Installation Directions

: Pdf 1000339675-Installationsheet 1000339675-InstallationSheet B3 unilog

Open the PDF directly: View PDF .
Page Count: 2

Step 8. Remove screw and cover from

SPLICE COMPARTMENT.

Step 9. With hex key (allen wrench) pro-

vided, loosen set screws on UPPER AND

LOWER TERMINALS. Remove cord.

Step 10. Slide cord sleeve tube towards

stripped end of wire until stripped end just

disappears into tube. DO NOT FULLY

REMOVE TUBE FROM CORD.

Step 11. Using cord sleeve tube as a

threading device insert tube into bottom of

shade and thread through hole in top of

shade (or through center hole in spider-

type shades). Simultaneously push wire

up through shade while pulling on cord

sleeve tube.

Step 12. Push/Pull on cord until it is com-

pletely through the cord sleeve tube.

Step 13. IF NOT SHORTENING CORD,

PROCEED TO STEP 20.

Caution: To reduce the risk of fire and electrical shock use these products only with the appropriate Juno trac system or monopoints.

WARNING: Make sure power is off before assembly.

IMPORTANT SAFETY INSTRUCTIONS ASSEMBLING CORD SET TO SHADE

Step 1. Read all instructions completely

before beginning installation. Keep these

instructions in a safe place for future

reference.

Step 2. To reduce the risk of fire and burns,

do not install pendant cords where the

exposed conductor can be shorted or

contact any conductive material.

Step 3. If pendant shade can be acciden-

tally touched it is recommended that lamp

wattage be reduced to 35 watts.

Step 4. Do not install any shade closer then

6 inches (15.25 cm) from any curtain or

similar combustible materials.

Step 5. To reduce the risk of fire and over-

heating make sure all connections are tight.

Step 6. Turn off the electrical power before

modifying the lighting system in any way.

Step 7. Qualified electricians, in accordance

with local electrical codes should perform all

installations.

SAVE THESE INSTRUCTIONS

SHORTENING CORD SET

Step 14. Determine cord length desired by

holding cord set alongside installed, not

electrically energized splice compartment.

Cut cord at point level with top edge of

UPPER TERMINAL.

Step 15. Remove adapter from trac or

monopoint.

Using CORD SLEEVE as a

threading device pass cord

through shade.

Simultaneously push & pull

sleeve and cord through

fixture.

SAFETY CAPSULE

SPRINGS

When using HALOGEN

BI-PIN CAPSULE lamps,

the frosted glass

SAFETY CAPSULE

(provided) MUST be

installed.

STEPS: 8, 9, 13

UPPER 

TERMINAL

SET 

SCREWS

LOWER

TERMINAL

CUT

TO EDGE

OF UPPER

TERMINAL

SPLICE COMPARTMENT

STEPS: 10, 11, 12

For TP, TLP and TFP Pendant Cord Sets

INSTALLATION INSTRUCTIONS

© 2016 Acuity Brands Lighting, Inc. Rev 5/16 P5020 pg 1 of 2

1300 South Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • www.junolightinggroup.com

Product Services Phone (888) 387-2212

SELECTING AND INSTALLING LAMPS

HALOGEN BI-PIN CAPSULES are popular for use in pendants due to excellent color rendering, efficiency and evenness of illumination. Holding lamp

with plastic bag or soft cloth, insert in socket. DO NOT TOUCH LAMP WITH BARE FINGERS. These lamps MUST BE USED WITH GLASS SAFETY

CAPSULE/DIFFUSER (supplied).

XELOGEN® FROSTED BI-PIN CAPSULES have performance similar to halogen bi-pin capsules but with longer life, no handling restrictions and do not

require use of GLASS SAFETY CAPSULE.

MR16CG (Cover Glass) lamps provide more downlighting but do not illuminate glass shades well. They are well suited for metal shades. When using

MR16CG lamps, bend CAPSULE SPRINGS outward before installing lamp. To use MR16CG lamp with TLP328 DISC shade, back off socket screws

one full turn, remove springs, and retighten screws.

