Material Safety Data Sheet (MSDS) 416030
2016-12-16
: Pdf 416030 416030 msds
Open the PDF directly: View PDF .
Page Count: 5
Page 1 of 5
Safety Data Sheet
1 - Identification
Trade Name: WD-40 Specialist® Dirt & Dust
Resistant Dry Lube
Chemical Name: Organic Mixture
Product Use: Cleaner, Lubricant
Restrictions on Use: None identified
SDS Date Of Preparation: 07/13/14
Manufacturer: WD-40 Company
Address: 1061 Cudahy Place (92110)
P.O. Box 80607
San Diego, California, USA
92138 –0607
Telephone:
Emergency only: 1-888-324-7596 (PROSAR)
Information: 1-888-324-7596
Chemical Spills: 1-800-424-9300 (Chemtrec)
1-703-527-3887 (International Calls)
2 – Hazards Identification
Hazcom 2012/GHS Classification:
Flammable Aerosol Category 1
Gas Under Pressure: Compressed Gas
Aspiration Toxicity Category 1
Skin Irritant Category 2
Specific Target Organ Toxicity Single Exposure Category 3 (nervous system effects)
Note: This product is a consumer product and is labeled in accordance with the US Consumer Product
Safety Commission regulations which take precedence over OSHA Hazard Communication labeling. The
actual container label will not include the label elements below. The labeling below applies to
industrial/professional products.
Label Elements:
DANGER!
Extremely Flammable Aerosol.
Contains gas under pressure; may explode if heated.
May be fatal if swallowed and enters airways.
Causes skin irritation.
May cause drowsiness or dizziness.
Prevention
Keep away from heat, sparks, open flames, hot surfaces – No smoking.
Do not spray on an open flame or other ignition source.
Pressurized container: Do not pierce or burn, even after use.
Avoid breathing vapors or mists.
Wash thoroughly with soap and water after handling.
Use only outdoors or in a well-ventilated area.
Wear protective gloves.
Response
IF SWALLOWED: Immediately call a POISON CENTER or physician. Do NOT induce vomiting.
IF ON SKIN: Wash with plenty of soap and water. If skin irritation occurs: Get medical attention. Take off
contaminated clothing and wash before reuse.
416030
Page 2 of 5
IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing. Call a POISON
CENTER or physician if you feel unwell.
Storage
Store locked up.
Protect from sunlight. Do not expose to temperatures exceeding 50°C/122°F. Store in a well-ventilated place.
Disposal
Dispose of contents and container in accordance with local and national regulations.
3 - Composition/Information on Ingredients
Ingredient
CAS #
Weight Percent
US Hazcom 2012/ GHS
Classification
Heptane
64742-49-0
142-82-5
70-80%
Aspiration Toxicity Category 1
Flammable Liquid Category 2
Skin Irritant Category 2
Specific Target Organ Toxicity
Single Exposure Category 3
(nervous system effects)
Propane Propellant
74-98-6
10-20%
Flammable Gas Category 1
Gas Under Pressure,
Compressed Gas
Petroleum Solvent
64741-66-8
64742-47-8
5-10%
Flammable Liquid, Category 2
Aspiration Toxicity Category 1
Mineral Oil
Proprietary
1-5%
Not Hazardous
Note: The exact percentages are a trade secret.
4 – First Aid Measures
Ingestion (Swallowed): Aspiration Hazard. DO NOT induce vomiting. Call physician, poison control center
or the WD-40 Safety Hotline at 1-888-324-7596 immediately.
Eye Contact: Flush thoroughly with water. Remove contact lenses if present after the first 5 minutes and
continue flushing for several more minutes. Get medical attention if irritation persists.
Skin Contact: Wash with soap and water. If irritation develops and persists, get medical attention.
Inhalation (Breathing): If irritation is experienced, move to fresh air. Get medical attention if irritation or other
symptoms develop and persist.
Signs and Symptoms of Exposure: Harmful or fatal if swallowed. If swallowed, may be aspirated and
cause lung damage. May cause eye and respiratory irritation. Inhalation may cause coughing, headache and
dizziness. Skin contact may cause drying of the skin.
Indication of Immediate Medical Attention/Special Treatment Needed: Immediate medical attention is
needed for ingestion.
5 – Fire Fighting Measures
Suitable (and unsuitable) Extinguishing Media: Use water fog, dry chemical, carbon dioxide or foam. Do
not use water jet or flooding amounts of water. Burning product will float on the surface and spread fire.
Specific Hazards Arising from the Chemical: Contents under pressure. Extremely flammable aerosol.
Extremely flammable liquid and vapor. Keep away from ignition sources and open flames. Exposure of
containers to extreme heat and flames can cause them to rupture often with violent force. Vapors can cause a
flash fire. Vapors are heavier than air and may travel along surfaces to remote ignition sources and flash
back. Combustion will produce oxides of carbon, smoke fumes, unburned hydrocarbons and small amounts of
hydrogen fluoride and carbonyl fluoride. A vapor and air mixture can create an explosion hazard in confined
spaces.
