340872_Titan IS Eng Installation Directions

: Pdf 1000273306-Installationsheet 1000273306-InstallationSheet B5 unilog

Open the PDF directly: View PDF .
Page Count: 4

TITAN™INSTALLATION INSTRUCTIONS

INCANDESCENT DIMMERS, MAGNETIC LOW VOLTAGE DIMMERS,

FAN SPEED CONTROLS, DEHUMMER FAN SPEED CONTROLS,

FLUORESCENT DIMMERS P/N 340872

INCANDESCENT DIMMERS “CD” SERIES: These dimmers are for use with

Incandescent and Halogen lamps.

CAUTION: To reduce the risk of overheating and possible damage to other

equipment, do not install to control a receptacle, a fluorescent light, a motor-

operated appliance, or a transformer supplied appliance.

• Do not use this dimmer with incandescent lamps whose power require-

ments exceed maximum power (stated in Watts) of this control.

• Do not connect this dimmer to power source other than 120VAC, 60 Hz only.

• Use copper wire only.

MAGNETIC LOW VOLTAGE DIMMERS “CDLV” SERIES: These dimmers are for

use with Magnetic Low Voltage Incandescent and Halogen lamps.

CAUTION: To reduce the risk of overheating and possible damage to other

equipment, do not install to control a receptacle, a fluorescent light, or a

motor-operated appliance. Connect only in a 120VAC, 60 Hz circuit to control

the primary winding of a transformer supplied incandescent and halogen

lamp. The maximum VA rating of this dimmer applies to the transformer

input, not the load on the transformer secondary.

• Do not use to control a solid state electronic low voltage transformer.

• Do not use with inoperative or missing lamps. Use of this dimmer with

inoperative or missing lamps can create an over current condition which

may damage the transformer. Use transformers that incorporate thermal

protection or a fuse at the primary windings.

• Use copper wire only.

FAN SPEED CONTROLS “CDSC” SERIES: These controls are for use with

ceiling paddle fans with split-capacitor or shaded pole motors only. Use only

with ceiling paddle fans that are marked “Suitable for Use with Solid State

Fan Speed Controls.” Set multi-speed fans to their highest setting before

installing this control.

• Multiple ceiling paddle fans of the same type may be used if the maximum

power (stated in Amps) of this control is not exceeded.

• Do not connect this control to power source other than 120VAC, 60 Hz only.

• Use copper wire only.

• This control is intended for installation in either a metal outlet box or a

polymeric (plastic) outlet box.

DEHUMMER FAN SPEED CONTROLS “CDDH” SERIES: These controls are for

use with a single ceiling paddle fan only.

• Do not use this control with a ceiling paddle fan that exceeds the maximum

power (stated in Amps) of this control.

• Do not connect this control to power source other than 120VAC, 60 Hz only.

• Use copper wire only.

FLUORESCENT DIMMERS “CDFB” SERIES: These dimmers are for use with

electronic dimming ballasts that utilize 2-wire control (see TABLE 1 below):

• Use copper wire only.

FLUORESCENT DIMMERS “CD3FB” SERIES: These dimmers are for use with

electronic dimming ballasts that utilize 3-wire control (see TABLE 2 below):

• Use with Lutron FDB or ECO series Electronic Fluorescent Dimming

Ballasts only. Do not use with any other ballasts.

• Use copper wire only.

PACKAGE CONTENTS

One of the following Dimmers:

Narrow Dimmers Wide Dimmers

Cat no.: Cat no.: Cat no.: Cat no.:

CD700 CD703P CD1600 CD1603P

CD1100 CD1103P CD2000 CD2003P

CDLV700 CDLV703P CDLV1600 CDLV1603P

CDLV1100 CDLV1103P CDFB10 CDFB103P

CDFB5 CDFB53P CDFB16 CDFB163P

CDFB8 CDFB83P CDFB7-277 CDFB73P-277

CDSC6 CD3FB163P CDFB10-277 CDFB103P-277

CDDH16 CD3FB103P-277 CDSC12

CD3FB16

CD3FB10-277

Wire Nuts Coupler Small Coupler Wall Plate

WALL PLATE LABELING SYSTEM

(for use with wall plate that contains label holding slot)

These dimmer wall plates contain a label holding slot. A

0.33" x 1.5" label can be placed in this label holding slot.

These labels can be printed from an Avery®standard

template: Divider tab inserts 8-Tabs or equivalent.

Install the label with the following procedure:

1. Disconnect power to the circuit by removing fuse or

turning circuit breakers OFF.

