Paxton Access 360864 125 kHz Proximity Reader User Manual INSTRUCTION PROXIMITY architectural reader

Paxton Access Ltd 125 kHz Proximity Reader INSTRUCTION PROXIMITY architectural reader

User manual

Download: Paxton Access 360864 125 kHz Proximity Reader User Manual INSTRUCTION   PROXIMITY architectural reader
Mirror Download [FCC.gov]Paxton Access 360864 125 kHz Proximity Reader User Manual INSTRUCTION   PROXIMITY architectural reader
Document ID828814
Application ID1j1TzCJKVLH87IXBRZhfeA==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize101.17kB (1264592 bits)
Date Submitted2007-08-14 00:00:00
Date Available2007-08-14 00:00:00
Creation Date2007-07-06 15:16:41
Producing SoftwareAdobe PDF Library 7.0
Document Lastmod2007-07-11 12:24:01
Document TitleINSTRUCTION - PROXIMITY architectural reader
Document CreatorAdobe InDesign CS2 (4.0.5)

06/07/2007
Ins-30040-US
PROXIMITY architectural reader
Technical Support
1 800 672 PAXT
support@paxton-access.co.uk
Technical help is available:
Monday - Friday from 5am - 5pm PST / 8am - 8pm EST
Other documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/
Fitting
Mount the reader back box flush into the wall. Care must be taken when doing this, as there is no further
adjustment possible within the box. Screws and plugs are provided for fitting the unit to the wall.
Line up the two locating pins on the top of the reader with the top plate inside the back box. Once located, the
reader can be clipped into the box at the bottom using the clip feature.
Check that the reader is located against the surface of the wall. If there is a gap between the reader and the wall,
or if the reader will not successfully clip into the box, remove the reader and adjust the mounting plates inside the
back box using a 3mm Allen key.
To remove the reader, insert the tool provided into the cut out on the underside of the reader. Push up the clip
and pull the reader from the back box.
Wiring
Red
Power
Relay 1
Relay 2
N.C.
CAUTION: for 12v d.c. readers only. For
correct connection of old 5v readers, refer to
instructions.
N.O.
Com
N.O.
24898 00000
Com
Alarm Output
0v
Contact
Inputs
0v
Exit
0v
PSU
12v
5v
OK
PSU
Exit
Tx
Rx
Tamper
Orange
Contact
0v
Tamper
Relay 2
White/Orange
Relay 1
Green
+12v
N.C.
Network
CAT5 cable coding
White/Green
Brown
Serial number
241821
Test ID: 012345678901
Screen or spare cores
from network cable
Orange
Green
Yellow
Blue
Keypad 1
Orange
Mauve
Black/White
Reader 2
z-1440
Mauve
Brown
Black/White
Blue
Yellow
Brown
Green
Yellow
Reader 1
Orange
Yellow
Orange
Keypad 2
Red 12v dc
Brown
Green
Yellow
Blue
Control
unit
Alarm
Door relay
Orange
Card reader or keypad
Brown
Power
Switch
Red 12V
Bell
12v
0v
N.C.
N.O.
Com
Mauve
Black
Exit
Inputs
Contact
CAUTION: For 12V d.c. readers only.
For correct connection of old readers,
refer to instructions.
Cable extensions
Readers can be extended using Belden CR9540 10-core overall screened cable. The maximum cable length
between reader and control unit is 100 yards.
Power
Red
Relay 1
Relay 2
Brown
0v
Contact
0v
Inputs
Exit
0v
PSU
Orange
Green
Yellow
Blue
Control
unit
Mauve
Black
Exit
Inputs
Contact
Alarm
Card reader or keypad
Brown
Power
Switch
Red
Door relay
5v
12v
OK
PSU
Exit
Tx
Rx
White Labelled control units only provide 5v at
the Red terminal. The red power wire for the
reader should be connected directly to the 12v
PCB supply terminal - as per diagram.
Orange
Orange
Tamper
N.O.
Com
Tamper
Contact
White/Orange
Relay 2
Relay 1
Green
N.O.
Com
Alarm Output
Network
White/Green
CAT5 cable coding
0v
N.C.
Screen or spare cores
from network cable
+12v
N.C.
24898 00000
Keypad 1
Brown
Yellow
Black/White
Serial number
241821
Mauve
Test ID: 012345678901
Blue
Orange
Green
Reader 2
z-1440
Green
Yellow
Reader 1
Orange
Yellow
Blue
Mauve
Black/White
Brown
Yellow
Orange
Keypad 2
Red
Brown
Bell
12v
0v
N.C.
N.O.
Com
Frequently asked questions
Here is the list of topics about this product that receive the most technical support enquiries. We
list them here to help you speed up the installation and trouble shooting process.
1 - Readers/Keypads not working
. Software settings - Confirm that the settings of the reader or keypad are correct.
. Connections - Check the wiring and integrity of reader/keypad terminal connections.
. To confirm that an extended reader cable is not at fault, wire the reader direct into the reader port. If the reader
works, this indicates a problem with the cable.
. Supply voltage - confirm that the reader has sufficient voltage.
. User token - Check that the user token used for testing the reader is operational.
. Interference - Confirm whether the reader works when tested ‘in hand’ and not mounted on the wall. Ensure that
