Lutron Maestro MSCL OP153M WH Spec Sheet Brochure
2016-10-06
: Pdf 1000475233-Brochure 1000475233-Brochure B5 unilog
Open the PDF directly: View PDF 
.
Page Count: 9
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Maestro®Occupancy/Vacancy Sensor with C•L Dimmer Sensor
369748b 1 03.13.13
MaestroR Occupancy Sensor C•LR Dimmer
LutronR MaestroR occupancy sensor C•LR dimmers
are lighting controls with passive infrared sensors that
automatically control the lights in an area. These sensors
detect heat from occupants moving within an area to
determine when the space is occupied. The MaestroR
occupancy sensor C•LR dimmer combines a MaestroR
C•LR dimmer with an occupancy or vacancy sensor.
Features
• Controls CFL, LED, incandescent, and halogen
load types *
• Passive infrared motion detection with exclusive
LutronR XCTT Technology for fine motion detection
• 180˚ sensor field-of-view
• Up to 30 ft x 30 ft (9 m x 9 m) [900 ft2 (81 m²)] major
motion coverage and 20 ft x 20 ft (6 m x 6m)
[400 ft2 (36 m²)] minor motion coverage
• Occupancy version can be set to auto-on/auto-off or
manual-on/auto-off
• Vacancy version available to meet CA Title 24
requirements
• Adjustable timeout (1, 3, 5, 15, or 30 minutes) and
high/low sensitivity adjustment
Models Available
• Adjustable settings for auto-on light level (occupied
level): 100%, 50%, last light level, or locked preset
light level
• Off warning fades lights to off over a period of
10 seconds
• Advanced MaestroR dimmer features available (locked
preset, fade-to-on, and fade-to-off, etc.)
• All models have single pole and multi-location capability
• Works with a single standard mechanical 3-way switch
or up to 9 companion dimmers/switches (MA-R or
MSC-AD) **
Model Number *** Description Sensor Operation Maximum Capacity
MSCL-OP153M-XX Occupancy/vacancy single-pole/
multi-location
Auto-on/auto-off or
manual-on/auto-off
600 W incandescent/halogen
150 W CFL/LED *
MSCL-VP153M-XX Vacancy single-pole/multi-location Manual-on/auto-off 600 W incandescent/halogen
150 W CFL/LED *
* For a complete list of compatible DIMMABLE CFLs and LEDs please visit www.lutron.com/dimcflled
** If using with standard mechanical 3-way switch, some rewiring and dimmer programming is required
*** XX in model number represents color/finish code
1
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Maestro®Occupancy/Vacancy Sensor with C•L Dimmer Sensor
369748b 2 03.13.13
Specifications
Regulatory Approvals
• UL Listed to U.S. and Canadian safety requirements
• Title 20/24 certified lighting control device
– Complies with Title 20 and Title 24 Section 119
(Until Jan 1st, 2014)
• Title 20/24 certified lighting control device
– Complies with Title 20 and Title 24 Section 110.9
(After Jan 1st, 2014)
Power
• Operating voltage: 120 V~ 60 Hz
Environment
• Ambient operating temperature: 32 °F to 104 °F
(0 °C to 40 °C), 0%-90% humidity, non-condensing;
indoor use only
Warranty
• 5 Year Limited Warranty
For additional Warranty information, please visit:
www.lutron.com/TechnicalDocumentLibrary/Sensor_
Warranty.pdf
Key Design Features
Dimmer
• On a single-tap, lights fade ON or OFF
• On a double-tap, lights go to full ON
• When ON, press and hold to engage a long fade
to OFF
• Light levels can be fine-tuned by pressing and
holding the dimming rocker until the desired light
level is reached
Custom Sensor Settings
Timeout Options
• 1 Minute
• 3 Minute
• 5 Minutes (default)
• 15 Minutes
• 30 Minutes
• Test Mode
– Short (less than 15-second) timeout for testing
sensor coverage. After entering, device will exit
test mode automatically after 5 minutes, or
when any button is pressed.
