Brochure

1000300948-Brochure 1000300948-Brochure 1000300948-Brochure B5 unilog cesco-content

1000450869-Brochure 1000450869-Brochure 1000450869-Brochure B5 unilog cesco-content

1000507152-Catalog 1000507152-Catalog 1000507152-Catalog B5 unilog cesco-content

1000217405-Attachment 1000217405-Attachment 1000217405-Attachment B5 unilog cesco-content

2016-10-06

: Pdf 1000217407-Brochure 1000217407-Brochure B5 unilog

Open the PDF directly: View PDF .
Page Count: 32

Flush activations

offer a full range

of power and

communication

connections.

Pro Series presets

offer large access

area into the duct.

ED830R13 – Updated Septemeber 2015 – For latest specs visit www.legrand.us/wiremold

Presets have

room to store up

to 1 meter of cable

in preset. Fiber

loop clips (Cat. No.

427) shown.

IMPORTANT!

A minimum 1 1/2" [38mm] preset or afterset is required on Pro Series duct to support standard duplex receptacles and

communication devices when using flush activations. The 1" [25mm] preset or afterset should be specified for pedestal

style fittings or when cabling will be pulled through the activation point.

WIREMOLD®

Infloor Duct System

n Heavy Duty Junction Box. Perfect for casino applications,

heavy duty junction boxes are available for applications

where the duct system will be subjected to heavy loads.

n Quality construction. Duct is made of 16 gauge galvannealed

steel with continuous seam weld construction. Makes for easy

field cuts and prevents water seepage into the duct.

n Large bend radius into duct and around corners and elbows.

Maintains integrity of fiber optic cable when changing direction

of cable orientation.

n Large oblong opening into duct. Allows easy hand access

into the duct to pull wires. The opening provides enhanced

bend radius when pulling cable.

n One-meter fiber or cable loop storage in preset. Allows

easy access to cable to activate service fitting.

n Flush activations for single-, double-, and triple-duct runs

for both tiled and carpeted floors. Aesthetically pleasing

activations in brass, brushed aluminum and nonmetallic

provide easy access to power and telecommunications at

each workstation. Activations accept Category 6, 5e, UTP,

STP, coaxial, audio, and fiber optics inserts. Front loaded

snap-in inserts save installation time.

n Only junction box offering square or round

access cover plates. The flexibility to choose which

style will provide the best aesthetic appearance

for a particular tile or carpet application.

n Built-in tile trim. The square junction boxes include flangeless

aluminum trim to accommodate 1/8" [3.2mm] thick tile.

n Large presets. The presets have large cubic inch capacity

to allow easy access to wires and plenty of room for

splicing and connections. Saves installation time.

Highly flexible duct system to meet

varying project demands

FEATURES & BENEFITS

Walkerduct® Underfloor Duct System includes two sizes of underfloor

ducts - No.2 and No. 4 - for maximum flexibility. This allows you to match

cable capacity to project demands by combining several ducts of different

sizes in the same system. It’s an ideal configuration for casinos, commercial

offices, education, government, museums, and retail applications.

Walkerduct features superior product construction, manufactured of

16-gauge galvannealed steel with continuous seam welds. It accepts a

wide variety of service fittings, including flush and pedestal styles.

Ducts are available with or without presets. Pro Series presets are

rectangular and accommodate flush and pedestal service fittings while

providing ample bend radius to ensure the integrity of fiber optic cable

connections. IPS presets are round and offer smaller egress areas.

These work with pedestal style activations and are ideal for furniture

feed applications. See page 17 for more information on compatible

service fittings.

Walkerduct can be fed by junction boxes or by Trenchduct for larger

cable capacity installations.

Pro Series presets can be positioned together to

create one activation location.

1 Duct

2 Pro Series Preset

3 Junction Box

4 Coupling

5 Duct Support

6 Conduit Adapter

7 Elbow

8 Junction Box Closure

NOTE: Illustration is for showing

product applications only.

WALKERDUCT PRO SERIES SYSTEM LAYOUT WITH JUNCTION BOXES

KEY

1 Trenchduct

2 #2 2" IPS Duct

3 #4 2" IPS Duct

4 Cross Under

5 Couplings

6 End Closure

7 Support

8 Horizontal Flat Elbow

9 Vertical Elbow

10 Blank #4 Duct

WALKERDUCT 2" [51MM] IPS DUCT SYSTEM LAYOUT WITH TRENCHDUCT

KEY

Walkerduct Pro Series System Layouts

NOTE: Illustration is for showing

product applications only.

NOTE: Part numbers ending in a dash need to have the height adjustment size suffix included when

ordering. Please see the individual support product descriptions for this information.

Adjustable Support

Couplings SC12- SC14- SC222- SC224- SC244- SC3222- SC3224- SC3244- SC3424- *

Hold-Down Straps HS12 HS14 HS222 HS224 HS244 HS3222 HS3224 HS3244 HS3424 *

Couplings 302 H302 302 302 H302 302 302 302 302 H302

H302 H302 H302 H302

Duct End Closures 304 H304 304 304 H304 304 304 304 304 H304

H304 H304 H304 H304

Buy America BA-S12- BA-S14- BA-S222- BA-S224- BA-S244-

BA-S3222- BA-S3224- BA-S3244- BA-S3424-

Supports

Conduit Adapters 312- H312- 312- 312- H312- 312- 312- 312- 312- H312-

314- H317- 314- 314- H317- 314- 314- H312- 314- H317-

317- H322- 317- 317- H322- 317- 317- 314- 317- H322-

322- 322- 322- 322- H317- 317- H317-

324- 324- 324- 324- 322- H317- 322-

H322- H322- 322- H322-

H317- 324- H322- 324-

H312- H312- 324- H312-

Box Corner

Conduit Adapter 255- 255- 255- 255- 255- 255- 255- 255- 255- 255-

Terminal Bushings 334UF H334 334UF 334UF H334 334UF 334UF 334UF 334UF H334

H334 H334 H334 H334

Vertical Elbows 332UF H332 332UF 332UF H332 332UF 332UF 332UF 332UF H332

H332 H332 H332 H332

Horizontal Elbows 338UF H338 338UF 338UF H338 338UF 338UF 338UF 338UF H338

(90° & 45°) 342UF H342 342UF H338 H342 342UF H338 H338 H338 H342

342UF 342UF 342UF 342UF

H342 H342 H342 H342

Crossunder Offsets 372 H372 372 372 H372 372 372 372 372 H372

375 H375 375 H372 H375 375 H372 H372 H372 H375

375 375 375 375

H375 H375 H375 H375

Expansion Joints 382 H382 382 382 H382 382 382 382 382 H382

H382 H382 H382 H382

Mudcaps 421 421 421 421 421 421 421 421 421 421

Marker Caps 422GR 422GR 422GR 422GR 422GR 422GR 422GR 422GR 422GR 422GR

422RD 422RD 422RD 422RD 422RD 422RD 422RD 422RD 422RD 422RD

Box Opening Closures 203 H203 203 203 H203 203 203 203 203 H203

H203 H203 H203 H203

Box Closure Adapters — 275SL

— 275SL 275SL — 275SL 275SL 275SL 275SL

275SR 275SR 275SR 275SR 275SR 275SR 275SR

Sealant 290G 290G 290G 290G 290G 290G 290G 290G 290G 290G

Tile & Carpet square square square square square square square square square square

Trim/Holders FT6- FT10- FT10- FT15- FT18- FT15- FT18- FT21- FT21- FT25-

CT6- CT10- CT10- CT15- CT18- FT15- FT18- FT21- FT21- FT25-

round round round round round round round round round round

SFCS5- SFCS9- SFCS9- SFCS14- SFCS17- SFCS14- SFCS17- SFCS20- SFCS20- SFCS24-

SFCB5- SFCB9- SFCB9- SFCB14- SFCB17- SFCB14- SFCB17- SFCB20- SFCB20- SFCB24-

Junction Box 212- H232- 212- 212- H232 212 212 212 212 H232

Conduct Adapters 232- 232- 232- 232 232 232 232

H232- H232 H232 H232

Accessories

12 System

14 System

222 System

224 System

244 System

3222 System

3224 System

3244 System

3424 System

3444 System

Walkerduct Duct Systems provide wire management for

open space environments while maintaining aesthetics

because they are buried in the floor, out of sight, and

safe from abuse. The duct is designed to be used with

Walkerduct Junction Boxes or Trenchduct to create an

infloor wire management system. Duct runs provide a

range of capacities to suit any situation and to future

proof the wire management system. Duct can be used

individually or combined with other duct to deliver

power and communication services to workstations.

Multiple duct runs may be all one size of duct or a mix

of sizes. Activations may be located anywhere along

the length of the duct to maximize flexibility and

accessibility to wiring workstations. Flexibility is only

limited by the grid pattern. Walkerduct Duct Systems are

designed to be used with power and communications

service fittings.

12"

[305mm]

12"

[305mm]

12"

[305mm]

12"

[305mm]

12"

[305mm]

12"

[305mm]

12"

[305mm]

12"

[305mm]

12"

[305mm]

[152mm]

10'

[3m]

10'

[3m]

24"

[610mm]

24"

[610mm]

24"

[610mm]

24"

[610mm]

12"

[305mm]

12"

[305mm]

10'

[3m]

Walkerduct Pro Series System Accessories

j∆

Catalog No. /Item Description/Specifications

2-0 No. 2 Duct Blank Duct – Used primarily for

4-0 No. 4 Duct feeder runs. 10' [3m] standard

length. One-piece continuous

seam weld construction.

16 gauge [1.5mm]

galvannealed steel.

D21210 No. 2 Duct, 12" spacing, 1" presets. Pro Series

Preset Duct

–

Used for

D21215 No. 2 Duct, 12" spacing, 1 1/2" presets.

distribution

runs. 10' [3m] standard

D21220 No. 2 Duct, 12" spacing, 2 " presets.

length. One-piece continuous seam weld

D21225 No. 2 Duct, 12" spacing, 2 1/2" presets.

construction. 16 gauge galvannealed

D21230 No. 2 Duct, 12" spacing, 3" presets. steel. Die-cast presets have

D22410 No. 2 Duct, 24" spacing, 1" presets. knockout in base. With knockout

D22415 No. 2 Duct, 24" spacing, 1 1/2" presets. removed, the opening size into

D22420 No. 2 Duct, 24" spacing, 2" presets.

duct is 3 1/8" x 1 5/8" [79mm x 41mm].

D22425 No. 2 Duct, 24" spacing, 2 1/2" presets. No. 4 duct is punched off center.

D22430 No. 2 Duct, 24" spacing, 3" presets. An alignment clip is included with

each pair of presets. This is used

D41210 No. 4 Duct, 12" spacing, 1" presets. to connect presets and prevent

D41215 No. 4 Duct, 12" spacing, 1 1/2" presets. movement of presets during

D41220 No. 4 Duct, 12" spacing, 2" presets. concrete pour.

D41225 No. 4 Duct, 12" spacing, 2 1/2" presets.

D41230 No. 4 Duct, 12" spacing, 3" presets. Standard preset spacings are

D42410 No. 4 Duct, 24" spacing, 1" presets. 12" [305mm] and 24" [610mm]

D42415 No. 4 Duct, 24" spacing, 1 1/2" presets. on center. Preset heights are:

D42420 No. 4 Duct, 24" spacing, 2" presets. 1" [25mm], 1 1/2" [38mm], 2"

D42425 No. 4 Duct, 24" spacing, 2 1/2" presets. [51mm], 2 1/2" [64mm], and

D42430 No. 4 Duct, 24" spacing, 3" presets. 3" [76mm]. Presets are sealed

with recessed removable mudcap.

Preset dimensions are 4 1/8" wide

x 4 13/16" long [105mm x 123mm].

Service fitting selections for Pro

Series preset duct are: 525 Series,

Multiplex Series, Pro Series, PSRC9

Series, and Source I Series. See

page 17 for more information.

421

Pro Series Mudcap – Steel

replacement cap for preset.

Recessed to hold 3/8" [9.5mm] concrete.

422GR (Green) Marker Cap – Replaces mudcap

422RD (Red) on preset to indicate location of

the last insert in each run.

Select color for each service.

425 1/2" [12.1mm] High Pro Series Preset Extensions –

426 1" [25mm] High Can be factory or field installed to

increase height of presets. Die-cast

construction. Attaches with push on

metal sleeves (included). 1" [25mm]

size can be stacked. 1/2" [12.7mm]

size cannot be stacked with another

extension on top.

D2075 For No. 2 Duct 12" Section of Duct with 1" Pro

D4075 For No. 4 Duct Series Preset and Duct Conduit

Hub– For rigid or PVC conduit.

