Paxton Access 690333 690-333-US Net2 Hands Free Keycard User Manual

Paxton Access Ltd 690-333-US Net2 Hands Free Keycard

User manual

Ins-30037-US Net2Air Hands Free Active Keycard10/04/2007Technical SupportTechnical help is available: Monday - Friday from 5am - 5pm PST / 8am - 8pm EST Other documentation on Net2 can be found on our web site - http://www.paxton-access.com/1 800 672 PAXT support@paxton-access.co.ukBattery replacementThe keycard has been designed with features to extend battery life, these include a two second timeout once access has been granted and a capability to prevent repeated access to the same door whilst the keyfob remains in the eld of the reader. Leaving the keycard in the eld of a reader will reduce battery life.Remove the screw on the back of the card. Open the case by inserting a at head screw driver in the slot at the bottom of the card and gently prising the case open. Remove the circuit board and replace the batteries. Replace the circuit board, casing cover, screw and label. The Net2Air Interface has a pair of switches labelled SW2. When switch one is set to ‘on’ the interface will respond when button 1 is pressed. When switch two is set to ‘on’ the interface will respond when button 2 is pressed.Interface Settings To congure keycard buttons the keycard must rst be read by the reader without pressing buttons. The keycard automatically stores the details of the interface and will activate the door using the button specied by the SW2 setting.The keycard can store up to 14 doors, seven for each button. Data Reset To clear the stored gate information from the keycard hold down both buttons for 3 seconds. To initialise the button functions of a Keycard the interface needs to be congured. The Net2Air system comprises of a Net2Air Hands Free Interface, a compatible reader (see specication table) and Net2Air keycards or keyfobs. The hands free system operates by using the eld being transmitted by the reader to wake up the token. This then communicates with the interface which contains a long range receiver.The Net2 keycard increases this effective read range to a maximum of 50 yards. This is acheived by activating the system manually instead of using the reader eld (maximum 2.7 yards.)Net2Air keycards also include a standard proximity ID chip and can therefore be presented to any Paxton proximity reader whether they are using the Net2Air interface or not.Switch 1 ‘on’ Barrier inSwitch 2 ‘on’ Barrier out Button 1 Barrier inButton 2 Barrier outSW2What is Net2Air?
Dimensions Length 3 3/8 ”Width 2 1/8 ”Depth 3/8 ”System SpecicationsWake up frequency 125 kHzCommunications frequency 2.4 GHzOperating temperature 0 °C - 50 °C (Battery Specication)Typical battery life 5 yearsBattery type 1 x CR2430Read range with Net2Air KeycardWith button - all readers up to 50 yardsP38 3 feetP50 4 feetP75 5 feetP200 8 feetP200 metal mount 6 feetSpecicationsFCC ComplianceThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment.
Ins-30037-US Net2Air Hands Free Active Keycard20/03/2007Technical SupportTechnical help is available: Monday - Friday from 5am - 5pm PST / 8am - 8pm EST Other documentation on Net2 can be found on our web site - http://www.paxton-access.com/1 800 672 PAXT support@paxton-access.co.ukBattery replacementThe keycard has been designed with features to extend battery life, these include a two second timeout once access has been granted and a capability to prevent repeated access to the same door whilst the keyfob remains in the eld of the reader. Leaving the keycard in the eld of a reader will reduce battery life.Remove the screw on the back of the card. Open the case by inserting a at head screw driver in the slot at the bottom of the card and gently prising the case open. Remove the circuit board and replace the batteries. Replace the circuit board, casing cover, screw and label. The Net2Air Interface has a pair of switches labelled SW2. When switch one is set to ‘on’ the interface will respond when button 1 is pressed. When switch two is set to ‘on’ the interface will respond when button 2 is pressed.Interface Settings To congure keycard buttons the keycard must rst be read by the reader without pressing buttons. The keycard automatically stores the details of the interface and will activate the door using the button specied by the SW2 setting.The keycard can store up to 14 doors, seven for each button. Data Reset To clear the stored gate information from the keycard hold down both buttons for 3 seconds. To initialise the button functions of a Keycard the interface needs to be congured. The Net2Air system comprises of a Net2Air Hands Free Interface, a compatible reader (see specication table) and Net2Air keycards or keyfobs. The hands free system operates by using the eld being transmitted by the reader to wake up the token. This then communicates with the interface which contains a long range receiver.The Net2 keycard increases this effective read range to a maximum of 50 yards. This is acheived by activating the system manually instead of using the reader eld (maximum 2.7 yards.)Net2Air keycards also include a standard proximity ID chip and can therefore be presented to any Paxton proximity reader whether they are using the Net2Air interface or not.Switch 1 ‘on’ Barrier inSwitch 2 ‘on’ Barrier out Button 1 Barrier inButton 2 Barrier outSW2What is Net2Air?
Dimensions Length 3 3/8 ”Width 2 1/8 ”Depth 3/8 ”System SpecicationsWake up frequency 125 kHzCommunications frequency 2.4 GHzOperating temperature 0 °C - 50 °C (Battery Specication)Typical battery life 5 yearsBattery type 1 x CR2430Read range with Net2Air KeycardWith button - all readers up to 50 yardsP38 3 feetP50 4 feetP75 5 feetP200 8 feetP200 metal mount 6 feetSpecicationsFCC ComplianceThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment.

Navigation menu