DJO Foundation Total Knee Surgical Technique
2015-06-09
: Pdf Foundation Knee Surgical Technique Foundation_Knee_Surgical_Technique 6 2015 pdf
Open the PDF directly: View PDF 
.
Page Count: 14
| Download | |
| Open PDF In Browser | View PDF |
TM Foundation® Total Knee Surgical Technique Contributing Surgeon Table of Contents Gary M. Ferguson, M.D. Clinical Assistant Professor Brown University Providence, RI Design Rationale Richard J. Friedman, M.D., FRCS(C) Professor of Orthopaedic Surgery Medical University of South Carolina Charleston, SC Surgical Technique 10 Femoral Preparation 10 Joseph Longo, MD Clinical Instructor Phoenix Orthopaedic Residency Training Program VA Medical Center Phoenix, AZ Preoperative Planning Tibial Preparation Component Implantation 2 8 14 18 Wound Closure 22 Cruciate Sacrificing P.S. 23 DJO Surgical 9800 Metric Boulevard Austin, TX (800) 456-8696 www.djosurgical.com This brochure is presented to demonstrate the surgical technique utilized by the surgeons listed above. DJO Surgical, as the manufacturer of this device, does not practice medicine and cannot recommend this or any other surgical technique for use on a specific patient. The choice of the appropriate surgical technique is the responsibility of the surgeon performing the operation. Surgical Technique Foundation® Total Knee 1 Design Rationale Foundation® Total Knee Tibial Component The Foundation Total Knee System offers four different types of tibial components, each with different patient indications. They include: 1) a non-porous coated stemmed metal baseplate, Indications Contraindications Total joint replacement is indicated for patients suffering from disability due to: Total joint replacement is contraindicated where there is: • degenerative, post-traumatic or rheumatoid arthritis; • avascular necrosis of the femoral condyle; • infection (or a history of infection), acute or chronic, local or systemic; • insufficient bone quality which may affect the stability of the implant; • obesity; 2 38 41 63 • alcoholism or other addictions; 4 42 45 69 • materials sensitivity; 6 44 48 74 • loss of ligamentous structures; 8 47 51 79 • high levels of physical activity (e.g. competitive sports, heavy physical labor); 10 50 54 84 12 53 58 89 • pregnancy. Femoral Component The patellar groove is extended so that in flexion, when the stresses on the patella are the highest, the patella will articulate along its entire profile, providing large surface area contact between the femur and patella. This is intended to reduce wear on the patella flanges in high degrees of flexion. The patellar groove 2 Tibial Component M-L Dims (mm) For cemented components - Encore recommends PMMA based bone cement. The femoral component has a 9mm distal and posterior thickness in order to conserve the amount of bone removed from the femur, and maintain equal flexion and extension gaps. The femur is made of CoCr, which was chosen for its superior wear characteristics, and is available in both porous and non-porous versions. The metal baseplate designs utilize modular inserts resulting in 9mm, 11mm, 13mm, 15mm and 19mm thicknesses. A-P Dims (mm) • moderate valgus, varus or flexion deformities. The Foundation Femoral Component was designed as a primary total condylar knee replacement. The main objectives of the femoral component are to resurface the distal femur with minimum bone removal and to provide sound articulating surface geometry for both the condylar and patellar articulations, all with minimum interference to surrounding soft tissue. By designing to these objectives, the Foundation Femoral Component can aid in reestablishing anatomical alignment and normal knee kinematics, and restoring function to the knee. 4) a stemmed all-poly component. Lateral Medial A-P Dims (mm) • muscular, neurological or vascular deficiencies, which compromise the affected extremity; While total knee replacements are not intended to withstand activity levels and loads of normal healthy bone, they are a means of restoring mobility and reducing pain for many patients. 3) a porous coated resurfacing metal baseplate and Size (left/right) • post-traumatic loss of joint configuration, particularly when there is patellofemoral erosion, dysfunction or prior patellectomy; This device may also be indicated in the salvage of previously failed surgical attempts. 2) a porous coated stemmed metal baseplate, Common to each of the four types of tibial 2 components in the system is an asymmetrical tibial profile. This feature is indicative of the an atomical shape of the tibial plateau and, therefore, maximizes coverage while minimizing baseplate overhang which may adversely affect surrounding soft tissue. All designs also have a posterior notch for retaining the posterior cruciate ligament. depth, which is designed to provide full surface contact with the patella in flexion, decreases gradually with extension as loads diminish. In addition, the patellar groove is set at a 6° angle to replicate normal anatomy. The Foundation Femoral Component comes in six sizes and in lefts and rights to provide for versatility in matching the patient’s anatomy. Each femoral component size can be used with each size Foundation Tibial Component. The dimensions of the femoral components are illustrated below: Tibial Design Each of the tibial designs offers features unique to their specific application. Stemmed Baseplate, Porous and Non-Porous: • Keeled Stem: The stem has a rounded anterior face that matches the endosteal anatomy of