AMD NVMe/SATA RAID Quick Start Guide For Windows® Operating Systems Ryzen NVMe 1.02
User Manual: Pdf AMD Ryzen NVMe RAID quick-start-guide 1.02
Open the PDF directly: View PDF 
.
Page Count: 18
| Download | |
| Open PDF In Browser | View PDF |
AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Publication # 56268 Revision: 1.02 Issue Date: April 2018 Advanced Micro Devices © 2018 Advanced Micro Devices, Inc. All rights reserved. The information contained herein is for informational purposes only, and is subject to change without notice. While every precaution has been taken in the preparation of this document, it may contain technical inaccuracies, omissions and typographical errors, and AMD is under no obligation to update or otherwise correct this information. Advanced Micro Devices, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this document, and assumes no liability of any kind, including the implied warranties of noninfringement, merchantability or fitness for particular purposes, with respect to the operation or use of AMD hardware, software or other products described herein. No license, including implied or arising by estoppel, to any intellectual property rights is granted by this document. Terms and limitations applicable to the purchase or use of AMD’s products are as set forth in a signed agreement between the parties or in AMD's Standard Terms and Conditions of Sale. Trademarks AMD, the AMD Arrow logo, AMD Ryzen, Threadripper, and combinations thereof are trademarks of Advanced Micro Devices, Inc. Other product names used in this publication are for identification purposes only and may be trademarks of their respective companies. Reverse engineering or disassembly is prohibited. Microsoft and Windows are registered trademarks of Microsoft Corporation. Dolby Laboratories, Inc. Manufactured under license from Dolby Laboratories. Rovi Corporation This device is protected by U.S. patents and other intellectual property rights. The use of Rovi Corporation's copy protection technology in the device must be authorized by Rovi Corporation and is intended for home and other limited pay-per-view uses only, unless otherwise authorized in writing by Rovi Corporation. USE OF THIS PRODUCT IN ANY MANNER THAT COMPLIES WITH THE MPEG ACTUAL OR DE FACTO VIDEO AND/OR AUDIO STANDARDS IS EXPRESSLY PROHIBITED WITHOUT ALL NECESSARY LICENSES UNDER APPLICABLE PATENTS. SUCH LICENSES MAY BE ACQUIRED FROM VARIOUS THIRD PARTIES INCLUDING, BUT NOT LIMITED TO, IN THE MPEG PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, L.L.C., 6312 S. FIDDLERS GREEN CIRCLE, SUITE 400E, GREENWOOD VILLAGE, COLORADO 80111. 56268 Rev. 1.02 April 2018 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Contents Revision History .............................................................................................................................5 Chapter 1 General Information ..............................................................................................6 1.1 Purpose.............................................................................................................................6 1.2 System Requirements ......................................................................................................6 1.3 Generic System Setup ......................................................................................................7 Chapter 2 2.1 BOOTABLE ARRAYS .........................................................................................8 Copy AMD-RAID Drivers to a Removable Storage Medium: Windows® ......................8 Chapter 3 Pre-Installation Steps .............................................................................................9 3.1 Platform BIOS Settings - Enable RAID for the AMD SP3-Series Chipsets ...................9 3.2 Platform BIOS Settings – Enable RAID for the AMD Socket AM4-Compatible Processors ......................................................................................................................10 Chapter 4 Create the Bootable Virtual Disk .......................................................................12 4.1 RAIDXpert2 Configuration Utility (HII Mode) For