Installation Directions
2014-10-23
: Pdf 118094-Installationsheet 118094-InstallationSheet Batch9 unilog
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
500 Series STEEL DIRECT VIEW LED EXIT Model Number: Accessories: Job: Type: Approvals: FEATURES • Enclosure constructed of rugged 20 gauge steel • Solid 1/8” thick, vandal-resistant, polycarbonate lens • Remote capabilities (6 volt) - up to 18 watts • Low voltage disconnect eliminates deep discharge • Brown-out, short circuit and voltage surge protection • Overcharge protection • Flasher/buzzer options to meet ADA regulations • Maintenance-free lead acid battery • Optional NiCad battery available • Universal mounting - ceiling or wall mount • ETL listed 90 minute emergency run time, 24 hour recharge time • Constant, uniform illumination by long-life, high intensity, red or green LEDs The 500 Series is the brightest most visible sign in the industry in both normal and smoke-filled environments. Constructed of durable 20 gauge steel, this direct view exit provides bright illumination with individual LEDs spelling the word EXIT. • Fully-illuminated 6” characters with 3/4” stroke • Optional Guardian Self-Diagnostics available (G1) • Chevron-style, universal arrows • 120/277V dual primary, 60Hz input • Standard finishes: Black or white • Complete fixture series meets American Recovery and Reinvestment Act of 2009 (ARRA) requirements and Buy American provisions RENEGADE COMPATIBLE WARRANTY Any component that fails due to manufacturers defect is guaranteed for 25 years with a separate 5 year pro-rated warranty on the battery. The warranty does not cover physical damage, abuse or acts of God. Manufacturer reserves the right to charge for such repairs if deemed necessary. ORDERING INFORMATION SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Example: 502-WB-WH-DR-C3-EL2A Series Power Source Finish Options (Factory Installed) EL Option (Single Face Only) 502 = Red Single Face LB = AC Only WH = White G1 = Self-Diagnostics EL2A4 = PAR36 White Thermoplastic 503 = Red Double Face WB = With Battery BL = Black DL = Downlight EL2B4 = PAR36 Black Thermoplastic G502 = Green Single Face NC1 = NiCad DR = Damp Location Rated EL2E4 = PAR36 Chrome FL = Flasher EL2F4 = PAR36 White Aluminum BZ = Buzzer EL2G4 = PAR36 Black Aluminum FB = Flasher & Buzzer EL0 = 18W Remote Capacity (No Lamps) G503 = Green Double Face Custom Color Faceplates (Option “C”) A1 = Fire Alarm Interface w/FL Option EL15 = (1) Remote Lamp Head A2 = Fire Alarm Interface w/FB Option REN-2 = (2) Renegade 3.6W LED Lamps 2CI12 = 2 Circuit Input 120/120V Accessories6 (Field Installed) C3 = Black Face w/Red Letters 2CI72 = 2 Circuit Input 277/277V C4 = Black Face w/Green Letters 2CI172 = 2 Circuit Input 120/277V TRHT-6H = Tamper Tool C6 = White Face w/Red Letters TF3 = Extended Run Time Battery ER1-KIT = 1’ Pendant Mount Kit C9 = Brushed Chrome Face w/Black Letters TRH = Tamper Resistant Hardware ER2-KIT = 2’ Pendant Mount Kit C10 = White Face w/Green Letters C = Custom Color Faceplates WG-1 = Wire Guard (Back Mount) WG-2 = Wire Guard (End Mount) WG-3 = Wire Guard (Ceiling Mount) WG-5 = Wire Guard EL w/Side Mounted Lamps (Back Mount) WG-6 = Wire Guard EL w/Top Mounted Lamps (Back Mount) XG-1 = Poly Guard (Back Mount) XG-3 = Poly Guard (Ceiling Mount) XG-EL90 = Poly Guard EL w/Side Mounted Lamps (Back Mount) XG-6 = Poly Guard EL w/Top Mounted Lamps (Back Mount) Not available with EL option LB only, for use with inverter or generator applications only 3 Continuously flashes in emergency (DC) mode - not available with EL option Includes (2) 6V/5.4W PAR36 lamps Consult factory 6 Order as separate line item 1 4 2 5 10800047 02/13 CONSTRUCTION Our specification grade 500 series enclosure, cover, face plate, and mounting canopy are 20 gauge galvanized steel with baked-on, powder coated paint. Face plate has 3/4" black letters with red or green LEDs. 1/8" polycarbonate shield protects LEDs from impact. *Optional face plates are available Stencil letters are 6” high with 3/4” stroke, with minimum of 