1000352944 Catalog
2016-10-27
: Pdf 1000352944-Catalog 1000352944-Catalog B6 unilog
Open the PDF directly: View PDF 
.
Page Count: 25
SOLUTIONS
CATALOG
Certification, troubleshooting, and installation
tools for professionals who install and maintain
critical network cable infrastructure
Certification, troubleshooting, and installation
tools for professionals who install and maintain
critical network cable infrastructure
c
r
m
1-800-283-5853 (US and Canada) • www.flukenetworks.com 3
Datacom Cabling
Cable Certication System and Management
Versiv™ Cable Certication System 3
Copper Cable Test Solutions
Copper Cable Test Solutions Product Comparison 4
DSX-5000 CableAnalyzer™ 5
Copper Adapter and Accessories 6
CableIQ™ Qualication Tester 9
MicroMapper™ 10
MicroScanner 2 Cable Verier 10
IntelliTone™ Pro 200 LAN Toner and Probe 11
Pro3000™ Analog Tone and Probe 11
Pocket Toner® 12
TS®100 PRO Cable Fault Finder 13
TS®90/TS®100 Cable Fault Finder 14
LinkWare™ Live 15
Fiber Cable Test Solutions
Fiber Testing, Troubleshooting and Certication
Comparison 16
OptiFiber® Pro OTDR 18
Launch Fibers 19
CertiFiber® Pro 20
FI-7000 FiberInspector™ Pro 22
MultiFiber® Pro 23
SimpliFiber Pro® Optical Power Meter 24
Fiber Test Kits 24
Legacy Test Reference Cords, Adapters and Mandrels 26
Fiber QuickMap™ 27
Fiber OneShot™ PRO 28
Fiber Inspection and Cleaning
FiberInspector™ Mini Video Microscope 29
FiberViewer™ Fiber Microscope 29
VisiFault™ Visual Fault Locator 29
Fiber Optic Cleaning Kits 30
Tools and Test Kits
JackRapid™ Termination Tool 31
Impact Tools 32
Blades 33
Pro-Tool™ Kits 34
Electrical Contractor Telecom Kits 34
Modular Crimper 35
Cable Splicing Knife 35
D-Snips™ 35
Electrician’s Snips 35
Cable Strippers 36
Need-L-Lock™ Crimping Pliers 36
Probe Pic 36
Can Wrench 36
Telephone Butt-Sets and Access Network Test
Telephone Test Set Comparison 37
TS®54 TDR Test Set 38
TS®52 PRO LCD Test Set 39
TS®30 Test Set 40
TS®22 Series Test Sets 40
TS®25D LCD Test Set 41
TS®19 Test Set 41
Modular Adapters 42
Line Cords and Clips 43
Voltage Detector 44
Gold Support
Protect Your Investment with Gold Membership 46
What’s Included with Gold Membership 46
Gold Membership Priviledges 47
Table of Contents
Versiv™ Cable Certification System
Versiv users report spending 1/3 the time on testing and reporting, cutting the total cost of a job by 10%.
Certifying a cable is one part of a process that starts with design of a structured cabling system and ends with systems
acceptance. The faster that process goes, the more protable you’ll be. Unfortunately, there are a lot of things that slow the
process down – testing to the wrong limits, waiting for lead technicians to set up or troubleshoot, and discovering that you have
incomplete results after your team has left the construction site.
Research shows that over 90% of contractors report dealing with issues related to set-up, testing, and reporting every month. It
adds up to a week of wasted labor on a typical 1,000 drop job.
Versiv is designed to eradicate these problems. Its ProjX™ System manages job requirements and progress from setup to systems
acceptance, making sure all tests are completed correctly. The Taptive™ User Interface simplies set up, eliminates errors and
speeds troubleshooting. The LinkWare™ Live cloud service gives you visibility and control of the whole process: you can set
up and track your testers and inspect results from any mobile device while the job is in process. It even lets you upload and
integrate results from multiple testers at multiple jobsites so you can quickly generate reports with the de-facto industry
standard LinkWare PC.
Eliminate the problems, get jobs done faster, and make money every time you use Versiv.
To learn more visit: www.flukenetworks.com/VersivFamily
To congure your Versiv Kit visit: www.flukenetworks.com/VersivConfig
Cable Certification System and Management
1-800-283-5853 (US and Canada) • www.flukenetworks.com
4 5
COPPER
CERTIFICATION
AND TESTING
DSX-5000
CableAnalyzer™
CableIQ™
Qualification Tester
MicroScanner2
Cable Verifier
Supports structured cabling warranties
Meets TIA/ISO certication standards requirements Levels IIe, III, IIIe,
Level IV, and Level V.
Provides pass/fail results 9.9 second Cat 6A
Documents test results
Qualies cabling speed (10/100/VoIP/Gig)
Advanced troubleshooting: Fault Info HDTDX, HDTDR
Basic troubleshooting: distance to break or short
Continuity and wiremap
DSX-
5000
C
ableAna
lyze
r
™
Copper Cable Test Solutions
DSX-5000 CableAnalyzer™
The DSX-5000 CableAnalyzer improves the efciency of copper certication with unmatched speed for
testing Cat 6A and Class FA while meeting IEC Level V—the most stringent accuracy requirement.
The ProjX Management System ensures jobs are done correctly the rst time and helps track progress from
set-up to systems acceptance. Taptive user interface troubleshoots faults faster by graphically indicating
the source of failures including crosstalk, return loss, and shield faults. Analyze test results and create
professional test reports using LinkWare™ Cable Test Management Software.
Fluke Networks’ DSX-5000 CableAnalyzer is Intertek (ETL) Veried in accordance with the IEC 61935-1
specications for accuracy Level IIIe, IV, and Level V, and in accordance with the ANSI/TIA-1152
specications for Level IIIe.
• Versiv™ modular design supports copper certication, ber loss, and OTDR testing
• Taptive™ user interface simplies set-up, and eliminates errors
• Manage and track testers, setups and results, and generate reports with LinkWare PC and
Linkware Live
• Endorsed by more than 28 cabling manufacturers worldwide
• Alien Crosstalk testing capability included
Model Description Gold 1YR Gold 3YR
DSX-5000 DSX-5000 CableAnalyzer Kit for Copper Cabling Certication GLD-DSX-5000 GLD3-DSX-5000
DSX-5000 120/GLD
Kit bundled with 1 year of Gold Support coverage (available in the United
States, Europe and Japan only. Europe order: DSX-5000 INTL/GLD, Japan
order: DSX-5000 AP/GLD)
Included in Bundle
DSX-5000-PRO
Versiv Professional Kit contains the DSX CableAnalyzer, CertiFiber
Pro, OptiFiber Pro, Fiber Inspection and a full complement of product
accessories.*
GLD-DSX-5000-PRO GLD3-DSX-5000-PRO
DSX-5000-PRO/GLD
DSX-5000-PRO with 1 year Gold Support coverage (available in United
States, Europe and Japan only. Europe order DSX-5000PROINTLGLD,
Japan order: DSX-5000-PROAP/GLD).
Included in Bundle
DSX-5000Qi DSX-5000 CableAnalyzer with CertiFiber Pro Quad OLTS Modules, and USB
Video Inspection Probe for Copper and Fiber Loss certication GLD-DSX-5000Qi GLD3-DSX-5000Qi
DSX-5000Qi 120/GLD
Kit bundled with 1 year of Gold Support coverage (available in the United
States, Europe and Japan only. Europe order: DSX-5000QiINTL/GLD, Japan
order: DSX-5000Qi AP/GLD)
Included in Bundle
DSX-5000QOi
DSX-5000 CableAnalyzer with CertiFiber Pro Quad OLTS modules, OptiFiber
Pro Quad OTDR module and USB Fiber Inspection Video Probe for Copper,
Fiber Loss, and OTDR certication
GLD-DSX-5000QOi GLD3-DSX-5000QOi
DSX-5000QOi120/GLD
Kit bundled with 1 year of Gold Support coverage (available in the United
States, Europe and Japan only. Europe order: DSX-5000QOiINTLGLD, Japan
order: DSX-5000QOi AP/GLD)
Included in Bundle
DSX-5000Mi
DSX-5000 CableAnalyzer CertiFiber Pro Multimode MM OLTS Modules
and USB Video Inspection Probe for Copper and Multimode Fiber Loss
certication
GLD-DSX-5000Mi GLD3-DSX-5000Mi
DSX-5000Mi 120/GLD
Kit bundled with 1 year of Gold Support coverage (available in the United
States, Europe and Japan only. Europe order: DSX-5000MiINTL/GLD, Japan
order: DSX-5000Mi AP/GLD)
Included in Bundle
DSX-ADD-R 1 Versiv Remote, (2) DSX-5000 CableAnalyzer Modules, and accessories to
add DSX-5000 CableAnalyzer capability to an existing OptiFiber Pro GLD-DSX-ADD-R GLD3-DSX-ADD-R
DSX-CFP-Q-ADD-R
1 Versiv Remote, (2) DSX-5000 CableAnalyzer modules, (2) CertiFiber Pro
Quad OLTS Modules, and accessories to add DSX-5000 CableAnalyzer and
CertiFiber Pro capability to an existing OptiFiber Pro OTDR
GLD-DSX-CFP-Q-
ADD-R
GLD3-DSX-CFP-Q-
ADD-R
DSX-ADD (2) DSX-5000 CableAnalyzer Modules, and accessories to add DSX-5000
capability to an existing CertiFiber Pro OLTS GLD-DSX-ADD GLD3-DSX-ADD
*Detail list of contents on page 8
www.flukenetworks.com/copper
Copper Cable Test Solutions
1-800-283-5853 (US and Canada) • www.flukenetworks.com
6 7
Copper Cable Test Solutions
Copper Adapter and Accessories
Model Description
DSX-PLA001 DSX Universal Permanent Link Adapter
DSX-PLA004S DSX CAT 6A/Class EA Permanent Link Set
DSX-PLA011S DSX TERA CAT 7A/Class FA Permanent Link Set
DSX-CHA004S DSX CAT 6A/Class EA Channel Set
DSX-CHA011S DSX TERA Cat 7A/Class FA Channel Set
DSX-CHA012S DSX GG45 Class FA Channel Adapter Set
DSX-CHA021S DSX M12 4-Position Adapter Set
DSX-COAX DSX Coax Adapter Set
DSX-TERA-KIT DSX TERA CAT 7A/Class FA Permanent Link and
Channel Kit
DSX-5000 MOD 1 GHZ DSX-5000 Replacement Module
DSX-PC5ES DSX CAT5 Patch Cord Adapter Set
DSX-PC6S DSX CAT6 Patch Cord Adapter Set
DSX-PC6AS DSX CAT6A Patch Cord Adapter Set
VERSIV-M Versiv Main Replacement
VERSIV-RU Versiv Remote Replacement
VERSIV-TSET Versiv Headphones
VERSIV-BATTERY Versiv Battery
VERSIV-ACUN Versiv Charger
VERSIV-STRP Versiv Strap Kit
VERSIV-BACKPK-STRP Backpack strap for Versiv Large Case
VERSIV-CASE3 Versiv Hardsided Case
VERSIV-LG-CASE Versiv Large Carry Case
VERSIV-SM-CASE Versiv Small Carry Case
VERSIV-STND Versiv Demo Stand
LinkWare PC
LinkWare Cable Test Management Software:
Free download at:
www.ukenetworks.com/linkwarePC
LinkWare Live
Cloud-based service that lets you manage
certication jobs anytime, anywhere, with
anyone on any device
www.ukenetworks.com/linkwarelive
DTX-ACUN AC Charger Universal
DTX-ACNA AC Charger, North America
DTX-CASE Standard Carrying Case—DTX Series
DTX-STRP DTX carrying strap
DTX-LION Lithium Ion Battery Pack
DTX-COAX DTX Coax Cable Test Adapter (2 adapters
included)
DTX-PC5ES
DTX Patch Cord Test Adapter Set for Category
5e patch cords. Certies both shielded and
unshielded category 5e patch cords per
ANSI/TIA 568-C and ISO 11801:2010
DSX-PLA004S
DSX-PLA011S
DSX-CHA004S
DSX-CHA011S
VERSIV-BATTERY
VERSIV-STRP
DTX-PC5ES
DSX-PLA004S
VERSIV-TSET
RSIV
-
BATTERY
RSIV
-
TSET
DSX-
CHA0
04S
D
S
X-
C
HA
0
11
S
VERSIV-ACUN
VERS
IV-A
CUN
DTX-PC6S
DTX-
PC6S
Copper Adapter and Accessories cont.
Model Description
DTX-PC6S DTX Patch Cord Test Adapter Set for Category 6 patch cords. Certies both shielded and unshielded category 6 patch
cords per ANSI/TIA 568-C and ISO 11801:2010
DTX-PC6AS DTX Patch Cord Test Adapter Set for Category 6A patch cords. Certies both shielded and unshielded category 6A
patch cords per ISO 11801:2010
DTX-PCTAC5EKS Twin pack of shielded Cat 5e jacks. Recommended replacement for DTX-PC5ES Patch Cord Test adapters
DTX-PCTAC6KS Twin pack of shielded Cat 6 jacks. Recommended replacement for DTX-PC6S Patch Cord Test adapters
DTX-PCTAC6AKS Twin pack of shielded Cat 6A jacks. Recommended replacement for DTX-PC6AS Patch Cord Test adapters
DSP-PCI-C6JACK Replacement Cat 6 Jacks for the DSP-PCI-C6 Patch Cord Adapter, set of 10
DTX-PLA002 One Permanent Link Adapter for Cat 6A and Alien Cross Talk testing. This adapter can be used for all permanent link
tests Cat 6A/6/5e/5 and Cat 3
DTX-PLA002PRP DTX-PLA002 plug replacement parts. This item includes two contact blocks of the 8-pin modular plug.