the anterior tibia to avoid impingement with endosteal bone. The wings of the keel angle back posteriorly to support the baseplate under the condylar bearing surface of the tibial plateau adding strength to the baseplate as well as rotational stability. These wings also place the stem in the strongest bone on the tibial plateau, thus optimizing the resistance to rotational forces. • Four Screw Holes: There are currently four screw holes in the porous stemmed baseplate for use with Encore 6.5mm cancellous bone screws to enhance fixation. • Coatings: The stemmed baseplate is offered in porous coated and non-porous coated versions. Femoral Component Size (left/right) A-P Dims (mm) Box Dims (mm) M-L Dims (mm) 2 54 37 58 4 59 41 64 6 63 45 69 8 68 49 74 10 73 53 79 12 74 57 84 • Material: The porous tibial component is made of Ti6Al4V, while the non-porous component is made of CoCr. Stemmed All-Poly Tibia: • Five Thicknesses: 9mm, 11mm, 13mm, 15mm and 19mm. • Keeled Stem: The stem shape is a winged-keel with a rounded anterior face that contours anatomically with the anterior tibial endosteal bone. The wings angle back posteriorly into the strongest bone in the tibia to provide rotational stability. • Cement Grooves: Grooves placed on the inferior surface of the component enhance cement fixation. • Normalization Steps: Normalization steps on the stem optimize cement compression. • Material: UHMWPE Resurfacing Baseplate: • Four Pegs: The four pegs on the distal surface of the component provide rotational stability. • Two Screw Holes: Two screw holes on the distal surface of the component can be used with Encore 6.5mm cancellous bone screws to enhance fixation of the component to the tibial plateau. The screw holes are located over the condylar bearing region of the tibial plateau where the bone is the strongest. • Coating: The resurfacing baseplate is porous coated. • Material: Ti6Al4V. Surgical Technique Foundation® Total Knee 3 Design Rationale Foundation® Total Knee Patellar Components Modular Tibial Inserts The Foundation Patellar Components come in a resurfacing and recessing version, as well as a porous coated metal backed version. The profile for all of the Foundation Patellar Components mates with the geometry of the patellar groove on the Foundation Femoral Component to optimize the contact area between the patella and the femoral component. Foundation Patellar Components utilize the same instrumentation. All three styles of patellas are available in 5 diameters (26mm, 29mm, 32mm, 35mm, and 38mm). The Foundation Primary Tibial Insert comes in 6 sizes and is made of ultra-high molecular weight polyethylene (UHMWPE). Each insert size is offered in 5 standard thicknesses, resulting in tibial assemblies of 9mm, 11mm, 13mm, 15mm and 19mm. The minimum thickness for the 9mm insert is 6.0mm (the label for the insert thickness refers to the overall thickness of the insert/baseplate assembly). The tibial inserts are neutral in orientation. That is, they do not come in lefts and rights. This unique combination provides the advantages of an asymmetrical tibial coverage without the excessive insert inventory usually seen when including this design feature. The articulating geometry of the tibial insert is semi-constrained. The advantages of a semiconstrained tibial profile may include an increase in contact area with the conforming femoral component, as well as an increase in posterior shear stability. The Foundation Knee has been designed to withstand forces that surpass the maximum posterior shear forces reported during the normal gait cycle. This design feature is not common to most of the contemporary knee designs on the market, and may provide a safety mechanism in the event of a deficient posterior cruciate ligament. The tibial baseplate and insert assemble via a sound locking mechanism, which utilizes posterior feet and a three-segment anterior snap on the inside wall of the baseplate. In addition, the inserts are secured with a self-locking attachment screw which will provide further security to the baseplate/insert assembly. The central eminence on the tibial insert is uniquely designed to provide 10 to 15 degrees of rotation with every size combination of femoral and tibial components. Each primary insert has a posterior notch cut out for a retained posterior cruciate ligament. In addition, when using the PCL retaining option, any size femoral component can be utilized with any size tibial component. Trials are available for the tibial inserts and are color coded for easy reference intraoperatively. The color codes are illustrated below: Insert Components 4 Size Trial Color 2 Rust 4 Green 6 Blue 8 Gray 10 Black 12 Brown To enhance fixation, three pegs are present on the inferior surface of the patella. The shape of the patella is a symmetrical flange to improve patellar contact with the femoral condyles, particularly at high angles of flexion. The symmetrical geometry by nature requires no rotational alignment in reference to the femoral component and allows the three pegs to be placed in the optimum position. All-poly versions of the Foundation Patella have grooves on the inferior surface of the patella as well as on the pegs to enhance cement fixation. Trials are available for the tibial inserts and are color coded for easy reference intraoperatively. Patellar Components Style Trial Color All-Poly - Thin (8mm-9mm) Green All-Poly - Thick (10mm) Gray Metal-Backed (10mm) Black PCL Substituting (P.S.) Design Considerations P.S. Femoral