Installation Directions

2014-05-16

: Pdf 45781-Installationsheet 45781-InstallationSheet 078477 Batch3 unilog

Open the PDF directly: View PDF .
Page Count: 2

WARNINGS AND CAUTIONS:

• ON/OFF LED for remote load status.

• To be installed and/or used in accordance with appropriate electrical codes and regulations.

• If you are unsure about any part of these instructions, consult a qualiﬁed electrician.

• Vizia RF +™ VRCZ4 remote does not control the load, but provides scene applications to operate with Vizia RF +TM dimmers/switches.

• Recommended minimum wall box depth is 2-1/2".

WARNINGS AND CAUTIONS:

• Can call up four (4) zone ON/OFF with advanced Programmer/Remote (see VRCPG).

• Disconnect power at circuit breaker or fuse when servicing, installing or removing ﬁxture.

• Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.

4-Zone Controller

Cat. No. VRCZ4

120VAC, 60Hz

INSTALLATION INSTRUCTIONS

DI-000-VRCZ4-00A-X0

/./&&

/./&&/./&&

/./&&

WARNING: TO AVOID FIRE, SHOCK OR DEATH; TURN

OFF POWER at circuit breaker or fuse and test that power is off

before wiring!

Step 1

Step 3 Preparing and connecting wires:

This 4-Zone controller can be wired using side wire terminal

screws or through backwire openings. Choose appropriate wire

stripping speciﬁcations accordingly.

• Make sure that the ends of the wires from the wall box are

straight (cut if necessary).

Side Wire Connection

Side wire terminals accept

#14 AWG solid wire copper only.

5/8"

(1.6 cm) Strip Gage

(measure bare

wire here)

Cut

(if necessary)

Back Wire (either hole may be used)

Back wire openings use #14-12 AWG

solid wire copper only.

WIRING SWITCH:

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot wall box wire to terminal screw marked "BK".

• Line Neutral wall box wire to terminal screw marked "WH".

Hot (Black)

Neutral (White)

Line

120VAC, 60Hz

BKWH

Green

Ground

4-Zone Controlller

Wiring Application:

Step 4

Identifying your wiring application (most common):

NOTE: If the wiring in your wall box does not resemble this

conﬁguration, consult a qualiﬁed electrician.

Step 2

INTRODUCTION

Leviton’s Vizia RF +TM components are designed to communicate

with each other via Radio Frequency (RF) to provide remote control

of your lighting. Using RF technology allows Leviton to provide the

greatest signal integrity possible. Each module in Leviton’s Vizia RF +TM

component line is a Z-Wave® enabled device. In a Z-Wave® network,

each device is designed to act as a router. These routers will re-transmit

the RF signal from one device to another until the intended device is

reached. This ensures that the signal is received by its intended device

by routing the signal around obstacles and radio dead spots. The 4-Zone

Controller is compatible with any Z-Wave® enabled network, regardless

of the manufacturer and can also be used with other devices displaying

the Z-Wave® logo.

• This is a Z-Wave® Controller

• Zone/Area control without traveler wires

• Can control ON/OFF dim/bright for up to 4 Zones/Area.

• ON/OFF LED

• Two way communication

• RF reliability

• Ease of installation – No new wiring

• Compatible with other Z-Wave® enabled devices

FEATURES

Tools needed to install your 4-Zone Controller:

Slotted/Phillips Screwdriver Electrical Tape Pliers

Pencil Cutters Ruler

Changing the color of your 4-Zone Controller:

Your 4-Zone controller includes three color options. The controller ships

with the White frame attached. To change color of frame, proceed as

follows:

Line up tabs

and press in

side to attach

Push in

side at tab

to release

After frame is removed, remove existing push buttons by pressing out

buttons from back of frame and replace them with desired color change

push buttons by pressing in from front of frame. To make IR capable, use

new DIM/BRIGHT button with IR window.

INSTALLING YOUR 4-ZONE CONTROLLER

NOTE: Use check boxes when Steps are completed.

• Restore power at circuit breaker or fuse.