DTX-PLA001 One Permanent Link Adapter for use with the DTX Series CableAnalyzer. This adapter is compatible with all
DSP-PMxx Personality Modules but it does not include a Personality Module
DTX-CHA002 Cat 6A/Class Ea Channel Adapter optimized for Alien Crosstalk measurements. This adapter can be used to test
Cat 6A/6/ 5e/5/3 and Class Ea/E/D and C channels
Personality Modules
DSP-PM19B SYSTIMAX® VisiPatch® 360 (T568B) Personality Module
DSP-PM19A SYSTIMAX VisiPatch 360 (T568A) Personality Module
DSP-PM17B TYCO/AMP 610XC Connector (T568B) Personality Module
DSP-PM17A TYCO/AMP 610XC Connector (T568A) Personality Module
DSP-PM16B LEVITON 110 (T568B) Personality Module
DSP-PM16A LEVITON 110 (T568A) Personality Module
DSP-PM15B ADC/KRONE Highband (T568B) Personality Module
DSP-PM15A ADC/KRONE ULTIM8 (T568B) Personality Module
DSP-PM14B ADC/KRONE ULTIM8 (T568B) Personality Module
DSP-PM14A ADC/KRONE ULTIM8 (T568A) Personality Module
DSP-PM13B SIEMON S210 (T568B) Personality Module
DSP-PM13A SIEMON S210 (T568A) Personality Module
DSP-PM12B PANDUIT GIGAPUNCH (T568B) Personality Module
DSP-PM11B Belden GigaBIX (T568B) Personality Module
DSP-PM11A Belden GigaBIX (T568A) Personality Module
DSP-PM10B SYSTIMAX 110 (T568B) Personality Module
DSP-PM10A SYSTIMAX 110 (T568A) Personality Module
NFA-LC Set of two LC Adapters for DTX-xFM2 power meter port
NFA-ST Set of two ST Adapters for DTX-xFM2 power meter port
NFA-FC FC Test Adapters, Set of two
NFB1/2-LC/ST A kit containing the Test Reference Cords sets NFK1-DPLX-LC, NFK1-DPLX-ST, NFK2-DPLX-LC, NFK2-DPLX-ST, LC and ST
adapters for the power meter and 62.5/125 and 50/125
NFK1-DPLX-SC Duplex MM 62.5 m TRC for SC Adapter, Set of 2
NFK1-DPLX-LC Duplex MM 62.5 m TRC for SC Adapter, Set of 2
NFK1-DPLX-ST Duplex MM 62.5 m TRC for SC Adapter, Set of 2
Copper Adapter and Accessories cont.
www.flukenetworks.com/copper
Copper Cable Test Solutions
1-800-283-5853 (US and Canada) • www.flukenetworks.com
8 9
Model Description
NFK1-DPLX-FC Duplex MM 62.5 m TRC for SC Adapter, Set of 2
NFK2-DPLX-SC Duplex MM 50 m TRC for SC Adapter, Set of 2
NFK2-DPLX-LC Duplex MM 50 m TRC for SC Adapter, Set of 2
NFK2-DPLX-ST Duplex MM 50 m TRC for SC Adapter, Set of 2
NFK2-DPLX-FC Duplex MM 50 m TRC for SC Adapter, Set of 2
NFK3-DPLX-SC Duplex SM TRC for SC Adapter, Set of 2
NFK3-DPLX-LC Duplex SM TRC for LC Adapter, Set of 2
NFK3-DPLX-ST Duplex SM TRC for ST Adapter, Set of 2
NFK3-DPLX-FC Duplex SM TRC for FC Adapter, Set of 2
NFK1-MANDREL-KIT Multimode Fiber Mandrel kit containing two red mandrels for 50/125 µm cable and two gray mandrels for
62.5/125 µm cable
NF-MANDREL-50 Multimode Fiber Mandrel for 50/125 µm cable
NF-MANDREL-625 Multimode Fiber Mandrel for 62.5/125 µm cable
NFC-Kit-Case Fiber Optic Cleaning Kit.
DTX-FBRCSE Carry case for DTX-xFM or DTX-xFM2 Fiber Loss Test Modules with storage space for Test Reference Cords and ber
connector adapters
To learn more visit: www.ukenetworks.com/dsx
Copper Cable Test Solutions
CableIQ™ Qualification Tester
CableIQ network cable qualication test tool is designed for network technicians who need to troubleshoot
connectivity problems and qualify cabling bandwidth. It detects speed and duplex settings of attached
switches and PCs. Intelligent wiremap graphically shows distance to faults (e.g.: pin 1 break at 37 ft).
Lightweight, rugged, reliable unit tests all copper cabling. Its ease and power helps you close trouble
tickets faster and ensure smooth upgrades to higher network speeds.
• Sees if your existing cabling can support voice, VoIP, 10/100/Gigabit Ethernet
• Troubleshoots why existing cabling plant can’t support the desired network bandwidth
• Discover what’s at the end of any cable and displays device conguration (speed/duplex/pairing)
• Frees up switch ports and identies unused links
• Graphically maps wiring conguration and shows distance to faults, graphical wire mapping, opens,
and shorts.
• Locates and traces cable with IntelliTone™ digital signaling technology
Model Description Gold 1YR Gold 3YRs
CIQ-100 CableIQ with remote adapter, soft carrying case and four AA
batteries GLD-CIQ GLD3-CIQ
CIQ-KIT
CableIQ main unit, eight remote adapters, Reporter software,
IntelliTone 200 Digital Probe, (2) RJ45-RJ45 patch cords, USB
cable, coax ‘F’ push-on adapter, 75-ohm coax patch cord, RJ45/11
universal coupler, RJ11-RJ11 patch cord, four AA batteries, and
hard carry case
GLD-CIQ GLD3-CIQ
CIQ-KRQ
CableIQ, RJ-45 patch cord (2), RJ-11 patch cord (2), bare wire
adapter, speaker wire adapter, coax cable, coax BNC adapter, coax
RCA adapter, “Qualied” labels (50) and a soft carrying case
GLD-CIQ GLD3-CIQ
CIQ-FTKSFP Copper and Fiber Technician’s Kit—includes the CableIQ (CIQ-KIT)
and SimpliFiber Pro (FTK1000) Fiber Test Kit. See Photo
GLD-CIQ
GLD-SFPRO
GLD3-CIQ
GLD3-SFPRO
Accessories
Model Description
MICRO-DIT Micro IT kit (CIQ + MicroScanner2) soft carry dufe
CIQ-COAX CableIQ Coax Adapter Kit—includes F-connector, BNC and RCA connectors
CIQ-IDK24 CableIQ Remote Identier Kit—includes remote identier numbers 2-4
CIQ-IDK57 CableIQ Remote Identier Kit—includes remote identier numbers 5-7
CIQ-RJA RJ-45/11 modular adapter
CIQ-SPKR CableIQ speaker wire adapter
CIQ-WM CableIQ main wiremap adapter (replacement part for lost or damaged unit)
CLIP-SET Clip Set – includes RJ-45-to-8-clip test lead
To learn more visit: www.flukenetworks.com/cableiq
CableIQ Advanced IT Kit
Copper Cable Test Solutions
www.flukenetworks.com/copper
Versiv Professional Kit includes:
Versiv mainframe and accessories: (2) Versiv Mainframes, (2) Headsets, (2) Hand Straps, (2)
Shoulder Straps, Hard sided Carry Case, (2) Large Dufe Bags, (2) Backpack straps for Versiv Dufe
Bag, (2) Versiv stands, USB Interface Cable, Versiv Open Source Software CD, (2) AC Chargers,
(2) Universal Couplers, Statement of Calibration, and Getting Started Guide
DSX CableAnalyzer: (2) DSX-5000 CableAnalyzer Modules, (2) AxTalk Terminators, Set of
CAT 6A/Class EA Permanent Link Adaptors, Set of CAT 6A/Class EA Channel Adaptors, Universal
Permanent Link Adaptors Set (accepts personality modules), DSX Series Coaxial Adapter Set, DSX
Patch Cord Test Adapter Set for Category 5e patch cords, DSX Patch Cord Test Adapter Set for
Category 6 patch cords, DSX Patch Cord Test Adapter Set for Category 6A patch cords, DSX M12
4-position Channel Adapter Set
CertiFiber Pro Quad OLTS: (2) CertiFiber Pro Quad OLTS Modules, (4) Sets of 50µm Multimode EF TRC
kits: SC/LC (2 SC/LC, 2 LC/LC) , SC/SC (4 SC/SC), SC/ST (2 SC/ST, 2 ST/ST), SC/FC (2 SC/FC,
2 FC/FC), 4 Sets of 62.5µm Multimode EF TRC kits: SC/LC (2 SC/LC, 2 LC/LC) , SC/SC (4 SC/SC),
SC/ST (2 SC/ST, 2 ST/ST), SC/FC (2 SC/FC, 2 FC/FC), 4 Sets of 9µm Singlemode TRC kits: SC/LC
(2 SC/LC, 2 LC/LC) , SC/SC (4 SC/SC), SC/ST (2 SC/ST, 2 ST/ST), SC/FC (2 SC/FC, 2 FC/FC), 4 TRC Carry
Cases, 4 Sets of Interchange Adapters (LC – installed on units, SC, ST and FC)
OptiFiber Pro Quad OTDR: OptiFiber Pro Quad OTDR Module, 50µm Multimode Launch Cords
(3 SC/LC, 3 SC/SC, 2 SC/ST, 2 SC/FC, 1 LC/LC, 1 ST/ST, 1 FC/FC), 62.5µm Multimode Launch Cords (1
SC/LC, 3 SC/SC, 2 SC/ST, 2 SC/FC), 9µm Singlemode Launch Cords (3 SC/LC, 3 SC/SC, 2 SC/ST,
2 SC/FC, 1 LC/LC, 1 ST/ST, 1 FC/FC, 2 SC/SCAPC, 2 SC/LCAPC), 50µm Multimode TRC OTDR port saver
(SC/SC, LC/LC), 62.5µm Multimode TRC OTDR port saver (SC/SC, LC/LC), 9µm Singlemode
TRC OTDR port saver (SC/SC, LC/LC), OTDR Source Port Interchange Adapter Sets (LC – installed
on unit, SC/ST, FC), (2) OTDR Hanging straps and magnets,
Fiber inspection and cleaning: (2) Versiv USB inspection cameras and tips sets, (2) OneClick
Cleaners (1.25 mm), (2) OneClick Cleaners (2.50 mm), Enhanced Fiber Optic Cleaning Kit with
OneClick cleaners
Versiv mainframe and accessories
DSX CableAnalyzer
OptiFiber Pro Quad OTDR
Fiber inspection and cleaning
CertiFiber Pro Quad OLTS
1-800-283-5853 (US and Canada) • www.flukenetworks.com
10 11
IntelliTone™ Pro 200 LAN Toner and Probe
The IntelliTone Pro 200 LAN Toner and Probe Series from Fluke Networks is the rst network cable
toner and probe to offer digital and analog signaling all in one tool. The IntelliTone Pro 200 LAN Toner and
Probe Series from Fluke Networks gives you superior vision for locating cables hidden in oors, ceilings,
walls, and in bundles. Its breakthrough digital technology makes it the rst tool to tone and trace safely
and effectively on active networks.
• Ends cable location confusion—decisively
rejects noise and false signals
• Locates cables on active networks—even when
terminated at a switch
• Isolates cable and wiring within a bundle de-
spite cable bleed
• Conrms cable location, veries continuity, and
detects faults (opens, shorts, and reversed pairs) in one step
SmartTone® analog toning technology:
• Isolates individual wire pairs precisely by changing tone when shorted
• Effectively traces and locates voice, audio, and video cabling
MicroMapper™
Simple verication tester veries wiremap and identies faults with LEDs.
•Testing of twisted pair cables for open circuits, shorts, crossed pairs, reversed pairs and split pairs
• Easy-to-read fault display
• Tone generator for tracing installed cables hidden in walls, oors and ceilings
• Remote unit enables one-person testing of installed cables
Model Description
MT-8200-49A MicroMapper and MicroMapper Remote, patch cable, 6-volt alkaline battery and user guide
To learn more visit: www.flukenetworks.com/micromapper
MicroScanner2 Cable Verifier
Next generation MicroScanner streamlines voice/data/
video cable and service testing. The user interface
makes testing fast, easy, and crystal clear. Everything
cable technicians need to know, including available
services (10/100/1000 Ethernet, POTS, PoE voltage),
cable length, wiremap, cable ID, and distance to fault all
are displayed on one oversized backlit screen. Replace
multiple tools by testing all RJ-11, RJ-45, and coax (F)
media with no adapters. Built-in IntelliTone™ digital
and analog toning precisely locates virtually any cable
or wire pair – even on active networks. Ergonomic design
features sleek rubber over mold to enhance grip and ruggedness. Includes carry case.
• Displays cable length, wiremap, cable ID, and distance to fault on one screen
• Detects today’s media services, including 10/100/1000 Ethernet, POTS, and PoE
• Locates virtually any cable or wire pair with IntelliTone digital and analog toning
www.flukenetworks.com/copper
Copper Cable Test Solutions
Copper Cable Test Solutions
Model Description
MS2-100 MicroScanner2 Cable Verier
MS2-KIT MicroScanner2 Professional Kit—includes MicroScanner2 Cable Verier, Remote ID #s 2-7, IntelliTone Pro 200 Probe,
bare wire adapter, coax cable, two shielded RJ-45 cables, two RJ-11 cables and a deluxe carry case
MS2-TTK
MicroScanner2 Termination Test Kit—includes MicroScanner2 Cable Verier, IS60 Pro Tool Kit, IntelliTone Pro 200
Probe, RJ-11 and RJ-45 patch cables, lanyard, owners CD and quick start guide, 9 volt battery and a deluxe
carry case
MS2-FTK Copper and Fiber Basic Technician’s Kit—includes the MicroScanner (MS2-100) and SimpliFiber Pro (FTK1000)
Fiber Test Kit
MS2-IDK27 MicroScanner2 Remote ID Kit #s 2-7
MT-8200-63A IntelliTone Pro 200 Probe
MS2-WM MicroScanner2 Main Wiremap Adapter
MICRO-DIT Mirco IT kit (CIQ + MircoSacnner2) soft carry dufe
Model Description
MT-8200-60-KIT IntelliTone Pro 200 LAN Toner and Pro 200 Probe, coax F connector adapter, (2) RJ11 and (2) RJ 45 patch cables, test
leads with alligator clips, lanyards, quick start guide, and (2) 9 volt batteries
MT-8200-61-TNR IntelliTone Pro 200 LAN Toner, coax F connector adapter, RJ11 and RJ 45 patch cables, test leads with alligator clips,
lanyard, quick start guide, and 9 volt battery
MT-8200-63A IntelliTone Pro 200 Probe, RJ11 and RJ 45 patch cables, lanyard, quick start guide, and 9 volt battery
MT-8202-05 IntelliTone Case Heavy-duty pack cloth padded and lined case with belt loops and d-ring
MT-8203-20 Test Leads with Bed of Nails: Set of two Banana Jack test leads with piercing pin ‘Bed of Nails’ alligator clips with
vinyl sleeves
MT-8203-22 Test Leads with Alligator Clips: Set of two Banana Jack test leads with standard alligator clips with vinyl sleeves
Pro3000™ Analog Tone and Probe
Pro3000 Analog Tone and Probe Kit tones and traces wire.