Shades are rated at 50 WATTS MAXIMUM, except:

For metal shades TLP315 FLUTE MIDNIGHT AND SILVER FINISHES and TLP327 RLM MIDNIGHT FINISH ONLY, shades are rated for 37 WATTS

MAXIMUM! If a shade can be accidentally touched, it is recommended that lamp wattage be reduced to 37 WATTS OR LESS!

Step 16. Push back OUTER BRAIDED CONDUCTOR enough

to allow it to expand in diameter.

Step 17. Using a small pair of scissors snip a slit in the OUTER

BRAIDED CONDUCTOR lengthwise along the cord 1/2” long.

Step 18. Pull OUTER BRAIDED CONDUCTOR off and to the side

of the inner conductor and snip off braided conductor as squarely

as possible.

Step 19. Using fingers, tightly wrap OUTER BRAIDED

CONDUCTOR around insulation of INNER CONDUCTOR.

When finished, 1/2” of the insulated INNER CONDUCTOR should

remain visible.

Step 20. With pliers hold onto cord at point shown in illustration

below. Strip insulation off of INNER CONDUCTOR 1/4”.

Twist wires into tight bundle.

Step 21. CAUTION: Inspect and trim any loose wires from the

OUTER BRAIDED CONDUCTOR to make sure they cannot in

any way make electrical contact with the exposed end of the INNER

CONDUCTOR.

Step 22. Slowly and gently insert stripped end of cord set into

both terminals. Slight left-and-right rotation of wires can simplify

this operation.

Step 23. Make sure exposed end of INNER CONDUCTOR is fully

inserted into UPPER TERMINAL. Make sure the plastic insulation

does not enter terminal. Tighten set screw securely.

Step 24. Visually inspect to ensure that the OUTER BRAIDED

CONDUCTOR is fully inserted into LOWER TERMINAL and that no

loose wires can reach or come in contact with UPPER TERMINAL.

Tighten set screw securely.

Step 25. Re-check connections and securely tighten both

set screws.

Step 26. Holding the assembly in your hand with your thumb

pressing down on both terminals, pull on the cordset to ensure that

the electrical and mechanical connection is secure. Re-install and

re-tighten as needed.

Step 27. Replace cover and screw.

Step 28. READ “SELECTING AND INSTALLING LAMPS”

BELOW.

ETL CLASSIFIED

CONFORMS TO UL

STD 1598 AND

CSA STD. C22.2

NO.250

3054160

PUSH 

DOWN

OUTER 

BRAIDED

CONDUCTOR

TO EXPAND

DIAMETER

SLIT OUTER 

BRAIDED

CONDUCTOR

1/2"

WITH SCISSORS

1/2"

STEPS: 16, 17

FULLY

REMOVE

OUTER

BRAIDED

CONDUCTOR

1/2"

AND WRAP

STRANDS

TIGHTLY

1/2"

STEPS: 18, 19

INNER CONDUCTOR

HOLD HERE WITH

PLIERS BEFORE

STRIPPING INNER

CONDUCTOR!!!

OUTER BRAIDED

CONDUCTOR

FULL SIZE

STRIP GAUGE

1/4"

STEPS: 20, 21

UPPER 

TERMINAL

NO LOOSE

STRANDS

OF WIRE

ALLOWED

IN THIS

AREA

LOWER

TERMINAL

STEPS: 22 - 26

WARRANTY

Juno Lighting Group warrants that its products are free from defects in material and workmanship for one year from the date of

purchase. Juno Lighting Group’s obligation is expressly limited to repair or replacement, without charge, at Juno Lighting Group’s

factory after prior written return authorization has been granted. This warranty shall not apply to products which have been altered

or repaired outside of Juno Lighting Group’s factory. This warranty is in lieu of all other warranties, expressed or implied, and

without limiting the generality of the foregoing phrase, excludes any implied warranty of merchantability. Also, there are no

warranties which extend beyond the description of the product on the company’s literature setting forth terms of sale.

© 2016 Acuity Brands Lighting, Inc. Rev 5/16 P5020 pg 2 of 2

1300 South Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • www.junolightinggroup.com

Product Services Phone (888) 387-2212

For TP, TLP and TFP Pendant Cord Sets

INSTALLATION INSTRUCTIONS