Paul C Buff CSXCVR1 CYBERSYNC TRANSCEIVER 1 User Manual USERS MANUAL

Download:
Mirror Download [FCC.gov]
Document ID	927983
Application ID	eOQOvyHsjzG+q6XDdOhJvQ==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.84kB (73024 bits)
Date Submitted	2008-04-15 00:00:00
Date Available	2008-04-16 00:00:00
Creation Date	2008-04-11 15:51:43
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2008-04-11 15:51:44
Document Title	USERS MANUAL
Document Creator	PScript5.dll Version 5.2

Certification Exhibit
FCC ID: OUECSXCVR1
IC: 6866A-CSXCVR1
FCC Rule Part: 15.249
IC Radio Standards Specification: RSS-210
ACS Report Number: 08-0097-15C
Manufacturer: Paul C. Buff, Inc.
Model: CyberSync Transceiver 1
Manual
5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598
Paul C. Buff, Inc.
CyberSyncTM Transceiver Module 1
Application Information
CyberSyncTM Transceiver Module 1 is a self-contained, fully operational 2.4 Ghz modular multichannel radio transceiver designed to be used exclusively with host products containing a connector
specifically designated as an interface for the Paul C. Buff, Inc. CyberSyncTM Transceiver Module 1.
The Transceiver 1 module is powered by its host device, and contains all necessary decoupling and
shielding required to meet FCC Part 15 Modular Transmitter Approval criteria. The module is
connected to its host device by an eight-pin header system. The host equipment provides a 3 Vdc
regulated and filtered power source, channel selection data, T/R switching, and data output to the
device when used as a transmitter, as well as data decoding when the module is used in its Receiver
mode of operation.
The module is either contained directly within the host product, as installed at the factory following
strict guidelines provided by Paul C. Buff, Inc., or is supplied in a separate enclosure for plug-in
connection to a host product incorporating a mating cavity with female connector configured according
to strict guidelines provided by Paul C. Buff, Inc., and labeled “For connection to Paul C. Buff, Inc.
CyberSyncTM Transceiver Module only.”
The host product is required to a visible bear a label or imprint stating:
Contains FCC ID: OUECSXCVR1
Contains IC: 6866A-CSXCVR1
APPLICATION WARNINGS
The Transceiver 1 module incorporates a self-contained transmission line type antenna that is part of
the module circuit board. When connecting the module to its host equipment, do not scratch, bend, or
otherwise alter the antenna portion of the circuit board, which appears as a long, narrow section of the
substrate material extending from the rectangular section of the board. Do not remove the film solder
mask from the antenna section, and do not attach any other wire, external antenna, or antenna
connector to the antenna section. Incorrect installation of the module is likely to result in unauthorized
modes of operation, and/or damage to the module's components.
When completing the installation of this module, make certain that the appropriate FCC Approval label
is affixed to the host device exterior surface as instructed by the host device assembly instructions.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
●
●
●
●
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
STATEMENT: The term 'IC:' before the radio certification number only signifies that Industry
Canada technical specifications were met.
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment
Regulations. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l'interférence canadienne
causant des règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce
dispositif peut ne pas causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle
interférence reçue, y compris l'interférence qui peut causer l'opération peu désirée.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 3
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:29aa4cd0-38eb-449d-adbf-fcd72271d63a
Modify Date                     : 2008:04:11 15:51:44-04:00
Create Date                     : 2008:04:11 15:51:43-04:00
Metadata Date                   : 2008:04:11 15:51:44-04:00
Document ID                     : uuid:73c6085f-cac9-44e5-bb5d-f6958985b9d6
Format                          : application/pdf
Creator                         : PScript5.dll Version 5.2
Producer                        : Acrobat Distiller 6.0 (Windows)

EXIF Metadata provided by EXIF.tools