7.1.1 Entry Delay 1 ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 01When the system is armed and a zone defined with Entry Delay 1 opens, the control panel will generate an alarm after the programmed Entry Delay 1 Timer elapses. This is to provide users with enough time to enter the protected area and disarm the system. To program the Entry Delay 1 Timer, key in the desired 3-digit delay value (000 to 255 seconds, Default = 45 seconds) into section [710]. Entry delay zones are commonly used at the entry/exit points of the protected area (i.e. front/back door, garage, etc.). Using different entry delays is useful when, for example, one entry point requires a longer delay than the other entry point or in a partitioned system where each partition may require a different entry delay.7.1.2 Entry Delay 2 ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 02Entry Delay 2 zones are identical to the Entry Delay 1 zones, except it uses a separate entry delay timer. To program the Entry Delay 2 Timer, key in the desired 3-digit delay value (000 to 255 seconds, Default = 45 seconds) into section [711].Wireless Keypad HardwireZone 1 Yes Yes Yes (Input Z1)Zone 2 Yes Yes Yes (Input Z2)Zone 3 Yes Yes Yes (Input Z1 with ATZ)Zone 4 Yes Yes Yes (Input Z2 with ATZ)Zone 5 to 32 Yes Yes NoSection Zone Definition Partition Assignment Zone Options[001] = Zone 1 _____/_____ _____________ 1 2 3 4 5 6 7 8[032] = Zone 32 _____/_____ _____________ 1 2 3 4 5 6 7 8Zone Definitions 00 = Zone disabled01 = Entry Delay 102 = Entry Delay 203 = Entry Delay 1 (Full Arm)04 = Entry Delay 2 (Full Arm)05 = Follow06 = Follow (Sleep / Full Arm) 07 = Follow (Full Arm)08 = Instant09 = Instant (Sleep / Full Arm)10 = Instant (Full Arm)11 = Instant Fire12 = Delayed Fire13 = Instant Fire Silent14 = Delayed Fire Silent15 = 24Hr. Buzzer16 = 24Hr. Burglary17 = 24Hr. Hold-up18 = 24Hr. Gas19 = 24Hr. Heat20 = 24Hr. Water21 = 24Hr. Freeze22 = 24Hr. Panic23 = Instant No Pre-Alarm24 = Follow no Pre-Alarm25 = Keyswitch Maintain*26 = Keyswitch Momentary** On-board hardwire control panel zones onlyZone Options[1] = Auto-zone Shutdown [2] = Bypassable Zone [3] = RF Zone Supervision [4] [5]OFF OFF Audible AlarmOFF ON Pulsed AlarmON OFF Silent AlarmON ON Report Only[6] = Intellizone[7] = Delay alarm transmission[8] = Force ZonePartition Assignment[1]- Partition 1[2]- Partition 2[3]- Both partitions](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-21.png)
![18 Reference & Installation Manual 7.1.3 Entry Delay 1 (Full Arm) ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 03Upon regular arming, the zone is Entry Delay 1 (see Entry Delay 1 Zones on page 17). Upon Stay/Sleep arming, the zone is bypassed by the system. See Zone Definition Status on page 21 for any exceptions.7.1.4 Entry Delay 2 (Full Arm) ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 04Upon regular arming, the zone is Entry Delay 2 (see Entry Delay 2 Zones on page 17). Upon Stay/Sleep arming, the zone is bypassed by the system. See Zone Definition Status on page 21 for any exceptions.7.1.5 Follow ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 05When a Regular, Stay, or Sleep armed Follow Zone opens, the control panel will immediately generate an alarm, unless an entry delay zone opens first: • If a Regular/Stay/Sleep armed Follow Zone opens after an entry delay zone opens, the control panel waits until the entry delay timer has elapsed before generating an alarm.• If a Regular/Stay/Sleep armed Follow Zone opens after more than one entry delay zone opens, the control panel will wait until the entry delay timer of the zone that opened first has elapsed.This feature is commonly used when a motion detector is protecting the area occupied by the entry point keypad. This will prevent the motion detector from causing an alarm when a user enters through the entry point to disarm the system. See Zone Definition Status on page 21 for any exceptions. 7.1.6 Follow (Sleep / Full Arm)Sections [001] to [032]: Zones 1 to 32, First Digits = 06Upon regular arming or sleep arming, the zone is Follow. Upon Stay arming, the zone is bypassed by the system. See Zone Definition Status on page 21 for any exceptions.7.1.7 Follow (Full Arm) ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 07Upon regular arming, the zone is Follow (see Follow Zones on page 18). Upon Stay or Sleep arming, the zone is bypassed by the system. See Zone Definition Status on page 21 for any exceptions.7.1.8 Instant ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 08When an armed Instant Zone opens, the control panel immediately generates an alarm. Instant Zones are commonly used for windows, patio doors, skylights and other perimeter type zones. See Zone Definition Status on page 21 for any exceptions.7.1.9 Instant (Sleep / Full Arm) ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 09When Regular or Sleep arming, the zone is Instant. When Stay arming, the zone is bypassed by the system. See Zone Definition Status on page 21 for any exceptions.7.1.10 Instant (Full Arm) ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 10Upon Regular arming, the zone is Instant. Upon Stay or Sleep arming, the zone is bypassed by the system. See Zone Definition Status on page 21 for any exceptions.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-22.png)
![Magellan 197.1.11 Instant Fire ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 11when a Instant Fire zone opens, whether it is armed or disarmed, the control panel will send the corresponding Alarm Report Code and the alarm is always audible regardless of other settings. Fire alarms generate an intermittent (pulsed) bell/siren output signal as shown in Figure 8 on page 19.Figure 8: Bell/Siren Output during a Fire Alarm7.1.12 Delayed Fire ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 12When a Delayed 24Hr. Fire zone opens, whether it is armed or disarmed, the control panel will react as shown in Figure 9. Delayed 24Hr. Fire zones are commonly used in residential homes where a smoke detector often generates false alarms (i.e., burning bread, etc.). Fire alarms generate an intermittent (pulsed) bell/siren output signal as shown in Figure 8 above.7.1.13 Instant Fire Silent ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 13When a Instant Fire Silent zone opens, whether it is armed or disarmed, the control panel will generate the following:The control panel can send the corresponding Alarm Report Code and the alarm will be silent regardless of other settings.7.1.14 Delayed Fire Silent ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 14When a Delayed Fire zone opens, whether it is armed or disarmed, the control panel will react as shown in Figure 9. Delayed 24Hr. Fire zones are commonly used in residential homes where a smoke detector often generates false alarms (i.e., burning bread, etc.). The control panel can send the corresponding Alarm Report Code and the alarm will be silent regardless of other settings.7.1.15 24 Hr. Buzzer ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 15When a 24Hr Buzzer Zone opens, whether the zone is armed or disarmed, the control panel sets off the keypad’s buzzers to indicate that the zone was breached. The control panel will report the alarm, but will not enable the bell/siren output. Enter any valid access code on the keypad to stop the buzzer. This zone definition is particularly useful when a user wishes to be notified when something such as a safe or locker within the home has been accessed (i.e. a child accessing a valuable collection).7.1.16 24 Hr. Burglary ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 16when a 24Hr Burglary Zone opens, whether the system is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 22. Figure 9: Delayed 24Hr Fire Zone](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-23.png)
![20 Reference & Installation Manual 7.1.17 24 Hr. Hold-up ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 17When a 24Hr. Hold-up zone opens, whether it is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 22. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Hold-up alarm. 7.1.18 24 Hr. Gas ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 18When a 24Hr. Gas zone opens, whether it is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 22. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Gas alarm.7.1.19 24 Hr. Heat ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 19When a 24Hr. Heat zone opens, whether it is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 22. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Heat alarm.7.1.20 24 Hr. Water ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 20When a 24Hr. Water zone opens, whether it is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 22. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Water alarm.7.1.21 24 Hr. Freeze ZonesSections [001] to [032]: Zones 1 to 32, First Digits = 21When a 24Hr. Freeze zone opens, whether it is armed or disarmed, the control panel will immediately generate an alarm. This alarm is defined by the alarm type, configured in Zone Programming under zone options [4] and [5]. See Alarm Types on page 22. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Freeze alarm.7.1.22 24Hr. PanicSections [001] to [032]: Zones 1 to 32, First Digits = 22When a 24Hr. Panic zone opens, whether it is armed or disarmed, the system will immediately generate an alarm. This alarm is defined by the panic options set in section [702]. The SIA FSK and CID reporting formats include specific report codes to identify the alarm as a Panic alarm. Section [702] option [1] (Panic 1) must be enabled for the 24Hr. Panic zone to function.7.1.23 Instant No Pre-AlarmSections [001] to [032]: Zones 1 to 32, First Digits = 23This zone definition ignores the Flex-Instant delay, and acts like a traditional Instant zone.7.1.24 Follow No Pre-AlarmSections [001] to [032]: Zones 1 to 32, First Digits = 24This zone definition ignores the Flex-Instant delay, and acts like a traditional Follow zone.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-24.png)
![Magellan 217.2 Zone Definition StatusThere are eight zone definitions that are affected by the Flex-Instant delay (section [720]). The following table shows how the zone definition changes depending on the arm status and if the Flex-Instant delay is enabled. see Zone Definition Status on page 21.7.3 Zone Partition AssignmentSections [001] to [032]: Zones 1 to 32 The control panel provides the option of partitioning the security system into two completely independent systems. Sections [001] to [032] represent zones 1 through 32 respectively, where the third digit in each of these sections represents the zone's partition assignment. The zone is assigned to Partition 1 if third digit = 1, Partition 2 if third digit = 2, or both partitions is third digit = 3. For more details, see Partitioning on page 48. 7.4 Zone OptionsSections [001] to [032] represent zones 1 through 32 respectively. After entering the definition and partition assignment, select one or more of the following Zone Options by using the Multiple Feature Select Programming Method:7.4.1 Auto Zone ShutdownSections [001] to [032] = Zones 1 to 32Option [1] OFF = Auto Zone Shutdown Disabled Option [1] ON = Auto Zone Shutdown Enabled for selected zone (default)If, in a single armed period, the number of alarms generated by a zone with the Auto Zone Shutdown option enabled exceeds the number defined by the Auto Zone Shutdown Counter, the control panel will no longer generate an alarm for that zone. To program the Auto Zone Shutdown Counter, key in the desired limit (000=Disabled, 001 to 015, Default = 5) into section [712]. The Auto Zone Shutdown Counter resets every time a valid code is entered.7.4.2 Bypassable ZonesSections [001] to [032] = Zones 1 to 32Option [2] OFF = Bypass Zone Disabled Option [2] ON = Selected Zone is Bypass Enabled (default)When a user utilizes the Bypass Programming feature (see Bypass Programming on page 15), only zones with the Bypass option enabled can be programmed as bypassed.Do not program a fire zone with the Bypass option, as the control panel will never bypass fire zones. Zone Definitions Stay Arm Sleep Arm Fully Arm01 = Entry Delay 1 Entry Delay 1 Entry Delay 1 Entry Delay 102 = Entry Delay 2 Entry Delay 2 Entry Delay 2 Entry Delay 203 = Entry Delay 1 (Full Arm) Not Armed Not Armed Entry Delay 104 = Entry Delay 2 (Full Arm) Not Armed Not Armed Entry Delay 205 = Follow Follow*Follow*Follow*06 = Follow (Sleep/Full Arm) Not Armed Follow*Follow07 = Follow (Full Arm) Not Armed Not Armed Follow08 = Instant Instant*Instant*Instant*09 = Instant (Sleep/Full Arm) Not Armed Instant*Instant10 = Instant (Full Arm) Not Armed Not Armed Instant23 = Instant No Pre-Alarm Instant Instant Instant*24 = Follow No Pre-Alarm Follow Follow Follow** Flex-Instant = Zone will follow the delay at section [720], (default is 15 seconds / 0 = instant zone)](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-25.png)
