Installation Directions

Instruction Sheet Vrcs4-Mr Instruction_Sheet_VRCS4-MR Instruction_Sheet_VRCS4-MR 516 docs z-wave-assets

2014-05-16

: Pdf 612780-Installationsheet 612780-InstallationSheet 078477 Batch3 unilog

Open the PDF directly: View PDF PDF.
Page Count: 2

WARNINGS AND CAUTIONS:
• ON/OFFLEDforremoteloadstatus.
• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.
• Ifyouareunsureaboutanypartoftheseinstructions,consultanelectrician.
• Recommendedminimumwallboxdepthis2-1/2".
WARNINGS AND CAUTIONS:
•
Maximumwirelengthfromdimmertoallinstalledremotescannotexceed300ft(90m).
• Disconnectpoweratcircuitbreakerorfusewhenservicing,installingorremovingxture.
• Usethisdeviceonlywithcopperorcoppercladwire.
4-Scene Controller with Switch - Single Pole (One Location)
Cat.No.VRCS4-MR,120/240VAC,50/60Hz
Incandescent-1800W–MagneticLow-Voltage-1800VA(1440W)
ElectronicLow-Voltage-1800W–Fluorescent-1800VA–Supplemental-1/2HP
INSTALLATION INSTRUCTIONS
Tools needed to install your device
Slotted/PhillipsScrewdriver ElectricalTape Pliers 
Pencil   Cutters  Ruler
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
ONOFFONOFF
ONOFF
ONOFF
ONOFF
ONOFF
WARNING: TO AVOID FIRE, SHOCK OR DEATH; TURN
OFF POWER atcircuitbreakerorfuseandtestthatpowerisoff
beforewiring!
Step 1
5/8"
(1.6 cm) Strip Gage
(measure bare
wire here)
Cut
(if necessary)
WIRING DEVICE:
Connect wires per WIRING DIAGRAM as follows:
• GreenorbarecopperwireinwallboxtoGreenterminalscrew.
• LineHotwallboxwiretoterminalscrewmarked"BK".
• LineNeutralwallboxwiretoterminalscrewmarked"WH".
• Loadwallboxwiretoterminalscrewmarked"RD".
Wiring Application:
Hot (Black)
Neutral (White)
Line
120/240 VAC
50/60 Hz
BKWH
Green
Ground
4-Scene Controller w/ Switch
Load
RD
WH
Step 4
2
4
1
3
1.Line(Hot)
2.Neutral
3.Ground
4.Load
Identifying your wiring application (most common):
NOTE:Ifthewiringinyourwallboxdoesnotresemblethis
conguration,consultaqualiedelectrician.
Step 2
INTRODUCTION
Leviton’sViziaRF+TMcomponentsaredesignedtocommunicate
witheachotherviaRadioFrequency(RF)toprovideremotecontrol
ofyourlighting.UsingRFtechnologyallowsLevitontoprovidethe
greatestsignalintegritypossible.EachmoduleinLeviton’sViziaRF+TM
componentlineisaZ-Wave®enableddevice.InaZ-Wave®network,
eachdeviceisdesignedtoactasarouter.Theserouterswillre-transmit
theRFsignalfromonedevicetoanotheruntiltheintendeddevice
isreached.Thisensuresthatthesignalisreceivedbyitsintended
devicebyroutingthesignalaroundobstaclesandradiodeadspots.
This4-SceneControllerismeanttocontrolspecialsceneenabled
Z-Wave®products.Tocontrolgroupsofdevicesthataremixedordo
notsupportscenecommandclassusetheLeviton4-ZoneController
(VRCZ4).Settingupthisdevicerequiresspecicadvancedcontroller
functionalities,yourcontrollermustbeabletoassociatedevicetogroups
andmustbeabletocontrolthescenecontrollercongurationcommands
suchastheadvancedProgrammingRemote(VRCPG).