• Tone and trace wire on non-active networks
• SmartTone™ technology provides ve distinct tones for exact pair identication
• Sends loud tone up to 10 miles (16 kilometers) on most cables
• Loud speaker on Probe makes the tone easier to hear through drywall, wood, and other enclosures
• Angled bed-of-nails clips allow easy access to individual pairs
• RJ-11 connector is ideal for use on telephone jacks
• Attach nylon pouch (included in kit) to your belt for easy transport
Model Description
26000900 Pro3000 Analog Tone and Probe Kit
26100900 Pro3000 Analog Probe
26200900 Pro3000 Analog Tone Generator
26100103 Pro3000 Analog Probe replacement tip (two per bag)
To learn more visit: www.ukenetworks.com/microscanner
To learn more visit: www.ukenetworks.com/intellitone
To learn more visit: www.ukenetworks.com/pro3000
1-800-283-5853 (US and Canada) • www.flukenetworks.com
12 13
Pocket Toner®
The Pocket Toner® connects to any voice, data, or video cable to detect open/short circuits,
continuity, AC/DC voltage* and dial tone* all while protecting up to 52 volts. All of the Pocket Toners
have dual audible indicators in the main body and detachable buzzer toner units, removable push on
connectors, auto shut-off and easy-to-read indicators.
• Low-voltage circuit protection for both the unit and the detachable toner
• Dual audible indicators in the main body and detachable buzzer toner units
• Auto shut-off
• Easy-to-read indicators; removable push-on connectors
• Male and female adaptable toner section
• Lightweight, durable anodized aluminum body
Model Description
PTNX1
Identify and test low-voltage, singular coax cables for continuity, opens/shorts and 50-75 1
termination. Low-voltage protection up to 52 volts. Kit includes NX1 unit, toner, F-type
(M-push, Speed 81™) adapters and 1-AAA battery
PTNX2 All the features of the NX1 plus AC/DC voltage detection- all in an easy-to-read LCD. Kit includes
NX2 unit, toner, F-type (M-push, Speed 81) adapters and 1-AAA battery
PTNX2-DLX
All the NX2 features. Kit includes NX2 unit, toner, 66 block adapter, RJ-11 adapter, RJ-45
adapter, Dial Tone Detective™, alligator clips with RJ-45 adapter, F-type (F, 9-M-push, M-71,
Speed 81) adapters, RCA (M, F) adapters, BNC (M, F) adapters, 1-AAA battery and deluxe case
with belt clip
PTNX2-CABLE All the NX2 features. Kit includes NX2 unit, toner, alligator clips adapter, F-type
(F, M-push, M-71, Speed 81) adapters, 1-AAA battery and small canvas case
PTNX8 All the features of the NX1 and NX2 plus the ability to test up to 8 cables at once. NX8 unit,
toner, F-type (M-push, Speed 81) adapters, 1-AAA battery and deluxe case with belt clip
PTNX8-CABLE All the NX8 features. Kit includes NX8 unit, toner, 8 ID caps, alligator clips, F-type
(F, 9-M-push, M-71, Speed 81) adapters, 1-AAA battery and deluxe case w/ belt clip
PTNX8-CT
All the NX8 features. Kit includes NX8 unit, toner, 8 ID caps, 66 block adapter, RJ-11 adapter,
Dial Tone Detective, alligator clips with RJ-11 adapter, F-type (F, 9-M-push, M-71, Speed 81)
adapters, 1-AAA battery and deluxe case with belt clip
PTNX8-DLX
All the NX8 features. Kit includes NX8 unit, toner, 8 ID caps, 66 block adapter, RJ-11 adapter,
RJ-45 adapter, Dial Tone Detective, alligator clips with RJ-45 adapter, F-type (F, 9-M-push,
M-71, Speed 81) adapters, RCA (M, F) adapters, BNC (M, F) adapters, 1-AAA battery and deluxe
case w/ belt clip
PTNX8-VV-PRO
All the NX8 features. Kit includes NX8 unit, toner, 8 ID caps, 66 block adapter, 8-RJ-11 adapters,
RJ-45 adapter, Dial Tone Detective, alligator clips w/ RJ-11 adapter and RJ-45 adapter, F-type
(F, 9-M-push, M-71, Speed 81) adapters, RCA (M, F) adapters, BNC (M, F) adapters, 1-AAA bat-
tery and deluxe case w/ belt clip
ADAP-PTNX-KIT
Alligator clips and RJ-45 adapter, alligator clips and RJ-11 adapter, Dial Tone Detective,
RJ-11 adapter, 66 block adapter, RJ-45 adapter, F-type (F, M-Push, M-71, Speed 81)
connectors, RCA (M, F) connectors, BNC (M, F) connectors and 2-wire clip adapter
CASE-PTNX-SM Small case
CASE-PTNX-LG Large case
PTNX8-ID-1-8 8-ID caps
ADAP-PTNX-RJ11 8 RJ-11 adapters
ADAP-PTNX-RJ45 8 RJ-45 adapters
ADAP-PTNX-TNR 1 Toner
*Varies by model/kit conguration
To learn more visit: www.flukenetworks.com/pt
Cable
Professional
Satellite
Audio
& Video
LAN
Voice
Security
& Fire
Cable &
Telephone
www.flukenetworks.com/copper
Copper Cable Test Solutions
TS®100 PRO Cable Fault Finder
Invest in the right tool for all your technicians. The new TS100 PRO Cable Fault Finder with PowerBT™
Bridge Tap Detect is a telecom technician’s rst line of defense against bridge taps on a subscriber’s line.
Because a bridge tap is a signicant source of DSL network performance problems due to unwanted signal
reectance, it needs to be identied and xed quickly before the problem causes customer attrition. The
TS100 PRO can accurately locate multiple bridge taps in seconds on up to 3,200 feet of cable with the
touch of a button.
• Bridge tap detection for xDSL pre-qualication on
up to 3,200 feet (975 meters)
• Tests opens and shorts up to 8,000 feet
(2.4 kilometers)
• Sees past bridge taps to the end of the cable
• Patented SmartTone® tone generator with ve
different tones for exact pair identication
• Built-in TDR and toner
• AC/DC voltage detection and digital read out
Copper Cable Test Solutions
Model Description
TS100-PRO-BT-TDR TS100 PRO Cable Fault Finder TDR Kit with Bridge Tap Detect
LEAD-ABNP-100 Test lead with angled-bed-of-nails and piercing pin. Compatible with the TS100 and
TS100 PRO
CASE-TS100 TS100/TS100PRO pouch with Fluke Networks’ logo
LEAD-ALIG-100 Test lead with alligator clips. Compatible with the TS100 and TS100 PRO
LEAD-ABN-100 Test lead with angled-bed-of-nails. Compatible with the TS100 and TS100 PRO
To learn more visit: www.flukenetworks.com/ts100pro
15
1-800-283-5853 (US and Canada) • www.flukenetworks.com
14
LinkWare Live is a cloud-based service that lets you manage certification jobs
and tools anytime, anywhere, with anyone on any device.
• Keep track of every test on every job
• Define cable IDs and test settings
• Manage your testers and make sure they are up to date
• Upload your test results straight from the job site over Wi-Fi
• Track the usage and location of your testers
• Update software in the field
TS®90/TS®100 Cable Fault Finder
Fluke Networks’ cable fault nders are easy-to-use, three-in-one testers: a fault locator, a cable
inventory manager and a toner with SmartTone® technology. Easily nd the distance to opens or
shorts on electrical wire, telephone wire, security wire and coax. Displays distance reading rather
than waveform.
• TS90 works on any two or more conductor cable up to 2,500 feet
• TS100 works on any two or more conductor cable up to 3,000 feet (metric unit also available)
• Instantly measures distance to open or short from one end of any cable pair
• Patented SmartTone® tone generator positively identies pair
• Measures cable distance on spool
• Measures constantly while “on”
Model Description
26500000 TS100 Cable Fault Finder, BNC alligator clip
26500090 TS90 cable fault nder with BNC to alligator clips
26501100 TS90/TS100 line cord, BNC to alligator clip
26501160 TS90/TS100 pouch with belt clip
26501700 TS90/TS100 line cord, BNC to banana to ABN
To learn more visit: www.flukenetworks.com/ts90
To learn more visit: www.flukenetworks.com/ts100
Copper Cable Test Solutions
Certification Management
To learn more visit: www.ukenetworks.com/LinkWareLive
To sign up visit: www.linkwarelive.com
Technician can
download test setups
and cable IDs on the
tester in the field
Technician can
upload Test Results
from the job site
Project Manager
can track job
progress anytime
Asset Manager
can track last used location,
software version and
calibration status*
Project Manager
can setup the
tester remotely
in LinkWare Live
Reports Administrator
can download test results
from LinkWare Live
to LinkWare PC
*Feature available only in limited regions; to learn more visit:
www.fluknetworks.com/linkwarelive
4 of XXX
Customer Logo
Report for: Client Name
Project: Project Title
1
2
3
6
4
5
7
8
S
1
2
3
6
4
5
7
8
S
[Pair 12] 724F
[Pair 45] 1104F
[Pair 45] 37
[Pair 45] 37.0
[Pair 45] -19.2F
[Pair 45] 100.0
[Pair 45] 21.0
Worst Case Margin Worst Case Value
PASS MAIN SR MAIN SR
Worst Pair 12-36 36-78 12-36 36-78
11.0 11.4 1 1.0 11.4
78.5 93.3 78.5 93.3
34.0 32.8 34.0 32.8
Worst Pair 12 36 12 36
11.5 11.2 11.6 11.2
70.8 92.3 72.8 92.3
31.8 29.9 31.6 29.9
PASS MAIN SR MAIN SR
Worst Pair 12-36 12-36 12-78 78-12
14.4 15.0 17.1 17.5
36.3 36.3 96.5 96.5
27.4 27.4 18.9 18.9
Worst Pair 36 12 36 36
15.4 15.5 17.5 17.0
36.3 1.0 100.0 100.0
24.4 55.6 15.6 15.6
N/A MAINSRMAINSR
Worst Pair 12-36 36-78 12-45 12-45
-5.8 -6.0 -5.2 -5.6
78.5 93.5 92.0 100.0
15.7 12.6 12.9 11.3
Worst Pair 36 36 45 36
-3.7 -6.8 -2.7 -6.8
78.5 92.3 92.0 92.3
12.7 9.8 9.9 9.8
PASS MAIN SR MAIN SR
Worst Pair 78 36 78 36
2.5* 2.0* 2.5 5.5
1.1 1.1 1.1 86.8
19.0 19.0 19.0 12.6
Cable ID:
Date/Time: 09/01/2015 01:31:50 PM
Headroom:
Test Limit:
Cable Type:
Calibration Date: 10/15/2014
Operator:
Software Version: V4.3 Build 6
Limits Version: V4.3
NVP: 69.0%
Model: DSX-5000
Main S/N: 2906257
Remote S/N: 2906245
Main Adapter:
Remote Adapter:
RL @ Remote (dB)
MHz
0
10
20
30
40
50
60
0 75 150 225 300
ACR-N @ Remote (dB)
MHz
-80
-40
0
40
80
0 75 150 225 300
ACR-F @ Remote (dB)
MHz
0
20
40
60
80
100
075150225300
NEXT @ Remote (dB)
MHz
0
20
40
60
80
100
0 75 150 225 300
Insertion Loss (dB)
MHz
0
20
40
60
80
1
00
075150225300
RL (dB)
MHz
0
10
20
30
40
50
60
075150225300
ACR-N (dB)
MHz
-80
-40
0
40
80
0 75 150 225 300
ACR-F (dB)
MHz
0
20
40
60
80
100
0 75 150 225 300
NEXT (dB)
MHz
0
20
40
60
80
100
0 75 150 225 300
724 ft
2 of XXX
Customer Logo
Report for: Client Name
Project: Project Title
Cable ID Summary Test Limit Length Headroom Date / Time
724 ft 09/01/2015 01:31 PM
725 ft 09/01/2015 01:33 PM
234 ft
234 ft
271 ft
201 ft
201 ft
75 ft
213 ft
62 ft
69 ft
79 ft
83 ft
24 ft
102 ft
103 ft
PC 2 161 ft
63 ft
79 ft
67 ft
84 ft
117 ft
134 ft
112 ft
27 ft
58 ft
101 ft 09/15/2015 01:45 PM
66 ft 09/16/2015 01:10 PM
1 of XXX
LinkWare Live Version X.X
Product Module Serial Number Firmware Version Calibration Date
DSX- 5000 2405214 V4.3 Build 6 09/01/2016
DSX- 5000 2420168 V4.3 Build 6 09/01/2016
DSX- 5000 2420146 V4.3 Build 6 09/01/2016
DSX- 5000 2420195 V4.3 Build 6 09/01/2016
DSX- 5000 2420133 V4.3 Build 6 09/01/2016
DSX- 5000 2420148 V4.3 Build 6 09/01/2016
DSX- 5000 2420139 V4.3 Build 6 09/01/2016
DSX- 5000 2420147 V4.3 Build 6 09/01/2016
Customer Logo
LinkWare Live
Report Generated Date
Exclusively for: Prepared by:
Customer Name Company Name
Project ID First Name & Last Name
Project Name Email
Project Address Address
City, State, Zipcode City, State, Zipcode
Structured Cable
Certification Report
A
L
L
T
E
S
T
S
T
A
N
D
A
R
D
S
H
A
V
E
B
E
E
N
M
E
T
[Pair 12] 724F
[Pair 45] 1104F
[Pair 45] 37
[Pair 45] 37.0
[Pair 45] -19.2F
[Pair 45] 100.0
[Pair 45] 21.0
Worst Case Margin Worst Case Value
PASS MAIN SR MAIN SR
Worst Pair 12-36 36-78 12-36 36-78
11.0 11.4 1 1.0 11.4
78.5 93.3 78.5 93.3
34.0 32.8 34.0 32.8
Worst Pair 12 36 12 36
11.5 11.2 11.6 11.2
70.8 92.3 72.8 92.3
31.8 29.9 31.6 29.9
PASS MAIN SR MAIN SR
Worst Pair 12-36 12-36 12-78 78-12
14.4 15.0 17.1 17.5
36.3 36.3 96.5 96.5
27.4 27.4 18.9 18.9
Worst Pair 36 12 36 36
15.4 15.5 17.5 17.0
36.3 1.0 100.0 100.0
24.4 55.6 15.6 15.6
N/A MAIN SR MAIN SR
Worst Pair 12-36 36-78 12-45 12-45
-5.8 -6.0 -5.2 -5.6
78.5 93.5 92.0 100.0
15.7 12.6 12.9 11.3
Worst Pair 36 36 45 36
-3.7 -6.8 -2.7 -6.8
78.5 92.3 92.0 92.3
12.7 9.8 9.9 9.8
PASS MAIN SR MAIN SR
Worst Pair 78 36 78 36
2.5* 2.0* 2.5 5.5
11 11 11 868
RL @ Remote (dB)
MHz
0
10
20
30
40
50
60
0 75 150 225 300
ACR-N @ Remote (dB)
MHz
-80
-40
0
40
80
0 75 150 225 300
ACR-F @ Remote (dB)
MHz
0
20
40
60
80
100
0 75 150 225 300
NEXT @ Remote (dB)
MHz
0
20
40
60
80
100
0 75 150 225 300
RL (dB)
MHz
0
10
20
30
40
50
60
0 75 150 225 300
ACR-N (dB)
MHz
-80
-40
0
40
80
0 75 150 225 300
ACR-F (dB)
MHz
0
20
40
60
80
100
0 75 150 225 300
NEXT (dB)
MHz
0
20
40
60
80
100
0 75 150 225 300
www.flukenetworks.com/copper
1-800-283-5853 (US and Canada) • www.flukenetworks.com
16 17
FIBER TESTING,
TROUBLESHOOTING
AND CERTIFICATION
Inspection and Cleaning Plant Characteristics and Troubleshooting OTDR (Tier 2)
Certication
FI-7000
FiberInspector™
Pro
FiberInspector™
Mini Video
Microscope
Fiber Optic
Cleaning Kits
SimpliFiber® Pro
Optical Power
Meter and Fiber
Test Kits
CertiFiber® Pro
OLTS
MultiFiber™ Pro
MPO Power
Meter and Fiber
Test Kits
VisiFault™ Visual
Fault Locator
FindFiber™
Remote ID Fiber QuickMap™Fiber OneShot™
Pro
OptiFIber® Pro
OTDR
Fiber end-face certication
Check for ber end-face contamination or damage
Clean contamination
Check connectivity
Check polarity
Verify Loss over entire link to ensure loss budget not
exceeded
Encircled Flux compliant
Dual-ber loss testing
MPO ber loss testing
Basic (Tier 1)
Locate faults
Extended (Tier 2)
Pass/fail results
Document test results
LinkWare Live compatibility
Fiber types supported
Singlemode
Multimode
MPO
Singlemode
Multimode
Singlemode
Multimode
MPO
Singlemode
Multimode
Singlemode
Multimode
Singlemode MPO
Multimode MPO
Singlemode
Multimode
Singlemode
Multimode Multimode Singlemode Singlemode
Multimode
Source type LED LED LED, FP Laser LED, FP Laser LED, FP Laser Laser Laser Laser Laser LED, FP Laser
www.flukenetworks.com/fiber
Fiber Product Comparison
Fiber Product Comparison
Loss Length
(Tier 1) Certication
Loss Length
(Tier 1) Certication
1-800-283-5853 (US and Canada) • www.flukenetworks.com
18 19
OptiFiber® Pro OTDR
OptiFiber Pro OTDR is the industry’s rst data center OTDR built from the ground up to meet the
challenges of enterprise ber infrastructures. This ber troubleshooting and certication tool combines
uncomplicated power with unparalleled efciency and the exact functions needed for troubleshooting
or certifying campus, data center and storage ber networks.
