872.876specsheet

2014-11-10

: Pdf 872.876Specsheet 872.876specsheet spec products sterner

Open the PDF directly: View PDF PDF.
Page Count: 2

Job Name: ________________________________
Fixture Type: ______________________________
Job Number: _____________________________
Distributor: _______________________________
Distributor P.O.: ___________________________
HOUSING
The luminaire housing shall be mitre-formed construction from a single piece of 6063-T6
aluminum extrusion, with only a single seam located at the bottom of the housing. The rear
canopy shall be of aluminum sheet that is crimped into a specially designed upper lip of the
sidewall extrusion. This lip shall be lined with an Isocryl gasket prior to the crimping process
to form a fully sealed canopy without the use of silicone or welds.
LENS & DOORFRAME
The luminaire lens shall be clear tempered glass, 0.188” thick, thermal and impact resistant.
Lens shall be set into a mitre formed extruded aluminum doorframe which is secured by
(6) self-retained stainless steel fasteners. Lens and doorframe are gasketed by an extruded
silicone gasket for a watertight seal. Door shall hinge and be self-retained via (1) stainless
steel cable.
Yoke
The luminaire yoke shall be formed from rigid steel bar 5/16” thick and 2.50” wide. Yoke is
designed for use with various mounting accessories and to be aimed at an optimum design
angle (determined by wattage +/- 5 degrees).
REFLECTOR
The luminaire reector module shall be of a high purity anodized specular aluminum to
provide an asymetrical distribution. Reector shall be backed by an aluminum extrusion for
stability and repeatability of distribution. The specular reector sheet shall be held in contour
to the extrusions by stainless steel extension springs. Reector shall include Sterner’s unique
lamp stabilizer to prevent lamp sag and to maximize lamp life and overall efciency.
INTERNAL REFLECTOR
Standard reector shall incorporate (2) internal louvers fastened to both ends to provide for
optimum shielding and glare control of the bare lamp. Optional Airport Louver ‘AV’ shall
incorporate a third louver to provide additional glare and spill light control required to meet
the stringent airport design criteria. Each louver shall be at black and/or lined with specular
aluminum to provide the appropriate asymetric distribution.
ELECTRICAL MODULE
Luminaire shall be cULus listed for use in wet locations and manufactured from UL
recognized electrical components. Electrical assembly is easily accessible through the
ballast box. Each high power factor ballast is capable of starting temperatures down to -20°F
(28.9°C) and shall be CWA. The socket shall be a mogul-based porcelain socket with a 4KV
rating (5KV for 1000HPS). Fixture shall be equipped with a watertight connector and 3’ of
16/3 STO-W cord.
LAMP
Luminaire shall accept the following lamps:
400PMH ED/BT37 750PMH pulse ED/BT37 400HPS E18
1000MH ED/BT37 1000PMH pulse ED/BT37 1000HPS E25
872 REMOTE MOUNTED BALLAST BOX
Ballast shall be housed in a cast aluminum housing with heat dissipating ns and supplied
with (2) watertight connectors. Ballast box shall have a cast aluminum cover and is secured
with (6) plated steel fasteners. 400PMH and 1000MH ballasts shall be capable of mounting at
a distance of 200’ (based on 10-gauge wire and 1% voltage drop), 750PMH AND 1000PMH
at a distance of 50’(includes long range starter). 400HPS ballast shall be capable of mounting
at a distance of 50’ and 1000HPS at 75’ (includes long range starter). The cast aluminum
alloy shall contain less than 2/10 of 1% copper for resistance to corrosion including marine
applications.
876 ATTACHED BALLAST BOX
Ballast shall be housed in an extruded aluminum housing with heat dissipating ns. Ballast
box shall have aluminum endplates, gasketed by an E.P.D.M. gasket and secured by (4)
stainless steel fasteners. Electrical components shall be mounted to an extruded ballast tray
that slides out for ease in servicing. Extruded box is to be attached separate from the luminaire
housing to reduce heat and wear, maximizing electrical component/lamp life.
FINISH
Finished parts are washed in a multistage phosphate processing system and nished with a
standard polyester urethane powder coat paint. Standard powder colors are dark bronze, black,
white, and natural aluminum. Contact factory for non-standard colors.
INFRANOR 872 / 876 WRITTEN SPECIFICATIONS
Fixture Dimensions
I N F R A N O R
In the interest of continuous product improvement, Sterner Lighting reserves the right to change specications without notice.
I N F R A N O R
SERIES - 872 / 876
I N F R A N O R
701 Millennium Blvd • Greenville, SC 29607 • TEL 864.678.1000 FAX 864.678.1417 • www.sternerlighting.com
In the interest of continuous product improvement, Sterner Lighting reserves the right to change specications without notice.
I N F R A N O R
872 / 876
TM Job Name:
Fixture Type:
Job Number:
Distributor:
Distributor P.O.:
F I X T U R E D I M E N S I O N S
I N F R A N O R 8 7 2 / 8 7 6 W R I T T E N S P E C I F I C A T I O N S
876
Side view shown
aimed 28°
6.00" Clearance hole for
3/4" mounting bolt.
Mounting bolt, by others.
0.56"
0.81"
25.94"
17.00"
20.00" 9.20"
872
Mounting bolt, by others.
3/4" mounting bolt.
Clearance hole for
9.20"
7.55"
1000W box
shown
Watertight cord connector
(2) supplied
14.31"
14.75"
(400W box: 6.5” x 15.0“ x 5.9”)
8.0"
top view
4.0"
20.00"
17.00"
22.50"
6.00"
0.56"
0.81"
(In-line & cluster mounts recommended for use with steel poles)
3.6 11.27.2 9.25.619.514.2876 8.9
7.3872 11.8 16.3 4.1 6.95.6 8.22.8
I10 C49C28 C39C29I40I30I20
EPA CHART (fixture & mounting combined)
MOUNTING
FIXTURE
HOUSING
The luminaire housing shall be mitre-formed construction from a single piece of
6063-T6 aluminum extrusion, with only a single seam located at the bottom of the
housing. The rear canopy shall be of aluminum sheet that is crimped into a specially
designed upper lip of the sidewall extrusion. This lip shall be lined with an Isocryl
gasket prior to the crimping process to form a fully sealed canopy without the use of
silicone or welds.
LENS & DOORFRAME
The luminaire lens shall be clear tempered glass, 0.188" thick, thermal and impact
resistant. Lens shall be set into a mitre formed extruded aluminum doorframe
which is secured by (6) self-retained stainless steel fasteners. Lens and doorframe are
gasketed by an extruded silicone gasket for a watertight seal. Door shall hinge and be
self-retained via (1) stainless steel cable.
YOKE
The luminaire yoke shall be formed from rigid steel bar 5/16" thick and 2.50" wide.
Yoke is designed for use with various mounting accessories and to be aimed at an
optimum design angle (determined by wattage +/- 5 degrees).
REFLECTOR
The luminaire reector module shall be of a high purity anodized specular
aluminum to provide an asymetrical distribution. Reector shall be backed by an
aluminum extrusion for stability and repeatability of distribution. The specular
reector sheet shall be held in contour to the extrusions by stainless steel extension
springs. Reector shall include Sterner’s patented lamp stabilizer to prevent lamp sag
and to maximize lamp life and overall eciency.