• SwitchON/OFF
• SceneCapable
• ThisisaZ-Wave®Controller
• Scenecontrolwithouttravelerwires
• Cancall4scenes
• Cancontrolasingleload
• ON/OFFLED
• Twowaycommunication
• RFreliability
• Easeofinstallation–Nonewwiring
• CompatiblewithotherZ-Wave®enableddevices
FEATURES NOTES:
• Ifusinganon-LevitonProgrammer/Remote,refertothe
Programmer/Remoteinstructionsheet.
• 4-ScenecontrollersincudedintoaZ-Wave®networkmustbe
updatedafteryouhaveincludedallotherdevices.
• IfusingtheVRCPGInstallChecklistfeature,gotostepC.
A) IfusingaLevitonZ-Wave®Programmer/Remote,Cat.No.VRCPG,
presstheMenubuttonandscrolldowntoSystemSetup.Press
thecenterbuttontoselectSystemSetupMenu.ChooseAdvanced
Settings.PressthecenterbuttontoselectNetwork.Pressthecenter
buttonto<IncludeNode>.
B) IfusingVRCPGProgrammer/Remote,youwillbepromptedtoplace
4-Scenecontrollerintoprogrammingmode.
C) ToaccessProgrammode,pressandhold
buttons1and3(refer to figure).Wait
5secondsuntiltheLEDturnsAmber.
ReleasethebuttonsandtheLEDwillblink
Amber.YouarenowinProgrammingmode.
NOTE:IftheLEDonthe4-scenecontroller
turnssolidRedwhileincluding,therehas
beenacommunicationerror.
D) Whilestandingclosetothe4-Scene
controller(approximately1ft.),pressthe
centerbuttonontheProgrammer/Remote
to<Include>deviceinthenetwork.
NOTE:Onlyonedevicemaybeincludedat
anytime.
E) ThePrimaryProgrammer/RemotewillassignaHomeIDand
NodeIDforthisdevice.
NOTE:ThisinformationwillbestoredintheProgrammer/Remote
tobeusedforfuturereference.
NOTE:Youmaynameoredityourdeviceatthistime.
F)
The 4-Scene controller is now installed in the network. If using
VRCPG you will be prompted to include switch, otherwise,
please proceed to Step G to include switch.
Step 8 Including 4-Scene Controller with Switch
into Z-Wave® Network:
Changing the color of your device:
Your4-Scenecontrollerwithswitchincludesthreecoloroptions.The
controllershipswiththeWhiteframeattached.Tochangecolorofframe,
proceedasfollows:
Line up tabs
and press in
side to attach
Push in
side at tab
to release
Afterframeisremoved,removeexistingpushbuttonsandreplacethem
withdesiredcolorchangepushbuttons.TochangetheDIM/BRIGHTbutton,
beforemountingframe,pressoutDIM/BRIGHTbutton(bottom)frombackof
frameandpressinfromfrontofframenewDIM/BRIGHTbutton.TomakeIR
capable,replacewithaDIM/BRIGHTbuttonthathastheIRwindow.
INSTALLING YOUR 4-SCENE CONTROLLER W/ SWITCH
NOTE:UsecheckboxeswhenStepsarecompleted.
Step 3 Preparing and connecting wires:
This4-Scenecontrollerwithswitchcanbewiredusingside
wireterminalscrewsorthroughbackwireopenings.Choose
appropriatewirestrippingspecicationsaccordingly.
• Positionallwirestoprovideroomin
outletwallboxfordevice.
• Ensurethattheword“TOP”isfacingup
ondevicestrap.
• Partiallyscrewinmountingscrewsin
wallboxmountingholes.
NOTE:Dresswireswithabendas
shownindiagraminordertorelieve
stresswhenmountingdevice.
• Restorepoweratcircuitbreakerorfuse.
• LEDshouldturnON.
• Togglebutton1ON/OFFtotestlocal
loadoperation.
If LED or LOAD does not turn ON,
refer to the TROUBLESHOOTING
section.
Testing your device prior to mounting in wall box:
Step 5
• Makesurethattheendsofthewiresfromthewallboxare
straight (cut if necessary).