![22 Reference & Installation Manual 7.4.3 RF Zone SupervisionSections [001] to [032]: Zones 1 to 32Option [3] OFF = RF Zone Supervision Disabled Option [3] ON = RF Zone Supervision Enabled (default)The panel waits for each of its assigned wireless transmitters to send a status signal within a specified time period (section [706], option [1]) to confirm their presence and functionality. If a device has not sent a signal within that time period, the control panel can generate a trouble, an alarm, and/or transmit a report code to the monitoring station. See Trouble Display on page 53.7.4.4 Alarm TypesSections [001] to [032]: Zones 1 to 32[4] OFF / [5] OFF: Audible Steady (default) When the conditions for an alarm have been met, the control panel can transmit the appropriate Zone Alarm report code and provides a steady output for any bells or sirens connected to the control panel’s bell output. [4] OFF / [5] ON: Audible Pulsed AlarmWhen the conditions for an alarm have been met, the control panel can transmit the appropriate Zone Alarm report code and provides a pulsed output (see Figure 8 on page 19) for any bells or sirens connected to the control panel’s bell output. [4] ON / [5] OFF: Silent Alarm When the conditions for an alarm are met, the control panel can transmit the appropriate Zone Alarm report code and will not activate the control panel’s bell output. The appropriate ARM or STATUS LED on the keypads will flash to indicate an alarm and the user will still have to disarm the system.[4] ON / [5] ON: Report Only When the conditions for an alarm have been met, the control panel can transmit the appropriate Zone Alarm report code. The system will not have to be disarmed.7.4.5 IntellizoneSections [001] to [032]: Zones 1 to 32Option [6] OFF = Intellizone Disabled (default)Option [6] ON = Intellizone Enabled for Selected ZoneThis feature reduces the possibility of false alarms. When a zone with the Intellizone option opens, the panel does not immediately generate an alarm. First it triggers the Intellizone Delay Timer. To program the Intellizone Delay Timer, key in the desired 3-digit value (000 to 255 seconds, Default = 48 seconds) into section [713]. If any of the following conditions occur during this period, the panel will generate an alarm:• During the Intellizone Delay, a second zone has caused an alarm.• During the Intellizone Delay, the zone in alarm has restored (closed) and re-occurred (opened).• The zone in alarm remains open for the entire Intellizone Delay.7.4.6 Delay Alarm Transmission Sections [001] to [032]: Zones 1 to 32Option [7] OFF = Delay Alarm Transmission Disabled (default)Option [7] ON = Delay Alarm Transmission Enabled for Selected ZoneWhen an alarm condition occurs on a zone with this option enabled, the control panel enables the bell/siren output, but does not report the alarm to the monitoring station until the end of the Delay Alarm Transmission. To program the Delay Alarm Transmission, key in the desired 3-digit delay value (000 = Disabled, 001 to 255 seconds) into section [833]. During this period, disarming the system disables the bell/siren output and cancels the report code transmission. This feature is commonly used with entry delay zones to reduce false alarms created by new users who may not disarm the system in time.7.4.7 Force ZonesSections [001] to [032]: Zones 1 to 32Option [8] OFF = Force Zone Disabled Option [8] ON = Selected Zone is Force Enabled (default)Any open Force Zones at the time of arming will be considered deactivated by the control panel. If during this period a deactivated zone is closed, the control panel will revert that zone to active status. Consequently, the control panel will generate an alarm if the zone is breached.Do not program a fire zone with the Force option, as the control panel will never bypass fire zones when Force arming.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-26.png)
![Magellan 237.5 EOL ZonesSection [706]: Zone OptionsOption [2] OFF = Zones do not use EOL resistors (default)Option [2] ON = Zones require EOL resistorsIf all detection devices connected to the control panel have input terminals that require 1K end of line resistors, enable option [2] in section [706]. For details on using EOL resistors, see Single Zone Inputs on page 6.7.6 ATZ Zone DoublingSection [705]: General Zone OptionsOption [1] OFF = ATZ zone doubling disabled (default)Option [1] ON = ATZ zone doubling enabledEnabling ATZ Zone Doubling allows you to install two detection devices per input terminal.7.7 Tamper Input on ZX8 ID A (Panel + 1)Section [706]: General Zone Options 2Option [4] OFF = Zone A (default)Option [4] ON = Tamper inputEnabling this option will make the first zone on the ZX8 ID A (Panel +1) a tamper input. By default, it is a zone.7.8 Tamper Input on ZX8 ID B (Panel + 9)Section [706]: General Zone Options 2Option [5] OFF = Zone B (default)Option [5] ON = Tamper inputEnabling this option will make the first zone on the ZX8 ID B (Panel +9) a tamper input. By default, it is a zone.7.9 Tamper Input on ZX8 ID C (Panel + 17)Section [706]: General Zone Options 2Option [6] OFF = Zone C (default)Option [6] ON = Tamper inputEnabling this option will make the first zone on the ZX8 ID C (Panel +17) a tamper input. By default, it is a zone.7.10 ATZ Wiring OptionsSection [705]: General Zone OptionsOption [2] OFF = ATZ Series (default)Option [2] ON = ATZ Parallel doubling enabledATZ Zone Doubling can be configured in either a series or parallel connection.7.11 Zone Input 1 Becomes a 2-wire Smoke InputSection [706]: General Zone OptionsOption [3] OFF = Zone input 1 is a standard zone input (default)Option [3] ON = Zone input 1 becomes a 2-wire smoke inputWith this option enabled, zone input 1 becomes a 2-wire smoke input.7.12 Zone TimersSections [041] to [044]: Zones 1 to 4 001 to 255 X 10ms, Default = 060The Zone Timer defines how quickly the control panel will respond to an open zone. The control panel will not display an open zone on the keypad or generate an alarm until the programmed Zone Timer has elapsed. All other zone definitions and options do not come into effect until the Zone Timer has elapsed. This feature prevents any momentary glitches from causing an alarm or unnecessary reporting.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-27.png)
![24 Reference & Installation Manual Part 8: Keyswitch Programming8.1 Keyswitch NumberingOn-board hardwire control panel zones only.Keyswitch Numbering allows you to assign any hardwired input in the system to any of the 32 keyswitch zones in the control panel. UL Note: Do not use keyswitches in UL Listed systems.8.2 Keyswitch DefinitionsKeyswitch Definitions determine how a keyswitch is used. 8.2.1 Maintained KeyswitchOn-board hardwire control panel zones only.To arm a partition using the Maintained Keyswitch, turn the switch from the ON to the OFF position. Disarm it by setting the key on the ON position.8.2.2 Momentary KeyswitchOn-board hardwire control panel zones only.To arm or disarm a partition using the Momentary Keyswitch, turn the keyswitch to the ON position for three seconds, then turn it to the OFF position.8.3 Keyswitch OptionsEach keyswitch zone can be programmed with one or more options.8.3.1 Stay/Sleep Disarm Option (Keyswitch)On-board hardwire control panel zones only: Option 4When enabled, the keyswitch can only disarm assigned Stay or Sleep armed partitions. When option [4] is disabled, the keyswitch can disarm partitions armed using any arming method.8.3.2 Arm Only (Keyswitch)On-board hardwire control panel zones only: Option 5When enabled, the keyswitch can only arm assigned partitions. The type of arming is determined by the other Keyswitch Options selected.8.3.3 Stay Arming (Keyswitch)On-board hardwire control panel zones only: Option 6Activating the keyswitch will Stay Arm the partition. 8.3.4 Sleep Arming (Keyswitch)On-board hardwire control panel zones only: Option 7Activating the keyswitch will Sleep Arm the partition.Only one of the arming options (Stay, Force, Instant and Regular) can be selected.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-28.png)
![Magellan 25Part 9: Wireless FeaturesThe control panel(s) allows for the addition of up to thirty-two fully supervised wireless transmitters, and up to thirty-two programmable remote controls. 9.1 Wireless Transmitter ProgrammingThe programming of the wireless transmitters (detectors and door contacts) is accomplished in two steps:1. Assign the wireless transmitter to the control panel.2. Program the zones.Wireless Transmitter Programming can be executed through the Installer Quick Menu in the programming guide. Sections [061] to [092] represent expansion inputs 1 to 32 respectively. The serial number is located on the inside of the transmitter or you can use the Serial Number Display (section [960]) to determine its serial number. The transmitters must be activated once having been assigned to the control panel. To activate a transmitter, insert the batteries and close the cover. To ensure proper synchronization between the control panel and the transmitter, open and close the zone corresponding to the transmitter.9.2 Viewing the Wireless Transmitter Signal StrengthSections [101] to [132]Once wireless transmitters have been installed and assigned to the control panel, the signal strength of each transmitter can be verified in sections [101] to [132]. Each section represents the signal strength viewer for a specific device. For example, section [101] is the viewer for zone 1 and section [132] is the viewer for the zone 32. Sometimes moving the transmitter or control panel by a small amount will greatly increase the signal reception.9.3 Supervision OptionsThe Supervision Options cannot be used with any remote controls assigned to the control panel.9.3.1 Supervision Bypass OptionsSection [705]: Arming/Disarming OptionsOption [8] ON = Generate Supervision Loss if detected on a Bypassed Wireless Transmitter Zone (default)Option [8] OFF = No Supervision Loss if detected on a Bypassed Wireless Transmitter ZoneWhen this feature is disabled, the Wireless Transmitter Supervision Options will follow the zone’s bypass definition. This means the control panel will not perform any action if a Supervision Loss occurs on a bypassed zone. When this feature is enabled, the Wireless Transmitter Options will ignore the bypass definition. This means the control panel will generate an incident as per Wireless Transmitter Supervision Options if a supervision loss occurs on a bypassed zone. How Do I Assign Wireless Transmitters to the Panel?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter the desired [SECTION NUMBER] (from sections [061] to [092]).4) Enter the 6-digit [SERIAL NUMBER] of the wireless transmitter.How Do I Delete Assigned Wireless Transmitters?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter the desired [SECTION NUMBER] (from sections [061] to [092]).4) Press the [0] key six times to clear the serial number.How Do I View a Wireless Transmitter’s Signal Strength?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter the desired [SECTION NUMBER] (from sections [101] to [132]).4) Press the transmitter’s anti-tamper switch or open the corresponding zone.5) The keypad will illuminate numbers 1 to 10.Signal Strength Indicator 8 to 10 / 3 beeps = Best signal 5 to 7 / 2 beeps = Average signal 1 to 4 / 1 beep = Weak signal (Relocate)](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-29.png)
![26 Reference & Installation Manual 9.3.2 RF Module Supervision Timer SettingsSection [706]: Supervision OptionsOption [1] OFF = Check-in supervision interval is every 24 hours (default)Option [1] ON = Check-in supervision interval is every 80 minutesOption [1] defines the time period that the control panel will expect a check-in status signal from its assigned wireless transmitters. For example, if the timer is set to 80 minutes (option [1] = ON), the control panel will expect a check-in status signal to be sent from its assigned wireless transmitters within 80 minutes. If the control panel does not receive a signal from one of its wireless transmitters within the period of time defined here, it can then generate a trouble, an alarm, and/or can transmit a report code to the monitoring station (see Supervision Options on page 25). 9.4 RF Jamming SupervisionSection [700]: Zone OptionsOption [5] OFF = RF Jamming Supervision DisabledOption [5] ON = RF Jamming Supervision Enabled (default)With option [5] ON, a trouble will be generated when the panel’s RF signal is jammed or encounters interference for a minimum of 10 seconds.9.5 Wireless Serial Number DisplaySection [960]: Find Wireless Serial Number DisplayTo see the wireless serial number display, enter section [960]. Press the anti-tamper switch of the desired module to be viewed. The first digit of the serial number will illuminate on the keypad. Press [ENTER] to see each consecutive digit. Press [CLEAR] to exit.9.6 Remote Control ProgrammingThe control panel accepts up to thirty-two fully programmable remote controls. Programming the remote controls is accomplished in two steps:1) Assign the remote controls to the control panel.2) Program the buttons on the remote controls.9.6.1 Assigning a Remote Control to the Control PanelSections [651] to [682]: Remote Controls 1 to 32 respectivelyRemote controls are assigned to the panel using the Automatic Learning method via the MAster Quick Menu Programming or by entering the serial number.9.6.2 Deleting Assigned Remote ControlsSections [651] to [682]: Remote Controls 1 to 32 respectivelyRemote controls can be deleted by deleting the corresponding user (see the Quick Menu in the user guide).9.6.3 Programming the Remote Control ButtonsSections [611] to [642]: Remote Controls 1 to 32 respectivelyEach remote control can be programmed to perform up to 4 different actions. Each digit in sections [611] to [642] represents a button or combination of buttons. Digits 1 through 4 can be programmed, while digits 5 through 8 are reserved for future use and must be defined as empty (reminder: [SLEEP] = empty). How Do I Assign a Remote Control to the Control Panel?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter the desired [SECTION NUMBER] (from sections [651] to [682]).4)Enter the six-digit serial number of the remote.How Do I Delete a Remote Control?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter the desired [SECTION NUMBER] (from sections [651] to [682]).4) Press the [0] button six times to delete the serial number.How Do I Program the Remote Control’s Buttons?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter the desired [SECTION NUMBER] (from sections [610] to [642]).4) Enter the [HEXADECIMAL VALUE] (0 to F) of the desired button option from Table 4 on page 27 in the appropriate space. If you do not wish to program a button combination, press the [SLEEP] key to skip.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-30.png)
