Installation Directions
2016-10-06
: Pdf 1000436737-Installationsheet 1000436737-InstallationSheet B5 unilog
Open the PDF directly: View PDF 
.
Page Count: 2
1
NPS15Z
Z-Wave Radio Frequency (RF) Controlled
Plug-In Appliance Module
15 Amps, 120 VAC, Series 300
NOTE: This module must be “included in the Network” only where it will be permanently installed. You cannot “test bench” configure this
module, then install. The proper operation of this node in the mesh network is dependent on it knowing its location with respect to other nodes.
NPS15Z PLUG-IN APPLIANCE MODULE
NuTone’s family of Z-Wave® certified wireless lighting controls (switches,
dimmers, outlets and plug-in modules) brings a new level of intelligent wireless
capability to commercial and residential environments.
The Z-Wave wireless protocol is an international wireless standard for remote
home automation, security and other applications. Embedded in each device,
the Z-Wave smart chip enables two-way RF communication among hundreds
of Z-Wave enabled devices, allowing products and services from multiple
manufacturers to work seamlessly.
NuTone Z-Wave products are easy to install, and allow dealers to create an
integrated wireless network with nearly limitless expansion and interoperability
with security and health monitoring systems, energy management, home
entertainment, appliances, and more.
This product supports 40Kbps data transmission. This product can also
be used for network support in systems that stream metadata. An example
might include transmission of information from audio devices such as song
title, artist, and album information to various displays around the home. As
part of a Z-Wave network, the NPS15Z will act as a wireless repeater to insure
that commands intended for another device in the network are received. This
is useful when the device would otherwise be out of the radio range of the
wireless controller.
INSTALLATION
Plug this Appliance Module into the wall outlet near the load to be controlled,
and plug the load into the Appliance Module. Make sure the load to be
controlled is 15 amps (1800 watts) or less.
To reduce the risk of electric shock, this product has a grounded type plug that
has a third (grounding) pin. This plug will only fit into a grounding type power
outlet. If the plug does not fit into the outlet, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
INCLUDING NPS15Z TO THE NETWORK
1. Prepare the Controller to include a unit to the network, by adding it to a group
(method of adding a node to the network). Refer to controller instructions.
2. The NPS15Z must be in its permanently installed location. Tap the
button on the NPS15Z once.
3. You should see an indication on your Controller that the “DEVICE WAS
INCLUDED” in the network.
✓NOTE: If you have trouble adding the NPS15Z to a group it may be that
the Home ID and Node ID were not cleared from it after testing. You must
first “RESET UNIT” with your controller to remove it from the network.
Although adding it to a group includes it in the network, removing it from
a group does not remove it from the network. If removed from a group, it
functions only as a repeater.
INTEROPERABILITY WITH Z-WAVE™ DEVICES
A Z-Wave network can integrate devices of various classes of products, and
these devices can be made by different manufacturers. The NPS15Z has
Z-Wave certification which guarantees interoperability.
BASIC OPERATION
Button (Local Control)
The button on the NPS15Z allows the user to:
• Turn the attached load on or off.
• Include or exclude the module from the Z-Wave system.
When a controller prompts you to “Send Node ID” or to “Press Button on Unit”,
quickly tap the button once to satisfy those instructions. Tapping button toggles
the load attached ON or OFF.
Remote Control
The NPS15Z will respond to BASIC and BINARY commands that are part of
the Z-Wave system. Refer to your controller’s instructions as to whether your
controller can transmit those commands.
ADVANCED OPERATION
Protection
The NPS15Z supports the Protection Command. The NPS15Z can be set
to any one of three Protection modes by a wireless controller. Refer to your
controller for information on how to set the various modes of Protection. Some
controllers may only be able to set certain settings of Protection:
There are three modes of Protection and they are the following:
• No protection
• Child protection
• Local Button totally disabled
No Protection
When Protection is set to “No Protection” mode,the NPS15Z works normally,
unit will turn on and off with the button on the unit, or with the wireless controller.
Child Protection
When Protection is set to “Child Protection” mode, you are required to press
the button on the unit 3 times rapidly to control the attached load. The NPS15Z
continues to operate normally using a wireless controller.
Button Totally Disabled
When Protection is set to “Button totally disabled” mode the button will not
work to turn the unit on or off. The button can still be used, however, to access
the Z-Wave network. The NPS15Z continues to operate normally using a
wireless controller.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,NPS15Z; P/N: 10005979 X2 INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOL ± .125”; SCALE: 1-1; PAGE 1 OF 2
Button Functions
1. Adds module under the command of Wireless
Controller.