Special Protective Equipment and Precautions for Fire-Fighters: Firefighters should always wear positive
pressure self-contained breathing apparatus and full protective clothing. Cool fire-exposed containers with
water. Use shielding to protect against bursting containers.
Page 3 of 5
6 – Accidental Release Measures
Personal Precautions, Protective Equipment and Emergency Procedures: Wear appropriate protective
clothing (see Section 8). Eliminate all sources of ignition and ventilate area.
Methods and Materials for Containment/Cleanup: Leaking cans should be placed in a plastic bag or open
pail until the pressure has dissipated. Contain and collect liquid with an inert absorbent and place in a
container for disposal. Clean spill area thoroughly. Report spills to authorities as required.
7 – Handling and Storage
Precautions for Safe Handling: Avoid contact with eyes. Avoid prolonged contact with skin. Avoid breathing
vapors or aerosols. Use only with adequate ventilation. Keep away from heat, sparks, pilot lights, hot surfaces
and open flames. Unplug electrical tools, motors and appliances before spraying or bringing the can near any
source of electricity. Electricity can burn a hole in the can and cause contents to burst into flames. To avoid
serious burn injury, do not let the can touch battery terminals, electrical connections on motors or appliances
or any other source of electricity. Wash thoroughly with soap and water after handling. Keep containers
closed when not in use. Keep out of the reach of children. Do not puncture, crush or incinerate containers,
even when empty.
Conditions for Safe Storage: Store in a cool, well-ventilated area, away from incompatible materials Do not
store above 120F or in direct sunlight. U.F.C (NFPA 30B) Level 3 Aerosol. Store away from oxidizers.
8 – Exposure Controls/Personal Protection
Chemical
Occupational Exposure Limits
Heptane
500 ppm TWA OSHA PEL
400 ppm TWA, 500 ppm STEL ACGIH TLV
Propane Propellant
1000 ppm TWA OSHA PEL
Petroleum Solvent
1400 mg/m3 TWA Supplier Recommended (total hydrocarbon)
Mineral Oil
5 mg/m3 (inhalable) TWA
5 mg/m3 TWA OSHA PEL
The Following Controls are Recommended for Normal Consumer Use of this Product
Appropriate Engineering Controls: Use in a well-ventilated area.
Personal Protection:
Eye Protection: Avoid eye contact. Always spray away from your face.
Skin Protection: Avoid prolonged skin contact. Chemical resistant gloves recommended for operations
where skin contact is likely.
Respiratory Protection: None needed for normal use with adequate ventilation.
For Bulk Processing or Workplace Use the Following Controls are Recommended
Appropriate Engineering Controls: Use adequate general and local exhaust ventilation to maintain
exposure levels below that occupational exposure limits.
Personal Protection:
Eye Protection: Safety goggles recommended where eye contact is possible.
Skin Protection: Wear chemical resistant gloves.
Respiratory Protection: None required if ventilation is adequate. If the occupational exposure limits are
exceeded, wear a NIOSH approved respirator. Respirator selection and use should be based on contaminant
type, form and concentration. Follow OSHA 1910.134, ANSI Z88.2 and good Industrial Hygiene practice.
Work/Hygiene Practices: Wash with soap and water after handling.
9 – Physical and Chemical Properties
Appearance:
Clear liquid
Flammable Limits:
LEL: 0.9% UEL: 9.5%
Odor:
Pleasant odor
Vapor Pressure:
40-50 psi @ 70°F
Page 4 of 5
Odor Threshold:
Not established
Vapor Density:
Greater than 1 (air=1)
pH:
Not Applicable
Relative Density:
0.72
Melting/Freezing Point
Not established
Solubilities:
Insoluble in water
Boiling Point/Range:
90-140°C (194-284°F)
Partition Coefficient; n-
octanol/water:
Not established
Flash Point:
<-29.2°F Tag Closed
Cup
Autoignition
Temperature:
Not established
Evaporation Rate:
Not established
Decomposition
Temperature:
Not established
Flammability (solid, gas)
Flammable Aerosol
Viscosity:
Not established
VOC:
93.2%
Pour Point:
Not established
10 – Stability and Reactivity
Reactivity: Not reactive under normal conditions
Chemical Stability: Stable
Possibility of Hazardous Reactions: May react with strong oxidizers generating heat.
Conditions to Avoid: Avoid heat, sparks, flames and other sources of ignition. Do not puncture or incinerate
containers.
Incompatible Materials: Strong oxidizing agents.
Hazardous Decomposition Products: Carbon monoxide and carbon dioxide, smoke fumes, unburned
hydrocarbons and small amounts of hydrogen fluoride and carbonyl fluoride.