![Magellan 27Warning: When section [610] is accessed, the panel will copy the saved value of that section to all remotes.9.7 Wireless Keypad AssignmentSections [571] to [578]Automatic Assignment: After panel power-up, the control panel will open a 10 minute window for Automatic Assignment. Press and hold the [] and [BYP] key for three seconds on the respective keypad. The keypad is assigned to the control panel. Up to 8 wireless keypads can be assigned within the ten minute window. Standard Assignment: Press [ENTER]. Enter your [INSTALLER CODE] or [MAINTENANCE CODE]. Go to section(s) [571] = Keypad 1, [572] = Keypad 2, [573] = Keypad 3, or [574] = Keypad 4, [575] = Keypad 5, [576] = Keypad 6, [577] = Keypad 7, or [578] = Keypad 8Press and hold the [] and [BYP] key for three seconds on the respective keypad. The keypad is assigned to the control panel. Alternatively, enter the serial number of the K32RF into one of the eight sections to assign it to the panel. 9.8 Viewing the Wireless Keypad Signal StrengthSections [591] to [598]Once wireless keypads have been installed and assigned to the control panel, the signal strength of each transmitter can be verified in sections [591] to [598]. Each section represents the signal strength viewer for a specific keypad. For example, section [591] is the viewer for keypad 1 and section [598] is the viewer for the keypad 8. Sometimes moving the keypad by a small amount will greatly increase the signal reception.9.9 Wireless Keypad OptionsSection [588]: Wireless Keypad OptionsIf enabled, the panel can wait for each of its assigned wireless transmitters to send a status signal within a specified time to confirm their presence and functionality.Option [1] OFF = Keypad 1 Supervision Disabled Option [1] ON = Keypad 1 Supervision Enabled (default)Option [2] OFF = Keypad 2 Supervision Disabled Option [2] ON = Keypad 2 Supervision Enabled (default)Option [3] OFF = Keypad 2 Supervision Disabled Option [3] ON = Keypad 2 Supervision Enabled (default)Option [4] OFF = Keypad 2 Supervision Disabled Option [4] ON = Keypad 2 Supervision Enabled (default)Option [5] OFF = Keypad 2 Supervision Disabled Option [5] ON = Keypad 2 Supervision Enabled (default)Option [6] OFF = Keypad 2 Supervision Disabled Option [6] ON = Keypad 2 Supervision Enabled (default)Table 4: Button Options[0] = Button Disabled* [8] = Generate a Panic 1 Alarm [1] = Regular/Regular Force arming [9] = Generate a Panic 2 Alarm [2] = Stay/Stay Force arming [0] or [0(10)] = Generate a Panic 3 Alarm[3] = N/A [OFF] = Activates any PGMs that have Event Group #08 as their Activation Event[4] = Sleep/Sleep Force arming [BYP] = Activates any PGMs that have Event Group #09 as their Activation Event[5] = N/A [MEM] = Activates any PGMs that have Event Group #10 as their Activation Event[6] = N/A [TBL] = Activates any PGMs that have Event Group #11 as their Activation Event[7] = N/A [] = Paramedic alarm* If you do not enter a value for a button, that button is disabled.How Do I View a Wireless Keypad’s Signal Strength?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter the desired [SECTION NUMBER] (from sections [591] to [598]).4) Press the keypad’s anti-tamper switch or open the corresponding keypad zone.5) The keypad will illuminate numbers 1 to 10.Signal Strength Indicator 8 to 10 / 3 beeps = Best signal 5 to 7 / 2 beeps = Average signal 1 to 4 / 1 beep = Weak signal (Relocate)](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-31.png)
![28 Reference & Installation Manual Option [7] OFF = Keypad 2 Supervision Disabled Option [7] ON = Keypad 2 Supervision Enabled (default)Option [8] OFF = Keypad 2 Supervision Disabled Option [8] ON = Keypad 2 Supervision Enabled (default)9.10 Wireless Keypad Live Display ModeSection [587]: Wireless Keypad OptionsOption [8] OFF = Live Display Mode Disabled Option [8] ON = Live Display Mode Enabled (default)The K32RF has two display modes. By default, the keypad will show all events (e.g. zones in alarm, bypassed zones, etc.) live as they occur. Alternatively, with Live Display Mode off, the system will only display zones that cause an alarm or entry delay. If you want to see the status of all zones, press the [ ] key. Zones that are open but have not triggered an alarm will only be displayed after pressing the [ ] key. The display will appear for 30 seconds, showing the status of all zones at the time the [ ] key was pressed. The zone display will shut off after 30 seconds.9.11 Wireless Repeater ProgrammingSections [545] to [546] represent wireless repeater 1 and 2 respectively. The wireless repeater module will improve the range of your system by retransmitting information from zones, PGMs, wireless keypads and the control panel. Note that all remote control signals are always repeated. You can have two RPT1 per system. The wireless repeater also provides one PGM and one zone input with two-way wireless communication with the panel. 9.12 Viewing the Repeater’s Signal StrengthSections [548] to [549]Once the repeaters have been installed and assigned to the control panel, the signal strength of each repeater can be verified in sections [548] to [549]. Section [548] is the viewer for repeater 1 and section [549] is the viewer for the repeater 2. Sometimes moving the repeater or control panel by a small amount will greatly increase the signal reception.9.13 Wireless Repeater OptionsSection [587]: Wireless Repeater OptionsOption [1] OFF = Repeater 1 Supervision Disabled Option [1] ON = Repeater 1 Supervision Enabled (default)Option [2] OFF = Repeater 2 Supervision Disabled Option [2] ON = Repeater 2 Supervision Enabled (default)If enabled, the panel can wait for each of its assigned wireless transmitters to send a status signal within a specified time to confirm their presence and functionality.How Do I Assign Wireless Repeaters to the Panel?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter the desired [SECTION NUMBER] (from sections [545] to [546]).4) Enter the 6-digit [SERIAL NUMBER] of the wireless repeater.How Do I Delete Assigned Wireless Repeaters?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter the desired [SECTION NUMBER] (from sections [545] to [546])4) Press the [0] key six times to clear the serial number.How Do I View a Wireless Transmitter’s Signal Strength?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter the desired [SECTION NUMBER] (from sections [548] to [549]).4) Press the repeater’s anti-tamper switch.5) The keypad will illuminate numbers 1 to 10.Signal Strength Indicator 8 to 10 / 3 beeps = Best signal 5 to 7 / 2 beeps = Average signal 1 to 4 / 1 beep = Weak signal (Relocate)](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-32.png)
![Magellan 299.14 Wireless OptionsSection [551] (Repeater 1) and Section [561] (Repeater 2): Wireless Repeater OptionsEnable or disable the repetition of wireless keypads in this section. Enabling these options for keypads means that the repeater will retransmit any signals relevant to them.Option [1] OFF = Repeat Wireless Keypad 1 Signals (default)Option [1] ON = Repeat Wireless Keypad 1 Signals Option [2] OFF = Repeat Wireless Keypad 2 Signals (default)Option [2] ON = Repeat Wireless Keypad 2 Signals Option [3] OFF = Repeat Wireless Keypad 3 Signals (default)Option [3] ON = Repeat Wireless Keypad 3 SignalsOption [4] OFF = Repeat Wireless Keypad 4 Signals (default)Option [4] ON = Repeat Wireless Keypad 4 SignalsOption [5] OFF = Repeat Wireless Keypad 5 Signals (default)Option [5] ON = Repeat Wireless Keypad 5 Signals Option [6] OFF = Repeat Wireless Keypad 6 Signals (default)Option [6] ON = Repeat Wireless Keypad 6 Signals Option [7] OFF = Repeat Wireless Keypad 7 Signals (default)Option [7] ON = Repeat Wireless Keypad 7 SignalsOption [8] OFF = Repeat Wireless Keypad 8 Signals (default)Option [8] ON = Repeat Wireless Keypad 8 Signals Section [552] (Repeater 1) and Section [562] (Repeater 2): Wireless Repeater OptionsEnable or disable the repetition of zone signals in these sections. Enabling these options for zones means that the repeater will retransmit any signals relevant to them.Option [1] OFF = Repeat Wireless Zone 1 Signals (default)Option [1] ON = Repeat Wireless Zone 1 Signals Option [2] OFF = Repeat Wireless Zone 2 Signals (default)Option [2] ON = Repeat Wireless Zone 2 Signals Option [3] OFF = Repeat Wireless Zone 3 Signals (default)Option [3] ON = Repeat Wireless Zone 3 Signals Option [4] OFF = Repeat Wireless Zone 4 Signals (default)Option [4] ON = Repeat Wireless Zone 4 Signals Option [5] OFF = Repeat Wireless Zone 5 Signals (default)Option [5] ON = Repeat Wireless Zone 5 Signals Option [6] OFF = Repeat Wireless Zone 6 Signals (default)Option [6] ON = Repeat Wireless Zone 6 Signals Option [7] OFF = Repeat Wireless Zone 7 Signals (default)Option [7] ON = Repeat Wireless Zone 7 Signals Option [8] OFF = Repeat Wireless Zone 8 Signals (default)Option [8] ON = Repeat Wireless Zone 8 Signals Section [553] (Repeater 1) and Section [563] (Repeater 2): Wireless Repeater OptionsEnable or disable the repetition of zone signals in these sections. Enabling these options for zones means that the repeater will retransmit any signals relevant to them.Option [1] OFF = Repeat Wireless Zone 9 Signals (default)Option [1] ON = Repeat Wireless Zone 9 Signals Option [2] OFF = Repeat Wireless Zone 10 Signals (default)Option [2] ON = Repeat Wireless Zone 10 Signals Option [3] OFF = Repeat Wireless Zone 11 Signals (default)Option [3] ON = Repeat Wireless Zone 11 Signals Option [4] OFF = Repeat Wireless Zone 12 Signals (default)Option [4] ON = Repeat Wireless Zone 12 Signals Option [5] OFF = Repeat Wireless Zone 13 Signals (default)Option [5] ON = Repeat Wireless Zone 13 Signals](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-33.png)
![30 Reference & Installation Manual Option [6] OFF = Repeat Wireless Zone 14 Signals (default)Option [6] ON = Repeat Wireless Zone 14 Signals Option [7] OFF = Repeat Wireless Zone 15 Signals (default)Option [7] ON = Repeat Wireless Zone 15 Signals Option [8] OFF = Repeat Wireless Zone 16 Signals (default)Option [8] ON = Repeat Wireless Zone 16 Signals Section [554] (Repeater 1) and Section [564] (Repeater 2): Wireless Repeater OptionsEnable or disable the repetition of zone signals in these sections. Enabling these options for zones means that the repeater will retransmit any signals relevant to them.Option [1] OFF = Repeat Wireless Zone 17 Signals (default)Option [1] ON = Repeat Wireless Zone 17 Signals Option [2] OFF = Repeat Wireless Zone 18 Signals (default)Option [2] ON = Repeat Wireless Zone 18 Signals Option [3] OFF = Repeat Wireless Zone 19 Signals (default)Option [3] ON = Repeat Wireless Zone 19 Signals Option [4] OFF = Repeat Wireless Zone 20 Signals (default)Option [4] ON = Repeat Wireless Zone 20 Signals Option [5] OFF = Repeat Wireless Zone 21 Signals (default)Option [5] ON = Repeat Wireless Zone 13 Signals Option [6] OFF = Repeat Wireless Zone 22 Signals (default)Option [6] ON = Repeat Wireless Zone 22 SignalsOption [7] OFF = Repeat Wireless Zone 23 Signals (default)Option [7] ON = Repeat Wireless Zone 23 Signals Option [8] OFF = Repeat Wireless Zone 24 Signals (default)Option [8] ON = Repeat Wireless Zone 24 Signals Section [555] (Repeater 1) and Section [565] (Repeater 2): Wireless Repeater OptionsEnable or disable the repetition of zone signals in these sections. Enabling these options for zones means that the repeater will retransmit any signals relevant to them.Option [1] OFF = Repeat Wireless Zone 25 Signals (default)Option [1] ON = Repeat Wireless Zone 25 Signals Option [2] OFF = Repeat Wireless Zone 26 Signals (default)Option [2] ON = Repeat Wireless Zone 26 Signals Option [3] OFF = Repeat Wireless Zone 27 Signals (default)Option [3] ON = Repeat Wireless Zone 27 Signals Option [4] OFF = Repeat Wireless Zone 28 Signals (default)Option [4] ON = Repeat Wireless Zone 28 Signals Option [5] OFF = Repeat Wireless Zone 29 Signals (default)Option [5] ON = Repeat Wireless Zone 29 Signals Option [6] OFF = Repeat Wireless Zone 30 Signals (default)Option [6] ON = Repeat Wireless Zone 30 Signals Option [7] OFF = Repeat Wireless Zone 31 Signals (default)Option [7] ON = Repeat Wireless Zone 31 Signals Option [8] OFF = Repeat Wireless Zone 32 Signals (default)Option [8] ON = Repeat Wireless Zone 32 Signals](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-34.png)