100 ft viewing distance rating as required by UL924 standard. ILLUMINATION Illumination of the 500 series is accomplished utilizing high-intensity, long-life LEDs exceeding UL 924 requirements for brightness and uniformity. Starting at only 4 watts, LEDs provide excellent, even illumination while maximizing energy efficiency. LEDs are a maintenance-free solution, providing up to 100,000 hours of use without failure. EMERGENCY LIGHTS - (Option: EL2(X)) Emergency lights are single or double face compatible with field-selected top or side mounting. Choice of one or two 6 volt, 5.4 watt high intensity incandescent lamp heads. The 500 series is RENEGADE compatible - 3.6W LED per head. Flashing LED display in emergency mode is standard with emergency lights. ELECTRICAL Dual-voltage input 120 or 277VAC @ 60Hz. Sealed Lead Acid Battery - SLA (With Battery Only) Exitronix sealed lead acid batteries are maintenance-free with a life expectancy of 5 years. Sealed lead acid batteries provide a relatively large power-to-weight ratio making them ideal for emergency applications. Lead Acid batteries are constructed of a series of plates stacked with separators designed to optimize the efficiency and prolong the life of the battery. Lead Acid batteries perform optimally in temperatures ranging from 15-40 degrees C. Sealed Nickel Cadmium Battery - NiCad (Option: NC) Exitronix sealed nickel cadmium batteries are maintenance-free with a life expectancy of 15 years. Nickel cadmium batteries offer high discharge rates and continue to perform in a vast temperature range from 0-40 degrees C. NiCad technology provides long lasting, safe and reliable performance by utilizing the jelly-roll design and allows a Ni-Cad cell to deliver a much higher maximum current than an equivalent size alternative battery. As a relatively larger area of the electrode is in contact with the active material in each cell, the internal resistance for an equivalent sized NiCad cell is lower which increases the maximum current that can be delivered. Brownout Circuit The brownout circuit monitors the flow of AC current to the unit and triggers the emergency lighting system once a set reduction of AC power occurs. This dip in the voltage will cause many fixtures to extinguish causing loss of normal lighting even though a total power failure has not occurred. Low Voltage Disconnect When the battery’s terminal voltage falls below predetermined levels, the low-voltage circuit disconnects the emergency lighting load. The disconnect remains in effect until normal power is restored, preventing deep battery discharge and improving the life of the battery. The disconnect will also automatically reconnect the load circuit once the battery voltage returns to a normal value after charging. Solid-State Transfer The unit features a solid-state switching transistor which eliminates damaged contacts or mechanical failures associated with relays. The switching circuit is designed to detect a loss of AC power and automatically energizes the lamps. Upon restoration of the AC voltage, the emergency lamps will switch off and the charger will automatically recharge the battery. Overload and Short-Circuit Protection The solid-state overload monitoring system in the DC circuit disconnects the lamp load from the battery should excessive wattage demands be made and automatically resets when the overload or short-circuit is removed. This overload current protective characteristic eliminates the need for fuses or circuit breakers for the DC load. OPTIONS Made in the USA (STANDARD) Many of our products can be produced or transformed to comply with the American Recovery and Reinvestment Act of 2009 (ARRA) requirements and Buy American provisions. These fixtures meet LEVEL 1 compliance when option is requested - please call factory for details with questions. Damp Location Rated (Option: DR) Damp location rating ensures the fixture is designed to operate safely in outdoor locations that are protected from the direct elements. Damp location rated fixtures may be installed