Data Sheet DB EN MINI DC UPS/24DC/2
384947-Attachment 384947-Attachment 384947-Attachment 012596 Batch5 unilog cesco-content
298204-Attachment 298204-Attachment 298204-Attachment 012596 Batch5 unilog cesco-content
2014-07-04
: Pdf 298206-Attachment 298206-Attachment 012596 Batch5 unilog
Open the PDF directly: View PDF 
.
Page Count: 9
| Download | |
| Open PDF In Browser | View PDF |
MINI-DC-UPS/24DC/2
Uninterruptible power supply
INTERFACE
Data Sheet
103123_00_en
© PHOENIX CONTACT - 01/2007
Description
Especially compact and easy-to-use, the new MINI-DC-UPS/
24 DC/2 is a combination of the power supply unit and an uninterruptible power supply in the conventional ME housing. It
secures the operation of all connected 24 V consumers in the
electrical systems both in the case of an error-free supply
network and in the event of mains interferences.
The combined solution enables a slim design with dimensions of 67.5 x 99 x 107 mm. The wide-range input allows input
voltages between 85 V AC and 264 V AC; 2 A is provided at
the output with a regulated and adjustable output voltage
between 22.5 V DC and 29.5 V DC. The rechargeable battery module supplies an output voltage between 27.9 V DC
and 19.2 V DC in the buffer mode. A 0.8 Ah or a 1.3 Ah rechargeable battery module is used depending on the required buffer time: The module thus supplies 2 A for five minutes with the 0.8 Ah rechargeable battery module or 2 A for
30 minutes with the 1.3 Ah rechargeable battery module. The
buffer time varies depending on the load current.
The system availability is increased using extensive signaling through control lamps and active switching outputs. The
charging process of the rechargeable battery module, the
operational readiness, the buffer mode and the alarm messages are displayed before the rechargeable battery module
is discharged. The service life of the rechargeable battery
module can be increased by optimum battery management;
for example, a temperature-compensated charging protects
the rechargeable battery module at high ambient temperatures. An integrated timeout minimizes installation costs considerably.
Danger!
Components with dangerously high voltage and high stored energy are located in the device!
Never carry out work on live parts!
Depending on the ambient temperature and the load, the housing can become very hot!
Make sure you always use the the latest documentation.
It can be downloaded at www.download.phoenixcontact.com.
A conversion table is available on the Internet at
www.download.phoenixcontact.com/general/7000_en_00.pdf.
MINI-DC-UPS/24DC/2
Order data
Description
Type
Order No.
Pcs./Pkt.
Uninterruptible power supply
MINI-DC-UPS/24DC/2
2866640
1
Accessories
Type
Order No.
Pcs./Pkt.
Battery module, 24 V DC, 0.8 Ah
MINI-BAT/24DC/0.8AH
2866666
1
Battery module, 24 V DC, 1.3 Ah
MINI-BAT/24DC/1.3AH
2866417
1
Technical data
Input data
Input nominal voltage range
100 V AC ... 240 V AC
AC input voltage range
85 V AC ... 264 V AC
DC input voltage range
100 V DC ... 350 V DC
Buffer period
(settable: 0.5 min; 1 min; 2 min; 3 min; 5 min; 10 min; 15 min; 20 min; 30 min;
continuous)
Current consumption
Approx. 0.6 A (230 V AC)
Approx. 1.1 A (115 V AC)
Inrush current limitation/I2t
< 34 A (< 1.1 A2s)
Power failure bypass
(refer to the diagram)
Typical response time
100 ms
Power factor (cos phi)
Approx. 0.5
Protective circuitry
Varistor
Input fuse, integrated
3.15 A (slow-blow, internal)
Output data
Nominal output voltage
24 V DC
Setting range of the output voltage
22.5 V DC ... 29.5 V DC (normal mode; in the buffer mode, dependent on a battery voltage of 27.9 V DC ... 19.2 V DC)
Output current
2A
Derating
From +60°C 2.5% per Kelvin
Output current limit
Max. 3 A
Max. capacitive load
Unlimited
Control deviation
< 1 % (change in load, static 10% ... 90%)
Power loss
Max 2,5 W (buffer mode)
Power loss nominal load max.