INTERNAL LOUVERS
Standard reector shall incorporate (2) internal louvers fastened to both ends to
provide for optimum shielding and glare control of the bare lamp. Optional Airport
Louver ‘AV’ shall incorporate a third louver to provide additional glare and spill light
control required to meet the stringent airport design criteria. Each louver shall be
at black and/or lined with specular aluminum to provide the appropriate
asymetric distribution.
ELECTRICAL MODULE
Luminaire shall be cULus listed for use in wet locations and manufactured from UL
recognized electrical components. Electrical assembly is easily accessible through the ballast
box. Each high power factor ballast is capable of starting temperatures down to -20°F (-
28.9°C) and shall be CWA. The socket shall be a mogul-based porcelain socket with a 4KV
rating (5KV for 1000HPS). Fixture shall be equipped with a watertight connector and 3' of
16/3 STO-W cord.
LAMP
Luminaire shall accept the following lamps:
400PMH ED/BT37 750PMH pulse ED/BT37 400HPS E18
1000MH ED/BT37 1000PMH pulse ED/BT37 1000HPS E25
872 REMOTE MOUNTED BALLAST BOX
Ballast shall be housed in a cast aluminum housing with heat dissipatingns and supplied
with (2) watertight connectors. Ballast box shall have a cast aluminum cover and is secured
with (6) plated steel fasteners. 400PMH and 1000MH ballasts shall be capable of mounting at
a distance of 200' (based on 10-gauge wire and 1% voltage drop), 750PMH AND 1000PMH
at a distance of 50'(includes long range starter). 400HPS ballast shall be capable of
mounting at a distance of 50' and 1000HPS at 75' (includes long range starter). The cast
aluminum alloy shall contain less than 2/10 of 1% copper for resistance to corrosion
including marine applications.
876 ATTACHED BALLAST BOX
Ballast shall be housed in an extruded aluminum housing with heat dissipating ns. Ballast
box shall have aluminum endplates, gasketed by an E.P.D.M. gasket and secured by (4)
stainless steel fasteners. Electrical components shall be mounted to an extruded ballast tray
that slides out for ease in servicing. Extruded box is to be attached separate from the
luminaire housing to reduce heat and wear, maximizing electrical component/lamp life.
FINISH
Finished parts are washed in a multistage phosphate processing system and nished with a
standard polyester urethane powder coat paint. Optional anodized nishes are available and
shall use an electrolytic process to oxidize and colorize the aluminum for a nish that is
extremely resistant aking, fading, and corrosive environments (some fabricated and
mounting hardware will be powder nish). Standard powder colors are dark bronze, black,
white, and natural aluminum. Standard anodized colors are bronze (light, medium, and
dark), black, and natural aluminum. Contact factory for non-standard colors.
FIXTURE WEIGHT: 90 LBS.
FIXTURE WEIGHT: 42 LBS.
REMOTE BOX WEIGHT: 50 LBS.
REMOTE BOX WEIGHT: 50 LBS
FIXTURE WEIGHT: 42 LBS
FIXTURE WEIGHT: 90 LBS
EPA CHART (fixture & mounting combined)
MOUNTING
FIXTURE 110 120 130 140 C28 C29 C39 C49
872 2.8 7.3 11.8 16.3 5.6 4.1 6.9 8.2
876 3.6 8.9 14.2 19.5 7.2 5.6 9.2 11.2
(In-line & cluster mounts recommended for use with steel poles)
AIMING CHART
LAMP BULB LOUVER IES MAX CP AIMING
400MH ED/
BT37
STD. TYPE-IV 26,475 63
1000MH ED/
BT37
STD.
AIRPORT
TYPE-IV 93,454
85,500
62
400HPS E18 STD.
AIRPORT
TYPE-IV 75,600
66,100
61
1000HPS E25 STD.
AIRPORT
TYPE-IV 183,700
179,700
60
11/14 1
STERNER LIGHTING • 701 Millennium Blvd • Greenville, SC 29607 • TEL 864.678.1000 FAX 864.678.1417 • www.sternerlighting.com
9. GENERAL OPTIONS
q (BK) Black
q (AL) Natural Aluminum
q (BZ) Dark Bronze
q (WH) White
Hubbell Lighting, Inc.
701 MILLENNIUM BOULEVARD GREENVILLE, SC 29607
TEL 864.678.1000 FAX 864.678.1417
1/09 www.sternerlighting.com
1. H O U S I N G 2. LAMP WATTAGE
3. BEAM PATTERN
4. VOLTAGE
5. BALLAST
7 . Q UANTIT Y / MOUNTI N G D E TAIL S (Note: First digit denotes xture qty. per assembly)
OPTIONS
STYLE
BALLAST
1
HOUSING
Item Sequence:
NUMBER:
ORDER
PATTERN
3
BEAM
WATTAGE
2
LAMP VOLTAGE
4 5
GENERAL
MODEL
6
MOUNTING
QUANTITY/
7
OPTIONS
SHIELD
8 9
FINISH
10
O R D E R I N G S E Q U E N C E
Anodized
Powder
7
7
7
7
7
AAL
DBZ
ABK
MBZ
LBZ
NS
BK
BZ
AL
WH
6
FL
SC
PRL
N
4
5
N
SG
TS
AV
3
3
2
2,3
2,3
2,3
2
2
2
2
WB
SF
I20
I30
I40
I10
PD
C28
C49
C39
C29
YK
C
1
4L
480
347
240
277
208
120
750PMH
1000PMH
400HPS
1000HPS
1000MH
400PMH872
876
(remote)
(attached)
('TS' Top shield nish is black unless otherwise specied.)
8 . SHIELD OPTI O N S 9. GENERAL O P T I O N S
10. FINI S H
Internal
3-louver
system
(AV) Airport Louver (SG)* Stone Guard
17.00"
20.25"
2.00"
(N) NOT REQUIRED
(TS)* Top Shield
4.31"
17.00"
20.00"
7) Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and
mounting options are powder finish.
6) 'PRL' Photocell Receptacle Luminaire not available with '872' remote version.
5) 'SG' Stone Guard not available for use with 'TS' Top Shield option.
NOTE: *'SG' Stone Guard
not available for use with
'TS' Top Shield option.
4) 'TS' Top Shield finish is black unless otherwise specified.
3) In-line brackets and 'PD' Base Pad require use of 'SF' Slip Fitter option per fixture.
2) First digit denotes fixture qty. per assembly.
NOTES: 1) Fixture designed to be aimed for optimal performance. See table on previous page for details.
NOTE: *In-line brackets and require
use of 'SF' Slip Fitter option per fixture.
Mounting bolt, by others.
3/4" mounting bolt.
Clearance hole for
Side view
Shown
aimed 28°
6.00"
Clearance hole for
3/4" mounting bolt.
Mounting bolt, by others.
9.20"
876
872 EPA: 3.60
FIXTURE WEIGHT: 90 LBS.
FIXTURE WEIGHT: 42 LBS.
