Installation Directions

62343-Installationsheet 62343-InstallationSheet 62343-InstallationSheet 078477 Batch10 unilog cesco-content

35023-Installationsheet 35023-InstallationSheet 35023-InstallationSheet 078477 Batch2_1 unilog cesco-content

: Pdf 1000332179-Installationsheet 1000332179-InstallationSheet B2 unilog

Open the PDF directly: View PDF .
Page Count: 2

RENOIR II

SWITCH & REMOTE DIMMING CONTROL

Cat. Nos. AWRRG, AWSRG, AWSRT, AWWMG, AWWMT, AWWRG & AWWRT

INSTALLATION

WARNINGS AND CAUTIONS:

• TO AVOID FIRE, SHOCK OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!

• TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH ELECTRICAL CODES AND REGULATIONS.

• IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT AN ELECTRICIAN.

• DO NOT GANG VERTICALLY.

• ONLY INSTALL FOR THE ALLOWED LOAD TYPES. INSTALLATION FOR ANY OTHER LOAD TYPE WILL VOID WARRANTY AND POSSIBLY CAUSE DAMAGE TO

THIS DEVICE AND/OR CONNECTED EQUIPMENT.

• USE THIS DEVICE WITH COPPER OR COPPER CLAD WIRE ONLY.

Installation Requirements:

• Thesedevicesaredesignedforinstallationintoametal2"x3"(5.08cmx7.62

cm)singlegangormulti-gangdevicebackbox.2-1/2"(6.35cm)ordeeper

backboxesarerequired.Thesedevicesarenotdesignedforamulti-gangeld

conguredbox.Insomeinstallationswhereconduitentryisfromtheside,or,in

multi-ganginstallationswherenipplesbetweentwoadjacentboxesareused,

deeperbackboxesmaybenecessary.Testtinstallationpriortorough-in.

• Installationofmultipledevicesintoasingleboxmayrequirede-ratingandother

specicinstallationprovisions.ReferenceMulti-Gang Installationsformore

details.

•

Asdevicesventtop/bottom,devicesshouldnotbeinstalledvertically(oneoverthe

other).

• Toavoidickering,ashing,orlightsononedeviceadjustingwhenanother

device’slevelischanged,donotshareneutrals.Runseparateneutralsforeach

loadcircuitbacktothedevice.(See Figure 1).

Installation Instructions:

1. WARNING: TO AVOID FIRE, SHOCK OR DEATH; TURN OFF POWER AT

CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE

WIRING!

2.Removeexistingwallplateandswitch,ifapplicable.

3.Remove5/8"(1.6cm)ofinsulationfromeachcircuitconductor.Makesurethe

endsofwiresarestraight.

4.ConnectwiresperWIRINGDIAGRAMondeviceasfollows:Twiststrandsofeach

leadtightlytogetherand,withcircuitconductors,pushrmlyintoappropriatewire

connector.Screwconnectorsonclockwisemakingsurenobareconductorsshow

belowthewireconnectors.Secureeachconnectorwithelectricaltape.

5.Installationmaynowbecompletedbycarefullypositioningallwirestoprovide

roominoutletboxfordevice.Mountdeviceintoboxwithmountingscrews

supplied.Snapfaceplateintoplace.

6.Installdevicecontrolpushbuttonandcontrolassembly(see Figure 2).

7.Restorepoweratcircuitbreakerorfuse.Installation is complete.

8.TestDeviceoperation.

INPUT - 120 - 277 VAC 60 HZ OUTPUT-AWWMG-00X&AWWMT-00X-15A

Features and Operation:

• TurnDeviceONorOFF–PressingtheswitchwillturnthedeviceONifthe

deviceisOFF.IfthedeviceisON,pressingtheswitchwillturnthedeviceOFF.

• SetDeviceLevel–Adjusttheknoborslidertosetthedesiredoutputlevel.When

thedeviceturnsON,thedevicealwaysturnsONtothelevelsetbytheslideror

knob.

• SetCutoffLevel–Thecutofflevelisthelowestvoltagethedimmerwilloutput

beforeshuttingOFF.Tosetthecutofflevel,adjusttheknoborslidertothe

maximumoutput.Slowlylowertheoutputtothedesiredcutofflevel,thenpush

andholdthepowerbuttonfor5seconds.Thedimmerwilladjusttothenewlevel.

Toresetthecutofflevelto0,adjusttheknoborslidertotheminimumoutput,then

pushandholdthepowerbuttonfor5seconds.Ifyourloadisickering,notturning

ON,orsufferingfromanyothererraticbehaviorattheminimumsetting,raising

thecutofflevelmayeliminatetheproblem.

• PresetOperation–Whiledeviceisoff,setlevelofdevice.Thenpressbutton.The

devicewillturnonatthesetlevel.

• PowerRestore–Uponrestorationofpower,thedeviceturnsONtothestateit

wasinatthetimeofpowerloss.

• 5-WayOperation–Linktogether2,3,4,or5devicesformulti-waydimming.