Component The Foundation Femoral P.S. Component was designed as a primary posterior cruciate substituting component. The main objectives of the femoral component are to resurface the distal femur with minimum bone removal while inducing posterior rollback and providing resistance to posterior subluxation, functions that are normally present when the posterior cruciate ligament is intact. The P.S. Femoral Component is also designed to provide sound articulating surface geometry for both the condylar and patellar articulations, all with minimum interference to surrounding soft tissue. By designing to these objectives, the Foundation P.S. Femoral Component can aid in reestablishing anatomical alignment, normal knee kinematics, and restoration of function. Surgical Technique Foundation® Total Knee 5 Design Rationale Foundation® Total Knee Modular P.S. Tibial Insert The modular Foundation P.S. Tibial Insert, made of UHMWPE, is designed to work with the Foundation Stemmed Tibial Components to complete the P.S. option of the Foundation Total Knee System. The primary objectives considered in the design of the tibial inserts are providing a smooth articulating surface for the P.S. Femoral Component, optimizing contact area and providing the required motion of the femoral component on the tibia. In addition, the tibial spine is designed to restore the function of posterior rollback while preventing posterior subluxation of the tibia. The P.S. insert meets these objectives along with providing a sound modular attachment of the insert to the tibial component. P.S. Femoral Component The distal and posterior thicknesses of the femoral component are each 9mm. This thickness was chosen to conserve the amount of bone removed from the femur and to ensure that the flexion and extension gaps remain equal. The femoral component is made of CoCr, which was chosen for its superior wear characteristics. The Foundation P.S. Femoral Component is manufactured with a highly polished finish on all exterior/articulating surfaces. The interior surfaces have a roughened-blasted surface to enhance cement fixation. The Foundation P.S. Tibial Insert comes in 6 sizes corresponding to the baseplate sizes. Each size is offered in 5 thicknesses, resulting in tibial assembly thicknesses of 9mm, 11mm, 13mm, 15mm and 19mm. The minimum poly thickness on the 9mm insert is 6.0mm. (The insert thickness refers to the overall thickness of the insert/baseplate assembly.) The tibial inserts are neutral in orientation. That is, they do not come in lefts and rights. This unique combination provides the advantages of asymmetrical tibial coverage offered by the tibial baseplate without the massive insert inventory usually seen when including this design feature. The patellar groove of the Foundation P.S. Femoral Component is deepened to minimize advancement of the patellar mechanism, which can inhibit flexion. The deepened patella groove aims to allow the patella to be returned to its anatomical position, which in turn seeks to encourage full flexion and also provide increased stability to the patellar component in resistance to lateral subluxation or dislocation. The patellar groove is set at a 6° angle to replicate normal anatomy. The patellar groove depth is designed to provide full surface contact with the patella in flexion and to decrease gradually with extension as loads diminish. The P.S. Femoral Component comes in 6 sizes and in lefts and rights to provide for versatility in matching the patient’s anatomy. Size compatibility allows for going up and down one size when matching a P.S. tibial insert with a P.S. femoral component. For example, a size 6 femoral component can be used with a size 4, 6 or 8 tibial insert only. The sizing and interchangeability are illustrated to the right. The cam/spine geometry is designed to induce rollback of 7-16mm, depending on the size, and allows +/-15° of internal/external rotation. The femoral cam is designed to engage the tibial spine at 60° flexion and to allow for 130° of flexion. The femoral instrumentation for the Foundation cruciate retaining femoral component is the same as for the Foundation P.S. Femoral Component. Only one additional step is needed to prepare the femur for the P.S. Femoral Component. This one extra step is accomplished with a box cutting guide and chisel or 1/2” blade, which along with the trials are the only instrumentation additions necessary to the primary knee instruments for implanting a Foundation P.S. Knee. The box height on the femoral component is 15mm and the box width is 22mm. The box on the femoral component is open. The advantage to an open box is to provide access to the femoral canal in case of traumatic injury requiring a femoral rod. 6 P.S. Femoral Component Size P.S. Insert Size Compatibility 2 2, 4 4 2, 4, 6 6 4, 6, 8 8 6, 8, 10 10 8, 10, 12 12 10, 12 The tibial baseplate and insert assemble via a sound locking mechanism that utilizes posterior feet and a three-segment anterior snap on the inside wall of the baseplate. In addition, a self-locking attachment screw is used that provides further security to the baseplate/insert assembly. The pathway for the attachment screw assembly is straight through the tibial spine into the baseplate providing ideal resistance to any potential tilting forces placed on the insert/baseplate assembly. The tibial spine is 8mm higher than the femoral cam at full flexion. The significance of the spine height at full flexion is the amount of tibial spine to be “jumped” by the