Product Detail Manual

134510-Brochure 134510-Brochure 134510-Brochure Batch9 unilog cesco-content

Emerson-D-Control-Station-Flameproof-Brochure-679844 emerson-d-control-station-flameproof-brochure-679844

: Pdf 488462-Attachment 1 488462-Attachment_1 781381 Batch5 unilog

Open the PDF directly: View PDF .
Page Count: 52

GLOBAL PROTECTION

INTRODUCTION PROTECTING YOUR PEOPLE AND YOUR FACILITIES

Manufacturing and processing facilities, and the environments

they inhabit, continually challenge both man and machine.

With the presence of  ammable gases and vapors, these

locations demand electrical products engineered to provide

proper protection from dangers like heat or spark-induced

ignition.  ey must also endure nature’s toughest treatment

through corrosive ocean air on o shore rigs in the North Sea,

extreme heat at re neries in Saudi Arabia and frigid arctic

winds at mining facilities in the Canadian Oil Sands.

For over 100 years Appleton products have been helping to protect facilities, and their workers.

Whether your geography requires ATEX, IEC, NEC, or CEC certi cation, our product range,

regulatory involvement and technical expertise solve the challenges of out tting your facilities.

Our engineers have developed innovative advancements in lighting, electrical control devices

and instrumentation, making Appleton the leader in the production of hazardous location

electrical products.

At Appleton, we take the challenge of protecting hazardous environments seriously.

It is protection throughout your facility and around the globe.

1

INTRODUCTION IEC/ATEX VS. NEC/CEC HAZARDOUS LOCATIONS 4

LIGHTING INTRODUCTION 6

LED LIGHTING 8

FLUORESCENT LIGHTING 10

HID LIGHTING 12

STROBE & BEACON LIGHTING 14

CONTROLS, ENCLOSURES

& PANELBOARDS INTRODUCTION 16

CONTROLS 18

ENCLOSURES 20

STARTERS 22

CIRCUIT BREAKERS 24

PANELBOARDS 26

PLUGS & RECEPTACLES INTRODUCTION 28

PLUGS & RECEPTACLES 30

CABLE GLANDS,

CONNECTORS & FITTINGS INTRODUCTION 32

CABLE GLANDS & CONNECTORS 34

CONDUIT FITTINGS 38

HEAT TRACING SYSTEMS INTRODUCTION 40

HEAT TRACING SYSTEMS 42

POWER QUALITY

SOLUTIONS INTRODUCTION 44

POWER QUALITY SOLUTIONS 43

GLOBAL UNDERSTANDING AND EXPERTISE

Appleton electrical products help protect re nery production in India, ensure pipeline  ow in South Africa, and maintain deep sea drilling

operations in the Gulf of Mexico. Our worldwide presence demands mastery of the International Electrotechnical Commission (IEC), ATEX Directive

and the North American (NEC/CEC) rules and a full product line for every application throughout hazardous locations.

IEC, ATEX and NEC/CEC rules each identify the amount of exposure, destructive force and ignition temperature of the gas, vapor or dust.

However, the separate regulations differ in their nomenclature and sub-category tracking. To assist in out tting and application, the following

pages show the ratings and categories of each regulation body and reference points.

4

IEC STANDARDS and EN

STANDARDS are identical.

IEC STANDARDS have

become the universal

reference across Europe

and are adopted along

with other admissible

standards in much of the

rest of the world. IEC uses

three Zones to classify

hazardous environment

conditions based on the

duration and amount of

combustible exposed. IEC is

continuously reviewed by a

technical board for updates

and revisions.

IEC/ATEX

INTERNATIONAL ELECTROTECHNICAL COMMISSION (IEC)

Founded in 1904, the IEC is now considered the world’s largest electrotechnology organization with over 130

countries as members and over 10,000 experts contributing to its standards.  e IEC code de nes hazardous

locations as Zones. Zones de ne the amount of time rated equipment is exposed to hazardous atmospheres.

Zone 0 locations feature continuous or extended exposure to  ammable gases or vapors. Zone 1 locations have an

intermittent presence of  ammable gases or vapors, typically as a result of leakage. Zone 2 are locations in which

 ammable gases or vapors are not likely to occur in normal operation, but may become present upon the failure

of equipment or through an accident.  e exposure is unlikely and, if it does occur, it will do so infrequently and

for only a short period of time. Atmospheres of combustible dusts are rated as Zone 20, 21 or 22. Zones 20, 21

and 22 correspond with Zones 0, 1 and 2 in identifying the amount of exposure to the hazardous atmosphere.

IEC Groupings rate locations on whether the hazard is a mine (Group I) or an ignitable atmosphere above ground

(Group II). IEC Subdivisions label the ignitability of the atmosphere with “A” being the least ignitable and “C”

being the most.

ATEX DIRECTIVE

 e ATEX Directive is the  rst uniformed code which deals with the Essential Health and Safety Requirements

(EHSR’s) enacted by the European Union for equipment that is either used within, or connected to equipment

located within, potentially hazardous environments. It includes safety devices, controllers, regulatory devices and

other equipment whose failure would provoke an explosion.

Area Classification - IEC vs NEC/CEC (Class/Division/Group) IEC vs NEC “T” Ratings Temperature Classification Comparison 

In ammable Material IEC/CENELEC NEC/CEC Temperatures in ºC IEC NEC/CEC

Gases And Vapors Zone Equipment Group Gas Group Class Division Group

Acetylene 0, 1 or 2 II C I 1 or 2 A 85 T6 T6

Hydrogen 0, 1 or 2 II B + H2I 1 or 2 B 100 T5 T5

Propylene Oxide

0, 1 or 2 II B I 1 or 2 B

120 T4 T4A

Ethyl Oxide 135 T4 T4

Butadiene 160 T3 T3C

Cyclopropane

0, 1 or 2 II B I 1 or 2 C

165 T3 T3B

Ethyl Ether 180 T3 T3A

Ethylene 200 T3 T3

Acetone

0, 1 or 2 II A I 1 or 2 D

215 T2 T2D

Benzene 230 T2 T2C

Butane 260 T2 T2B

Propane 280 T2 T2A

Hexane 300 T2 T2

Paint Solvents 450 T1 T1

Natural Gas

 “T” rating classifications list the ignition point of the hazardous atmosphere. For safe usage, fixture “T” ratings must be below that of the surrounding atmosphere.

5

NEC/CEC STANDARDS

operate across the U.S.,

Canada, the Middle East

and various locations across

the globe. NEC code is

reviewed and updated in

three year cycles.  e CEC

code is updated regularly

through their 9,000

members and its active

involvement with the IEC.

NEC/CEC

NATIONAL ELECTRICAL CODE/CANADIAN ELECTRICAL CODE (NEC/CEC)

 e NEC has been the standard for electrical wiring and equipment installations in the United States since 1897.

 e CEC began in 1927 and provides the electrical product standards for Canada. NEC/CEC Code categorizes

hazardous locations into Classes, Divisions and Groups. Classes I, II and III de ne hazards into gases and vapors,

combustible dusts, and  bers and  yings, respectively. Divisions further break down the Classes by the amount of

the exposure to the combustible. Division 1 establishes locations where hazards are present during regular operations.

Division 2 locations are where hazards are encountered only during an abnormal situation, such as equipment

failure or a spill. Gas groups classify the explosive nature of the gas, vapor or dust when ignited.

US (NEC 500) and CA (CEC Annex J) EU (Directive 94/9/EC) - ATEX

Explosionproof with I.S. Outputs, Class I,

Division 1, Groups A, B, C, D, T5

Type of Protection

(optional except for I.S.)

Temperature Class

(T5 and T6 optional)

Permitted Division

(optional except for Division 2)

Permitted Gas Group

Permitted Class

Product Marking Charts 

US (NEC 505)

Class I, Zone 1, AEx d [ia] IIC T5

Permitted Class

Permitted Zone

American

National Standard

Explosion-Protected

Type of

Protection

I.S. Output

Group

Gas Group

Temperature Class

IEC and CA (CEC Section 18)

Ex d [ia] IIC T5

Explosion-Protected

I.S. Output

Type of Protection

Group

Gas Group

Temperature

Class

Ex d [ia] IIC T5

European

Standard

Type of Protection

I.S. Output

Group

Gas Group

Temperature Class

Explosion-Protected

0081 II 2 G

CE Conformity Marking

Identifi cation Number of Notifi ed Body

Involved in Protection Control Stage

Explosion-Protection

Marking

Equipment Group:

I (for mines)

II (for other than mines)

Category:

1 (for Zone 0 or 20)

2 (for Zone 1 or 21)

3 (for Zone 2 or 22)

Type of Explosive Atmosphere:

G (for gas, vapor and mist)

D (for dust)





Certifications and performance

markings are displayed on all

electrical equipment to ensure

proper conformity to each

hazardous location’s requirements.

Appleton offers products approved

for ATEX, IEC, NEC and CEC

locations.

 Ambient temperature ranges other than standard -20 °C ≤ Ta ≤ +40 °C (-4 °F ≤ Ta ≤ +104 °F ) must be marked.

6

LIGHTING WHENEVER AND WHEREVER YOU NEED US

From the loading bays to the re ning rooms, facilities across the world

rely on lighting  xtures to safely illuminate the narrow catwalks,

enclosed production  oors and 24 hour docks that connect its four

corners. Besides providing light, these critical  xtures must overcome

the inherent challenges and threats of hazardous environments.

7

Appleton’s line of enclosed and gasketed  xtures are the perfect choice for use in Division

and Zone locations. Our vented re ectors result in cooler operation and increased lumen

output. Appleton’s restricted breathing  xtures are secure from water, gases and vapors.