Used to provide feed to isolated

outlets; maintains 24" [610mm]

spacing of presets. Preset height

is 1" [25mm]. Add extensions if

higher preset needed.

Walkerduct Ordering Information

3 1/8" x 1 1/4"

[79mm x 32mm]

2-0

4-0

6 1/2" x 1 1/2"

[165mm x 38mm]

No. 4 Duct with 24"

[610mm] Spacing

No. 2 Duct with 12"

[305mm] Spacing

Alignment Clip

End View with Alignment Clip in Place

3.34 Sq. In. [21.5cm2] 8.72 Sq. In. [56.3cm2]

Catalog Numbering System:

Example: D21215

Duct Preset Height

Size of Duct Preset Spacing

IMPORTANT!

A minimum 1 1/2" [38mm] preset or afterset is required on Pro Series duct to support standard

duplex receptacles and communication devices when using flush activations. The

1" [25mm] preset or afterset should be specified for pedestal style fittings or when cabling will

be pulled through the activation point.

IMPORTANT!

Triple-gang flush activations are

not compatible with 3244 and 3444

System layouts. Use combination of

single- and two-gang activations to

access all three ducts at one point.

Pro Series Marker Cap – Replaces

mudcap on preset to indicate

location of the last insert in each

run. Select color for each service.

Catalog No. /Item Description/Specifications

2-12x2x7/8 No. 2 Duct, 12" spacing, 7/8" presets. IPS Preset Duct – Used for distribution runs. 10'

2-12x2x11/2 No. 2 Duct, 12" spacing, 1 1/2" presets. [3m] standard length. One-piece continuous

2-12x2x2 No. 2 Duct, 12" spacing, 2" presets. seam weld construction. 16 gauge galvannealed

2-12x2x21/2 No. 2 Duct, 12" spacing, 2 1/2" presets. steel. Round die-cast presets have inside

2-12x2x3 No. 2 Duct, 12" spacing, 3" presets. threads to accept standard connectors.

2-24x2x7/8 No. 2 Duct, 24" spacing, 7/8" presets. Standard preset spacings are 12" [305mm] and

2-24x2x11/2 No. 2 Duct, 24" spacing, 1 1/2" presets. 24" [610mm] on center. Preset heights are 7/8"

2-24x2x2 No. 2 Duct, 24" spacing, 2" presets. 1 1/2", 2", 2 1/2" and 3" [22.2mm, 38mm, 51mm,

2-24x2x21/2 No. 2 Duct, 24" spacing, 2 1/2" presets. 64mm and 76mm]. Presets are sealed with

2-24x2x3 No. 2 Duct, 24" spacing, 3" presets. recessed removable mudcap. Preset inside

diameter is 2" [51mm].

4-12x2x7/8 No. 4 Duct, 12" spacing, 7/8" presets.

4-12x2x11/2 No. 4 Duct, 12" spacing, 1 1/2" presets. Service fitting selections for 2" [51mm] IPS

4-12x2x2 No. 4 Duct, 12" spacing, 2" presets. preset duct are: 525 Series, Multiplex, and

4-12x2x21/2 No. 4 Duct, 12" spacing, 2 1/2" presets. 1200 Series. See page 17 for more information.

4-12x2x3 No. 4 Duct, 12" spacing, 3" presets.

4-24x2x7/8 No. 4 Duct, 24" spacing, 7/8" presets.

4-24x2x11/2 No. 4 Duct, 24" spacing, 1 1/2" presets.

4-24x2x2 No. 4 Duct, 24" spacing, 2" presets.

4-24x2x21/2 No. 4 Duct, 24" spacing, 2 1/2" presets.

4-24x2x3 No. 4 Duct, 24" spacing, 3" presets.

404 IPS Mudcap – Steel replacement cap for 2"

[51mm] IPS preset. Recessed to hold 3/8"

[9.5mm] concrete.

415B (Brass) IPS Marker Cap – Replaces mudcap on preset to

415N (Steel) indicate location of run. NEC requires markers

to locate the last preset in each run. Select color

for each service.

317-3/4-* For No. 2 Duct 2' [610mm] Section of Duct with IPS Preset

H317-3/4-* For No. 4 Duct and 3/4" [19.1mm] Conduit Hub – For rigid or

PVC conduit. Used to provide feed to isolated

outlets; maintains 24" [610mm] spacing of

presets. Heights from 7/8" [22.2mm] to

3 1/2" [89mm]. *Specify preset height.

SIZE

O.D. AREA (SQ IN) 40% FILL*

CABLE/WIRE SIZE NO. 2 NO. 4

Inches [mm] Inches [mm] DUCT DUCT

UNSHIELDED TWISTED PAIR

4-PAIR, 24 AWG CAT 5 .220 [5.6] .038 [24.5] 36 91

4-PAIR, 24 AWG CAT 6 .250 [6.4] .049 [31.7] 27 71

TELEPHONE

2-PAIR, 24 AWG .140 [3.6] .015 [9.9] 89 232

4-PAIR, 24 AWG .190 [4.8] .028 [18.1] 47 124

25-PAIR, 24 AWG .410 [10.4] .132 [85.2] 10 26

COAXIAL

RG58/U .195 [4.9] .030 [19.4] 44 116

RG59/U .242 [6.1] .046 [29.7] 29 75

RG6/U .270 [6.8] .057 [36.8] 23 61

SHIELDED TWISTED PAIR

TYPE 1 .390 [9.9] .119 [76.8] 11 29

TYPE 2 .465 [11.8] .170 [109.7] 7 20

TYPE 3 .245 [6.2] .047 [30.3] 28 74

FIBER OPTIC

2-STRAND .180 [4.6] .025 [16.1] 53 139

4-STRAND .190 [4.8] .028 [18.1] 47 124

6-STRAND .210 [5.3] .035 [22.6] 38 99

FIBER ZIPCORD .110 [2.8] .010 [6.5] 133 348

THHN WIRE

#14 0.111 [2.8] .0097 [6.3] 137 359

#12 0.130 [3.3] .0133 [8.6] 100 262

#10 0.164 [4.2] .0211 [13.6] 63 165

# 8 0.216 [5.5] .0366 [23.6] 36 95

# 6 0.254 [6.5] .0507 [32.7] 26 68

# 4 0.324 [8.2] .0824 [53.2] 16 42

Cable Size/Wire Fill Chart

*40% cable fill is the maximum cable allowed by NEC.

Walkerduct Ordering Information

Catalog Numbering System:

Example: 2-24 x 2 x 2

Duct Preset Height

Preset Spacing 2" [51mm] IPS

No. 2 Duct with 12"

[305mm] Spacing

No. 4 Duct with 24"

[610mm] Spacing

12"

[30mm]

24"

[610mm]

Catalog No./Item Description/Specifications

HS12 For one No. 2 Duct Hold-Down Straps – To fasten ducts

HS14 For one No. 4 Duct to the slab in shallow concrete. Used

HS222 For two No. 2 Ducts in place of duct supports. Straps

HS224 For one No. 2 Duct maintain 1" [25mm] spacing

and one No. 4 Duct between ducts on multiple duct

HS244 For two No. 4 Ducts runs and prevent duct from floating

HS3222 For three No. 2 Ducts during concrete pour. Attaches to

HS3224 For two No. 2 Ducts slab with stakes or drive pins (not

and one No. 4 Duct included). Locate hold-down straps

HS3244 For one No. 2 Duct on approximate 5' [1.5m] centers.

and two No. 4 Ducts

HS3424 For two No. 4 Ducts with

one No. 2 Duct in center

Catalog No./Item Description/Specifications

SC12 For one No. 2 Duct Adjustable Duct Supports with Built-In

SC14 For one No. 4 Duct Couplings – To support, couple, and hold

SC222 For two No. 2 Ducts duct in place before and during concrete

SC224 For one No. 2 Duct pour. Steel construction. Leveling screws

and one No. 4 Duct provide vertical adjustment. Different

SC244 For two No. 4 Ducts leg heights available. Supports may

SC3222 For three No. 2 Ducts be fastened to form or to slab through

SC3224 For two No. 2 Ducts holes in the feet. Top members

and one No. 4 Duct maintain 1" [25mm] spacing between

SC3244 For one No. 2 Duct ducts. Locate duct supports on

and two No. 4 Ducts approximately 5' [1.5m] intervals.

SC3424 For two No. 4 Ducts

and one No. 2 Duct

(No. 2 Duct in center)

Support Couplings Ordering Information

Hold-Down Straps Ordering Information

How to Determine Correct

Support Heights

A Height of preset.

B Height of duct.

C Distance from bottom of duct to

form or slab. This dimension is

the correct support height.

D Distance between finished concrete

floor line and floor slab. This

dimension is the sum total of

A, B, and C.

Support Height (C) = D - (A and B)

SC14

Two Holes 9/32"

[7.1mm] Dia.

APreset

Duct

Catalog Numbering System:

Example:

SC3244

Support

No. of Ducts Duct Size

in System and Orientation

HS3224

[25mm]

1 5/8"

[41mm]

HS14

3/4"

[19.1mm]

*Cat. No. Suffix Height Adjustment

-18 1/2" [12.7mm] to 1 7/8" [48mm]

-33 1 1/2" [38mm] to 3 3/4" [95mm]

-48 3" [76mm] to 4 7/8" [124mm]

Duct supports for deeper pours are available through

the factory.

NOTE: Recommend minimum of 3" [76mm]

clearance space on each side

of duct support (E dimension)

for concrete placement.

Cat No. DIMENSION “E”

Inches [mm]

SC12 8.125 [206mm]

SC14 11.500 [292mm]

SC222 12.250 [311mm]

SC224 15.625 [396mm]

SC244 19.000 [482mm]

SC3222 16.375 [415mm]

SC3224 19.750 [501mm]

SC3242 19.750 [501mm]

SC3244 23.125 [587mm]

SC3444 26.500 [673mm]

SC42222 20.500 [520mm]

SC222

SC3222

No. 2 Duct strap is 1 1/4" H [32mm]; No.

4 Duct strap is 1 1/2" H [38mm]; Straps

have a maximum width of 1 1/4" [32mm].

ITEM “E” DIMENSION

HS12 5 3/16" [132mm]

HS14 8 1/16" [205mm]

HS222 10 5/8" [270mm]

HS224 14" [356mm]

HS244 17 3/8" [448mm]

HS3222 14 13/16" [376mm]

HS3224 18 3/16" [462mm]

HS3244 21 9/16" [548mm]

HS3424 21 9/16" [548mm]

5 3/4" D

[146mm]

2 13/16" R

[71mm]

10 1/2"

[267mm]

10 1/2"

[267mm]

Catalog No./Item Description/Specifications

338UF 90° Horizontal Elbow –

Creates 90° horizontal

turn in No. 2 Duct.

H338 90° Horizontal Elbow –

Creates 90° horizontal

turn in No. 4 Duct.

H338AU-1 90° Horizontal Elbow with

Access Unit – Used to make

90° horizontal turn in No. 4

Duct. Access cover can be

removed to facilitate wire

pulling. For concrete pours

over 1" [25mm] an extension

ring is required. See Cat. No.

6AER- rings on page 9.

342UF

Adjustable Horizontal Elbow –

No. 2 Duct elbow angled for

45° turn. Angle may be varied

from 22 1/2° to 67 1/2° by

cutting duct ends at

different angles.

H342

Adjustable Horizontal Elbow

–

No. 4 Duct elbow angled for

45° turn. Angle may be

varied from 22 1/2° to

67 1/2° by cutting duct ends at

different angles.

372 For No. 2 Duct Offset – Used to raise or

H372 For No. 4 Duct lower a run of duct by 1 5/8"

[41mm]. Two required for

crossunders. Used with

field-cut blank duct.

Catalog No./Item Description/Specifications

BA-S12 Adjustable Duct Support –

BA-S14 Adjustable Duct Supports are

BA-S222 used to hold the duct securely

BA-S224 in place before and during the

BA-S244 concrete pour. Unlike the SC

BA-S3222 Series Support Couplings, they

BA-S3224 must be used with a separate

BA-S3244 Coupling. Locate duct supports

BA-S3424 on approximately 5' [1.5m]

intervals. Select coupling 302

for #2 duct and H302 for #4 duct.

302 Coupling – To couple two

No. 2 Ducts.

A = 3 1/4" [83mm];

B = 1 3/8" [38mm].

H302 Coupling – To couple two

No. 4 Ducts.

A = 6 9/16" [167mm];

B = 1 9/16" [40mm].

304 Duct End Plug – To seal

end of No. 2 Duct.

A = 3 1/8" [79mm];

B = 1 1/4" [32mm].

H304 Duct End Plug – To seal

end of No. 4 Duct.