15 W
Maximum power dissipation idling
3.8 W
Efficiency
> 82 % (typical)
Ascent time
< 100 ms
Residual ripple
< 50 mVPP
Peak switching voltages
< 100 mVPP
Connection in parallel
Yes, for redundancy
Surge protection against internal surge voltages
Yes, < 35 V DC
Resistance to reverse feed
35 V DC
Signal output Power OK
Status display
103123_00_en
Green LED (Power OK: LED permanently lit)
PHOENIX CONTACT
2
MINI-DC-UPS/24DC/2
Signal output Alarm
Output description
Relay output
Continuous current
200 mA
Output voltage
24 V
Status display
LED red (malfunction/alarm: LED permanently lit)
Signal output Battery charge
Output description
Relay output
Continuous current
200 mA
Output voltage
24 V
Status display
Yellow LED (Battery charge/battery is being charged: LED flashing)
Signal output Battery mode
Output description
Relay output
Continuous current
200 mA
Output voltage
24 V
Status display
Yellow LED (Battery mode/buffer mode: LED permanently lit)
Standards
Electrical Equipment for Machinery
EN 60204
Safety transformers for power supply units
EN 61558-2-17
Electrical safety (of information technology equipment)
EN 60950/VDE 0805 (SELV)
UL/C-UL recognized UL 60950
Industrial control equipment
UL/C-UL Listed UL 508
Electronic equipment for use in electrical power installations
EN 50178/VDE 0160 (PELV)
SELV
EN 60950 (SELV)
EN 60204 (PELV)
Safe isolation
DIN VDE 0100-410
DIN VDE 0106-1010
Protection against electric shock, basic requirements for safe isolation in
electrical equipment
DIN VDE 0106-101
General data
Insulation voltage input/output
2 kV (routine test)
4 kV (type test)
Installation position
Horizontal DIN rail NS 35, EN 60715
Degree of protection
IP20
Class of protection
II
MTBF
> 500 000 h in acc. with IEC 61709 (SN 29500)
Housing version
Polyamide PA, color: green
Width
67,5 mm
Height
99 mm
Depth
107 mm
Weight
0.45 kg
103123_00_en
PHOENIX CONTACT
3
MINI-DC-UPS/24DC/2
Climatic data
Ambient temperature (operation)
-25 °C ... 70 °C (> 60°C derating)
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Max. permissible relative humidity (operation)
95 % (at 25°C, no condensation)
Vibration (operation)
< 15 Hz, amplitude ±2.5 mm in acc. with IEC 60068-2-6
15 Hz ... 150 Hz, 2.3g, 90 min.
Shock
30g in all directions in acc. with IEC 60068-2-27
Pollution degree in acc. with EN 50178
2
Climatic class
3K3 (in acc. with EN 60721)
Conformance with EMC directive 89/336/EEC
Immunity to interference in acc. with EN 61000-6-2
Discharge of static electricity in acc. with EN 61000-4-2
Housing
Level 3
Contact discharge
6 kV
Discharge in air
8 kV
Comments
Criterion B
Electromagnetic HF field in acc. with EN 61000-4-3
Housing
Level 3
Frequency range
80 MHz ... 2 GHz
Field intensity
10 V/m
Comments
Criterion A
Fast transients (burst) in acc. with EN 61000-4-4
Input
4 kV (level 4 - asymmetrical: conductor to ground)
Output
2 kV (level 3 - asymmetrical: conductor to ground)
Signal
1 kV (level 2 - asymmetrical: conductor to ground)
Comments
Criterion B
Surge voltage capacities (surge) in acc. with EN 61000-4-5
Input
4 kV (level 4 - asymmetrical: conductor to ground)
2 kV (level 4 - symmetrical: conductor to conductor)
Output
2 kV (Level 3 - asymmetrical)
Signal
2 kV (Level 3 - asymmetrical)
Comments
Criterion B
1 kV (Level 3 - symmetrical)
Conducted disturbance in acc. with EN 61000-4-6
Input/Output/Signal
Level 3
Frequency range
10 kHz ... 80 MHz
Voltage
10 V
Comments
Criterion A
Emitted interference in acc. with EN 61000-6-3
Radio interference voltage in acc. with EN 55011
EN 55011 (EN 55022) Class B, area of application: Industry and residential
Emitted radio interference in acc. with EN 55011
EN 55011 (EN 55022) Class B, area of application: Industry and residential
Note:
Criterion A: Normal operating behavior within the defined limits.
