Installation Directions

669455-Installation 669455-Installation 669455-Installation 662400 Batch4 unilog cesco-content

669455-Installationsheet 669455-InstallationSheet 669455-InstallationSheet 662400 Batch4 unilog cesco-content

: Pdf 1000298397-Installationsheet 1000298397-InstallationSheet B5 unilog

Open the PDF directly: View PDF .
Page Count: 2

APPLICATION: Quadcast luminaires are designed for outdoor, wet location use

not to exceed 40˚C ambient. Approved for ceiling/surface, parking garage, canopy,

stairwell, low bay and rigid and free swing pendant applications.

NOTE: DO NOT REMOVE LED OPTICAL PANELS, WET LOCATION GROMMETS, OR

FLEXIBLE CORD GLANDS.

TOOLS REQUIRED:

Phillips tip screwdriver, electrical wiring tools, 9/64" Allen® Head Key, wet location

UL Listed wiring connectors, UL Listed wet location junction box (For pendant mount

applications).

ALIGNMENT GUIDE (PARKING GARAGE INSTALLATION):

Align quick mount plate to junction box by aligning arrows with parking garage

driving lanes (FIG. 3). Direction of arrows should be in line with direction of traffic.

CEILING/JUNCTION BOX INSTALLATION:

1. Loosen (do not remove) the two locking screws (FIG. 1). Pivot both locking hinges

out to the left/right sides until they stop.

2. Slide quick mount plate forward until the plate disengages from the housing

(FIG. 2).

3. Unhook quick mount plate from the wire hinge (FIG. 3).

4. Install the quick mount plate onto a wet location junction box (SUPPLIED BY

OTHERS) using the hardware supplied (#8-32x3/4" or #6-32x3/4" screws).

See alignment guide above and the alignment arrows on the quick mount

plate label. (FIG. 3).

5. Hang the luminaire to the quick mount plate by the wire hinge (FIG. 3A).

CAUTION: PLEASE ENSURE WIRE HINGE IS SEATED WITHIN BOTH OF THE

QUICK MOUNT PLATE RETENTION HOOKS. FAILURE TO DO SO MAY RESULT IN

PERSONAL INJURY OR PROPERTY DAMAGE.

ADH120932

Customer First Center

1121 Highway 74 South

Peachtree City, GA 30269

P: 770.486.4800 F: 770.486.4801

www.cooperlighting.com

QuadcastTM LED

Parking Garage/Canopy

Luminaire

Sheet 1 of 2

7/6/2012 IMI-775

SAFETY: This fixture must be wired in accordance with the National Electrical Code

and applicable local codes and ordinances. Proper grounding is required to insure

personal safety. Carefully observe grounding procedure under installation section.

WARNING: Make certain power is OFF before starting installation or attempting any

maintenance. Risk of fire/electric shock. If not qualified, consult an electrician.

• RISK OF ELECTRIC SHOCK—Disconnect power at fuse or circuit breaker before

installing or servicing.

• RISK OF BURN—Disconnect power and allow xture to cool before servicing.

• RISK OF PERSONAL INJURY—Fixture may become damaged and/or unstable if

not installed properly. Tighten all fixture components to their recommended torque

values.

INSTALLATION INSTRUCTIONS

IMPORTANT: READ BEFORE INSTALLING FIXTURE.

RETAIN FOR FUTURE REFERENCE.

WARNING: Make certain power is OFF before starting installation or attempting any maintenance.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufciently for user’s purpose, please contact

your nearest representative. NOTE: Specications and dimensions subject to change without notice.

—continued

FIG. 1

Locking

Screw

Locking

Screw

Locking

Hinge

Locking

Hinge

Quick Mount Plate

FIG. 2

Slide Quick

Mount Plate

FIG. 3

Locking

Screw

Locking

Screw

Locking

Hinge

Locking

Hinge

Wire Hinge

Quick Mount Plate

Wet Location

Junction Box

(Supplied by Others)

Housing

Plate

Align Arrows with

Driving Lane

Alignment Guide Label

FIG. 3A

Wire Hinge

Retention Hooks

Make electrical connections (FIG. 4).

NOTE: ENSURE WIRING IS CENTERED THROUGH WIRE HINGE.

a. Connect supply side line voltage wire to black lead.

b. Connect supply side neutral wire to white lead.

c. Connect supply side ground wire to green lead.

NOTE: INSTALLER MUST USE UL LISTED WET LOCATION APPROVED WIRING

CONNECTIONS INSIDE UL LISTED WET LOCATION JUNCTION BOX (SUPPLIED BY

OTHERS).

6. After electrical connections are made, push the wire splices through the center

hole of the quick mount plate. Swing and lift the luminaire into position while

maintaining tension on wire hinge. FAILURE TO MAINTAIN TENSION MAY RESULT

IN THE WIRE HINGE BECOMING DISLODGED. The metal tabs on the quick mount

plate will align with openings in the housing plate. With luminaire lifted in place,

slide the luminaire in the direction of the locking hinges. A “click” sound will

occur when the luminaire is fully seated.

7. Pivot both locking hinges back into place and tighten locking screws to

10 inch-pounds (FIG. 5).

RIGID OR FREE-SWING PENDANT INSTALLATION:

1. Install UL Listed wet location junction box (SUPPLIED BY OTHERS) to pendant pipe

(SUPPLIED BY OTHERS) and run supply wires down through pendant pipe and into

wet location junction box (Per NEC Guidelines).

2. Refer to CEILING/JUNCTION BOX INSTALLATION steps above to install.

LED OPTICAL ROTATION (FIG. 6)

The LED optical panels can be rotated to provide a range of lighting distributions.

1. Loosen the 9/64" Allen Head set screw to allow rotation of the LED optical

panel to the desired position.

2. Tighten set screw to 15 inch-pounds once desired angle is achieved.

MAINTENANCE

A regular maintenance schedule should be followed to retain optimal

light output and thermal performance. Optical lens cleaning should

be performed with a clean dry cloth to remove any dust or other

contaminants. Additional cleaning can be performed with

non-abrasive acrylic cleaning solution.

OPTIONAL FIELD INSTALLED ACCESSORIES (ORDER SEPARATELY)

ADH120932

Customer First Center

1121 Highway 74 South

Peachtree City, GA 30269

P: 770.486.4800 F: 770.486.4801

www.cooperlighting.com

QuadcastTM LED

Parking Garage/Canopy

Luminaire

Sheet 2 of 2

7/6/2012 IMI-775

INSTALLATION INSTRUCTIONS

IMPORTANT: READ BEFORE INSTALLING FIXTURE.

RETAIN FOR FUTURE REFERENCE.

WARNING: Make certain power is OFF before starting installation or attempting any maintenance.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufciently for user’s purpose, please contact

your nearest representative. NOTE: Specications and dimensions subject to change without notice.

FIG. 4

FIG. 5

Locking

Screws

FIG. 6

Set Screw

Angle

Indicator

11

10

9

8

765

4

3

2*

1

Set Screw

Location Angle

of Degrees Location Angle

of Degrees

Factory

Pre-set* 15° 6 75°

1 5° 7 90°

215° 8 105°

3 30° 9 120°

4 45° 10 135°

5 60° 11 150°

PENDANT BIRD GUARD (QDPBG)

Pendant

(Supplied by

Others) Bird Guard

OCCUPANCY SENSOR (QDOCC)

Occupancy

Sensor