EPA: 2.8 (fixture only)
REMOTE BOX WEIGHT: 50 LBS.
0.56"
0.81"
Watertight cord connector
(2) supplied
14.31"
14.75"
(400W box: 6.5” x 15.0“ x 5.9”)
8.0"
7.55"
1000W box shown
top view
4.0"
25.94"
17.00"
20.00"
20.00"
17.00"
22.50"
9.20"
6.00"
0.56"
0.88"
(4)
0.56"
06.00" dia.
bolt circle
2.38" O.D.
(2.00" sch. 40
0.25"
All components steel welded construction
steel pipe)
02.06" I.D.
6.00" 6.25"
3.44"
3.13"
Cast
tenzalloy
tter
pipe tenon x 4.00" long
(Min.)
To t 2.00" (2.38" O.D.)
Removable
(supplied)
connector
water-tite
installing
pipe plug for
Removable
mounting
side yoke
hole plug for
connector
Water-tite
1/2" set
screws Note: *'SF' Slip Fitter is required for use with 'PD' Base Pad option.
(PD) Base Pad(SF) Slip Fitter
(WB) Wall Bracket 3/4"
mounting
hardware
5.63"
splice inspection
cover
Removable
5.50"
8.00"
1.50"
hardware
3/4" mounting
horizontal sector
wall bracket and
Cast ductile iron
1.16"
Bolt
3/8" locking
bolt
1.81"
(Anchors supplied by others)
(Anchors supplied by others)
IN-LINE BRACKETS
(I20)* EPA 1.7
(2.38" O.D.
2.00" sch. 40
steel pipe)
44.50"
36.00"
4.00"
4.00"
4.00"
sq.
(I10)
Single
fixture In-line bracket pole top
tenon requirement
(3" sch. 40 steel pipe)
3.50"
6.00"
CLUSTER BRACKETS
GENERAL MOUNTING
(3.00" sch. 40 steel pipe)
requirement
pole top tenon
Cluster bracket
8.00"
3.50"
4.00"
(8) Set Screws 9.00"
6.00"
6.75"
15.75"
(C49) 4@90°(C39) 3@90°(C29) 2@90°(C28) 2@180°
(400MH) ED/BT37 (1000MH) ED/BT37
(750PMH) ED/BT37 (1000PMH) ED/BT37
(400HPS) E18 (1000HPS) E25
(120)
(208)
(240)
(277)
(347)
(480)
(4L) Asymetric Forward Throw
(C) Core & Coil
6. MODEL STYLE
(YK) Yoke
(I30)* EPA 3.4
80.50"
36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
(I40)* EPA 5.1
116.50"
36.00" 36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
Anodized
Powder
(WH)
Dark Bronze
(BZ)(BK)
Black
White
(NS) Non-Standard
(AL) Natural Aluminum (AAL)
Medium Bronze
(MBZ)(LBZ)
Light Bronze
Natural Aluminum
(DBZ) Dark Bronze
(NS) Non-Standard
(ABK) Black
Photocell Receptacle Luminaire(PRL)*
Fuse Luminaire(FL) Safety Cable(SC)
NOTE: *'PRL' Photocell Receptacle Luminaire not
available with '872' remote version.
Not Required(N)
NOTE: *Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and mounting options are powder finish.
Hubbell Lighting, Inc.
701 MILLENNIUM BOULEVARD GREENVILLE, SC 29607
TEL 864.678.1000 FAX 864.678.1417
1/09 www.sternerlighting.com
1. H O U S I N G 2. LAMP WATTAGE
3. BEAM PATTERN
4. VOLTAGE
5. BALLAST
7 . Q UANTIT Y / MOUNTI N G D E TAIL S (Note: First digit denotes xture qty. per assembly)
OPTIONS
STYLE
BALLAST
1
HOUSING
Item Sequence:
NUMBER:
ORDER
PATTERN
3
BEAM
WATTAGE
2
LAMP VOLTAGE
4 5
GENERAL
MODEL
6
MOUNTING
QUANTITY/
7
OPTIONS
SHIELD
8 9
FINISH
10
O R D E R I N G S E Q U E N C E
Anodized
Powder
7
7
7
7
7
AAL
DBZ
ABK
MBZ
LBZ
NS
BK
BZ
AL
WH
6
FL
SC
PRL
N
4
5
N
SG
TS
AV
3
3
2
2,3
2,3
2,3
2
2
2
2
WB
SF
I20
I30
I40
I10
PD
C28
C49
C39
C29
YK
C
1
4L
480
347
240
277
208
120
750PMH
1000PMH
400HPS
1000HPS
1000MH
400PMH872
876
(remote)
(attached)
('TS' Top shield nish is black unless otherwise specied.)
8 . SHIELD OPTI O N S 9. GENERAL O P T I O N S
10. FINI S H
Internal
3-louver
system
(AV) Airport Louver (SG)* Stone Guard
17.00"
20.25"
2.00"
(N) NOT REQUIRED
(TS)* Top Shield
4.31"
17.00"
20.00"
7) Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and
mounting options are powder finish.
6) 'PRL' Photocell Receptacle Luminaire not available with '872' remote version.
5) 'SG' Stone Guard not available for use with 'TS' Top Shield option.
NOTE: *'SG' Stone Guard
not available for use with
'TS' Top Shield option.
4) 'TS' Top Shield finish is black unless otherwise specified.
3) In-line brackets and 'PD' Base Pad require use of 'SF' Slip Fitter option per fixture.
2) First digit denotes fixture qty. per assembly.
NOTES: 1) Fixture designed to be aimed for optimal performance. See table on previous page for details.
NOTE: *In-line brackets and require
use of 'SF' Slip Fitter option per fixture.
Mounting bolt, by others.
3/4" mounting bolt.
Clearance hole for
Side view
Shown
aimed 28°
6.00"
Clearance hole for
3/4" mounting bolt.
Mounting bolt, by others.
9.20"
876
872 EPA: 3.60
FIXTURE WEIGHT: 90 LBS.
FIXTURE WEIGHT: 42 LBS.
EPA: 2.8 (fixture only)
REMOTE BOX WEIGHT: 50 LBS.
0.56"
0.81"
Watertight cord connector
(2) supplied
14.31"
14.75"
(400W box: 6.5” x 15.0“ x 5.9”)
8.0"
7.55"
1000W box shown
top view
4.0"
25.94"
17.00"
20.00"
20.00"
17.00"
22.50"
9.20"
6.00"
0.56"
0.88"
(4)
0.56"
06.00" dia.
bolt circle
2.38" O.D.
(2.00" sch. 40
0.25"
All components steel welded construction
steel pipe)
02.06" I.D.
6.00" 6.25"
3.44"
3.13"
Cast
tenzalloy
tter
pipe tenon x 4.00" long
(Min.)
To t 2.00" (2.38" O.D.)
Removable
(supplied)
connector
water-tite
installing
pipe plug for
Removable
mounting
side yoke
hole plug for
connector
Water-tite
1/2" set
screws Note: *'SF' Slip Fitter is required for use with 'PD' Base Pad option.