2. Local ON and OFF (push and release).
2
All On/All Off
The NPS15Z supports the ALL ON/ALL OFF commands.
The NPS15Z can be set to respond to ALL ON and ALL OFF commands
four different ways. Refer to your controller for information on how to set the
NPS15Z to operate in the manner you desire. Some controllers may be only
able to set certain settings of ALL ON / ALL OFF response.
The four different ways the NPS15Z can be set up to respond to ALL ON and
ALL OFF commands are:
• NPS15Z will not respond to ALL ON or the ALL OFF command.
• NPS15Z will respond to ALL OFF command but will not respond to ALL ON command.
• NPS15Z will respond to ALL ON command but will not respond to ALL OFF command.
• NPS15Z will respond to ALL ON and the ALL OFF command.
Manufacturer Specific
The NPS15Z supports the Manufacturer Specific command. The NPS15Z can
return Manufacturer Specific information about itself. Refer to your Controller’s
instructions on how to get this information from the NPS15Z.
SUC Support
There must be a Static Update Controller in your Z-Wave system for this
feature to work. The Static Controller can act as a gateway in the system, since
other nodes always know its position (not moved after addition to the network.
The “always listening” advantage of the Static Controller is that other nodes can
transmit information frames to it whenever needed. You can assign an “SUC
Route” to the NPS15Z. Refer to your controller’s instructions on how to do this
(if it supports it). Assigning an SUC Route to the NPS15Z allows it to request
an update of the Z-Wave devices that are between it and the Z-Wave device to
which it was trying to transmit. The NPS15Z will only request an update when
a transmission fails.
CONFIGURATION
The NPS15Z supports the Configuration command. The NPS15Z can be
configured to operate slightly differently that it works when you first install
it. Using the configuration command you can change the following (if your
controller supports it).
Set this parameter to 1 for normal ON/OFF operation. Set this parameter to 0
to enable flash mode which operates as follows:
• With Parameter 104 value set to 0, relay is closed and NPS15Z defaults to
ON (relay closed)
• Whenever the NPS15Z receives a Z-Wave ON command, the NPS15Z will
begin cycling its output relay on and off approximately once per second (1/2
second Off, 1/2 second On) for 20 seconds.
• If at any time during that 20 seconds, the NPS15Z receives a Z-Wave OFF
command, the NPS15Z will stop cycling its output relay and default to ON.
• At any time during that 20 seconds, if the NPS15Z receives a Z-Wave ON
command, the NPS15Z will add an additional 20 seconds on/off cycling of
its output relay. At the end of the 20 seconds, the NPS15Z will again default
to ON (relay closed).
• At any other time, if the NPS15Z receives an OFF command, it will have no
effect and the NPS15Z remains ON.
SPECIFICATIONS
Power: 120VAC, 60 Hz
Signal (Frequency): 908.42 MHz
Load: Incandescent: 600W maximum, 120VAC
Resistive: 15 amps (1800 watts) maximum
120 VAC
Motor: 1/2 H.P. maximum, 120 VAC
Range: Up to 100 feet line of sight between the Controller
and or closest Z-Wave repeater
REGULATORY INFORMATION
The NPS15Z is certified to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions.
FCC NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IC NOTICE
This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme aux
CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Les changements ou modifications non approuvés expressément par la partie responsable de la conformité pourrait annuler
l’autorité de l’utilisateur à faire fonctionner l’équipement.
LIMITED WARRANTY
WARRANTY PERIOD AND EXCLUSIONS: Broan-NuTone LLC (the “Company”) warrants to the original consumer
purchaser of its product (the “Product”) that the product will be free from material defects in the Product or its workmanship
for a period of one (1) year from the date of original purchase. The warranty on the light bulbs provided with the product is one
(1) year and does not cover lamp/bulb breakage. This warranty does not cover accessories or parts that may be purchased
separately and installed with the Product.
The limited warranty period for replacement parts, and for Products repaired or replaced under this limited warranty, shall
continue for the remainder of the original warranty period.
NO OTHER WARRANTIES: THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ANY OTHER
WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS
WARRANTIES, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES IMPLIED BY LAW, INCLUDING WITHOUT
LIMITATION THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT
THAT APPLICABLE LAW PROHIBITS THE EXCLUSION OF IMPLIED WARRANTIES, THE DURATION OF ANY
APPLICABLE IMPLIED WARRANTY IS LIMITED TO THE PERIOD SPECIFIED FOR THE EXPRESS WARRANTY. Some
states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Any oral or
written description of the Product is for the sole purpose of identifying it and shall not be construed as an express warranty.