It elevates ber testing with the industry’s only smartphone interface that turns any technician
into a ber expert. The DataCenter conguration eliminates uncertainty and errors that occur when
testing data center ber. Its ultra-short dead zones enable testing of ber patch cords in virtualized data
centers. These capabilities, plus the fastest-in-the-industry trace times, make the OptiFiber Pro OTDR the
must-have tool.
SmartLoop OTDR enables automated testing and analysis of two bers in a single test. This patent pending
process automatically separates the two bers for individual pass/fail analysis, display, and reporting. Not
only does this cut the testing time by at least half, it also enables bi-directional averaged OTDR testing of
two bers from one end.
• Effectively test data center ber with the least set-up and trace time
• Accelerate ber certication with trace times as short as two seconds in Quick Test mode
• Troubleshoot data center ber links where short patch cables and dense connectors are common
• SmartLoop OTDR introduces the testing of two bers in a single test eliminating the need to travel to
the far end of the connection to perform tests
• Reduce network downtime by quickly and precisely identifying faults on singlemode (SM) or
multimode (MM) ber
• Manage and track testers, setups and results, and generate reports with LinkWare PC and
Linkware Live
Model Description Gold 1YR Gold 3YR
OFP-100-M OptiFiber Pro Multimode OTDR for troubleshooting and extended
certication GLD-OFP-100-M GLD3-OFP-100-M
OFP-100-M/GLD Kit bundled with 1-year of Gold Support (available in U.S. only) Included in Bundle
OFP-100-S OptiFiber Pro Singlemode OTDR for troubleshooting and extended
certication GLD-OFP-100-S GLD3-OFP-100-S
OFP-100-S/GLD Kit bundled with 1-year of Gold Support (available in U.S. only) Included in Bundle
OFP-100-Q OptiFiber Pro Quad OTDR for troubleshooting and extended
certication GLD-OFP-100-Q GLD3-OFP-100-Q
OFP-100-Q/GLD Kit bundled with 1-year of Gold Support (available in U.S. only) Included in Bundle
OFP-100-Mi OptiFiber Pro Multimode OTDR for troubleshooting and extended
certication, includes FI-1000-KIT and accessories GLD-OFP-100-Mi GLD3-OFP-100-Mi
OFP-100-Mi/GLD Kit bundled with 1-year of Gold Support (available in U.S. only) Included in Bundle
OFP-100-Si OptiFiber Pro Singlemode OTDR for troubleshooting and extended
certication, includes FI-1000-KIT and accessories GLD-OFP-100-Si GLD3-OFP-100-Si
OFP-100-Si/GLD Kit bundled with 1-year of Gold Support (available in U.S. only) Included in Bundle
OFP-100-Qi OptiFiber Pro Quad OTDR for troubleshooting and extended
certication, includes FI-1000-KIT and accessories GLD-OFP-100-Qi GLD3-OFP-100-Qi
OFP-100-Qi/GLD Kit bundled with 1-year of Gold Support (available in U.S. only) Included in Bundle
OFP-CFP-Mi OptiFiber Pro and CertiFiber Pro Multimode testing kit GLD-OFP-CFP-Mi GLD3-OFP-CFP-Mi
OFP-CFP-Si OptiFiber Pro and CertiFiber Pro Singlemode testing kit GLD-OFP-CFP-Si GLD3-OFP-CFP-Si
OFP-CFP-Qi OptiFiber Pro and CertiFiber Pro Quad testing kit GLD-OFP-CFP-Qi GLD3-OFP-CFP-Qi
OFP-Q-ADD
OptiFiber Pro Add-on Kit—includes OptiFiber Pro Quad OTDR Module,
(2) SC/LC Multimode Launch Cables—50 µm, (2) SC/LC Singlemode
Launch Cable—9 µm, (2) OTDR source port interchangeable LC adapt-
ers, SC/SC Simplex Adaptor, LC/LC Simplex Adaptor, (2) Launch Fiber
Hanging straps and magnets, Carry Case, Statement of
Calibration and Getting Started Guide
GLD-OFP-Q-ADD GLD3-OFP-Q-ADD
Launch Fibers
Model Description
MMC-50-SCSC Multimode launch cable 50 µm SC/SC
MMC-50-SCLC Multimode launch cable 50 µm SC/LC
MMC-50-SCST Multimode launch cable 50 µm SC/ST
MMC-50-SCFC Multimode launch cable 50 µm SC/FC
SMC-9-SCSC Singlemode launch cable 9 µm SC/SC
SMC-9-SCLC Singlemode launch cable 9 µm SC/LC
SMC-9-SCST Singlemode launch cable 9 µm SC/ST
SMC-9-SCFC Singlemode launch cable 9 µm SC/FC
www.flukenetworks.com/fiber
Fiber Cable Test Solutions
Fiber Cable Test Solutions
To learn more visit: www.flukenetworks.com/optifiberpro
1-800-283-5853 (US and Canada) • www.flukenetworks.com
20 21
CertiFiber® Pro
CertiFiber Pro OLTS improves the efciency of ber certication with a 3-second, two-bers-at-both- wave-
lengths test. The Taptive user interface simplies set-up, eliminates errors and speeds troubleshooting.
A set reference wizard ensures correct reference setting and eliminates negative loss errors. Built on the
future-ready Versiv platform, CertiFiber Pro provides merged Tier 1 (Basic) / Tier 2 (Extended) testing and
reporting when paired with OptiFiber Pro module. A convenient quad module supports both singlemode
and multimode and is multimode Encircled Flux compliant. Manage and track testers, setups and results,
and generate reports with LinkWare PC and Linkware Live.
CertiFiber Pro’s double ended ber optic inspection capability allows you to inspect and certify ber optic
connector end-faces at both ends of your ber link in less than a second so you can get your job done the
rst time. This double ended ber optic inspection capability provides automated PASS/FAIL certication,
takes the guess work out of ber inspection so anyone can be a ber expert.
• Taptive™ user interface provides simple, animated guidance to eliminate incorrect reference setup and
“negative loss” errors
• Fastest time to certify—two bers at two wavelengths in three seconds
• Encircled Flux compliant as required by ANSI/TIA and ISO/IEC
• Double ended Pass/Fail certication of ber optic connector endfaces
• Merged Tier 1 (Basic) / Tier 2 (Extended) testing and reporting when paired with OptiFiber Pro
• ProjX™ management system ensures all jobs are completed correctly and efciently
• Convenient quad module supports both multimode and singlemode loss testing
• Extended singlemode distance range to 130 km
• Built-in Visual Fault Locator
Model Description Gold 1YR Gold 3YR
CFP-100-Q CertiFiber Pro Quad Testing Kit GLD-CFP-100-Q GLD3-CFP-100-Q
CFP-100-M CertiFiber Pro Multimode Testing Kit GLD-CFP-100-M GLD3-CFP-100-M
CFP-100-S CertiFiber Pro Singlemode Testing Kit GLD-CFP-100-S GLD3-CFP-100-S
OFP-CFP-Qi OptiFiber Pro and CertiFiber Pro Quad Testing Kit GLD-CFP-100-Qi GLD3-CFP-100-Qi
OFP-CFP-Mi OptiFiber Pro and CertiFiber Pro Multimode Testing Kit GLD-CFP-100-Mi GLD3-CFP-100-Mi
OFP-CFP-Si OptiFiber Pro and CertiFiber Pro Singlemode Testing Kit GLD-CFP-100-Si GLD3-CFP-100-Si
CFP-Q-ADD-R CertiFiber Pro Quad Add-on Kit with Remote GLD-CFP-Q-ADD-R GLD3-CFP-Q-
ADD-R
CFP-Q-ADD CertiFiber Pro Quad Add-on Kit GLD-CFP-Q-ADD GLD3-CFP-Q-ADD
CFP-MM-ADD CertiFiber Pro Multimode Add-on Kit GLD-CFP-MM-ADD GLD3-CFP-MM-ADD
CFP-SM-ADD CertiFiber Pro Singlemode Add-on Kit GLD-CFP-SM-ADD GLD3-CFP-SM-ADD
Model Description Gold 1YR
CFP-100-Si
CertiFiber Pro Singlemode OLTS with double ended inspection. This kit includes (2) Versiv
Mainframes, (2) CertiFiber Pro Singlemode OLTS Modules, (2) USB ber inspection video probes
each with 4 tips, Singlemode test reference cord kit (2m) for testing 9um LC terminated bers (2
SC/LC, 2 LC/LC), TRC Carrying Case, (2) 1.25 mm IBC OneClick Cleaners, (2) 2.5 mm IBC OneClick
Cleaners, (2) LC/LC Adaptors, (2) Hand Straps, (2) Shoulder Straps, Carry Case, USB Interface
Cable, Versiv Open Source Software CD, (2) AC Chargers, Statement of Calibration and Getting
Started Guide.
GLD-CFP-100-Si
CFP-100-Mi
CertiFiber Pro Multimode OLTS with double ended inspection. This kit includes (2) Versiv Main-
frames, (2) CertiFiber Pro Multimode OLTS Modules, (2) USB ber inspection video probes each
with 4 tips, Multimode Encircled Flux compliant test reference cord kit (2m) for testing 50um
LC terminated bers (2 SC/LC, 2 LC/LC), TRC Carrying Case, (2) 1.25 mm IBC OneClick Cleaners,
(2) 2.5 mm IBC OneClick Cleaners, (2) LC/LC Adaptors, (2) Hand Straps, (2) Shoulder Straps,
Carry Case, USB Interface Cable, Versiv Open Source Software CD, (2) AC Chargers, Statement of
Calibration and Getting Started Guide.
GLD-CFP-100-Mi
CFP-100-Qi
CertiFiber Pro Quad OLTS with double ended inspection. This kit includes (2) Versiv Mainframes,
(2) CertiFiber Pro Quad OLTS Modules, (2) USB ber inspection video probes each with 4 tips,
Multimode Encircled Flux compliant test reference cord kit (2m) for testing 50um LC terminated
bers (2 SC/LC, 2 LC/LC), Singlemode test reference cord kit (2m) for testing 9um LC terminated
bers (2 SC/LC, 2 LC/LC), TRC Carrying Case, (2) 1.25 mm IBC OneClick Cleaners, (2) 2.5 mm IBC
OneClick Cleaners, (2) LC/LC Adaptors, (2) Hand Straps, (2) Shoulder Straps, Carry Case, USB
Interface Cable, Versiv Open Source Software CD, (2) AC Chargers, Statement of Calibration and
Getting Started Guide.
GLD-CFP-100-Qi
Accessories
Model Description
FI-1000-KIT FI-1000 USB Fiber Inspection Video Probe with selective bulkhead and video probe tips
FI-1000 FI-1000 USB Fiber Inspection Video Probe for Versiv platform
SRC-9-SCSC-KIT Singlemode test reference cord kit (2m) for testing 9 µm terminated bers (4 SC/SC)
SRC-9-SCLC-KIT Singlemode test reference cord kit (2m) for testing 9 µm terminated bers (2 SC/LC, 2 LC/LC)
SRC-9-SCFC-KIT Singlemode test reference cord kit (2m) for testing 9 µm terminated bers (2 SC/FC, 2 FC/FC)
SRC-9-SCST-KIT Singlemode test reference cord kit (2m) for testing 9 µm terminated bers (2 SC/ST, 2 ST/ST)
SRC-9-SCSCAPCKIT Singlemode TRC KIT 2m (2 SCUPC/SCAPC, 2 SCAPC/SCAPC)
SRC-9-SCLCAPCKIT Singlemode TRC KIT 2m (2 SCUPC/LCAPC, 2 LCAPC/LCAPC)
MRC-50EFC-SCLCKIT Multimode Encircled Flux compliant test reference cord kit (2m) for testing 50 µm LC terminated bers
(2 SC/LC, 2 LC/LC)
MRC-50EFC-SCSCKIT Multimode Encircled Flux compliant test reference cord kit (2m) for testing 50 µm SC terminated bers (4 SC/SC)
MRC-50EFC-SCSTKIT Multimode Encircled Flux compliant test reference cord kit (2m) for testing 50 µm ST terminated bers
(2 SC/ST, 2 ST/ST)
MRC-50EFC-SCFCKIT Multimode Encircled Flux compliant test reference cord kit (2m) for testing 50 µm FC terminated bers
(2 SC/FC, 2 FC/FC)
MRC-50-EFC-SCSC Multimode Encircled Flux compliant test reference cord (2m) for testing 50um SC terminated bers (SC/SC)
MRC-50-EFC-SCLC Multimode Encircled Flux compliant test reference cord (2m) for testing 50um LC terminated bers (SC/LC)
SRC-9-SCSC Singlemode test reference cord (2m) for testing SC terminated bers (SC/SC)
SRC-9-SCLC Singlemode test reference cord (2m) for testing LC terminated bers (SC/LC)
Fiber Cable Test Solutions
Fiber Cable Test Solutions
www.flukenetworks.com/fiber
To learn more visit: www.flukenetworks.com/certifiberpro
1-800-283-5853 (US and Canada) • www.flukenetworks.com
22 23
MultiFiber™ Pro
MultiFiber Pro is the rst MPO ber tester to support both Singlemode and Multimode MPO ber
certication. MultiFiber Pro takes the complexity out of testing MPO trunks for loss and polarity.