Back Wire (either hole may be used)
Backwireopeningsaccept
#14-12AWGsolid wire copper only.
Side Wire Connection
Sidewireterminalsaccept#14-12
AWGsolid wire copper only.
Bl
Installationmaynowbecompletedbytightening
mountingscrewsintowallbox.Attachwallplate.
Device Mounting:
TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE.
Step 6
Restore Power:
Restorepoweratcircuitbreakerorfuse.
Installation is complete.
Step 7
Step 3 cont'd
DI-010-VRCS4-02A
DI-010-VRCS4-02A©2009LevitonMfg.Co.,Inc.
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
LevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenetofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforveyearsfromthepurchasedate.Leviton’sonlyobligationistocorrectsuchdefectsbyrepairorreplacement,
atitsoption,ifwithinsuchveyearperiodtheproductisreturnedprepaid,withproofofpurchasedate,andadescriptionoftheproblemtoLeviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, New York 11747.Thiswarrantyexcludesandthereisdisclaimedliabilityforlabor
forremovalofthisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperlyorinanimproperenvironment,overloaded,misused,opened,abused,oralteredinanymanner,orisnotusedundernormaloperatingconditionsornotinaccordancewithanylabelsorinstructions.There are no other or implied
warranties of any kind, including merchantability and fitness for a particular purpose,but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and tness for a particular purpose, is limited to ve years. Leviton is not liable for incidental,
indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation.Theremediesprovidedhereinaretheexclusiveremediesunderthiswarranty,whetherbasedoncontract,tortorotherwise.
Including 4-Scene Controller with Switch
into Z-Wave® Network:
Step 8 cont'd Step 9 Excluding 4-Scene Controller with Switch from
a Z-Wave® Network:
For additional information, contact Leviton’s
Techline at 1-800-824-3005 or visit Leviton’s
website at www.ViziaRFplus.com
ProtectedunderU.S.PatentNumber6,388,399andpatentspending
andlicensedunderU.S.PatentsNumbers5,905,442,and5,982,103
TROUBLESHOOTING
Load Device/Switch:
• LightsFlickering
- Lamphasabadconnection.
- Wiresnotsecuredrmlyunderterminalscrewsofswitch.
• LightdoesnotturnON
- Circuitbreakerorfusehastripped.
- Lampisburnedout.
- LampNeutralconnectionisnotwired.
Controller/Scene:
• LocatorLEDoncontrollerdoesnotturnON
- Circuitbreakerorfusehastripped.
- If4-ScenecontrollerispoweredupandLEDdoesnotturnON,
 checkwiring.
• SceneControllerdoesnotoperatelights
-Checkassociation.
 -Ensurethatcontrollerwasproperlyupdated.
- Re-programyourscene,andensureeachlightisin
thecorrectON/OFFstate..
• LEDturnssolidRed
-Checkassociation.
 -Ensurethateachdeviceinthenetworkiswithin70ft.(21m)of
 anotherdevice.
Programmer/Remote
Cat. No. VRCPG
NOTE:Programmer/Remotemustbe
incloseproximityto4-Scenecontroller
whenincludinginthenetwork.
Excluding 4-Scene controller:
A) IfusingaLevitonZ-Wave®Programmer/Remote,Cat.No.VRCPG,
presstheMenubuttonandscrolldowntoSystemSetup.Pressthe
centerbuttontoselectSystemSetupMenu.ChooseAdvancedSettings.
PressthecenterbuttontoselectNetwork.Scrolldownto<Exclude
Node>andpressthecenterbutton.
B) IfusingVRCPGProgrammer/Remote,youwillbepromptedtoplace
4-Scenecontrollerintoprogrammingmode.
C) Toaccessprogrammode,pressandholdbuttons1and3(refer to
figure).Wait5secondsuntiltheLEDturnsAmber.Releasethebuttons
andtheLEDwillblinkAmber.Youarenowreadytoexclude.
NOTE:IftheLEDonthe4-ScenecontrollerturnssolidRedwhile
excluding,therehasbeenacommunicationerror.