A = 6 1/2" [165mm];

B = 1 1/2" [38mm].

334UF Panel Connector – Secures

No. 2 Duct to cabinet.

H334 Panel Connector – Secures

No. 4 Duct to cabinet.

332UF 90° Vertical Elbow – Creates

90° vertical turn in No. 2 Duct.

H332 90° Vertical Elbow – Creates

90° vertical turn in No. 4 Duct.

8 1/2"

[216mm]

8 1/2"

[216mm]

3" R

[76mm]

21 7/8"

[556mm]

8 1/2" R

[216mm]

21 7/8"

[556mm]

7/8"

[22.2mm]

3 5/16"

[84mm] 7 11/16"

[195mm]

5 1/8"

[130mm]

5 1/8"

[130mm]

2 5/16" R

[59mm]

Duct Closures, Elbows and Offsets Ordering Information

4 1/8"

[105mm]

2 3/4"

[70mm]

3 7/16"

[87mm]

1 5/8"

[41mm]

6 3/8"

[162mm]

3" R

[76mm]

Min. Offset

[127mm]

45°

3" R

[76mm]

5 1/2"

[140mm]

Min. Offset

2 13/16" R

[71mm]

10 1/2"

[267mm]

10 1/2"

[267mm]

5.375

1.500

Catalog No./Item Description/Specifications

375 For No. 2 Duct Variable Offset – Used

H375 For No. 4 Duct to raise or lower a run of

duct from 5/16" [7.9mm]

to 3 1/2" [89mm]. Field

cut duct based on

chart below.

Catalog No./Item Description/Specifications

300-4 Adapter Coupling – Couples

No. 2 Duct to No. 4 Duct.

382 For No. 2 Duct Expansion Joint Sleeves –

H382 For No. 4 Duct Slip over two sections of

duct. Outside screws fasten

and ground sleeves to duct.

Amount of expansion is

determined by gap allowed

between duct sections.

[76mm] 3"

[76mm]

3 9/16"

[90mm]

6 15/16"

[176mm]

[152mm]

Duct Closures, Elbows and Offsets Ordering Information (Continued)

5/16" [7.9mm]

3/8" [9.5mm]

7/16" [11.1mm]

1/2" [12.7mm]

9/16" [14.3mm]

5/8" [15.9mm]

11/16" [17.5mm]

3/4" [19.1mm]

13/16" [20.6mm]

7/8" [22.2mm]

15/16" [23.8mm]

1 3/8" [35mm]

1 3/4" [44mm]

2 1/8" [54mm]

2 1/2" [64mm]

2 7/8" [73mm]

3 1/4" [83mm]

3 1/2" [89mm]

3 7/8" [98mm]

4 1/4" [108mm]

4 5/8" [118mm]

5" [127mm]

1" [25mm]

1 1/4" [32mm]

1 1/2" [38mm]

1 3/4" [45mm]

2" [51mm]

2 1/4" [57mm]

2 1/2" [64mm]

2 3/4" [70mm]

3" [76mm]

3 1/4" [83mm]

3 1/2" [89mm]

5 3/8" [137mm]

6 13/16" [173mm]

8 1/4" [210mm]

9 11/16" [246mm]

11 1/4" [286mm]

12 9/16" [319mm]

14" [356mm]

15 7/16" [392mm]

16 7/8" [429mm]

18 5/16" [465mm]

19 3/4" [502mm]

FOR DUCT CUT FOR DUCT CUT

OFFSET (LENGTH) OFFSET (LENGTH)

10°

Duct

5/8"

[15.9mm] 5/8"

[15.9mm]

Catalog No./Item Description/Specifications

324-3/4 Male Conduit Adapter –

Fits into end of No. 2 Duct.

For two 3/4" trade size

rigid or PVC conduits.

H312-3/4 [19.1mm] Female Conduit Adapter –

-1 [25mm] Fits on outside of No. 4

-11/4 [32mm] Duct. For one rigid or PVC

-11/2 [38mm] conduit. H322-11/2 with

-2 [51mm] one opening plugged is

used for H312-11/2.

Note: For H312-2 this dimension

is 2 1/2" [64mm].

H322-1 [25mm] Female Conduit Adapter –

-11/4 [32mm] Fits on outside of No. 4

-11/2 [38mm] Duct. For two rigid or PVC

-2 [51mm] conduits. Suffix indicates

conduit trade size.

Catalog No./Item Description/Specifications

312-3/4 [19.1mm] Female Conduit Adapter –

-1 [25mm] Fits on outside of No. 2

-11/4 [32mm] Duct. For one rigid or

-11/2 [38mm] PVC conduit.

-2 [51mm]

314-3/4 Male Conduit Adapter –

Fits into end of No. 2 Duct.

For one 3/4" trade size

rigid or PVC conduit.

322-11/4 [32mm] Female Conduit Adapter –

-11/2 [38mm] Fits on outside of No. 2

Duct. For two rigid or PVC

conduits. Suffix indicates

conduit trade size.

3 1/2"

[89mm]

Duct Conduit Adapters Ordering Information

[76mm]

1 3/4"

[44mm]

1 1/4"

[32mm]

3 1/2"

[89mm]

[76mm]

1 1/8"

[29mm]

7 1/8"

[181mm]

[76mm]

[178mm]

2 1/8"

[54mm]

3 1/2"

[89mm]

Purpose:

Junction boxes are used at intersections of duct runs to:

1. To separate the various raceways as they cross each other.

2. To furnish access to the system for pulling and splicing of wires.

3. To provide means of connecting the system to distribution closets

with duct or conduit home runs.

Construction Features:

Openings are provided in the four sides to receive from one to five ducts, which

are secured by grounding clips. Corner openings provide conduit feeds.The interiors

of the boxes have partitions which completely separate each duct and at the same

time form a continuous path through the box in both directions. No partitions are needed

for single run boxes. Most partitions are removable and their orientation can be changed

to correct installation errors. For precise leveling after the pour, cover plates can be

adjusted upward 1/2" [12.7mm] with the recessed screws in the cover plate.

Standard boxes are designed for use with duct having 1" [25mm] high presets. Boxes with higher side rails

in 1/2" [12.7mm] increments can be furnished for systems requiring higher presets. Cover plates are

1/4" [6.4mm] thick. Junction boxes are provided with nonmetallic corner inserts to provide controlled

cable bend radius around the tunneling inside the box (see diagram). They should be snapped into

place before wire placement. Brass or stainless steel holders for tile and carpet can be used on top

of the round cover plates. Square junction boxes include aluminum trim for carpet or tile applications.

Heavy duty junction boxes are used where heavy loads will be rolled over or placed on the system. These are constructed with a 3/8" [9.5mm]

cover plate and additional support studs. Up to 5/8" [15.9mm] concrete recommended over presets for heavy loads. Minimum heavy duty

junction box height is 1 1/2" [38mm].

Item Catalog No./Description/Specifications

12JS-* (square cover plate) Junction Box – One No. 2 Duct per

12JR-* (round cover plate) side. No interior partitioning. Square

cover plate measures 6 3/4" x 6 3/4"

12HS-* Heavy duty (square) [171mm x 171mm]. Diameter of

12HR-* Heavy duty (round) round cover plate is 4.813" [122mm].

Specify suffix.

[178mm]

6 3/4"

[172mm] 2 9/16"

[65mm]

1 5/8"

[41mm]

11 3/8"

[289mm]

15/16" [23.8mm]

*SUFFIX FOR JUNCTION BOXES DEPTH OF CONCRETE OVER DUCT

1 1" [25mm] min. to 1 1/2" [35mm] max.

1 1/2 1 1/2" [38mm] min. to 2" [51mm] max.

2 2" [51mm] min. to 2 1/2" [62mm] max.

2 1/2 2 1/2" [64mm] min. to 3" [76mm] max.

3 3" [76mm] min. to 3 1/2" [89mm] max.

3 1/2 3 1/2" [89mm] min. to 4" [102mm] max.

Catalog No./Item Description/Specifications

4210 1" [25mm] high Afterset – Installed either before or after concrete pour to create

4215 1 1/2" [38mm] high activation from duct. Requires 6 1/2" [165mm] core drilled hole in

4220 2" [51mm] high concrete and 2 1/2" [64mm] diameter hole in duct. Requires grout fill

4225 2 1/2" [64mm] high around afterset to fill voids in 6 1/2" [165mm] hole. Attaches to duct with

4230 3" [76mm] high locking tabs. Extensions can be attached to increase height. Aftersets

4235 3 1/2" [89mm] high are gangable. Alignment clip and mudcap included. All Pro Series

activations fit on afterset. See ED850 and ED667.

436-2-7/8 7/8" [22.2mm] high Round Afterset – Installed either before or after concrete pour

-2-1 1/2 1 1/2" [38mm] high to create activation from duct. Requires 2 1/2" [64mm] core

-2-2-2 2" [51mm] high drilled hole in concrete and 2 1/4" [57mm] diameter hole in duct.

-2-2 3/8 2 3/8" [64mm] high Attaches to duct with locking tabs. Extensions can be attached

-2-3 3" [76mm] high to increase height.

Aftersets Ordering Information

Walkerduct Junction Boxes Ordering Information

Cable Bend

Control Inserts

Aluminum Trim

Square Cover Plate Round Cover Plate

4 13/16"

[123mm] 4 1/8"

[105mm]

IMPORTANT!

A minimum 1 1/2" [38mm] preset or afterset is required on Pro Series duct to

support standard duplex receptacles and communication devices when using flush

activations. The 1" [25mm] preset or afterset should be specified for pedestal style

fittings or when cabling will be pulled through the activation point.

*Other junction box heights are available. Consult factory for availability.

1010

Item Catalog No./Description/Specification

14JS-* (square cover plate) Junction Box – One No. 4 duct per

14JR-* (round cover plate) side. No interior partitioning. Square

cover plate measures 10 7/8" x 10 7/8"

14HS-* Heavy Duty (square) [276mm x 276mm]. Diameter of round

14HR-* Heavy Duty (round) cover plate is 8.948" [227mm].

Specify suffix.

222JS-* (square cover plate) Junction Box – Two No. 2 ducts per

222JR-* (round cover plate) side. Square cover plate measures

10 7/8" x 10 7/8" [276mm x 276mm].

222HS-* Heavy Duty (square) Diameter of round cover plate is

222HR-* Heavy Duty (round) 8.948" [227mm]. Specify suffix.

224JS-* (square cover plate) Junction Box – One No. 2

224JR-* (round cover plate) duct and one No. 4 duct per side.

Square cover plate measures 15"

224HS-* Heavy Duty (square) x 15" [381mm x 381mm]. Diameter

224HR-* Heavy Duty (round) of round cover plate is 13.063"

[332mm]. Specify suffix.

244JS-* (square cover plate) Junction Box – Two No. 4 ducts

244JR-* (round cover plate) per side. Square cover plate

measures 18 3/8" x 18 3/8"

244HS-* Heavy Duty (square) [467mm x 467mm]. Diameter

244HR-* Heavy Duty (round) of round cover plate is 16.438"

[418mm]. Specify suffix.

Walkerduct Junction Boxes Ordering Information (Continued)

18 5/8"

[473mm]

2 9/16"

[65mm]

25"

[584mm]

1 5/8"

[41mm]

15/16"

[23.8mm]

18 3/8"

[467mm]

*SUFFIX FOR JUNCTION BOXES DEPTH OF CONCRETE OVER DUCT

1 1" [25mm] min. to 1 1/2" [35mm] max.

1 1/2 1 1/2" [38mm] min. to 2" [51mm] max.

2 2" [51mm] min. to 2 1/2" [62mm] max.

2 1/2 2 1/2" [64mm] min. to 3" [76mm] max.

3 3" [76mm] min. to 3 1/2" [89mm] max.

3 1/2 3 1/2" [89mm] min. to 4" [102mm] max.

*SUFFIX FOR JUNCTION BOXES DEPTH OF CONCRETE OVER DUCT

1 1" [25mm] min. to 1 1/2" [35mm] max.

1 1/2 1 1/2" [38mm] min. to 2" [51mm] max.

2 2" [51mm] min. to 2 1/2" [62mm] max.

2 1/2 2 1/2" [64mm] min. to 3" [76mm] max.

3 3" [76mm] min. to 3 1/2" [89mm] max.

3 1/2 3 1/2" [89mm] min. to 4" [102mm] max.

*SUFFIX FOR JUNCTION BOXES DEPTH OF CONCRETE OVER DUCT

1 1" [25mm] min. to 1 1/2" [35mm] max.

1 1/2 1 1/2" [38mm] min. to 2" [51mm] max.

2 2" [51mm] min. to 2 1/2" [62mm] max.