Criterion B: Temporary impairment to operational behavior that is corrected by the device itself
EN 55011 corresponds to CISPR11 / EN 55022 corresponds to CISPR22
EN 61000 corresponds to IEC 1000
103123_00_en
PHOENIX CONTACT
4
MINI-DC-UPS/24DC/2
Block diagram
t...[min]
Remote
On/Off
R1
R2
Alarm
Bat. Mode
Charge
Battery
L(+)
PS
N(-)
+24 V/2A
Structure
2 4
5
"
O
U
T
D
C
2
4
V
2
e
h
C
t.
a
B
e
tt
a
B
2
R e
t
1 o F
R em F
O N
R
O
10
15
8,5
-2
,5 DC
22 V
5
B
a
a
t.
rg
-
3
e
M
0
30 2
o
2
d
]
A
in
la
[m
ax
1
0,5
rm
A
tm
7
6
8
3
ry
A
la
rm
K
ve
O
O
in
e
er
rg
ow
ha
e
-C
od
at.
P
9
-M
B
at.
B
rlo
S
P
-U
C
ID
IN
M
ad
V
0
4
2
- -)
0 (
0 N
1
C
A +)
(
IN L
1
0
INPUT
-25
AC input
DC output
Rechargeable battery connection
Active relay output: Alarm
Active relay output: Battery mode
Active relay output: Battery charge
Potentiometer 22.5 V DC ... 29.5 V DC
Remote shutdown (R1, R2)
Red control lamp: Alarm
Yellow control lamp: Battery mode/ Battery charge
Green control lamp: Power In OK / Overload
Buffer time setting 0.5 min ... 30 min and continuous
-25 ... + 70°C
-13 ... + 158°F
INFORMATION
TECHNOLOGY
US EQUIPMENT
(>60°C/+140°F Derating)
C
Read installation instructions
before connecting to mains
!
www.interface.phoenixcontact.com
TEMPERATURE
Power Supply
!
INDUSTRIAL
US CONTROL
EQUIPMENT
LISTED
43KA
UL
APPROVALS
C
MINI-DC-UPS/24DC/2
Order-No.: 28 66 64 0
OUTPUT
DC:
100-350V
0.8-0.2A
DC:
AC:
24V
100-240V~
2A
50-60Hz
Range:
85-264V~
1.55-0.5A
!
1
2
3
4
5
6
7
8
9
10
11
12
Input
Output
Signal
[mm2]
solid
stranded
0.2 - 2.5 0.2 - 2.5
0.2 - 2.5 0.2 - 2.5
0.2 - 2.5 0.2 - 2.5
AWG
24 - 12
24 - 12
14 - 24
[Nm]
Torque
0.5 - 0.6
0.5 - 0.6
0.5 - 0.6
Input data
Input nominal voltage range
100 V AC ... 240 V AC
AC input voltage range
85 V AC ... 264 V AC
DC input voltage range
100 V DC ... 350 V DC
Input fuse, integrated
3.15 A (slow-blow, internal)
Type of connection
COMBICON screw/plug connection
Stripping length
8 mm
Output data
Nominal output voltage
24 V DC
Setting range of the output voltage
22.5 V DC ... 29.5 V DC (normal mode; in the buffer mode, dependent on a
battery voltage of 27.9 V DC ... 19.2 V DC)
Output current
2A
Type of connection
COMBICON screw/plug connection
Stripping length
8 mm
103123_00_en
PHOENIX CONTACT
5
MINI-DC-UPS/24DC/2
Safety and warning notes
The power supply units are built-in devices. The device may only be installed and put into operation by qualified personnel. The corresponding national regulations (e.g. VDE, DIN) must be observed.
Danger!
Components with dangerously high voltage and high stored energy are located in the device!
Never carry out work on live parts!
Depending on the ambient temperature and the load, the housing can become very hot!
Before startup please ensure:
The mains connection has been carried out by a competent person and protection against electric
shock is guaranteed!
All feed lines are sufficiently protected and dimensioned!
All output lines are dimensioned according to the maximum output current of the device or separately
protected!
Sufficient convection is guaranteed!
Installation
In order for the device to function in the manner intended. it is not necessary to observe
any minimum spacing to other devices.
The power supply unit can be snapped onto all
DIN rails in acc. with EN 60715. They must be
horizontal (connecting terminal blocks above
and below).
Installation position
Assembly
Position the module with the DIN rail guide on the upper edge
of the DIN rail, and snap it in with a downward motion.
Dismantling
Pull the snap lever open with the aid of a screwdriver and
slide the module out at the lower edge of the DIN rail.