(PD) Base Pad(SF) Slip Fitter
(WB) Wall Bracket 3/4"
mounting
hardware
5.63"
splice inspection
cover
Removable
5.50"
8.00"
1.50"
hardware
3/4" mounting
horizontal sector
wall bracket and
Cast ductile iron
1.16"
Bolt
3/8" locking
bolt
1.81"
(Anchors supplied by others)
(Anchors supplied by others)
IN-LINE BRACKETS
(I20)* EPA 1.7
(2.38" O.D.
2.00" sch. 40
steel pipe)
44.50"
36.00"
4.00"
4.00"
4.00"
sq.
(I10)
Single
fixture In-line bracket pole top
tenon requirement
(3" sch. 40 steel pipe)
3.50"
6.00"
CLUSTER BRACKETS
GENERAL MOUNTING
(3.00" sch. 40 steel pipe)
requirement
pole top tenon
Cluster bracket
8.00"
3.50"
4.00"
(8) Set Screws 9.00"
6.00"
6.75"
15.75"
(C49) 4@90°(C39) 3@90°(C29) 2@90°(C28) 2@180°
(400MH) ED/BT37 (1000MH) ED/BT37
(750PMH) ED/BT37 (1000PMH) ED/BT37
(400HPS) E18 (1000HPS) E25
(120)
(208)
(240)
(277)
(347)
(480)
(4L) Asymetric Forward Throw
(C) Core & Coil
6. MODEL STYLE
(YK) Yoke
(I30)* EPA 3.4
80.50"
36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
(I40)* EPA 5.1
116.50"
36.00" 36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
Anodized
Powder
(WH)
Dark Bronze
(BZ)(BK)
Black
White
(NS) Non-Standard
(AL) Natural Aluminum (AAL)
Medium Bronze
(MBZ)(LBZ)
Light Bronze
Natural Aluminum
(DBZ) Dark Bronze
(NS) Non-Standard
(ABK) Black
Photocell Receptacle Luminaire(PRL)*
Fuse Luminaire(FL) Safety Cable(SC)
NOTE: *'PRL' Photocell Receptacle Luminaire not
available with '872' remote version.
Not Required(N)
NOTE: *Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and mounting options are powder finish.
Hubbell Lighting, Inc.
701 MILLENNIUM BOULEVARD GREENVILLE, SC 29607
TEL 864.678.1000 FAX 864.678.1417
1/09 www.sternerlighting.com
1. H O U S I N G 2. LAMP WATTAGE
3. BEAM PATTERN
4. VOLTAGE
5. BALLAST
7 . Q UANTIT Y / MOUNTI N G D E TAIL S (Note: First digit denotes xture qty. per assembly)
OPTIONS
STYLE
BALLAST
1
HOUSING
Item Sequence:
NUMBER:
ORDER
PATTERN
3
BEAM
WATTAGE
2
LAMP VOLTAGE
4 5
GENERAL
MODEL
6
MOUNTING
QUANTITY/
7
OPTIONS
SHIELD
8 9
FINISH
10
O R D E R I N G S E Q U E N C E
Anodized
Powder
7
7
7
7
7
AAL
DBZ
ABK
MBZ
LBZ
NS
BK
BZ
AL
WH
6
FL
SC
PRL
N
4
5
N
SG
TS
AV
3
3
2
2,3
2,3
2,3
2
2
2
2
WB
SF
I20
I30
I40
I10
PD
C28
C49
C39
C29
YK
C
1
4L
480
347
240
277
208
120
750PMH
1000PMH
400HPS
1000HPS
1000MH
400PMH872
876
(remote)
(attached)
('TS' Top shield nish is black unless otherwise specied.)
8 . SHIELD OPTI O N S 9. GENERAL O P T I O N S
10. FINI S H
Internal
3-louver
system
(AV) Airport Louver (SG)* Stone Guard
17.00"
20.25"
2.00"
(N) NOT REQUIRED
(TS)* Top Shield
4.31"
17.00"
20.00"
7) Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and
mounting options are powder finish.
6) 'PRL' Photocell Receptacle Luminaire not available with '872' remote version.
5) 'SG' Stone Guard not available for use with 'TS' Top Shield option.
NOTE: *'SG' Stone Guard
not available for use with
'TS' Top Shield option.
4) 'TS' Top Shield finish is black unless otherwise specified.
3) In-line brackets and 'PD' Base Pad require use of 'SF' Slip Fitter option per fixture.
2) First digit denotes fixture qty. per assembly.
NOTES: 1) Fixture designed to be aimed for optimal performance. See table on previous page for details.
NOTE: *In-line brackets and require
use of 'SF' Slip Fitter option per fixture.
Mounting bolt, by others.
3/4" mounting bolt.
Clearance hole for
Side view
Shown
aimed 28°
6.00"
Clearance hole for
3/4" mounting bolt.
Mounting bolt, by others.
9.20"
876
872 EPA: 3.60
FIXTURE WEIGHT: 90 LBS.
FIXTURE WEIGHT: 42 LBS.
EPA: 2.8 (fixture only)
REMOTE BOX WEIGHT: 50 LBS.
0.56"
0.81"
Watertight cord connector
(2) supplied
14.31"
14.75"
(400W box: 6.5” x 15.0“ x 5.9”)
8.0"
7.55"
1000W box shown
top view
4.0"
25.94"
17.00"
20.00"
20.00"
17.00"
22.50"
9.20"
6.00"
0.56"
0.88"
(4)
0.56"
06.00" dia.
bolt circle
2.38" O.D.
(2.00" sch. 40
0.25"
All components steel welded construction
steel pipe)
02.06" I.D.
6.00" 6.25"
3.44"
3.13"
Cast
tenzalloy
tter
pipe tenon x 4.00" long
(Min.)
To t 2.00" (2.38" O.D.)
Removable
(supplied)
connector
water-tite
installing
pipe plug for
Removable
mounting
side yoke
hole plug for
connector
Water-tite
1/2" set
screws Note: *'SF' Slip Fitter is required for use with 'PD' Base Pad option.
(PD) Base Pad(SF) Slip Fitter
(WB) Wall Bracket
3/4"
mounting
hardware
5.63"
splice inspection
cover
Removable
5.50"
8.00"
1.50"
hardware
3/4" mounting
horizontal sector
wall bracket and
Cast ductile iron
1.16"
Bolt
3/8" locking
bolt
1.81"
(Anchors supplied by others)
(Anchors supplied by others)
IN-LINE BRACKETS
(I20)* EPA 1.7
(2.38" O.D.
2.00" sch. 40
steel pipe)
44.50"
36.00"
4.00"
4.00"
4.00"
sq.