femoral component to cause dislocation of the femur. As an alternative, an Ultra-Congruent tibial insert is available as PCL substituting insert option to be used with the PCL retaining femur. This insert is a deep-dish design with a 12mm anterior lip height. This high anterior lip helps prevent tibia subluxation in the case of an absent or resected PCL. These inserts are available in 5 standard thicknesses, resulting in tibial assemblies of 9mm, 11mm, 13mm, 15mm, and 19mm. These inserts will stabilize the knee in the absence of the PCL, and provide the full range of motion without the need to remove more femoral bone, as is standard with more conventional P.S. systems. Trials are available for the tibial inserts and are color coded for easy reference intraoperatively. The color codes are illustrated to the right. P.S. Tibial Insert Trials Size Color 2 Rust 4 Green 6 Blue 8 Gray 10 Black 12 Brown Surgical Technique Foundation® Total Knee 7 Preoperative Planning Foundation® Total Knee Minimally Invasive Surgical Exposure Preoperative Planning Sufficient surgical exposure is critical in total knee arthroplasty. Adequate exposure allows bony landmarks, component alignment and soft tissue evaluation to be assessed more thoroughly and can, therefore, contribute to more successful results. Use a long-standing radiograph to evaluate the angle between the mechanical axis of the leg and the anatomic axis of the femur. The normal mechanical axis is formed by a straight line which begins at the center of the femoral head, passes through the center of the knee joint and ends at the center of the ankle. The mechanical axis will not be normal in the face of femoral, tibial, or joint space deformities. With this in mind, take care to reconstruct the normal mechanical axis on the radiograph. The angle measured between this normal mechanical axis and the axis of the femur will determine which of the IM Femoral Bushings should be used with the Distal Femoral Resection Guide (5°, 7°, or 9°) to obtain a distal femoral cut which will be perpendicular to the mechanical axis of the joint (Figure 1). The goal of this preoperative planning exercise is to restore the normal mechanical axis of the leg and create a joint plane which is parallel to the floor, while sacrificing minimal bone stock and maximizing collateral ligament balance following reconstruction. Make a longitudinal medial parapatellar skin incision. The incision should begin approximately 6cm above the most proximal portion of the patella and extending approximately 2cm below the tibial tubercle (Figure 2). Enter the knee joint through a medial parapatellar joint capsule incision and carry the incision proximally into the quadriceps tendon. Continue the capsular incision inferiorly to the medial side of the tibial tubercle to allow sufficient patellar exposure and adequate knee flexion (Figure 3 and Figure 4). Complete meniscectomy is essential for obtaining optimum exposure of the posterior tibia and also aids in restoring collateral ligament balance. Likewise, removing osteophytes from the intercondylar notch aids in identifying accurate placement of the femoral intramedullary drill hole. Removing all periarticular osteophytes on both the femoral and tibial sides should reduce the possibility of soft tissue impingement and provide the best conditions for accurate implant sizing. Templates for the Foundation Total Knee System are available to aid in preoperative implant sizing. Figure 1 Figure 2 Skin Incision 8 Figure 3 Medial Parapellar Figure 4 Surgical Technique Foundation® Total Knee 9 Surgical Technique Foundation® Total Knee Distal Femoral Resection Fix the position of the cutting block by drilling two holes through the holes marked “0” and placing pins through the holes into the femur. Holes placed in 2mm increments above and below the holes marked “0”, allow for readjustment of the cutting block to remove more or less bone as determined necessary. A general guideline for the distal femoral resection is to remove an amount of bone that results in the saw blade passing near or at the depth of the intercondylar notch. Due to anatomical differences between patients, a distal resection of 11mm is not uncommon. Open The Femoral Canal Using the IM Femoral Drill Guide and the 8mm (5/16 inch) IM Femoral Drill, locate and drill a pilot hole into the intramedullary femoral canal (Figure 5). The inferior edge of this hole should be positioned approximately 1-2mm anterior to the intercondylar notch. Placement of the hole too anterior will result in a femoral component position that is in relative extension with respect to the long axis of the femur. In contrast, placement of the hole too posterior or close to the apex of the intercondylar notch will result in a femoral component position which is in relative flexion compared to the long axis of the femur. Loosen the securing knob, remove the Distal Femoral Resection Guide, and attach the Saw Capture to the cutting block. Using a saw blade that is 1mm thick (.040 inches) and an oscillating saw, cut the distal femur (Figure 7). Insert the T-Handle IM Rod into the pilot hole created by the IM Femoral Drill. Slowly introduce the rod beyond the depth of the pilot hole until it passes through the isthmus of the femoral canal. Femoral Sizing: Posterior Reference Figure 5 Establish Femoral Alignment Select the appropriate Femoral IM Bushing (5°, 7°, or 9°), based on the preoperative measurement of valgus for the distal cut, and lock the bushing into the Distal