the AMD Ryzen™ Threadripper™ Processor ........................................................................................................................12 4.2 RAIDXpert2 Configuration Utility (HII Mode) For the AMD Ryzen™ Desktop Processor ........................................................................................................................13 4.3 UEFI Mode ....................................................................................................................14 Chapter 5 5.1 Windows®: Install AMD-RAID UEFI Drivers during Windows® OS Installation ........15 Chapter 6 6.1 Install AMD-RAID Drivers .................................................................................15 Install the AMD-RAIDXpert2 Management Suite and Web GUI ..................17 Windows® – AMD-RAIDXpert2 Management Suite ....................................................17 6.1.1 Windows® – AMD-RAIDXpert2 Management Suite ...........................................17 6.1.2 Windows® – AMD RAIDXpert2 Management Suite Installation (Manually) ......17 List of Tables Table 1. System Requirements ........................................................................................................6 Table 2. Information about Supported Configuration by Installer ...................................................7 Contents 3 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems 4 List of Tables 56268 Rev. 1.02 April 2018 56268 Rev. 1.02 April 2018 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Revision History Date Revision Description April 2018 1.02 First public release. March 2018 1.01 2nd NDA release. Updated Supported Configuration and minor edits. February 2018 1.00 Initial NDA release. Revision History 5 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Chapter 1 1.1 56268 Rev. 1.02 April 2018 General Information Purpose This Quick Start Guide is designed to assist with system setup in RAID Mode, by performing these general procedures: • Copy AMD RAID device drivers to removable storage media for the following operating systems: o Microsoft ® Windows 10 x64 • Load AMD RAID device drivers on a system at the time during Windows operating system installation. • Install the AMD-RAIDXpert2 (Web GUI) for RAID array management 1.2 System Requirements Table 1. System Requirements Component Requirements Memory (RAM) Minimum: 8 GB Recommended: 32 GB Hard Disk One to Fourteen SATA HDD’s, SATA SSD’s or NVMe Max number of NVMe devices 10 Max Controller Count 11 (Two controllers with Device ID 0x7917, one controller with device ID 0x43BD and NVMe (one controller per NVMe) 11 (One controller with Device ID 0x7916, one controller with device ID 0x43BD and NVMe (one controller per NVMe) Supported AMD Controllers AMD SP3-Series Chipsets AMD AM4-Series Chipsets Systems used for testing 6 AMD Family 17h Model 01h Rev B1, SP3 processor based platform code-named “Whitehaven” AMD Family 17h Model 01h Rev B2, AM4 processor based platform code-named “Myrtle”. AMD Family 17h Models 10h-1Fh, AM4 processor based platform code-named “Myrtle” AMD Family 15h Models 60h-6Fh, AM4 processor based platform code-named “Myrtle” General Information Chapter 1 56268 Rev. 1.02 April 2018 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Table 2. Information about Supported Configuration by Installer SoC SATA Mode Promontory SATA Mode NVMe RAID Mode SATA RAID Support NVMe RAID Support AHCI / Auto AHCI / Auto Disabled No No RAID RAID Enabled Yes Yes Maximum Device Support: • Max support of 14 including both NVMe and SATA Maximum Supported Controllers: • Eight NVMe controllers + two SoC controllers + one PT controller when all set to RAID in BIOS 1.3 Generic System Setup A generic system setup process is described below. 1. Copy the AMD-RAID drivers to a removable storage medium. (Refer to Section 2.1) 2. Power-on the system. 3. Access the platform BIOS window for the system a. RAID Mode shall be enabled on the system after Configuring BIOS settings as mentioned in Section 3.1. b. This enables the loading of the AMD-RAID UEFI driver 4. Initialize the disks, using the RAIDXpert2 Configuration Utility (HII) or UEFI shell. 