(I10)
Single
fixture In-line bracket pole top
tenon requirement
(3" sch. 40 steel pipe)
3.50"
6.00"
CLUSTER BRACKETS
GENERAL MOUNTING
(3.00" sch. 40 steel pipe)
requirement
pole top tenon
Cluster bracket
8.00"
3.50"
4.00"
(8) Set Screws 9.00"
6.00"
6.75"
15.75"
(C49) 4@90°(C39) 3@90°(C29) 2@90°(C28) 2@180°
(400MH) ED/BT37 (1000MH) ED/BT37
(750PMH) ED/BT37 (1000PMH) ED/BT37
(400HPS) E18 (1000HPS) E25
(120)
(208)
(240)
(277)
(347)
(480)
(4L) Asymetric Forward Throw
(C) Core & Coil
6. MODEL STYLE
(YK) Yoke
(I30)* EPA 3.4
80.50"
36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
(I40)* EPA 5.1
116.50"
36.00" 36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
Anodized
Powder
(WH)
Dark Bronze
(BZ)(BK)
Black
White
(NS) Non-Standard
(AL) Natural Aluminum (AAL)
Medium Bronze
(MBZ)(LBZ)
Light Bronze
Natural Aluminum
(DBZ) Dark Bronze
(NS) Non-Standard
(ABK) Black
Photocell Receptacle Luminaire(PRL)*
Fuse Luminaire(FL) Safety Cable(SC)
NOTE: *'PRL' Photocell Receptacle Luminaire not
available with '872' remote version.
Not Required(N)
NOTE: *Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and mounting options are powder finish.
Hubbell Lighting, Inc.
701 MILLENNIUM BOULEVARD GREENVILLE, SC 29607
TEL 864.678.1000 FAX 864.678.1417
1/09 www.sternerlighting.com
1. H O U S I N G 2. LAMP WATTAGE
3. BEAM PATTERN
4. VOLTAGE
5. BALLAST
7 . Q UANTIT Y / MOUNTI N G D E TAIL S (Note: First digit denotes xture qty. per assembly)
OPTIONS
STYLE
BALLAST
1
HOUSING
Item Sequence:
NUMBER:
ORDER
PATTERN
3
BEAM
WATTAGE
2
LAMP VOLTAGE
4 5
GENERAL
MODEL
6
MOUNTING
QUANTITY/
7
OPTIONS
SHIELD
8 9
FINISH
10
O R D E R I N G S E Q U E N C E
Anodized
Powder
7
7
7
7
7
AAL
DBZ
ABK
MBZ
LBZ
NS
BK
BZ
AL
WH
6
FL
SC
PRL
N
4
5
N
SG
TS
AV
3
3
2
2,3
2,3
2,3
2
2
2
2
WB
SF
I20
I30
I40
I10
PD
C28
C49
C39
C29
YK
C
1
4L
480
347
240
277
208
120
750PMH
1000PMH
400HPS
1000HPS
1000MH
400PMH872
876
(remote)
(attached)
('TS' Top shield nish is black unless otherwise specied.)
8 . SHIELD OPTI O N S 9. GENERAL O P T I O N S
10. FINI S H
Internal
3-louver
system
(AV) Airport Louver (SG)* Stone Guard
17.00"
20.25"
2.00"
(N) NOT REQUIRED
(TS)* Top Shield
4.31"
17.00"
20.00"
7) Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and
mounting options are powder finish.
6) 'PRL' Photocell Receptacle Luminaire not available with '872' remote version.
5) 'SG' Stone Guard not available for use with 'TS' Top Shield option.
NOTE: *'SG' Stone Guard
not available for use with
'TS' Top Shield option.
4) 'TS' Top Shield finish is black unless otherwise specified.
3) In-line brackets and 'PD' Base Pad require use of 'SF' Slip Fitter option per fixture.
2) First digit denotes fixture qty. per assembly.
NOTES: 1) Fixture designed to be aimed for optimal performance. See table on previous page for details.
NOTE: *In-line brackets and require
use of 'SF' Slip Fitter option per fixture.
Mounting bolt, by others.
3/4" mounting bolt.
Clearance hole for
Side view
Shown
aimed 28°
6.00"
Clearance hole for
3/4" mounting bolt.
Mounting bolt, by others.
9.20"
876
872 EPA: 3.60
FIXTURE WEIGHT: 90 LBS.
FIXTURE WEIGHT: 42 LBS.
EPA: 2.8 (fixture only)
REMOTE BOX WEIGHT: 50 LBS.
0.56"
0.81"
Watertight cord connector
(2) supplied
14.31"
14.75"
(400W box: 6.5” x 15.0“ x 5.9”)
8.0"
7.55"
1000W box shown
top view
4.0"
25.94"
17.00"
20.00"
20.00"
17.00"
22.50"
9.20"
6.00"
0.56"
0.88"
(4)
0.56"
06.00" dia.
bolt circle
2.38" O.D.
(2.00" sch. 40
0.25"
All components steel welded construction
steel pipe)
02.06" I.D.
6.00" 6.25"
3.44"
3.13"
Cast
tenzalloy
tter
pipe tenon x 4.00" long
(Min.)
To t 2.00" (2.38" O.D.)
Removable
(supplied)
connector
water-tite
installing
pipe plug for
Removable
mounting
side yoke
hole plug for
connector
Water-tite
1/2" set
screws Note: *'SF' Slip Fitter is required for use with 'PD' Base Pad option.
(PD) Base Pad(SF) Slip Fitter
(WB) Wall Bracket 3/4"
mounting
hardware
5.63"
splice inspection
cover
Removable
5.50"
8.00"
1.50"
hardware
3/4" mounting
horizontal sector
wall bracket and
Cast ductile iron
1.16"
Bolt
3/8" locking
bolt
1.81"
(Anchors supplied by others)
(Anchors supplied by others)
IN-LINE BRACKETS
(I20)* EPA 1.7
(2.38" O.D.
2.00" sch. 40
steel pipe)
44.50"
36.00"
4.00"
4.00"
4.00"
sq.
(I10)
Single
fixture In-line bracket pole top
tenon requirement
(3" sch. 40 steel pipe)
3.50"
6.00"
CLUSTER BRACKETS
GENERAL MOUNTING
(3.00" sch. 40 steel pipe)
requirement
pole top tenon
Cluster bracket
8.00"
3.50"
4.00"
(8) Set Screws 9.00"
6.00"
6.75"
15.75"
(C49) 4@90°(C39) 3@90°(C29) 2@90°(C28) 2@180°
(400MH) ED/BT37 (1000MH) ED/BT37
(750PMH) ED/BT37 (1000PMH) ED/BT37
(400HPS) E18 (1000HPS) E25
(120)
(208)
(240)
(277)
(347)
(480)
(4L) Asymetric Forward Throw
(C) Core & Coil
6. MODEL STYLE
(YK) Yoke
(I30)* EPA 3.4
80.50"
36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
(I40)* EPA 5.1
116.50"
36.00" 36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
Anodized
Powder
(WH)
Dark Bronze
(BZ)(BK)
Black
White
(NS) Non-Standard
(AL) Natural Aluminum (AAL)
Medium Bronze
(MBZ)(LBZ)
Light Bronze
Natural Aluminum
(DBZ) Dark Bronze
(NS) Non-Standard
(ABK) Black
Photocell Receptacle Luminaire(PRL)*
Fuse Luminaire(FL) Safety Cable(SC)
NOTE: *'PRL' Photocell Receptacle Luminaire not
available with '872' remote version.
Not Required(N)
NOTE: *Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and mounting options are powder finish.
Hubbell Lighting, Inc.