Femoral Resection Guide. The bushing should indicate the proper setting for a left or right knee with appropriate “L” and “R” markings on the bushing facing anteriorly. Assemble the T-Handle IM Rod into the bushing selected and insert the assembly into the femoral canal. The feet on the Distal Femoral Resection Guide should be flush with the back side of the guide by turning the knobs on the front surface of the guide counterclockwise until the knobs stop. Once the guide is placed in contact with the femur, one of the feet can be extended to contact the femur and provide increased stability of the instrument. Take care not to extend the feet so far that the instrument is lifted off the distal end of the femur. This will result in an inaccurate distal resection. Secure the Distal Femoral Cutting Block at the 9mm resection line on the indicator bar (the block will click into this setting as the block slides along the indicator bar). Line markings, placed in 2mm increments along the indicator bar, allow for readjustment of the cutting block to remove more or less bone (Figure 6). Holes for the External Alignment Tower are present on the Distal Femoral Cutting Block so that an External Alignment Rod may be used to assess alignment prior to making the distal femoral cut. Proper alignment should result in the rod passing over the center of the femoral head. 10 Figure 7 Seat the Femoral Sizer on the distal femur using the sizer feet to reference the posterior condyles. Position the stylus tip on the lateral aspect of the anterior cortex of the femur and read the measurement indicator to determine the appropriate size femoral component (Figure 8). For measurements falling less than half way between sizes select the smaller size, for measurements falling more than half way between sizes select the larger size. Markings are also available on the medial and lateral arms of the sizer to indicate the M-L width of each size femoral component and to aid in the proper medial-lateral positioning of the femoral component. Figure 8 Femoral Alignment Figure 6 Place the appropriate Femoral Peg Bushing (3º or neutral), in the face of the Femoral Sizer. The 3º Femoral Peg Bushing will orient the peg holes at 3º of external rotation for either a left or right femur as indicated on the bushing. Externally rotating the femoral component will help improve patella tracking, as the natural position of the patella is slightly lateral in extension to slightly medial in flexion. The “3º L” and “3º R” markings should always be right side up when the bushing is in place. An upside down bushing will result in the holes being prepared incorrectly (Figure 9). Hold the Femoral Peg Bushing in place and drill two holes for the femoral pegs using the 6.4mm (1/4 inch) drill marked “Femoral Peg” (Figure 10). Figure 9 Figure 10 Surgical Technique Foundation® Total Knee 11 Surgical Technique Foundation® Total Knee Femoral Preparation 4-in-1 Speed Blocks Place the appropriate size 4-in-1 Speed Cut Block on the distal femur. Quick Lock Handles can be attached to the block for stabilization. As an alternative, the block may be pinned in place using the 3” Bone Pins. Make the anterior cut, posterior cut, and anterior and posterior chamfer cuts using an oscillating saw and a 1mm thick saw blade (Figure 13). Femoral Sizing: Anterior Reference Seat the Femoral Sizer on the distal femur using the sizer feet to reference the posterior condyles. Allow the anterior portion of the guide to float with the stylus tip until it is positioned on the lateral aspect of the anterior cortex of the femur. Secure the stylus tip in the correct position by tightening the Stylus Locking Knob. Turn the knurled Actuation Knob down until it is flush with the Stylus Locking Knob and read the measurement indicator to determine the appropriate size femoral component (Figure 11). For measurements falling less than half way between sizes, select the smaller size; for measurements falling more than half way between sizes, select the larger size. Markings are also available on the medial and lateral arms of the sizer to indicate the M-L width of each size femoral component. Use these markings to properly position the component medial-lateral on the femur. Place the appropriate femoral peg bushing (3º or neutral) for the size to be used into the face of the anterior sizer. The 3º Femoral Bushings will orient the peg holes at 3º of external rotation for either a left or right femur as indicated on each bushing. The “3º L” and “3º R” markings should always be right side up when the bushing is in place. An upside down bushing will result in the holes being prepared incorrectly. Hold the Femoral Peg Bushing in place and drill two holes for the femoral pegs using the 6.4mm (1/4 inch) drill marked “Femoral Peg” (Figure 12). A-P and Chamfer Blocks If the speed block has been used as described in Figure 13, place the appropriate size 1-Piece Trochlear Groove Guide in place on the distal femur (the size of the guide should match that of the 4-in-1 Speed Cut Block used). Ream the trochlear groove area with the drill marked “Trochlear” (Figure 14). To facilitate reaming, take care to balance the drill through the guide and initiate reaming prior to engaging the bone. Place the appropriate size Femoral A-P Cut Block on the distal femur. Attach the Saw Capture to the anterior surface of the block and make the anterior cut using an oscillating saw and a 1mm saw blade (Figure 15). Reposition the Saw Capture to the posterior surface