readers are not mounted back to back or there is not interference from other RF devices.
2 - Readers / Keypads - Extending cable
. Only Belden CR9538 /9540 can be used for cable extensions. CR9538 is 8 core for up to 25m, CR9540 10 core
for 25-100m (maximum extension). When using CR9540, the two additional cores should be used to double up for
power.
3 - Net2 - What to do if a user has no access
. Check the reader LEDs when a card is shown:
No LEDs - the reader has no power.
No change in display - try the card on a known working readers. If there is still no response, replace the card.
Green LED flashing when a card is presented, check the Relay 1 LED to check activity and the wiring to the lock.
Red LED is flashing when a card is presented, check the validity of the user at the PC.
- Check user’s access level and ensure they have access by clicking on Current Validity.
- Check the ‘Valid Until’ date and confirm this has not expired.
Reinstate the ACU from the doors screen. Select the ACU’s you wish to reinstate and then click OK.
4 - Switch2 - Adding an additional card pack
. You need to be in possession of the original enrolment card. Present the original enrolment card to the reader
and the Amber LED will flash, Green & Red LEDs will be off, then present the Enrolment card from the new card
pack; the reader will beep and all LEDS will be lit. The additional cards will now be valid. Repeat this with each
reader and with any additional card packs. Any valid enrolment card can be used to add further packs. This is the
same for enrolling function card packs onto a system.
5 - Switch2 - How to reset the controller
. Disconnect the power and remove the wires from the Green and Mauve terminals
. Insert a wire link between the Green and Mauve terminals
. Reconnect the power (the unit will bleep 4 times)
. Disconnect the power and remove the link wire, reconnect the Green and Mauve wires
. Reconnect the power (the unit will bleep 3 times per second). The unit is ready to be enrolled.
Suitability
Security sensitive doors
Mounted on metal surface
Wet environments
Readers mounted together
300mm
between
readers
Specifications
Environment
Operating temperatures - all items
Min
Max
-20 °C (-4 °F)
+55 °C (+131 °F)
IPX7
Waterproof
5 yards
Cable length
Electrical
Voltage
Min
Max
8v DC
14v DC
60 mA
Current
Carrier frequency
125 kHz
600 µs
Clock and data bit period
Dimensions
Width
Backbox
2 3/8”
4”
1”
Token
Keyfob
Hands Free Token
1”
15”
1/2”
3/8”
Depth
Reader
Read Range
3/4”
Height
3/8”
The declaration of conformity may be
consulted at - http://paxton.info/596
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 4
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:5140ff8b-1ca6-4b7a-8693-234bb1f565c4
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Create Date                     : 2007:07:06 15:16:41+01:00
Metadata Date                   : 2007:07:11 12:24:01+01:00
Modify Date                     : 2007:07:11 12:24:01+01:00
Creator Tool                    : Adobe InDesign CS2 (4.0.5)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 7115 bytes, use -b option to extract)
Instance ID                     : uuid:e63bdfeb-a60b-43c8-b46e-feeed933645e
Rendition Class                 : proof:pdf
Document ID                     : adobe:docid:indd:9cf953d9-2bc7-11dc-bb08-e0b114d1b573
Derived From Instance ID        : 9cf953d8-2bc7-11dc-bb08-e0b114d1b573
Derived From Document ID        : adobe:docid:indd:9cf953d4-2bc7-11dc-bb08-e0b114d1b573
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 300.00, 72.00, 72.00, 72.00, 600.00, 72.00, 72.00, 600.00
Manifest Placed Y Resolution    : 300.00, 72.00, 72.00, 72.00, 600.00, 72.00, 72.00, 600.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Document ID  : uuid:8e68e80f-29c7-4ef0-97f2-2d95e832cc3e, uuid:178544C3952BDC118FBCEA0D107ACD62, uuid:4BD2AC71E42ADC119904A2AF3B78F777, uuid:4DD2AC71E42ADC119904A2AF3B78F777, adobe:docid:photoshop:f86ae1bc-64fb-11db-8a3e-971789a20d84, uuid:74E12175D014DC11871E8A11CCC80BFB, uuid:45D2AC71E42ADC119904A2AF3B78F777, adobe:docid:photoshop:f86ae1bc-64fb-11db-8a3e-971789a20d84
Manifest Reference Instance ID  : uuid:5157f64e-acfe-4a8f-9152-dc787454e60b, uuid:3c65c168-c159-4af4-8fda-ead22616b3ea, uuid:ff68cd9d-300c-472b-a3c4-5017607624a7, uuid:89337853-2ab2-49ca-b1d1-572358fef1cd, uuid:e781cc09-ed38-4ef4-8d40-7bde3cff3280
Format                          : application/pdf
Title                           : INSTRUCTION - PROXIMITY architectural reader
Creator                         : Adobe InDesign CS2 (4.0.5)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: USE360864

Navigation menu