2 1/2 2 1/2" [64mm] min. to 3" [76mm] max.

3 3" [76mm] min. to 3 1/2" [89mm] max.

3 1/2 3 1/2" [89mm] min. to 4" [102mm] max.

*SUFFIX FOR JUNCTION BOXES DEPTH OF CONCRETE OVER DUCT

1 1" [25mm] min. to 1 1/2" [35mm] max.

1 1/2 1 1/2" [38mm] min. to 2" [51mm] max.

2 2" [51mm] min. to 2 1/2" [62mm] max.

2 1/2 2 1/2" [64mm] min. to 3" [76mm] max.

3 3" [76mm] min. to 3 1/2" [89mm] max.

3 1/2 3 1/2" [89mm] min. to 4" [102mm] max.

*Other junction box heights are available. Consult factory for availability.

11 1/8"

[283mm]

2 9/16"

[65mm]

1 5/8"

[41mm]

15/16"

[23.8mm]

15 1/2"

[394mm]

10 7/8"

[276mm]

11 1/8"

[283mm]

2 9/16"

[65mm]

1 5/8"

[41mm]

15/16"

[24mm] 10 7/8"

[276mm]

15 1/2"

[394mm]

15 1/4"

[387mm]

2 9/16"

[65mm]

19 5/8"

[499mm]

1 5/8"

[41mm]

15/16"

[23.8mm]

15" [381mm]

1111

Item Catalog No./Description/Specifications

3222JS-* (square cover plate) Junction Box – Three No. 2

3222JR-* (round cover plate) Ducts per side. Square cover

plate measures 15" x 15"

3222HS-* Heavy Duty (square) [381mm x 381mm]. Diameter

3222HR-* Heavy Duty (round) of round cover plate is 13.063"

[332mm]. Specify suffix.

3224JS-* (square cover plate) Junction Box – Two No. 2

3224JR-* (round cover plate) Ducts and one No. 4 duct per

side. Square cover plate measures

3224HS-* Heavy Duty (square) 18 3/8" x 18 3/8" [467mm x 467mm].

3224HR-* Heavy Duty (round) Diameter of round cover plate is

16.438" [418mm]. Specify suffix.

3424JS-* (square cover plate) Junction Box – Two No. 4 Ducts and

3424JR-* (round cover plate) one No. 2 Duct per side. The No. 2

Duct is centered between the two

3424HS-* Heavy Duty (square) No. 4 Ducts. Square cover plate

3424HR-* Heavy Duty (round) measures 21 3/4" x 21 3/4"

[553mm x 553mm]. Diameter of

round cover plate is 19.813"

[503mm]. Specify suffix.

3244JS-* (square cover plate) Junction Box – One No. 2

3244JR-* (round cover plate) Duct and two No. 4 Ducts per

side. Square cover plate measures

3244HS-* Heavy Duty (square) 21 3/4"x 21 3/4" [553mm x 553mm].

3244HR-* Heavy Duty (round) Diameter of round cover plate is

19.813". [503mm]. Specify suffix.

Walkerduct Junction Boxes Ordering Information (Continued)

*SUFFIX FOR JUNCTION BOXES DEPTH OF CONCRETE OVER DUCT

1 1" [25mm] min. to 1 1/2" [35mm] max.

1 1/2 1 1/2" [38mm] min. to 2" [51mm] max.

2 2" [51mm] min. to 2 1/2" [62mm] max.

2 1/2 2 1/2" [64mm] min. to 3" [76mm] max.

3 3" [76mm] min. to 3 1/2" [89mm] max.

3 1/2 3 1/2" [89mm] min. to 4" [102mm] max.

*SUFFIX FOR JUNCTION BOXES DEPTH OF CONCRETE OVER DUCT

1 1" [25mm] min. to 1 1/2" [35mm] max.

1 1/2 1 1/2" [38mm] min. to 2" [51mm] max.

2 2" [51mm] min. to 2 1/2" [62mm] max.

2 1/2 2 1/2" [64mm] min. to 3" [76mm] max.

3 3" [76mm] min. to 3 1/2" [89mm] max.

3 1/2 3 1/2" [89mm] min. to 4" [102mm] max.

*SUFFIX FOR JUNCTION BOXES DEPTH OF CONCRETE OVER DUCT

1 1" [25mm] min. to 1 1/2" [35mm] max.

1 1/2 1 1/2" [38mm] min. to 2" [51mm] max.

2 2" [51mm] min. to 2 1/2" [62mm] max.

2 1/2 2 1/2" [64mm] min. to 3" [76mm] max.

3 3" [76mm] min. to 3 1/2" [89mm] max.

3 1/2 3 1/2" [89mm] min. to 4" [102mm] max.

*SUFFIX FOR JUNCTION BOXES DEPTH OF CONCRETE OVER DUCT

1 1" [25mm] min. to 1 1/2" [35mm] max.

1 1/2 1 1/2" [38mm] min. to 2" [51mm] max.

2 2" [51mm] min. to 2 1/2" [62mm] max.

2 1/2 2 1/2" [64mm] min. to 3" [76mm] max.

3 3" [76mm] min. to 3 1/2" [89mm] max.

3 1/2 3 1/2" [89mm] min. to 4" [102mm] max.

*Other junction box heights are available. Consult factory for availability.

15 1/4"

[387mm]

2 9/16"

[65mm]

1 5/8"

[41mm]

15/16"

[23.8mm]

15" [381mm]

19 5/8"

[499mm]

18 5/8"

[473mm]

2 9/16"

[65mm]

23"

[584mm]

1 5/8"

[41mm]

15/16"

[23.8mm]

18 3/8" [467mm]

22"

[559mm]

2 9/16"

[65mm]

26 5/8"

[670mm]

1 5/8"

[41mm]

15/16"

[23.8mm]

21 3/4" [553mm]

22"

[559mm]

2 9/16"

[65mm]

1 5/8"

[41mm]

15/16"

[23.8mm]

21 3/4" [553mm]

26 5/8"

[670mm]

1212

Catalog No./Item Description/Specifications

12EXT-* For 12 size boxes Side Rail Extension – Kit to adapt

222EXT-* For 14 or 222 size boxes JS, JR, HS, and HR style junction

3222EXT-* For 224 or 3222 size boxes boxes for deep concrete pours.

3224EXT-* For 244 or 3224 size boxes

3244EXT-* For 3424 or 3244 size boxes Partition extensions are provided with

side rail extensions. Partitions maintain

the separation of services. Field installation

requires some disassembly and reassembly

of the junction box prior to the concrete

pour. Extensions replace entire sides

of boxes. Specify suffix.

6RTT For 142L/14H box Terrazzo Holder – For round JR style

RTT4 For 12JR box junction boxes. Two-piece brass rings mount

RTT8 For 14JR/222JR box to junction box cover plate. Inner ring is filled

RTT13 For 224JR/3222JR box with terrazzo. Screws are recessed into inner

RTT16 For 244JR/3224JR box ring and allow the holder to be removed after

RTT20 For 3244/3424JR box floor is ground and polished. Terrazzo units

hold 3/4" [19.1mm] deep terrazzo, but increase

the height of the junction box by 1 1/4" [32mm].

Junction Box Accessories Ordering Information

*Suffix for Side Depth of Concrete

Rail Extensions Over Duct

1 1/2 1 1/2" [38mm] min. to 2" [51mm] max.

2 2" [51mm] min. to 2 1/2" [62mm] max.

2 1/2 2 1/2" [64mm] min. to 3" [76mm] max.

3 3" [76mm] min. to 3 1/2" [89mm] max.

3 1/2 3 1/2" [89mm] min. to 4" [102mm] max.

Inside Terrazzo Ring

Cover Plate

Outside Terrazzo Ring

Junction Box

Terrazzo

Topping

as Specified

Terrazzo Holder

3/4" [19.1mm]

Inside Depth

Optional Sand Bed

Between Concrete

and Terrazzo

Concrete Fill

Approx. 1/4"

[6.4mm]

Terrazzo Holder

1 1/4" [32mm]

Outside Depth

Pro Series Preset

5 3/4"

[146mm]

Catalog No./Item Description/Specification

14H-1 Hand Hole Access Unit –

Hand hole units are installed on

No. 4 Duct to facilitate feeding

and splicing of wire and cable.

6 15/16" [176mm] distance

between duct ends. 5 3/4"

[146mm] diameter cover plate.

Includes 1" [25mm] standard

extension. For concrete pours

over 1" [25mm] an extension

ring is required.

H14ABD Afterset Access Assembly –

Provides access to pull large

number of cables out of duct at

one activation. Neoprene boot

to protect wires not included.

Requires 5" [127mm] hole in

duct. Can be used as an afterset

or preset on No. 4 Duct. For

concrete pours over 1" [25mm]

an extension ring is required.

See Cat. No. 6AER-.

Junction Box Accessories Ordering Information (Continued)

2 9/16"

[65mm]

8 7/16"

[214mm]

Catalog No./Item Description/Specification

142L-1 Two Level Junction Box –

Adaptable for either No. 2 Duct

or No. 4 Duct. No partitioning

required. Requires a 4" [102mm]

minimum pour. 3/8" [9.5mm]

upward adjustment of cover

plate is possible after proof. 5

3/4" [146mm] nominal diameter

round cover plate. 1/8" [3.2mm]

plate thickness. Use adjustable

extension ring when additional

height is needed. See Cat. No.

6AER-.

H14-AS Complete Access Activation

– For access to large number of

cables at activation. Requires

field cut 5" [127mm] hole in

duct. Can be used as an

afterset or preset on No. 4

Duct. For concrete pours over

1" [25mm] an extension ring is

required. See Cat. No. 6AER-.

8 1/2"

[216mm] 8 1/2"

[216mm]

[102mm]

Catalog No./Item Description/Specification

6AER-11/2 – 21/8 Adjustable Extension Ring-

6AER-23/8 – 3 For 142L-1, H338AU-1,

H14-AS, and 14H-1 Boxes.

Suffix refers to adjustable

height range. Select hardware

bag below to attach ring

to box.

AERHB-120 Hardware Bag - For

-128 adjustable extension ring. Suffix

-144 indicates depth of concrete

-152 over duct. Use chart below

-052 to determine hardware bag

required for 142L-1, H338AU-1,

H14-AS, and 14H-1 Boxes.

203UFD Blank Washer – For

closing unused junction

box No. 2 Duct opening.

Catalog No./Item Description/Specification

H14-BA Afterset Access Assembly

with Neoprene Boot – Used

with H14ABD to protect cables

coming out of duct.

H14BC Blanking Cap – Closes

5" [127mm] hole in duct.

H203 Blank Washer – For closing

unused junction box No. 4

Duct opening.

275SL (left-hand) Adapter – To reduce a

275SR (right-hand) No. 4 Duct opening in a

junction box to a No. 2

Duct opening. Specify

left or right hand.

276 Adapter – Used with 142L and

14H Junction Boxes. Reduces

No. 4 Duct opening to No. 2

Duct. Maintains 1" [25mm]

spacing between ducts. For

center opening in adapter

use Cat. No. 277.

1 9/16"

[40mm]

3 1/8"

[79mm]

(275SR Pictured)

1 9/16"

[40mm]

6 1/2"

[165mm]

1 1/2"

[38mm] 1 1/2"

[38mm]

6 7/16"

[164mm]

1 1/2"

[38mm]

Junction Box Accessories Ordering Information (Continued)

Hardware Bag Concrete Depth Over Duct

Cat. No. 1 1/2" 1 5/8" 1 3/4" 1 7/8" 2" 2 1/8" 2 3/8" - 3"

AERHB-120 X X

AERHB-128 X X

AERHB-144 X

AERHB-152 X

AERHB-052 X

NOTE: Use Cat. No. H202 Blank

Washer for 142L and 14H

Junction Boxes.

Catalog No./Item Description/Specifications

255-3/4 [19.1mm] Box Conduit Corner

-1 [25mm] Adapter – For one rigid or

-11/4 [32mm] PVC conduit. Suffix denotes

-11/2 [38mm] trade size.

-2 [51mm]

242-11/4 Male Adapter – For No. 2

Duct opening to two 1 1/4"

trade size conduits.

H232-2 Male Adapter – For No. 4

Duct opening to one 2"

trade size conduit.

Catalog No./Item Description/Specifications

212-3/4 Adapter – For No. 2 Duct

opening to one 3/4"

trade size conduit.

222-3/4 Adapter – For No. 2 Duct

opening to two 3/4"

trade size conduits.

232-1 Male Adapter – For No. 2

-11/4 Duct opening to one

-11/2 conduit. Suffix indicates

conduit trade size.