Our  xtures are corrosion-resistant with stainless steel hardware and epoxy powder coated

copperfree aluminum. Even a feature like our “safety” high hinge provides additional

protection against accidental ballast housing disengagement while your maintenance team

is installing or servicing them.

Our line of  ameproof and explosionproof  xtures are available for use in Division and

Zone 1 and 2 locations. With intelligent engineering, they are manufactured to prevent

internal explosions from reaching the vapors surrounding the  xture by cooling the hot

gases through precise  amepaths. Appleton’s explosionproof  xtures also address safety

outside of the lamp with innovative features like proprietary wireless mounting hoods that

allow for quicker and safer “hot” installation or servicing.

From our  uorescent  xtures to our high durability high pressure sodium luminaires

with long lamp life and low “T” ratings, Appleton’s entire line of lighting products deliver

unparalleled protection across your facility. Our proprietary coatings keep corrosion at

bay while our exclusive re ector technology and class leading photometrics deliver the

maximum amount of light possible. Appleton also boasts more  xtures for use in high

ambient applications and the lowest “T” ratings in the industry for improved performance

and wider applications.

We relentlessly test our  xtures to ensure they meet or exceed their rated capabilities even

in the most extreme conditions.  at is why facility engineers around the world have

turned to Appleton for lighting products that improve e ciencies while protecting

their workers.

8

LIGHTING

ATEX/IECEx/NEC/CEC

LED LIGHTING MERCMASTER™ LED SERIES

LED lighting has come to hazardous locations, and Appleton’s Mercmaster LED is setting the

industry standard for safety, performance and e ciency. In day-to-day use, installation and

maintenance, the Mercmaster LED’s superior design simply shines. It is not just about e ciency.

LED lighting delivers real productivity bene ts.

• Compact lightweight low pro le design, well suited for low mounting heights

• Multiple mounting hoods accommodate any application requirement

• Fixture housing and mounting hoods are copperfree cast aluminum for better heat dissipation.

All exposed hardware is stainless steel

• Rounded edges throughout the heatsink reduce risk of injury during installation and

maintenance

• Hinge design increases safety during installation and servicing, assuring 360° compression on

ballast housing gasket

• Silicone rubber gasket seals out moisture, dirt and dust; stays  exible and withstands high

temperatures

• Polycarbonate lens is threaded for easy removal and secure attachment

• Epoxy powder coat  nish and stainless steel latch assembly are corrosion resistant

• Dark Sky Compliant: meets speci cations for low glare, focused beam and avoidance of

overlighting

ATEX/IECEx/NEC/CEC

LED LIGHTING AREAMASTER™ LED SERIES

Appleton’s Areamaster LED is versatile with a universal design for  ood or high bay mounting,

making it ideal for replacing virtually any HID,  uorescent or incandescent  xture. Rated at 127

Watts, it delivers an optimal 13,000+ lumens of cool white light. Moreover, its highly directional

light does not require the use of external optics, resulting in system e ciencies as high as 80

percent.

• Compact in size, attractively styled contemporary design, rugged and dependable

• Easy to install and service

• One piece housing

• One piece lens hinged cover. Secured by four M6 captive stainless steel slotted hex head bolts

•  ermal shock and impact resistant glass lens

• Heavy duty, high temperature, single piece, formed silicone rubber gasket

• Universal design for  ood and high bay mounting; vibration rated in all con gurations

• Dark Sky Compliant: meets speci cations for low glare, focused beam and avoidance of

overlighting

9

LIGHTING

ATEX/IECEx

LED LIGHTING FDBAES SERIES

Appleton’s ATX FDBAES Series LED provides emergency lighting in hazardous locations.  ese

units are entirely self-contained in a  ameproof enclosure, and include a built in automatic self-

test system. Switched, unswitched, addressable switched and addressable unswitched versions are

available

• Provides adequate lighting and/or visual indication of access on exit routes during an

evacuation in a hazardous environment

• Can be installed in hazardous areas designated as Zone 1-2 and 21-22

• Padlockable switch is available on switched models which individually cuts o power supply

and remote control

• All versions:

– Can be maintained in hazardous areas as an internal switch cuts o battery supply

automatically once the cover is unscrewed and opened

– Charge indicator with 4 nos yellow LEDs (lifetime over 10 years)

– Operates in any position

– Automatic built-in self-test system (SATI) with memorization of tests indicated by LEDs

ATEX/IECEx

LED LIGHTING FNES SERIES

Appleton’s ATX FNES Series LED provides emergency lighting in hazardous locations and can also

be equipped with a variety of labels to indicate exit routes.  ese units are entirely self-contained,

and include a built in automatic self-test system.

• Provides adequate lighting and/or visual indication of access and exit routes during an

evacuation in a hazardous environment

• Can be installed in hazardous areas designated as Zone 2 and 21-22

• Non-maintained

• Operates in any position

• Charge indicator by green LED (lifetime over 10 years)

• Automatic built in self-test system (SATI) with memorization of tests indicated by LEDs

• Using a microprocessor and an internal clock, the unit will carry out automatic tests

• Remote control unit allows the  xture to be controlled and checked without switching the

mains o

•  e remote control unit installed in a safe area or inside a  ameproof box allows manual

ignition of all the units (maximum 300 units) for visual inspection of their operation

10

LIGHTING

ATEX/IECEx

FLUORESCENT LIGHTING FE™ SERIES

Appleton’s ATX increased safety FE Series of  uorescent  xtures go a step beyond with added

protection for everyday locations, as well as robust environments where corrosive atmospheres,

severe weather and detergents prevail.  ese  uorescent  xtures are protected against the elements

with an elastomer gasket that ensures a consistent, durable seal that is hosedown ready.  e

corrosion-resistant lens, body and hardware mean the FE Series  uorescent luminaires will endure

the years.  ese  xtures o er a host of exclusive safety features that make servicing safe and easy.

• Hinged polycarbonate di user and multi-parabolic re ector for one handed maintenance

• Quick connector ballasts and IP 2X terminal shields

• Opening re ector activates power cut o switch to unit for safe access to internal controls

• If one tube fails, the other tubes remain lit

• Elastomer gasket and multiple cover fasteners

• Pre-impregnated  berglass reinforced polyester body

• Optional dimmable switch alternates which tubes are lit for di erent lighting patterns and

brightness

NEC/CEC

FLUORESCENT LIGHTING FV™ SERIES

 e FV Series places cost e ective  uorescent lighting in Class I, Division 2 marine and other

robust locations. O ering unprecedented safety and durability, the FV Series lens is rugged enough

to endure hose downs and o ers single handed lamp and internal control access.  e internal

re ector is hinged for easy access to the control gear.  e lens automatically engages a unit cut o

switch when opened.  e FV Series stays cool with a T6 rating while operating with a remarkable

94% light producing e ciency.

• Nearly indestructible polycarbonate lens cover

• Automatic unit cut o switch

• Corrosion-resistant  berglass reinforced polyester housing

• Single actuator enables one handed lens and re ector access

• Actuator can be removed for tamper-proof operation

• Multiple latch design and elastomer gasket provide a positive watertight seal

11

LIGHTING

NEC/CEC

FLUORESCENT LIGHTING MERCMASTER™ III LOW PROFILE

 e Mercmaster III Low Pro le enclosed and gasketed  xture o ers superior lighting

in a small package for Class I, Division 2/Zone 2 locations. It is the perfect choice for low

clearance, low ceiling heights or where  xture weights must be minimized.  e PLT  uorescent

lamps provide superior lighting e ciencies and economies. Its electronic ballast allows for  icker

free, instant-on capabilities for zero blackout during momentary power dips.  e Mercmaster

III Low Pro le is also suited for non-hazardous areas that are exposed to severe weather, excessive

moisture, dirt and dust.

• Maintains high output lighting in ambient temperatures ranging from -5°C to +54°C

(+23°F to +130°F)

• Excellent color rendering (82 CRI) for food processing and inspection facilities

• Compact pro le is perfect for low clearance locations

• Baked epoxy powder coat  nish and stainless steel hardware for the ultimate corrosion

resistance

• Captive clamping bolt and high safety hinge provide for safe, easy maintenance

• Stainless steel threaded inserts prevent galling and freezing of re ectors, guards and other

bolt-on attachments

NEC/CEC

FLUORESCENT LIGHTING EFU FLUORESCENT SERIES

 ese factory sealed, explosionproof and dust-ignitionproof  uorescent light  xtures are suited

for any location where ignitable dust, fumes, gases, paint residue, paint powder or corrosive

atmospheres are present, including inside a paint spray booth.  e EFU’s Class P ballasts feature

a thermally-activated protective device that guards against excessive voltage, internal ballast short

circuiting, inadequate lamp maintenance and improper  xture applications.

• Non-sparking exterior surfaces for safer operation

• Instant Start and Rapid Start options

• Available cold weather ballasts for -18°C (0°F) starting

• Heat and impact resistant glass tubes

• Re ectors are easily removed for replacement or cleaning

• Explosionproof caps can easily be removed for quick wiring and relamping

12

LIGHTING

ATEX/IECEx/NEC/CEC

HID LIGHTING AREAMASTER™

Appleton’s rugged, enclosed and gasketed, Areamaster  oodlights are rated for Class I, Division 2/

Zone 2 and severe non-hazardous environments. Areamasters resist corrosion with a one piece,

pressure cast, copperfree aluminum housing that features an architectural bronze polyester  nish.

Its compound parabolic and double segment design, with an Alzak  nished aluminum re ector,

provides optimum light distribution and e ciency.