![Magellan 31Section [556] (Repeater 1) and Section [566] (Repeater 2): Wireless Repeater OptionsEnable or disable the repetition of 2WPGM signals in these sections. Enabling these options for 2WPGMs means that the repeater will retransmit any signals relevant to them.Option [1] OFF = Repeat Wireless 2-Way PGM 1 Signals (default)Option [1] ON = Repeat Wireless 2-Way PGM 1 Signals Option [2] OFF = Repeat Wireless 2-Way PGM 2 Signals (default)Option [2] ON = Repeat Wireless 2-Way PGM 2 Signals Option [3] OFF = Repeat Wireless 2-Way PGM 3 Signals (default)Option [3] ON = Repeat Wireless 2-Way PGM 3 Signals Option [4] OFF = Repeat Wireless 2-Way PGM 4 Signals (default)Option [4] ON = Repeat Wireless 2-Way PGM 4 Signals Option [5] OFF = Repeat Wireless 2-Way PGM 5 Signals (default)Option [5] ON = Repeat Wireless 2-Way PGM 5 Signals Option [6] OFF = Repeat Wireless 2-Way PGM 6 Signals (default)Option [6] ON = Repeat Wireless 2-Way PGM 6 SignalsOption [7] OFF = Repeat Wireless 2-Way PGM 7 Signals (default)Option [7] ON = Repeat Wireless 2-Way PGM 7 Signals Option [8] OFF = Repeat Wireless 2-Way PGM 8 Signals (default)Option [8] ON = Repeat Wireless 2-Way PGM 8 Signals Section [557] (Repeater 1) and Section [567] (Repeater 2): Wireless Repeater OptionsEnable or disable the repetition of 2WPGM signals in these sections. Enabling these options for 2WPGMs means that the repeater will retransmit any signals relevant to them.Option [1] OFF = Repeat Wireless 2-Way PGM 9 Signals (default)Option [1] ON = Repeat Wireless 2-Way PGM 9 Signals Option [2] OFF = Repeat Wireless 2-Way PGM 10 Signals (default)Option [2] ON = Repeat Wireless 2-Way PGM 10 Signals Option [3] OFF = Repeat Wireless 2-Way PGM 11 Signals (default)Option [3] ON = Repeat Wireless 2-Way PGM 11 Signals Option [4] OFF = Repeat Wireless 2-Way PGM 12 Signals (default)Option [4] ON = Repeat Wireless 2-Way PGM 12 Signals Option [5] OFF = Repeat Wireless 2-Way PGM 13 Signals (default)Option [5] ON = Repeat Wireless 2-Way PGM 13 Signals Option [6] OFF = Repeat Wireless 2-Way PGM 14 Signals (default)Option [6] ON = Repeat Wireless 2-Way PGM 14 Signals Option [7] OFF = Repeat Wireless 2-Way PGM 15 Signals (default)Option [7] ON = Repeat Wireless 2-Way PGM 15 Signals Option [8] OFF = Repeat Wireless 2-Way PGM 16 Signals (default)Option [8] ON = Repeat Wireless 2-Way PGM 16 Signals](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-35.png)
![32 Reference & Installation Manual Part 10: Arming and Disarming Options10.1 Switch to Stay Arming if no Entry Delay is opened Section [741]: Partition 1, Section [742] = Partition 2 Option [5] OFF = Switch to Stay Arming Disabled (default)Option [5] ON = Switch to Stay Arming EnabledIf a user Regular arms a partition, but does not exit through (open and close) an entry delay zone during the exit delay, the control panel can be programmed to switch from Regular arming to Stay arming.10.2 When Delay Zone is bypassed Follow Zones become Entry Delay 2 Section [741]: Partition 1, Section [742] = Partition 2 Option [6] OFF = Follow zones become entry delay 2 when delay zone is bypassed disabled (default)Option [6] ON = Follow zones become entry delay 2 when delay zone is bypassed enabled If a user has an entry point defined as a delay, and a motion detector set as a follow zone, this option allows the user to bypass a delay zone so that the motion detector becomes an entry delay 2 zone. For example, if a user has a malfunctioning door contact, they can bypass the delay zone and have the motion detector become an entry delay 2 zone so that they have sufficient time to disarm the system. All follow zones become entry delay 2 if at least one delay zone is bypassed.10.3 Regular Arming switches to Force Arming(Not to be used with UL Installations)Section [704]: Arming/Disarming OptionsOption [1] OFF = Regular Arming Switches to Force Arming Disabled Option [1] ON = Regular Arming Switches to Force Arming Enabled (default)With this feature enabled, the control panel will always Force arm (if a force-enabled zone is open, see Force Zones on page 22) instead of Regular arm when a valid user access code with the Force Arming Option is entered. 10.4 Stay Arming switches to Stay Force Arming(Not to be used with UL Installations)Section [704]: Arming/Disarming OptionsOption [2] OFF = Stay Arming Switches to Stay Force Arming Disabled Option [2] ON = Stay Arming Switches to Stay Force Arming Enabled (default)With this feature enabled, the control panel will always Stay Force arm (if a force-enabled zone is open, see Force Zones on page 22) instead of Stay arm when a valid user access code with the Force Arming Option is entered. 10.5 Sleep Arming switches to Sleep Force Arming(Not to be used with UL Installations)Section [704]: Arming/Disarming OptionsOption [3] OFF = Sleep Arming Switches to Sleep Force Arming Disabled Option [3] ON = Sleep Arming Switches to Sleep Force Arming Enabled (default)With this feature enabled, the control panel will always Sleep Force arm (if a force-enabled zone is open, see Force Zones on page 22) instead of Sleep arm when a valid user access code with the Force Arming Option is entered. 10.6 Restrict Arming on Battery FailureSection [703]: Arming/Disarming OptionsOption [5] OFF = Permit arming on battery failure (default)Option [5] ON = Restrict arming on battery failureIf this option is enabled, the control panel will not arm the system if the control panel detects that the backup battery is disconnected, that its fuse is blown, or that the battery voltage drops to less than 10.5V. The control panel will not arm the system until all battery trouble conditions are rectified. 10.7 Restrict Arming on Tamper FailureSection [703]: Arming/Disarming OptionsOption [6] OFF = Permit arming on tamper failure (default)Option [6] ON = Restrict arming on tamper failureIf this option is enabled, the control panel will not arm the system if the control panel detects a tamper trouble on one or more zones. The control panel will not arm the system until all tamper trouble conditions are rectified. This feature will not function if the tamper recognition options (see Tamper Recognition on page 36) are disabled or whenever the tampered zone is bypassed and the tamper bypass options have been enabled (see Tamper Bypass Options on page 37).](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-36.png)
![Magellan 3310.8 Restrict Arming on Wireless Supervision TroubleSection [703]: Arming/Disarming OptionsOption [7] OFF = Permit arming on wireless supervision failure (default)Option [7] ON = Restrict arming on wireless supervision failureIf this option is enabled, the control panel will not arm the system if the control panel detects a wireless supervision trouble on one or more zones. The control panel will not arm the system until all wireless supervision trouble conditions are rectified. This feature will not function if the tamper recognition options (see Tamper Recognition on page 36) are disabled or whenever the tampered zone is bypassed and the tamper bypass options have been enabled (see Tamper Bypass Options on page 37).10.9 Arm/Disarm with VDMP3Section [703]: Arming/Disarming OptionsOption [8] OFF = Arm/Disarm with VDMP3 disabledOption [8] ON = Arm/Disarm with VDMP3 enabled (default)If this option is enabled, arming/disarming with the VDMP3 is functional. Disable the option if you do not want the ability to arm/disarm the system via telephone. 10.10 Timed Auto-ArmingSection [741] = Partition 1, [742] = Partition 2 Option [1] OFF = Timed Auto-Arming Disabled (default)Option [1] ON = Timed Auto-Arming EnabledEach partition can be programmed to arm every day at the time specified by the Auto-arm Timer. The auto-arming options (see Auto-Arming Options on page 34) determine the partition's arming method. Any open zones detected when a partition is auto-armed will be bypassed regardless of their definition (except 24Hr zones). The control panel will enter a 60-second exit delay period before arming the system. At this point, auto-arming can be cancelled by entering a valid access code. Once the partition has successfully armed, the control panel can transmit the Timed Auto-arming report code programmed in section [860]. Example: To automatically arm partition 2 everyday at 6:15PM, enable Timed Auto-arming for partition 2 by turning on option [1] in section [742]. Then key in 18:15 into section [762].10.10.1 Auto-Arm TimerSection [761] = Partition 1, [762] = Partition 2 Select the section corresponding to the desired partition and program the time (use the 24-hour clock i.e. 6:30PM = 18:30) that you wish the control panel to attempt to arm the selected partition and/or send the Late to Close report code. 10.11 No Movement Auto-ArmingSection [741] = Partition 1, [742] = Partition 2 Option [2] OFF = No Movement Auto-Arming Disabled (default)Option [2] ON = No Movement Auto-Arming EnabledIf no movement occurs in a partition's protected area for the period specified by the No Movement Timer, the control panel can automatically arm that partition. The Auto-arming Option determines the partition's arming method. Any open zones detected when a partition is Auto-armed will be bypassed regardless of their definition (except 24Hr zones). Upon arming, the control panel will transmit the No Movement report code if programmed in section [860]. Regardless of whether the system was successfully armed or not, the control panel will always transmit the No Movement report code if programmed in section [860]. If No Movement Auto-arming is disabled, the control panel will still send the No Movement report code at the time specified by the No Movement Timer. Example: To arm partition 1 whenever there is no movement for a period of 4 hours, enable No Movement Auto-arming for partition 1 by turning on the [2] Option in section [741]. Then in section [749] enter 016 (16x15min = 240min = 4 hours). 10.11.1 No Movement TimerSection [749] = Partition 1, [750] = Partition 2 000 to 255 x 15 min, Default = Disabled Select the section corresponding to the desired partition and program the interval of time without movement you wish the control panel to wait before arming and/or sending the No Movement report code. If No Movement Auto-arming is disabled, the control panel can still send the No Movement report code when no movement has been detected for the period specified by the No Movement Timer.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-37.png)
![34 Reference & Installation Manual 10.12 Auto-Arming Options (Not to be used with UL installations)Section [741] = Partition 1, [742] = Partition 2 When using Timed Auto-arming or No Movement Auto-arming, the control panel can Regular, Sleep or Stay arm the selected partition. 10.13 One-Touch Arming (Not to be used with UL installations)Section [703]: Options [1] to [3]Option [1] ON = Press & hold the [ARM] key for One-touch Regular Arming.Option [2] ON = Press & hold the [STAY] key for One-touch Stay Arming. Option [3] ON = Press & hold the [SLEEP] key for One-touch Sleep Arming.The One-touch arming features allow users to arm the system without having to enter any access codes. To arm the system, press and hold the appropriate key (see above) for approximately 3 seconds. If the system is partitioned, you must also press the key corresponding to the partition you wish to arm. 10.14 One-Touch Bypass Programming (Not to be used with UL installations)Section [703]: Options [4]Option [4] ON = Press & hold the [BYP] key for One-touch Bypass Programming.Bypass programming allows users to program the alarm system to ignore (deactivate) specified zones the next time the system is armed. Press and hold the [BYP] key for three seconds to access bypass programming mode.10.15 Exit DelaySection [745] = Partition 1, [746] = Partition 2 001 to 255 seconds, Default = 60 seconds, Maximum 60 seconds for UL Listed systems After entering the required arming sequence (i.e. user access code, etc.), the exit delay parameter determines the amount of time a user has to leave the protected area before the control panel arms the partition. The exit delay applies to all zones in the selected partition. When enabled, the keypad will beep once every second during the exit delay and will beep rapidly during the final 10 seconds of the exit delay. 10.15.1 Beep On Exit DelaySection [704]: Arming/Disarming OptionsOption [6] OFF = Beep on Exit Delay Disabled Option [6] ON = Beep on Exit Delay Enabled (default)10.16 Bell Squawk On Arm/Disarm with KeypadSection [704]: Arming/Disarming OptionsOption [5] OFF = Bell Squawk on Arm/Disarm Disabled (default)Option [5] ON = Bell Squawk on Arm/Disarm EnabledWhen this feature is enabled, the bell or siren will squawk once upon arming and twice upon disarming via the keypad.10.17 Bell Squawk On Arm/Disarm with Remote ControlSection [704]: Arming/Disarming OptionsOption [4] OFF = Bell Squawk on Arm/Disarm with Remote Control Disabled (default)Option [4] ON = Bell Squawk on Arm/Disarm with Remote Control EnabledWhen this feature is enabled, the bell or siren will squawk once upon arming with a remote control and twice upon disarming with a remote control. Must be enabled for UL installations.10.18 No Exit Delay When Arming with Remote ControlSection [704]: Arming/Disarming OptionsOption [8] OFF = Provides Exit Delay When Arming with a Remote Control (default)Option [8] ON = No Exit Delay When Arming with a Remote ControlWhen the option is enabled, the panel cancels the exit delay (arms instantly) when a partition is armed with a remote control. When disabled, the exit delay timer will start when a partition is armed with a remote control. [3] [4]OFF OFF RegularOFF ON SleepON OFF Stay](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-38.png)