REMEDY: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or
repair or replace, without charge, any Product or part thereof, to the extent the Company finds it to be covered by and in
breach of this limited warranty under normal use and service. The Company will ship the repaired or replaced Product or
replacement parts to you at no charge. You are responsible for all costs for removal, reinstallation and shipping, insurance or
other freight charges incurred in the shipment of the Product or part to the Company. The Company reserves the right to utilize
reconditioned, refurbished, repaired or remanufactured Products or parts in the warranty repair or replacement process. Such
Products and parts will be comparable in function and performance to an original Product or part and warranted for the
remainder of the original warranty period. This warranty does not cover (a) normal maintenance and service including light
bulbs, batteries or other accessories, (b) normal wear and tear, (c) any Products or parts which have been subject to misuse,
abuse, abnormal usage, negligence, accident, improper or insufficient maintenance, storage or repair (other than repair by
the Company), (d) damage caused by faulty installation, or installation or use contrary to recommendations or instructions,
(e) any Product that has been moved from its original point of installation, (f) damage caused by environmental or natural
elements, (g) damage in transit, (h) natural wear of finish, (i) Products in commercial or nonresidential use, or (j) damage
caused by fire, flood or other act of God. This warranty covers only Products sold to original consumers in the United States
by the Company or U.S. distributors authorized by the Company.
EXCLUSION OF DAMAGES: THE COMPANY’S OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR OR
REPLACE, AT THE COMPANY’S OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY AND THE COMPANY’S SOLE AND EXCLUSIVE OBLIGATION. THE COMPANY SHALL NOT BE LIABLE
FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION
WITH THE PRODUCT, ITS USE OR PERFORMANCE. Incidental damages include but are not limited to such damages
as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing other
property which was damaged if the Product does not work properly.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary
from state to state.
This warranty supersedes all prior warranties and is not transferable from the original consumer purchaser.
THE COMPANY SHALL NOT BE LIABLE TO YOU, OR TO ANYONE CLAIMING UNDER YOU, FOR ANY OTHER
OBLIGATIONS OR LIABILITIES, INCLUDING, BUT NOT LIMITED TO, OBLIGATIONS OR LIABILITIES ARISING
OUT OF BREACH OF CONTRACT OR WARRANTY, NEGLIGENCE OR OTHER TORT OR ANY THEORY OF STRICT
LIABILITY, WITH RESPECT TO THE PRODUCT OR THE COMPANY’S ACTS OR OMISSIONS OR OTHERWISE.
This warranty covers only replacement or repair of defective Products or parts thereof at the Company’s main facility and does
not include the cost of field service travel and living expenses.
GENERAL PROVISIONS: (1) Any assistance Company provides to or procures for consumer outside the terms, limitations
or exclusions of this warranty will not constitute a waiver of such terms, limitations or exclusions, or extend or revive the
warranty. (2) Any action by you for breach of this limited warranty must be commenced within one year after the breach
occurs. (3) Whenever possible, each provision of this limited warranty shall be interpreted in such manner as to be effective
and valid under applicable law, but if any portion is deemed invalid or unenforceable, the remaining portions shall still be
enforceable. The Company will not reimburse you for any expenses incurred by you in repairing or replacing any defective
Product, except for those incurred with the Company’s prior written permission.
The Company will not reimburse you for any expenses incurred by you in repairing or replacing any defective Product, except
for those incurred with the Company’s prior written permission.
HOW TO OBTAIN WARRANTY SERVICE: To qualify for warranty service, you must (a) notify the Company at the address
or telephone number stated below within seven (7) days of discovering the covered defect, (b) give the model number and
part identification and (c) describe the nature of any defect in the Product or part. At the time of requesting warranty service,
you must present evidence of the original purchase date. If you cannot provide a copy of the original written limited warranty,
then the terms of the Company’s most current written limited warranty for your particular product will control. The most current
limited written warranties for the Company’s products can be found at www.NuTone.com .
Broan-NuTone LLC 926 West State Street, Hartford, WI 53027 www.NuTone.com Toll Free (855) 249-0610
If you must send the Product or part to the Company, as instructed by the Company, you must properly pack the Product or
part—the Company is not responsible for damage in transit.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,NPS15Z; P/N: 10005979 X2 INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOL ± .125”; SCALE: 1-1; PAGE 2 OF 2
Copyright © 2015 Broan-NuTone LLC 10005979 X2
Z-Wave® is a registered trademark of Sigma Designs