With an on-board MPO connector, it is the rst tester to automate the MPO ber-trunk testing process
without using a fan-out cord. The power meter/light source boasts industry-rst functions such as
automatic scanning of all twelve bers and display of test results in an easy-to-read bar graph. These
innovative features allow MultiFiber Pro kits to eliminate the complexity of testing MPO trunks, making it
90 percent faster than the traditional simplex ber test methods.
• Automatic scanning and testing of all bers in MPO connectors with “Scan All”
• Support for both Multimode and Singlemode MPO trunks
• Eliminates the need for fan-out cords when testing ber trunks
• Easy-to-interpret test results with minimal navigation
• User interface displays all 12 bers
• Automated 8, 10 and 12 ber measurements
• Troubleshoot MPO links and drill down to single ber test results
Model Description Gold 1YR Gold 3YR
MFTK1200 MultiFiber Pro Multimode Testing Kit GLD-MFTK GLD3-MFTK
MFTK-SM1310 MultiFiber Pro 1310 nm Singlemode Kit GLD-MFTK-SM GLD3-MFTK-SM
MFTK-SM1550 MultiFiber Pro 1550 nm Singlemode Kit GLD-MFTK-SM GLD3-MFTK-SM
MFTK-MM850-SM1310 MultiFiber Pro Multimode and 1310 nm Singlemode Kit GLD-MFTK-MMSM GLD3-MFTK-MMSM
MFTK-MM850-SM1550 MultiFiber Pro Multimode and 1550 nm Singlemode Kit GLD-MFTK-MMSM GLD3-MFTK-MMSM
MFTK-SM1310-SM1550 MultiFIber Pro 1310 and 1550 nm Singlemode Kit GLD-MFTK-1310-SM1550 GLD3-MFTK-1310-SM1550
OFPMI-MFP OptiFiber Pro and MultiFiber Pro Multimode Testing Kit GLD-OFPMI-MFP GLD3-OFPMI-MFP
OFPQI-MFP OptiFiber Pro Quad and MultiFiber Pro Multimode Testing Kit GLD-OFPQI-MFP GLD3-OFPQI-MFP
Accessories
Model Description Gold 1YR Gold 3YR
MFPOWERMETER MultiFiber Pro Optical Power Meter GLD-MF GLD3-MF
MFMULTIMODESOURCE MultiFiber Pro Multimode 850 LED light source GLD-MF GLD3-MF
MF1310source MultiFiber Pro SM 1310 nm laser light source GLD-MF-SMS GLD3-MF-SMS
MF1550source MultiFiber Pro SM 1550 nm laser light source GLD-MF-SMS GLD3-MF-SMS
FI-7000-MPO FiberInspector Pro with MPO and cleaning GLD-FI-7000-MPO GLD3-FI-7000-MPO
TRC-MPO-PP-B 1 m MM TRC, MPO/MPO, Pinned/Pinned, Type B polarity
TRC-MPO-UP-B 1 m MM TRC, MPO/MPO, Unpinned/Pinned, Type B polarity
TRC-MPO-UU-B 0.3 m MM TRC, MPO/MPO, Unpinned/Unpinned, Type B polarity
TRC-SM-MPOAPC-PP-A 1 m SM TRC, MPOAPC/MPOAPC, Pinned/Pinned, Type A polarity
TRC-SM-MPOAPC-UP-A 1 m SM TRC, MPOAPC/MPOAPC, Unpinned/Pinned, Type A polarity
TRC-SM-MPOAPC-UU-A 0.3 m SM TRC, MPOAPC/MPOAPC, Unpinned/Unpinned, Type A polarity
BKC-MPO-ULC 1 m Breakout Cord for MM MPO Unpinned LC connector
BKC-MPO-USC 1 m Breakout Cord for MM MPO Unpinned SC connector
SBKC-MPOAPCU-LCAPC 1 m Breakout Cord for SM MPOAPC Unpinned LCAPC Connector
SBKC-MPOAPCU-SCAPC 1 m Breakout Cord for SM MPOAPC Unpinned SCAPC Connector
ADP-MPO-A Type A polarity MPO adapter for SM APC
ADP-MPO-B Type B polarity MPO adapter
www.flukenetworks.com/fiber
FI-7000 FiberInspector™ Pro
End-face contamination is a leading cause of ber failures. Dirt and contaminants cause insertion loss and
back-reection that inhibits optical transmission and causes havoc with transceivers. Fiber loss and OTDR
testing can expose this problem, but in many cases, dirty connections make ber testing time consuming
and inaccurate.
Since dirt can be an issue before, during, or after ber optic certication testing, and migrate from one
end-face to another upon mating, both sides of any connection must always be cleaned and inspected.
Further, mating contaminated connectors can cause permanent damage as microscopic debris is crushed
between end-faces in physical contact. Even factory terminated patch cords or pigtails must be inspected
as protective caps do not keep ber optic connector end-faces clean. Avoiding this common cause of
failure, starts with inspecting the ber optic connector end-face and eliminating any contamination
before insertion into a bulkhead or piece of equipment.
The FI-7000 FiberInspector Pro is a ber optic inspection scope that allows you to inspect and certify
end-faces in 2 seconds so you can get the job done the rst time. This ber optic inspection scope
provides automated PASS/FAIL certication taking the guess work out of ber inspection so anyone can
be a ber expert.
• Automated Pass/Fail certication of ber optic connector end-faces
• Graphical indication of problem areas due to contamination, pits, chips, and scratches
• Certify to industry standards—IEC 61300-3-35
• Eliminate human subjectivity from end-face measurements
Model Description Gold 1YR Gold 3YR
FI-7000 FiberInspector Pro GLD-FI-7000 GLD3-FI-7000
FI-7000-MPO FiberInspector Pro w/MPO and cleaning GLD-FI-7000-MPO GLD3-FI-7000-MPO
FI-1000-KIT FI-1000 USB Fiber Inspection Video Probe with selective bulkhead and
video probe tips GLD-FI GLD3-FI
FI-1000 FI-1000 USB Fiber Inspection Video Probe for Versiv platform GLD-FI GLD3-FI
Accessories
Model Description
FI1000-SCFC-TIP SC and FC bulkhead video probe tip
FI1000-LC-TIP LC bulkhead video probe tip
FI1000-ST-TIP ST bulkhead video probe tip
FI1000-MU-TIP MU bulkhead video probe tip
FI1000-E2KAPC-TIP E2000/APC bulkhead video probe tip
FI1000-SCAPC-TIP SC/APC bulkhead video probe tip
FI1000-E2K-TIP E2000 bulkhead video probe tip
FI1000-LCAPC-TIP LC/APC bulkhead video probe tip
FI1000-2.5-UTIP 2.5 mm universal video probe tip for patch cords
FI1000-1.25-UTIP 1.25 mm universal video probe tip for patch cords
FI1000-2.5APC-UTIP 2.5 mm APC universal video probe tip for patch cords
FI1000-MPO-UTIP MPO probe tip and translator knob for patch cords and bulkheads
FI1000-MPOAPC-UTIP MPO/APC probe tip and translator knob for patch cords and bulkheads
FI1000-1.25APC-TIP 1.25 mm APC universal video probe tip for patch cords
FI1000-MPOAPC-RT MPO/MTP APC replacement tip with no translator knob
FI1000-MPO-RT MPO/MTP replacement tip with no translator knob
Fiber Testing, Troubleshooting and Certification
Fiber Testing, Troubleshooting and Certification
To learn more visit: www.ukenetworks.com/-7000 To learn more visit: www.ukenetworks.com/multiberpro
1-800-283-5853 (US and Canada) • www.flukenetworks.com
24 25
SimpliFiber® Pro Optical Power Meter
SimpliFiber Pro Optical Power Meter and Fiber Test Kits are the single “go-to” kits for anyone involved in
rst-line optical ber cabling installation and verication. Designed for in-house ber technicians as well
as contractors, our expertly congured kits are housed in a professional and durable case and contain all
the simple-to-use tools needed to quickly measure loss and power levels, locate faults and polarity issues,
and inspect and clean connector end-faces.
• Dual-wavelength testing—complete testing in half
the time
• Additional wavelengths to include 1490 and 1625—
calibrated to extend from typical enterprise wave-
lengths for other applications
• Min/Max—precision tracking of intermittent power
uctuations, a superior alternative to the inaccurate
“wiggle” test
• CheckActive™—audible tone and display icon alerts
you to a live ber
• Saves 1,000 results—compatible with our popular LinkWare™ Cable Test
Management Software
Model Description Gold 1YR
SFPOWERMETER SimpliFiber Pro optical power meter; SC adapter included. GLD-SFPRO
SFMULTIMODESOURCE
SimpliFiber Pro multimode 850/1300 light source. Fixed SC port (with ST and LC testing capa-
bility available using hybrid test-reference cord accessories purchased separately)—
includes FindFiber™ source capability.
GLD-SFPRO
SFSINGLEMODESOURCE
SimpliFiber Pro singlemode 1310/1550 laser light source. Fixed SC port (with ST and LC testing
capability available using hybrid test-reference cord accessories purchased
separately)—includes FindFiber source capability.
GLD-SFPRO
SFSINGLEMODE2
SimpliFiber Pro singlemode 1490/1625 laser light source. Fixed SC port (with ST and
LC testing capability available using hybrid test-reference cord accessories purchased
separately)—includes FindFiberTM source capability.
GLD-SFPRO
Fiber Test Kits
SimpliFiber Pro ber test kits come in every conguration to meet your testing needs. Each ber test kit
includes the following industry-leading features:
• Dual-wavelength testing—complete testing in half the time
• Additional wavelengths to include 1490 and 1625—calibrated to extend from typical enterprise wave-
lengths for broader applications
• Min/Max—precision tracking of intermittent power uctuations. A superior alternative to the
inaccurate “wiggle” test
• CheckActive—audible tone and display icon alerts you to a live ber
• Saves 1,000 results—fully compatible with our popular LinkWare™ Cable Test Management Software
• Quickly locate cable fault, polarity, and connector problems with VisiFault VFL
Complete Fiber Verication Kit (FTK1450)
The Complete Fiber Verication Kits are perfect for network technicians and contractors who install and
maintain premise networks with both multimode and singlemode optical ber. Use these kits to verify
optical loss and power levels at 850, 1300, 1310, 1550, and inspect ber end-faces, locate cable faults,
connector problems, and polarity issues.
Full-featured Inspection and Multimode Verication Kit (FTK1300 and FTK1350)
The Full-featured Inspection and Multimode Verication Kits are for network technicians and contractors
who install and maintain multimode premises network. Use these kits to verify optical loss and power
levels at 850 and 1300 nm, inspect ber end-faces, locate cable faults, connector problems, and
polarity issues.
Basic Verication Kit (FTK1000 and FTK2000)
The Basic Verication Kit is a great starter kit for network technicians and contractors who install and
maintain ber links. Available in single or multimode congurations, quickly verify optical loss and power
levels at 850 and 1300 nm or 1310 and 1550 nm. Add additional sources, microscopes, and VFL options
as needed.
Copper and Fiber Technician’s Kit (CIQ-FTKSFP)
Consisting of the CableIQ (CIQ-KIT) and the SimpliFiber Pro Basic Verication Kit (FTK1000), the Cop-
per and Fiber Technician’s Kit provides a robust combination of tools to help you expertly manage your
network to it keep it running smoothly and inexpensively. Simple-to-use straight from the box, you can do
everything from quickly troubleshooting and qualifying cabling link bandwidth to verifying optical ber
power and loss.
FTK2100 Singlemode Fiber Verication Kit
Includes SimpliFiber Pro optical power meter, two singlemode sources (1310/1550 and 1490/1625 nm),
carrying case, and SC power-meter adapter.
MS2-FTK Copper and Fiber Basic Technician’s Kit
Includes the MicroScanner2 (MS2-100) and SimpliFiber Pro (FTK1000) Fiber Test Kit.