• LED should turn ON, when any button is pressed. If LED does not turn

ON, refer to the TROUBLESHOOTING section.

• Position all wires to provide room in

outlet wall box for device.

• Ensure that the word “TOP” is facing up

on device strap.

• Partially screw in mounting screws in

wall box mounting holes.

NOTE: Dress wires with a bend as

shown in diagram in order to relieve

stress when mounting device.

Testing your 4-Zone Controller prior to mounting

in wall box:

Step 5

1. Line (Hot)

2. Neutral

3. Ground

Step 6 4-Zone Controller Mounting:

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.

Installation may now be completed by

tightening mounting screws into wall box.

Attach wallplate.

Restore Power:

Restore power at circuit breaker or fuse.

Installation is complete.

Step 7

NOTES:

• If using a non-Leviton Programmer/Remote, refer to the

Programmer/Remote instruction sheet.

• 4-Zone controllers incuded into a Z-Wave® network must be updated

after you have included all other devices.

• If using VRCPG install checklist go directly to step B.

A) If using a Leviton Z-Wave® Programmer/Remote, Cat. No. VRCPG,

press the Menu button and scroll down to System Setup. Press

the center button to select System Setup Menu. Choose Advance

Settings. Press the center button to select Network. Press the center

button to <Include Node>.

B) If using VRCPG Programmer/Remote, you will be prompted to place

4-Zone controller into programming mode.

C) To access Program mode, press and hold the

left side of buttons 1 and 3 (refer to ﬁgure).

Wait 5 seconds until the LED turns Amber.

Release the button and the LED will blink

Amber. You are now in Programming mode.

NOTE: If the LED on the 4-Zone controller

turns solid Red while including, there has

been a communication error.

D) While standing close to the 4-Zone controller

(approximately 1 foot), press the center button

on the Programmer/Remote to <Include>

device in the network.

NOTE: Only one device may be included at

any time.

NOTE: If the LED on the 4-scene controller turns solid Red while

including, there has been a communication error.

E) The Primary Programmer/Remote will assign a Home ID, Node ID,

and Name for this device.

NOTE: This information will be stored in the Programmer/Remote to

be used for future reference.

NOTE: You may name or edit the node of this device at this time.

F) The 4-Zone controller is now installed in the network.

Including 4-Zone Controller into Z-Wave®

Network:

Step 8

DI-000-VRCZ4-00A-X0

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the beneﬁt of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for ﬁve years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement,

at its option, if within such ﬁve year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability

for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or

implied warranties of any kind, including merchantability and ﬁtness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and ﬁtness for a particular purpose, is limited to ﬁve years. Leviton is not liable for incidental,

indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or proﬁts or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

Step 8 cont'd

Programmer/Remote

Cat. No. VRCPG

NOTE: Programmer/Remote must be

in close proximity to 4-Zone controller

when including in the network.

For additional information, contact Leviton’s

Techline at 1-800-824-3005 or visit Leviton’s

website at www.ViziaRF+.com

Protected under U.S. Patent Number 6,388,399 and patents pending and

licensed under U.S. Patents Numbers 5,905,442, and 5,982,103

This equipment has been tested and found to comply with the limits for

a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment OFF and ON, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving Antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/tv technician for help.

FCC COMPLIANCE STATEMENT

Including 4-Zone Controller into

Z-Wave® Network:

TROUBLESHOOTING

• Locator LED on controller does not turn ON

- Circuit breaker or fuse has tripped.

- If 4-Zone controller is powered up and LED does not turn ON, check

wiring.

• Zone Controller does not operate lights

- Check association.

- Ensure that controller was properly updated.

If LED turns solid red

- Check association.

- Ensure that each device in the network is with in 70 ft (21 m) of another

device.

•

Push Button (Default settings)

Turn ON from OFF position:

Press left side of button – Turns all lights in

Zone/Area ON, LED turns ON.

LED will blink until Zone/Area is ON.

Turn OFF from ON position:

Press right side of button – Turns all lights in

Zone/Area OFF, LED turns OFF.

Dim/Bright:

Press left side of Dim/Bright button - Lights in

last activated Zone/Area will dim.

