2.2.5.5 Packet Tracer Configuring Floating Static Routes Instructions
2.2.5.5%20Packet%20Tracer%20-%20Configuring%20Floating%20Static%20Routes%20Instructions
2.2.5.5%20Packet%20Tracer%20-%20Configuring%20Floating%20Static%20Routes%20Instructions
User Manual: Pdf
Open the PDF directly: View PDF 
.
Page Count: 3
| Download | |
| Open PDF In Browser | View PDF |
Packet Tracer - Configuring Floating Static Routes Topology Objectives Part 1: Configure an IPv4 Floating Static Route Part 2: Test Failover to the IPv4 Floating Static Route Part 3: Configure and Test Failover for an IPv6 Floating Static Route Background In this activity, you will configure IPv4 and IPv6 floating static routes. These routes are manually configured with an administrative distance greater than that of the primary route and, therefore, would not be in the routing table until the primary route fails. You will test failover to the backup routes, and then restore connectivity to the primary route. Part 1: Configure an IPv4 Floating Static Route Step 1: Configure an IPv4 static default route. a. Configure a directly connected static default route from Edge_Router to the Internet. The primary default route should be through ISP1. b. Display the contents of the routing table. Verify that the default route is visible in the routing table. c. What command is used to trace a path from a PC to a destination? 255.255.255.255 From PC-A, trace the route to the Web Server. The route should start at the default gateway 192.168.10.1 and go through the 10.10.10.1 address. If not, check your static default route configuration. Step 2: Configure an IPv4 floating static route. a. What is the administrative distance of a static route? 255.255.255.255 b. Configure a directly connected floating static default route with an administrative distance of 5. The route should point to ISP2. c. View the running configuration and verify that the IPv4 floating static default route is there, as well as the IPv4 static default route. © 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 3 Packet Tracer - Configuring Floating Static Routes d. Display the contents of the routing table. Is the IPv4 floating static route visible in the routing table? Explain 255.255.255.255 Part 2: Test Failover to the IPv4 Floating Static Route a. On Edge_Router, administratively disable the exit interface of the primary route. b. Verify that the IPv4 floating static route is now in the routing table. c. Trace the route from PC-A to the Web Server. Did the backup route work? If not, wait a few more seconds for convergence and then re-test. If the backup route is still not working, investigate your floating static route configuration. d. Restore connectivity to the primary route. e. Trace the route from PC-A to the Web Server to verify that the primary route is restored. Part 3: Configure and Test Failover to an IPv6 Floating Static Route Step 1: Configure an IPv6 floating static route. a. The IPv6 static default route to ISP1 is already configured. Configure an IPv6 floating static default route with an administrative distance of 5. The route should point to IPv6 address (2001:DB8:A:2::1) of ISP2. b. View the running configuration to verify that the IPv6 floating static default route is now listed under the IPv6 static default route. Step 2: Test Failover to the IPv6 Floating Static Route. a. On Edge_Router, administratively disable the exit interface of the primary route. b. Verify that the IPv6 floating static route is now in the routing table. c. Trace the route from PC-A to the Web Server. Did the backup route work? If not, wait a few more seconds for convergence and then re-test. If the backup route is still not working, investigate your floating static route configuration. d. Restore connectivity to the primary route. e. Trace the route from PC-A to the Web Server to verify that the primary route is restored. © 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 3 Packet Tracer - Configuring Floating Static Routes Suggested Scoring Rubric Activity Section Part 1: Configuring a Floating Static Route Question Location Possible Points Step 1c 2 Step 2a 3 Step 2d 5 Part 1 Total 10 Packet Tracer Score 90 Total Score 100 © 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Earned Points Page 3 of 3
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : Betty Staerk Company : Microsoft Create Date : 2016:06:21 14:02:31-07:00 Modify Date : 2016:06:21 14:11:42-07:00 Source Modified : D:20160621210226 Has XFA : No Language : EN-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2016:06:21 14:11:42-07:00 Creator Tool : Acrobat PDFMaker 11 for Word Document ID : uuid:80621510-96fa-4d0e-8f0e-b72811ef89cc Instance ID : uuid:1de82e73-02fa-4b52-ab00-a2790e709852 Subject : 3 Format : application/pdf Creator : Betty Staerk Producer : Adobe PDF Library 11.0 State : 1 Version : 1.1 Page Layout : OneColumn Page Count : 3EXIF Metadata provided by EXIF.tools