701 MILLENNIUM BOULEVARD GREENVILLE, SC 29607
TEL 864.678.1000 FAX 864.678.1417
1/09 www.sternerlighting.com
1. H O U S I N G 2. LAMP WATTAGE
3. BEAM PATTERN
4. VOLTAGE
5. BALLAST
7 . Q UANTIT Y / MOUNTI N G D E TAIL S (Note: First digit denotes xture qty. per assembly)
OPTIONS
STYLE
BALLAST
1
HOUSING
Item Sequence:
NUMBER:
ORDER
PATTERN
3
BEAM
WATTAGE
2
LAMP VOLTAGE
4 5
GENERAL
MODEL
6
MOUNTING
QUANTITY/
7
OPTIONS
SHIELD
8 9
FINISH
10
O R D E R I N G S E Q U E N C E
Anodized
Powder
7
7
7
7
7
AAL
DBZ
ABK
MBZ
LBZ
NS
BK
BZ
AL
WH
6
FL
SC
PRL
N
4
5
N
SG
TS
AV
3
3
2
2,3
2,3
2,3
2
2
2
2
WB
SF
I20
I30
I40
I10
PD
C28
C49
C39
C29
YK
C
1
4L
480
347
240
277
208
120
750PMH
1000PMH
400HPS
1000HPS
1000MH
400PMH872
876
(remote)
(attached)
('TS' Top shield nish is black unless otherwise specied.)
8 . SHIELD OPTI O N S 9. GENERAL O P T I O N S
10. FINI S H
Internal
3-louver
system
(AV) Airport Louver (SG)* Stone Guard
17.00"
20.25"
2.00"
(N) NOT REQUIRED
(TS)* Top Shield
4.31"
17.00"
20.00"
7) Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and
mounting options are powder finish.
6) 'PRL' Photocell Receptacle Luminaire not available with '872' remote version.
5) 'SG' Stone Guard not available for use with 'TS' Top Shield option.
NOTE: *'SG' Stone Guard
not available for use with
'TS' Top Shield option.
4) 'TS' Top Shield finish is black unless otherwise specified.
3) In-line brackets and 'PD' Base Pad require use of 'SF' Slip Fitter option per fixture.
2) First digit denotes fixture qty. per assembly.
NOTES: 1) Fixture designed to be aimed for optimal performance. See table on previous page for details.
NOTE: *In-line brackets and require
use of 'SF' Slip Fitter option per fixture.
Mounting bolt, by others.
3/4" mounting bolt.
Clearance hole for
Side view
Shown
aimed 28°
6.00"
Clearance hole for
3/4" mounting bolt.
Mounting bolt, by others.
9.20"
876
872 EPA: 3.60
FIXTURE WEIGHT: 90 LBS.
FIXTURE WEIGHT: 42 LBS.
EPA: 2.8 (fixture only)
REMOTE BOX WEIGHT: 50 LBS.
0.56"
0.81"
Watertight cord connector
(2) supplied
14.31"
14.75"
(400W box: 6.5” x 15.0“ x 5.9”)
8.0"
7.55"
1000W box shown
top view
4.0"
25.94"
17.00"
20.00"
20.00"
17.00"
22.50"
9.20"
6.00"
0.56"
0.88"
(4)
0.56"
06.00" dia.
bolt circle
2.38" O.D.
(2.00" sch. 40
0.25"
All components steel welded construction
steel pipe)
02.06" I.D.
6.00" 6.25"
3.44"
3.13"
Cast
tenzalloy
tter
pipe tenon x 4.00" long
(Min.)
To t 2.00" (2.38" O.D.)
Removable
(supplied)
connector
water-tite
installing
pipe plug for
Removable
mounting
side yoke
hole plug for
connector
Water-tite
1/2" set
screws Note: *'SF' Slip Fitter is required for use with 'PD' Base Pad option.
(PD) Base Pad
(SF) Slip Fitter
(WB) Wall Bracket
3/4"
mounting
hardware
5.63"
splice inspection
cover
Removable
5.50"
8.00"
1.50"
hardware
3/4" mounting
horizontal sector
wall bracket and
Cast ductile iron
1.16"
Bolt
3/8" locking
bolt
1.81"
(Anchors supplied by others)
(Anchors supplied by others)
IN-LINE BRACKETS
(I20)* EPA 1.7
(2.38" O.D.
2.00" sch. 40
steel pipe)
44.50"
36.00"
4.00"
4.00"
4.00"
sq.
(I10)
Single
fixture In-line bracket pole top
tenon requirement
(3" sch. 40 steel pipe)
3.50"
6.00"
CLUSTER BRACKETS
GENERAL MOUNTING
(3.00" sch. 40 steel pipe)
requirement
pole top tenon
Cluster bracket
8.00"
3.50"
4.00"
(8) Set Screws 9.00"
6.00"
6.75"
15.75"
(C49) 4@90°(C39) 3@90°(C29) 2@90°(C28) 2@180°
(400MH) ED/BT37 (1000MH) ED/BT37
(750PMH) ED/BT37 (1000PMH) ED/BT37
(400HPS) E18 (1000HPS) E25
(120)
(208)
(240)
(277)
(347)
(480)
(4L) Asymetric Forward Throw
(C) Core & Coil
6. MODEL STYLE
(YK) Yoke
(I30)* EPA 3.4
80.50"
36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
(I40)* EPA 5.1
116.50"
36.00" 36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
Anodized
Powder
(WH)
Dark Bronze
(BZ)(BK)
Black
White
(NS) Non-Standard
(AL) Natural Aluminum (AAL)
Medium Bronze
(MBZ)(LBZ)
Light Bronze
Natural Aluminum
(DBZ) Dark Bronze
(NS) Non-Standard
(ABK) Black
Photocell Receptacle Luminaire(PRL)*
Fuse Luminaire(FL) Safety Cable(SC)
NOTE: *'PRL' Photocell Receptacle Luminaire not
available with '872' remote version.
Not Required(N)
NOTE: *Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and mounting options are powder finish.
Hubbell Lighting, Inc.
701 MILLENNIUM BOULEVARD GREENVILLE, SC 29607
TEL 864.678.1000 FAX 864.678.1417
1/09 www.sternerlighting.com
1. H O U S I N G 2. LAMP WATTAGE
3. BEAM PATTERN
4. VOLTAGE
5. BALLAST
7 . Q UANTIT Y / MOUNTI N G D E TAIL S (Note: First digit denotes xture qty. per assembly)
OPTIONS
STYLE
BALLAST
1
HOUSING
Item Sequence:
NUMBER:
ORDER
PATTERN
3
BEAM
WATTAGE
2
LAMP VOLTAGE
4 5
GENERAL
MODEL
6
MOUNTING
QUANTITY/
7
OPTIONS
SHIELD
8 9
FINISH
10
O R D E R I N G S E Q U E N C E
Anodized
Powder
7
7
7
7
7
AAL
DBZ
ABK
MBZ
LBZ
NS
BK
BZ
AL
WH
6
FL
SC
PRL
N
4
5
N
SG
TS
AV
3
3
2
2,3
2,3
2,3
2
2
2
2
WB
SF
I20
I30
I40
I10
PD
C28
C49
C39
C29
YK
C
1
4L
480
347
240
277
208
120
750PMH
1000PMH
400HPS
1000HPS
1000MH
400PMH872
876
(remote)
(attached)
('TS' Top shield nish is black unless otherwise specied.)