D) Whilestandingclosetothe4-Scenecontroller(approximately1ft.),
pressthecenterbuttonontheProgrammer/Remoteto<Exclude>
devicefromthenetwork.
Factory Default:
Ifyour4-Scenecontrollerwithswitchisnotresponding,oryouareunableto
controlitafteryouhavetriedtoInclude/Excludeitmultipletimes,itmaybe
necessarytoresetthe4-Scenecontrollerwithswitchtoitsoriginalfactory
settings.Toaccomplishthis,proceedasfollows:
• Onthe4-Scenecontrollerwithswitch(refer to
figure),pressandholdbuttons1and3.Wait
approximately10secondsuntiltheLEDturns
AmberandthenturnssolidRed.AllowLED'sto
blinkredtwice,releasethebuttons.The4-Scene
controllerwithswitchisnowreset.Oncethe
controllerisreset,itwillbenecessarytoRe-
Includeittoanetworkbeforeitcanbeused.
CAUTION:SETTINGADEVICETOAFACTORY
DEFAULTDOESNOTEXCLUDETHATDEVICE
FROMANETWORK.THEEXCLUSION
PROCEDUREMUSTSTILLBEFOLLOWEDTO
REMOVETHEDEVICEFROMTHEPRIMARY
CONTROLLER’SINFORMATIONTABLE.FAILURETODOSOMAY
RESULTINSYSTEMTHATISSLOWTORESPOND,ORMAYFAILTO
RESPONDTOSOMEDEVICES.
Scene Application:
Push Button (Default settings)
Turn ON from OFF position:
Press–Sceneisactivated,SceneLEDturnsON.
LEDwillblinkuntilSceneisreached.
Turn OFF from ON position:
Press–TurnsalllightsinsceneOFF,SceneLEDturnsOFF.
DIM/BRIGHT:
PressleftsideofDim/Brightbutton–LightsinlastactivatedScenewilldim.
PressrightsideofDim/Brightbutton–LightsinlastactivatedScenewill
brighten.
NOTE:ControllerwillonlyDim/Brightdeviceslocatedwithindirectradio
frequencyrange.
NOTE:LEDwillbelitonlywhenall
lightsinscenehavereachedtheir
presetlevel.Ifthereisamanual
changetoanylightinthescene,the
LEDwillturnOFFindicatingthatyou
arenolongerinthatscene.
OPERATION
LED
Push
Button
Dim/Bright
Button
G)Including local Switch:
• RemaininAdvancedSettings.
• PressCenterbuttontoselect<IncludeNode>.
• WhilestandingclosetotheVRCS4(approximately1ft.)pressthe
centerbuttonontheProgrammer/Remoteto<Include>devicein
thenetwork.
• ThePrimaryProgrammer/RemotewillassignaHomeIDand
NodeIDtoyournewswitch.
• Youmaynameoreditthedeviceatthistime.
NOTE:Bydefault,switchwillbecontrolledbyButton1onyourscene
controller.
H) Afteralldevicesareincludedintothenetwork,thecontrollermustbe
updated.Toupdatecontrollerproceedasfollows:
• Ifusinganon-LevitonProgrammer/Remote,refertothe
Programmer/Remoteinstructionsheetforupdatingcontroller.
• IfusingLevitonZ-Wave®Programmer/Remote,Cat.No.VRCPG,
presstheMenubuttonandscrolldowntoSystem.Pressthe
centerbuttontoselectSystem.ChooseAdvanced.Pressthe
centerbuttontoselectAdvancedInstall.Pressthecenterbutton
toselectUpdateController.Selectthecontrollertoupdate.Press
centerButtontobeginupdate.Updatewillstartautomatically.
Standwithin(1ft)ofcontrollerwhileupdatingNetworktopology.
• WaituntiltheVRCPGProgrammer/Remoteconrmscompletion.
Updateisdone.
NOTE:Ifthe4-Scenecontrollerwithswitch
hasbeensuccessfullyIncludedinthe
networkandtheusertriestoInclude
itagainwithoutrstexcludingitfromthe
network,thenodeIDwillremainthesame.