2. Remove the wall plate by

placing a small flat head

screwdriver into one of

the four slots located at

the top and bottom of the

wall plate. Gently twist a

half turn until the plate

pops off.

3. Slide the label in from the

back side of the wall plate

(as shown at right).

Compatible

P&S Cat #

CDFB5

CDFB8

CDFB53P

CDFB83P

CDFB10

CDFB16

CDFB103P

CDFB163P

CDFB7-277

CDFB10-277

CDFB73P-277

CDFB103P-277

Model

REZ-132-SC, REZ-2S32-SC, REZ-3S32-SC, REZ-154, REZ-2S54,

REZ-1Q18-M2, REZ-2Q18-M2, REZ-1T42-M2, REZ-2T42-M3,

REZ-1TTS40/REZ-1TTS40-SC, REZ-2TTS40/REZ-2TTS40-SC,

IEZ-2S24-D, REB-2S26-M1-LS-DIM/REB-2S26-M1-BS-DIM

2W-T426-120-1-S, 2W-T426-120-2-S, 2W-T432-120-1-S,

2W-T432-120-2-S, 2W-T832-120-1-S, 2W-T832-120-2-S

QTP1x32T8/UNV DIM, QTP2x32T8/UNV DIM, QTP3x32T8/UNV

DIM, QTP4x32T8/UNV DIM

VEZ-132-SC, VEZ-2S32-SC, VEZ-3S32-SC, VEZ-154, VEZ-2S54,

VEZ-1Q18-M2, VEZ-2Q18-M2, VEZ-1T42-M2, VEZ-2T42-M3,

VEZ-1TTS40/VEZ-1TTS40-SC, VEZ-2TTS40/VEZ-2TTS40-SC,

IEZ-2S24-D

QTP1x32T8/UNV DIM, QTP2x32T8/UNV DIM, QTP3x32T8/UNV

DIM, QTP4x32T8/UNV DIM

Voltage

120VAC

60 HZ

277VAC

60 HZ

Ballast

Manufacturer

Advance

Lutron

Sylvania/

Osram

Advance

Sylvania/

Osram

CD3FB16

CD3FB163P

CD3FB10-277

CD3FB103P-277

120VAC

60 HZ

277VAC

60 HZ

Lutron

Lutron

FDB-T418-120-1-S, FDB-T418-120-2-S,

FDB-T426-120-1-S, FDB-T426-120-2-S,

FDB-T418-120-1-S, FDB-T418-120-2-S,

FDB-T426-120-1-S, FDB-T426-120-2-S,

FDB-T432-120-1-S, FDB-T432-120-2-S,

FDB-T442-120-1-S, FDB-T442-120-2-S,

FDB-1643-120-1, FDB-1643-120-2,

FDB-1643-120-3, FDB-2227-120-1,

FDB-2227-120-2, FDB-2227-120-3,

FDB-2243-120-1, FDB-2243-120-2

FDB-T418-277-1-S, FDB-T418-277-2-S,

FDB-T426-277-1-S, FDB-T426-277-2-S,

FDB-T418-277-1-S, FDB-T418-277-2-S,

FDB-T426-277-1-S, FDB-T426-277-2-S,

FDB-T432-277-1-S, FDB-T432-277-2-S,

FDB-T442-277-1-S, FDB-T442-277-2-S,

FDB-1643-277-1, FDB-1643-277-2,

FDB-1643-277-3, FDB-2227-277-1,

FDB-2227-277-2, FDB-2227-277-3,

FDB-2243-277-1, FDB-2243-277-2

HL3-T426-120-1-S, HL3-T432-120-1-S,

FDB-T524-120-1, FDB-T524-120-2,

FDB-T539-120-1, FDB-T539-120-2,

FDB-T554-120-1, FDB-T554-120-2,

FDB-2427-120-1, FDB-2427-120-2,

FDB-2427-120-3, FDB-3627-120-1,

FDB-3627-120-2, FDB-3627-120-3,

FDB-4827-120-1, FDB-4827-120-2,

FDB-4827-120-3, FDB-6027-120-1,

FDB-6027-120-2, FDB-7280-120-1,

FDB-8480-120-1, FDB-9680-120-1,

H3DT832CUNV110, H3DT832CUNV117,

H3DT832CUNV210, H3DT832CUNV217

HL3-T426-277-1-S, HL3-T432-277-1-S,

FDB-T524-277-1, FDB-T524-277-2,

FDB-T539-277-1, FDB-T539-277-2,

FDB-T554-277-1, FDB-T554-277-2,

FDB-2427-277-1, FDB-2427-277-2,

FDB-2427-277-3, FDB-3627-277-1,

FDB-3627-277-2, FDB-3627-277-3,

FDB-4827-277-1, FDB-4827-277-2,

FDB-4827-277-3, FDB-6027-277-1,

FDB-6027-277-2, H3DT832CUNV110,

H3DT832CUNV117, H3DT832CUNV210,