Model FTK1000 FTK1300 FTK1350 FTK1450 FTK2000 FTK2100
SimpliFiber Pro Power Meter
SimpliFiber Pro Source
850/1300 MM source
SimpliFiber Pro Sources
1310/1550 SM source
SimpliFiber Pro Sources
1490/1625 SM source
FindFiber Remote ID source
FT120 200x FiberViewer
FT500 FiberInspector
VisiFault Visual Fault Locator
NFC-Kit-Box
(ber optic cleaning kit)
Professional durable carrying case
www.flukenetworks.com/fiber
Fiber Testing, Troubleshooting and Certification
Fiber Testing, Troubleshooting and Certification
To learn more visit: www.flukenetworks.com/simplifiberpro
1-800-283-5853 (US and Canada) • www.flukenetworks.com
26 27
Legacy Test Reference Cords, Adapters and Mandrels
Model Description
NF-MANDREL-50 Mandrel, 3 mm ber cable, 50 m (1)
NF-MANDREL-625 Mandrel, 3 mm ber cable, 62.5 m (1)
NFA-FC FC test adapters – set of two
NFA-LC LC test adapters – set of two
NFA-SC SC test adapters – set of two
NFA-ST ST test adapters – set of two
NFB1/2-LC/ST Kit of duplex MM 62.5 m and 50 m test cords with LC and ST adapters
NFK1-DPLX-FC Duplex MM 62.5 m test reference cords for FC adapter – set of two
NFK1-DPLX-LC Duplex MM 62.5 m test reference cords for LC adapter – set of two
NFK1-DPLX-SC Duplex MM 62.5 m test reference cords for SC adapter – set of two
NFK1-DPLX-ST Duplex MM 62.5 m test reference cords for ST adapter – set of two
NFK1-MANDREL-KIT Kit, mandrel, 3 mm ber cable, 50 m and 62.5 m
NFK2-DPLX-FC Duplex MM 50 m test reference cords for FC adapter – set of two
NFK2-DPLX-LC Duplex MM 50 m test reference cords for LC adapter – set of two
NFK2-DPLX-SC Duplex MM 50 m test reference cords for SC adapter – set of two
NFK2-DPLX-ST Duplex MM 50 m test reference cords for ST adapter – set of two
NFK3-DPLX-FC Duplex SM test reference cords for FC adapter – set of two
NFK3-DPLX-LC Duplex SM test reference cords for LC adapter – set of two
NFK3-DPLX-SC Duplex SM test reference cords for SC adapter – set of two
NFK3-DPLX-ST Duplex SM test reference cords for ST adapter – set of two
NFK1-SMPLX-SC Simplex MM 62.5 µm test reference cords for SC adapter – set of two
NFK1-SMPLX-LC Simplex MM 62.5 µm test reference cords for LC adapter – set of two
NFK1-SMPLX-ST Simplex MM 62.5 µm test reference cords for ST adapter – set of two
NFK2-SMPLX-SC Simplex MM 50 µm test reference cords for SC adapter – set of two
NFK2-SMPLX-LC Simplex MM 50 µm test reference cords for LC adapter – set of two
NFK2-SMPLX-ST Simplex MM 50 µm test reference cords for ST adapter – set of two
NFK3-SMPLX-SC Simplex SM test reference cords for SC adapter – set of two
NFK3-SMPLX-LC Simplex SM test reference cords for LC adapter – set of two
NFK3-SMPLX-ST Simplex SM test reference cords for ST adapter – set of two
Fiber QuickMap™ - Multimode Fiber Length and Distance to Fault
Fiber QuickMap quickly and efciently locates connections and breaks in multimode ber with the press
of one-button. By instantly (six second typical test time) providing distances to failures such as high-loss
and high-reectance incidents, it is the must-have troubleshooter for any technician who works with ber
in datacenters or campuses.
Locating faults like high loss connections or bad splices often requires a more expensive and complex
Optical Time Domain Reectometer (OTDR). The detail, documentation, certication and ease of use
provided by a Fluke Networks OTDR is exceptional, but is not always required for basic tests. Fiber Quick
Map uses reections to determine where db losses are occurring in just a few seconds, and lls the gap
between a Visual Fault Locator (VFL) and OTDR.
• Quick set-up. Connect your ber and press the Test button. No lengthy set-up necessary
• Find problems quickly. Six-second test time—no more blind troubleshooting that can waste hours
• Locate high loss incidents or breaks—nd the most common causes of ber failure
• See Key information on a large display; loss in db and distance in meters or feet
• Visible in dark areas. Backlighted display turns off automatically
• Tests 50/125µm and 62.5/125µm multimode ber up to 1,500 meters / 4,921 feet
• Removable SC adapter is easily cleaned
• Long battery life, 1,500 tests (typical) from 2 AA alkaline batteries
• Rugged construction; vibration and drop tested to 1 meter
• For singlemode ber - Use Fiber OneShot PRO
www.flukenetworks.com/fiber
Model Description Gold 1YR
FQM-MAIN Fiber QuickMap mainframe with carrying pouch GLD-FQM
FQM-KIT Fiber QuickMap Kit with SC/LC 50 m Launch Fiber, Interchangeable LC Adapter and carrying pouch GLD-FQM
FTS900 Fiber QuickMap Kit with test reference cords (50 and 62.5 µm for both SC/SC and SC/LC), VisiFault
Visual Fault Locator and carrying case GLD-FQM
FTS1000 Fiber QuickMap Troubleshooter Kit with test reference cords (50 and 62.5 µm for both SC/SC and SC/
LC), VisiFault Visual Fault Locator, and SimpliFiber Pro power meter and multimode source and case GLD-FQM-FTK
FTS1100
Fiber QuickMap Troubleshooter Kit: Includes Fiber QuickMap, SC/SC and SC/LC (50 and 62.5 m)
hybrid test reference cords cords, VisiFault VFL, SimpliFiber Pro power meter and multimode source,
FT500 FiberInspector Mini video microscope, and carrying case. (Available in the US only)
GLD-FQM-FTK
*For launch bers and accessories please see page 19
Fiber Cable Test Solutions
Fiber Cable Test Solutions
To learn more visit: www.flukenetworks.com/fiberquickmap
1-800-283-5853 (US and Canada) • www.flukenetworks.com
28 29
FiberInspector™ Mini Video Microscope
The FiberInspector Mini Video
Microscope enables inspection
of end-faces on all types of installed
ber. The portable video microscope
projects a crisp, clear image of
microscopic debris and
end-face damage.
• The exceptionally convenient
FiberInspector Mini uses a 200x magnication probe sufcient for inspecting both multimode and
singlemode ber
• Quickly determines whether ber connectors on a hardware device are clean and in good condition
without disassembling the device
Accessories
Model Description
NFM110 Accessory tip set for FiberInspector Mini (LC, FC and 1.25 mm Universal)
NF390 Bulkhead APC (Angled Physical Connector) video adapter probe for FiberInspector Mini
NFM120 Rechargeable battery for FiberInspector Mini (NIMH)
To learn more visit: www.flukenetworks.com/fiberinspectormini
Fiber OneShot™ PRO - Singlemode Fiber Length and Distance to Fault
Fiber OneShot PRO takes the complexity out of singlemode ber testing by analyzing ber links and
measuring faults up to 23,000 meters (15 miles) in less than ve seconds. Whether you are troubleshooting
FTTx, Hybrid Fiber Coax (HFC), ber links between Central Ofces, or working on regional or rural access
networks, Fiber OneShot PRO is your rst response to ber trouble.
Locating faults like high loss connections, macro bends or breaks often requires a more expensive and
complex Optical Time Domain Reectometer (OTDR). The detail, documentation, certication and ease of
use provided by a Fluke Networks OTDR is exceptional, but is not always required for basic tests. Fiber One
Shot uses reections to determine where db losses are occurring in just a few seconds, and lls the gap
between a Visual Fault Locator (VFL) and OTDR.
• Quick set-up. Connect your ber and press the Test button. No lengthy set-up necessary
• Find problems quickly. Six-second test time—no more blind troubleshooting that can waste hours
• Locate macro bends, high-loss splices, breaks and dirty connectors in singlemode ber
• See Key information on a large display; power loss in db and distance in meters or feet
• Visible in dark areas. Backlighted display turns off automatically
• Tests 9/125µm singlemode ber up to 23,000 meters / 15 miles
• Save and store up to 99 test results for later review
• Removable SC adapter is easily cleaned
• Long battery life, 1,500 tests (typical) from 2 AA alkaline batteries
• Rugged construction; vibration and drop tested to 1 meter
• For multimode ber - Use Fiber QuickMap
Model Description Gold 1YR
FIBR-1-SHOTPRO Fiber OneShot PRO only—includes meter, SC adapter, 22-language quick reference guide
(QRG) on CD, manual and batteries GLD-FOS-PRO
FIBR-1-KITPRO Fiber OneShot PRO-SC-Kit—same as SHOTPRO plus UPC-UPC 2-meter patch cord, holster
and case GLD-FOS-PRO
FIBR-1-KITPRO-VF Fiber OneShot PRO-SC-Kit with VisiFault—everything in the PRO-SC-Kit plus the VisiFault Visual
Fault Locator with 2.5 mm universal adapter GLD-FOS-PRO
FIBR-1-KITPRO-VFPM
Fiber OneShot PRO-SC-Kit with VisiFault and SimpliFiber Pro—includes meter, SC adapter,
UPC-UPC 2-meter patch cord, holster, case, 22-language QRG on CD, manual and batteries plus
the VisiFault Visual Fault Locator with 2.5 mm universal adapter and SimpliFiber Pro optical
power meter and SC adapter
GLD-FOS-MULTIKITS
Accessories
Model Description
FIBR-AC-UAPC 1-meter UPC-APC patch cord
FIBR-UPC-CORD-2M 2-meter UPC-UPC patch cord
Model Description
FT120 FiberViewer, 200X
FT140 FiberViewer, 400X
NF350 1.25 mm Universal Microscope Adapter
Model Description Gold 1YR Gold 1YR
FT500
FiberInspector
Mini Video
Microscope
GLD-FTINSPECTOR GLD3-FTINSPECTOR
FT525
FiberInspector
Mini and
Cleaning Kit
GLD-FTINSPECTOR GLD3-FTINSPECTOR
Model Description
VisiFault VisiFault Visual Fault Locator with
2.5 mm Universal Adapter
NF380 1.25 mm Universal VisiFault Adapter
FiberViewer™ Fiber Microscope
The FiberViewer ber microscope ensures a
termination is clean and ready for optical
transmission. Inspect multimode and singlemode
ber end-faces, and protect your eyes with the
built-in safety lter.
• FT120 offers 200X magnication, FT140 offers
400X magnication
To learn more visit: www.flukenetworks.com/fiberviewer
VisiFault™ Visual Fault Locator
The laser-powered VisiFault™ Visual Fault Locator (VFL)
traces bers, veries continuity and polarity, and helps
nd breaks in cables, connectors and splices.
Continuous and ashing modes for easier identication.
Compatible with 2.5 mm and 1.25 mm connectors for
easy connection.
• Bright red visible laser light source, features continuous and ashing modes
• Accelerates end-to-end ber continuity checks
• Speeds ber tracing and identication
• Aids in location of ber faults including tight bends, breaks and bad connectors
To learn more visit: www.flukenetworks.com/visifault
Fiber Cable Test Solutions
Fiber Inspection and Cleaning
www.flukenetworks.com/fiber
To learn more visit: www.flukenetworks.com/theone
1-800-283-5853 (US and Canada) • www.flukenetworks.com
30 31
Fiber Optic Cleaning Kits
Contaminated end-faces are the #1 cause of ber link failure. Prevent this common problem with
Fluke Networks’ Fiber Optic Cleaning Kits and Components. These precision ber optic cleaning kits
and components allow effective removal of all contaminants from end-faces on both patch cords and
inside ports.
• Everything needed for precision cleaning of end-faces on both patch cords and inside ports
• Compact form factor options available. Specially formulated solvent dissolves contaminants,
neutralizes static charge and encapsulates particles for removal
• A range of wiper swabs enable decontamination of all styles of ber optic connections
• Use the convenient and rugged carrying case to store all of the cleaning components
Model Description
NFC-Kit-Case
Fiber Optic Cleaning Kit—includes cleaning cube with wipes, ten cards with sealed
cleaning zones, solvent pen, 2.5 mm port cleaning swabs and 1.25 mm port cleaning
swabs in a rugged carrying case
NFC-Kit-Box Fiber Optic Cleaning Kit—includes cleaning cube with wipes, ve cards with sealed
cleaning zones, solvent pen and 2.5 mm port cleaning swabs
NFC-Cube Cleaning cube with wipes—cleans up to 500 end-faces
NFC-Cards-5pack 5 cards with 12 sealed cleaning zones each—perfect for troubleshooting
NFC-SolventPen Special solvent dispensed from pen (9 g)
NFC-Swabs-1.25mm LC and MU port cleaning swabs (25 count)
NFC-Swabs-2.5mm SC, ST, 2.5 mm port cleaning swabs (50 count)
NFC-Case Carrying case for cleaning accessories
NFC-IBC-1.25mm OneClick cleaners for 1.25 mm LC and MU connector and patch cord (5 qty)
NFC-IBC-2.5mm OneClick cleaners for 2.5 mm SC, ST, FC connector and patch cord (5 qty)
NFC-IBC-MPO OneClick cleaners for MPO/MTP connector (5 qty)
NFC-KIT-CASE-E
Enhanced Fiber Optic Cleaning Kit—includes (1) OneClick cleaner for 1.25 mm
connector, (1) OneClick cleaner for 2.5 mm connector, (1) OneClick cleaner for
MPO/MTP cleaner, a solvent pen, a cleaning cube and a softcase
FT525 FiberInspector Mini and Cleaning Kit
To learn more visit: www.flukenetworks.com/fibercleaning
www.flukenetworks.com/fiberinspection
Fiber Inspection and Cleaning
JackRapid™ Termination Tool
The JackRapid Termination Tool is the industry’s most innovative and time-saving installation tool.
JackRapid allows you to terminate jacks eight times faster than traditional impact tools—with accuracy
that’s unmatched. The patented jack termination tool seats and terminates all wires simultaneously with
one squeeze of an ergonomic handle. The built-in blade cuts off the excess wire after it is seated in the
connector, eliminating the need for a secondary trim step. Simple, one-handed operation reduces hand
fatigue. With JackRapid, you’ll never punch into the palm of your hand or through drywall again.
• Cuts installation time—easy-to-use handle, seats and cuts all wires at once, saving you up to one
minute installation time per jack
• High-quality, consistent terminations—no more compromised connections and wasted jacks
• Simple, one-handed operation with an ergonomically designed handle reduces hand fatigue
Model Description
JR-LEV-1 JackRapid termination tool (for Leviton 41106, 41108, 5G108)
JR-LEV-1-H JackRapid replacement blade head (for Leviton 41106, 41108, 5G108)
JR-SYS-UNI-1 JackRapid termination tool (for Systimax MPS100E, C5, M1BH and Uniprise UNJ600/500/300)
JR-SYS-UNI-1-H JackRapid replacement blade head (for Systimax MPS100E, C5, M1BH and Uniprise UNJ600/500/300)
JR-LEV-2 JackRapid termination tool (for Leviton 61110, 5G110, 6110G)
JR-LEV-2-H JackRapid replacement blade head (for Leviton 61110, 5G110, 6110G)
JR-SYS-2 JackRapid termination tool (for Systimax MGS400, MGS500, MFP420, MFP520)
JR-SYS-2-H JackRapid replacement blade head (for Systimax MGS400, MGS500, MFP420, MFP520)
JR-ORT-2 JackRapid termination tool (for Ortronics TJ5E00, TJ600, TJ610)
JR-ORT-2-H JackRapid replacement blade head (for Ortronics TJ5E00, TJ600, TJ610)
JR-ADC-2 JR-ADC-2, JACKRAPID TERMINATION TOOL (FOR ADC C6a CopperTen® UTP RJ45 jack and the C6 TrueNet® KM8 UTP RJ45)
JR-ADC-2-H JR-ADC-2-H, JACKRAPID REPLACEMENT BLADE HEAD (FOR ADC C6a CopperTen® UTP RJ45 jack and the C6 TrueNet® KM8
UTP RJ45)
JR-ERGOHANDLE JackRapid ergonomic handle
JR-PAN-2 JackRapid termination tool (for Panduit NK688M, NKP5E88M)
JR-PAN-2-H JackRapid replacement blade head (for Panduit NK688M, NKP5E88M)
6. Wires will be seated and cut for
a solid termination.
