FXL SF & TRUN 0511 Installation Directions

102663-Installation 102663-Installation 102663-Installation 019813 Batch4 unilog cesco-content

102663-Installationsheet 102663-InstallationSheet 102663-InstallationSheet 019813 Batch4 unilog cesco-content

2016-08-16

: Pdf 144029-Installationsheet 144029-InstallationSheet B3 unilog

Open the PDF directly: View PDF .
Page Count: 4

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB ﬁ xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper

grounding is required for safety. This product must be installed in accordance with the applicable installation code by a

person familar with the construction and operations of the product and the hazards involved.

WARNING: Make certain power is OFF before installing or maintaining ﬁ xture.

FXL SF & TRUNNION INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting ﬁ xtures. Our aim is to design the best quality products to get the job done right. We’d

like to hear your comments. Call the Marketing Department at 888-RAB-1000, or email: marketing@rabweb.com

Slipﬁ tter Trunnion

SLIPFITTER MOUNTING

1. The slipﬁ tter ﬁ ts a 2 3/8” O.D. tenon. Place the slipﬁ t-

ter over the tenon and secure with the (2) Set Screws

on the side of the slipﬁ tter.

2. The angle of the ﬁ xture can be adjusted.

a. Remove (2) Cover Plate Screws and the Round

Cover Plate.

b. Loosen the Locking Bolt and swivel

the ﬁ xture.

c. Tighten the Locking Bolt and re-attach Round

Cover Plate.

TRUNNION MOUNTING

Adjust the angle of the ﬁ xture at the trunnion.

a. Loosen (2) Pivot Bolts and Angle Locking Screw.

b. Swivel the ﬁ xture.

c. Tighten the Pivot Bolts and Angle Locking Screw.

BEAM SPREAD ADJUSTMENT

WARNING: Make certain power is off.

The lamp socket can be moved from the standard beam

position to the rear position to provide a more narrow

beam or the front for a wider beam.

1. Remove (4) Reﬂ ector Screws.

2. Remove the Reﬂ ector from the ﬁ xture.

3. Loosen two socket nuts and slide socket into desired

position.

4. Tighten nuts. Replace Reﬂ ector in ﬁ xture and secure

with (4) Reﬂ ector Screws.

Reﬂ ector screws (4)

Reﬂ ector

Loosen these

2 nuts to

slide socket

FXL SF & TRUNNION INSTALLATION INSTRUCTIONS

ACCESSORIES

Wire Guard mounts with (4) stainless steel screws to

door as shown. Order separately, CAT# GDFXL.

Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during

installation, operation or maintenance.

TROUBLESHOOTING

Check that:

1. Proper lamp is installed. Lamp is not faulty.

2. Fixture is wired properly.

3. Line voltage at the ﬁ xture is correct.

4. Fixture is grounded properly.

LOCATION

1. Slipﬁ tter mounted ﬂ oodlight can be mounted on a

2 3/8” diameter pipe.

2. Trunnion mounted ﬂ oodlight can be mounted to a

ﬂ at surface.

3. Accessories are available for alternate installations.

LAMP INSTALLATION

CAUTION: Prior to installing, check that the lamp is

the correct ANSI type and wattage.

Observe lamp manufacturer’s recommendations on

lamp operation, ballast type and burn position.

1. Disconnect power. Make sure ﬁ xture and lamp are

cool enough to touch.

2. Open ﬁ xture by removing the (4) door screws. Swing

lens door down on hinges.

3. Insert lamp.

4. Before closing lens door make sure frame

gasket is properly seated all around ﬁ xture.

5. Close door. Tighten (4) screws.

CLEANING

Clean glass lens with nonabrasive glass

cleaning solution.

CAUTION: Be sure ﬁ xture temperature is cool

enough to touch. Do not clean or maintain while

ﬁ xture is engerized.

WIRING

All units are factory wired for 277V. If voltages other

than 277V are required, remove the reﬂ ector and rewire

for the appropriate voltage.

1. Connect the appropriate BLACK ﬁ xture lead to the

(+) LINE supply lead.

2. Connect the WHITE ﬁ xture lead to the (-) COMMON

supply lead.

3. Fixture ground wire must be connected to supply

ground.

4. All unused leads must be capped and insulated.

-*()5

'*9563&

-*/& #-"$,

$0..0/ 8)*5&

(306/% (306/%

REPLACEMENT LAMPS AND

BALLASTS

RAB Lamp ANSI RAB Ballast

Wattage Catalog# Code Catalog#

High Pressure Sodium

250 LHPS250 S50 BHPSH250QT

400 LHPS400 S51 BHPSH400QT

Metal Halide

175 LMH175MOG M57 BMHH175QT

200PS LMH200PS M136 BMHH200PSQ

250 LMH250 M58 BMHH250QT

250PS LMH250PS M153 BMHH250PSQ

320PS LMH320PS M154 BMHH320PSQ

350PS LMH350PS M131 BMHH350PSQ

400 LMH400Z M59 BMHH400QT

400PS LMH400PS M155 BMHH400PSQ

480V Ballasts are available, consult factory.

For 0˚ Up/Down Position

no changes required.

For 30˚ Up/Down Position

Follow 1-2-3

1. Before installing, open the lens frame, loosen the (4)

Reﬂ ector Screws and remove the reﬂ ector.

2. Remove the Wall Mount Bolts & Lockwashers

which secure the wall mount to the ﬁ xture.

3. Rotate the wall mount 180˚ and re-attach the Wall

Mount Bolts & Lockwashers. Replace the reﬂ ector.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB ﬁ xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper

grounding is required for safety. This product must be installed in accordance with the applicable

installation code by a person familiar with the construction and operations of the product and the hazards involved.

WARNING: Make certain power is OFF before installing or maintaining ﬁ xture.

FXL WALL MOUNT INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting ﬁ xtures. Our aim is to design the best quality products to get the job done right.

We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000, or email: marketing@rabweb.com

WALL MOUNTING OPTIONS

Wall Mount Bolts

& Lockwashers

Top Screws

Stainless

Steel Cable

Wall Feed Conduit Feed

Hardware

(not supplied)

Wall Mounting

Box

MOUNTING TO A WALL

1. Feed supply wires through Wall Mounting Box.

Orient box so that “TOP” is on top.

2. Secure Wall Mounting Box to a sturdy wall. Use

appropriate mounting hardware such as lag bolts

and anchors with washers suitable for the mounting

surface.

3. Bring ﬁ xture up to the Wall Mounting Box and slide

the stainless steel cable from the ﬁ xture into the key

hole slot for hands free wiring.

4. Wire the ﬁ xture using UL approved wire

connectors.

5. Place wired ﬁ xture over the Wall Mounting Box

and tighten the Top Screws. Now tighten the lower

screws.

6. Apply sealant to all unused conduit entry points.