Paxton Access 6903M2 Net2 Hands Free Keycard - mk2 User Manual INSTRUCTION Hands free Keycard for Net2
Paxton Access Ltd Net2 Hands Free Keycard - mk2 INSTRUCTION Hands free Keycard for Net2
User Manual
24/04/2009 Ins-30106-US Hands free Keycard for Net2 Technical Support 1.800.672.PAXT Technical help is available: support@paxton.co.uk Monday - Friday from 12:00 AM - 5:00 PM (PST) Saturday from 1:00 AM - 5:00 AM (PST) Documentation on all Paxton Access products can be found on our web site - http://www.paxton-access.com/ What is Hands Free? The system comprises of a Hands Free Interface, a compatible reader (see specification table) and hands free keycards or keyfobs. The system operates by using the field being transmitted by the P series reader to wake up the token. This then communicates with the interface which contains a long range receiver. The keycard increases this effective read range to typically 5 yds (maximum 50 yds). This is achieved by activating the system manually instead of using the reader field (maximum 8 feet) Keycards also include a standard EM4100 proximity ID chip and can therefore be presented to any compatible proximity reader whether they are using the Hands Free interface or not. The keycard has been designed with features to extend battery life, these include a two second timeout once access has been granted and a capability to prevent repeated access to the same door whilst the keyfob remains in the field of the reader. Leaving the keycard in the field of a reader will reduce battery life. SW2 Hands free interface Switch settings The card will beep as confirmation when it has communictated with the hands free interface. This does NOT mean that access has been granted as that is determined by the access permissions assigned to the user. Interface Settings To enable the buttons, the keycard must first be presented to the P series reader and then used in hands free mode. The keycard stores the details of this interface and can then activate the door using a button. It can still be used in normal hands free mode and also in local passive mode with other standard readers. The hands free interface has a pair of switches labelled SW2. Select either switch 1 or 2 to set which button the interface will respond to and then power cycle the interface to store this setting. Data Reset The keycard can store up to 14 doors, seven for each button. To clear the stored gate information from the keycard hold down both buttons until the beep sounds continually. Battery replacement The battery is retained by a spring clip cover. Locate the small slot aperture below its bottom edge. Restrain the cover with gentle pressure while lifting the lower edge with a small screwdriver. The spring clips on the cover will release to reveal the battery. Once the battery has been replaced, place the cover directly above the opening and push down to latch it home. Specifications Min Max 0 °C (32 °F) 50 °C (122 °F) Dimensions Width 3 3/8 in Height 2 1/8 in Depth 3/8 in System Specification Token type Carrier frequency EM4100 - 125 kHz 2.4 GHz Environment Operating temperature Electrical Typical Battery Life Battery Type 5 years 1 x CR2430 Read range with Hands Free token With button - all readers > 5 yds P38 3 ft P50 4 ft P75 5 ft P200 8 ft P200E metal mount 6 ft Long range reader 16 ft SAFETY WARNING RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. We hereby declare that the Net2 Hands Free Keycard mk2 FCC ID: USE6903M2 is a portable device which has a maximum transmit power of 0.24 mW and is not subject to the routine RF exposure evaluation as per Section 2.1093 of the FCC rules.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 2 XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:aa02dccf-54b9-45a8-88b6-cd1ea647532e Producer : Adobe PDF Library 7.0 Trapped : False Create Date : 2009:04:28 08:42:40+01:00 Metadata Date : 2009:04:28 08:45:38+01:00 Modify Date : 2009:04:28 08:45:38+01:00 Creator Tool : Adobe InDesign CS2 (4.0.5) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 9321 bytes, use -b option to extract) Instance ID : uuid:c25b97e2-10ef-4ca7-a646-f388185a1cb7 Rendition Class : proof:pdf Document ID : adobe:docid:indd:98c4b87a-30e1-11de-aaef-d93684513128 Derived From Instance ID : 98c4b879-30e1-11de-aaef-d93684513128 Derived From Document ID : adobe:docid:indd:1adc3a55-30d4-11de-8945-f524739a9c04 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 300.00, 72.00, 180.00, 180.00 Manifest Placed Y Resolution : 300.00, 72.00, 180.00, 180.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches Manifest Reference Document ID : uuid:8e68e80f-29c7-4ef0-97f2-2d95e832cc3e, uuid:B1954BDAAD9EDD119187961EE711D7AC, adobe:docid:photoshop:e28313f7-a5b3-11dd-9557-c94ee0ceb37f, adobe:docid:photoshop:203bed2c-a5b4-11dd-9557-c94ee0ceb37f Manifest Reference Instance ID : uuid:50954530-7446-4e1c-90e0-cffdd79d371e Format : application/pdf Title : INSTRUCTION - Hands free Keycard for Net2 Tagged PDF : Yes Creator : Adobe InDesign CS2 (4.0.5)EXIF Metadata provided by EXIF.tools