![Magellan 3510.19 No Exit Delay Beeps and No Bell Squawk When Stay/Sleep ArmingSection [704]: Arming/Disarming OptionsOption [7] OFF = No Exit Delay Beeps and No Bell Squawk When Stay/Sleep Arming Disabled Option [7] ON = No Exit Delay Beeps and No Bell Squawk When Stay/Sleep Arming Enabled (default)With this feature enabled, the control panel will prevent the bell or siren from squawking and the keypads from beeping during the exit delay, whenever a partition is Stay/Sleep armed. 10.20 Exit Delay TerminationSection [700]: Arming/Disarming OptionsOption [6] OFF = Exit Delay Termination (Disabled) Option [6] ON = Exit Delay Termination Enabled (default)When option [6] is enabled (ON), the panel will reduce the Exit Delay to 10 seconds when an Entry Delay zone is opened and closed during the Exit Delay.Example: 15 seconds into a 45 second Exit Delay, an Entry Delay zone opens and closes. The remaining 30 seconds is reduced to 10 seconds. 10.21 Fast ExitWhen the system is already Stay or Sleep armed: This feature will allow you to exit and keep the system armed. Press and hold the [OFF] key for 3 seconds to start the exit delay. After the exit delay has elapsed, the system will switch to its previous arming mode.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-39.png)
![36 Reference & Installation Manual Part 11: Alarm Options11.1 Bell Cut-Off TimerSection [747] = Partition 1, [748] = Partition 2 000 = Disabled, 001 to 255 minutes, Default = 4 minutes, 5 minutes minimum for ULC installationsAfter an audible alarm, the bell or siren will stop upon disarming of the partition or when the Bell Cut-Off Timer has elapsed, whichever comes first. 11.2 Recycle AlarmAfter the Bell Cut-Off Timer and the Recycle Delay have elapsed, the control panel will re-verify the zone status. If there are any open zones, the control panel will generate another alarm. In one armed period, the control panel will repeat this sequence the number of times defined by the Recycle Counter. 11.2.1 Recycle Alarm DelaySection [714] 000 = disabled, 001 to 255 minutes, Default = DisabledThe Recycle Delay determines the amount of time after Bell Cut-Off that the control panel will wait before re-verifying zone status. 11.2.2 Recycle Alarm CounterSection [715] 000 = disabled, 001 to 255, Default = Disabled The Recycle Counter determines the number of times the control panel will re-verify the zone status after Bell Cut-Off in one armed period. 11.3 Tamper Recognition 11.3.1 Zones/RF Module and Keypad/Bus Module Tamper RecognitionSection [705]: Tamper Recognition Options If a device has been tampered with (i.e. the anti-tamper switch has been set off), the control panel can generate a trouble, an alarm, and/or transmit a report code to the monitoring station. The system will react to an RF zone and a keypad/bus module differently.11.4 RF Module SupervisionSection [705]: Supervision OptionsThe control panel waits for each of its assigned wireless transmitters to send a status signal within a specified time period to confirm their presence and functionality. If a device has not sent a signal within that time period, the control panel can generate a trouble, an alarm, and/or transmit a report code to the monitoring station. The system will react to an RF zone and a keypad/bus module differently.[3] [4] Zones/RF Module Tamper Recognition Options Keypad / Bus Module Tamper Recognition Options*OFF OFF Disabled DISABLEDOFF ON TROUBLE ONLY TROUBLE ONLYON OFF When disarmed: TROUBLE ONLYWhen armed: Follow zone’s alarm typeTROUBLE ONLYON ON When disarmed: AUDIBLE ALARMWhen armed: Follow zone’s alarm typeAUDIBLE ALARM* Tamper recognition of keypad/bus module only if section [700] option [7] is enabled.[6] [7] RF Supervision Options Keypad / Bus Module Supervision OptionsOFF OFF Disabled Disabled OFF ON TROUBLE ONLY TROUBLE ONLYON OFF When disarmed: TROUBLE ONLYWhen armed: Follow zone’s alarm typeTROUBLE ONLYON ON When disarmed: AUDIBLE ALARMWhen armed: Follow zone’s alarm typeAUDIBLE ALARM](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-40.png)
![Magellan 3711.5 Tamper Bypass OptionsSection [705]: Zone OptionsOption [5] OFF = Tampers on bypassed zones will be ignoredOption [5] ON = Will generate a tamper if detected on a bypassed zone (default) With option [5] off, the Tamper Recognition feature follows the zone bypass definition. This means the control panel will ignore any tampers detected on a bypassed zone. With option [5] on, Tamper Recognition ignores the bypass definition. This means the control panel will generate an incident as per Tamper Recognition settings if a tamper or wire fault occurs on a bypassed zone. 11.6 Tamper Supervision on the Bus ModuleSection [700]: Supervision OptionsOption [7] OFF = Tamper supervision disabled (default)Option [7] ON = Tamper supervision enabledWhen the control panel detects a tamper on a bus module, the control panel can generate an alarm or trouble, unless the Tamper Supervision is disabled.11.7 Keypad Panic OptionsSection [702]: General OptionsOption [1] OFF = Panic 1 Disabled (default)Option [1] ON = Panic 1 EnabledPressing the [1] and [3] keys simultaneously on the keypad for 3 seconds will generate a silent or audible alarm as defined by option [4].Option [2] OFF = Panic 2 Disabled (default)Option [2] ON = Panic 2 EnabledPressing the [4] and [6] keys simultaneously on the keypad for 3 seconds will generate a silent or audible alarm as defined by option [5].Option [3] OFF = Panic 3 Disabled (default)Option [3] ON = Panic 3 EnabledPressing the [7] and [9] keys simultaneously on the keypad for 3 seconds will generate a silent or audible alarm as defined by option [6].Option [4] OFF = Panic 1 is Silent (default)Option [4] ON = Panic 1 is AudibleOption [5] OFF = Panic 2 is Silent (default)Option [5] ON = Panic 2 is AudibleOption [6] OFF = Panic 3 is Silent (default)Option [6] ON = Panic 3 is AudibleSilent alarm:The control panel emits a confirmation beep and transmits the appropriate Panic report code if programmed in section [863]. The control panel will not enable the keypad buzzers or the control panel’s BELL output (no audible alarm). Audible alarm:Same as silent alarm, except the keypad buzzers and the BELL output will activate until a user cancels the alarm (disarms) with a valid user access code or when the Bell Cut-Off Timer elapses (see Bell Cut-Off Timer on page 36).Whether the system is partitioned or not, the control panel will report all panic alarms to partition 1.11.8 Panic Lockout TimerSection [718]When a panic alarm is activated, the control panel can ignore the disarm signal from a remote control for a specified period. This prevents an aggressor from disarming the system by remote control during a panic situation. In section [718] enter a 3-digit value (000 to 255, 000 = disabled) representing the number of seconds that the remote controls will be locked out of the system.11.9 Flex-Instant DelaySection [720]The Flex-Instant Delay is used to prevent false alarms when the premises is Stay/Sleep armed. In section [720] enter a 3-digit value (000 to 255, 000 = disabled) representing the number of seconds that the panel will delay an alarm allowing you to disarm the system (default 15 seconds).](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-41.png)
![38 Reference & Installation Manual Part 12: Reporting and Dialer settingsThe following section explains all the features and options that must be programmed in order for your security system to properly report system events to a monitoring station. When an event (e.g. zone in alarm) occurs in the system, the control panel verifies if a report code was programmed in the section corresponding to the event (except Ademco Contact ID “All Codes”). If a report code was programmed, the control panel will dial the monitoring station telephone number defined by the Event Call Direction feature. When the monitoring station answers, the control panel will transmit the System Account Code, followed by the programmed report code.12.1 Zone Reporting CodesSections [141] to [172]A report code can be programmed for each of the available 32 zones. When an alarm, alarm restore, tamper, or tamper restore occurs on a zone, the control panel can send the appropriate report code to the monitoring station. 12.2 User Reporting CodesSections [471] to [502]A report code can be programmed for each of the available 32 users. When a user arms, disarms or cancels an alarm, the control panel can send the appropriate report code to the monitoring station. 12.3 Special Arming Report CodesSections [860] and [861]When the system is armed using one of the special arming features listed below, the control panel can send the appropriatereport code to the monitoring station identifying how the system was armed.Section [860]•Auto-Arming: A partition has armed itself at the programmed time. •Late to Close: Reports every day at the time specified by the Auto-arm Timer. •No Movement: No movement has been detected for the programmed amount of time in the partition.•Partial Arming: A partition was Stay, Sleep, or Force armed or armed with Bypassed zones.Section [861]•Quick Arming: A partition was armed using a One-touch arming feature.•Arming via PC: A partition was armed using the Winload software. •N/A•N/A12.4 Special Disarming Report CodesSection [862]When using one of the special disarming features, the control panel can send the report code to the monitoring station, identifying how the system was disarmed.•Cancel Auto-Arm: A partition is disarmed during the Timed Auto-arm's 60-second exit delay. Only reports if Disarming Reporting Options are set to always report disarming. •Disarming via PC: System is disarmed using the WinLoad software. Only reports if Disarming Reporting Options are set to always report disarming. •Cancel alarm with user or WinLoad: An alarm is cancelled using the WinLoad software. •Cancel Paramedic Alarm: A paramedic alarm is cancelled. 12.5 Special Alarm Report CodesSections [863] and [864]When the system generates an alarm due to one of the conditions listed below, the control panel can send the appropriate reportcode to the monitoring station identifying the type of alarm.Section [863]•Emergency Panic: Panic keys [1] and [3] have been pressed.•Auxiliary Panic: Panic keys [4] and [6] have been pressed.•Fire Panic: Panic keys [7] and [9] have been pressed.•Recent Closing: Reports when an alarm is generated after arming the system within period defined by the Recent Close Delay.Section [864]•Zone Shutdown: A zone communicates more than the programmed number of transmissions in a single armed period. •Duress: A Duress access code is keyed in. •Keypad Lockout: If a consecutive number of invalid codes are entered into a keypad, the control panel can be set to deny access from all keypads for a specified period.•Paramedic Alarm: A parademic alarm is sent to the monitoring station.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-42.png)
![Magellan 3912.6 System Trouble Report CodesSection [865] to [869]When the system generates one of the instances listed below, the control panel can send the appropriate report code to the monitoring station identifying the type of system trouble.Section [865]•N/A•AC Failure: The control panel has detected a loss of AC power. Transmission of this report code can be delayed.•Battery Failure: Backup battery is disconnected or battery voltage is low.•Auxiliary Supply: Auxiliary power supply has overloaded.Section [866]•Bell Output Overload: Bell/siren output has overloaded.•Bell Output Disconnected: Devices connected to the Bell Output have been disconnected.•Timer Loss: The control panel has detected a loss in time or clock failure.•Fire Loop Trouble: The control panel has detected a tamper trouble on a fire zone. Section [867]•Fail To Communicate: The control panel has failed all attempts to communicate with the monitoring station. The report code will be transmitted upon the next successful attempt.•RF Interference: Will report if the RF signal is being jammed.•Module Lost: The control panel has failed to communicate with one or more modules (including keypads).•Module Tamper: The anti-tamper switch of a module (including keypads) has been triggered. Section [868]•Module AC Fail: The AC voltage of a module has dropped below recommended limits. •Module Low/No Battery: The battery voltage of a module has dropped below recommended limits.•Wireless Zone Low Battery: The battery voltage of a wireless transmitter has dropped below recommended limits.•Wireless Zone Supervision Lost: The control panel has lost communication with a wireless zone.Section [869]•Wireless PGM Supervision Lost: The control panel has lost communication with a wireless PGM.•Wireless PGM Tamper: The anti-tamper switch of a wireless PGM has been triggered.•N/A•N/A12.7 System Trouble Restore Report CodesSections [870] to [874]When the system restores one of the troubles listed in System Trouble Report Codes above, the control panel can send the appropriate report code to the monitoring station identifying the type of system trouble restore. If Telephone Line Monitoring is enabled, the control panel can also transmit a TLM Restore report code.12.8 System Special Report CodesSections [875] to [876]When the system generates one of the instances listed below, the control panel can send the appropriate report code to the monitoring station identifying the type of system occurrence.Section [875]•Cold Start: The control panel was completely shutdown (no battery, no AC) and then was re-started.•Test Report: A test report has been generated automatically.•WinLoad In: The control panel has commenced communication with WinLoad.•WinLoad Out: The control panel has ended communication with WinLoad.Section [876]•Installer In: Installer/Maintenance has entered the programming mode.•Installer Out: Installer has exited the programming mode.•Closing Delinquency: The control panel will send a Closing Delinquency report code if the system has not been armed within a programmed amount of days.•N/A12.9 Clear Reporting CodesSection [966]: Clear Reporting CodesOption [1] OFF = Clear zone reporting codes Option [1] ON = Clear zone reporting codes (default)Option [2] OFF = Clear user reporting codes Option [2] ON = Clear user reporting codes (default)Option [3] OFF = Clear arm/disarm/alarm reporting codes](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-43.png)