• Compact size  ts more locations

• Guard and re ector attached externally for quick and safe maintenance

•  ermal shock and impact resistant glass

• Plug-in terminal block

• Available for use in conditions de ned as Class I, Zone 2 AEx nR IIC utilizing restricted

breathing as the method of protection

ATEX/IECEx

HID LIGHTING HBDC SERIES CYLINDRICAL BULKHEAD LIGHTS

Realize cost e ciencies and safety in Zone 1-2 and 21-22 locations with  ameproof bulkhead

 xtures. Appleton’s ATX HBDC Series produces industry leading photometrics for more light

in critical locations and feature high temperature internal wiring for extended durability.  eir

housing design allows them to be mounted out of the way for safe lighting without added

obstacles.

• Hardened lamp glass

• Available with integrated lug mounts

• Corrosion-resistant housings, end caps and cover

• Guard and re ector attached externally for quick and safe maintenance

•  readed access cover with O-ring seal

• Plug-in terminal block

ATEX/IECEx

HID LIGHTING PB SERIES FLOODLIGHTS

Keep large areas well lit and safe with Appleton’s ATX series of explosionproof and enclosed and

gasketed  oodlight products. Our optional mounting, e cient light patterns and various wattages

enable you to put the light you need, wherever you need it. Floodlights are available for locations

as cold as -40°C (-40°F) and as high as +55°C (+131°F). We also use a ferromagnetic ballast for

optimal energy e ciency, reduced power loss, higher light output and increased lamp service life.

• Hinged mounts and pivoting lenses for easier mounting and repair

• Internal controls are insulated by Class H materials for maximum service life

• Corrosion-resistant, lightweight aluminum alloy housings conform to AFNOR

French codi cation

• Self tightening connection terminal blocks

• Operates at any angle

• Safety terminal box allows for safe and straightforward installation

• Adjustable beam angles

13

LIGHTING

IEC

HID LIGHTING AND

COMPACT FLUORESCENT NE850 SERIES

Appleton’s Nutsteel  ameproof NE850 Series of wellglass  xtures are rated Ex d, IIC for Zone 1

and 21 locations. Compact, e cient and lightweight, they o er an IP 66 and can be installed in

any harsh environment.  eir size makes them perfect for low clearance locations or where  xture

weight needs to be considered. Operating temperatures range from -20°C to +55°C (-4°F to

+131°F). An emergency version with battery back up is available.

• Shock resistant globe

• Corrosion-resistant fastenings

• REVESTEEL® anticorrosive coated aluminum body and guard

• AISI 304 stainless steel screws and lock washers

• Numerous lamping and mounting options

• 220 V, 60 Hz, 230/240 V, 50 Hz

NEC/CEC

HID LIGHTING MERCMASTER™ III

 e Mercmaster III’s modular construction allows it to  t a vast range of applications and is

suitable for Class I, Division 2/Zone 2; Class II, Division 1 and 2; Class II and other robust

environments. Designed to dissipate heat from the ballast components out, Appleton’s thermal

performance with the Mercmaster III leads the industry. Appleton’s heat reducing internal

control design results in 18% cooler operation, which increases  xture durability and enables the

Mercmaster III to be used in ambient temperatures up to +65°C (+149°F).

• Choice of heat-resistant prismatic glass refractors or globes

• Housing, hoods and guards are copperfree cast aluminum with baked epoxy powder coat  nish

for superior corrosion-resistance

• “Safety” high hinge and swing away design eases servicing

• Capacitors are non-PCB type and thermally isolated from the ballast

• Mogul base porcelain socket features nickel plated contacts and +200°C (+392°F) welded leads

for trouble free operation in high ambient temperature locations

NEC/CEC

HID LIGHTING CODE•MASTER™ 2

 e explosionproof Code•Master 2  xture features Appleton’s proprietary technology for

maximum safety and reliability in Class I and II locations. Internal components

are uniquely arranged for the greatest heat dissipation, which enables extended lamp life and

industry leading “T” ratings. Appleton’s exclusive wireless mounting hood enables power on  xture

installation and removal in hazardous locations.

• Double lead Acme threading allows for  ame-tight seals with fewer turns

• Lamp socket and glass globe designed for optimum light distribution and control

• Factory sealed — no external seals are required

• Fixture and mounting hood threads are pretreated with no gall, anti-seize coating

• Porcelain socket and nickel plated phosphor bronze screw shell assures long, trouble free

operation in high ambient areas

• Wide variety of mountings and light sources

14

LIGHTING

ATEX/IECEx

STROBE & BEACON IIC BEACONS & STATUS LAMPS

Appleton’s ATX series of  ameproof lighting  xtures o ers visual communication

in Zone 1-2 and 21-22 locations. Illuminated three stage indicator banks consist

of interchangeable colored modules that can be coupled with two other modules

for simultaneous lighting. Beacons are o ered up to 15 joules, which maintain a

remarkable 70% luminosity after eight million  ashes. Various mountings, colors

and guards are available.

• High temperature internal wiring

• Polymethacrylate globes are available in red, green, orange and clear

• Corrosion-resistant exteriors

• Operating temperatures range from -40°C to +55°C (-40°F to +131°F)

• Mounting hardware available in either stainless steel or zinc plated steel

• All beacons and status lamps work in any position

15

LIGHTING

NEC/CEC

STROBE STYLMASTER™

 e enclosed and gasketed Stylmaster strobe is suitable for Class I, Division 2/Zone

2 and Class II, Division 1 and 2 locations.  e Stylmaster uses more than two  ashes

and light rotations per second to alert facility personnel of unsafe conditions or other

communications that require visual cues.

• Factory installed lenses available in red, amber, blue, green and clear

• Heat and impact resistant globes have smooth, dust resistant exterior

• Minimum operating temperature of -25°C (-13°F)

• Suitable for base up and base down applications

NEC/CEC

STROBE CODE•MASTER™

Appleton delivers strobe technology in an explosionproof  xture for Class I and

Class II locations.  e Code•Master strobe utilizes Appleton’s proprietary wireless

mounting hood attachment for safer maintenance and installation. Fixtures can be

unscrewed hot from the mounting hood in hazardous locations.

• Acme double lead, no gall threads speed  xture installation and removal

• Factory sealed — no external seals are required

• Operates in high ambient temperature environments

• Suitable for base up and base down applications

16

CONTROLS, ENCLOSURES

& PANELBOARDS PLACING POWER SAFELY IN YOUR CONTROL

Powering equipment throughout a Division 2, Zone 2 facility requires

highly engineered controls, enclosures and panelboards. Appleton’s

extensive product o erings are manufactured to exceed the demands

of facilities all over the globe, including severe weather and chemical

environments.  ey are engineered and designed to keep your

machinery and the workers using them safe, now and for years into

the future.

17

Appleton designs, builds and tests their electrical control products to maximize both

passive and active safety operation. Passive safety means that your equipment will

perform, even under profound stress. Passive safety engineering prevents potential sparks

from causing an explosion, provides durable housings that keep corrosion at bay and

incorporates devices that function reliably for decades.

We incorporate active safety design into our controls, enclosures and panelboards, as well.

Active safety engineering is about designing products that blend into your environment,

are user friendly and work reliably. Smooth and accurate switches, high visibility pilot

lights and customizable control interfaces all decrease the possibility of user error while

increasing production e ciencies.

18

CONTROLS, ENCLOSURES & PANELBOARDS

ATEX/IECEx/NEC/CEC

CONTROLS UNICODE 2

 e Unicode 2 control station is tri-rated for ATEX, IEC and NEC/CEC compliance allowing

for use in virtually every industrial application worldwide.  ese factory sealed control stations

are rated for Zone 1-2 and Class I, Division 2 locations. Available materials include  berglass

reinforced polyester (FRP), polyamide, 316L stainless steel and cast aluminum with a polyester

powder coat.  e Unicode 2 o ers a wide selection of conduit or cable gland entries on both the

top and bottom of the box.

• Gasketed for IP 66, NEMA 3, 3R, 4 and 4X ratings

• T35 rail mounted components are held securely in place during operation and can be easily

removed for servicing or modi cations

• Captive corrosion-resistant stainless steel cover screws

ATEX/IEC/NEC/CEC

CONTROLS ACSEW CAST CONTROL PANEL

Combine controls, indicators and meters into one explosionproof control center.  e ACSEW

is  exible enough to be used in an array of applications with a variety of button, switch and pilot

device combinations, including di erent sizes of meter windows. Gray epoxy powder coat is

available to provide a NEMA 4X rating.  e internal cavity is kept spacious by an external  ange

and accepts operators spaced on 2½” centers.

• Factory assembled and wired to specs

• Sand cast copperfree aluminum

• Wall thickness handles a minimum of seven full threads

• All push buttons and selector switches have stainless steel shafts

ATEX/IECEx

CONTROLS INCREASED SAFETY CONTROL PANEL

Appleton’s ATX series of polyester or 316L stainless steel control panels are available with multiple

operator functions including push buttons, selector switches, pilot lights and ammeters.  is series

comes in a wide variety of sizes and con gurations and is o ered with removable gland plates.

• Panels can be  tted with horizontal or vertical DIN rails

• Operating temperatures range from -30°C to +55°C (-22°F to +131°F)

• Supplied with identi cation labels

ATEX/IEC

CONTROLS EX d FLAMEPROOF CONTROL STATIONS

Appleton’s ATX series of  ameproof control stations bring modular design into Zone 1-2 locations.

 ese control stations come in a variety of sizes and hole patterns for di erent jobs. Controls are

available separately for on site assembly of control stations while retaining the  ameproof integrity.

•  readed  ameproof joints

• Gray painted, marine grade, aluminum alloy or cast iron boxes

• Available with push buttons, pilot lights and selector switches

19

CONTROLS, ENCLOSURES & PANELBOARDS

IEC

CONTROLS NECCS CONTROL STATION

Appleton’s Nutsteel NECCS Series of copperfree aluminum control stations come assembled

according to design speci cations.  ey are rated for Zone 1-2, Ex d IIB locations.  is series

is available with pushbuttons, pilot lights, selector switches, emergency stop buttons and can

accommodate up to 25 components.