103123_00_en
PHOENIX CONTACT
6
MINI-DC-UPS/24DC/2
Connection, network forms 100...240 V AC networks
TN-S
TN-C
L
N
PE
L N
TT
L
PEN
L N
+ -
+ -
The 100...240 V AC connection is made using the L and N
screw connections.
The device can be connected to 1-phase AC networks or to
two of the phase conductors of three-phase systems (TN, TT
or IT networks in acc. with VDE 0100-300/IEC 60364-3) with
nominal voltages of 100 V AC ...240 V AC.
iT
L1
L2
L3
L
N
L N
+ -
L N
+ -
For operation on two of the phase conductors
of a three-phase system, an isolating facility for
all poles must be provided.
Input
O
The 100-...240 V AC connection is established using the L
and N screw connections.
U
T
D
C
2
4
V
2
rm
A
e
B
h
C
t.
a
B
e
tt
a
B
2
R e
t
1 o F
R em F
O N
R
O
10
15
8,5
-2
,5 DC
22 V
5
The device must be installed in acc. with the regulations as
in EN 60950. It must be possible to disconnect the device
using a suitable isolating facility outside the power supply.
The primary side line protection, for example, is suitable. For
device protection, there is an internal fuse. Additional device
protection is not necessary.
a
a
t.
rg
-
3
e
M
0
30 2
o
2
d
]
A
in
la
[m
1
0,5
ax
tm
ry
A
la
rm
B
K
ve
O
O
in
e
er
rg
ow
ha
e
P
-C
od
at.
-M
B
at.
rlo
S
P
-U
C
ID
IN
M
ad
V
0
4
2
- -)
0 (
0 N
1
C
A +)
(
IN L
1
INPUT
!
-25
-25 ... + 70°C
-13 ... + 158°F
INFORMATION
TECHNOLOGY
US EQUIPMENT
(>60°C/+140°F Derating)
C
Read installation instructions
before connecting to mains
!
www.interface.phoenixcontact.com
INDUSTRIAL
US CONTROL
EQUIPMENT
LISTED
43KA
UL
TEMPERATURE
Power Supply
C
APPROVALS
MINI-DC-UPS/24DC/2
Order-No.: 28 66 64 0
OUTPUT
DC:
100-350V
0.8-0.2A
DC:
AC:
24V
100-240V~
2A
50-60Hz
Range:
85-264V~
1.55-0.5A
103123_00_en
If an internal fuse is triggered, there is most
probably a malfunction in the device. In this
case, the device must be inspected in the
factory!
PHOENIX CONTACT
7
MINI-DC-UPS/24DC/2
Output
DC output
O
Active switching
outputs
U
T
D
C
2
4
V
2
rm
A
e
h
C
t.
a
B
e
tt
a
B
2
R e
t
1 o F
R em F
O N
R
O
10
15
8,5
-2
,5 DC
22 V
5
B
a
a
t.
rg
-
3
e
M
0
30 2
o
2
d
]
A
in
la
[m
1
0,5
ax
tm
ry
A
e
K
ve
O
O
in
e
er
rg
ow
ha
P
-C
od
at.
-M
B
at.
rm
la
B
rlo
M
IN
ID
C
-U
P
S
ad
V
0
4
2
- -)
0 (
0 N
1
C
A +)
(
IN L
INPUT
-25
-25 ... + 70°C
-13 ... + 158°F
INFORMATION
TECHNOLOGY
US EQUIPMENT
(>60°C/+140°F Derating)
C
Read installation instructions
before connecting to mains
!
www.interface.phoenixcontact.com
TEMPERATURE
Power Supply
!
INDUSTRIAL
US CONTROL
EQUIPMENT
LISTED
43KA
UL
APPROVALS
C
MINI-DC-UPS/24DC/2
Order-No.: 28 66 64 0
OUTPUT
DC:
100-350V
0.8-0.2A
DC:
AC:
24V
100-240V~
2A
50-60Hz
Range:
85-264V~
1.55-0.5A
Control lamps
The connection is established through the "OUT DC 24 V, +, –" screw connections. The set output voltage is 24 V DC at
the time of delivery. The output voltage from 22.5 V DC to 29.5 V DC can be set on the potentiometer.
Signaling outputs
Signal outputs are connected using "Alarm", "Bat.-Mode" and "Bat.-Charge" terminal blocks. Three control lamps and three
active switching outputs are provided for function monitoring.