5. Create arrays, using the HII Configuration Utility or UEFI shell. (Refer to Section 4.1) 6. Load the AMD-RAID drivers during the operating system installation. (Refer to Section 5.1). 7. Complete the rest of the operating system installation. 8. Install the OS RAID Management Suite (AMD RAIDXpert2). (Refer to Section 6.1) IMPORTANT: To protect your data; always perform a backup prior to installing any new, major hardware or software. If you are adding NVMe as RAID to your existing RAID arrays then update all existing RAID controller drivers to latest version and reboot the system. Later connect NVMe and install RAID driver on the NVMe devices or download driver software form vendor support page. Revision History 7 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Chapter 2 56268 Rev. 1.02 April 2018 BOOTABLE ARRAYS Note: Before beginning, Have the Windows® operating system installation media available and ready to install. Note: Windows: Removable storage (Flash Drive) required for Copying AMD -RAID drivers 2.1 Copy AMD-RAID Drivers to a Removable Storage Medium: Windows® A removable storage medium is needed to copy AMD RAID drivers required for OS installation onto an AMD-RAID bootable array. 1. Power-on the system. 2. Locate and use a system that is running a Windows operating system and has a CD DVD drive or an I/O port for removable storage media (such as a USB flash drive). 3. Insert the storage medium into the system: Windows 10: Connect a USB flash drive to a USB I/O port, or insert a blank CD-DVD disk into the applicable drive. 4. Go to a browser and access the web site of your system supplier or motherboard vendor. 5. Download the AMD-RAID drivers from the web site to the appropriate removable storage medium. 6. Proceed to Windows Install and load AMD-RAID drivers during a Windows OS installation. 8 BOOTABLE ARRAYS Chapter 2 56268 Rev. 1.02 April 2018 Chapter 3 3.1 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Pre-Installation Steps Platform BIOS Settings - Enable RAID for the AMD SP3-Series Chipsets Note: The steps to configure a system to RAID mentioned here are specific to AMD NDA BIOS based off the AMI BIOS. 1. Power-on the system. 2. Press Delete or ESC to get into the Platform BIOS setup page. 3. In the BIOS setup: a. Select the Advanced tab, then press Enter b. Select the AMD PBS tab, then press Enter c. Set NVMe RAID Mode to Enabled 4. In the BIOS setup: a. Select the Advanced tab, then press Enter b. Select the AMD CBS tab, then press Enter c. Select FCH Common Options, then press Enter d. Select SATA Configuration Options, then press Enter e. Set SATA Controller to Enabled. 5. In the BIOS setup: a. Select the Advanced tab, then press Enter b. Select the AMD CBS tab, then press Enter c. Select FCH Common Options, then press Enter d. Select SATA Configuration Options, then press Enter e. Set SATA Mode to RAID. 6. In the BIOS setup: a. Select the Advanced tab, then press Enter b. Select Promontory Common Options, then press Enter c. Select PT SATA Configuration Options, then press Enter d. Set PT SATA Port Enable to Enabled. 7. In the BIOS setup: a. Select the Advanced tab, then press Enter b. Select Promontory Common Options, then press Enter c. Select PT SATA Configuration Options, then press Enter d. Set PT SATA Mode to RAID. 8. In the BIOS setup: Revision History 9 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems 56268 Rev. 1.02 April 2018 a. Select the Advanced tab, then press Enter b. Select CSM Configuration, then press Enter c. Set CSM Support to Enabled 9. In the BIOS setup: a. Select the Advanced tab, then press Enter b. Select CSM Configuration, then press Enter c. Set Boot Option Filter to UEFI and Legacy or UEFI Only. 10. In the BIOS setup: a. Select the Advanced tab, then press Enter b. Select CSM Configuration, then press Enter c. Set Storage -> UEFI 11. Save (F4) the setting and restart the system. 3.2 Platform BIOS Settings – Enable RAID for the AMD Socket AM4-Compatible Processors Note: The steps to configure a system to RAID mentioned here are specific to AMD NDA BIOS based off the Insyde BIOS. 1. 2. 3. 