Paxton Access 654943 Net2 nano 1 door access control unit User Manual

Paxton Access Ltd Net2 nano 1 door access control unit INSTRUCTION Net2 nano control unit

a href="https://usermanual.wiki/Paxton-Access" itemprop="url"> Paxton Access >

User Manual

redaeR:noituaCylnosredaerCDV21roF12VRed LED Amber LED Green LED Data/D0Clock/D1Media Detect 0VEntry12V12V Lock 0V0VN.C.N.O.COMAlarm12VGreen LED Exit0VContact 0V0VTamperPSU0VnottuBtixEyaleRkcoLstuptuOstupnIrewoPtcatnoCrepmaT/USPNet2 nano http://paxton.info/107123456088912345126Ins-30075-US Net2 nano control unitExit button(push to make)Reader/keypadTamper switch(optional)Door contact switch(held closed by door)Paxton Access05/03/2009Technical SupportTechnical help is available: Monday - Friday from 12:00 AM - 5:00 PM (PST) Saturday from 1:00 AM - 5:00 AM (PST)1.800.672.PAXT support@paxton.co.ukTo 12V DC power supplyThis is the heartbeat of the system and should pulse regularly. This indicates that the processor is functioning.Net2Air wireless activity (Tx/Rx) - Blue12V (Green) - Power LED.Lock (Orange) - The 12V lock output is energised.Relay (Orange) - The relay is energised - (NO/COM contacts are closed).Alarm (Red) - 12V Alarm output is active.Exit (Orange) - The exit button contacts are closed.Contact (Orange) - The door contacts are closed.Tamper (Orange) - The tamper contacts are closed.PSU (Orange) - The PSU contacts are closed.Net2Air (Blue) - Net2Air interface Tx/Rx activity.OK (Green ash) - The internal software is running.LED indicationsDocumentation on all Paxton Access products can be found on our web site - http://www.paxton-access.com/Net2 nano is a wireless based 1 door access control unit. It is recommended that a Net2Air site surveyor is used to determine the best position for the bridge and units.Diagnostic LEDsThis unit requires a Net2Air bridge (USB or Ethernet) to communicate with the controlling PC running Net2 v4.14 or later software.*not connected*Lock releaseNOTE: A new unit requires approximately 30 seconds after initial power up to self congure. During this time the OK LED will not be ashing.The unit will not operate until this operation has completed.
Control unit installationWire the components to the Access Control Unit (ACU) as shown on the rst page. This will include: - Reader/Keypad - Electric Lock - Power supply - Any other optional componentsPress the exit button or in the absence of an exit button short the 0V and exit terminals to test the relay function. The Relay LED will come on and the lock should release.The access control unit connects to the Net2 software running on the PC using Paxton Access’ Net2Air proprietary wireless technology. The Net2Air USB bridge enables communication from the Net2 software to the Paxton Access nano family of products.Radio signals do not always behave as you might expect. For example, a mobile phone that displays a full signal on one part of the site will lose signal completely only a few metres away. These problems can be addressed by using the Net2 site surveyor kit. (690-200-US)See also: XAN1095 - Net2 nano - How does it work? < http://paxton.info/974 >X AN1096 - How to plan a Net2 nano installation < http://paxton.info/975 >X Ins-30096-US - Net2Air site surveyor < http://paxton.info/1193 >Data transfer with wireless technology requires far more control and error checking than with a hard wired data line connection. Net2 classic runs with a server that originates and controls all the communications on the data line. This would not be efcient in a wireless environment.We therefore give the Nano controller the active role. Each Nano is always active and transmits data bursts (including a regular Heartbeat) every few seconds. The Net2 server then acts upon these requests for service.The PC requires at least one Net2Air bridge to communicate with a Nano. This can be a local Net2Air USB bridge (only one per system) and/or multiple Net2Air Ethernet bridge units connected to the PC via a TCP/IP connection.Net2 nano PC / server operationNet2Air wireless communicationPC InstallationThe current specication for compatible PC hardware, network and operating systems is available on our website at the following link: http://paxton.info/720There is NO Net2 nano detection function. It is recognised that there could be security issues if the wireless units were detectable from outside the site. During installation, a nano unit makes a permanent one-to-one link with a Net2Air bridge and is then enrolled into the Net2 database.The wireless Net2 nano is fully compatible with the hard wired Net2 range but there are several important differences that need to be understood before installing the equipment. The most important of these being the location of the units and their bridge components.These principles are therefore explained rst before we move on to the Net2 nano unit itself.The readers default indication has all the LEDs on. Access granted is denoted with a single ashing Green LED, Access Denied is a single ashing Red LED. NOTE: A Net2 nano ACU or a Hands free interface cannot be installed in a Metal cabinet as this would block the RF signal used for the Net2Air wireless technology.ReaderControl unitNet2 ServerAn entry is then made on the Doors screen and a special icon is used to denote the wireless connection.
Download:
Mirror Download [FCC.gov]
Document ID1079166
Application IDfQ6DVeuq/Zy7J+2b+hLmrg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize184.92kB (2311457 bits)
Date Submitted2009-03-11 00:00:00
Date Available2009-03-11 00:00:00
Creation Date2009-03-05 10:23:58
Producing SoftwareAdobe PDF Library 7.0
Document Lastmod2009-03-05 10:26:54
Document TitleINSTRUCTION - Net2 nano control unit
Document CreatorAdobe InDesign CS2 (4.0)
FCC ID Filing: USE654943

Navigation menu