902688 Instructions

: Pdf 902688 Instructions 902688_Instructions product s

Open the PDF directly: View PDF .
Page Count: 4

Download
Open PDF In Browser	View PDF

Installation/Operating Instructions

Galaxy LEGACY DE:
902688 - 1000 Watt 120 – 240 Volt Ballast

READ THESE INSTRUCTIONS BEFORE FIRING UP YOUR BALLAST
KEEP ORIGINAL PACKAGING— all returns need to be in the original packaging
in order to avoid product damage during shipping. Any damage to products not in
their original packaging will not be covered under warranty.
SAFETY FIRST! Failure to observe the following safety warnings may result in
serious injury. In addition, failure to observe these safety warnings will result in a
waiver of all liabilities and will void all warranties.
WARNING
	 	If the exterior of the lamp is damaged, replace lamp immediately.
	 	When re-lamping, make sure lamp has time to cool before touching.
	 	Make sure reflector sockets are in the closed position—properly securing
the lamp.
	 	Make sure power cord and lamp cord are connected properly.
	 	Disconnect power before re-lamping.
		DO NOT hang by power or lamp cord.
	 	DO NOT make contact with the interior of the socket while power is on.
	 	DO NOT operate light systems in wet locations.
	 		
DO NOT plug system into supply voltage other than what is designated on ballast.
	 		
DO NOT attempt to rewire or reconfigure your system, it will void warranty and
could cause serious safety hazards (i.e. power cord, lamp cord, lamp socket or ballast).
	 	Keep away from children.

SAFETY FIRST!
			
DO NOT alter or modify this unit in any way. It may cause bodily injury or
death as this is a high power electrical device.
		DO NOT submerse in water or splash water on the unit.
		DO NOT plug or unplug the lamp cord while the ballast is energized.
These high performance, high frequency Electronic Ballasts are extremely efficient.
They have a high power factor and high luminous efficacy. It’s stable performance
creates constant power output even when power fluctuates (power surge). Short circuit
protection technology prevents damage to the lamp and other ballasts connected
to the same circuit.
1. INSTALLATION PROCEDURE
	 		
DO NOT alter or modify the electronic ballast in any way.
Not only may it damage the unit, it will void the warranty.
	 		
Lamp power rating must match electronic ballast power rating.
CONNECT APPROPRIATE
AC POWER PLUG HERE
Includes Convertible
Smart Volt® 120V/240V
power cord.

OUTPUT TO DE LAMP
Connect “Sun System®”
lamp cord with male plug to
female receptacle on ballast

The 902688 Galaxy Legacy DE 1000 Watt 120 – 240V ballast includes our exclusive
Convertible Smart Volt® 120V/240V Power Cord. The Galaxy Legacy DE is a “smart”
ballast that will operate on either 120, 208 or 240 volt power by simply plugging in
the appropriate Smart Volt power cord adapter.
2. SPECIFICATIONS
		
902688 is 120, 208 or 240 Volt,
	
	
Power source frequency: 50/60Hz
	
		
Power Factor (cosø): > 0.99
	
	 	
Ambient Temp: 50˚F to 120˚F
	

	
Crest Factor: < 1.5
	 	
Acoustic Resonance: none
		
Total Harmonic Distortion:
	
(THD): < 10.0%

3. NOTES
	 		
The Galaxy Legacy DE Electronic Ballast is designed to operate properly rated
double-ended lamps.
	 		
This unit offers short-circuit and power fluctuation.

240V WIRING - VERY IMPORTANT! All digital ballasts may malfunction if the
240V circuit has a neutral. The input for the ballast is 2 HOT WIRES and 1 GROUND
WIRE. If you are using a light controller ONLY bring a ground wire and two hot leads
from your electrical panels.
HOT RESTRIKE - It is VERY IMPORTANT that the lamp is given adequate time
to cool down before it is reignited. You should allow a hot lamp to cool for 20-30
minutes before you try to restrike it. Hot restrikes cause permanent lamp failure and
lumen output degradation. Additionally, the lamp should never be turned off before
the lamp reaches full intensity.

LAMP REPLACEMENT - Be sure to disconnect the power source before
changing lamps. Always use the specified wattage lamp. (A 400W lamp should
not be used in the 600W setting).
MOUNTING LOCATION - DO NOT install ballasts in areas of high heat, such
as an attic or a closed closet. DO NOT mount the ballast to the reflector or blow
exhaust air over them. DO NOT stack ballasts on top of each other. DO NOT allow
contact with water. Mount units at least six inches apart. If a unit has any leaking
resin, please relocate to a cooler area or place a fan near the ballasts.
TIMER BOX - If you are connecting a 240V ballast to a timer box, please make
sure that it cuts off both legs when timer is switched off. If you continue to supply
120V to your ballast when the timer is switched off, it may damage your ballast.
HPS/MH - The ballasts operate both metal halide and high pressure sodium lamps.
They will not light mercury vapor lamps.
LAMP RECOMMENDATIONS - The ballasts are designed to provide superior
performance with several lamps manufactured to American specifications. There
are several brands of lamps available for the U.S. market that were made according
to European specifications. We do not recommend using these types of lamps,
since they will provide inconsistent performance with your ballast.