• Supplied with stainless steel hardware

• Supplied with internal mounting plate

• IP 65

• Temperature Class of T5 or T6

• Revesteel® anticorrosive coated aluminum body and cover

NEC/CEC

CONTROLS EFDB/EFD/EDS SERIES

Factory sealed EFDB/EFD/EDS Series of control stations are ready for heavy duty applications

with a 10 A/600 V rating and dozens of combinations of buttons, pilot lights and selector switches.

 is series is con gurable to match the demands of almost any environment. Enclosed stainless

steel helper springs prevent accidental operation of the push button in severe vibration situations.

 ese control stations include stainless steel push button shafts that operate within stainless steel

bushings for long lasting, maintenance free usage.

• Malleable iron or aluminum bodies with aluminum covers o er high thermal and arc resistance

along with high dielectric strength

• Optional two or three position selector switches with modi ed operation

• Front operated push buttons are supplied with standard lockout type guards

NEC/CEC

CONTROLS INTRAGROUND NONMETALLIC CONTROL STATION SERIES

Appleton’s pioneering Intraground Series were the  rst nonmetallic control stations UL Listed for

Class I, Division 1 locations.  e thermoplastic polyetherimide box and cover can support 33,000

psi  exural strength and retain perfect integrity after  ve UL gas burner tests.  e cover and box

also retain their integrity after being submerged in water for 336 hours and exposed to 720 hours

of ultraviolet radiation.

• Nonmetallic construction with embedded grounding grid

• Superior conduit connection strength – UL pull out and bending resistance tests have proven

no e ect on conduit connections

• UL temperature index ratings as high as +170°C (+338°F)

20

CONTROLS, ENCLOSURES & PANELBOARDS

ATEX/IECEx/NEC/CEC

ENCLOSURES FIBERGLASS REINFORCED POLYESTER TERMINAL ENCLOSURES

Appleton’s ATX JBEP Series of increased safety enclosures are o ered with an IP 66 rating and are

available in multiple sizes depending on the number of terminals installed.  eir modular design

allows for similar sized terminal enclosures to be coupled together for ease of wiring during  eld

installation. Terminal enclosures are ATEX approved for use in Zone 1-2 and 21-22 locations.

• Removable gland plates available

• Cable glands installed per customer requirements

• Carbon impregnated enclosure for static resistance

ATEX/IECEx/NEC/CEC

ENCLOSURES 316L STAINLESS STEEL TERMINAL ENCLOSURES

For corrosion-resistance, a clean appearance and  exible application options, Appleton’s ATX series

of stainless steel increased safety boxes and enclosures are the answer. Boxes are available in a variety

of sizes with depths ranging from 95 mm to 300 mm (4 in to 12 in).  e boxes come ready to be

drilled on site or come pre-drilled from the factory. Doors are reversible and open either up and

down or to the left and right. Each box features reversible anti-vibration mounting brackets.

• Vertical and horizontal mounting options

• Available with up to 204 cable entries per box face

• Optional removable padlock device

• Can be custom made to your speci cations. Contact our Technical Support group

ATEX/IEC/NEC/CEC

ENCLOSURES INCREASED SAFETY JUNCTION BOXES

Junction boxes are available in a wide range of con gurations for increased safety applications.

Boxes for non-armored and armored cable come in high impact resistant polycarbonate bodies and

covers. Appleton’s ATX series of junction boxes feature two kinds of terminals: a spur multicore

pillar terminal and junction isolated terminals that can be clipped onto a DIN rail.

• Body and cover available in four materials

• Available with identi cation labels

• Corrosion-resistant

ATEX/IEC/NEC/CEC

ENCLOSURES AJBEW SERIES

 e AJBEW Series junction box can be used to house control stations, starters, breakers, relays and

meters. It can also be used for splicing wire terminals or as a pull box, bus box or custom panel in

Class I and II locations.  e AJBEW is made from cast copperfree aluminum and can be mounted

vertically or horizontally with a wide range of drilled and tapped outlet options.

• Hinges are standard on 300 mm to 300 mm (12” x 12”) and larger sizes

• Optional gray epoxy powder coat provides NEMA 4X rating

• Custom drilling and tapping

21

CONTROLS, ENCLOSURES & PANELBOARDS

ATEX/IEC

ENCLOSURES FLAMEPROOF CAST JUNCTION BOXES

Appleton’s ATX series of  ameproof junction boxes can be custom drilled to  t your speci c

application by our precision machining services. Cable entries can be distributed over all four

sides. Wide interior space o ers substantial room to work.  e IIB  ameproof boxes come in gray

painted cast iron or steel, marine grade aluminum alloy and stainless steel.

• Inner compression locking nut retains inner seal during inspection of earth continuity

• Available bus bar systems

• Just one clamping ring allows foolproof assembly

NEC/CEC

ENCLOSURES GUBB SERIES

Ideal for indoor and outdoor use, the GUBB Series of junction boxes are designed for Class I and

II locations containing such gases as butane, gasoline, hexane, naphtha, benzene, lacquer solvent

vapors and alcohol. An optional mounting plate can be drilled to accommodate a variety of

devices. Dome covers are available for added interior capacity.

• All conduit openings and hubs provide for a minimum of  ve full threads to meet

UL requirements

• Wide selection of sizes and con gurations to enclose relays, instruments and other controls

• Manufactured with either high tensile strength malleable iron or copperfree aluminum

• Iron bodies are triple coated with zinc electroplate, chromate and epoxy powder coat

• Aluminum bodies and covers feature an epoxy powder coat

• Available with window in cover

NEC/CEC

ENCLOSURES AGUB

 ese instrument and meter enclosures are explosionproof and dust-ignitionproof.  ey protect

electrical devices and provide wire pulling locations in hazardous atmospheres. Large cover

openings allow for easy access to wires and can be  tted with window covers for the safe display of

gauges or indicators.

• Copperfree aluminum housings

• Standard corrosion-resistant, gray epoxy powder coat

• Cast mounting feet

NEC/CEC

ENCLOSURES GR BOXES

 ese explosionproof conduit outlet boxes are o ered in 10 hub arrangements and meet a wide

range of rated area requirements. Furnished with an internal ground screw and mounting hubs for

terminal strip, the GR Series is manufactured from either malleable iron for high tensile strength

and ductility or aluminum for lighter weight. Both box materials feature high corrosion-resistance

and accurately tapped, tapered hub threads for secure joints and ground continuity.

• Standard O-rings provide a raintight  t for NEMA 3, 4 ratings

• Smooth, rounded integral bushing protects conductor insulation

• Function as sealing  ttings when used with sealing covers

22

CONTROLS, ENCLOSURES & PANELBOARDS

ATEX/IEC

STARTERS MOTOR STARTERS

Appleton’s ATX series of Ex d  ameproof motor starters and contactors are compact but rugged

for long lasting use in hazardous environments.  ese motor starters are available in three electrical

con gurations: DOL (Direct on Line), YD Star-delta and reversing with breaking capacity from

.37 to 75 KW up to 690 volts.  e IP 66 rated enclosure comes in a variety of sizes dependent

upon the size of starter and the option chosen. Ex d  ameproof motor starters are approved for use

in Zone 1-2 and 21-22 locations.

• Marine IP 66 rated cast aluminum with powder polyester  nish comes in three sizes depending

upon start/contactor size

• Available from .37 to 75 KW up to 690 volts

• Motor starters can be con gured for various controls, such as pushbuttons, selector switches

and pilot lights

• All exterior hardware is 316 stainless steel

• Supplied complete with protection breaker

• Various cable entry sizes can be drilled and tapped

IEC

STARTERS NEPPS AND NEPPM MOTOR STARTERS

Appleton’s Nutsteel NEPPS and NEPPM Series are designed for use in Ex d IIB, Zone 1-2

locations.  e NEPPS Series are designed for DOL (Direct on Line), starters for motors up to

0.75 HP at 220 V (1-phase), 1 HP at 220 V (3-phase) and 2 HP at 380 V (3-phase).  e NEPPM

Series is designed for DOL starters up to 60 HP at 220 V, 100 HP at 380 V or 125 HP at 440 V.

• Fully assembled with the following components:

- Contactor

- Circuit breaker

- Time delay relay, adjustment 6-60 seconds

- “On” - “O ” button

- Indicator light

- Overload relay

- External grounding terminal

•  e time relay assures automatic shutdown in 60 seconds, if the operator does not press the

reset button

• Revesteel® anticorrosive coated copperfree aluminum body and cover

• Cover  xed with captive screws. All hardware is made of AISI 304 stainless steel

23

CONTROLS, ENCLOSURES & PANELBOARDS

NEC/CEC

STARTERS AEB SERIES

Suited for hazardous and wet environments, the AEB Series delivers Appleton’s explosionproof,

dust-ignitionproof and watertight engineering capabilities into bolted, full voltage motor starter

con gurations.  ese starters o er the most robust power handling features and capacity available

for combination and non-combination needs.  e AEB is formed from copperfree aluminum with

stainless steel hardware and mounts components on a galvanized steel removable pan.