Sensitivity Options
• High sensitivity (default)
• Low sensitivity
Auto-ON Options
• Occupancy (default): Auto-ON / Auto-OFF
– Occupancy Mode is also called “Auto-On: Enabled”
• Vacancy *: Manual-ON / Auto-OFF
– Vacancy Mode is also called “Auto-On: Disabled”
* There is a 15-second grace period that begins when the lights are
automatically turned off, during which the lights will automatically turn
back on in response to motion. This grace period is provided as a safety
and convenience feature in the event that the lights turn off while the
room is still occupied, so that the user does not need to manually turn the
lights back on. After 15 seconds, the grace period expires and the lights
must be manually turned on.
• Ambient Light Detection (ALD): Lights turn on only if
natural light in room is low
– Smart—Ambient light threshold adjusts to the
user’s preference **
** If sensor turns on when there is enough natural light, or if sensor does
not turn on when there is not enough natural light, press the large button
within 5 seconds of entering the room. Over time, this interaction will
“teach” the sensor your preferred setting.
• Off While Occupied (OWO)
– When the sensor dimmer is manually turned off,
the sensor dimmer will not turn the lights back on
automatically while the room is occupied.
– Once the room is vacated, the Auto-ON feature
returns to normal operation after the timeout period
has expired.
– This may be the preference in conference rooms
or classrooms while viewing presentations. This
feature requires motion to keep the lights off.
Occupied Level Options
Occupied Level is the light level that the sensor
dimmer will turn ON to when motion is detected.
• 100% (default)
• 50%
• Preset
– While in preset mode, lights will automatically turn
to the last level or to the “Locked Preset” level if a
“Locked Preset” has been selected in Advanced
Programming.
2
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Maestro®Occupancy/Vacancy Sensor with C•L Dimmer Sensor
369748b 3 03.13.13
Control Voltage Load Type
1Minimum
Load
Maximum Load Neutral
Connection
Required
Not Ganged End of
Gang
Middle of
Gang
MSCL-OP153M
MSCL-VP153M 120 V~
Incandescent,
halogen,
CFL, LED
2
1 bulb, or
as noted
on
approved
bulb list
3
600 W incan/
halogen
or
150 W CFL/
LED
500 W incan/
halogen
or
150 W CFL/
LED
400 W incan/
halogen
or
150 W CFL/
LED
NO
Load Type and Capacity
1 Dimmer Load Type: designed for use with permanently installed lighting fixtures only. Do not install dimmers to control receptacles or motor-operated appliances.
2 For mixed load types, see Mixed Load Type and Capacity section.
3 For a complete list of approved Dimmable CFLs and LEDs, please visit www.lutron.com/dimcflled. For questions call: 1.800.523.9466.
Additional Information
• For MaestroR Occupancy sensing switch models, please see LutronR P/N 369666 at www.lutron.com.
• Lutron Technical Hotline: 1.800.523.9466.
Mixed Load Type and Capacity
Total W CFL/LED
+
A B C
0 W 10 W – 600 W 10 W – 500 W 10 W – 400 W
1 W – 25 W 0 W – 500 W 0 W – 400 W 0 W – 300 W
26 W – 50 W 0 W – 400 W 0 W – 300 W 0 W – 200 W
51 W – 75 W 0 W – 300 W 0 W – 200 W 0 W – 100 W
76 W – 100 W 0 W – 200 W 0 W – 100 W 0 W – 50 W
101 W – 125 W 0 W – 100 W 0 W – 50 W 0 W
126 W – 150 W 0 W 0 W 0 W
Derating Chart
Placing dimmers adjacent
to mechanical switches
does not require derating.
A B CB B B
INC / HAL
A B C
LED
DEL
LFCA
CFL
AFC
LFCA
CFL
AFC
LED
DEL
Incandescent / Halogen : Total Wattage
Determine allowable wattage (W) of
dimmer by following the steps below.