H3DT832CUNV217

P&S

Cat. # Voltage Ballast

Manufacturer 1% – Hi-lume, Hi-lume 3D

Model

5% – Compact SE 10% – Eco-10

Table 1

Table 2

E3-T514C-120-1, E3-T514C-120-2,

E3-T521C-120-1, E3-T521C-120-2,

ECO-T528-120-1, ECO-T528-120-2,

ECO-T524-120-1, ECO-T524-120-2,

ECO-T5H39-120-1, ECO-T5H39-120-2,

ECO-T554-120-1, ECO-T554-120-2,

ECO-T539-120-1, ECO-T539-120-2,

ECO-T539-120-3, ECO-T540-120-1,

ECO-T540-120-2, ECO-T540-120-3,

ECO-T550-120-1, ECO-T550-120-2,

ECO-T817-120-1, ECO-T817-120-2,

ECO-T817-120-3, ECO-T825-120-1,

ECO-T825-120-2, ECO-T832-120-1-L,

ECO-T832-120-1-T, ECO-T832-120-2-L,

ECO-T832-120-2-T, ECO-T832-120-3

E3-T514C-277-1, E3-T514C-277-2,

E3-T521C-277-1, E3-T521C-277-2,

ECO-T528-277-1, ECO-T528-277-2,

ECO-T524-277-1, ECO-T524-277-2,

ECO-T5H39-277-1, ECO-T5H39-277-2,

ECO-T554-277-1, ECO-T554-277-2,

ECO-T539-277-1, ECO-T539-277-2,

ECO-T539-277-3, ECO-T540-277-1,

ECO-T540-277-2, ECO-T540-277-3,

ECO-T550-277-1, ECO-T550-277-2,

ECO-T817-277-1, ECO-T817-277-2,

ECO-T817-277-3, ECO-T825-277-1,

ECO-T825-277-2, E3-T832C-277-1,

ECO-T832-277-1-L, ECO-T832-277-1-T,

ECO-T832-277-1, E3-T832C-277-2,

ECO-T832-277-2-L, ECO-T832-277-2-T,

ECO-T832-277-2, ECO-T832-277-3

SINGLE GANG INSTALLATION INSTRUCTIONS

1. Disconnect power to circuit by removing fuse or turn

circuit breakers OFF before installing.

2. For existing installations: Remove wall plate and

switch mounting screws, pull existing switch from wall

box. For new installations: Install a 1-gang wall-box.

3. Disconnect existing switch from circuit. 3-way

installation: Identify the “COMMON” wire (wire

connected to the terminal marked common or odd

colored terminal). For “new” installation identify wire

connected to power source or to the load.

4. Connect dimmer as shown in the wire diagram with

appropriate sized wire connectors (see Table 4).

5. Install dimmerinwallbox,withthe word“TOP”up,usingmountingscrewsprovided.

6. Insert the label, attach the wall plate and restore power to the circuit.

7. Dimmer Set-up Adjustments:

a. Incandescent Dimmer: The Full ON voltage can be reduced to save energy

by reducing the Full ON light level. To change the Full ON light level, slide

the dimmer knob up to its full brightness. DISCONNECT POWER FROM

CIRCUIT, and remove the wall plate. Use a small insulated, screwdriver to

adjust the trim potentiometer. Turn down to decrease the Full ON light level.

b.Magnetic Low Voltage Dimmer: The minimum light level may need

adjustment for variations in low voltage transformers. To change the

minimum light level, slide the dimmer knob down to the lowest

brightness. DISCONNECT POWER FROM CIRCUIT, and remove the wall

plate. Use a small insulated, screwdriver to adjust the trim potentio-

meter. Turn down to decrease the minimum light level.