• 65,000 AIC. Highest interrupt rated enclosure in the industry

• Precision machined  ame path between box and cover

• Four point control terminal block, NEMA 1B with wire markers

• Corrosion-resistant gray epoxy powder coat inside and out

• Breaker handles on combination starters can be locked in the “On” or “O ” position

• Stainless steel hinges and cover bolts

• Designed to accept Cutler-Hammer, GE or Square D starters (consult local sales representative

for other options)

NEC/CEC

STARTERS AE THREADED SERIES

Appleton’s AE Series of starters can be designed to  t any application in your facility.  e AE Series

delivers Appleton’s explosionproof and dust-ignitionproof protection with a watertight sealing

into bolted, full voltage motor starter con gurations.  ese starters o er the most robust power

handling features and capacity available for combination and non-combination con guration

needs.  e AE is formed from copperfree aluminum with stainless steel hardware and mounts

components on a galvanized steel removable pan.  e AE Series are threaded type, full voltage

starters that provide the ability to manually disconnect power while o ering under voltage, circuit

and motor running protection.  e copperfree aluminum housing is NEMA 4X rated and features

internal Acme screw type threads that protect against damage, galling and contaminants. AE

enclosures  t Cutler-Hammer, GE or Square D starters.

• Enclosures furnished with or without components

• Drilled and tapped outlets available in various sizes

• Breaker handles on combination starters can be locked in the “On” or “O ” position

(combination starters only)

• Reset operator features stainless steel shaft

• Outlets provided for remote control wiring

• Circuit breaker mounted outside the center housing for easy accessibility

• Spacious housing for installation and wiring of additional accessories

• 65,000 AIC. Highest interrupt rated enclosure in the industry

• Precision machined  ame path between box and cover

• Four point control terminal block, NEMA 1B with wire markers

• Corrosion-resistant gray epoxy powder coat inside and out

24

CONTROLS, ENCLOSURES & PANELBOARDS

ATEX/IEC

CIRCUIT BREAKERS FLAMEPROOF CIRCUIT BREAKERS

Appleton’s ATX series of Ex d  ameproof load and motor circuit breakers provide short circuit

protection and control of your electrical equipment and motors.  ese three-phase breakers are

rated up to 690 volt and up to 125 Amp.  e IP 66 marine grade enclosure is rated for rugged

and hazardous environments.  ese breakers also serve as a disconnect means for lighting, heating,

motors and other equipment.  ey are ATEX approved for use in Zone 1-2 and 21-22 locations.

• Marine IP 66 rated cast aluminum enclosure with powder polyester  nish comes in various

dimensions depending upon breaker size

• Available from 25 to 125 Amp up to 690 volts

• Fast electromagnetic trip, adjustable thermal overload and phase failure sensitive

• Can be con gured for various controls such as pushbuttons, selector switches and pilot lights

• All exterior hardware is 316 stainless steel

• Various cable entry sizes drilled and tapped

• Easy access with gasketed hinged door cover

IEC

CIRCUIT BREAKERS NEDJ CIRCUIT BREAKERS

Appleton’s Nutsteel NEDJ Series of Ex d circuit breakers are available with an optional GFI.  e

1-pole, 2-pole and 3-pole thermomagnetic circuit breaker meets IEC 60947-2 standard. It is

suitable for control and protection of electrical circuits against overloads and short circuits in Zone

1-2, Ex d IIB locations.

• Circuit breakers are installed on DIN rails, on a steel electroplated mounting plate

• Circuit breakers available from 1 Amp up to 63 Amps

• Terminals for connecting 25 mm2 (0.0387 in2) cables for circuit breakers up to 25 Amp; and

35 mm2 (0.0542 in2) cables for circuit breakers from 35 Amp to 63 Amp

• Revesteel® anticorrosive coated copperfree aluminum body and cover

• Cover  xed with captive screws. All hardware is made of AISI 304 stainless steel

25

CONTROLS, ENCLOSURES & PANELBOARDS

NEC/CEC

CIRCUIT BREAKERS AE SERIES

 e AE Series of circuit breaker enclosures are explosionproof, dust-ignitionproof and watertight.

Precisely engineered  amepaths are machined between the box and the cover. Sand cast from

copperfree aluminum, the box has been designed for maximum interior space and features stainless

steel mounts, hardware and handle.

• Breaker handle can be locked in “On” or “O ” position

• Plugged outlets on top and bottom for breather and drain

• Easy mounting

• Wide range of drilled and tapped outlets

• Corrosion-resistant, non-sparking copperfree aluminum with two coats of epoxy powder

coat  nish

• Interior components are removable as an assembly to make wire pulling easier

• Designed to accept Cutler-Hammer, GE or Square D breakers

• Stainless steel captive Quad-Lead® cover bolts (disengaged in 1½ turns)

NEC/CEC

CIRCUIT BREAKERS EB SERIES

Protect equipment and personnel from damaging power spikes with the EB Series of circuit

breakers. Explosionproof for Class I, Division 1 locations, these thermal magnetic circuit breakers

provide overcurrent, short circuit protection and safe disconnection.  e EB Series is easy to

operate with positive operating breaker handles that self locate to prevent damage, if the door is

closed without being aligned with the breaker toggle position. Operating stops limit handle travel.

• Breaker handle can be locked in “On” or “O ” position

• Easy mounting

• Wide range of drilled and tapped outlets

• Breaker is trip free of handle

• Wide range of drilled and tapped outlets

• Corrosion-resistant, non-sparking copperfree aluminum with two coats of epoxy powder

coat  nish

• Interior components are removable as an assembly to make wire pulling easier

26

CONTROLS, ENCLOSURES & PANELBOARDS

ATEX/IECEx/NEC/CEC

PANELBOARDS POWERPLEX 304 STAINLESS STEEL PANELBOARD

Appleton’s PowerPlex™ panelboard delivers component level protection that increases hazardous

location safety and  exibility while greatly reducing and simplifying maintenance. It transfers the

 amepath from the panelboard enclosure to individual circuit breaker housings. Its module design

o ers the convenience of  eld replaceable o the shelf breakers. Standard panelboards are cCSAus

certi ed and UL Recognized. Select models are ATEX/IECEx rated. PowerPlex panelboards are

most commonly used for lighting, power, heat tracing, electrical distribution and control, MOV

(motorized operated valve), temporary power and other electrical equipment.

• Field replaceable, standard North American Cutler-Hammer F-Frame or QC Series

circuit breakers

• Lightweight design simpli es installation

• Supplied with standard hard drawn, tin plated copper bus bar allows more wiring space

• Easy access allows for quick, safe and simpler maintenance

• GFI version, 5mA and 30mA, single pole, 40 Amp maximum

• Standard supply with internal actuation. Choice of window or self-aligning external actuation

• Modular design and  exible mounting footprint provide almost endless breaker con gurations

• Optional heaters for extreme cold weather conditions and specially calibrated breakers for

higher ambient

ATEX/IEC

PANELBOARDS INCREASED SAFETY PANELBOARDS

Appleton’s ATX series of increased safety distribution panels are available in IP 66 rated  berglass

reinforced polyester (FRP) or 316L stainless steel and come in multiple sizes depending on the

number of circuits required. Modularity enables coupling together, allowing for additional circuits

and the capability to add main circuit protection. Distribution panels are ATEX approved for use

in locations classi ed as Zone 1-2 and 21-22 locations.

• Cover mounted, oversized lockable knob enables external operation of main and

branch breakers

• Modular designs come in standard sizes and can be interconnected for additional breakers

and main breakers

• Single, 2-, 3-, 4-pole and earth protection (RCD) breakers available up to 690 volts

• Auxiliary contacts available

IEC

PANELBOARDS NEPAC DISTRIBUTION, POWER AND PROTECTION PANEL

Appleton’s Nutsteel NEPAC Series of Ex d IIB panelboards come fully assembled with circuit

breakers and copper bus bar up to 150 Amp interconnected to the internal wiring.  ese

explosionproof panels are designed for powering, distribution and protection of electrical circuits in

Zone 1-2 locations.

• 2-pole or 3-pole circuit breaker up to 125 Amp, IEC 60947-2 standard, breaking capacity:

20 kA at 220/240 V, 10 kA at 400/415 V, 6 kA at 440 V

• 1-pole or 2-pole circuit breakers from 6 to 32 Amp, IEC 60947-2 standard, breaking capacity:

10 kA at 220/240 V (1-pole), 20 kA at 220/240 V (2-pole), 1 OkA at 400/415 V (2-pole),

6 kA at 440 Vac (2-pole)

• Revesteel® anticorrosive coated aluminum body and cover

• Cover  xed with captive screws. All hardware is made of AISI 304 stainless steel

27

CONTROLS, ENCLOSURES & PANELBOARDS

NEC/CEC

PANELBOARDS ALPN SERIES

Compact ALPN panelboards  t into many locations throughout your facility while featuring

a spacious compartment for easy wiring and installation.  e explosionproof and waterproof

ALPN provides a central location for a controlled switching system of large quantities of branch

circuits for lighting, heating, small motors and other similar electrical equipment in hazardous

environments.

• Copper bus bars and Quad-Lead® stainless steel cover bolts are standard

• Padlockable breaker operators

• NEMA 4X rated

• 100 or 225 Amp main lug

NEC/CEC

PANELBOARDS XP SERIES

 e XP Series of pre-wired circuit breaker panelboards protects and controls lighting or heat trace

circuits.  e XP is both explosionproof and watertight for indoor or outdoor use.  e panelboard

and top junction box are factory sealed, eliminating the need for labor intensive  eld wiring and

sealing  ttings. Exclusive rotary slide circuit breaker operators align with breakers in the “On” or

“O ” position when cover is being closed.

• Lockable breakers will not prevent tripping

• Removable hinged cover for easier wiring

• Furnished with bolt-on breakers

• Keyhole mounting lugs simplify mounting

28

PLUGS & RECEPTACLES MAKING CONNECTIONS WHERE YOU NEED THEM

Within the world of hazardous environments, power hungry portable

equipment requires safe, secure and reliable access to power.  at’s why

Appleton’s broad line of plugs and receptacles are designed to eliminate

the possibilities of sparks, arcs and accidental disconnections. We allow

you to connect to the power you need safely, when you need it, over

and over again.

