Black Jack Self Adhesive Flashing Tape
Blackjackselfadhesive Flashing Tape BlackJackSelfAdhesive Flashing Tape BlackJackSelfAdhesive Flashing Tape PDF cabp
2016-04-20
: Pdf Black Jack Self Adhesive Flashing Tape Black Jack Self Adhesive Flashing Tape Everbuild DataSheets PDF
Open the PDF directly: View PDF 
.
Page Count: 2
TECHNICAL DATA SHEET NO: FLASH VERSION: 2/1ST APRIL 1999
PAGE: 1 OF 2 DATE OF ISSUE: 3/12/2013
Product Description
A strong self-adhesive flashing tape comprising of an aluminium foil and a bitumen rubber adhesive.
The adhesive forms a strong waterproof seal by the simply pressing the tape into place by hand.
Benefits
Replaces need for lead flashing.
Self-adhesive - requires no separate glue.
Areas For Use
General repair to existing flashing.
Flashing bituminous felt and similar roofs.
Flashing parapet walls.
Sealing roof glazing.
Replacement off lost lead flashing.
Repairs to cracks in concrete.
Repairs to lead gutters.
Sealing capping bolts in roof sheets.
Sealing roof ridges.
Protective coating to insulation materials.
Sealing projections through roofs and similar sections.
Flashing between timber and brickwork or blockwork or blockwork cavities.
Flashing of skylights
Limitations
Prime porous surfaces with BLACK JACK BITUMEN AND FLASHING PRIMER.
Do not apply to damp surfaces.
In cold weather or storage conditions, adhesion may be reduced. Bring up to temperature or heat
bitumen adhesive layer with a hot air blower to improve adhesion.
Colour
Product Code
Pack Size
Box Qty
Lead Look
FLAS075
75mm x 10Mtr
8
FLAS100
100mm x 10Mtr
6
FLAS150
150mm x 10Mtr
4
FLAS225
225mm x 10Mtr
2
FLAS300
300mm x 10Mtr
2
FLAS450
450mm x 10Mtr
1
FLDIY100
100mm x 3Mtr
6
FLDIY150
150mm x 3Mtr
4
FLDIY225
225mm x 3Mtr
2
BLACK JACK SELF ADHESIVE FLASHING – TRADE & DIY ROLLS
TECHNICAL DATA SHEET NO: FLASH VERSION: 2/1ST APRIL 1999
PAGE: 2 OF 2 DATE OF ISSUE: 3/12/2013
Surface Preparation
All surfaces must be dry, sound and free from oil, grease and dust Remove all loose material by
scraper or wire brush. Porous surfaces, such as concrete or brick, should be primed using BLACK JACK
BITUMEN AND FLASHING PRIMER and allowed to dry.
Application
Cut to the required length. Peel beck approximately 5cm of release carrier and place the tape into
position. Continue removing the release carrier whilst firmly placing the tape to avoid unnecessary
creasing. Ensure intimate contact and that no air is trapped. Using a small roller ensure that all edges
and overlaps are sealed properly. Overlaps should be at least 25mm.
Specific Data
Finish
Simulated lead
Foil Thickness
50 microns
Adhesive Thickness
1.3mm
Elongation
15%
Tape Strength
3.5 N/mm
Bond Strength To Primed
Concrete
3.5 N/mm
Flexibility at -15°C
No cracking
Application Temperature
Range
5 to 40°C
Service Temperature Range
-10 to 80°C
Weight
1.4 kg/m²
Health & Safety
Consult MSDS for full list of hazards.
Storage
Store in original container in cool dry conditions. Keep away from sources of ignition.
Shelf Life
24 months from date of manufacture in tightly sealed, undamaged containers.
The technical data contained herein is based on our present knowledge and experience and we cannot be held liable for any
errors, inaccuracies, omissions or editorial failings that result from technological changes or research between the date of issue
of this document and the date the product is acquired. Before using the product, the user should carry out any necessary tests in
order to ensure that the product is suitable for the intended application. Moreover, all users should contact the seller or the
manufacturer of the product for additional technical information concerning its use if they think that the information in their
possession needs to be clarified in any way, whether for normal use or a specific application of our product. Our guarantee
applies within the context of the statutory regulations and provisions in force, current professional standards and in accordance
with the stipulations set out in our general sales conditions. The information detailed in the present technical data sheet is given
by way of indication and is not exhaustive. The same applies to any information provided verbally by telephone to any
prospective or existing customer.