![40 Reference & Installation Manual Option [3] ON = Clear arm/disarm/alarm reporting codes (default)Option [4] OFF = Clear trouble reporting codes Option [4] ON = Clear trouble reporting codes (default)Enable all options you want to clear. The respective sets of reporting codes will be cleared after exiting the section.12.10 Reset Reporting CodesSection [967]: Reset Reporting CodesOption [1] OFF = Reset zone reporting codes Option [1] ON = Reset zone reporting codes (default)Option [2] OFF = Reset user reporting codes Option [2] ON = Reset user reporting codes (default)Option [3] OFF = Reset arm/disarm/alarm reporting codes Option [3] ON = Reset arm/disarm/alarm reporting codes (default)Option [4] OFF = Reset trouble reporting codes Option [4] ON = Reset trouble reporting codes (default)Enable all options you want to reset to default. The respective sets of reporting codes will be reset after exiting the section.12.11 Monitoring Station Telephone NumbersSection [815] = Phone#1, [816] = Phone#2, [817] = Backup Phone#, [818] = Pager #, [819] = Numeric Message Sent with Pager Reporting: Up to 32 digits The control panel can dial up to 2 different monitoring station telephone numbers. You can enter any digit from 0 to 9 and any special keys or functions (see Table 5 on page 40) up to a maximum of 32 digits. After the maximum dialing attempts (see Maximum Dialing Attempts on page 42) to one monitoring station telephone number have failed, the control panel will then dial the backup telephone number. If the Alternate Dial Option (see Alternate Dial Option on page 42) is enabled, the control panel will dial the programmed backup telephone number after every failed attempt. If no backup telephone number is programmed, the control panel will never report to the backup telephone number. Also see Delay Between Dialing Attempts on page 42.12.12 Personal Dialing NumbersPersonal Dialing numbers are personal numbers (e.g. cellular, office) that the panel can call in case of an alarm or panic. To program these five numbers see the Communicator Menu in either the Master or User Quick Menu. To set the call parameters, see options [5], [6], and [7] of section [804]. The panel will call these personal numbers if programmed in the event of any panic or alarm (default) and sound a bell tone. To program the delay between the call attempts, see section [832]. The panel can also be programmed to delay before sounding the bell tone, which can be programmed in section [836].The default delay is 20 seconds. To determine the length of time the bell tone sounds on the phone line, see section [837]. The default value is 003, meaning the 10 second bell tone will repeat itself 3 times after the initial sequence (total= 40 seconds). 12.13 Reporting FormatsSection [810]: 1st digit = Format for Phone #1, 2nd digit = Format for Phone #2The panel can use a number of different reporting formats and each monitoring station telephone number can be programmed with a different reporting format. The first digit entered into section [810] represents the reporting format used to communicate with Monitoring Station Telephone Number 1, the second digit represents the reporting format used to communicate with Monitoring Station Telephone Number 2. The Backup Telephone Number uses the same reporting format as the last monitoring station telephone number that was dialed.Table 5: Special Keys for Telephone NumbersPress Action or Value[OFF]*[BYP]#[MEM]switch from pulse to tone dialing or vice versa[TBL] 4-second pause[SLEEP]deletes current digit[] inserts blank space](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-44.png)
![Magellan 41 If Hexadecimals (0 to FF) are used to program the report codes, verify that the pager also supports Hexadecimals. If the pager does not support Hexadecimals, use only the digits 0 to 9.UL Note: The installer is required to verify the complete compatibility of the DAC Receiver and formats at least once per year.12.13.1 Standard Pulse FormatsThe control panel can use the Ademco slow, Silent Knight and Sescoa standard pulse reporting formats which will transmit the 2-digit (00 to FF) report codes programmed into sections [860] to [876]. (see Table 6 on page 41).12.13.2 Ademco ExpressThe Ademco Express is a high-speed reporting format, which will transmit the 2-digit (00 to FF) report codes programmed into sections [860] to [876]. 12.13.3 Ademco Contact IDAdemco Contact ID is a fast communicator format that uses tone reporting instead of pulse reporting. This communicator format also uses a pre-defined list of industry standard messages and report codes that will suit most of your basic installation needs. Please refer to the Contact ID Report Codes List in the Programming Guide for a complete list of these report codes and messages. If the reporting codes are set at 0xFF, the panel will send the appropriate report code from the Automatic Report Code List in the programming guide. Alternatively, report codes can be programmed using the Ademco Contact ID Report Codes in the programming guide.12.13.4 Event Call DirectionSection [802]: Options [1] to [3]; Arming/DisarmingOption [1] ON =Call MSTN 1Option [2] ON =Call MSTN 2Option [3] ON =Call Pager telephone numberSection [802]: Options [5] to [7]; Alarm/Alarm RestoreOption [5] ON =Call MSTN 1Option [6] ON =Call MSTN 2Option [7] ON =Call Pager telephone numberSection [803]: Options [1] to [3]; Tamper/Tamper RestoreOption [1] ON =Call MSTN 1Option [2] ON =Call MSTN 2Option [3] ON =Call Pager telephone numberSection [803]: Options [5] to [7]; Trouble/Trouble RestoreOption [5] ON =Call MSTN 1Option [6] ON =Call MSTN 2Option [7] ON =Call Pager telephone numberSection [804]: Options [1] to [3]; Special ReportingOption [1] ON =Call MSTN 1Option [2] ON =Call MSTN 2Option [3] ON =Call Pager telephone numberSection [804]: Options [5] to [7]; Special ReportingOption [1] ON =Call voice on zone alarm (burglary/fire)Option [2] ON =Call voice on panic alarmsOption [3] ON =Call voice on paramedic alarmThe events are divided into six groups (see above) where each event group can be programmed to dial up to three telephone numbers (MSTN 1 & 2 and the Pager telephone number).Table 6: Reporting FormatsValue Entered Reporting Format 0 Ademco Slow (1400Hz, 1900Hz, 10BPS)1 Silent Knight Fast (1400Hz, 1900Hz, 10BPS)2 SESCOA (2300Hz, 1800Hz, 20BPS)3 Ademco Express (DTMF 4+2)4 Ademco Contact ID 5SIA](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-45.png)
![42 Reference & Installation Manual When a reportable event occurs in the system, the panel will begin dialing the numbers sequentially starting from MSTN 1 (if enabled), skipping any disabled numbers and stopping once all selected telephone numbers have been called. After a certain amount of failed attempts (section [831]) at trying to call the monitoring station, the control panel will then dial the selected backup telephone number (if enabled; see Programming Guide). If the Alternate Dial option is enabled, the control panel will dial the programmed backup telephone number (if enabled) after every failed attempt. If no backup telephone number is programmed, the control panel will never report to the backup telephone number. Example: The system is armed and zone 1 has been breached causing an alarm. If options [5] and [7] are OFF and option [6] is ON in section [802], the control panel will attempt to communicate with MSTN 2.12.13.5 Account Numbers Section [811]: Partition 1, Section [812]: Partition 2All report codes are preceded by a 4-digit or 3-digit Partition Account Number to ensure correct identification in a partitioned system. Partition account numbers can be any hexa-digit from 1 to F. To enter a 3-digit account number, simply press the [SLEEP] key followed by a 3-digit account number. Also, when using 3-digit account numbers, you must use 1-digit report codes. 12.14 Dialing MethodSection [800]: Dialer OptionsOption [6] OFF = Pulse Dialing (see Pulse Ratio on page 42).Option [6] ON = Tone/DTMF Dialing (default)12.15 Pulse RatioSection [800]: Dialer OptionsOption [7] OFF = European Pulse Ratio of 1:2 Option [7] ON = U.S.A. Pulse Ratio of 1:1.5 (default)When using Pulse dialing, you can select one of two Pulse Ratios. Although most European countries use the 1:2 pulse ratio, the 1:1.5 ratio may provide better results in some cases. The same applies for North American countries. If the 1:1.5 pulse ratio is not providing the desired results, the 1:2 ratio may be used.12.16 Maximum Dialing AttemptsSection [831] 000 to 255 attempts, Default = 8 attemptsThe value programmed in section [081] determines how many times the control panel will re-dial the same monitoring station telephone number before proceeding to the next number. 12.17 Maximum Dialing Attempts - VDMP3Section [841]000 to 255 attempts, Default = 8 attemptsThe value programmed in section [841] determines how many times the control panel will re-dial the same telephone number before proceeding to the next number. The maximum dialing attempts programmed in this section is independent from those programmed in section [831] of the panel dialer used for monitoring station reporting. 12.18 Delay Between Dialing AttemptsSection [832] 000 to 255 seconds, Default = 20 seconds This delay determines the amount of time the control panel will wait between each dialing attempt. This section applies to the Plug-in Voice Dialer when using a VDMP3.12.19 Switch to Pulse on 5th AttemptSection [800] Option [3] OFF = Switch to Pulse on 5th Attempt Disabled (default)Option [3] ON = Switch to Pulse on 5th Attempt EnabledWith option [3] ON, the control panel will switch to pulse dialing on the 5th attempt of reaching the monitoring station. 12.20 Alternate Dial OptionSection [800]: Dialer OptionsOption [4] OFF = Alternate Dial Disabled (default)Option [4] ON = Alternate Dial EnabledWith option [4] OFF, the control panel will dial the backup programmed in section [817] after all attempts to one monitoring station number have failed. With option [4] ON, the control panel will dial the backup number after every failed attempt.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-46.png)
![Magellan 4312.21 Force Dial OptionSection [800]: Dialer OptionsOption [5] OFF = Force Dial Disabled Option [5] ON = Force Dial Enabled (default)With option [5] is enabled, the panel will dial a telephone number even if no dial tone is present after 4 seconds.12.22 Recent Closing DelaySection [838] 000 = Disabled, 001 to 255 seconds, Default = Disabled If after having armed the system, an alarm is generated within the period defined by the Recent Close Delay, the control panel will attempt to transmit the Recent Close report code programmed in section [863]. 12.23 Auto Test ReportSections [840] 000 = Disabled, 001 to 255 days, Default = Disabled Section [850]: Time (HH:MM)The control panel will transmit the Test Report report code programmed into section [875] after the number of days programmed into section [840] has elapsed at the time programmed into section [850]. Use the 24-hour clock to program the time (i.e. 6:30PM = 18:30). The first Test Report will be transmitted within 24 hours after the feature is enabled at the time programmed in [850]. Example: Section [840] = 005 and section [850] = 13:00. The first Test Report will be sent at 1 PM that day and then the report will be sent every 5 days at 1 PM.12.23.1 Auto Test Report Transmission OptionsSections [800] 12.23.2 Armed Report DelaySection [851] 000 = disabled, 001 to 255 minutes, Default = 5 min.The Armed Report Delay determines the amount of time after an Arming event that the control panel will wait before sending a report. 12.23.3 Disarmed Report DelaySection [852] 000 = disabled, 001 to 255 minutes, Default = 60 min.The Disarmed Report Delay determines the amount of time after an Disarming event that the control panel will wait before sending a report. 12.24 Closing Delinquency DelaySection [719]000 = Disabled, 001 to 255 days, Default = DisabledAt midnight every day, the control panel will verify when the partition was last disarmed. If the partition has not been armed within the time programmed in the Closing Delinquency Delay, the control panel will transmit a Closing Delinquency event to the monitoring station.Example: The Closing Delinquency Timer for partition 1 in section [719] is programmed for 005 days. The control panel verifies when partition 1 was last disarmed at midnight every day. If partition 1 was not armed within the last 5 days, the panel will transmit a Closing Delinquency event to the monitoring station. The Closing Delinquency Event and timer apply only to partition 1.[3] [4] Auto-Test Report Transmission OptionsOFF OFF Transmit the test report code every time the days programmed in section [840] have elapsed at the time programmed in section [850] (default). OFF ON When disarmed: Transmit test report code every time the time programmed in section [852] has elapsed. When armed: Transmit test report code every time the time programmed in section [851] has elapsed. ON OFF The control panel will transmit the test report code every hour on the minute value programmed in section [850] (the last two digits). Note that the first two digits of section [850] will be ignored. E.g. If 10:25 was programmed into section [850], the test report code would be transmitted at the 25th minute of every hour, i.e. 11:25, 12:25, etc.ON ON The test report code will be transmitted when any of the conditions of the second and third options listed above (options [3] = OFF and [4] = ON / options [3] = ON and [4] = OFF) are met.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-47.png)