29

With a broad range of power capacities, intermateability with other manufacturers

and a variety of  nish options, Appleton o ers plugs and receptacles for use

throughout your entire facility. But, most importantly, Appleton’s product range is

built upon our determination to keep facilities safe.  at is why we have gone beyond

the NEMA 3X industry standard rating and developed watertight, explosionproof

receptacles that o er NEMA 4X ratings. Our plug designs feature double arc proof

chambers and color coded housings that eliminate the possibility of connecting

plugs into incorrect voltage receptacles. Our receptacles prevent arcing in hazardous

environments with interlocks that guard against accidental disconnection while power

is still being supplied.

30

PLUGS & RECEPTACLES

ATEX/IECEx

PLUGS & RECEPTACLES INCREASED SAFETY POWER SOCKETS AND PLUGS

Appleton’s ATX series of sockets and plugs incorporates added safety features that ensure each plug

insertion and removal does not disturb the explosive atmospheres of Zone 1-2 locations. Available

with a three-pole or four-pole  ameproof cut-out switch with auxiliary early break contact. Plugs

lock when the power is on. Switch handle can be padlocked in the “O ” position. Plug can only be

inserted or removed when the switch is in the “Open” (power o ) position.

• Flameproof cylindrical spigot joint

• Padlocking cover and handle con gurations

• Wide selection of voltages and applications

ATEX/IECEx

PLUGS & RECEPTACLES EXTRA LOW VOLTAGE 16 AMP

Appleton’s ATX series of 16 Amp extra low voltage sockets and plugs deliver increased protection

to industrial environments where durable and rugged equipment is needed.  e polycarbonate

socket and polyamide cover o er impact and corrosion-resistance where the elements, gases or

detergents erode and deteriorate more commonly used materials.

• Color coded by voltage

• Double acting safety device ensures the total disconnection of power when the plug is removed

• Automatically disconnects each phase in a  ameproof chamber

ATEX/IEC

PLUGS & RECEPTACLES FLAMEPROOF POWER SOCKETS AND PLUGS

Appleton’s ATX series of power sockets and plugs guards against arcing with locking receptacles and

 ameproof disconnection chambers. Plugs cannot be removed with the power on. Disconnections

are completed within single or dual  ameproof chambers before the plug is removed from the

socket. Aluminum alloy  ameproof plugs can be used with IEC 60309-2 industrial pin sockets

outside hazardous environments. Heavy duty 80 Amp and 125 Amp models o er a cast iron wall

mounted socket that is  tted with a load break isolating switch.

• Color coded by voltage

• Available padlockable covers and handles

31

PLUGS & RECEPTACLES

NEC/CEC

PLUGS & RECEPTACLES POWERTITE® SERIES

Appleton’s Powertite Series of plugs and receptacles delivers power in hazardous conditions with

rugged construction that provides a watertight, explosionproof or dust-ignitionproof connection.

 is workhorse of the Appleton plugs and receptacles line is made from non-corrosive, copperfree

aluminum and features a NEMA 4X rating. Powertite plugs and receptacles are easily adapted to

reverse service in the  eld through a simple screw lock that connects the plug housing and interior.

• Available in 30, 60, 100, 200 and 400 Amp capacities

• Floating type plug terminal self-aligns to receptacle contacts

• Two grounding styles

• Arc snu ng chamber

• Special polarization available to prevent plug insertion in a receptacle wired for

di erent voltages

NEC/CEC

PLUGS & RECEPTACLES EBR SERIES

EBR receptacles feature a circuit breaker and an externally mounted switching mechanism.  e

EBR mechanically locks the plug in the receptacle when the circuit breaker is in the “On” position.

 is prevents accidental disconnection and protects against short circuit and thermal time delay

overload. Cover mounted components leave the entire enclosure space free for pulling of line

conductors and wiring.

• Breaker handle can be locked in the “On” or “O ” position

• ¾” threaded openings in the top and bottom for optional drain and breather

• Receptacle is prewired to the load side of breaker

NEC/CEC

PLUGS & RECEPTACLES U-LINE®

 e U-Line Series is a robust, explosionproof and dust-ignitionproof plug and receptacle. A

neoprene gasket seals out dust, vapors, dirt and moisture while the plug is engaged. Plugs are

longer and have  nger grips for easier plug insertion and withdrawal. U-Line plugs also feature a

heavy duty cable grip that exceeds UL 150 lb pull out test and engages with an audible click, so

that the operator knows the connection has been made.

• Plug mates with competitive receptacles

• Grounding through extra pole and shell for added safety

• Brass contacts feature a unique design that exerts constant pressure along entire contact surface

for a superior power connection

• Rated 20 Amp, 125 Vac

NEC/CEC

PLUGS & RECEPTACLES FSQC

Interlocked receptacles o er NEMA 4X corrosion resistance and superior electrical performance in

a highly compact FSQC form factor. Durable and safe receptacles for retro t or to meet existing

speci cations for expansion projects o er more capabilities, such as auxiliary contacts for signaling

your process control system when a plug is energized or de-energized.  e FSQC provides best

in class safety with Appleton’s interlocking plug system, arc quenching and containment features,

special polarization option, and suitability for Class I, Division 1 and 2, Group B locations.

• Supplied as standard with both spring door cover for convenient weather resistance (NEMA 3,

3R) and a screw-on cover for NEMA 4X applications.

• Interlocked disconnect switch ensures that the plug cannot be removed or the access cover

opened, while under load.

• UL Listed for use with Appleton’s innovative Powertite ACP plugs and UL Classi ed for use

with competitors’ plugs.

32

CABLE GLANDS,

CONNECTORS & FITTINGS DISTRIBUTING POWER TO WHERE YOU NEED IT

Running cable and conduit throughout Division 2, Zone 2 facilities

demands a wide range of products that meet your needs for both

today and tomorrow. Whether it is designing a new facility, adding

production capacity to an existing plant, or recon guring current

equipment needs, Appleton has cable glands, conduit connectors and

 tting products that help you run electrical power to where it’s needed.

33

Appleton o ers the most expansive and complete product line of cable glands,

conduit connectors and  tting products in the industry.  ere is not a cable or

conduit in the world that cannot be terminated with an Appleton product. We

manufacture alternative designs for specialty applications and customer preferences.

Appleton o ers products constructed of standard brass, stainless steel, cast iron or

aluminum. Additionally, brass cable glands can be nickel plated for extra corrosion-

resistance.

Appleton has also advanced the safety of cable seals with revolutionary designs. Our

proprietary seals displace as the gland is tightened, preventing damage to the cable

sheathing and eliminating the “cold  ow” caused by conventional compressions seals.

34

CABLE GLANDS, CONNECTORS & FITTINGS

ATEX/IEC/NEC/CEC

CABLE GLANDS &

CONNECTORS T3CDS SERIES

 e T3CDS  ameproof Ex d and increased safety Ex e brass cable glands come in sizes to  t all

types of armored and braided cables.  e T3CDS creates a  ameproof seal on the cable inner

sheath and an environmental seal on the cable outer sheath, while eliminating cable damage and

cold  ow.  e T3CDS is approved for use in locations classi ed as Zone 1-2 and 21-22.

• Electroless nickel plated brass, standard

• Continuous operating temperature range from -60°C to +130°C (-76°F to +266°F)

• Reversible armored clamping cone and bi-directional clamping ring accommodates SWA

cables, SWB cables, STA cables and wire braid

ATEX/IEC/NEC/CEC

CABLE GLANDS &

CONNECTORS PX2KX SERIES

 e PX2KX Series of brass cable connectors provides mechanical retention and electrical continuity

for unarmored cables.  e PX2KX Series is also suited for robust environments with an internal

sealing ring that prevents the ingress of dust and moisture. Cable inner cores are sealed with a

 ameproof compound to retain the integrity of electrical systems in hazardous environments.

• Electroless nickel plated brass, standard

• Comprehensive range of sizes and rating approvals

• Continuous operating temperatures range from -20°C to +100°C (-4°F to +212°F)

• Additional certi cations include CSA, GOST and Marine

ATEX/IEC/NEC/CEC

CABLE GLANDS &

CONNECTORS TRAY CABLE CONNECTORS

Appleton o ers a broad line of tri-rated tray cable connectors for use with TC, ITC, PLTC and

other types of tray cable.  e unique compensating displacement seal provides ingress protection

to NEMA 4X and IP 68. Available in aluminum, stainless steel and nickel plated brass, Appleton

tray cable connectors meet the exacting demands of highly caustic or harsh environments, such as

food processing, petrochemical, wastewater treatment, pulp and paper or chemical manufacturing

facilities

• Continuous operating temperature range of -60°C to +110°C (-76°F to +230°F)

• Available in trade sizes ½” through 4”

• Feature a unique seal insert that enables each gland size to terminate the widest cable range

available in a single hub size

• Jacket sealing technique: compensating displacement seal, cable outer jacket

• NPT threads standard, metric available as an option. Other options include adaptor/reducer

and earth tag

• ½” through 1” connectors ship with aluminum locknut standard. Locknuts for larger sizes

must be sourced separately

35

CABLE GLANDS, CONNECTORS & FITTINGS

ATEX/IEC/NEC/CEC

CABLE GLANDS &

CONNECTORS TMC2X SERIES

Whether you are installing one connection or one thousand, Appleton TMC2X cable connectors,

sealed with RapidEx high-speed gel, o er explosionproof protection every time. RapidEx’s unique

low-viscosity formula has excellent cavity adaptation and surrounds each individual conductor,

leaving no voids.

• Designed for use with MC/MC-HL, corrugated interlocked aluminum/steel armor, or

continuously welded armor cables

• Provide a means for terminating jacketed type MC cable, forming a mechanical watertight

connection and providing ground continuity for cable armor

• For use on horizontal or vertical runs

• Simpli ed two piece design

• Utilizes RapidEx high speed liquid resin sealing compound. Sold separately, unit volume

dependant upon TMC2X catalog number ordered

• Independent sealing and armor clamping

• True 360º grounding

• Removable cable armor end stop accommodates larger insulated conductors.