Junction Box Conduit Adapters Ordering Information

2 3/4"

[70mm]

3 1/8"

[79mm]

IMPORTANT!

The conduit adapters in this section will fit directly into the duct

openings in the junction boxes. All other conduit adapters require a field

cut piece of duct to transition from junction box opening to adapter.

1 1/4"

[32mm]

3 1/8"

[79mm]

3 1/8"

[79mm]

1 1/4"

[32mm]

3 1/8"

[79mm]

2 5/8"

[67mm]

[102mm]

2 1/4"

[57mm]

6 1/2"

[165mm]

3 3/4"

[95mm]

CONDUIT ADAPTER Inches [mm]

255-3/4, -1 1 7/8 [48]

255-1 1/4, -1 1/2 2 1/4 [57]

255-2 2 3/4 [70]

1414

Flanged round carpet/tile pans in brass or stainless steel

for 12JR boxes. Mount onto cover plate. Available in 1/4"

or 1/8" [6.4mm or 3.2mm] depths for carpet or tile floors.

4 3/4" [121mm] diameter (does not include flange). Flange

is 3/8" [9.5mm] wide.

CAT. NO. DESCRIPTION

SFCS5-1/8 Stainless 1/8"[6.4mm] deep x 5.561" O.D. [141mm]

SFCS5-1/4 Stainless 1/4" [3.2mm] deep x 5.561" O.D. [141mm]

SFCB5-1/8* Brass 1/8" [6.4mm] deep x 5.561" O.D. [141mm]

SFCB5-1/4* Brass 1/4" [3.2mm] deep x 5.561" O.D. [141mm]

ORDERING DATA

Flanged round carpet/tile pans in brass or stainless steel

for 12S, 14H, 142L, H338AU, 12FB or H14 Boxes. Mount

onto cover plate. Available in 1/4" or 1/8" [6.4mm or

3.2mm] depths for carpet or tile floors. 5 23/32" [144mm]

diameter (does not include flange). Flange is 3/8"

[9.5mm] wide.

CAT. NO. DESCRIPTION

6LHS-1/8 Stainless 1/8" [3.2mm] deep 6 39/64 [168mm] O.D.

6LHS-1/4 Stainless 1/4" [6.4mm] deep 6 39/64 [168mm] O.D.

6LHB-1/8 Brass 1/8" [3.2mm] deep 6 39/64 [168mm] O.D.

6LHB-1/4 Brass 1/4" [6.4mm] deep 6 39/64 [168mm] O.D.

ORDERING DATA

CAT. NO. DESCRIPTION

7LHS-1/8 Stainless 1/8" [3.2mm] deep 8 11/64 [208mm] O.D.

7LHS-1/4 Stainless 1/4" [6.4mm] deep 8 11/64 [208mm] O.D.

7LHB-1/8* Brass 1/8" [3.2mm] deep 8 11/64 [208mm] O.D.

7LHB-1/4* Brass 1/4" [6.4mm] deep 8 11/64 [208mm] O.D.

ORDERING DATA

Flanged round carpet/tile pans in brass or stainless steel

for 222FB Boxes. Mount onto cover plate. Available in 1/4"

or 1/8" [6.4mm or 3.2mm] depths for carpet or tile floors. 7

1/2" [191mm] diameter (does not include flange). Flange is

3/8" [9.5mm] wide.

CAT. NO. DESCRIPTION

10LHS-1/8 Stainless 1/8" [3.2mm] deep 11 15/64 [295mm] O.D.

10LHS-1/4 Stainless 1/4" [6.4mm] deep 11 15/64 [295mm] O.D.

10LHB-1/8* Brass 1/8" [3.2mm] deep 11 15/64 [295mm] O.D.

10LHB-1/4* Brass 1/4" [6.4mm] deep 11 15/64 [295mm] O.D.

ORDERING DATA

Flanged round carpet/tile pans in brass or stainless steel

for 14S, 222S, and 3222FB Boxes. Mount onto cover

plate. Available in 1/4" or 1/8" [6.4mm or 3.2mm] depths

for carpet or tile floors. 10 1/2" [267mm] diameter (does

not include flange). Flange is 3/8" [9.5mm] wide.

CAT. NO.

DESCRIPTION

14LHS-1/8 Stainless 1/8" [3.2mm] deep x 15.234" O.D. [387mm]

14LHS-1/4 Stainless 1/4" [6,4mm] deep x 15.234" O.D. [387mm]

14LHB-1/8* Brass 1/8" [3.2mm] deep x 15.234" O.D. [387mm]

14LHB-1/4* Brass 1/4" [6.4mm] deep x 15.234" O.D. [387mm]

ORDERING DATA

Flanged round carpet/tile pans in brass or stainless

steel for 224S and 3222S Boxes. Also fits 2-1JB2510

Walkercell Boxes and 18" [457mm] wide Junction Box

Headers. Mount onto cover plate.Available in 1/4" or 1/8"

[6.4mm or 3.2mm] depths for carpet or tile floors. 14 1/2"

[368mm] diameter (does not include flange). Flange is

3/8" [9.5mm] wide.

CAT. NO. DESCRIPTION

22LHS-1/8 Stainless 1/8" [3.2mm] deep x 23.234" O.D. [590mm]

22LHS-1/4 Stainless 1/4" [6.4mm] deep x 23.234" O.D. [590mm]

22LHB-1/8 Brass 1/8" [3.2mm] deep x 23.234" O.D. [590mm]

22LHB-1/4* Brass 1/4" [6.4mm] deep x 23.234" O.D. [590mm]

ORDERING DATA

Flanged round carpet/tile pans in brass or stainless steel

for 244S, 3224S, 3244S, 3424S and 3444S Boxes. Also

fits 33JB3510, 32JB3510, 22JB2510, 1 1/2 JB2510,

11JB2510, Walkercell Boxes and 24" [610mm] wide and

wider Junction Box Headers. Mount onto cover plate.

Available in 1/4" or 1/8" [6.4mm or 3.2mm] depths for

carpet or tile floors. 22" [559mm] diameter (does not

include flange). Flange is 3/8" [9.5mm] wide.

NOTE: Square Tile/Carpet Trims for heavy duty Junction Boxes

– need to increase depth of Pan by 1/8". Example: for

1/4" Carpet, use 3/8" deep Carpet Holder.

Walkerduct Flanged Round Carpet/Tile Holders Ordering Information

NOTE: Prior to completing installation, proper floor covering should be

installed in pan.

* Add suffix “-HD” for.090 thick material (.025 standard material

thickness) to accommodate high traffic and.or heavy loads.

Walkerduct Carpet/Tile Holders finish off your Walkerduct Infloor Systems. Just match the diameter of the

holder to the appropriate diameter of the Junction Box. Walkerduct Carpet/Tile Holders are available in a

variety of depths to accommodate the thickness of the carpet or tile floor covering.

You can also add some “WOW” to your power and communications infrastructure by specifying custom

engraved Walkerduct Junction Box Covers.

1515

Walkerduct Flanged Round Carpet/Tile Holders Ordering Information (Continued)

Flanged round carpet/tile pans in brass or stainless steel for

14JR and 222JR boxes. Mount onto cover plate. Available

in 1/4" or 1/8" [6.4mm or 3.2mm] depths for carpet or tile

floors. 8 7/8" [225mm] diameter (does not include flange).

Flange is 3/8" [9.5mm] wide.

CAT. NO. DESCRIPTION

SFCS9-1/8 Stainless 1/8" [6.4mm] deep x 9.686" O.D. [246mm]

SFCS9-1/4 Stainless 1/4" [3.2mm] deep x 9.686" O.D. [246mm]

SFCB9-1/8* Brass 1/8" [6.4mm] deep x 9.686" O.D. [246mm]

SFCB9-1/4* Brass 1/4" [3.2mm] deep x 9.686" O.D. [246mm]

ORDERING DATA

Flanged round carpet/tile pans in brass or stainless steel

for 224JR and 3222JR boxes. Mount onto cover plate.

Available in 1/4" or 1/8" [6.4mm or 3.2mm] depths for

carpet or tile floors. 13" [330mm] diameter (does not

include flange). Flange is 3/8" [9.5mm] wide.

CAT. NO. DESCRIPTION

SFCS14-1/8 Stainless 1/8" [6.4mm] deep x 13.812" O.D. [351mm]

SFCS14-1/4 Stainless 1/4" [3.2mm] deep x 13.812" O.D. [351mm]

SFCB14-1/8 Brass 1/8" [6.4mm] deep x 13.812" O.D. [351mm]

SFCB14-1/4* Brass 1/4" [3.2mm] deep x 13.812" O.D. [351mm]

ORDERING DATA

NOTE: Prior to completing installation, proper floor covering should be

installed in pan.

* Add suffix “-HD” for.090 thick material (.025 standard material

thickness) to accommodate high traffic and.or heavy loads.

CAT. NO. DESCRIPTION

SFCS17-1/8 Stainless 1/8" [6.4mm] deep x 17.187" O.D. [437mm]

SFCS17-1/4 Stainless 1/4" [3.2mm] deep x 17.187" O.D. [437mm]

SFCB17-1/8 Brass 1/8" [6.4mm] deep x 17.187" O.D. [437mm]

SFCB17-1/4* Brass 1/4" [3.2mm] deep x 17.187" O.D. [437mm]

ORDERING DATA

Flanged round carpet/tile pans in brass or stainless steel

for 244JR and 3224JR boxes. Mount onto cover plate.

Available in 1/4" or 1/8" [6.4mm or 3.2mm] depths for

carpet or tile floors. 16 3/8" [416mm] diameter (does not

include flange). Flange is 3/8" [9.5mm] wide.

CAT. NO. DESCRIPTION

SFCS20-1/8 Stainless 1/8" [6.4mm] deep x 17.936" O.D. [456mm]

SFCS20-1/4 Stainless 1/4" [3.2mm] deep x 17.936" O.D. [456mm]

SFCB20-1/8 Brass 1/8" [6.4mm] deep x 17.936" O.D. [456mm]

SFCB20-1/4 Brass 1/4" [3.2mm] deep x 17.936" O.D. [456mm]

ORDERING DATA

Flanged round carpet/tile pans in brass or stainless steel

for 3424JR and 3244JR boxes. Mount onto cover plate.

Available in 1/4" or 1/8" [6.4mm or 3.2mm] depths for

carpet or tile floors. 19 3/4" [502mm] diameter (does not

include flange). Flange is 3/8" [9.5mm] wide.

CAT. NO. DESCRIPTION

SFCS24-1/8 Stainless 1/8" [6.4mm] deep x 20.560" O.D. [522mm]

SFCS24-1/4 Stainless 1/4" [3.2mm] deep x 20.560" O.D. [522mm]

SFCB24-1/8 Brass 1/8" [6.4mm] deep x 20.560" O.D. [522mm]

SFCB24-1/4 Brass 1/4" [3.2mm] deep x 20.560" O.D. [522mm]

ORDERING DATA

Flanged round carpet/tile pans in brass or stainless steel for

3444JR boxes. Mount onto cover plate. Available in 1/4" or

1/8" [6.4mm or 3.2mm] depths for carpet or tile floors. 23

1/8" [587mm] diameter (does not include flange). Flange is

3/8" [9.5mm] wide.

NOTE: Square Tile/Carpet Trims for heavy duty Junction Boxes

– need to increase depth of Pan by 1/8". Example: for

1/4" Carpet, use 3/8" deep Carpet Holder.

Add some “Wow” to your power and

communications infrastructure.

Custom engraved Walkerduct® Junction Box Covers are available

in a wide range of metals, textures and finishes to enhance your

decor and increase recognition.

Each cover is custom-designed to your specifications. Your

Wiremold representative and our Technical Support team will walk

you through the process of designing and specifying your own

unique covers.

We’ll handle all the details and deliver them on time without the

premium cost. And because they’re from Wiremold, they’re the

perfect complement to your Infloor System.

Walkerduct Custom Junction Box Covers

Walkerduct Square Carpet/Tile Trim Ordering Information

Flanged square carpet/tile trim in

aluminum for Walkerduct JS Series

Boxes. Mount onto junction box.

Available in 1/4" or 1/8" [6.4mm

or 3.2mm] depths for carpet or tile

floors. Flange is 1/2 [12.7mm] wide.

Dimensions below do not include flange.