1. Strip cable jacket with a standard cable strip-
per or the built-in cable stripper.
2. Determine wiring scheme. Dress
all four pairs (eight wires).
3. Insert jack in JackRapid front rst with
IDC slots facing blades of JackRapid.
4. Ensure jack is completely and securely
inserted in jack holder bed with IDC
slots facing the blades.
5. Pull trigger completely and remove
excess wire prior to releasing trigger.
Test Tools and Kits
Get accurate terminations and clean, consistent cuts every time with the JackRapid Termination Tool.
To learn more visit: www.flukenetworks.com/jackrapid
1-800-283-5853 (US and Canada) • www.flukenetworks.com
32 33
D914™ Impact Tool
The D914 Impact Tool is the only punchdown tool to combine torque
and impact. It combines two versatile tools, the hook
and spudger, into the handle. 66/110 blades available.
• Ensures clean, smooth terminations
• Hook and spudger tools are built into the handle
• Automatic spring handle—choose low impact for 24/26 gauge
wire or high impact for 22-gauge wire
• Accept Phillips-head or at screwdriver blade
• Convenient blade storage built into the handle
• Easy blade insertion, locks in place
• Industry standard, internationally accepted with
lifetime warranty
To learn more visit: www.flukenetworks.com/d914
D814™ Impact Tool
The D814 Impact Tool is a deluxe, all-in-one, telecom punchdown
tool and comes with the 66/110 blade. Impact wheel has high and
low settings. Automatic spring mechanism provides the right impact
to seat and/or terminate wires.
• Industry standard with lifetime warranty
• Accepts standard industry blades
• Adjustable spring impact mechanism allows low impact for 24/26
gauge wire or high impact for 22-gauge wire
• Convenient blade storage built into the handle
• Easy blade insertion, locks in place
To learn more visit: www.flukenetworks.com/d814
D914™S Impact Tool
SoftTouch D914S Impact Tool offers an ergonomic design with a soft
rubber handle for better grip and rounded edges to absorb more of
the impact recoil. Includes built-in probe pic/spudger and torque,
allowing you to choose from high-and low-impact settings.
• Reduced hand-fatigue with shock absorbing handle
• Hook and spudger to lift and separate wires
• Automatic spring handle—choose low impact for 24/26 gauge
wire or high impact for 22-gauge wire
• Accepts Phillips-head or at screwdriver blade
• Convenient blade storage built into the handle
• Easy blade insertion, locks in place
• Industry standard, internationally accepted with
lifetime warranty
To learn more visit: www.flukenetworks.com/d914
Model Description
10051000 D914 Impact Tool
10051100 Tool with EverSharp 66 blade
10051110 Tool with EverSharp 110 blade
10051120 Tool with EverSharp 110 and
EverSharp 66 blade
10051501
Tool with EverSharp 110,
EverSharp 66 blade and free
screwdriver blade
Model Description
10061000 D914S Impact Tool
10061100 Tool with EverSharp 66 blade
10061110 Tool with EverSharp 110 blade
10061501
Tool with EverSharp 110,
EverSharp 66 blade and
free screwdriver blade
10061503 Tool with BIX and EverSharp
66/110 cut blade
10061810 Tool with EverSharp 66/110
blade
Model Description
10054000 D814 Impact Tool
10055000 Tool with EverSharp 66 blade
10055110 Tool with EverSharp 110 blade
10055200 Tool with EverSharp 110 and
EverSharp 66 blade
10055501
Tool with EverSharp 110,
EverSharp 66 blade and free
Wood Screw Starter Punch
blade
10055503 Tool with BIX and EverSharp
66/110 cut blade
www.flukenetworks.com/telecom
Test Tools and Kits
Test Tools and Kits
Blades
Fluke Networks increases the versatility and exibility of its line of impact tools by offering a wide variety of interchangeable
blades that permit each tool to perform multiple functions. From our high-performance EverSharp blades, to our unique blade
storage kit cases, Fluke Networks has the blades you need to terminate blocks and jacks quickly.
10056500
EverSharp 66 blade 10057000 10176000
110 blade 10436001 10465001 10645001
10056000
66 blade
630 blade 10176500
EverSharp 110 blade
Centerpunch blade 3M System D blade Wood screw starter
punch
10056225
66 blade, bulk
(must be ordered in
multiples of 100)
10176225
110 blade, bulk
(must be ordered in
multiples of 100)
10565000 10565110 10665000 10051200 10051300
Cut blade,
compatible with
Krone/ADC
Cut blade,
compatible with
Krone/ADC, 110
BIX blade Screwdriver blade
(D914 or D914S only)
Torque Adapter blade
To learn more visit: www.flukenetworks.com/blades
EverSharp™ Blades
Fluke Networks offers three EverSharp blade
designs: the EverSharp 66/110 cut blade, the
EverSharp 110 blade and the EverSharp 66 blades.
Through special processing of the metal, these high
performance blades stay sharper longer than other
competitive blades. These blades t the D914S,
D914 and D814 punchdown tools.
Blade Storage Kit
This unique blade storage case helps prevent loss,
misplacement and damage of impact blades by
keeping them all together in one convenient hard
case. They are sized to t neatly into shirt or pants
pocket or clipped onto belt or tool pouch.
Model Description
10056500 EverSharp 66 blade
10176500 EverSharp 110 blade
10178600 EverSharp 110/66 blade
Model Description
10979003
66 blade kit (2-66 blades,
1-630 blade, 1-Wood Screw
Starter blade) in a storage
case
10979004
110 blade kit (2-110 blades,
1-66 blade, 1-Wood
Screw Starter blade)
10979002 Blade storage case only
1-800-283-5853 (US and Canada) • www.flukenetworks.com
34 35
Electrical Contractor
Telecom Kits
Fluke Networks Electrical Contractor Telecom
Kits are comprised of industry standard
telecommunications tools and test equipment.
Contents include D814™ impact tool, cable
stripper, probe pic, Electrican’s D-Snips,
standard 4-wire modular adapter and
EverSharp™ 66/110 cut blade. Soft carrying
case included for easy organization.
• Choose either Kit I with TS®30 Test Set or Kit
II with Pro3000 Analog Tone and Probe
• D814 industry standard punchdown tool
for reliable terminations
• EverSharp 66/110 cut blade provides
exibility for different block and
jack terminations
• Cable stripper quickly rings and slits
many types of cable
• Use the probe pic to check for loose or
damaged connections
• Cut and strip wire cleaner and faster with
the Electrician’s D-Snips
• Connect to jacks for testing with the standard 4-wire modular adapter
• A soft zippered pouch keeps your tools all in one convenient place
To learn more visit: www.flukenetworks.com/ectkit
Pro-Tool™ Kits
All the professional tools you need to cut,
strip, clean and connect network phone
and data lines to blocks and jacks. Bundled
together in our sleek form-tting PVC
Dur-A-Grip™ tool pouch—holds your tools
securely inside, even upside down. Five tool
kit combinations to choose from to meet a
multitude of applications.
• All kits include ergonomically designed Dur-
a-Grip pouch for convenient tool
storage on belt
• D914™ and D814™ industry
standard punchdown tools make for
solid terminations
• Easy-to-use cable stripper quickly rings and
slits many types of cable
• Cut and strip wire cleaner and faster
with the Electrician’s D-Snips
To learn more visit: www.flukenetworks.com/protool
Model Description
11291000 IS40 Pro-Tool kit
11291400 Pro-Tool kit IS40 pouch only
11292000 IS50 Pro-Tool kit
11293000 IS60 Pro-Tool kit
Pro-Tool Kit Model IS60 IS50 IS40
D914S impact tool
D814 impact tool
Electrician’s D-Snips
Cable stripper
Mini LED Flashlight
Dur-a-Grip pouch
EverSharp 66/110 cut blade
Probe pic
Electrical Contractor
Telecom Kit Telecom Kit I Telecom Kit II
TS30 Test Set with angled
bed-of-nails cord
Pro3000 analog tone
and probe
D814 impact tool
Electrician’s D-Snips
Cable stripper
EverSharp 66/110 cut
blade
Standard 4-wire modular
adapter
Probe pic
Model Description
11290000 Electrical Contractor Telecom Kit I
(with TS30 Test Set)
11289000 Electrical Contractor Telecom Kit II
(with Pro3000 analog tone and probe kit)
11289400 Soft case, Electrical Contractor Telecom kit
IS60
IS50
IS40
Kit I
Kit II
I
I
I
I
I
I
I
I
I
I
I
I
I
I
www.flukenetworks.com/toolkit
Test Tools and Kits
Test Tools and Kits
D-Snips™
The electrician’s D-Snips offer a unique ergonomically-designed
handle that leverages your power.
• Ergonomic design provides 1-1½ times the cutting force with
half the effort
• High-quality forged steel construction for strength and durability
• Serrated blade for non-slip wire cutting
• File and scraper on both blades for cleaning wire
• Notched blade for stripping 19 and 23-gauge wire
• Cuts up to 16-gauge solid and 12-gauge stranded wire
To learn more visit: www.flukenetworks.com/dsnips
Modular Crimper
All-in-one crimping tool for WESS type 6 and 8-position modular
telephone plugs.
• Crimps 8-position RJ-45 connectors and 4 and 6-position RJ-11 and RJ-12 connectors.
• Embedded at cable cutter and stripper
To learn more visit: www.flukenetworks.com/crimper
Cable Splicing Knife
The perfect tool for splitting cable sheaths. Soft, no-slip,
easy-to-grip handle and cutlery-steel blade for durability
and long-lasting blade edge.
• Short blade (1.75 in/4.4 cm) for strength
• Cutlery-steel blade for durability
• Cuts various insulation types
To learn more visit: www.flukenetworks.com/knife
Electrician’s Snips
These versatile Electrician’s Snips feature a le and scraper on both
blades for easy wire cleaning. They also feature a handy notched
scissor blade for quickly stripping 19 and 23-gauge wire.
• High-quality forged steel construction for strength and durability
• File and scraper on both blades for cleaning wire
• Notched blade for stripping 19 and 23-gauge wire
• Cuts up to 16-gauge solid and 12-gauge stranded wire
• Serrated blade for non-slip wire cutting
To learn more visit: www.flukenetworks.com/snips
Model Description
44400000 Cable splicing knife
Model Description
44300000 D-Snips
Model Description
11212530 Modular crimper
Model Description
44500000 Electrician’s snips
1-800-283-5853 (US and Canada) • www.flukenetworks.com
36 37
Cable Strippers
This line of cable strippers includes a double slotted cable
stripper for 22/24 AWG wire installation and a coax stripper
to perform 2-level and 3-level stripping of RG58/59 coaxial
cables. We also offer a combo stripper that cuts and rings
Teon®, smoothly slits ber, copper and coaxial cables and
rings 25-100 pair cable.
• Full line of cable strippers for any job
• Round cable stripper for a variety of exible round cable
• Coax strippers with two or three levels
To learn more visit: www.flukenetworks.com/strippers
Need-L-Lock™ Crimping Pliers
The Need-L-Lock pliers’ patented four-in-one tool combines
UR/UY/UG connector crimper with needle-nose pliers so you
can carry one less tool on your belt. Aligned crimping jaws come down square ensuring a
solid connection. Jaws are grooved to provide a better grip on wires and feature a built-in cutter
and wire stripper.
• Needle nose crimping pliers
• UR/UY/UG connector crimper
• Wire stripper hole for 22-to 24-gauge wire
• Built-in side cutter
• Rubber coated handles for non-slip grip
To learn more visit: www.flukenetworks.com/pliers
Probe Pic
This handy, pocket-sized insulation probe is ideal for
checking for loose or damaged connections or to spread
apart wires for direct access. Its compact size also makes it
perfect for using the pic end for tracing or pulling wires from a bunch.
• Trace and pull wires with the pic end
• Check for loose or damaged connections
• Spread apart wires for direct access
To learn more visit: www.flukenetworks.com/pic
Can Wrench
This can wrench allows universal access to telephone boxes
and pedestals. Open telephone box fasteners and tightens
nuts on binding post terminals.
• Two hex head sockets (7/16 inch and 3/8 inch)
• Color-coded socket ends for quick size identication
• Wrench body constructed of tough, impact resistant and
abrasion resistant material
• Socket ends guaranteed not to split or break up to a maximum torque of 45 pounds
• Two models available with wire stripper in handle (22 or 24 gauge)
To learn more visit: www.flukenetworks.com/wrench
Model Description
11230002 Cable stripper (round cable)
44210013 Double slotted stripper with
cutter, 22/24 gauge
44200013 Double slotted stripper 22/24
gauge
11231257 Coax stripper, 2-level
11231255 Coax stripper, 2 and 3-level
44210015 Double-slotted stripper with
cutter, 24/26 gauge
Model Description
11294000 Need-L-Lock crimping pliers
Model Description
44600000 Probe pic, 105 degree
Model Description
44007000 Can wrench, hex head
44507003 Can wrench with stripper,
22 gauge
44507004 Can wrench with stripper,
24 gauge
10660001 Security key insert
www.flukenetworks.com/tts
Test Tools and Kits
TELEPHONE
TEST SET
COMPARISON
TS®54 TDR TS®52 PRO TS®22A TS®22 TS®25D TS®30 /
TS®120*
TS®19
TDR to detect shorts, opens,
and distance to open
Built-in toner
Display—back lit LCD and
glow-in-the-the
dark keypad
LCD only
Extended range high-
impedance DataSafe
operation in monitor mode
High-impedance DataSafe
operation in monitor mode
Data lockout protection
Data lockout override
DSL/POTS ltering
technology
Low/high voltage
indication
Low current (mA)
indication
Over voltage protection
Over current protection
Two-way speakerphone for
true hands-free conversa-
tions
One-way amplied speaker
for hands-free monitoring
Audible ringer for callbacks
Waterproof—exceeds
American Military Spec.
MIL-STD-810E
RainSafe—safe in severe
weather conditions
DropSafe—passes 20 foot
(6 meter) drop test onto
concrete
Tone and pulse operation
Polarity indication in
talk mode
PBX pause button
Stores nine 18-digit
numbers in repertory dialer
(speed dialing)
Replaceable 9V battery
for powering speaker
*TS120 for outside North America only. 67/33 break/make ratio.
Telephone Butt-Sets and Access Network Test
1-800-283-5853 (US and Canada) • www.flukenetworks.com
38 39
TS®52 PRO LCD Test Set
The TS52 PRO Test Set features the latest in test set technology. Designed with a superior, radiant
liquid crystal display (LCD) user interface, it allows you to see what cannot be heard in any outside plant
environment. The back-lit LCD and glow-in-the-dark keypad brings light to even the darkest of work
environments, providing perfect line diagnostic clarity. The TS52 PRO Test Set is also equipped with
2-way speakerphone and DataSafe™ Pro data protection technology featuring superior high-impedance
monitoring, data lockout and lockout override, making you completely safe.