• LEDLocator–AtthebottomoftheswitchisanLEDlocator.Thislocator

illuminateswhenthedeviceisOFFsoyoucanndthedeviceinthedark.

• RemoteControl–Ifyouareusingaremote,theoperationattheremoteis

identicaltotheoperationatthemaster.Aslightreactiondelaymaybenoticedif

operatinglevelchangesveryquickly.

ForTechnicalAssistanceCall:1-800-824-3005(U.S.A.Only)www.leviton.com

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

LevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenetofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforveyearsfromthepurchasedate.Leviton’sonlyobligation

istocorrectsuchdefectsbyrepairorreplacement,atitsoption,ifwithinsuchveyearperiodtheproductisreturnedprepaid,withproofofpurchasedate,andadescriptionoftheproblemtoLevitonManufacturingCo.,Inc.,Att:QualityAssuranceDepartment,201North

ServiceRoad,Melville,NewYork11747.Thiswarrantyexcludesandthereisdisclaimedliabilityforlaborforremovalofthisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperlyorinanimproperenvironment,overloaded,misused,opened,

abused,oralteredinanymanner,orisnotusedundernormaloperatingconditionsornotinaccordancewithanylabelsorinstructions.Therearenootherorimpliedwarrantiesofanykind,includingmerchantabilityandtnessforaparticularpurpose,butifanyimplied

warrantyisrequiredbytheapplicablejurisdiction,thedurationofanysuchimpliedwarranty,includingmerchantabilityandtnessforaparticularpurpose,islimitedtoveyears.Levitonisnotliableforincidental,indirect,special,orconsequentialdamages,including

withoutlimitation,damageto,orlossofuseof,anyequipment,lostsalesorprotsordelayorfailuretoperformthiswarrantyobligation.Theremediesprovidedhereinaretheexclusiveremediesunderthiswarranty,whetherbasedoncontract,tortorotherwise.

PK-93969-10-00-2A

Align flats when

installing knob

Center tab in opening

Figure2-RemoteDimmerAssembly

RotaryDevice SlideDevice

Wiring Diagram

Switch Control

LOAD

Black

Blue

Neutral (White)

Hot (Black)

White

White Yellow

For use in multi-way

control (remote)

applications.

Cap wire if not used.

Ground (Green)

Line

120-277VAC

60 Hz

Figure1-DONOTshareneutralwires

Blue

Hot (Black)

Neutral (White)

White

White

Load

Blue

Black

Black

White

Yellow

Yellow

Green

Ground

White

Hot (Black)

Neutral (White)

–

Load

X

–

Run a separate neutral wire

for each control circuit

–

Run a separate neutral wire

for each control circuit

DO NOT

share

neutral

wires

Green

Ground

PK-93969-10-00-2A

©2012LevitonMfg.Co.,Inc.

Multi-WayControl:

TheRenoirIIproductlinesupportsupto5-waycontrol.Anycombinationof

Dimmers,

FanControls,Switches,orRemotesaresupportedwithaMAXIMUM OF

5 DEVICES.TotalrunlengthfromendtoendisMAXIMUM 250 FEET.Remotes

requireUncontrolledHot,Neutral,&Groundforproperoperation.Onetravelerwireis

toruninbetweenallmastersandremotes.Remotesdraw15mApower(ea)fromthe

Controltowhichtheyareconnected.

NOTE:RemoteHot/NeutralshouldideallybefedfromthesamecircuitastheMaster.If

thisisnotpossible,ensurethatthemasterandremotearebothfedfromthesamephase.

Backbox - # Gangs

Wallplate Part #

Device Configuration

Backbox - # Gangs

Wallplate Part #

Device Configuration

Backbox - # Gangs

Wallplate Part #

Device Configuration

Backbox - # Gangs

Wallplate Part #

Device Configuration

Number & Type of NARROW

Number & Type of WIDE

0

1

2

3

0

4**

N+N+N

AWP00-30x

2

N*+*N

AWP00-20x

1

N

AWP0F-10x

1

6**

W+N+N+N

AWP00-31x

4

W+N*+*N

AWP00-21x

3

W+N

AWP0F-11x

1

W

AWP0F-01x

2

7

W+N*+N*+*N+W

AWP00-32x

6

W+N*+*N+W

AWP00-22x

5 or 6

W+N+W

AWP0F-12x

4

W+W

AWP0F-02x

3

9

W*+*W+N*+N*+*N+W

AWP00-33x

8

W*+*W+N*+*N+W

AWP00-23x

8

W+W+N+W

AWP0F-13x

6**

W+W+W

AWP0F-03x

Basic Configurations

Multi-Gang Installations:

Amulti-gangedinstallationexistswhenmultipledevicesareinstalledinthesame

backbox.Inmulti-ganginstallations,thefollowingmayberequired:

- Devicede-rating    -Finremoval

- Useofjoinerbarsforadjacentdevices. - Backboxsize

NOTE: TEST FIT DEVICE INSTALLATION WITH THE WALL PLATE PRIOR TO

BREAKING FINS OR INSTALLING DEVICES TO ENSURE YOU UNDERSTAND ALL

REQUIREMENTS.