indoors. Products with damp location ratings are not designed to withstand constant or significant moisture or direct contact with water or steam. Guardian Self-Diagnostic (Option: G1) The Guardian circuit continuously monitors the operating condition of the battery charging circuit and battery supply voltage. The purpose of this option is to provide visual signaling in response to a fault at the EXIT sign battery and/or battery charger. If a failure is detected, visual status will occur immediately via the CHARGER LED and/or the BATTERY FAULT LED. The LEDs will stay illuminated until the fault is corrected. Flasher (Option: FL) When normal power is lost and the emergency unit goes into back up power mode, this unit will flash on and off - providing a highly visual signal as to emergency status. Audible Alarm (Option: BZ) When normal power is lost and the emergency unit goes into back up power mode, this unit will buzz - providing a highly audible signal as to emergency status. Flasher & Audible Alarm (Option: FB) When normal power is lost and the emergency unit goes into back up power mode, this unit will flash on and off while buzzing - providing a highly visual and audible signal as to emergency status. Fire Alarm Interface (Option: A1 or A2) Our fire alarm interface option ties into the building’s fire alarm system allowing for exits and emergency units to be triggered prior to loss of power. A1: Fire alarm interface including Flasher option A2: Fire alarm interface including Buzzer option Two-Circuit Operation (Option: 2CI, 2CI-1, 2CI-7) Two circuit operation features for emergency lighting allows the dual input of power sources for units less battery (AC only). The purpose of this feature is to provide the compatibility of our emergency units in applications where inverters or alternate back up power sources are utilized. Vandal Lens (Option: VL) Providing a vandal lens to exit fixtures offers additional protection to the unit against intentional or unintentional abuse. Tamper Resistant Hardware (Option: TRH) Tamper resistant hardware adds an additional layer of protection to the unit, preventing unwanted access to the interior of the unit or removal of the face plates. CONFORMANCE TO CODES & STANDARDS The 500 Series is ETL listed and meets or exceeds the following: UL 924, NEC requirements and NFPA 101. DIMENSIONS 5.25” 4.625” 9.25” 8.5” Test Button Our easily located test button allows for manual verification of proper operation of the transfer circuit and emergency lamps. INSTALLATION Installs in minutes with easy-to-read instructions and detailed diagrams. No special hardware or tools necessary. Internally housed components and battery eliminate the use of a canopy when back mounting single faced exits. Mounting canopy included. 800.533.3948 • www.barronltg.com 12.375” 2.75”
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Create Date : 2014:09:26 10:55:17-07:00 Metadata Date : 2014:09:26 10:55:36-07:00 Modify Date : 2014:09:26 10:55:36-07:00 Creator Tool : Adobe InDesign CC (Windows) Instance ID : uuid:adbe127a-6203-4394-ae37-c8690a3ef849 Original Document ID : adobe:docid:indd:afaf4d6a-21ae-11db-99c1-d3b11ef8a98f Document ID : xmp.id:5f00cabe-c7e6-8948-b278-6f67c463a08d Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:343434593C7CE211BA698D65295FC568 Derived From Document ID : xmp.did:984E5EBC9461E1118F79C5089F5D0EAB Derived From Original Document ID: adobe:docid:indd:afaf4d6a-21ae-11db-99c1-d3b11ef8a98f Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC (Windows) History Changed : / History When : 2014:09:26 10:55:17-07:00 Format : application/pdf Producer : Adobe PDF Library 11.0 Trapped : False Page Count : 2 Signing Date : 2014:09:26 10:55:36-07:00 Signing Authority : ARE Acrobat Product v8.0 P23 0002337 Annotation Usage Rights : Create, Delete, Modify, Copy, Import, Export Document Usage Rights : FullSave Form Usage Rights : Add, FillIn, Delete, SubmitStandalone Signature Usage Rights : Modify Creator : Adobe InDesign CC (Windows)EXIF Metadata provided by EXIF.tools