of the block to make the posterior cut. Place the appropriate size Femoral Chamfer Cut Block on the distal femur. Attach the Saw Capture to the anterior surface of the block. Make the anterior chamfer cut. Reposition the Saw Capture to the posterior surface of the block to make the posterior chamfer cut (Figure 16). With the chamfer block still in place, attach the Trochlear Drill Guide to the anterior surface of the chamfer block, and ream the trochlear groove area with the drill marked “Trochlear” (Figure 17). To facilitate reaming, take care to balance the drill through the guide and initiate reaming prior to engaging the bone. Figure 11 Figure 13 Figure 14 Figure 16 Figure 17 Figure 15 Figure 12 12 Surgical Technique Foundation® Total Knee 13 Surgical Technique Foundation® Total Knee Axial Alignment Confirmation After anchoring the resection guide to the tibia, as described above, assess the position of the guide relative to the anterior tibial crest. In the absence of tibia vara, palpation of the tibial crest will reveal it to be truly parallel to the resection guide. With normal tibia vara, palpation of the crest should revel that the crest position lies just lateral to the guide proximally, just medial to the guide in the midportion, and just lateral to the guide distally. A deviation from this position may require readjustment of the resection guide. If the guide is aligned properly. Tibial Alignment Option One: Extramedullary Tibial Guide Rotational Alignment Adjust the overall length of the Extramedullary Tibial Resection Guide to the appropriate tibial length. Lightly anchor the proximal end of the resection guide onto the central tibial plateau by tapping in the long pin. Strap the ankle spring around the ankle to provide stability of the instrument distally. Establish rotational alignment by positioning the center of the T-shaped Tibial Cut Block just medial to the tibial tubercle and lightly anchor the short pin into the tibial plateau (Figure 18). Do not fully seat the short pin. A secondary rotational alignment check can be accomplished by placing a 3.2mm pin through the appropriate hole in the apex of the Ankle Cradle. Proper alignment should result in the pin running through a plane parallel to the transmalleolar axis (Figure 19). Figure 18 Tibial Slope Adjustment Adjust the height of the Tibial Cutting Block so that the cutting surface is slightly above the tibial plateau. Place a 3.2mm drill bit through one of the most proximal holes in the Tibial Cutting Block so that it extends over the articular surface. Adjust the slope on the cutting block by sliding the Extramedullary Tube along the length of the Ankle Bar until the axis of the pin runs parallel with the surface of the tibial plateau (Figure 20). Once rotational alignment and slope have been established, refer back to the proximal end of the resection guide and fully seat the pins in the tibial plateau. The most common malposition of the guide is varus; e.g. palpation of the crest shows the crest position slightly lateral to alignment guide proximally, directly behind the guide along the mid-tibia, and medial to guide distally. To correct this condition, follow the instructions outlined in step #7 for anchoring the Tibial Cut Block in place against the anterior tibia. Using the same pins that were used to anchor the Tibial Cut Block, secure the 2° Varus / Valgus Cut Block in place. This cutting block will provide a cutting surface that will correct the malalignment by 2° (Figure 21). The 2° Varus / Valgus Cut Block can be fitted with the Alignment Tower and External Alignment Rod to verify the correction. Attach the Saw Capture to the cutting block and use an oscillating saw and 1mm thick sawblade to complete the tibial resection. Figure 21 Option Two: Intramedullary Tibial Guide Figure 19 Using the IM Femoral Drill, locate and drill a pilot hole into the intramedullary tibial canal. The inferior edge of this hole should be positioned 3-5mm anterior to the pinnacle of the proximal tibial spine. Insert the T- Handle into the pilot hole created by the IM drill. Slowly introduce the rod beyond the depth of the pilot hole to open the intramedullary canal. Assemble the two-piece IM Tibial Resection Guide to achieve the desired amount of posterior slope (0° or 6°). The guide should be assembled so the slope indicators on the guide face away from the patient when the guide is in position. Next assemble the T-Handle IM Rod into the IM Tibial Resection Guide Assembly and insert the apparatus into the tibial canal. Establish rotational alignment by positioning the center of the T-shaped Tibial Cut Block just medial to the tibial tubercle and anchor the guide using 3” Bone Pins through holes on the primal portion of the alignment guide (Figure 22). Figure 22 Figure 20 14 Surgical Technique Foundation® Total Knee 15 Surgical Technique Foundation® Total Knee Tibial Sizing Proximal Tibial Resection Completely remove all tibial osteophytes prior to tibial sizing to avoid false coverage of osteophyte formation. Size the proximal tibia by matching a Tibial Sizing Template to the profile of the resected tibial plateau (Figure 26). A removable Tibial Sizer Handle can be attached to the Tibial Sizing Template, and the External Alignment Rod can be used with the Tibial Sizer Handle to confirm tibial alignment (Figure 27). Place the Tibial Stylus on the cutting block and adjust the block until the tip of the stylus marked “9mm”, denoting a 9mm resection, touches the lowest point