• Display—back-lit LCD and glow-in-the-the dark keypad
• DataSafe Pro—superior high-impedance monitoring, lockout
and override, making you completely safe in any mode
• DropSafe/RainSafe™—passes 20-foot drop test and designed
for use in rainy conditions
• DSL/POTS ltering technology—allows technicians to clip on a
live DSL line to test POTS service without downing or disrupt-
ing data service
• Two-way, hands-free speakerphone—for true hands-free conversation
• Test Functions:
– Data indication: warns when data is present
– Voltage indication: troubleshooting feature to identify potential line problems
– Current (mA) indication: veries sufcient line current
– Caller-ID: veries service is functional
– DTMF digit grabbing: isolate faulty customer premise equipment
Model Description
52801001 TS52 PRO test set with piercing pin clips
52801004 TS52 PRO test set with 346A plug
52801009 TS52 PRO test set with Angled Bed-of-Nails (ABN)/PP clips
52801RJ9 TS52 PRO test set with Angled Bed-of-Nails (ABN)/PP and RJ-11 plug
To learn more visit: www.flukenetworks.com/ts52
www.flukenetworks.com/tts
Telephone Butt-Sets and Access Network Test
TS®54 TDR Test Set
A three-in-one—TDR, toner and pair identier—premium, VDV test set
Ten testing functions include:
• TDR—nd cable length measurement and locate faults on virtually all types of cable including twisted
pair, coaxial, and parallel conductors
• Toner—ve separate tones for fast and easy differentiation between multiple wire pairs
• SmartTone®—short the correct pair and tone changes for exact pair identication
• Data indication—warns when data is present on the line
• Voltage indication/measurement—identies potential line problems
• Current (mA) indication/measurement—veries sufcient line current
• Caller-ID with Call Waiting CID—veries functional service
• DTMF Digit Grabbing—isolates faulty customer premise equipment
• Detects dial tone, places and receives calls
• Polarity
Model Description
TS54-A-09-TDR Test Set + TDR, ABN with Piercing Pin
TS54-BANA Test Set + TDR, 4 MM Banana, Extra-large Alligator Clips, Test Probe
Accessories
Model Description
BELTCLIP-TS Belt Clip
LEAD-PIRC-PIN Test Leads with Piercing Pin Clips
LEAD-CO-346A Test Leads with a 346A Plug for the Central Ofce1
LEAD-ABN-PPIN Test Leads with Angled Bed-of-Nails (ABN) and Piercing Pin Clips
LEAD-ALIG-CLP Test Leads with Alligator Clips
LEAD-ABNPRJ11 Test Leads with an RJ-11 Plug, Angled Bed-of-Nails (ABN), and Piercing Pin Clips
LEAD-BANA-CLP Test Leads with a 4 mm Banana Plug, Alligator Clips, and Test Probe
HEADSET-TS Headset
Telephone Butt-Sets and Access Network Test
To learn more visit: www.flukenetworks.com/ts54
1-800-283-5853 (US and Canada) • www.flukenetworks.com
40 41
TS®30 Test Set
The TS30 Test Set features a rigid test set case design, at an affordable price. The ergonomic non-slip grip
handle provides improved handling of the set in all weather conditions. Includes DataSafe™ operation so
technicians can clip onto a line in monitor mode, without disrupting existing data trafc.
• High impedance DataSafe operation in monitor mode
• DropSafe™ reliability passes 20-foot drop test
• RainSafe™ protection in severe weather conditions
• Mute switch
• Last number redial
Model Description
30800009 TS30 test set with Angled Bed-of-Nails (ABN)
30800001 TS30 test set with piercing pin clips
To learn more visit: www.flukenetworks.com/ts30
TS®22 Series Test Sets
The TS22 Series offers a unique built-in, one-way amplied speaker that provides three audio levels
for hands-free listening and use with automated voice response systems. Multiple memories enable
storage of nine 18-digit telephone numbers in repertory dialer (speed dialing) for easy access to test
boards, the central ofce and other frequently called numbers. The last number redial feature eliminates
the need to re-key your last entry. The TS22 test set offers an unbeatable combination of reliability,
durability and expanded utility.
• Amplied speaker for hands-free monitoring
• Two-way speakerphone for true hands-free conversation
• DropSafe™ reliability passes 20-foot drop test
• RainSafe™ protection in severe weather conditions
• Stores nine 18-digit numbers in repertory dialer (speed dialing)
Model Description
22801009 TS22A test set with Angled Bed-of-Nails (ABN)
22801007 TS22A test set with ground start cord
22801004 TS22A test set with 346A plug
22801001 TS22A test set with piercing pin clips
22800009 TS22 test set with Angled Bed-of-Nails (ABN)
22800007 TS22 test set with ground start cord
22800004 TS22 test set with 346A plug
22800001 TS22 test set with piercing pin clips
To learn more visit: www.flukenetworks.com/ts22
Telephone Butt-Sets and Access Network Test
TS®25D LCD Test Set
The TS25D Test Set features data lockout and lockout override, making you completely safe in talk or
monitor mode. The DSL/POTS ltering technology allows you to safely draw dial tone without downing DSL.
A built-in analog tone generator simplies wire identication with a probe. An amplied speaker makes
monitoring the line hands-free, so you can keep working. The Talk Battery function provides voltage
to carry voice conversation on non-powered pairs. Also includes Caller-ID and Call-waiting Caller-ID
functions. All in a compact unit with an oversized, robust liquid crystal display (LCD) that makes the
intuitive, common-sense menus easy-to-read and use.
• Caller-ID and Call-waiting Caller-ID
• Amplied speakers for hands-free monitoring
• Data lockout and data lockout override
• Tone generator for wire identication
• Talk battery to power voice conversation on dry
(non-powered) lines
Model Description
25501109 TS25D test set with Angled Bed-of-Nails (ABN) kit (includes pouch and earpiece)
25501009 TS25D test set with Angled Bed-of-Nails (ABN)
25501004 TS25D test set with 346A plug
25500400 TS25D pouch only
25500300 TS25D battery door with belt clip
25500100 Earpiece, TS25D test set
To learn more visit: www.flukenetworks.com/ts25d
TS®19 Test Set
The TS19 Test Set combines all the essential test set features at an affordable price. This test set was
specically designed for in-house telecom technicians. Its high impedance monitor prevents accidental
disruption of service from clipping onto a data line while in Monitor Mode, thus ensuring the integrity of
critical data lines. Features such as tone (DTMF) or pulse operation, talk/monitor capabilities, polarity test
button and last number redial make this test set the perfect combination of features and price.
• High impedance DataSafe operation in monitor mode
• Tone (DTMF) and pulse operation and last number redial
• Polarity indication in talk mode
Model Description
19800009 TS19 test set with Angled Bed-of-Nails (ABN)
19800003 TS19 test set with banana jacks to alligator clips
To learn more visit: www.flukenetworks.com/ts19
www.flukenetworks.com/tts
Telephone Butt-Sets and Access Network Test
1-800-283-5853 (US and Canada) • www.flukenetworks.com
42 43
In-line Modular Adapter (4, 6, and 8-wire)
In-line banjo modular adapters permit testing on working lines without disrupting service.
Quickly determine whether the trouble is in the phone or in the line.
• Easily complete testing and obtain circuit access on working lines without disrupting service
• Clear circuit markings on the sides and bottom of the unit
• Test line status with the 4-wire modular adapter
4-wire Standard Modular Adapter
Provide a quick connect to modular telephone jacks using any standard butt-in test set equipped with
spring clips.
• Easily complete testing and obtain circuit access on working lines without disrupting service
• Clear circuit markings on the sides and bottom of the unit
• Test line status with the 4-wire modular adapter
Spare Modular Adapter Cords (standard and K-plugs)
In-line banjo modular adapters feature replaceable adapter cords which enable broken jack
clips to be replaced without discarding the entire unit. K-plug versions have rugged jack clips.
Model Description
10113000 4-wire modular adapter
10210100 4-wire in-line modular adapter
10210101 4-wire in-line modular adapter with K-plug
10220100 6-wire in-line modular adapter
10220101 6-wire in-line modular adapter with K-plug
10230100 8-wire in-line modular adapter
10230101 8-wire in-line modular adapter with K-plug
To learn more visit: www.flukenetworks.com/modular
Telephone Butt-Sets and Access Network Test
Line Cords and Clips
P4480009 P4480001 P4480004 P4480RJ9 P3218024 P3218028
Line cord with Angled
Bed-of-Nails Clips
Compatible with
52 Series
Line cord with Angled
Piercing
Pin Clips
Compatible with
52 Series
Line cord with 346A
plug (Central Ofce)
Compatible with
52 Series
Line cord with Bed-
of-Nails and RJ-11
plug
Compatible with
52 Series
Line cord with
Straight Bed-of-Nails
Clips
Compatible with
20 Series
Line cord with Angled
Piercing Pin Clips
Compatible with
20 Series
P3218234 P3080009 P1980001 P1980003 P1980007 P1980009
Line cord with Angled
Bed-of-Nails Clips
Compatible with
20 Series
Line cord with Angled
Bed-of-Nails Clips
Compatible with
30 Series
Line cord with Angled
Piercing
Pin Clips
Compatible with
19 Series
Line cord with Banana
Jacks and Alligator
Clips
Compatible with
19 Series
Line cord with Ground
Start cord
Compatible with
19 Series
Line cord with Angled
Bed-of-Nails Clips
Compatible with
19 Series
P3218RJ9 P3218442 P3218202 P4080248 P4080249 P4480008
Line cord with Angled
Bed-of-Nails
Clips and RJ-11 plug
Compatible with
20 Series
Line cord 471A Plug
with Alligator Clips
Compatible with all,
requires 346A Plug
Angled Bed-of-Nails
with Piercing Pin Clips
Compatible with all
Standard locking belt
clip
Compatible with
52 Series
Belt clip
Compatible with
52 Series
TS52/44/42 Replace-
ment Line Cord with
Angled Bed-of-Nails
Clips Only
Compatible with
52 Series
Telephone Butt-Sets and Access Network Test
www.flukenetworks.com/tts
45
1-800-283-5853 (US and Canada) • www.flukenetworks.com
44
Voltage Detector
In just a few seconds, a technician can determine if it’s safe to work around areas such as transformer cases
and circuit breaker housings, power ground wires or newly-driven ground rods, mobile homes, metallic
siding or metal framing, pedestals, cross boxes or conduit, street light xtures or electrical machinery. The
Voltage Detector is a proven life-saver, with more than 30 years of service in telecommunications outside
plant and power utility applications.
• Helps protect against accidental electrocution
• Fast and easy-to-use
• Rated to 20,000 Vac and 2,000 Vdc
Model Description
C9970 Voltage Detector
C9973 Voltage Detector kit—includes Voltage Detector, probe cap, storage bag, temporary bond, ground
cord and handbook
C9974 Voltage Detector kit with test plug
Accessories
Model Description
26100103 Pro3000 Analog Probe replacement tip (two per bag)
C9972 Temporary Bond
C9967 Ground Cord
C9966 Test Plug
C9965 Probe Cap
C9964 Handbook
To learn more visit: www.flukenetworks.com/voltagedetector
Telephone Butt-Sets and Access Network Test
Gold Support
Protect Your Investment and Minimize Business Downtime with Gold Membership 46
What’s Included with Gold Membership? 46
Gold Membership Privileges 47
1-800-283-5853 (US and Canada) • www.flukenetworks.com
46 47
Buy Gold. Make your investment count.
Protect Your Investment and Minimize Business Downtime
with Gold Membership
Gold Membership is much more than just a repair
warranty. It is a comprehensive maintenance and
support program that offers expanded coverage for
Fluke Networks’ products and accessories. It provides a
premium level of support to minimize business down-
time and ensure a high return on your investment.
3-Year Gold Membership provides a 10% discount off
current Gold pricing along with 3-year price protection.
On average customers can save up to 19%
over 3-years by taking advantage of the 3-year
Gold Membership option. Gold Membership is available
for most Fluke Networks products in 1-year or
3-year (save 10% with 3-year) contracts.
What’s Included with Gold Membership?
Benets Gold Member Non-Gold Member
Live Technical Support with exclusive phone numbers
FREE Repair with “rst on bench” turnaround service
Loaner Equipment Service*
FREE Accessory Replacements**
FREE Annual Calibration
Member Only Promotions
Access to Technical Support Web, Email and Phone Web and Email
Response time from Technical Support <2 Hours <24 Hours
Customer Support—Phone and Email 24x7x365 7am-5pm (Pacic Time)
Primary Case Handling Technical Support Engineer Customer Service Agent
*Available in certain geographies
**Applies to accessories included in the original product bundle
www.flukenetworks.com/gold
Gold Membership Privileges
Technical support
Unlimited 24/7 technical expertise with local language support. Gold members are provided with direct members-only priority
phone numbers to our world-class Technical Assistance Centers (TAC).
Repair
Unlimited, no-hassle, no-charge PRIORITY repair services including labor, parts and shipping.
Loaner unit
A loaner unit or replacement unit can be provided during repair, available the next business day for ZERO downtime.
Accessories
Parts and accessories that shipped with your unit and have been qualied as defective or faulty by our technical assistance center
will be replaced free of charge during the term of your Gold membership.
Calibration
One annual precision calibration and factory refresh per annual contract period. In addition, all accessories are inspected and
replaced if faulty.
Upgrades/Updates
Valuable software and rmware upgrades for your unit during the year giving you the latest functionality, improving technical ef-
ciency and troubleshooting.
Discounts and Members-Only Promotions
Special discounts are offered to Gold customers on new products, enhancements and used demo equipment.
Easy Access to Gold Entitlements
Upon purchase, your company will receive a unique Gold Membership Number and PIN for secure access to your online Gold account.
Gold Support
Gold Support
To see a list of supported countries and full terms and conditions, go to www.flukenetworks.com/gold.
Contact your local Fluke Networks representative and order your Gold Membership today!
www.flukenetworks.com
Contact Us
Corporate
Fluke Networks
Everett WA 98203, USA
Customer Service, Technical Support and Training
1-800-283-5853 (Toll free inside U.S. and Canada)
1-425-446-4519 (Worldwide)
Customer Service Email: info@ukenetworks.com
Support Email: support@ukenetworks.com
Training Email: training@ukenetworks.com
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50
countries worldwide. To nd your local ofce
contact details, go to
www.ukenetworks.com/contact.
©2016 Fluke Corporation.
Printed in U.S.A. 04/2016 3158212H
www.ukenetworks.com/facebook
www.ukenetworks.com/twitter
www.ukenetworks.com/linkedin
www.ukenetworks.com/youtube