c. Fan Speed Controls: The minimum fan speed level may need adjustment

for variations in fans. To change the minimum fan speed, slide the knob

down to the lowest level. DISCONNECT POWER FROM CIRCUIT, and

remove the wall plate. Use a small insulated, screwdriver to adjust the

trim potentiometer. Turn down to decrease the fan speed. Make certain

that the fan does not “stall” in any of the ON positions as overheating of

the fan may occur. DO NOT USE THE FAN PULL CHAIN TO CHANGE

SPEEDS AFTER THIS CONTROL IS INSTALLED. THE FAN PULL CHAIN

NEEDS TO REMAIN AT THE MAXIMUM SPEED.

d.Dehummer Fan Speed Controls: No adjustments required. Make certain

that the fan does not “stall” in any of the ON positions as overheating of

the fan may occur. DO NOT USE THE FAN PULL CHAIN TO CHANGE

SPEEDS AFTER THIS CONTROL IS INSTALLED. THE FAN PULL CHAIN

NEEDS TO REMAIN AT THE MAXIMUM SPEED.

e. Fluorescent Dimmers “CDFB”

Series: The minimum light level

may need adjustment for variations

in ballasts. To change the minimum

light level, slide the dimmer knob

down to the lowest brightness.

DISCONNECT POWER FROM CIR-

CUIT, and remove the wall plate.

Use a small insulated, screwdriver

to adjust the trim potentiometer.

Turn up to increase the minimum

light level.

WIRING DIAGRAMS

Table 4

WIRING INFORMATION

IMPORTANT NOTES Read the following before installation:

• Requirements for wire strip length and wire connections.

Table 3 - WIRE NUT USAGE CHART

• Use a separate neutral wire for each phase of a multiphase system

containing a dimmer, and for high power single phase applications where

flickering is present.

• All dimmers can be damaged by improper wiring. Check for short circuits

prior to installing the dimmer.

Procedure for short circuit check:

a. Disconnect power to the circuit by removing fuse or turning circuit

breakers OFF.

b. Install a switch instead of the dimmer. Turn the switch to the “on” position.

c. Turn power ON. If the circuit breaker trips, a short is present. If the light

fails to turn ON and OFF with the switch, the wiring may be incorrect.

d. Correct wiring, if necessary and retest.

e. Install the dimmer only after the light operates properly with the switch.

• Protect from dirt and dust. The dimmer can be damaged from contamin-

ates encountered during the construction process. If lighting is required

prior to the construction process completion, then a switch should be

temporarily installed in place of the dimmer. The dimmer should not be

installed until the construction process is complete.

• Any dimmer damaged by improper installation is not covered under warranty.

• It is normal for the dimmer to feel warm during operation.

• Cleaning Instructions: Wipe dimmer with a damp, clean cloth.

DO NOT clean the dimmer with chemicals or cleaning solutions.

Dimmer Catalog # Diagram #

CD700, CD1100, CDLV700, CDLV1100, CD1600, CDLV1600,

CD2000, CDFB5, CDFB8, CDFB10, CDFB16, CDFB7-277, 1

CDFB10-277, CDDH16, CDSC6, CDSC12

For Single Pole Installation of: CD703P, CD1103P, CDLV703P,

CDLV1103P, CD1603P, CDLV1603P, CD2003P, CDFB53P, CDFB83P, 2

CDFB103P, CDFB163P, CDFB73P-277, CDFB103P-277

For 3-Way Installation of: CD703P, CD1103P, CDLV703P,

CDLV1103P, CD1603P, CDLV1603P, CD2003P, CDFB53P, 3

CDFB83P, CDFB103P, CDFB163P, CDFB73P-277, CDFB103P-277

For 4-Way Installation of: CD703P, CD1103P, CDLV703P,

CDLV1103P, CD1603P, CDLV1603P, CD2003P, CDFB53P, CDFB83P, 4

CDFB103P, CDFB163P, CDFB73P-277, CDFB103P-277

CD3FB16, CD3FB10-277 5

For Single Pole Installation of: CD3FB163P, CD3FB103P-277 6

For 3-Way Installation of: CD3FB163P, CD3FB103P-277 7

Wire Combinations Strip Lengths Color

1#14 & 1#16; 1#14 & 2#18; 2,3#16; 1/2" Except 9/16" Orange

1#16 & 1-3#18; 3-5#18; 2#18 For #16 & #18 AWG

1#10 & 1#14; 1#12 & 1#14 2, 3#14; 1/2" Except 5/8" Yellow

2#14 & 1,2#16; 2#14 & 2,3#18; For #16 AWG

1#14 & 1-4#16; 1#14 & 1-4#18

1#10 & 1,2#12; 1#10 & 1-3#14; 2,3#12; 7/16" Except 1/2" Red

1#12 & 1-3#14; 1#12 & 3#16; 3,4#14 For #16

1#14 & 1,2#16; 1#14 & 1,2#16; 7/16" For #14 & #16 Ivory

2,3#16; 2-5#18 1/2" For #18

Use Only Copper Wire With This Device.