• Superior pull out prevention

• Compact slim pro le

• Widest cable acceptance range

• Disconnectable design

• Additional integral deluge proof seal for protection in extreme o shore and onshore

environments

• Continuous operating temperature -60°C to +85°C (-76°F to +185°F)

IEC

CABLE GLANDS &

CONNECTORS A2F SERIES

Unarmored cables can be terminated with the A2F cable gland.  e A2F is rated for both

 ameproof Ex d and increased safety Ex e applications. It is designed for outdoor use providing

sealed protection against harsh weather and dust.  e A2F is approved for use in locations classi ed

as Zone 1-2 and 21-22.

• Optional integral entry thread seal available

• Electroless nickel plated brass, standard

• Superior sealing with compensating displacement seal

• Suitable for ambient temperatures ranging from -60°C to +130°C (-76°F to +266°F)

• Use indoor and outdoor

• Additional certi cations include CSA, GOST and Marine

36

CABLE GLANDS, CONNECTORS & FITTINGS

NEC/CEC

CABLE GLANDS &

CONNECTORS TMC2 SERIES

 e TMC2 Series of cable connectors can be used in Class I, II and II locations.  ey are

designed for use with following MC/MC-HL, corrugated interlocked aluminum/steel armor,

or continuously welded armor cables.  e TMC2 connectors provide a means for terminating

jacketed type MC cable by forming a mechanical watertight connection and providing ground

continuity for cable armor.

• Simpli ed two piece design with compact slim pro le reduces installation time

• Integral O-ring face seal providing NEMA 4X and IP 68

• Independent sealing and armor clamping

• True 360° grounding

• Removable cable armor end stop accommodates larger insulated conductors

• Superior pull out prevention.

• Widest cable acceptance range.

• Additional integral deluge proof seal for protection in extreme o shore and onshore

environments.

• Continuous operating temperature -60°C to +110°C (-76°F to +230°F)

37

CABLE GLANDS, CONNECTORS & FITTINGS

NEC/CEC

CABLE GLANDS &

CONNECTORS TMCX SERIES

 e TMCX explosionproof, dust-ignitionproof connector features a gas block and epoxy seal for

use in hazardous environments. It uses an exclusive union sleeve that simpli es installations and

guarantees the reusability of connectors when doing repair or replacements.  e TMCX o ers

stainless steel grounding springs for positive ground continuity and excellent pull out resistance,

additional integral deluge proof seals for protection in extreme o shore and onshore locations, and

the widest cable acceptance range in the industry.

• Available in copperfree aluminum, nickel plated brass or stainless steel

• Watertight NEMA 4X

• True 360° grounding

• Independent sealing and armor clamping

• Compact and slim pro le

• Rated for Class I, Class II, Class III, Class I, Zone 1. AEx d IIC, Class I, Zone 1

Ex d IIC

• Cable Type - MCHL - corrugated/interlocked, aluminum/steel armor and continuously welded

armor cables (e.g. Teck, CLX)

• Metric options available

38

CABLE GLANDS, CONNECTORS & FITTINGS

ATEX/IEC/NEC/CEC

CONDUIT FITTINGS FLEXIBLE COUPLINGS

Di cult bends, tight spaces, vibration and movement that challenge rigid conduit connections can

be negotiated with Appleton’s explosionproof, dust-ignitionproof, watertight  exible couplings.

 ese bronze or stainless steel couplings are watertight and come with an inner core and insulating

liner. Each coupling o ers the electrical conductivity of rigid conduit, which negates the need for

an external bonding jumper.

• Accurately tapped and tapered threads for tight, rigid joints

• Interior insulating liner protects wires from vibration induced abrasion

• Watertight

• No bonding jumper

NEC/CEC

CONDUIT FITTINGS UNY AND UNF UNION UNILETS®

UNY and UNF explosionproof, dust-ignitionproof unions come in expansion and non-expansion

versions for joining conduit and a xing conduit to enclosures in hazardous atmospheres.  ese

unions feature a concentric ring interlocked design that creates a slim external casing for use in

tight spaces, such as around pumps and motors. Expansion unions’ one piece design eliminates the

need for disassembly during installation and includes an internal bronze contact grounding spring

that ensures a positive ground connection.

• Facilitates modi cations and removal of enclosures without turning or removal of conduit

• Expansion unions with telescoping cylinder come in standard and long models (½”-1”)

• Unions come in standard sizes (½”-6”)

• Expansion unions do not require bonding jumper

NEC/CEC

CONDUIT FITTINGS SEALINGS FITTINGS

Maintain the integrity of Class I, Division 1 and 2 locations with Appleton’s extensive range of

explosionproof, dust-ignitionproof sealing  ttings. Vertical and horizontal applications are available

in a variety of  nishes, including Appleton’s triple coat  nish of zinc electroplate, chromate and

epoxy powder coat. Materials include high strength malleable iron, breakout Grayloy®-iron and

corrosion-resistant aluminum. Sealing  ttings come in 25%  ll for greater wire capacities and 40%

 ll for more economical installations.

• Sizes range from ½” to 6”

• Access cover for drain seal  ttings automatically channels any water that has accumulated

above the seal

39

CABLE GLANDS, CONNECTORS & FITTINGS

NEC/CEC

CONDUIT FITTINGS CAPPED AND PULLING ELBOWS

Appleton’s explosionproof capped and pulling elbows  t a wide range of Class I and II rated

locations, endure exposure to corrosion accelerating agents and maintain the integrity of an

explosionproof electrical system.  e capped elbow models function as sealing  ttings when used

with sealing covers that also feature pry notches for easy opening. Elbows feature exclusive integral

rollers that make pulling easier.  e ELBD Series’ body and cover feature ground mated surfaces to

meet classi ed location requirements.  e ELBY Series’ threaded cover openings permit easy access

for pulling conductors through hubs.

• Malleable iron bodies with copperfree aluminum covers have high tensile strength and ductility

• Smooth and rounded integral bushings protect conductor insulation

• Accurately engineered  ame pathways ground into mating surfaces or threads

NEC/CEC

CONDUIT FITTINGS UNILET® CONDUIT OUTLET BODIES

Whether it is new construction, modi cations or renovations, Appleton has a conduit outlet body

for any place wires are accessed or conduits change direction.  e full range of conduit outlet

bodies  ts every application and footprint available with large interiors for easier maneuvering and

accurately tapped, tapered threads for tight rigid joints and excellent ground continuity.

• Select series are interchangeable with other manufacturer conduit bodies

• Smooth, rounded and internal bushings prevent wire damage and easy pulling

• Available in malleable iron, aluminum and Grayloy®-iron for lightweight,watertight, corrosion-

resistant and impact-resistant applications

• Stainless steel cover screws

• Form 35 features integral rollers on 1-1/4” to 4” trade sizes to facilitate easier pulling

• Appleton Form-IN-Place integral covers with gasket for FM7, FM8, and FM9 conduit bodies

40

HEAT TRACE SYSTEMS GLOBAL PROCESS HEATING SOLUTIONS

Whether it is simple freeze protection or complex process maintenance,

we can provide a rugged heat trace system that is reliable, e cient and

smart.

41

Nelson Heat Trace heating cables, control and/or monitoring and accessories have

been manufactured for every imaginable con guration, location and purpose. Our

trouble free, e cient and cost e ective systems are used around the globe. Compatible

with all brands of heaters, our control systems o er the world’s most advanced heat

trace system management.

Our experienced team can provide comprehensive guidance on con guring a heat trace

system that will optimize the power and cost e ciencies.

42

HEAT TRACE SYSTEMS

ATEX/IEC/NEC/CEC

HEAT TRACE SYSTEMS SELF-REGULATING HEATER CABLES

Nelson provides self-regulating heating cables for both freeze protection and process maintenance

applications. Our cables are tested and certi ed to ensure the highest quality even in the harshest

of environments.  ese heater cables can be  eld cut-to-length and feature multiple power output

and voltage ratings.

• 120 thru 277 volt ratings

• 3 thru 20 watts per foot power outputs

• Various con gurations available

• Maintenance temperatures up to +121°C (+250°F)

• Lower energy consumption

• Certi ed for ordinary, Division and Zone hazardous locations

ATEX/IEC/NEC/CEC

HEAT TRACE SYSTEMS MINERAL INSULATED HEATERS

Nelson pioneered the use of mineral insulated heating cables for industrial applications that require

higher temperatures, extended heater life and e cient power output. With one or two heating

elements surrounded by magnesium oxide insulation, maximum exposure temperatures of +593°C

(+1,100°F) are possible. Wrapped in a corrosion-resistant alloy 825 sheath, MI heating cables

feature excellent chemical resistance, including immunity from harsh chloride stress corrosion.

Nelson’s unique manufacturing process results in a product that is superior in durability,  exibility,

and ease of installation.

• Voltages up to 600 Vac

• Power outputs to 70 watts per foot

• Maintenance temperatures up to +371°C (+700°F)

• Uniform diameters of 4.8 mm and 7.9 mm (.19 in and .31 in)

• Highly  exible, easy to install

• Certi ed for ordinary, Division and Zone hazardous locations

ATEX/IEC/NEC/CEC

HEAT TRACE SYSTEMS TERMINATION KITS

Nelson can provide a wide range of connection systems to meet the global installation requirements

for Zone and Division locations. Manufactured using the highest quality materials, these systems

are designed to handle the wide temperature ranges and chemical exposures found in today’s

industrial facilities. Pipe mounted and component based connections meet the stringent demands

for heat trace applications.