4. Power-on the system Press ESC to enter the System BIOS setup page Select Setup Utility, then press Enter In the BIOS setup: a. Select the Advanced tab b. Select IDE Configuration, then press Enter c. Set SATA Configure as to RAID, then press Enter d. Set Force RAID Mode to Enabled, then press Enter 5. In the BIOS setup: a. Select the Boot tab b. Set Boot Type to UEFI Boot Type, then press Enter c. Set EFI Device First to Enable, then press Enter 6. In the BIOS setup: a. Select the AMD-PBS tab b. Set NVME RAID Mode to Enabled, then press Enter 7. In the BIOS setup: a. Select the AMD-CBS tab b. Select FCH Common Options, then press Enter c. Select SATA Configuration Options, then press Enter d. Set SATA Controller to Enabled, then press Enter 10 Pre-Installation Steps Chapter 3 56268 Rev. 1.02 April 2018 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems e. Set SATA Mode to RAID, then press Enter 8. In the BIOS setup: a. Select the AMD-CBS tab b. Select Promontory Common Options, then press Enter c. Select PT SATA Configuration Options, then press Enter d. Set PT SATA Port Enable to Enabled, then press Enter e. Set PT SATA Mode to RAID, then press Enter 9. Save and restart. Revision History 11 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Chapter 4 4.1 56268 Rev. 1.02 April 2018 Create the Bootable Virtual Disk RAIDXpert2 Configuration Utility (HII Mode) For the AMD Ryzen™ Threadripper™ Processor Note: The steps to configure arrays in RAID mode mentioned here are specific to AMD NDA BIOS and are based off AMI BIOS. 1. Power-on the system. a. Press ESC or DEL to get into the Platform BIOS b. Select the Advanced tab c. Select RAIDXpert2 Configuration Utility, then press Enter 2. At the RAIDXpert2 Configuration Utility’s Main Menu, use the arrow keys to select Array Management, then press Enter 3. Use the arrow keys to select Create Array, then press Enter 4. Select Select RAID Level, then press Enter a. From the Select RAID Level drop down menu, use the arrow keys to select the desired RAID level, then press Enter 5. Select the disks with which to create the array: a. Use the arrow keys to select Select Physical Disks, then press Enter b. To select individual disks, highlight a disk with the arrow keys and press the Space Bar or Enter. Any number of disks may be selected using this method c. To select all disks, use the arrow keys to select Check All, then press Enter d. Use the arrow keys to select Apply Changes, then press Enter 6. Select an array size by doing the following: a. Use the arrow keys to select Array Size, then press Enter b. The Array size will default to the Maximum size allowed by the number of physical disks and RAID level selected. If you want a smaller size Array size, enter the desired value. c. Press Enter when the desired size is reached. 7. Use the arrow keys to select Cache Tag Size a. Any Array with only HDD/SSD will have default CTS of 64 k b. Any Array with only NVMe or NVMe with HDD/SSD will have default CTS of 256 k 8. Using the arrow keys to select Read Cache Policy, then press Enter a. Select the desired Read Cache Policy, then press Enter 9. Using the arrow keys to select Write Cache Policy, then press Enter a. Select the desired Write Cache Policy, then press Enter b. Use the arrow keys to select Create Array, then press Enter 12 Create the Bootable Virtual Disk Chapter 4 56268 Rev. 1.02 April 2018 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems 10. After completion of array creation save and reboot the BIOS 4.2 RAIDXpert2 Configuration Utility (HII Mode) For the AMD Ryzen™ Desktop Processor Note: The steps to configure arrays in RAID mode mentioned here are specific to AMD NDA BIOS based off Insyde BIOS. 1. Power-on the system. a. Press ESC to get into the Platform BIOS b. Select Device Management, then press Enter c. Select RAIDXpert2 Configuration Utility, then press Enter 2. At the RAIDXpert2 Configuration Utility’s Main Menu, use the arrow keys to select Array Management, then press Enter 3. Use the arrow keys to select Create Array, then press Enter 4. Select Select RAID Level, then press Enter From the Select RAID Level drop down menu, use the arrow keys to select the desired RAID level, then press Enter 5. Select the disks with which to create the array: Use the