DIAGRAM 1 (Single-Pole Wiring)

DIAGRAM 2 (Single-Pole Wiring Using 3-Way Preset Dimmer)

DIAGRAM 3 (3-Way Wiring)

DIAGRAM 4 (4-Way Wiring)

DIAGRAM 5 (Single-Pole Wiring)

DIAGRAM 6 (Single-Pole Wiring Using 3-Way Preset Dimmer)

DIAGRAM 7 (3-Way Wiring)

CAUTION: To be installed by a certified electrician or other qualified person.

WARNING: To prevent severe shock or electrocution, always turn power

OFF at the service panel before installing this dimmer, working on the

circuit, or changing a lamp.

Knob

Trim

Potentiometer

NOTE: Never

adjust trim

potentiometer

when circuit

is live.

MULTI GANG INSTALLATION INSTRUCTIONS

FINS ARE NOT REMOVED

NOTE: A 3-gang Installation of Narrow Dimmers is shown and described

below. Any Combination of Wide and Narrow Dimmers will gang the same way.

1. Select the correct box size from Table 6.

Table 6 – Wall-box Gang Requirements – FINS are NOT REMOVED

3. Connect the dimmer as shown in the wiring diagram using the appropriate

sized wire connectors.

4. With the word “TOP” up, install dimmer in the wall box using mounting

screws provided (leave mounting screws “finger tight” at this point).

5. Attach the Couplers between the Dimmers with the screws that were

removed in step 2.

Remove this screw to remove End Cap

End Cap

Remove this screw to remove End Cap

*Wall Box Requirements for Ganging an Even Number of Narrow Dimmers.

4+1 set up shown below:

Chase nipple

4-gang

wall box

1-gang

wall box

2.712

Narrow Dimmers

01 23 4 56

0011+1* 4 4+1* 7 7+1*

113 56 8 911

245 78 10 11 13

368 911 12 14 15

49 10 12 13 15 16 -

511 13 14 16 ––-

614 15 –– – –

Wide Dimmers

MULTIPLE GANGING OF DIMMERS

Any combination of dimmer models may be ganged together. Using a vise or heavy-duty pliers, remove the fins on either or both sides of the heat sink, as

necessary. Dimmers can be ganged without removing fins by proper selection and placement of outlet boxes (see Table 6 and Table 7). When Dimmers are ganged,

De-rate the maximum load according to the following De-Rating Table 5:

Table 5 – Derating for Multi-Gang Installations

2. Remove the End Cap between adjacent dimmers (2 screws for each End

Cap). Keep these screws as they will be needed at step #5.

NOTE: The End Cap that is not between dimmers does not get removed.