Cat. No. VRCPG
1 ON
2 ON
3 ON
4 ON
OFF
OFF
OFF
OFF
Menu
Button
Center
Button
Scene Programming:
NOTE: Alldevicesassociatedtothebuttonsmustsupport
Z-Wave®scenecommand.Ifadeviceinthegroupdoesnot
supportthescenecommanditwillnotbecontrolled.
•Pressandholddesiredscenebuttonon4-SceneController
untilLEDblinksGreen.
•AdjustanyloadsassociatedtothatbuttonbyturningON/
OFForDim/Brightentheload.
•Pressbuttonagainon4-SceneControllerandtheLEDwill
stopblinking.
•Thescenehasnowbeenset.
Step 11
FCC COMPLIANCE STATEMENT
ThisdevicecomplieswithPart15oftheFCCRules.Operationissubject
tofollowingtwoconditions:(1)thisdevicemaynotcauseharmful
interference,and(2)thisdevicemustacceptanyinterferencereceived,
includinginterferencethatmaycauseundesiredoperationofthedevice.
Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfor
aClassBDigitalDevice,pursuanttoPart15oftheFCCRules.These
limitsaredesignedtoprovidereasonableprotectionagainstharmful
interferenceinaresidentialinstallation.Thisequipmentgenerates,uses,
andcanradiateradiofrequencyenergyand,ifnotinstalledandusedin
accordancewiththeinstructions,maycauseharmfulinterferencetoradio
communications.However,thereisnoguaranteethatinterferencewill
notoccurinaparticularinstallation.Ifthisequipmentdoescauseharmful
interferencetoradioortelevisionreception,whichcanbedetermined
byturningtheequipmentOFFandON,theuserisencouragedtotryto
correcttheinterferencebyoneormoreofthefollowingmeasures:
• ReorientorrelocatethereceivingAntenna.
• Increasetheseparationbetweentheequipmentandthereceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthatto
whichthereceiverisconnected.
• Consultthedealeroranexperiencedradio/tvtechnicianforhelp.
FCC CAUTION
AnychangesormodicationsnotexpresslyapprovedbyLeviton
ManufacturingCo.,Inc.,couldvoidtheuser'sauthoritytooperatethe
equipment.
After inclusion process, you must associate Vizia RF light
switches, to button on the controllers. Refer to the Primary
Programmer/Remote instruction sheet for complete
details.
NOTE:Thissteprequiresacontrollerthatcancreateassociationliststo
specicgroups1-4.
NOTE:One(1)Z-Wave®lightswitchcanbeassociatedtomultiple
controllers(uptove(5)controllersmaximum).
NOTE:Ifusinganon-LevitonProgrammer/Remote,refertothe
Programmer/RemoteinstructionsheetforassociatingaViziaRF+light
switch.
NOTE:YourLocalswitchwillbeassociatedbydefaulttobutton1.
Device Association:
Step 10
Excluding Load Control:
A) IfusingaLevitonZ-Wave®Programmer/Remote,Cat.No.VRCPG,
presstheMenubuttonandscrolldowntoSystemSetup.Pressthe
centerbuttontoselectSystem.ChooseAdvanced.Pressthecenter
buttontoselectAdvancedInstall.Scrolldownto<ExcludeNode>and
pressthecenterbutton.
B) IfusingVRCPGProgrammer/Remote,youwillbepromptedtoplace
LocalRelaySwitchintoprogrammingmode.
C) ToExclude,pressandholdbuttons2and4(refer to figure).Wait5
secondsuntiltheLEDturnsAmber.ReleasethebuttonsandtheLED
willblinkAmber.Youarenowreadytoexclude.
NOTE:IftheLEDontheLoadcontrolturnssolidRedwhileexcluding,
therehasbeenacommunicationerror.
D) WhilestandingclosetotheLoadcontroller(approximately1ft.),press
thecenterbuttonontheProgrammer/Remoteto<Exclude>devicefrom
thenetwork.

Navigation menu