Pasco Specialty And Mfg Rlc Circuit Ci 6512 Users Manual 012 04818d

: Pasco-Specialty-And-Mfg Pasco-Specialty-And-Mfg-Rlc-Circuit-Ci-6512-Users-Manual-516807 pasco-specialty-and-mfg-rlc-circuit-ci-6512-users-manual-516807 pasco-specialty-and-mfg pdf

Open the PDF directly: View PDF .
Page Count: 2

Instruction Sheet

for the PASCO

Model CI-6512

RLC Circuit

012-04818D

03/99

$1.00

© 1992 PASCO scientific

This instruction sheet written/edited by: Dave Griffith

330

µF

100

µF

10Ω

33Ω

100Ω

150Ω

Model CI-6512

RLC

C IRCUIT

MAXIMUM WORKING

VOLTAGE: 10V

7.5V

0.22A

#50

BULB

8.2 mH

KIT NO.

Inductor

Steel Rod

Resistors

Capacitors

Bi-Color

LED

Lamp

Introduction

The R LC Circuit board is designed to be used with a

PASCO ScienceWorkshop 700 Series Computer

Interface or 6500 Series Computer Interface to study

the behavior of resistors, inductors and capacitors in an

AC circuit. The board includes several resistors, two

capacitors, a #50 miniature screw lamp, a bi-color light

emitting diode and an air-core inductor. A 5/8" X 21/2"

steel rod (included) can be used to increase the induc-

tance of the coil.

➤ Note: Prior to the first use, remove the bolt that

secures the coil ( Inductor ) during shipping.

Additional Equipment Required:

•ScienceWorkshop 700 Series Computer Interface

or 6500 Series Computer Interface

• Power Amplifier, (CI-6502, CI-6552)

• Banana Plug Patch Cords, PASCO Model SE-9750

or SE-9751.

➤ Note: The RLC circuit can be used with the

built-in power amplifier of the Science Workshop

750 Interface and does not require the external

Power Amplifier ( CI-6552A ) for most

experiments.

2

012-04818D

Setup Procedure:

➀Connect the Power Amplifier to Analog Channel A

or B of the PASCO Computer Interface.

➁Connect the output of the Power Amplifier to the

RLC Circuit with banana plug patch cords.

➂Refer to the Power Amplifier experiments guide,

the Computer Interface experiments guide, or the

Experiment Guide diskette for specific suggestions

on using the RLC Circuit.

Specifications

Resistors: 100 Ω, 1 W; 33Ω, 5W; 10Ω, 10W

Capacitors: 100µF, 16V and 330µF, 16V

(➤ NOTE: Capacitance values may vary by ±20%)

Lamp: 7.5V, 0.22A, #50 miniature screw style

LED: red (655 nm)/green (565 nm); typical forward

voltage = 1.7-2.1 volts; average brightness

@ 20 mA = 1.5 mcd

Inductor: 8.2 mH @1 kHz, 6.5Ω maximum DC

resistance, 0.8A current rating RMS,

3/4" I.D. X 13/4"O.D.

Replacement Parts:

#50 Lamp Part No. 526-031

Steel core Part No. 648-04783

LED Part No. 527-019

Equipment Return

Should this product have to be returned to PASCO

scientific for any reason, notify PASCO scientific by

letter or telephone BEFORE returning the product. Upon

notification, the return authorization and shipping instruc-

tions will be promptly issued.

➤ NOTE: NO EQUIPMENT WILL BE

ACCEPTED FOR RETURN WITHOUT AN

AUTHORIZATION FROM PASCO.

When returning equipment for repair, the units must be

packed properly. Carriers will not accept responsibility

for damage caused by improper packing. To be certain

the unit will not be damaged in shipment, observe the

following rules:

➀The carton must be strong enough for the item

shipped.

➁Make certain there are at least two inches of packing

material between any point on the apparatus and the

inside walls of the carton.

➂Make certain that the packing material cannot shift in

the box, or become compressed, thus letting the instru-

ment come in contact with the edge of the box.

Limited Warranty

PASCO scientific warrants this product to be free from

defects in materials and workmanship for a period of one

year from the date of shipment to the customer. PASCO

will repair or replace, at its option, any part of the product

which is deemed to be defective in material or workman-

ship. This warranty does not cover damage to the product

caused by abuse or improper use. Determination of

whether a product failure is the result of a manufacturing

defect or improper use by the customer shall be made

solely by PASCO scientific. Responsibility for the return

of equipment for warranty repair belongs to the customer.

Equipment must be properly packed to prevent damage

and shipped postage or freight prepaid. (Damage caused

by improper packing of the equipment for return ship-

ment will not be covered by the warranty.) Shipping

costs for returning the equipment, after repair, will be

paid by PASCO scientific.