11 – Toxicological Information
Symptoms of Overexposure:
Inhalation: Mist or vapor can irritate the throat and lungs. High concentrations may cause nasal and
respiratory irritation and central nervous system effects such as headache, dizziness and nausea. Intentional
abuse may be harmful or fatal.
Skin Contact: May cause skin irritation with short-term exposure with redness, itching and burning of the
skin. Prolonged and/or repeated contact may produce defatting and possible dermatitis.
Eye Contact: Contact may be irritating to eyes. May cause redness, stinging, swelling and tearing.
Ingestion: This product has low oral toxicity. If swallowed, this material may cause irritation of the mouth,
throat and esophagus. Swallowing may cause gastrointestinal irritation, nausea, vomiting, diarrhea,
dizziness, drowsiness and other central nervous system effects. This product is an aspiration hazard. If
swallowed, can enter the lungs and may cause chemical pneumonitis, severe lung damage and death.
Chronic Effects: Prolonged or repeated skin contact may defeat the skin resulting in irritation and dermatitis.
Carcinogen Status: None of the components are listed as a carcinogen or suspect carcinogen by IARC,
NTP, ACGIH or OSHA.
Reproductive Toxicity: None of the components is considered a reproductive hazard.
Numerical Measures of Toxicity:
The oral toxicity of this product is estimated to be greater than 2,000 mg/kg and the dermal toxicity greater
than 2,000 mg/kg based on an assessment of the ingredients. This product is not classified as toxic by
established criteria. It is an aspiration hazard.
12 – Ecological Information
Ecotoxicity: Heptane: 24 hr LC50 Goldfish – 4 mg/L; 24 hr EC50 Daphnia magna – >10 mg/L
Petroleum Solvent: No ecotoxicity data available. Ingredient is expected to be toxic to the aquatic
environment with long-term adverse effects.
Persistence and Degradability: Component are not readily biodegradable.
Bioaccumulative Potential: Bioaccumulation is not expected based on an assessment of the ingredients.
Mobility in Soil: No data available
Other Adverse Effects: None known
13 - Disposal Considerations
Page 5 of 5
If this product becomes a waste, it would be expected to meet the criteria of a RCRA ignitable hazardous
waste (D001). However, it is the responsibility of the generator to determine at the time of disposal the proper
classification and method of disposal. Do not puncture or incinerate containers, even empty. Dispose in
accordance with federal, state, and local regulations.
14 – Transportation Information_
DOT Surface Shipping Description:
UN1950, Aerosols, 2.1 Ltd. Qty (Note: Shipping Papers are not required for Limited Quantities unless
transported by air or vessel – each package must be marked with the Limited Quantity Mark)
IMDG Shipping Description: Un1950, Aerosols, 2.1, LTD QTY Marine Pollutant (Heptane)
ICAO Shipping Description: UN1950, Aerosols, flammable, 2.1 NOTE: WD-40 does not test aerosol cans to
assure that they meet the pressure and other requirements for transport by air. We do not recommend that
our aerosol products be transported by air.
15 – Regulatory Information
CERCLA 103 Reportable Quantity: This product is not subject to CERCLA reporting requirements,
however, oil spills are reportable to the National Response Center under the Clean Water Act and many
states have more stringent release reporting requirements. Report spills required under federal, state and
local regulations.
SARA TITLE III:
Hazard Category For Section 311/312: Acute Health, Fire Hazard, Sudden Release of Pressure
Section 313 Toxic Chemicals: This product contains the following chemicals subject to SARA Title III
Section 313 Reporting requirements: None
Section 302 Extremely Hazardous Substances (TPQ): None
EPA Toxic Substances Control Act (TSCA) Status: All of the components of this product are listed on the
TSCA inventory
VOC Regulations: This product complies with the consumer product VOC limits of CARB, the US EPA and
states adopting the OTC VOC rules.
California Safe Drinking Water and Toxic Enforcement Act (Proposition 65): This product does not
contain chemicals regulated under California Proposition 65.
Canadian Environmental Protection Act: All of the ingredients are listed on the Canadian Domestic
Substances List or exempt from notification
Canadian WHMIS Classification: Class A (Compressed Gas), Class B-5 (Flammable Aerosol), Class D-2-B
(Toxic material causing other toxic effects)
This MSDS has been prepared according to the criteria of the Controlled Products Regulation (CPR) and the
MSDS contains all of the information required by the CPR.
16 – Other Information:
HMIS Hazard Rating:
Health – 1 (slight hazard), Fire Hazard – 4 (severe hazard), Physical Hazard – 0 (minimal hazard)
Revision Date: July 13, 2014 Supersedes: September 2012
Revision Summary: Convert to Hazcom 2012. Changes in all sections.
Prepared by: Industrial Health & Safety Consultants, Inc. Shelton, CT, USA
APPROVED BY: I.Kowalski Regulatory Affairs Dept.
2095100/No.0049703