1.

Findthecellsthatcorrespondtoyourapplicationbyidentifyingtherowwiththe

numberofwideheatsinkdevicesyouhave,andthecolumnsthatcorrespond

tothenumberofnarrowheatsinkdevicesyouhave.Inthecellyou’llndthe

following:

2.

Thenumberindicatesthenumberof“Gangs”required.

3.

Thelettersunderthenumberindicatetheorderdevicesshouldbeinstalled,

N=narrow,W=wide.

4.-W*=rightnbreak-offonwidedevice,N*=rightnbreak-offonnarrowdevice.

 -*W=leftnbreak-offonwidedevice,*N=leftnbreak-offonnarrowdevice.

 -*W*=nbreak-offonbothsidesofwidedevice,*N*=nbreak-offonbothsidesof

narrowdevice.

5.**indicatesthatuseofjumperbarsisrequired.Jumperbarscanbefoundinthekit

withthefaceplate.

6. Replace'x'inthefaceplatepartnumberwiththedesiredcolor:W=White,I=Ivory,

A=Almond,T=LightAlmond,E=Black,G=Gray,K=24KGold,L=SatinStainless,

R=AntiqueBronze,B=BrushedBrass.

NOTE:Metalnishesarenotavailableoncustomfaceplates.

BasicWIDE/NARROWcongurations,foradditionalcongurationssee:

www.leviton.com/RENOIRII

BackBoxSize&JoinerBars:

Todeterminetherequiredback-boxsizeinmulti-ganginstallations,reference

tablebelow.Inapplicationswherethedevicesdonotlineupwithbackboxdevice

mountingholes,usejoinerbarstojointhecontrolstogether.ReferenceFigure 5.

De-ratings:

Whennsarebroken,somedevicesmustbede-rated.Referencetablebelowto

determinethedeviceratingswhen0,1,or2nsareremoved.

Switches-120-277VAC/VCA,60Hz

Useonlyforresistive,incandescent,inductive,ballastormotorload.

Switches

AWWMG-0D_

AWWMT-0D_

Amps

VA @ 120V

FLA

VA @ 120V

VA @ 230V

VA @ 277V

VA @ 230V

VA @ 277V

0, 1 or 2 fins

removed

1HP

15.0

1.5HP

1.5HP

1800

12.0

4150

3450

FinRemoval:

Whenitisdesiredtoinstalldevicesinassmallaspaceaspossible,allinsidensoflike

sized,adjacentdevicescanbebrokenoff.Figure 4showhowtobreakoffnsandthe

specicorderinwhichmultipledevicesmustbeinstalledinmulti-ganginstallations.

MULTI-GANGINSTALLATIONREQUIREMENTS

Additional-SingleGangBox

Multi-WayControlWiringDiagram

Maximum 5 Devices, Dimmers, Remotes or Fan Controls

Maximum 250 feet

Device/Switch

Maximum 5 Devices, Dimmers, Remotes or Fan Controls

Maximum 250 feet

Remote

Device/Switch Remote

Device/Switch Remote

Device/Switch

Multiple Device/Switches and Remote Device/Switches

Master

Device/Switch Remote

Device/Switch Remote

Device/Switch Remote

Device/Switch Remote

Device/Switch

Hot

Neutral

Ground

Traveler

Hot

Neutral

Ground

Hot

Neutral

Ground

Traveler

Hot

Neutral

Ground

Traveler

Hot

Neutral

Ground

Traveler

Dimmed Hot

Neutral

Ground

LOAD

Hot

Neutral

Ground

Traveler

Hot

Neutral

Ground

Hot

Neutral

Ground

Traveler

Hot

Neutral

Ground

Traveler

Hot

Neutral

Ground

Traveler

Dimmed Hot

Neutral

Ground

LOAD

Dimmed Hot

Neutral

Ground

LOAD

Multiple Remote Device/Switches

Load in between Master Device/Switch and Remote Device/Switch

Master Device/Switch Remote Device/Switch

Dimmed Hot

Neutral

Ground

Hot

Neutral

Ground

Traveler

Hot

Neutral

Ground

LOAD

Load after Remote Device/Switch and Master Device/Switch

Master Device/SwitchRemote Device/Switch

Hot

Neutral

Ground

Hot

Neutral

Ground

Dimmed Hot

Neutral

Ground

Traveler

LOAD

Master

Device/Switch

Figure4-FinRemoval

Back view of devices shown

Break off these fins

DO NOT Break off these fins

Break off these fins

Fin break off points

Figure5-JoinerBar

Narrow/Narrow

Wide/NarrowWide/Wide

Joiner Bar

Joiner Bar

3/4" space (use chase nipple)

3-1/2" deep

back box is

required

Four-gang wallbox Single-gang

wallbox