CAT. NO. DESCRIPTION JUNCTION BOX

CT6-1/8 6 13/16" x 6 13/16" x 1/8" [173mm x 173mm x 3.2mm] 12JS

CT6-1/4 6 13/16" x 6 13/16" x 1/4" [173mm x 173mm x 6.4mm] 12JS

CT10-1/8 10 15/16" x 11 15/16" x 1/8" [278mm x 278mm x 3.2mm] 14JS, 222JS

CT10-1/4 10 15/16" x 11 15/16" x 1/4" [278mm x 278mm x 6.4mm] 14JS, 222JS

CT15-1/8 15 1/16" x 15 1/16" x 1/8" [383mm x 383mm x 3.2mm] 224JS, 3222JS

CT15-1/4 15 1/16" x 15 1/16" x 1/4" [383mm x 383mm x 6.4mm] 224JS, 3222JS

CT18-1/8 18 7/16" x 18 7/16" x 1/8" [468mm x 468mm x 3.2mm] 244JS, 3224JS

CT18-1/4 18 7/16" x 18 7/16" x 1/4" [468mm x 468mm x 6.4mm] 244JS, 3224JS

CT21-1/8 21 13/16" x 21 13/16" x 1/8" [554mm x 554mm x 3.2mm] 3424JS, 3244JS

CT21-1/4 21 13/16" x 21 13/16" x 1/4" [554mm x 554mm x 6.4mm] 3424JS, 3244JS

CT25-1/8 25 3/16" x 25 3/16" x 1/8" [640mm x 640mm x 3.2mm] 3444JS

CT25-1/4 25 3/16" x 25 3/16" x 1/4" [640mm x 640mm x 6.4mm] 3444JS

ORDERING DATA

11/16"

[17.5mm]

1/2"

[12.7mm]

NOTE: 1/8" or 1/4" is depth of tile or carpet when used with JS

Boxes (1/4" thick cover plate). For HS Boxes, depth will be

reduced by 1/8" to accommodate the 3/8" thick cover plate.

Flangeless square carpet/tile trim in

aluminum for Walkerduct JS Series

Boxes. Mount onto junction box.

Available in 1/4" [6.4mm] or 1/8"

[3.2mm] depths for carpet or tile floors.

CAT. NO. DESCRIPTION JUNCTION BOX

FT6-1/8 6 13/16" x 6 13/16" x 1/8" [173mm x 173mm x 3.2mm] 12JS

FT6-1/4 6 13/16" x 6 13/16" x 1/4" [173mm x 173mm x 6.4mm] 12JS

FT10-1/8 10 15/16" x 11 15/16" x 1/8" [278mm x 278mm x 3.2mm] 14JS, 222JS

FT10-1/4 10 15/16" x 11 15/16" x 1/4" [278mm x 278mm x 6.4mm] 14JS, 222JS

FT15-1/8 15 1/16" x 15 1/16" x 1/8" [383mm x 383mm x 3.2mm] 224JS, 3222JS

FT15-1/4 15 1/16" x 15 1/16" x 1/4" [383mm x 383mm x 6.4mm] 224JS, 3222JS

FT18-1/8 18 7/16" x 18 7/16" x 1/8" [468mm x 468mm x 3.2mm] 244JS, 3224JS

FT18-1/4 18 7/16" x 18 7/16" x 1/4" [468mm x 468mm x 6.4mm] 244JS, 3224JS

FT21-1/8 21 13/16" x 21 13/16" x 1/8" [554mm x 554mm x 3.2mm] 3424JS, 3244JS

FT21-1/4 21 13/16" x 21 13/16" x 1/4" [554mm x 554mm x 6.4mm] 3424JS, 3244JS

FT25-1/8 25 3/16" x 25 3/16" x 1/8" [640mm x 640mm x 3.2mm] 3444JS

FT25-1/4 25 3/16" x 25 3/16" x 1/4" [640mm x 640mm x 6.4mm] 3444JS

ORDERING DATA

11/16"

[17.5mm]

1/8"

[3.2mm]

Catalog No./Item Description/Specifications

485

Coverplate Lifter –

Used to assist in removing cover

plates from junction boxes.

Catalog No./Item Description/Specifications

290C

Waterproof Sealing Compound –

Three tubes, 10.1 fluid ounces

each. Will seal approximately

100 couplings, 12 three-duct

boxes, 25 two-duct boxes, or

50 single-duct boxes.

H296

Sealing Tape –

180' roll of 2" tape used to seal

couplings and edges of junction

boxes.

Walkerduct Installation Products

NOTE: We highly recommend you use a stud finder, such as Milwaukee

Tool Sub-Scanner M12 Detection Tool, to find presets after the

concrete pour. This tool is able to locate presets through up to

6" of concrete and will simplify your installation.

Catalog No./Item Description/Specifications

1204BF

Communication Service Fitting –

Brass finish communication

fitting furnished with split bell

cap and grommet. No device

plate is included.

1204AL

Communication Service Fitting–

Aluminum finish communication

fitting furnished with split bell

cap and grommet. No device

plate is included.

1223BF Power Service Fitting

–

Brass

finish fitting includes housing,

bell cap, grommet, and single

U-slot, three-wire grounded,

20A, 125V receptacle.

Catalog No./Item Description/Specifications

1223AL

Power Service Fitting–

Aluminum fitting includes housing,

bell cap, grommet, and single

U-slot, three-wire grounded, 20A,

125V receptacle.

1230AL

Screw plug – Aluminum screw

plug to abandon service fitting.

Screws into housing.

1230BF

Screw plug – Brass screw

plug to abandon service fitting.

Screws into housing.

1200 Series Service Fittings Ordering Information

NOTE: Compatible with Walkerduct IPS duct.

Catalog No./Item Description/Specifications

500RT Faceplate –

Single opening. Ortronics

Series II and TracJack

adapters included.

500ACT Faceplate –

Single opening. Activate

CM-MABadapter included.

500B Faceplate – Blank.

500-MAAP Faceplate – Accepts Extron®

Electronics MAAP device plates.

500T Faceplate – 1" [25mm] I.D.

grommeted hole.

Catalog No./Item Description/Specifications

500SP- Faceplate – Single opening.

Suffix indicates hole diameter.

500DR Faceplate – For single

duplex receptacle.

500-GFI Faceplate – For Decora

or GFI device.

525HB Housing and Base

Plate –Only.

1/2 1/2" [12.7mm]

7/8 7/8" [22.2mm]

1.0625 1.0625" [27mm]

1 1/8 1 1/8" [29mm]

1.39 1.39" [35mm]

1 7/16 1 7/16" [37mm]

1 1/2 1 1/2" [38mm]

1 9/16 1 9/16" [40mm]

1 5/8 1 5/8" [41mm]

2 2" [51mm]

SUFFIX HOLE DIAMETER

2 5/8"

[67mm]

4 7/16"

[113mm]

NOTE: Compatible with Walkerduct IPS and Pro Series duct.

525 Series Service Fitting Ordering Information

Catalog No./Item Description/Specifications

825SFCK Conversion Kit – To attach

service fitting to 800 Series

floor boxes. Includes 825C

Ring, 1124L-1 Locking Nipple,

and 825P-1 Adapter.

430S505 Single Trim Plate – To attach

fitting to Walkerduct Pro

Series Preset. Base of 525

fitting not needed.

431D505 Double Trim Plate – To attach

two fittings to Walkerduct Pro

Series Presets. Base of 525

fitting not needed.

428B525 Flush Carpet Plate –

To attach to Walkerduct

Pro Series Plate.

Includes hardware.

Catalog No./Item Description/Specifications

436-2 -7/8 [22.2mm] Afterset Inserts for Duct –

-11/2 [38mm] 2" [51mm] IPS. 2 1/2" [64mm]

-2 [51mm] core drill size; 2 1/4" [57mm]

-23/8 [60mm] hole saw size. Suffix

-3 [76mm] denotes height.

424 -3/4 [19.1mm] Extensions – For 2" [51mm]

-1 [25mm] IPS preset or afterset inserts.

Suffix denotes height

of extension.

1126A-1/4 [6.4mm] Adapter – To change 2" [51mm]

-3/4 [19.1mm] IPS preset or afterset to

-1 [25mm] reduced opening size.

-11/4 [32mm] Suffix denotes opening size.

-11/2 [38mm]

1124 -1

[25mm]

Locking Nipple –

For 1" [25mm]

IPS opening; 1" [25mm] long.

1124L -1

[25mm]

Locking Nipple –

For 1" [38mm]

IPS opening; 1 1/2" [38mm] long.

1124 -11/4

[38mm]

Locking Nipple –

For 1 1/4"

[32mm] IPS opening;

1" [25mm] long.

1124L -11/4 [38mm]

Locking Nipple –

For 1 1/4"

[32mm] IPS opening;

1 1/2" [38mm] long.

1124F -1

[25mm]

Locking Nipple –

For 1" [25mm]

IPS opening; 5/8" [16mm] long.

For use on Flushduct

Infloor Raceway.

455F-1 Outlet Flange – For 1 5/8"

[241mm] diameter opening

on Flushduct Infloor

Raceway. Accepts 1"

[25mm] locking nipple.

Blanking Plates –

3 1/2" [89mm] diameter top plate

525 Series Service Fitting Ordering Information (continued)

OLD CATALOG NUMBER NEW CATALOG NUMBER

505A, 501E 525A

505ACT 525ACT

505B, 502E 525B

505C, 503E 525C

505F 525F

505G 525G

505H, 523E 525H

505HB 525HB

505I 525I

505J 525J

505RT 525RT

Cross Reference

1044B For 3/4" IPS

1044S

1045B For 1" IPS

1045S

1046B For 1 1/4" IPS

1046S

1043B For 2" IPS

1043S

NOTE: B - Brass

S - Stainless Steel

NOTE: Compatible with Walkerduct IPS and Pro Series duct.

Catalog No./Item Description/Speciﬁcations

1124-1 Locking Nipple – For 1" [25mm] IPS

insert opening. 1" [25mm] long.

1124L-1 Locking Nipple – For 1" [25mm] IPS

insert opening. 1 1/2" [38mm] long.

1124F-1 Locking Nipple – For 1" [25mm] IPS

opening. 5/8" [15.9mm] long. For use

on Flushduct Infloor Raceway.

Catalog No./Item Description/Speciﬁcations

1126A -1/4 [6.4mm] Adapter – To change 2" [51mm]

-3/4 [19mm] IPS preset to 1" [25mm].

-1 [25mm] Suffix denotes opening size.

-1 1/2 [38mm]

455F-1 Outlet Flange – For 1 5/8" [41mm]

diameter opening. For use on

Flushduct Infloor Raceway.

Activation Accessories Ordering Information

It is easy to design a unique Multiplex Service Fitting. Just follow these steps:

1. Determine what fitting will be mounted to (ie: Walkerduct Underfloor Duct, etc).

2. Determine size required based on single or dual service needed. For 8-Plex, select appropriate base style.

3. Select the required number of power, communication, A/V, or blank faceplates. Select two for 4-Plex and four for 8-Plex.

4. Select installation accessories.

That’s all! It’s so easy!

Multiplex Selection and Ordering

Multiplex Series Service Fitting Ordering Information

Catalog No./Item Description/Speciﬁcations

MP4 Single service fitting includes housing, base, two mounting frames, and

mounting hardware. For use on 2" [51mm] IPS underfloor duct systems.

Can also be installed on single preset in Walkerduct Pro Series System.

Has 1/2" and 3/4" trade size concentric conduit knockouts on each end.

Overall capacity is 55.3 cu. in. [906 cu cm]. Fitting also provides 1" and 1

1/4" trade size concentric knockouts in baseplate.

MP8 Dual service fitting includes housing, base, two mounting frames, divider,

and mounting hardware. For use on two No. 2 ducts or one No. 2 and one

No. 4 duct. On Walkerduct Pro Series the fitting can be installed on any

two-duct system. Has 1/2" and 3/4" trade size concentric conduit

knockouts on each end. Overall capacity is 104.3 cu. in. [1709 cu cm].

Fitting also provides 1" and 1 1/4" trade size concentric knockouts

and one 1" trade size knockout in baseplate.

MP8-1 Same as MP8, except mounts on PK and N-R-G Presets, one No. 2 , or

one No. 4 duct. On Walkerduct Pro Series the fitting can be installed on

any two-duct system. Overall capacity is 104.3 cu. in. [1709 cu cm]. Has

1/2" and 3/4" trade size concentric knockouts on each end. Fitting also

provides one 1" trade size knockout in baseplate.

4-Plex Single and 8-Plex Dual Service Fittings Ordering Information

[76mm]

6 3/4"

[171mm] 4 3/4"

[121mm]

[76mm]

6 3/4"

[171mm]

8 3/4"

[222mm]

[76mm]

6 3/4"

[171mm]

8 3/4"

[222mm]

NOTE: Compatible with Walkerduct IPS and Pro Series duct.

Catalog No./Item Description/Speciﬁcations

LTF48-1 Faceplate – 1" [25mm]

diameter bushed opening.