State
Power In OK
Battery mode/ Battery charge
Alarm
Supply voltage OK, rechargeable
battery is being charged
LED on
LED is flashing; Battery mode
output: 0 V, Battery charge: 24 V
LED off; output: 0 V
Supply voltage OK, rechargeable
battery charged (normal mode)
LED on
LED off; Battery mode / Battery
charge output: 0 V
LED off; output: 0 V
Buffer mode
LED off
LED on; Battery mode output: 24 V, LED off; output: 0 V
Battery charge: 0 V
Rechargeable battery discharged, LED off
UBAT < 20.4 V DC
LED on; Battery mode / Battery
charge output: 0 V
LED on; output: 24 V
Rechargeable battery test negative
LED on
LED off; Battery mode / Battery
charge output: 0 V
LED on; output: 24 V
Buffer time over and remote shut- LED off
down activated
LED off; Battery mode / Battery
charge output: 0 V
LED off; output: 0 V
103123_00_en
PHOENIX CONTACT
8
MINI-DC-UPS/24DC/2
Current [A]
Rechargeable battery module
The rechargeable battery module is connected to the power
supply unit through the "Battery +" and the "Battery –" terminal blocks. The fuse of the rechargeable battery module
must be removed when installing or replacing the module.
2
1,5
1,0
0,5
0
0
30
60
90
120
150
180
210
240
Buffer time[min]
MINI-BAT 24DC/0,8Ah
MINI-BAT 24DC/1,3Ah
The following rechargeable battery modules are recommended:
MINI-BAT 24DC/0.8Ah (order no. 2866666),
MINI-BAT 24DC/1.3Ah (order no. 2866417)
The buffer mode might be terminated after the preset time or
due to an external shutdown. If the device is to be switched
off after a certain period, the time for it is set using the selector switch at the front of the device. The device can be switched on in the buffer mode again after reconnecting the
power supply.
Remote shutdown ("Remote")
The device has a remote shutdown with a UPS function for deliberate shutdown. Remote shutdown must be deactivated
for the device to switch over to the buffer mode in the event of a supply voltage failure.
Remote shutdown inactive
– The "Remote shutdown R1" and "Remote shutdown R2" terminal points are short-circuited (e.g. with a plug-in bridge)
OR 24 V DC is present at the "Remote shutdown R2" terminal point.
– The power supply unit switches over to the buffer mode in the event of a supply voltage failure.
Remote shutdown active
– The "Remote shutdown R1" and "Remote shutdown R2" terminal points are not short-circuited (e.g. with a plug-in bridge)
OR 0 V is present at the "Remote shutdown R2" terminal point.
- All LEDs are off.
– The power supply does not switch over to the buffer mode in the event of a supply voltage failure; the device switches
off. The rechargeable battery module is charged when the supply voltage is reconnected, but the device remains switched
off until the remote shutdown is activated.
– The connected consumers are fed as long as the supply voltage is available.
Function
Output voltage
In the normal mode, the output voltage of the device conforms to the setting on the potentiometer (22.5 V DC ... 29.5 V DC).
If the supply voltage fails, the buffer mode is activated without any interruption and the output voltage is supplied by the
rechargeable battery module. The output voltage is now directly dependent on the battery voltage and is UBAT - 0.5 V.
An alarm signal is triggered if the output voltage drops below 20.4 V in the buffer mode. If the output voltage drops to 19.2
V due to a completely discharged rechargeable battery module, the device switches off and remains switched off. The device switches on automatically only after reconnecting the power supply. The device is electronically protected against short
circuit and idling.
103123_00_en
PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany
Phone: +49-(0) 5235-3-00 • Fax: +49-(0) 5235-3-4 12 00
www.phoenixcontact.com
9
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Page Mode : UseOutlines XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Create Date : 2002:03:01 06:14:01Z Creator Tool : FrameMaker 7.1 Metadata Date : 2007:01:19 11:53:14+01:00 Modify Date : 2012:05:25 14:34:52+02:00 Format : application/pdf Title : Data Sheet DB EN MINI-DC-UPS/24DC/2 Creator : PHOENIX CONTACT GmbH & Co. KG Description : Uninterruptible power supply Document ID : uuid:0b74dad9-da19-4012-a47f-ffa607014eb7 Instance ID : uuid:31afd0e7-ad30-48fe-ab53-a702a473c6c5 Page Count : 9 Subject : Uninterruptible power supply Author : PHOENIX CONTACT GmbH & Co. KGEXIF Metadata provided by EXIF.tools