of the least involved compartment of the tibial plateau (Figure 23). An alternative method is to adjust the block until the tip of the stylus marked “1mm” touches the lowest point of the most involved compartment of the tibial plateau. Caution: This method should not be used in cases of severe bone loss, where augmentation blocks would be appropriate. Likewise, in cases where the defect is minimal, using the 1mm stylus tip may not indicate the removal of sufficient bone stock to accommodate the Foundation Tibial Component (Figure 24). Secure the position of the cutting block by drilling two holes through the holes marked “0” and placing pins through the holes into the tibia. Holes placed in 2mm increments above and below the holes marked “0” allow for readjustment of the cutting block to remove more or less bone as determined necessary. Unlock the cutting block from the resection guide. Remove the guide from the tibia using the Slaphammer, leaving the tibial cutting block against the anterior tibia. Place the Saw Capture on the cutting block and use an oscillating saw and 1mm saw blade to complete the tibial resection (Figure 25). Holes for the External Alignment Tower are present in the Tibial Cut Block so that alignment may be assessed prior to making the tibial cut. When using the alignment tower, proper alignment is indicated by the alignment rod pointing at the second toe. Figure 26 Anchor the Tibial Sizing Template Figure 23 To ensure proper alignment of the tibial component, determine correct rotational alignment for the tibial template by performing a trial reduction with the femoral trial component and a tibial trial insert assembled into the tibial template. Alternatively, alignment can be determined by positioning the sizing template such that the External Alignment Rod passes just medial to the tibial tubercle. Using a 3.2mm drill bit, drill two holes perpendicular to the Tibial Sizing Template through the two countersunk holes on the template. Each hole should be drilled approximately 2cm deep. Insert a Headed Tibial Bone Pin through each of the holes to secure the tibial template in place (Figure 28). Use only finger pressure to seat the pins. If a mallet is used to sink the headed pins, the pins can become angulated and heads of the pins can keep the tibial trial and/or tibial broach guide from fully seating. Figure 27 Stemmed Tibial Component Figure 24 Assemble the Broach Guide Handle to the appropriate size Tibial Broach Guide and place the guide into the central detail on the tibial template. Using the Tibial Stem Reamer, ream the tibial canal to the stop (Figure 29). Center the appropriate size Tibial Broach in the hole prepared by the reamer and broach the tibial canal until the broach is fully seated (Figure 30). Figure 28 Figure 25 Figure 29 16 Figure 30 Surgical Technique Foundation® Total Knee 17 Surgical Technique Foundation® Total Knee Traditional Patellar Sizing All-Polyethylene Component Size the patella using the Patellar Sizer/Drill Guide. The center of the appropriate size patella should be positioned medial so that the highest point of the patellar dome replaces the highest point of the normal patella (Figure 33). Assemble the Broach Guide Handle to the Tibial Drill Guide marked “All-Poly” and place the guide into the central detail on the tibial template. Using the Tibial Stem Reamer, ream the tibial canal to the stop. Center the tip of the Tibial Broach, marked “All-Poly”, in the pilot hole created by the Tibial Stem Reamer. Broach the proximal tibial canal until the broach is fully seated. Patellar Peg Preparation Position the Patellar Sizer on the resected patella placing the peg holes in the desired orientation. Press the sharp pin on the Patellar/Sizer Drill Guide into the resected patella and drill for the patella pegs using the Patella Peg Stop Drill (Figure 34). Resurfacing Tibial Component Recessed Patellar Preparation Using a 3.2mm drill bit, drill four holes, approximately 1.5cm deep, for the baseplate pegs using the tibial template as a guide (Figure 31). Resurfaced Patella Preparation Figure 31 Measure the overall patella thickness using a caliper. Place the Patella Osteotomy Guide on the patella and set the stylus to indicate an amount of bone equal to the thickness of the patellar component to be used. Using an oscillating saw and a 1mm thick saw blade, resect the patella. If the initial patellar thickness measures less than 18mm, remove less bone to assure sufficient bone stock for anchoring the patellar component (Figure 32). Figure 32 18 Measure the overall patellar thickness using a caliper. Place the Patella Osteotomy Guide on the patella and set the stylus to indicate an amount of bone equal to 2mm less than the thickness of the patellar component to be used (i.e.; if a 10mm Patella is to be used, resect 8mm of bone). Using an oscillating saw and a 1mm thick saw blade, resect the patella. If the initial patellar thickness measures less than 18mm, remove less bone to assure sufficient bone stock for anchoring the patellar component. In any case, the thickness of the patella after the osteotomy should not be less than 10mm. Figure 33 Figure 34 Surgical Technique Foundation® Total Knee 19 Surgical Technique Foundation® Total Knee Tibial Component Place a layer of bone cement on the bottom surface of the tibial component. There is no need to apply cement to the keeled stem on the metal-backed components. Also place a layer of bone cement on the proximal tibia. Using the Tibial Impactor and