• Power, splice and tee splice connections

• Above the insulation end terminations for accessibility

• Optional end of circuit indicating lights use LED lamps for reliability and long life

• Complete line of installation accessories

• Certi ed for ordinary, Division and Zone hazardous locations

43

HEAT TRACE SYSTEMS

NEC/CEC

HEAT TRACE SYSTEMS CM-2001 SINGLE POINT CONTROL/MONITORING SYSTEM

For stand alone or networked heat tracing applications, the CM-2001 is Nelson’s most versatile

control and monitoring system.  is microprocessor based controller allows operational personnel

to control the line temperature, as well as monitor various conditions such as voltage and current

alarms, ground fault leakage and trip conditions, and sensor and communication failures.  e

CM-2001 is housed in a NEMA 4X enclosure that is certi ed for ordinary, Division and Zone

locations. Simple integration into existing systems is assured with the ability to connect 32

individual systems per node and compatibility to Nelson’s CM.COMM software or any Modbus

compatible device.

• User selectable control modes

• Easy to read display for quick and clear communications

• Dual RTD inputs with user selectable operations

• Programmable auto test feature

• For use in hazardous and ordinary locations

NEC/CEC

HEAT TRACE SYSTEMS CM-332 MULTI-POINT CONTROL/MONITORING SYSTEM

One of the most advanced control and monitoring systems available, the CM-332 is a

microprocessor based control and monitoring system based on standard industrial automation

products speci cally integrated for use with electric heat tracing systems. Nelson’s CM-332 system

provides temperature and current monitoring for each heat tracing circuit while communicating

additional information to operations personnel such as temperature alarms, circuit faults, and

sensor failure and communications failures.

• Color touchscreen operator interface

• Compatibility with existing facility automation systems

• Complete temperature monitoring

• Complete heater cable monitoring

• Con gurable circuit management alerts

• Con gurable system trouble alarms

• Global programming of all control and alarm functions

• Programmable auto test feature

• Worldwide product support

• Certi ed for ordinary and Division 2 hazardous locations

• Ethernet and Modbus communication options available

44

POWER QUALITY

SOLUTIONS ENSURING CLEAN POWER QUALITY THROUGHOUT YOUR FACILITY

Maintaining clean, continuous power is critical to plant safety and

production. Power anomalies, such as voltage irregularities, brownouts

and blackouts, create equipment failures that lead to costly downtime

and compromised safety.  ey also a ect data corruption and loss in

both computers and computer controlled equipment. SolaHD manages

power anomalies with a full line of power quality solutions.

45

SolaHD’s power quality solutions are designed to ensure optimum production

performance and workplace safety by protecting, converting and supplying power across

your facility. SolaHD’s transformers smooth the stream of power entering the plant’s

service inlet. Our surge suppressors, power conditioners, transformers and power supplies

clean and support power throughout the branch distribution. SolaHD’s line reactors,

power supplies and uninterruptible power supplies (UPS) maintain the right voltage level

to keep computer equipment and production lines humming along.

SolaHD equipment also meets the needs of industrial locations with encapsulated power

supplies and transformers that surpass NEMA standards, along with a range of products

rated for  ammable atmospheres.

Depend on SolaHD’s power quality solutions for controlled, reliable power throughout

your plant. We are there, from service entrance to branch panel to point of use, to protect

production with power that is always on and ready to be used.

46

POWER QUALITY SOLUTIONS

ATEX/IEC/NEC/CEC

POWER QUALITY

SOLUTIONS SDN™ POWER SUPPLY SERIES

SolaHD’s line of SDN power supplies provides industry leading performance across a wide breadth

of applications and uses.  ese power supplies have been engineered for the demands of hazardous

locations with a wide operation temperature range, reliable performance, and high tolerance to

shock and vibration.  e SDN Series meets the European directive with power factor correction.

SolaHD is a member of the Open DeviceNet Vendors Association and has designed certain SDN

models for DeviceNet applications.

• Select models are ATEX approved

• Adjustable output voltage

• No internal fan, no extra cooling required in any power level

• Auto select 110/230 Vac, 50/60 Hz Input

• Operating temperatures range from -10°C to +60°C (+14°F to +140°F)

• Powers high inrush loads without shutdown or foldback

• Inde nite short circuit, over voltage and over temperature protection

• DC OK signal

• Highly e cient >90% switching capability

ATEX/IEC/NEC/CEC

POWER QUALITY

SOLUTIONS SCP-X SERIES

 e SCP-X Series is an enclosed IP 66/67 and NEMA 4X rated power supply for stand alone

operations.  is series operates within -40°C to +60°C (-40°F to +140°F) without derating and

features quick change connectors for fast hook ups.  e SCP-X’s metal housing also reduces costs

over having separate housings.

• Worldwide approvals

• Universal input

• Can be mounted in any orientation without limitation

• DC OK green LED

• ATEX approved

47

POWER QUALITY SOLUTIONS

NEC/CEC

POWER QUALITY

SOLUTIONS ENCAPSULATED TRANSFORMERS

SolaHD’s encapsulated transformers are available in di erent con gurations for hazardous locations

and harsh weather environments. Rugged NEMA 3R enclosures are rated for Class I, Division/

Zone 2 locations. SolaHD’s low temperature rise designs incorporate a +220°C (+428°F) insulation

system for critical applications that mandate extra overload capacity, power conservation and cooler

operating temperatures.  eir temperature rise of only +80°C or +115°C (+176°F or +239°F)

under full nameplate load produces 13% to 21% less power loss than conventional +150°C

(+428°F) rise units which results in lower running costs and increased reliability. Fully enclosed,

non-ventilated designs (TENV) are also available.

• Available NEMA 12, 4X and stainless steel enclosures

• Weather shields

• UL-3R enclosure for indoor or outdoor service

• Copper lead wire terminations

• Wall mounting brackets (500 lbs maximum)

• Copper wound, open core and coil designs

• Generously sized wiring compartments

NEC/CEC

POWER QUALITY

SOLUTIONS POWER CONDITIONERS

Protect sensitive equipment from damage, degradation or misoperation with SolaHD’s power

conditioners and voltage regulators.  e MCR line regulates the power going to sensitive

equipment while providing superior noise  ltering and surge protection. Dirty power is no

longer caused by impulses, swells, sags, brownouts and waveform distortions. MCR’s hardwired

and portable designs increase the actual Mean Time Before Failure (MTBF) with SolaHD’s

ferroresonant design. Surge protection is tested to ANSI/IEEE C62.41 Class A and B Waveform:

<10 V let through typical.

• Noise attenuation: -120 dB common mode, -60 dB transverse mode

• Harmonic  ltering

• Hardwired series acts as a step-up or step-down transformer

• Galvanic isolation provides exceptional circuit protection

• Hardwired or portable for point-of-use protection

• 25 year typical MTBF

• No maintenance required

• ±3% output voltage regulation

The world’s leading manufacturing and process facilities turn to Appleton as the trusted source of electrical products. We have earned that trust

by committing over a century of expertise, and the resources of engineers around the globe, to the pursuit of safety and ef ciency. It re ects our

dedication to maintaining the highest production standards and rigorously testing above and beyond what is required. That trust also powers our

continuous development and innovation of state of the art technology and revolutionary products.

Turn to Appleton when it is time to safely illuminate work operations among explosive fumes, deliver power to critical production machinery and

keep pipelines warm in the unforgiving frost. Turn to Appleton when the  rst time is the only time to get it right.

Appleton is your trusted industrial electrical products brand. See our full line of electrical products for around the globe by visiting us at

www.egseg.com.

Appleton is our premium line of industrial

electrical products under EGS Electrical

Group, a division of Emerson Industrial

Automation.

Emerson Industrial Automation brings

integrated manufacturing solutions to

diverse industries worldwide. Our

comprehensive product line, extensive

experience, world-class engineering and

global presence enable us to implement

solutions that give our customers the

competitive edge.

For over 150 years, our electrical product

brands have been providing a rich

tradition of long-term, practical, high

quality solutions with applications ranging

from the construction and safe operation

of petrochemical and process plants to

providing quality power that precisely

controls automotive robotic production.

Engineers, distributors, contractors,

electricians and site maintenance

professionals around the world trust

Emerson Industrial Automation brands

to make electrical installations safer,

more productive and more reliable.

EGS is organized into three focused

businesses that provide distributors

and end-users expert knowledge and

excellent service.

Electrical Construction Materials

This group manufactures a broad range

of electrical products including conduit

and cable fi ttings, plugs and receptacles,

enclosures and controls, conduit bodies,

and industrial lighting. Whether the

application is hazardous location, industrial,

or commercial, the ECM group has the

products to meet your needs.

Power Quality Solutions

This group offers the broadest power

quality line including UPS, power

conditioners, voltage regulators, shielded

transformers, surge suppression devices

and power supplies.

Heating Cable Systems

This group offers a broad range of electri cal

heating cable products for residential,

commercial, and industrial applications.

Electrical Construction Materials

Power Quality Solutions

Heating Cable Systems

The Appleton, O-Z/Gedney, SolaHD, EasyHeat, Nelson and Emerson logos are registered in the U.S. Patent and Trademark Of ce.

All other product or service names are the property of their registered owners. © 2012, EGS Electrical Group, LLC. All rights reserved.

EGS Electrical Group

9377 W. Higgins Road

Rosemont, IL 60018

1.800.621.1506

www.egseg.com

Asia/Paci c

65.6891.7600

Brazil — Camaçari/BA

55.71.3623.2028

Europe

33.3.2254.2759

Australia

61.3.9721.0348

Canada

888.765.2226

Mexico/Latin America

52.55.5809.5049

Brazil — São Paulo/SP

55.11.2122.5777

China

86.21.3418.3888

Middle East/Africa/India

971.4.811.8100