Fins are NOT Removed Fins are Removed

Dimmer 1-Gang 2-Gang 3- or more Gang 2-Gang 3- or more Gang

Catalog # Installation Installation Installation Installation Installation

CD700 700W 700W 700W 700W 700W

CDLV700 700VA 700VA 700VA 700VA 700VA

CD703P 700W 700W 700W 700W 700W

CDLV703P 700VA 700VA 700VA 700VA 700VA

CD1100 1100W 1100W 1000W 1000W 900W

Narrow CDLV1100 1100VA 1100VA 1000VA 1000VA 850VA

Dimmers CD1103P 1100W 1100W 1000W 1000W 950W

CDLV1103P 1100VA 1100VA 1000VA 1000VA 850VA

CDFB5 5A 5A 5A 5A 5A

CDFB8 8A 8A 8A 7.7A 6.3A

CDFB53P 5A 5A 5A 5A 5A

CDFB83P 8A 8A 8A 7.7A 6.3A

CDSC6 6A 6A 6A 6A 6A

CDDH16 1.6A 1.6A 1.6A 1.6A 1.6A

CD3FB16 16A 16A 16A 16A 16A

CD3FB163P 16A 16A 16A 16A 16A

CD3FB10-277 10A 10A 10A 10A 10A

CD3FB103P-277 10A 10A 10A 10A 10A

CD1600 1600W 1600W 1600W 1600W 1550W

CDLV1600 1600VA 1600VA 1600VA 1600VA 1550VA

CD1603P 1600W 1600W 1600W 1600W 1550W

CDLV1603P 1600VA 1600VA 1600VA 1600VA 1550VA

CD2000 2000W 2000W 2000W NO FINS TO REMOVE

CD2003P 2000W 2000W 2000W

Wide CDFB10 10A 10A 10A 10A 10A

Dimmers CDFB16 16A 16A 16A NO FINS TO REMOVE

CDFB7-277 7A 7A 7A 7A 7A

CDFB10-277 10A 10A 10A 10A 10A

CDSC12 12A 12A 12A 12A 12A

CDFB103P 10A 10A 10A 10A 10A

CDFB163P 16A 16A 16A NO FINS TO REMOVE

CDFB73P-277 7A 7A 7A 7A 7A

CDFB103P-277 10A 10A 10A 10A 10A

Couplers

6. Tighten the mounting screws, insert the label, attach the wall plate, and

restore power to the circuit.

7. Calibrate the Dimmer if necessary – Refer to Single Gang Installation

Instructions, step #7.

f. Fluorescent Dimmers “CD3FB” Series: No adjustments are required.

The minimum light level is calibrated at the factory and does not

normally require adjustment. If the lamps drop out or flicker at the

minimum dimming level, there may be an installation error.

NOTE: To ensure full lamp life and proper dimming performance, it is rec-

ommended to “season” fluorescent lamps prior to dimming. This is accom-

plished by operating the lamps at maximum light levels for up to 100 hours.

Refer to individual lamp manufacturer for recommended seasoning times.

© 2008 Pass & Seymour/Legrand

P.O. Box 4822, Syracuse, NY 13221-4822

(800-223-4185)

www.passandseymour.com P/N 340872

MULTI GANG INSTALLATION INSTRUCTIONS

FINS ARE REMOVED

NOTE: A 3 gang Installation of

Narrow Dimmers is shown and

described below. Any Combination

of Wide and Narrow Dimmers will

gang the same way.

1. Select the correct box size from

Table 7.

Table 7 – Wall-box Gang Requirements – FINS are REMOVED

2. Remove the End Cap and break the fins between adjacent dimmers (2 screws

for each End Cap). Keep these screws as they will be needed at step #5.

NOTE: The End Cap and the Fins that are not between dimmers do NOT

get removed.

3. Connect the dimmer as shown in the wiring diagram using the appropriate

sized wire connectors.

4. With the word “TOP” up, install dimmer in the wall box using mounting

screws provided (leave mounting screws “finger tight” at this point).

5. Attach the Small Couplers between the Dimmers with the screws that were

removed in step 2.

Narrow Dimmers

0123456

00123456

11345678

23456789

35678910 11

478910 11 12 13

59 10 11 12 13 14 15

611 12 13 14 15 16 17

Wide Dimmers

Fins are removed between adjacent dimmers

6. Tighten the mounting screws, insert the label, attach the wall plate, and

restore power to the circuit.

7. Calibrate the Dimmer if necessary – Refer to Single Gang Installation

Instructions, step #7.

WARRANTIES

Lifetime Warranty. The device you have purchased is warranted under normal use

against defects in workmanship and materials for as long as you own the device. If the

device fails due to manufacturing defect during normal use, return the device for

replacement to the store where purchased or send to:

Pass & Seymour Legrand

50 Boyd Avenue

Syracuse, NY 13209

All requests for replacement must include a dated sales receipt (legible copies

acceptable).

ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO A

PERIOD OF TWO YEARS FROM THE DATE OF PURCHASE. YOUR SOLE AND EXCLUSIVE

REMEDY AGAINST PASS & SEYMOUR LEGRAND UNDER ANY WARRANTY SHALL BE THE

EQUIVALENT REPLACEMENT OF THE DEVICE. IN NO EVENT SHALL ANY WARRANTY

APPLY TO ANY DEFECT ARISING OUT OF ANY ALTERATION OF THE DEVICE, IMPROPER

WIRING, IMPROPER INSTALLATION, MISUSE, ABNORMAL USE OR NEGLIGENCE. IN NO

EVENT SHALL PASS & SEYMOUR LEGRAND BE LIABLE FOR LOST PROFITS, INDIRECT,

SPECIAL, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do

not allow limitations on how long implied warranties last and do not allow exclusion or

limitation of incidental or consequential damages. Some of the above limitations or

exclusions may not apply to every purchaser.

Small Couplers

Remove this

screw to

remove End Cap

End Cap

Remove this

screw to

remove End Cap

Remove fins

between

adjacent

dimmers

using a

vise or

heavy-duty

pliers