LTF48-2 Faceplate – 2" [51mm]

diameter bushed opening.

LTF48-MAAP** Faceplate – Accepts four (4)

Extron® Electronics MAAP device

plates.

Catalog No./Item Description/Speciﬁcations

LTF48-RT Faceplate –

Single opening

• Accepts Ortronics

MAB6TJ TracJack

and MAB3S2

Series II adapters.

LTF48-ACT Faceplate –

Single opening.

• Accepts the Activate

CM-MAB adapter.

LTF48-B Faceplate – Blank.

Communication Faceplates for Multiplex Service Fittings Ordering Information*

* All plates include mounting hardware. Plate dimensions are 3.365"

[85.5mm] wide, x 2.98" [75.7mm] high, excluding flanges.

** Products are ETL Listed.

Catalog No./Item Description/Speciﬁcations

M-2GFI Power Faceplate –

Dual GFI opening.

M-DR/GFI Power Faceplate – Single duplex

and GFI openings.

Catalog No./Item Description/Speciﬁcations

M-DR Power Faceplate –

Single duplex opening.

M-2DR Power Faceplate –

Dual duplex opening.

M-GFI Power Faceplate –

Single GFI opening.

Power Faceplates for Multiplex Service Fittings Ordering Information*

* All plates include mounting hardware. Plate dimensions are 3.365"

[85.5mm] wide, x 2.98" [75.7mm] high, excluding flanges.

Multiplex Series Service Fitting Ordering Information

NOTE: Compatible with Walkerduct IPS and Pro Series duct.

Pro Series Service Fitting Ordering Information

Catalog No./Item Description/Specifications

817PCC-BLK One-Gang Nonmetallic Carpet

817PCC-BRN and Tile Flange – Available in

black or brown. Accepts Ortronics

MAB6TJ TracJack and MAB3S2

Series II bezels, Activate CM-MAB

bezel, and Wiremold Open System

inserts, all sold separately.

827PCC-BLK Two-Gang Nonmetallic Carpet

827PCC-BRN and Tile Flange – Available in

black or brown. Accepts Ortronics

MAB6TJ TracJack and MAB3S2

Series II bezels, Activate CM-MAB

bezel, and Wiremold open inserts,

all sold separately.

837PCC-BLK Three-Gang Nonmetallic Carpet

837PCC-BRN and Tile Flange – Available in

black or brown. Accepts Ortronics

MAB6TJ TracJack and MAB3S2

Series II bezels, Activate CM-MAB

bezel, and Wiremold Open System

inserts, all sold separately.

5 3/4"

[146mm]

4 3/4"

[121mm]

5 3/4"

[146mm]

8 7/8"

[225mm]

5 3/4"

[146mm]

13"

[330mm]

Catalog No./Item Description/Specifications

817B One-Gang Brass or Brushed

818TCAL Aluminum Combination Carpet

and Tile Flange – Accepts

Ortronics MAB6TJ TracJack and

MAB3S2 Series II bezels, Activate

CM-MAB bezel, and Wiremold

Open System inserts, all sold

separately.

827B Two-Gang Brass or Brushed

828TCAL Aluminum Combination Carpet

and Tile Flange – Accepts

Ortronics MAB6TJ TracJack and

MAB3S2 Series II bezels, Activate

CM-MAB bezel, and Wiremold

Open System inserts, all sold

separately.

837B Three-Gang Brass or Brushed

838TCAL Aluminum Combination Carpet

and Tile Flange – Accepts

Ortronics MAB6TJ TracJack

and MAB3S2 Series II bezels,

Activate CM-MAB bezel, and

Wiremold Open Systems inserts,

all sold separately.

Walkerduct Pro Series Flush Flanges Ordering Information

A B

FLANGE Inches [mm] Inches [mm]

817TCAL 5.940 [150.9] 4.920 [125.0]

817B 6.080 [154.4] 5.060 [128.5]

A B

FLANGE Inches [mm] Inches [mm]

827TCAL 5.940 [150.9] 9.045 [239.7]

827B 6.080 [154.4] 9.185 [233.3]

NOTE: Brass covers and flanges ARE NOT interchangeable with

aluminum or nonmetallic covers and flanges.

Nonmetallic covers ARE interchangeable with aluminum flanges.

NOTE: Brushed aluminum flanges come with beveled edges.

A B

FLANGE Inches [mm] Inches [mm]

837TCAL 5.940 [150.9] 13.170 [334.5]

837B 6.080 [154.4] 13.310 [338.1]

NOTE: Brushed aluminum flanges come with beveled edges.

NOTE: Compatible with Walkerduct Pro Series duct.

Catalog No./Item Description/Specifications

828R Brass or Brushed Aluminum

828R-TCAL Duplex Cover Plate – Flip lids.

Can also be used with a 106

type communication bezel.

828GFITC Brass or Brushed Aluminum

828GFITCAL GFI Cover Plate –

May be used

with Activate and Ortronics

Connectivity Systems in

conjunction with 817, 827

and 837 Series flanges.

828DPGFITC Brass or Brushed Aluminum

828DPGFITCAL Rectangular Cover Plate –

Allows

for mounting of a duplex style

receptacle with a rectangular flip lid

cover plate.

828SPTC Brass Duplex Cover Plate –

Screw plugs. Screw plugs are

1 1/2" [38mm] in diameter.

829STC Brass Communication Cover

Plate – Data slides. Feed through

only, not for use with a mounting

plate for communication jacks.

Catalog No./Item Description/Specifications

829CK Brass or Brushed Aluminum

830CKTCAL Communication Cover Plate –

2 5/8" and 2 1/4" [67mm and

57mm] plugs.

829CK-1 Brass or Brushed Aluminum

830CKTCAL-1 Communication Cover Plate –

2 5/8" and 1" [67mm and

25mm] plugs.

829CK-3/4 Brass or Brushed Aluminum

830CKTCAL-3/4 Communication Cover Plate –

2 5/8" and 3/4" [67mm and

19.1mm] plugs.

829CK-1/2 Brass or Brushed Aluminum

830CKTCAL-1/2 Communication Cover Plate –

2 5/8" and 1/2" [67mm and

12.7mm] plugs.

Walkerduct Pro Series Flush Covers Ordering Information

NOTE: Brass covers and flanges ARE NOT interchangeable with aluminum

or nonmetallic covers and flanges.

Nonmetallic covers ARE interchangeable with aluminum flanges

A B

COVER Inches [mm] Inches [mm]

830CKTCAL 3.290 [83.6] 4.310 [109.5]

829CK 3.156 [80.2] 4.182 [106.2]

A B

COVER Inches [mm] Inches [mm]

830CKTCAL-1 3.290 [83.6] 4.310 [109.5]

829CK-1 3.156 [80.2] 4.182 [106.2]

A B

COVER Inches [mm] Inches [mm]

830CKTCAL-3/4 3.290 [83.6] 4.310 [109.5]

829CK-3/4 3.156 [80.2] 4.182 [106.2]

A B

COVER Inches [mm] Inches [mm]

830CKTCAL-1/2 3.290 [83.6] 4.310 [109.5]

829CK-1/2 3.156 [80.2] 4.182 [106.2]

A B

COVER Inches [mm] Inches [mm]

828R-TCAL 3.290 [83.6] 4.310 [109.5]

828R 3.156 [80.2] 4.182 [106.2]

A B

COVER Inches [mm] Inches [mm]

828GFITCAL 3.290 [83.6] 4.310 [109.5]

828GFITC 3.156 [80.2] 4.182 [106.2]

NOTE: Not available in Brushed Aluminum finish.

3 1/8"

[79mm]

4 1/8"

[105mm]

3 1/8

[79mm]

4 1/8

[105mm]

3.156"

[80.2mm]

4.182"

[106.2mm]

Pro Series Service Fitting Ordering Information (continued)

NOTE: Compatible with Walkerduct Pro Series duct.

Catalog No./Item Description/Specifications

828PR-BLK Nonmetallic Duplex Cover Plate –

828PR-BRN

Flip lids. Available in black or brown.

Can also be used with a 106 type

communication bezel.

828PRGFI-BLK Nonmetallic GFI Cover Plate –

828PRGFI-BRN Available in black or brown. May

be used with Activate and

Ortronics Connectivity systems in

conjunction with 817, 827 and

837PCC Series flanges.

829PFL-BLK* Nonmetallic Communication

829PFL-BRN* Cover Plate – Individual flip

lids. Available in black or brown.

Gasket included.

Accepts Activate

CM-MAB bezel, and Wiremold Open

System inserts, all sold separately.

Catalog No./Item Description/Specification

829PFLRT-BLK

Nonmetallic Communication

829PFLRT-BRN* Cover Plate – Individual flip

lids. Available in black or brown.

Gasket included. Accepts Ortronics

MAB6TJ TracJack and MAB3S2

Series II bezels included.

829PCK-BLK Nonmetallic Communication

829PCK-BRN Cover Plate – Breakouts.

Available in black or brown. Feed

through only, not for use with a

mounting plate for communication

jacks.

829PSTC-BLK Nonmetallic Communication

829PSTC-BRN Cover Plate – Data slides.

Available in black or brown. Feed

through only, not for use with a

mounting plate for communication

jacks.

Walkerduct Pro Series Flush Covers Ordering Information (continued)

3 3/16"

[81mm]

4 1/8"

[105mm]

3 3/16"

[81mm]

4 1/8"

[105mm]

3 3/16"

[81mm]

4 1/8"

[105mm]

* Replacement flip lids can be ordered under Cat. No. PFL-BLK and PFL-BRN. Each Cat. No. comes with three flip lids. The above cover plates are listed for

tile and carpet applications.

3 3/16"

[81mm]

4 1/8"

[105mm]

3 3/16"

[81mm]

4 1/8"

[105mm]

3 3/16"

[81mm]

4 1/8"

[105mm]

NOTE: Brass covers and flanges ARE NOT interchangeable with aluminum or nonmetallic covers and flanges.

Nonmetallic covers ARE interchangeable with aluminum flanges

Pro Series Service Fitting Ordering Information (continued)

NOTE: Compatible with Walkerduct Pro Series duct.

Catalog No./Item Description/Specifications

428DR Flush Carpet Plate – Single or double duplex

428DR2 opening. Flush plate is 3 7/8" x 4 5/8" [98mm x 117mm].

428B075 Flush Carpet Plate – Opening fits 3/4" trade size conduit or liquidtite.

Includes spacer for liquidtite connection. Flush plate is 3 7/8" x 4 5/8"

[98mm x 117mm].

428BL Flush Carpet Plate – Blank plate for abandoning preset or can be field

punched for custom sized opening. Flush plate is 3 7/8" x 4 5/8"

[98mm x 117mm].

428B525 Flush Carpet Plate – To attach 525 Series Service Fitting. Center hole

diameter is 1 5/8" [41mm]. Flush plate is 3 7/8" x 4 5/8" [98mm x 117mm].

433DR Flush Carpet Plate – Single or double duplex opening with finishing plate.

433DR2 Oversized plate covers flush plate and carpet edges. Finishing plate is

4 3/4" x 5 3/8" [121mm x 137mm]. Flush plate is 3 7/8" x 4 5/8"

[98mm x 117mm].

Walkerduct Pro Series Flush Carpet Plates

For those applications where a basic connection is needed out

of the preset, steel carpet plates are available. Made of 14 ga.

galvanized steel, these plates provide a sturdy activation for

conduit or receptacle connections. The plate dimensions are 3 7/8"

wide x 4 5/8" long [98mm x 117mm]. Hardware for attaching to

preset is included with plates. Screws provide 1 11/16" [43mm]

upward adjustment.

Steel carpet plates provide a sturdy activation for conduit or

receptacle connections.

– IMPORTANT! –

Flush carpet plates are to be used only within

a protected, enclosed environment such as

under a retail counter on carpeted floors.

– IMPORTANT –

A minimum 1 1/2" preset or afterset is required on Pro Series

underfloor duct to support standard duplex receptacles and

communication devices when using flush activations. The 1"

preset or afterset should be specified for pedestal style fittings

or when cabling will be pulled through the activation point.

Walkerduct Pro Series Flush Carpet Plates Ordering Information

– IMPORTANT –

A minimum 1 1/2" preset or afterset is required on Pro Series

underfloor duct to support standard duplex receptacles and

communication devices when using flush activations. The 1"

preset or afterset should be specified for pedestal style fittings

or when cabling will be pulled through the activation point.

Pro Series Service Fitting Ordering Information (continued)

NOTE: Compatible with Walkerduct Pro Series duct.

Walkerduct Pro Series Trim Plates

Available in brass or brushed aluminum, blanking plates can be used

to cover an abandoned preset opening. They can also be used under

a 525 Series Service Fitting or a conduit connector. Hardware to attach

plate to preset is included.