![44 Reference & Installation Manual 12.25 Power Failure Report DelaySection [839] 001 to 255 minutes, Default = 15 minutesThe control panel will transmit the AC Failure report code programmed in section [865] after the Power Failure Report Delay period has elapsed. 12.26 Report System Disarming Section [801]: Arming /Disarming OptionsOption [1] OFF = Always Report DisarmingOption [1] ON = Report Disarming Only After Alarm (default)With option [1] OFF, the control panel will send the Disarming report codes (see Special Disarming Report Codes on page 38) to the monitoring station every time the system is disarmed. With option [1] ON, the control panel will send the Disarming report codes to the monitoring station when the system is disarmed following an alarm.12.27 Zone Restore Report OptionsSection [801]: Zone OptionsOption [2] OFF = Report On Bell Cut-Off (default)Option [2] ON = Report On Zone ClosureWith option [2] OFF, the panel will send the Zone Alarm Restore report codes to the monitoring station when the zone has returned to normal and the Bell Cut-Off Timer has elapsed. With option [2] ON, the panel will send the Zone Alarm Restore report codes to the monitoring station as soon as the zone returns to normal or when the system is disarmed. 12.28 Telephone Line Monitoring (TLM) When enabled, the system verifies the existence of a telephone line once every second. A line test failure occurs when the TLM detects less than 3 volts for the period defined by the TLM Fail Timer. If the line test fails, the control panel’s STATUS LED flashes and generates one or more conditions as defined by the TLM settings below. These will be restored when the control panel detects the telephone line again. Please note that when the dialer detects an incoming call, the TLM test will stop for 1 minute.Section [800]: Dialer Options [1] OFF / [2] OFF: TLM Disabled[1] OFF / [2] ON: Trouble OnlyUpon line test failure, a TLM Trouble will appear in the keypad’s trouble display (see Trouble Display on page 53).[1] ON / [2] OFF: Audible Alarm If System Armed Upon line test failure, a TLM Trouble will appear in the keypad’s trouble display (see Trouble Display on page 53) and if the system is armed, the control panel will generate an audible alarm.[1] ON / [2] ON: Silent Alarm Becomes Audible Upon line test failure, a TLM Trouble will appear in the keypad’s trouble display (see Trouble Display on page 53) and causes a silent zone or silent panic alarm to switch to audible.12.28.1 TLM Fail TimerSection [830] 016 to 255 x 2 seconds, Default = 32 secondsIf TLM does not detect the existence of a telephone line for the duration of this period, the control panel will generate the condition(s) defined by the TLM options.12.29 Pager Reporting Delay Section [834]: Communication Timers000 to 255 seconds, Default = 20 secondsWhen using the Pager Reporting Format, the control panel will wait for the Pager Delay period before transmitting the report codes. This is to allow time for the pager system to provide a dial tone or to bypass the “welcome” message before sending data.12.30 Pager Reporting Message Repetition Section [835]: Communication Timers000 to 255 times, Max. 10, Default = 3When using the Pager Reporting Format, the control panel will repeatedly send the report codes to the pager until the transmission has been acknowledged.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-48.png)
![Magellan 4512.31 Personal Reporting Delay Section [836]: Communication Timers000 to 255 times, Max. 127, Default = 5When using the Personal Reporting Format, the control panel will wait for the Personal Delay period before transmitting the report codes. This is to allow time for the system to provide a dial tone or to bypass the “welcome” message before sending data. This section applies to the Plug-in Voice Dialer when using a VDMP3.12.32 Personal Reporting Message Repetition Section [837]: Communication Timers000 to 255 times, Max. 10, Default = 3When using the Personal Reporting Format, the control panel will repeatedly send the report codes to the pager until the transmission has been acknowledged. This section applies to the Plug-in Voice Dialer when using a VDMP3.12.33 Disable ReportingSections [800] Option [1] OFF = Dialer Activated (default)Option [1] ON = No DialerWith this option disabled (default), the control panel will continue to report events. With the option enabled, reporting is disabled.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-49.png)
![46 Reference & Installation Manual Part 13: Programmable OutputsA PGM is a programmable output that toggles to its opposite state (i.e. a normally open PGM will close) when a specific event has occurred in the system. For example, a PGM can be used to activate bells or strobe lights, open/close garage doors and much more. When a PGM activates, the control panel triggers any device or relay connected to it. The control panel includes two/four onboard PGMs. It can support up to a total of 16 PGMs. A Wireless PGM module can be assigned to any PGM. It will work in parallel with the Control Panel Output.13.1PGM Activation EventSections [220], [222], [224], [226], [228], [230], [232], [234], [236], [238], [240], [242], [244],[246], [248], and [250]This feature allows you to program the control panel to activate a PGM when a specific event occurs in the system. The PGM will remain in its active state until the programmed PGM Deactivation Event occurs or when the PGM Delay period elapses. For the Event List see the programming guide. To program a PGM Activation Event:1) Enter section that represents the desired PGM. PGM1 = [220], PGM2 = [222], etc. 2) Enter the Event Group #. 3) Enter the Sub-Group #. 4) Enter the Partition # (01 = Partition 1 02 = Partition 2 99 = Both Partitions) The “AC Loss” PGM Event will only occur after the power failure report delay elapses (see Power Failure Report Delay on page 44).13.2 PGM Deactivation EventSections [221], [223], [225], [227], [229], [231], [233], [235], [237], [239], [241], [243], [245],[247], [249], and [251]After PGM activation, the PGM will return to its normal state (deactivate) when the programmed PGM Deactivation Event occurs. Instead of deactivating the PGM when a specific event occurs, the PGM can deactivate after a programmed period elapses (see PGM Delay on page 46). For the Event List see the Programming Guide. If using the PGM Delay, these sections can be used as a second activation event.1) Enter section that represents the desired PGM. PGM1 = [221], PGM2 = [223], etc.2) Enter the Event Group #. 3) Enter the Sub-Group #. 4) Enter the Partition # (01 = Partition 1 02 = Partition 2 99 = Both Partitions) 13.3 PGM Delay Section [281] = PGM 1 to [296] = PGM 16, 001 to 255 sec./min., 000 = Follows Deactivation Event, Default = 5 secondsInstead of deactivating the PGM on the occurrence of a specific event, the PGM will deactivate after the period programmed here has elapsed.If a PGM Delay is programmed, the deactivation event can be used as a second activation event.13.4 PGM OptionsSection [261] to [276]: PGM OptionsOption [1] OFF = PGM Base Time in Seconds (default)Option [1] ON = PGM Base Time in MinutesThis option sets the PGM delay in increments of minutes or seconds.Option [2] OFF = PGM State Normally Open (N.O.) (default)Option [2] ON = PGM State Normally Closed (N.C.)Option [3] OFF = PGM Supervision Disabled Option [3] ON = PGM Supervision Enabled (default)If enabled, the panel can wait for each of its assigned wireless transmitters to send a status signal within a specified time to confirm their presence and functionality.Option [4] OFF = PGM Activation Mode Steady (default)Option [4] ON = PGM Activation Mode PulseThis option sets the PGM to be either steady (ON), or pulsed (ON/OFF) when it is activated. Option [5] OFF = PGM Pulse once every 30 seconds disabled (default)Option [5] ON = PGM Pulse once every 30 seconds enabled](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-50.png)
![Magellan 47When armed, the PGM will pulse once every 30 seconds.Option [6] OFF = PGM Pulse on any alarm disabled (default)Option [6] ON = PGM Pulse on any alarm enabledThis option sets the PGMs to pulse on any alarm.Option [7] OFF = PGM Pulse on any alarm Partition 1(default)Option [7] ON = PGM Pulse on any alarm Partition 2Program PGMs to pulse during an alarm for either partition. With this feature enabled, and in combination with the Follow Arm/Stay Arm/Sleep Arm PGM type, the PGM will mimic the Arm LED. 13.5 PGM ProgrammingSections [301] to [316]The programming of the PGMs is accomplished in two steps:1. Assign the PGMs to the panel.2. Program the PGMs.PGM Programming can be executed through the Installer Quick Menu in the programming guide. 13.6 Viewing the PGM Signal StrengthSections [321] to [336]Once PGMs have been installed and assigned to the panel, the signal strength of each PGM can be verified in sections [321] to [336]. Sometimes moving the PGM or control panel by a small amount will greatly increase the signal reception.How Do I Assign PGMs to the Panel?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter the desired [SECTION NUMBER] (from sections [301] to [316]).4) Enter the 6-digit [SERIAL NUMBER] of the PGM.How Do I Delete Assigned PGMs?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)3) Enter the desired [SECTION NUMBER] (from sections [301] to [316]).4) Press the [0] key six times to clear the serial number.How Do I View a Wireless Transmitter’s Signal Strength?1) Press the [ENTER] key.2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default)3) Enter the desired [SECTION NUMBER] (from sections [321] to [336]).4) Press the transmitter’s anti-tamper switch or open the corresponding zone.5) The keypad will illuminate numbers 1 to 10.Signal Strength Indicator 8 to 10 / 3 beeps = Best signal 5 to 7 / 2 beeps = Average signal 1 to 4 / 1 beep = Weak signal (Relocate)](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-51.png)
![48 Reference & Installation Manual Part 14: System Settings14.1 Version Number DisplayEnter section [980] to view the version number of the panel. The first digit will appear. Press [ENTER] to scroll through each consecutive digit (the keypad will beep twice after every digit in the version number). Once the version number has been fully displayed, an acknowledgment beep (3 beeps) will sound and the first digit will be displayed again.14.2 Push Button Power ResetPerforming a hardware reset will set all control panel settings to factory default except for the Panel ID and PC Password. Also, the event buffer will not be erased. To perform a push button power reset:Press and hold the RESET switch for five seconds. The STATUS LED will start flashing fast. Within 2 seconds of this flashing, press the reset switch again. The panel will reset to default and restart14.3 Installer LockSection [395]000 = Disabled, 147 = Lock Enabled, Default = DisabledProgram 147 into section [395] to lock all programming. Performing a hardware reset will not affect the current panel settings. To remove the Installer Lock, enter 000. Please note that three seconds after turning on the control panel the STATUS LED and the relay on the control panel will flash fast for 6 seconds to indicate that the installer lock is enabled. Once enabled, the panel cannot be reset.14.4 Keypad Lockout FeatureSections [864]If a consecutive number of invalid codes are entered into a keypad, the control panel can be set to deny access from all keypads for a specified period and send the report code programmed in section [864]. Program the number of consecutive invalid codes from 001 to 255 (000 = disabled) into section [717]. Program the duration of the Keypad Lockout from 001 to 255 minutes into section [716]. 14.5 Battery Charge CurrentSection [700]: General Options Option [2] OFF = Battery Charge Current: 350mA (default)Option [2] ON = Battery Charge Current: 700mA (40VA transformer required)14.6 PartitioningSection [700]: General Options Option [1] OFF = Partitioning Disabled (default)Option [1] ON = Partitioning EnabledThe panel is equipped with a partitioning feature which can divide the alarm system into two distinct areas identified as Partition 1 and Partition 2. Partitioning can be used in installations where shared security systems are more practical, such as an office/warehouse building. When partitioned, each zone, each user code (see Access Codes on page 14) and some of the system's features can be assigned to Partition 1, Partition 2 or both. If the system is not partitioned, all user codes and features will be recognized as belonging to Partition 1.• Users can only arm partitions to which they have been assigned.• Only zones assigned to Partition 1 will arm/disarm when Partition 1 is armed or disarmed.• Only zones assigned to Partition 2 will arm/disarm when Partition 2 is armed or disarmed.• Zones assigned to both partitions will arm when both partitions are armed and will disarm when at least one disarms.• The following features can be programmed separately for each partition: Entry/Exit Delay Timer, Auto-arming Options, Bell Cut-Off Timer, Switch to Stay arming, PGM Events and Account Numbers. If the system is not partitioned, all zones, user codes, and features will be recognized as belonging to partition 1. Zones that have been manually assigned to partition 2 will no longer function.14.7 Confidential ModeSection [701] Options [3], [4] and [5] Option [3] OFF = Confidential Mode Disabled (default)Option [3] ON = Confidential Mode Enabled Option [4] OFF = Keypads activate when an access code is entered (default)Option [4] ON = Keypads activate when a key is pressed Option [5] OFF = Confidential Mode Timer is 2 minutes (default)Option [5] ON = Confidential Mode Timer is 5 seconds If Confidential Mode is enabled and no actions are performed on the keypads for the time defined by the Confidential Mode](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-52.png)