8 . SHIELD OPTI O N S 9. GENERAL O P T I O N S
10. FINI S H
Internal
3-louver
system
(AV) Airport Louver (SG)* Stone Guard
17.00"
20.25"
2.00"
(N) NOT REQUIRED
(TS)* Top Shield
4.31"
17.00"
20.00"
7) Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and
mounting options are powder finish.
6) 'PRL' Photocell Receptacle Luminaire not available with '872' remote version.
5) 'SG' Stone Guard not available for use with 'TS' Top Shield option.
NOTE: *'SG' Stone Guard
not available for use with
'TS' Top Shield option.
4) 'TS' Top Shield finish is black unless otherwise specified.
3) In-line brackets and 'PD' Base Pad require use of 'SF' Slip Fitter option per fixture.
2) First digit denotes fixture qty. per assembly.
NOTES: 1) Fixture designed to be aimed for optimal performance. See table on previous page for details.
NOTE: *In-line brackets and require
use of 'SF' Slip Fitter option per fixture.
Mounting bolt, by others.
3/4" mounting bolt.
Clearance hole for
Side view
Shown
aimed 28°
6.00"
Clearance hole for
3/4" mounting bolt.
Mounting bolt, by others.
9.20"
876
872 EPA: 3.60
FIXTURE WEIGHT: 90 LBS.
FIXTURE WEIGHT: 42 LBS.
EPA: 2.8 (fixture only)
REMOTE BOX WEIGHT: 50 LBS.
0.56"
0.81"
Watertight cord connector
(2) supplied
14.31"
14.75"
(400W box: 6.5” x 15.0“ x 5.9”)
8.0"
7.55"
1000W box shown
top view
4.0"
25.94"
17.00"
20.00"
20.00"
17.00"
22.50"
9.20"
6.00"
0.56"
0.88"
(4)
0.56"
06.00" dia.
bolt circle
2.38" O.D.
(2.00" sch. 40
0.25"
All components steel welded construction
steel pipe)
02.06" I.D.
6.00" 6.25"
3.44"
3.13"
Cast
tenzalloy
tter
pipe tenon x 4.00" long
(Min.)
To t 2.00" (2.38" O.D.)
Removable
(supplied)
connector
water-tite
installing
pipe plug for
Removable
mounting
side yoke
hole plug for
connector
Water-tite
1/2" set
screws Note: *'SF' Slip Fitter is required for use with 'PD' Base Pad option.
(PD) Base Pad
(SF) Slip Fitter
(WB) Wall Bracket 3/4"
mounting
hardware
5.63"
splice inspection
cover
Removable
5.50"
8.00"
1.50"
hardware
3/4" mounting
horizontal sector
wall bracket and
Cast ductile iron
1.16"
Bolt
3/8" locking
bolt
1.81"
(Anchors supplied by others)
(Anchors supplied by others)
IN-LINE BRACKETS
(I20)* EPA 1.7
(2.38" O.D.
2.00" sch. 40
steel pipe)
44.50"
36.00"
4.00"
4.00"
4.00"
sq.
(I10)
Single
fixture In-line bracket pole top
tenon requirement
(3" sch. 40 steel pipe)
3.50"
6.00"
CLUSTER BRACKETS
GENERAL MOUNTING
(3.00" sch. 40 steel pipe)
requirement
pole top tenon
Cluster bracket
8.00"
3.50"
4.00"
(8) Set Screws 9.00"
6.00"
6.75"
15.75"
(C49) 4@90°(C39) 3@90°(C29) 2@90°(C28) 2@180°
(400MH) ED/BT37 (1000MH) ED/BT37
(750PMH) ED/BT37 (1000PMH) ED/BT37
(400HPS) E18 (1000HPS) E25
(120)
(208)
(240)
(277)
(347)
(480)
(4L) Asymetric Forward Throw
(C) Core & Coil
6. MODEL STYLE
(YK) Yoke
(I30)* EPA 3.4
80.50"
36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
(I40)* EPA 5.1
116.50"
36.00" 36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
Anodized
Powder
(WH)
Dark Bronze
(BZ)(BK)
Black
White
(NS) Non-Standard
(AL) Natural Aluminum (AAL)
Medium Bronze
(MBZ)(LBZ)
Light Bronze
Natural Aluminum
(DBZ) Dark Bronze
(NS) Non-Standard
(ABK) Black
Photocell Receptacle Luminaire(PRL)*
Fuse Luminaire(FL) Safety Cable(SC)
NOTE: *'PRL' Photocell Receptacle Luminaire not
available with '872' remote version.
Not Required(N)
NOTE: *Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and mounting options are powder finish.
7. QUANTITY / MOUNTING DETAILS (Note: First digit denotes fixture qty. per assembly)
8. SHIELD OPTIONS (‘TS’ Top shield finish is black unless otherwise specified.)
ordering sequence
1. HOUSING 2. LAMP WATTAGE
3. BEAM PATTERN
4. VOLTAGE
5. BALLAST
6. MODEL STYLE
ORDER
NUMBER:
Item Sequence: 1 2 3 4 5 6 7 8 9 10
HOUSING LAMP
WATTAGE
872:
400PMH
1000MH
876:
750PMH
1000PMH
400HPS
1000HPS
BEAM
PATTERN
4L1
VOLTAGE
120
208
240
277
347
480
I102
I202,3
I302,3
I402,3
N
C282
C292
C392
C492
PD3
SF3
WB
AV
TS4,5
SG5
N
C
BALLAST MODEL
STYLE QUANTITY
MOUNTING SHIELD
OPTIONS
FL
SC
PRL6
N
BK
BZ
WH
AL
GENERAL
OPTIONS FINISH
872
(remote)
876
(attached)
YK
872
IN-LINE BRACKETS
CLOSE CLUSTER BRACKETS
GENERAL MOUNTING
q (I10) q (I20)* EPA 1.7 q (I30)* EPA 3.4
q (C28)* 2@180º
q (WB) Wall Bracket
q (AV) Airport Louver q (TS)* Top Shield
q (N) NOT REQUIRED
q (SG)* Stone Guard q (SC) Safety Cableq (FL) Fuse Luminaire
q (PRL)* Photocell Receptacle Luminaire
NOTE: *’PRL’ Photocell Receptacle Luminaire not
available with ‘872’ remote version.
q (SF) Slip Fitter q (PD) Base Pod q (N) Not
Required
q (N) Not Required
q (C29)* 2@90ºq (C39)* 3@90ºq (C49)* 4@90º
q (I40)* EPA 5.1 (wind load rating
is for Bracket only)
q (1000MH) ED/BT37(872)
q (750PMH) ED/BT37(876)
q (400HPS) ED18
q (120)
q (208)
q (240)
q (277)
q (347)
q (480)
q (4L) Asymetric Forward Throw
q (C) Core & Coil
q (YK) Yoke
q (400PMH) ED/BT37
q (1000PMH) ED/BT37
q (1000HPS) ED18
876 (ATTACHED) FIXTURE WEIGHT: 90 LBS.