If multiple dimmers are to be installed
adjacently in the same wallbox, derating
is required.
Derating Chart
1. Determine total wattage of CFL/LED
bulbs installed for dimmer control.
2. Determine total wattage of Incandescent/
Halogen bulbs to be controlled by the
dimmer.
3. Use the Derating Chart to determine
if your total wattages are within the
allowable range of your configuration.
4. Derating Procedure (if necessary)
If multiple dimmers are installed
adjacently in the same wallbox, heat fins
MUST be removed between adjacent
dimmers. This will permanently derate
the dimmer, reducing its total allowable
Incandescent/Halogen wattage.
Example
If heat fins from one side of dimmer are removed (see B in chart) and you have two
24 W CFL bulbs installed (Total CFL Wattage = 48 W), you may add up to 300W of
Incandescent/Halogen lighting.
Heat Fins
3
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Maestro®Occupancy/Vacancy Sensor with C•L Dimmer Sensor
369748b 4 03.13.13
Horizontal Beam Diagram
5 ft
(1.5 m)
5 ft
(1.5 m)
0
10 ft
(3 m)
10 ft
(3 m)
15 ft
(4.5 m)
15 ft
(4.5 m)
20 ft
(6 m)
20 ft
(6 m)
25 ft
(7.5 m)
25 ft
(7.5 m)
30 ft
(9 m)
30 ft
(9 m)
Vertical Beam Diagram
5 ft
(1.5 m)
010 ft
(3 m)
10 ft
(3 m) 15 ft
(4.5 m)
15 ft
(4.5 m) 20 ft
(6 m)
20 ft
(6 m) 25 ft
(7.5 m)
25 ft
(7.5 m) 30 ft
(9 m)
30 ft
(9 m)
4 ft
(1.2 m)
0
NEMA WD7 Test Grid Coverage (High Sensitivity Setting)
5 ft
(1.5 m)
5 ft
(1.5 m)
0
10 ft
(3 m)
10 ft
(3 m)
15 ft
(4.5 m)
15 ft
(4.5 m)
5 ft
(1.5 m)
Major motion coverage: 900 ft( (81 m()
Minor motion coverage: 400 ft( (36 m()
MaestroR Occupancy Sensor C•LR Dimmer Placement and Operation
• The ability of the sensor dimmer to detect motion requires line-of-sight of room occupants. The sensor dimmer
must have an unobstructed view of the room.
• Hot objects and moving air currents can affect the performance of the sensor dimmer. For best performance, the
sensor dimmer should be mounted at least 4 ft (1.2 m) away from HVAC vents and light bulbs.
• The performance of the sensor dimmer depends on a temperature differential between the ambient room temperature
and that of room occupants. Warmer rooms may reduce the ability of the sensor dimmer to detect occupants.
35 ft
(10.7 m)
4
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Maestro®Occupancy/Vacancy Sensor with C•L Dimmer Sensor
369748b 5 03.13.13
Mounting
Wallbox
MaestroR
Occupancy
Sensor C•LR
Dimmer
Wallplate
Adapter
Adapter
Mounting
Screws Wallplate
Mounting
Screws
Wallplate / Adapter purchased
separately.
Operation
Status LEDs
Indicate light level; glow softly as night
light when light is off
Sensor
LED *
Dimming Rocker
Press to brighten
Press to dim
Tapswitch
Tap on / off;
Double-tap - lights go to full on
Sensor Lens
FASST
Front
Accessible
Service
Switch
IMPORTANT NOTICE:
FASST – Front Accessible Service Switch – to service load, remove power by pulling the FASST switch out completely
on either the sensor dimmer or companion dimmer. After servicing load, push the FASST switch back in fully to restore
power to the control. Once power has been restored, the sensing dimmer can be manually turned on or off but will not
automatically control the load for the first 2 minutes.