![Magellan 49Timer, all the keypad’s LEDs will be off until either a key is pressed or an access code is entered. When the system exits Confidential Mode, the keypads will display the system’s status. Confidential Mode is activated by enabling option [3]. Option [4] regulates whether the keypads will be activated at the touch of a key or only when an access code is entered. Option [5] determines the amount of time without action before the system enters Confidential Mode (5 seconds or 2 minutes).14.8 Installer Function KeysTo access the Installer Function keys, press:[ENTER]+[INSTALLER CODE]+[MEM] = Test R eport : Send the “Test Report” report code programmed in section [875] to the monitoring station. [ENTER]+[INSTALLER CODE]+[STAY] = Cancel Communication: Cancels all communication with WinLoad/BabyWare software or with the monitoring station until the next reportable event.[ENTER]+[INSTALLER CODE]+[SLEEP] = Answer WinLoad/BabyWare Software: Will force the console to answer an incoming call from the monitoring station that is using the WinLoad/BabyWare software. [ENTER]+[INSTALLER CODE]+[BYP] = Call WinLoad Software: Will dial the PC telephone number programmed in section [915] in order to initiate communication with a computer using the WinLoad software.[ENTER]+[INSTALLER CODE]+[TBL] = Installer Test Mode: The installer test mode will allow you to perform walk tests where the siren will squawk to indicate opened zones. Press the [TBL] key again to exit.14.9 Daylight Savings TimeSection [730]: General Zone Options 2Option [1] OFF = Daylight Savings Time Disabled (default)Option [1] ON = Daylight Savings Time Enabled With section [730] option [1] ON, the panel adjusts the system’s clock (time) for daylight savings changes. At 2:00AM on the second Sunday of a full weekend in March, the control panel will add one hour to the programmed time (clock). At 2:00 AM on the first Sunday of a full weekend in November, the control panel will subtract one hour from the programmed time (clock). By default, when section [730] is set at 18, the time is set for the US, Canada etc. For other countries see Daylight Savings Programming in the programming guide and set the country code in section [731].14.10 Customized Daylight Saving ProgrammingIn addition to using the default Daylight Saving Time (DST) settings in section [731], you can also set a customized DST. Set section [732] for the DST starting period and [733] for the DST ending period. Both sections recognize 5 different entries of 2 digits each. All entries must be assigned in this respective order: Country Code List (Default = bold)00 = US, Canada, Mexico, St.Johns, Bahamas, Turks and Caicos01 = Cuba02 = Brazil03 = Chile04 = Falklands05 = Paraguay06 = European Union, UK, and Greenland07 = Russia and most states of the former USSR08 = Australia- South Australia, Victoria, Australian Capital Territory, New South Wales09 = Lord Howe Island- Tasmania10 = New Zealand, Chatham11 = Tonga12 = Iraq and Syria13 = Israel14 = Lebanon, Kirgizstan15 = Palestine16 = Egypt17 = Namibia18 = USA, Canada (New Daylight Saving Time for 2007)19 = New Zealand (New Daylight Saving Time for 2007)Months 01 to 12 01 = January*If the day is set at 00, the DST will automatically change on the programmed country code listed above. Date 01 to 31 01 = First day of the monthDay 00 to 07 00 = Default*, 01 = SundayHours 00 to 23 00 = MidnightMinutes 00 to 59 00 = 60 minutes or 1 hourSection Data Description[732]__/__/__/__/__/__/__/__/__/__/ Daylight Savings Time Starting Period[733]__/__/__/__/__/__/__/__/__/__/ Daylight Savings Time Ending Period](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-53.png)
![50 Reference & Installation Manual 14.11 Audible Trouble Warning Except AC FailureSection [700]: General System Options Option [3] OFF = Audible trouble warning except AC failure (default)Option [3] ON = Audible trouble warning except AC failure When this option is enabled the panel will generate an audible trouble warning on all troubles except AC failure.14.12 Audible Trouble Warning on AC FailureSection [700]: General System Options Option [4] OFF = Audible trouble warning on AC failure (default)Option [4] ON = Audible trouble warning on AC failure When this option is enabled the panel will generate an audible trouble warning in the event of an AC failure.14.13 Display Entry Delay on LCD keypad (K32LCD, K32LCD+)Section [701]: General System Options Option [7] OFF = Display entry delay on LCD keypad Option [7] ON = Display entry delay on LCD keypad (default)When this option is enabled the panel will display entry delays on the K32LCD and K32LCD+ keypad modules.14.14 Display Exit Delay on LCD keypad (K32LCD, K32LCD+)Section [701]: General System Options Option [8] OFF = Display exit delay on LCD keypad Option [8] ON = Display exit delay on LCD keypad (default)When this option is enabled the panel will display exit delays on the K32LCD and K32LCD+ keypad modules.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-54.png)
![Magellan 51Part 15: Settings for WinLoad SoftwareWinLoad has not been verified by UL.15.1 Panel Answer OptionsThe following two options define how the control panel answers an incoming call from a computer using the WinLoad Software for Windows®. 15.1.1 Answering Machine Override DelaySection [902]000 = Disabled, 000 to 255 seconds, Default = 030When using the WinLoad software to communicate with an installation site that uses an answering machine or service, the answering machine override must be programmed. Using the WinLoad software you will call the control panel, hang up, then call back. If the installation site is called back within the programmed delay period, the control panel will override the answering machine or service by picking-up the line after the first ring on the second call. You must wait at least 10 seconds before attempting the second call, otherwise, the control panel will think it is the same call. For details on how to use the WinLoad software, refer to the WinLoad Help Manual. This section applies to the Plug-in Voice Dialer when using a VDMP3.Example: A security installation is using an answering machine set to answer after three rings. If section [902] has been programmed with 040 (40 seconds) and the second call is made within 40 seconds, the control panel will pick up the line on the first ring. If it takes more than 40 seconds, the control panel will not answer on the first ring and the answering machine will answer after three rings. 15.1.2 Number of RingsSection [901]000 = disabled, 001 to 015 rings, Default = 8 rings This value represents the number of rings the control panel will wait before picking-up the line. If the line is not answered after the number of programmed rings, the control panel will answer the call. This section applies to the Plug-in Voice Dialer when using a VDMP3.15.2 Panel IdentifierSection [910]0000 to FFFFThis 4-digit code identifies the control panel to the WinLoad software before initiating communication. The control panel will verify that the Panel Identifier in the WinLoad software is the same. If the codes do not match, the control panel will not establish communication. Therefore, be sure to program the same panel identifier into both the control panel and the WinLoad software. 15.3 PC PasswordSection [911]0000 to FFFFThis 4-digit password identifies the PC to the panel before establishing communication. Program the same PC Password into both the control panel and the WinLoad software. If the passwords do not match, the WinLoad software will not establish communication. 15.4 PC Telephone NumberSection [915]Up to 32 digitsThe control panel will dial this number when trying to initiate communication with a computer using the WinLoad software. You can enter any digit from 0 to 9 and any special keys or functions up to a maximum of 32 digits. 15.5 Call WinLoad Software[ENTER]+ [INSTALLER CODE] + [BYP] The control panel will dial the PC Telephone Number programmed in section [915] in order to communicate with the WinLoad software. The control panel and the WinLoad software will verify that the Panel Identifier and the PC Password match before establishing communication.](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-55.png)
![52 Reference & Installation Manual 15.6 Answer WinLoad Software[ENTER] + [INSTALLER CODE] + [SLEEP] In order to perform on-site upload/download connect your computer directly to the control panel using an ADP-1 line adapter. In the WinLoad software set Dialing Method to Blind Dial. Program the panel telephone number in WinLoad software and follow the instructions on the ADP-1 adapter. When the computer has dialed, press [ENTER] followed by the Installer/Maintenance Code, then press the [SLEEP] key to manually answer the WinLoad software from the control panel.15.7 Automatic Event Buffer TransmissionSection [900]: Dialer OptionsOption [2] OFF = Auto Event Buffer Transmission Disabled (default)Option [2] ON = Auto Event Buffer Transmission EnabledWhen the event buffer reaches 90% capacity, the control panel will make two attempts to establish communication with a PC using the WinLoad software by calling the PC Telephone Number programmed in section [915]. The WinLoad software must be in Wait to Dial mode. When the system establishes communication, it will upload the contents of the event buffer to the WinLoad software. If communication is interrupted before completing transmission or if after two attempts communication is not established, the system will wait until the Event Buffer attains another 90% capacity before attempting to re-communicate with the monitoring station. When the Event Buffer is full, each subsequent new event will erase the oldest event in the buffer.15.8 Call Back WinLoadSection [900]: Dialer Options Option [1] OFF = Call Back WinLoad Disabled (default)Option [1] ON = Call Back WinLoad EnabledFor additional security, when a PC using the WinLoad software attempts to communicate with the control panel, the control panel can hang up and call the PC back in order to re-verify identification codes and re-establish communication. When the control panel hangs up, the WinLoad software automatically goes into Wait for Call mode, ready to answer when the control panel calls back. Please note that the PC Telephone Number must be programmed in section [915] in order to use the Call Back feature.15.9 Connecting to WinLoadSerial ConnectorComputer containing WinLoad software307USB Adapter/CONV4USB Converter4-pin connector cableStandard DB-9 cable (9-pin serial cable)](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-56.png)
![Magellan 53Part 16: User Operation16.1 Alarm DisplayIf an alarm has occurred on a zone, the respective zone LED will flash, the [MEM] key will light up, and the zones will be stored in memory. These respective LEDs will continue to flash until disarming even if the zones are restored. To exit this mode and switch to live display mode before disarming, press the [CLEAR] key. Once the system is disarmed, the zones’ LEDs will turn off, while the [MEM] key remains lit. Press the [MEM] key to illuminate the LEDs corresponding to the zones that were in alarm. The alarm memory will be erased when the next alarm occurs and after a valid code is entered or upon full-arming the system.16.2 Trouble Display Press the [TBL] key to view the Trouble Display. Please note that the keypad can be programmed to emit a beep every 5 seconds whenever a new trouble condition has occurred. Press the [TBL] key to stop the beeping. To view the sub-menu, press the corresponding key in the main menu. Main Menu Trouble Sub-Menu Trouble Menu[1] Wireless zone low battery [1] to [32] Zones in low battery[2] Power trouble [1] Low/No battery on the control panel[2] AC failure on control panel[3] Auxiliary overload on control panel[4] Wireless keypad AC failure[5] Wireless keypad battery failure[6] Wireless repeater AC failure[7] Wireless repeater battery failure[3] Bell trouble [1] Bell disconnect on control panel[2] Bell overload on control panel[4] Communication trouble [1] Telephone Line Monitoring on control panel[2] Fail to communicate on Monitoring Telephone 1 on control panel[3] Fail to communicate on Monitoring Telephone 2 on control panel[4] Fail to communicate on pager telephone on control panel[5] Fail to communicate on voice telephone on control panel[6] Fail to communicate with PC on control panel[5] Tamper and zone wiring failure [1] to [32] Zones in tamper and zone wiring failure[6] Module tamper trouble [1] 2WPGM[2] Keypad bus[3] ZX8 Bus Module [4] RTX3 Bus Module [5] Wireless keypad[7] Fire loop trouble [1] to [32] Zones in fire loop trouble[8] Timer loss[9] Wireless zone supervision loss [1] to [32] Zones in supervision lost6[STAY] RF interference trouble[0 (10)] or [10] Module supervision loss [1] 2WPGM[2] Keypad bus (Panel reset will not clear this trouble, clear it in section [955])[3] ZX8 Bus Module [4] RTX3 Bus Module [5] Wireless keypad supervision failure[6] Wireless repeater supervision failure[16] Keypad fault (K32/K32+,K32RF only)[SLEEP] Keypad fault (K10V/H only)](https://usermanual.wiki/Paradox-Security-Systems/MG5050V2/User-Guide-4208162-Page-57.png)