arrow keys to select Select Physical Disks, then press Enter To select individual disks, highlight a disk with the arrow keys and press the Space Bar or Enter. Any number of disks may be selected using this method To select all disks, use the arrow keys to select Check All, then press Enter Use the arrow keys to select Apply Changes, then press Enter 6. Select an array size by doing the following: Use the arrow keys to select Array Size, then press Enter The Array size will default to the Maximum size allowed by the number of physical disks and RAID level selected. If you want a smaller size Array size, enter the desired value. Press Enter when the desired size is reached. 7. Use the arrow keys to select Cache Tag Size a. Any Array with only HDD/SSD will have default CTS of 64 k b. Any Array with only NVMe or NVMe with HDD/SSD will have default CTS of 256 k 8. Using the arrow keys to select Read Cache Policy, then press Enter Select the desired Read Cache Policy, then press Enter 9. Using the arrow keys to select Write Cache Policy, then press Enter Select the desired Write Cache Policy, then press Enter 10. Use the arrow keys to select Create Array, then press Enter 11. After completion of array creation save and reboot the BIOS Revision History 13 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems 4.3 56268 Rev. 1.02 April 2018 UEFI Mode 1. At the system’s Power-On Self-Test (POST) screen, press F7 / F12 / ESC (or similar) to access the UEFI Configuration Utility (aka UEFI Boot Manager). 2. Boot to the EFI Internal shell Note: obtain the rcadm.efi file from your system supplier or motherboard vendor and copy it onto a UEFI flash drive, in the root directory . 3. Enter fsx: where x is the number of the UEFI Flash Drive. 4. Use rcadm to create the desired Boot Virtual Disk. Examples: Note: the user may have to press the page up key to see more of the infor mation. a. Query the devices connected in the system: (Output will display the UEFI Versio n, physical devices and arrays) rcadm.efi –M -qa b. Create a Volume on disk 1 with a size of 80 Gbs and disables Read/Write Cache: rcadm.efi –C –v –d 1 –s 80000 –ca nc c. Create a RAID0 on disks 1, 2 with a size of 10 0 Gbs and enables Read Cache: rcadm.efi –C –r0 –d 1 2 –s 100000 –ca r d. Create a RAID1 on disks 2, 3 with a max size available and enables Read/Write Cache: rcadm.efi –C –r1 –d 2 3 –ca rw e. Create a RAID10 on disks 1, 2, 3, 4 with a size of 125 Gbs and enables Write Cache: rcadm.efi –C –r10 –d 1 2 3 4 –s 125000 –ca w 14 Create the Bootable Virtual Disk Chapter 4 56268 Rev. 1.02 April 2018 Chapter 5 5.1 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Install AMD-RAID Drivers Windows®: Install AMD-RAID UEFI Drivers during Windows® OS Installation Install the AMD-RAID UEFI drivers during Windows 10 OS Installation Note: The windows described in this guide are typical. Path names and text can vary, depending on user-designated selections and other parameters. Note: NVMe devices will be listed in the “Where do you want to install Windows?”, do not delete any of the partitions or format the NVMe devices. Doing so will delete the AMDRAID metadata and the desired RAID level will be deleted. Once the AMD-RAID drivers (rcbottom and rcraid) have been loaded, a valid AMD- RAID Virtual Disk will appear. 1. Power-on the system. Create a bootable array, see Chapter 4. 2. Insert the Microsoft Windows operating system CD -ROM or DVD into the system’s CD or DVD drive. 3. Boot the system and allow it to access the Microsoft Windows operating system CD ROM or DVD. 4. At the Windows setup window: • Select the language, time and keyboard options • Click Next • Click Install Now or similar • If prompted, select the desired Operating System • Click Next • Insert the storage medium with the AMD-RAID drivers into the USB port or applicable system drive. • Click Browse • Navigate to the directory containing the saved AMD-RAID drivers • Click OK Note: If the installation has multiple controllers, there will be two or more rcbottom.inf’s listed . • Select the first AMD-RAID Bottom Device (rcbottom.inf) driver in the list • Click Next 5. At the Load Driver Warning message Chapter 5 Install