TROUBLESHOOTING GUIDE
Follow the troubleshooting tips below. If troubleshooting techniques fail, bring
ballast back to your place of purchase to request warranty service.
POSSIBLE CAUSES CORRECTIVE MAINTENANCE
LAMP LOOSE
IN SOCKETS
INCORRECT
VOLTAGE
DEFECTIVE
OR IMPROPER
WIRING

Make sure that the lamp is fully inserted into the sockets and that the
sockets are in the closed position.
Make sure you are using the correct input voltage with ballast. If using
incorrect voltage, disconnect the ballast from the power source immediately.
Examine wiring to ensure it agrees with wiring diagrams on ballast label.
Check connections to see that they are secure. If wiring a 240V ballast,
DO NOT use a neutral. The correct wiring is two hot wires and a ground.

POOR ELECTRICAL Check wiring and lamp contact with socket. Make sure the lamp cord is
CONNECTIONS
firmly seated in output receptacle.
INCORRECT
LAMP
LAMP
DAMAGE

Verify that you are using a 1000W double ended lamp. Lamps manufactured
according to European or Asian specifications will not provide consistent
performance.
Investigate possibility of outer bulb damage.
Look for broken tubes or loose metal parts. Replace lamp.

See back page for important FCC and warranty information

RETURNING UNITS Please contact your retail store for returns.
WARRANTY This unit, when properly used will provide you with years of service.
It is covered under a 3 year warranty. This warranty will be voided if the unit is
misused, abused or altered. Warranty repair or replacement will be at the sole
discretion of the manufacturer. Defective units need to be returned to the place
of purchase with proof of purchase/receipt.
This warranty is expressly in lieu of all other warranties, expressed or implied,
including the warranties of merchantability and fitness for use and of all other
obligations or liabilities on the part of the seller. This warranty shall not apply
to this product or any part thereof which has been damaged by accident, abuse,
misuse, modification, negligence, alteration or misapplication. Manufacturer
makes no warranty whatsoever in respect to accessories or parts not supplied by
manufacturer. This warranty shall apply only to the United States, including Alaska,
Hawaii and territories of the United States and Canada. This warranty does not
cover labor materials, travel time, equipment, etc. to de-install any lighting fixtures
or other equipment.
Part 18 compliance

This device complies with Part 18 of the FCC Rules.

Advisory statement

This product may cause interference to radio equipment and
should not be installed near maritime safety communications
equipment or other critical navigation or communication
equipment operating between 0.45-30 MHz.

The interference potential
of the device or system

The interference potential of the device or system is the
operating frequency; 110 kHz.

Maintenance of the system

Unplug the unit, wait 30 seconds, and plug the unit back in.

Simple measures that can be taken Move the unit away from any radio device.
by the user to correct interference
This product contains delicate electronic components. This means that if it is placed
near an object that transmits radio signals, it could cause interference. This could
be, for example, mobile telephones, walkie talkies, CB radios, remote controls and
microwaves. If interference occurs, move such objects away from the appliance.
Galaxy Legacy DE Select-A-Watt 600/750/875/1000/Turbo Charge 120 – 240 Volt:
FCC#: 2AEHV902688



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Language                        : en-US
XMP Toolkit                     : Adobe XMP Core 5.6-c123 79.158978, 2016/02/13-01:11:19
Creator Tool                    : Adobe InDesign CC 2015 (Macintosh)
Create Date                     : 2017:03:28 11:09-07:00
Metadata Date                   : 2017:03:28 11:09-07:00
Modify Date                     : 2017:03:28 11:09-07:00
Instance ID                     : uuid:d6bd5260-0079-bb49-8581-a0eea212f027
Original Document ID            : xmp.did:cd17f253-efea-4869-929e-e975e08b744e
Document ID                     : xmp.id:2f0c2298-c332-4263-8ce1-a74e5edcdb68
Rendition Class                 : proof:pdf
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Macintosh)
History Changed                 : /
History When                    : 2017:03:28 11:09-07:00
Derived From Instance ID        : xmp.iid:cd17f253-efea-4869-929e-e975e08b744e
Derived From Document ID        : xmp.did:cd17f253-efea-4869-929e-e975e08b744e
Derived From Original Document ID: xmp.did:cd17f253-efea-4869-929e-e975e08b744e
Derived From Rendition Class    : default
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 4
Creator                         : Adobe InDesign CC 2015 (Macintosh)

EXIF Metadata provided by EXIF.tools