Press right side of Dim/Bright button - Lights in

last activated Zone/Area will brighten.

NOTE: Controller will only Dim/Bright devices

located within direct Radio Frequency range.

NOTE: LED will be lit Green if any one load in

the associated Area is ON. LED will be OFF

when all loads are turned OFF.

If there is a power outage, when the power is

restored, the lights will return to the last setting

before the power interruption.

Cleaning: Clean with a damp cloth.

DO NOT use chemical cleaners.

OPERATION

Locator

LED

Push

Buttons

Dim/Bright

Button

A) If using a Leviton Z-Wave® Programmer/Remote, Cat. No. VRCPG,

press the Menu button and scroll down to System Setup. Press the

center button to select System Setup Menu. Choose Advance Settings.

Press the center button to select Network. Scroll down to <Exclude

Node> and press the center button.

B) If using VRCPG Programmer/Remote, you will be prompted to place

4-Zone controller into programming mode.

C) To access Program mode, press and hold the left side of buttons 1 and

3 (refer to ﬁgure). Wait 5 seconds until the LED turns Amber. Release

the buttons and the LED will blink Amber. You are now in Programming

mode.

NOTE: If the LED on the 4-Zone controller turns solid Red while

excluding, there has been a communication error.

D) While standing close to the 4-Zone controller (approximately 1 foot),

press the center button on the Programmer/Remote to <Exclude>

device in the network.

Factory Default:

If your 4-Zone controller is not responding, or you are unable to control it

after you have tried to Include/Exclude it multiple times, it may be necessary

to reset the 4-Zone controller to its original factory settings. To accomplish

this, proceed as follows:

• On the 4-Zone controller (refer to ﬁgure), press

and hold the left side of buttons 1 and 3. Wait

approximately 5 seconds until the locator LED turns

Amber and then ﬂashes Red. Release the buttons.

The 4-Zone controller is now reset. Once the

controller is reset, it will be necessary to

Re-Include it to a network before it can be used.

CAUTION: SETTING A DEVICE TO A FACTORY

DEFAULT DOES NOT EXCLUDE THAT DEVICE

FROM A NETWORK. THE EXCLUSION PROCEDURE

MUST STILL BE FOLLOWED TO REMOVE THE

DEVICE FROM THE PRIMARY CONTROLLER’S

INFORMATION TABLE. FAILURE TO DO SO MAY

RESULT IN SYSTEM THAT IS SLOW TO RESPOND, OR MAY FAIL TO

RESPOND TO SOME DEVICES.

Excluding 4-Zone Controller from

Z-Wave® Network:

Step 9

After inclusion process, you must associate the devices to the

controllers. Refer to the Primary Programmer/Remote instruction

sheet for complete details.

NOTE: One (1) Z-Wave® device can be associated to multiple controllers

(up to ﬁve (5) controllers maximum).

NOTE: If using a non-Leviton Programmer/Remote, refer to the

Programmer/Remote instruction sheet for associating a device.

Device Association:

Step 10

Programmer/Remote

Cat. No. VRCPG

1 ON

2 ON

3 ON

4 ON

OFF

Button

Center

Button

G) After all devices are included into the network, the controller must

be updated to allow proper network function. To update controller

proceed as follows:

• If using a non-Leviton Programmer/Remote, refer to the

Programmer/Remote instruction sheet for updating controller.

• If using Leviton Z-Wave® Programmer/Remote, Cat. No. VRCPG,

press the Menu button and scroll down to System Setup. Press

the center button to select System Setup Menu. Choose Advance

Settings. Press the center button to select Network. Press the

center button to select Update "cntrl". When prompted, press

desired button on 4-Zone controller.

• Wait until the VRCPG Programmer/Remote conﬁrms completion.

Update is done.

NOTE: If the 4-Zone controller has been successfully Included in the

network and the user tries to Include it again without ﬁrst excluding it

from the network, the controller will retain the ﬁrst node ID it had received

and ignore the second.

Installation Directions

Navigation menu

Versions of this User Manual:

Views

Navigation