AMD-RAID Drivers 15 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems 56268 Rev. 1.02 April 2018 • Click OK 6. At the Select the Driver to install window • Click Browse • Navigate to the directory containing the saved AMD-RAID drivers • Click OK • Select the AMD-RAID Controller (rcraid.inf) driver in the list • Click Next • Select (Check Mark) I Accept the License Terms • Click Next • Select Custom: Install Windows Only (advanced) or similar 7. Once both drivers have been loaded, a valid Virtual Disk appears: • Click Load Drivers • Click Browse • Navigate to the directory containing the saved AMD-RAID drivers • Click OK • Select the AMD-RAID Config Device (rccfg.inf) driver from the list • Click Next 8. At the Where do you want to install Windows • Click Next 9. Follow the on-screen instructions to complete the installation of the applicable Windows operating system. 10. After the OS is installed, Open Device Manager and verify the following: • Expand Storage Controllers: there will be an entry(ies) listed as AMD-RAID Bottom Device • Expand Storage Controllers: there will be an entry(ies) listed as AMD-RAID Controller • Expand System Devices: there will be an entry listed as AMD-RAID Config Device 11. Remove the storage medium and Microsoft Windows OS CD -ROM or DVD from the applicable drive(s) or port. 12. Proceed Installing the AMD RAIDXpert2 Management Suite for Windows ®, Refer to Chapter 6. 16 Install AMD-RAID Drivers Chapter 5 56268 Rev. 1.02 April 2018 Chapter 6 6.1 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Install the AMD-RAIDXpert2 Management Suite and Web GUI Windows® – AMD-RAIDXpert2 Management Suite Obtain the latest Catalyst executable file from your system supplier or motherboard vendor. Download the file to the system’s desktop, execute it and follow the on-screen prompts. 6.1.1 Windows® – AMD-RAIDXpert2 Management Suite 1. Obtain the latest Catalyst executable file from your system supplier or motherboard vendor. 2. Download the file to the system’s desktop, execute it and follow the on-screen prompts. 3. Click on the RAIDXpert2 Desktop Icon 4. Select the applicable language from the drop-down menu (defaults on English) 5. Default credentials are: • Username – admin • Password – admin 6. Change the credentials: • Create new username • Create new password 7. Re-log into the system with the new credentials. 6.1.2 Windows® – AMD RAIDXpert2 Management Suite Installation (Manually) 1. Obtain the AMD RAIDXpert2 Management Suite executable file (Setup.exe) from your system supplier or motherboard vendor. Download Setup.exe to the system’s desktop. 2. Install AMD RAIDXpert2 (setup.exe) by: • Open a command prompt, must be run as Administrator • cd C:\User\User_Name\Desktop • For silent installation: setup.exe • For GUI installation: setup.exe -i gui Note: For the Web GUI to function correctly, rc_cgi and apache must be running. 3. Turn off Windows Firewall (or unblock during step 2). Chapter 6 Install the AMD-RAIDXpert2 Management Suite and Web GUI 17 AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems 56268 Rev. 1.02 April 2018 4. Click on the RAIDXpert2 Desktop Icon Default credentials are: • Username – admin • Password – admin Change the credentials: • Create new username • Create new password 5. Re-log into the AMD RAIDXpert2 Management Suite or Web GUI with the new credentials. 18 Install the AMD-RAIDXpert2 Management Suite and Web GUI Chapter 6
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Author : AMD Create Date : 2018:04:17 16:05:47-05:00 Keywords : AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems, 56268 Modify Date : 2018:04:17 16:30:48-05:00 Subject : AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Producer : Microsoft® Word 2016 Format : application/pdf Title : AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Creator : AMD Description : AMD NVMe/SATA RAID Quick Start Guide for Windows® Operating Systems Creator Tool : Microsoft® Word 2016 Metadata Date : 2018:04:17 16:30:48-05:00 Document ID : uuid:1EA04450-1025-4256-847E-2DB9659C826A Instance ID : uuid:3e730a18-25d3-49a8-bcf0-a9db779ec05b Page Layout : SinglePage Page Count : 18EXIF Metadata provided by EXIF.tools