HC 207 Installation Directions

: Pdf 131589-Installationsheet 131589-InstallationSheet 785652 Batch5 unilog

Open the PDF directly: View PDF .
Page Count: 2

WARNING: B E SURE THE ELECTRICITY TO THE WIRES YOU ARE

WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED OR THE

C IRCUIT BREAKER OFF.

1. Secure surface mount ring to surface

by marking hole location on surface

and screw surface mount ring to

surface making sure surface mount ring does not ex out of round.

2. Drill wire exit hole in surface or run wire thru notch in surface mount ring.

3. Line up retaining springs on ture housing with grooves in surface

mount ring and press xture housing into surface mount ring.

1. Drill a 2 3/4” dia. hole in surface.

2. Press ture housing into

2 3/4” dia. hole.

SURFACE MOUNTING

INSTALLATION AND SAFETY INSTRUCTIONS HC-207

FOR YOUR SAFETY

RECESS MOUNTING

*NOT INCLUDED

*TRIM

1/8”

HOOKS (2)

SLOTS (4)

RETAINING SPRING (2)

SURFACE

MOUNT

RING

SCREWS (2)

GROOVES (2)

HOLES (2)

NOTCH

FIXTURE

HOUSING

*Lamp

061814

2 3/4”

U.S. PATENT #5,465,199

FIG. 1

FIXTURE

WIRE

WARNING: Use of other manufacturer’s components will void warranty, safety

listing and create a potential safety hazard.

CAUTION: RISK OF FIRE. Must use SeaGull No. 9488 fused plug if use

with transformers over 60w at 12 volts or 100w at 24 volts.

ATTENTION-RISQUE D'INCENDIE MAX 18 WATT TYPE WEDGE T5

CAUTION-RISK OF FIRE MAX 18 WATT TYPE WEDGE T5

(UTILISER SEULEMENT AVEC AMBIANCE CÂBLE 105°)

CAUTION: RISK OF FIRE. Use only 12v lamps with 12v systems. Use

of 12v lamps with 24v system may result in damage to the system

and surrounding area.

ATTENTION : RISQUE D'INCENDIE. UTILISER UNIQUEMENT DES LAMPES 12V

AVEC SYSTÈMES 12V. UTILISATION DE LAMPES DE 12V à 24V SYSTÈME PEUT

ENTRAÎNER DES DOMMAGES AU SYSTÈME ET LA RÉGION AVOISINANTE.

(USE ONLY WITH AMBIANCE 105° CABLE)

ATTENTION : RISQUE D'INCENDIE. Devez utiliser che SeaGull no 9488

fusionnés si utiliser avec des transformateurs de plus de 60w à 12 volts ou

100w à 24 volts.

.SeaGullLighting.com

HC-207 www

FINAL INSTALLATION AND FUSING HC-207

There are several ways to install the 9485 (disk-lights) using

the 9774, 18w, 12V xenon lamps = (actual consumption 16.2w):

1. When using a 60w max transformer (class II)

you are able to directly

hook up three (3) 9485 to the junction box as in Figure 1.

2. For a run larger than three (3) disk-lights you must use a class I transformer

(larger

than 60w). The following example demonstrates a run of

eight (8) 9485 disk-lights (8 x 16.2w each = 130w), in this case you

will need to use a150w transformer.

60W

J-BOX

9485 (3)

FIGURE 1

150W

TRACK & CABLE 9488 (8) FUSED PLUGS

9485 (8) FIGURE 2

FUSED PLUG INSTALLATION (NOT INCLUDED)

TRIM INSTALLATION

*NOT INCLUDED

1. Cut wire to desired length.

2. Split ends of wire about (1/2”) and insert each end of the wire

as far as possible into the plug. Do not strip any insulation o

the wire.

3. Insert contact into one end of plug and press, or use pliers

until contact is ush with plug. Repeat with other contact

(see illustra tion).

4. Twist wires sideways, insert into notch in plug and twist back

straight.

5. Snap plug on cable.

6. Install lamp (18w max.)(not included).

1. Secure trim (not included) to housing by inserting

hooks on trim into two of the four slots in housing and

twist clockwise until trim snaps in place. Bend hooks up

slightly (max. 1/8”) if trim is too hard to turn and lock into

position on housing.

WARNING: Use of other manufacturers components

will void warranty, safety listing and create a

potential safety hazard.

NOTCH

CONTACT

*FUSED

PLUG

9488

*CABLE

*TRACK

FIXTURE WIRE

*FUSED

PLUG

9488

*NOT INCLUDED

-

.

CAUTION: RISK OF FIRE. 12V LAMPS MUST NOT BE USED IN A 24V SYSTEM.

INSTALL CABLE SO THAT CAUTION PRINTED ON CABLE IS VISIBLE AFTER

INSTALLATION AND ATTACH 24V CAUTION LABELS (SUPPLIED WITH THE

24V TRANSFORMER) ON OR ALONG THE TRACK EVERY 4 FT.

ATTENTION : RISQUE D'INCENDIE. LAMPES 12V NE DOIVENT PAS SERVIR À

UN SYSTÈME DE 24V. INSTALLER LE CÂBLE AFIN QUE MISE EN GARDE IMPRIMÉE

SUR CÂBLE EST VISIBLE APRÈS L'INSTALLATION ET ATTACHER DES ÉTIQUETTES

DE MISE EN GARDE DE 24V (FOURNIS AVEC LE TRANSFORMATEUR 24V) SUR OU

LE LONG DE LA PISTE TOUS LES 4 PI.

RISK OF FIRE: DO NOT REMOVE REFLECTOR

RISQUE D'INCENDIE : NE RETIREZ PAS DE RÉFLECTEUR

ATTENTION-RISQUE D'INCENDIE MAX 18 WATT TYPE WEDGE T5

CAUTION-RISK OF FIRE MAX 18 WATT TYPE WEDGE T5

Figure 2 demonstrates fusing each indiviidual disk light, with a 9488 fused pluge