NOTE:
* LED only pulses to acknowledge motion when there is
motion AND the load is ON.
5
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Maestro®Occupancy/Vacancy Sensor with C•L Dimmer Sensor
369748b 6 03.13.13
Dimensions
Front View Side View
5/16
(8)
1/8
(3)
11⁄8
(30)
411⁄16
(119)
215⁄16
(75)
Note: MSCL-OP153M and MSCL-VP153M have screw terminals.
Measurements shown as: in (mm)
6
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Maestro®Occupancy/Vacancy Sensor with C•L Dimmer Sensor
369748b 7 03.13.13
Wiring Diagrams
Single Location Installation
1
MSCL-OP153M and MSCL-VP153M
Brass
Black
Blue
1
Ground
Line/Hot
Neutral
120 V~
60 Hz
Load
Wiring Diagram 1
Sensor Dimmer
Multi-Location Installation
2, 3, 4
MSCL-OP153M and MSCL-VP153M with MA-R or MSC-AD
Brass
Black
Blue
Ground
Companion Dimmer
Brass
Black
Blue
Ground
120 V~
60 Hz
Brass
Black
Blue
Ground
Line/Hot
Neutral
Load
Sensor Dimmer Companion Dimmer
Wiring Diagram 2
1 When using controls in single location installations, tighten the blue terminal. Do not connect the blue terminal to any other wiring or to ground.
2 Up to 9 companion dimmers may be connected to a sensor dimmer. Total blue terminal wire length may be up to 150 ft (46 m).
3 Only one sensor dimmer can be used per multi-location circuit.
4 Sensor dimmer can be installed in any location in the circuit.
Green
Wire
Green
Wire
Green
Wire
Green
Wire
7
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Maestro®Occupancy/Vacancy Sensor with C•L Dimmer Sensor
369748b 8 03.13.13
Wiring Diagrams (continued)
1 Only one sensor dimmer can be used per multi-location circuit.
2 A single standard mechanical 3-way switch or up to 9 companion dimmers may be connected to a sensor dimmer. Standard mechanical 3-way switch
cannot be combined with companion dimmer. Total blue terminal wire length may be up to 150ft (46m).
3 Diagram 3 shows a typical retrofit scenario, where one mechanical 3-way switch is being replaced with a sensor dimmer. The remaining mechanical 3-way
switch needs to be modified to effectively convert it to a single pole switch. For new construction, a standard mechanical single pole switch can be used here.
3-way Installation with Standard Mechanical Switch (120 V~)
1, 2
MSCL-OP153M and MSCL-VP153M
Brass
Blue
Green
Wire
Ground
Sensor Dimmer
Green screw
Ground
120 V~
60 Hz
Line/Hot
Neutral
Load
Standard
mechanical switch
3
Black
Jumper wire
Different
color screw
(Common)
Wiring Diagram 3
OR
Black
Ground
Sensor Dimmer
Green
Wire
Ground
120 V~
60 Hz
Line/Hot
Neutral
Load
Standard
mechanical switch
3
Blue
Jumper wireDifferent
color screw
(Common)
Green screw
Brass
8
®
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Maestro®Occupancy/Vacancy Sensor with C•L Dimmer Sensor
369748b 9 03.13.13
Colors and Finishes
Gloss Finishes Satin Finishes
Taupe
TP
Turquoise
TQ
Plum
PL
Merlot
MR
Terracotta
TC
Sienna
SI
Midnight
MN
Hot
HT
Desert Stone
DS
Due to printing limitations, colors and fi nishes shown cannot be guaranteed to perfectly match actual
product colors.
Eggshell
ES
Biscuit
BI
Snow
SW
Palladium
PD
Greenbriar
GB
Bluestone
BG
Mocha
Stone
MS
Goldstone
GS
Sea Glass
SG
Stone
ST
Limestone
LS
White
WH
Gray
GR
Brown
BR
Ivory
IV
Almond
AL
Black
BL
Light
Almond
LA
9