Catalog No./Item Description/Specification

430AL Single Blanking Plate –

430BR In brass or aluminum.

Dimensions are 5 1/16"

x 6 1/16" [129mm x 154mm].

431AL Double Blanking Plate –

431BR In brass or aluminum.

Dimensions are 9 3/16"

x 6 1/16" [233mm x 154mm].

432AL Triple Blanking Plate –

432BR In brass or aluminum.

Dimensions are 13 5/16"

x 6 1/16" [338mm x 154mm].

430AL075 Single Conduit Trim Plate –

430BR075 In brass or aluminum.

Opening for 3/4" trade size

conduit or liquidtite.

Dimensions are 5 1/16"

x 6 1/16" [129mm x 154mm].

Catalog No./Item Description/Specification

431AL075 Double Conduit Trim Plate –

431BR075 In brass or aluminum. Two

openings for 3/4" trade size

conduit or liquidtite.

Dimensions are 9 3/16"

x 6 1/16" [233mm x 154mm].

432AL075 Triple Conduit Trim Plate –

432BR075 In brass or aluminum. Three

openings for 3/4" trade size

conduit or liquidtite.

Dimensions are 9 3/16"

x 6 1/16" [233mm x 154mm].

430S505 Single 525 Trim Plate – To

attach 525 Series Service Fitting

on top of preset. Aluminum finish

only. Dimensions are 5 1/16" x

6 1/16" [129mm x 154mm]. Fits

all 525 Series Service Fittings.

431D505 Double 525 Trim Plate –

To attach two 525 Series

Service Fittings on top of

preset. Aluminum finish only.

Dimensions are 9 3/16" x

6 1/16" [233mm x 154mm]. Fits

all 525 Series Service Fittings.

Catalog No./Item Description/Specifications

427 Fiber Loop Kit – Nonmetallic clips snap into tabs

in preset base. Holds up to one meter of fiber optic

or UTP cable. Maintains 1 1/4" [32mm] bend radius.

Walkerduct Pro Series Activations Ordering Information

NOTE: See ED1225 for ordering information on 525 Series Service Fittings.

Source I® and Source II® Service Fittings ARE NOT compatible with Walkerduct Pro Series Presets. Source I can be used as an afterset only. 817B,

817PCC and 817TCAL Series cannot be installed on Walkerduct Source II® Systems.

Walkerduct Pro Series Trim Plates Ordering Information

Pro Series Service Fitting Ordering Information (continued)

NOTE: Compatible with Walkerduct Pro Series duct.

Catalog No./Item Description/Specifications

PSRC9TCGY Quad Power- Available in gray (GY), aluminum (AL), black (BK) or brass (BS). Quad 15A

PSRC9TCAL receptacle included for standard or isolated ground wiring. Unit complete with link straps,

PSRC9TCBK adapter plate and receptacle bracket to attach preset or afterset.

PSRC9TCBS

PSRC9TC Series Power Fittings Ordering Information

Catalog No./Item Description/Specifications

PSRC9AMDTCGY Quad Communication –

PSRC9AMDTCAL Available in gray, aluminum, black or brass. Unit complete with link straps and adapter plate

PSRC9AMDTCBK to attach preset or afterset. Includes two (2) Ortronics® TrackJack adapters, two (2) Ortronics®

PSRC9AMDTCBS Series II adapters and Wiremold Open System adapters. Modular jacks sold separately.

PSRC9AMDTC Series All Communication Fittings Ordering Information

Catalog No./Item Description/Specifications

PSRC9FFTCGY Flush Furniture Feed – Available in gray, aluminum, black or brass. Unit complete with link

PSRC9FFTCAL straps, adapter plate, and conduit assembly featuring (1) 3/4" trade size and (2) 1/2" trade size

PSRC9FFTCBK conduit connections and closure plugs.

PSRC9FFTCBS

PSRC9FF2TCGY 2" [51mm] Flush Furniture Feed – Available in gray, aluminum, or black. Unit complete

PSRC9FF2TCAL with link straps, adapter plate, and features concentric screw plugs that allow for 11/4" or

PSRC9FF2TCBK 2" trade size conduit fitting connections.

PSRC9 Series Furniture Feed Fittings Ordering Information

PSRC9 Series Service Fitting Ordering Information

NOTE: Compatible with Walkerduct Pro Series duct.

Catalog No./Item Description/Specifications

4210 1" [25mm] High Afterset

4215 1 1/2" [38mm] High Afterset

4220 2" [51mm] High Afterset

4225 2 1/2" [64mm] High Afterset

4230 3" [76mm] High Afterset – Installed either before or after concrete pour to create activation

from duct. Requires 6 1/2" [165mm] core drilled hole in concrete and 2 1/2" [64mm] diameter hole

in duct. Grout fill required around afterset once installed to fill voids and support fitting flange.

Attaches to duct using locking tabs. Extensions can be attached to increase height (see below).

Aftersets are gangable and include alignment clip and mudcap.

425 1/2" (12mm) High Extension

426 1" (25mm) High Extension – Used to increase height of preset or afterset. Die cast construction.

Attach to preset or afterset with push on metal sleeves (included). Cat. No. 426 can be stacked,

Cat. No. 425 cannot be stacked.

421 Mudcap – Steel replacement cap for preset. Recessed to hold 3/8" [9.5mm] concrete.

PSRC9 Series Activation Accessories Ordering Information

IMPORTANT!

PSRC9 Series power and communication styles can be applied to Walkerduct

Pro Series presets and aftersets 2" [51mm] and above. The PSRC9 furniture

feed style can be applied to Pro Series presets and aftersets 1" and above.

PSRC9 Series Service Fitting Ordering Information (continued)

NOTE: Compatible with Walkerduct Pro Series duct.

Catalog No./Item Description/Specifications

S125B Cover Plate – Flush brass

power cover plate only (flip lid)

with four mounting screws

S125BLK Cover Plate –

S125BRN Nonmetallic double duplex

membrane cover plate.

Available in black (SL125BLK)

or brown (S125BRN).

S130BLK Cover Plate – Nonmetallic

S130BRN double duplex membrane

cover plate. Available in

black (S130BLK) or brown

S130BRN)

829PSTC-BLK Cover Plate – Flush

829PSTC-BRN polycarbonate communication

cover plate with slides and

four mounting screws. Black

(829PSTC-BLK) or brown

(829PSTC-BRN).

829STC Cover Plate – Flush brass

communication cover plate

with slides and four

mounting screws.

829CK

Cover Plate –

Flush brass

communication cover plate

(2 5/8" and 2 1/4" diameter

trade size screw plugs) with

four mounting screws.

829CK-3/4

Cover Plate –

Flush brass

communication cover plate

(2 5/8" and 3/4" diameter trade

size screw plugs) with four

mounting screws.

829CK-1/2

Cover Plate –

Flush brass

communication cover plate

(2 5/8" and 1/2" diameter trade

size screw plugs) with four

mounting screws.

Catalog No./Item Description/Specifications

S175BLK Double Duplex Power

S175BRN Activation – Double duplex

activation available in black

(S175BLK) or brown (S175BRN)

polycarbonate assembly, 7/8"

to 3 3/8" [22.2mm to 86mm]

concrete topping. 15A, 125V

receptacles included.

S165BLK Complete Flush Activation

–

S165BRN Flush polycarbonate power –

single duplex black (S165BLK)

or brown (S165BRN). 15A,

125V receptacles included.

S165B Complete Flush Activation

–

Flush brass power – single

duplex flip lids. May be used

with 106 type adapters for

data applications.

S166BLK Complete Flush Activation

–

S166BRN Flush polycarbonate

communication slides available

in black (S166BLK) or brown

(S166BRN.

S166B Complete Flush Activation

–

Flush brass communication

(slides). Used for data cable

pass-through.

S124BLK Carpet Flange – Flush

S124BRN polycarbonate carpet flange

only with mounting screws.

Available in black (S124BLK)

or brown (S124BRN).

S124B Carpet Flange – Flush brass

carpet flange only with

mounting screws.

5 3/4"

[146mm]

5/16" [7.9mm]

Flange Thickness

4 3/4"

[121mm]

1/4" [6.4mm]

Flange Thickness

5 3/4"

[146mm]

4 3/4"

[121mm]

Source I Series Flush Activations Ordering Information

1/4" [6.4mm]

Flange Thickness

5 3/4"

[146mm] 4 3/4"

[121mm]

1/4" [6.4mm]

Flange Thickness

5 3/4"

[146mm] 4 3/4"

[121mm]

5/16" [7.9mm]

Flange Thickness

5 3/4"

[146mm] 4 3/4"

[121mm]

1/4" [6.4mm]

Flange Thickness

4 3/4"

[121mm]

5 3/4"

[146mm]

5/16" [7.9mm]

Flange Thickness

4 3/4"

[121mm]

5 3/4"

[146mm]

3 1/8"

[80mm]

4 1/8"

[106mm]

3 1/8"

[80mm]

4 1/8"

[106mm]

3 3/16"

[81mm]

4 1/8"

[105mm]

3 1/8"

[80mm]

4 1/8"

[105mm]

3 1/8"

[80mm]

4 1/8"

[106mm]

3 1/8"

[80mm]

4 1/8"

[105mm]

4 1/8"

[105mm] 3 3/16"

[81mm]

4 1/8"

[105mm]

3 3/16"

[81mm]

NOTE: Compatible with Walkerduct Pro Series duct.

4" [102mm]

Diameter

Catalog No./Item Description/Specifications

439 Attaching Ring – For

polycarbonate afterset use

only. No adjusting ring

required. 4" [102mm] O.D.

Four #6-32 hold-down screws

provided.

897AR Adjusting Ring – Adjusting

ring (with three adjusting

screws) for use with 437

Attaching Rings – power for

brass fitting only. 3 25/32"

[96mm] O.D.

898AR Adjusting Ring – Adjusting ring

(with three adjusting screws)

for use with 437 Attaching

Rings – communication only

(brass and polycarbonate

fittings) and power for

polycarbonate fitting only.

3 25/32" [96mm] O.D.

S1ER Attaching Ring Extension –

Extension ring – mounts

on top of 437 Attaching Ring.

Includes extension ring and

three mounting screws. 4"

[102mm] O.D. Add suffix to

indicate ring height: 7/8", 1 1/8",

1 1/2", 2", 2 3/8", 3 1/8".

We recommend using a shallow

Attaching Ring and deep

extension ring whenever

possible.

3 1/8"

[80mm]

4 1/8"

[105mm]

3 1/8"

[80mm]

4 1/8"

[106mm]

Source I Series Flush Activations Ordering Information (continued)

4" [102mm] Diameter

4" [102mm]

Diameter

7/8

[22.2mm]

1/2"

[12.7mm]

4" [102mm] Diameter

3 3/4" [95mm] Diameter

3/4"

[19.1mm]

3 3/4" [95mm] Diameter

3/4"

[19.1mm]

S1MC Mudcap

437 Attaching Ring

No. 2 Duct

Carpet Flange S124BLK/BRN

439 Attaching Ring

Duplex Plate with

Membrane S130BLK/BRN

439 Afterset Insert & Polycarbonate Source I Fitting

437 Preset Insert Installation Guidelines

NOTE: 437 Attaching ring can be used

as a preset or afterset.

Drill 2 1/2" [64mm] hole in duct

where activation is desired. Install

attaching ring in hole in raceway

before concrete is poured. Attaching

ring is secured by tightening

locking tabs. Be sure the locking

tabs are oriented lengthwise with

the raceway. The mudcap should

be securely in place before the

concrete pour. After the pour, chip

away concrete and remove mudcap.

Attach 437 Ring, 897/898AR Ring

and Service Fitting (not shown).

NOTE: Compatible with Walkerduct Pro Series duct.

NOTES

ED830R13 – Updated September 2015 – For latest specs visit www.legrand.us/wiremold

Electrical Wiring Systems

60 Woodlawn Street

West Hartford, CT 06110

Phone: 1.877.BY.LEGRAND (295-3472)

www.legrand.us

570 Applewood Crescent

Vaughan, Ontario L4K 4B4

Phone:905.738.9195

www.legrand.ca

NOTES

Brochure

1000300948-Brochure 1000300948-Brochure 1000300948-Brochure B5 unilog cesco-content

1000450869-Brochure 1000450869-Brochure 1000450869-Brochure B5 unilog cesco-content

1000507152-Catalog 1000507152-Catalog 1000507152-Catalog B5 unilog cesco-content

1000217405-Attachment 1000217405-Attachment 1000217405-Attachment B5 unilog cesco-content

Navigation menu

Versions of this User Manual:

Views

Navigation