2.2.2.4 Packet Tracer Configuring IPv4 Static And Routes Instructions
2.2.2.4%20Packet%20Tracer%20-%20Configuring%20IPv4%20Static%20and%20Default%20Routes%20Instructions
2.2.2.4%20Packet%20Tracer%20-%20Configuring%20IPv4%20Static%20and%20Default%20Routes%20Instructions
User Manual: Pdf
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
Packet Tracer - Configuring IPv4 Static and Default Routes Topology Addressing Table Device Interface IPv4 Address Subnet Mask Default Gateway G0/0 172.31.1.1 255.255.255.128 N/A S0/0/0 172.31.1.194 255.255.255.252 N/A G0/0 172.31.0.1 255.255.255.0 N/A S0/0/0 172.31.1.193 255.255.255.252 N/A S0/0/1 172.31.1.197 255.255.255.252 N/A G0/0 172.31.1.129 255.255.255.192 N/A R3 S0/0/1 172.31.1.198 255.255.255.252 N/A PC1 NIC 172.31.1.126 255.255.255.128 172.31.1.1 PC2 NIC 172.31.0.254 255.255.255.0 172.31.0.1 PC3 NIC 172.31.1.190 255.255.255.192 172.31.1.129 R1 R2 Objectives Part 1: Examine the Network and Evaluate the Need for Static Routing Part 2: Configure Static and Default Routes Part 3: Verify Connectivity © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 4 Packet Tracer - Configuring IPv4 Static and Default Routes Background In this activity, you will configure static and default routes. A static route is a route that is entered manually by the network administrator to create a reliable and safe route. There are four different static routes that are used in this activity: a recursive static route, a directly attached static route, a fully specified static route, and a default route. Part 1: Examine the Network and Evaluate the Need for Static Routing a. Looking at the topology diagram, how many networks are there in total? b. How many networks are directly connected to R1, R2, and R3? c. How many static routes are required by each router to reach networks that are not directly connected? d. Test connectivity to the R2 and R3 LANs by pinging PC2 and PC3 from PC1. Why were you unsuccessful? Part 2: Configure Static and Default Routes Step 1: Configure recursive static routes on R1. a. What is recursive static route? b. Why does a recursive static route require two routing table lookups? c. Configure a recursive static route to every network not directly connected to R1, including the WAN link between R2 and R3. d. Test connectivity to the R2 LAN and ping the IP addresses of PC2 and PC3. Why were you unsuccessful? Step 2: Configure directly attached static routes on R2. a. How does a directly attached static route differ from a recursive static route? b. Configure a directly attached static route from R2 to every network not directly connected. c. Which command only displays directly connected networks? d. Which command only displays the static routes listed in the routing table? e. When viewing the entire routing table, how can you distinguish between a directly attached static route and a directly connected network? © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 4 Packet Tracer - Configuring IPv4 Static and Default Routes Step 3: Configure a default route on R3. a. How does a default route differ from a regular static route? b. Configure a default route on R3 so that every network not directly connected is reachable. c. How is a static route displayed in the routing table? Step 4: Document the commands for fully specified routes. Note: Packet Tracer does not currently support configuring fully specified static routes. Therefore, in this step, document the configuration for fully specified routes. a. Explain a fully specified route. b. Which command provides a fully specified static route from R3 to the R2 LAN? c. Write a fully specified route from R3 to the network between R2 and R1. Do not configure the route; just calculate it. d. Write a fully specified static route from R3 to the R1 LAN. Do not configure the route; just calculate it. Step 5: Verify static route configurations. Use the appropriate show commands to verify correct configurations. Which show commands can you use to verify that the static routes are configured correctly? Part 3: Verify Connectivity Every device should now be able to ping every other device. If not, review your static and default route configurations. © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 3 of 4 Packet Tracer - Configuring IPv4 Static and Default Routes Suggested Scoring Rubric Activity Section Part 1: Examine the Network and Evaluate the Need for Static Routing Part 2: Configure Static and Default Routes Question Location Possible Points a-d 10 Part 1 Total 10 Step 1 7 Step 2 7 Step 3 3 Step 4 10 Step 5 3 Part 2 Total 30 Packet Tracer Score 60 Total Score 100 © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Earned Points Page 4 of 4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Tagged PDF : Yes Signing Date : 2013:07:14 14:02:07-07:00 Signing Authority : ARE Acrobat Product v8.0 P23 0002337 Document Usage Rights : FullSave Annotation Usage Rights : Create, Delete, Modify, Copy, Import, Export Form Usage Rights : Add, FillIn, Delete, SubmitStandalone Signature Usage Rights : Modify XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2013:07:14 13:52:08-07:00 Creator Tool : Microsoft® Word 2010 Modify Date : 2013:07:14 14:02:07-07:00 Metadata Date : 2013:07:14 14:02:07-07:00 Format : application/pdf Creator : Allan Producer : Microsoft® Word 2010 Document ID : uuid:1f6d3053-4ae0-4b4e-9dfc-ec92206328b6 Instance ID : uuid:0f1f81d2-d660-44b3-a565-a0ec5826fd73 Has XFA : Yes Page Count : 4 Language : en-US Author : AllanEXIF Metadata provided by EXIF.tools