EPA: 3.60
REMOTE BOX WEIGHT: 50 LBS.
FIXTURE WEIGHT: 27 LBS.
EPA: 2.50 (fixture only)
10. FINISH
Powder
Hubbell Lighting, Inc.
701 MILLENNIUM BOULEVARD GREENVILLE, SC 29607
TEL 864.678.1000 FAX 864.678.1417
1/09 www.sternerlighting.com
1. H O U S I N G 2. LAMP WATTAGE
3. BEAM PATTERN
4. VOLTAGE
5. BALLAST
7 . Q UANTIT Y / MOUNTI N G D E TAIL S
(Note: First digit denotes xture qty. per assembly)
OPTIONS
STYLE
BALLAST
1
HOUSING
Item Sequence:
NUMBER:
ORDER
PATTERN
3
BEAM
WATTAGE
2
LAMP VOLTAGE
4 5
GENERAL
MODEL
6
MOUNTING
QUANTITY/
7
OPTIONS
SHIELD
8 9
FINISH
10
O R D E R I N G S E Q U E N C E
Anodized
Powder
7
7
7
7
7
AAL
DBZ
ABK
MBZ
LBZ
NS
BK
BZ
AL
WH
6
FL
SC
PRL
N
4
5
N
SG
TS
AV
3
3
2
2,3
2,3
2,3
2
2
2
2
WB
SF
I20
I30
I40
I10
PD
C28
C49
C39
C29
YK
C
1
4L
480
347
240
277
208
120
750PMH
1000PMH
400HPS
1000HPS
1000MH
400PMH872
876
(remote)
(attached)
('TS' Top shield nish is black unless otherwise specied.)
8 . SHIELD OPTI O N S 9. GENERAL O P T I O N S
10. FINI S H
Internal
3-louver
system
(AV) Airport Louver (SG)* Stone Guard
17.00"
20.25"
2.00"
(N) NOT REQUIRED
(TS)* Top Shield
4.31"
17.00"
20.00"
7) Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and
mounting options are powder finish.
6) 'PRL' Photocell Receptacle Luminaire not available with '872' remote version.
5) 'SG' Stone Guard not available for use with 'TS' Top Shield option.
NOTE: *'SG' Stone Guard
not available for use with
'TS' Top Shield option.
4) 'TS' Top Shield finish is black unless otherwise specified.
3) In-line brackets and 'PD' Base Pad require use of 'SF' Slip Fitter option per fixture.
2) First digit denotes fixture qty. per assembly.
NOTES: 1) Fixture designed to be aimed for optimal performance. See table on previous page for details.
NOTE: *In-line brackets and require
use of 'SF' Slip Fitter option per fixture.
Mounting bolt, by others.
3/4" mounting bolt.
Clearance hole for
Side view
Shown
aimed 28°
6.00"
Clearance hole for
3/4" mounting bolt.
Mounting bolt, by others.
9.20"
876
872 EPA: 3.60
FIXTURE WEIGHT: 90 LBS.
FIXTURE WEIGHT: 42 LBS.
EPA: 2.8 (fixture only)
REMOTE BOX WEIGHT: 50 LBS.
0.56"
0.81"
Watertight cord connector
(2) supplied
14.31"
14.75"
(400W box: 6.5” x 15.0“ x 5.9”)
8.0"
7.55"
1000W box shown
top view
4.0"
25.94"
17.00"
20.00"
20.00"
17.00"
22.50"
9.20"
6.00"
0.56"
0.88"
(4)
0.56"
06.00" dia.
bolt circle
2.38" O.D.
(2.00" sch. 40
0.25"
All components steel welded construction
steel pipe)
02.06" I.D.
6.00" 6.25"
3.44"
3.13"
Cast
tenzalloy
tter
pipe tenon x 4.00" long
(Min.)
To t 2.00" (2.38" O.D.)
Removable
(supplied)
connector
water-tite
installing
pipe plug for
Removable
mounting
side yoke
hole plug for
connector
Water-tite
1/2" set
screws
Note: *'SF' Slip Fitter is required for use with 'PD' Base Pad option.
(PD)
Base Pad(SF)
Slip Fitter
(WB)
Wall Bracket 3/4"
mounting
hardware
5.63"
splice inspection
cover
Removable
5.50"
8.00"
1.50"
hardware
3/4" mounting
horizontal sector
wall bracket and
Cast ductile iron
1.16"
Bolt
3/8" locking
bolt
1.81"
(Anchors supplied by others)
(Anchors supplied by others)
IN-LINE BRACKETS
(I20)*
EPA 1.7
(2.38" O.D.
2.00" sch. 40
steel pipe)
44.50"
36.00"
4.00"
4.00"
4.00"
sq.
(I10)
Single
fixture In-line bracket pole top
tenon requirement
(3" sch. 40 steel pipe)
3.50"
6.00"
CLUSTER BRACKETS
GENERAL MOUNTING
(3.00" sch. 40 steel pipe)
requirement
pole top tenon
Cluster bracket
8.00"
3.50"
4.00"
(8) Set Screws 9.00"
6.00"
6.75"
15.75"
(C49) 4@90°(C39) 3@90°(C29) 2@90°(C28) 2@180°
(400MH)
ED/BT37
(1000MH)
ED/BT37
(750PMH)
ED/BT37
(1000PMH)
ED/BT37
(400HPS)
E18
(1000HPS)
E25
(120)
(208)
(240)
(277)
(347)
(480)
(4L) Asymetric Forward Throw
(C) Core & Coil
6. MODEL STYLE
(YK) Yoke
(I30)* EPA 3.4
80.50"
36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
(I40)* EPA 5.1
116.50"
36.00" 36.00" 36.00"
4.00"
4.00"
4.00"
sq.
(2.38" O.D.
2.00" sch. 40 steel pipe)
Anodized
Powder
(WH)
Dark Bronze
(BZ)(BK)
Black
White
(NS) Non-Standard
(AL) Natural Aluminum (AAL)
Medium Bronze
(MBZ)(LBZ)
Light Bronze
Natural Aluminum
(DBZ) Dark Bronze
(NS) Non-Standard
(ABK) Black
Photocell Receptacle Luminaire(PRL)*
Fuse Luminaire(FL) Safety Cable(SC)
NOTE: *'PRL' Photocell Receptacle Luminaire not
available with '872' remote version.
Not Required(N)
NOTE: *Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and mounting options are powder finish.
Notes: 1) Fixture designed to be aimed for optimal performance – (See Aiming Chart on page 1)
2) First digit denotes fixture qty. per assembly.
3) In-line brackets and ‘PD’ Base Pad require use of ‘SF’ Slip Fitter option per fixture.
4) ‘TS’ top shield finish is black unless otherwise specified.
5) ‘SG’ Stone Guard not available for use with ‘TS’ Top Shield option.
6) ‘PRL’ Photocell Receptacle Luminaire not available with ‘872’ remote version.
7) Extruded parts (housing, doorframe, & ballast box) are anodized. Fabricated yoke parts and
mounting options are powder finish.
Powder
** Please supply chip to match or specify color for any ‘NS’ non-standard finish
INFRANOR 872 / 876
11/14 2

Navigation menu