a mallet, impact the tibial component into the tibia until it is fully seated on the tibia (Figure 39). Remove any excess bone cement paying particular attention to area where the tibial insert will be installed. Bone cement left on the proximal side of the tibial component will prohibit the insert from properly seating in the tibial tray. Patellar Sizing for Recessing Size the patella using the Patellar Sizer. The center of the appropriate size patella should be positioned medial so that the highest point of the normal patella is replaced by the highest point of the patellar dome. To ensure sufficient rim following countersinking, size the patella such that 2mm of bone will remain beyond the periphery of the patellar diameter (Figure 35). Recessing Based on the size of patella chosen, assemble the appropriate Patellar Bushing into the Patellar Clamp and position the clamp over the resected surface of the patella. Care should be taken to position the center of the bushing medially so that the highest point of the patellar component will be correctly positioned. Using the corresponding Patella Reamer, countersink the patella by 2mm by reaming the patella until the top surface of the reamer meets the first engraved line on the inside of the patellar bushing (Figure 36). To facilitate reaming, initiate power to the reamer fully before engaging bone. Apply gentle, uniform pressure to the patellar surface while reaming. This should prevent over reaming and provide a concentric inset cavity for the patellar component. Femoral Component Figure 35 Mix commercially available PMMA based bone cement. Place a layer of the cement on the internal surfaces of the femoral component. Also place a layer of cement on the distal femur. Using the Femoral Impactor and a mallet, impact the femoral component onto the femur until it is fully seated on the end of the femur (Figure 40). Remove any excess bone cement paying particular attention to the polished articulating surface of the implant. Figure 39 Patellar Component Place a layer of bone cement on the underside of the patellar component. Using the appropriate size Patella Inserter in the Patella Clamp, secure the patellar component in position and tighten the clamp (Figure 41). Leave to clamp in the secured position until the cement is hard. While the cement cures remove any excess cement from around the component. Figure 36 Patellar Peg Preparation After reaming, and without removing the Patellar Clamp, place the appropriate Patellar Drill Guide into the Patellar Bushing. Tap the drill guide into place to anchor the sharp pin into the patellar bone. Using the appropriate Patella Peg Stop Drill, drill the three peg holes (Figure 37). Figure 40 Trial Reduction Evaluation of implant fit can be accomplished by placing an appropriate size Femoral Trial, Patellar Trial, Tibial Sizing Template, and Tibial Insert Trial into the prepared joint space. The Axial Alignment Rods can then be used to assess the alignment of the joint (Figure 38). Figure 41 Figure 37 20 Figure 38 Surgical Technique Foundation® Total Knee 21 Surgical Technique Foundation Cruciate Sacrificing (P.S.) Tibial Insert Additional Considerations for PCL Femoral Box Preparation Place the insert into the tibial baseplate making sure that the posterior feet on the insert catch under the posterior lips on the baseplate. Using the Insert Impactor at a 45° angle, impact the insert into the tray. One impact should be adequate to secure the anterior locking mechanism on the implant (Figure 42). Tighten the tibial insert attachment screw (captured in the tibial insert) into tibial baseplate. The recommended applied torque to properly attach the locking screw is 45”lbs. A torque-limiting driver is provided as a minimal value torque (Figure 43). Torque applied is 45”lbs when the handle gives way and an audible click is heard. Sacrificing When implanting a PCL sacrificing component or converting from PCL retaining to a PCL sacrificing design, the following technique specific considerations should be taken into account: Choose the appropriate box cutting jig corresponding to the size of the femoral component to be used, and secure the jig on the distal femur. Using the sides of the box cutting jig as a guide, cut perpendicular to the distal femur on both sides of the box with a 1mm thick saw blade and oscillating saw. The depth of the cuts for the walls of the box should be carefully monitored using the anterior slot of the guide, which corresponds to the distal surface of the box, as a depth gage for these cuts (see Figure PS1). Place the P.S. Box Cutting Chisel into the anterior slot in the box cutting guide taking care to insert the chisel with the sharp side of the beveled tip oriented proximally. Impact the chisel until the intercondylar bone is removed (see Figure PS2). Foundation® Total Knee Primary Knee Surgical Technique 1. To aid in balancing the flexion gap, minimal slope should be placed on the tibia. Figure 42 2. Three degrees of external rotation should be placed on the femoral component via the Foundation Femoral Sizer and 3 degree bushing option. Again, this will aid in balancing the medial and lateral compartments of the flexion gap, as well as improve patellar tracking. 3. Prior to using the box cutting jig, the PCL should be excised if still present. It is recommended that this step be done after preparation of the tibia, so that manipulation of the joint is facilitated during the majority of the surgical procedure. With the above considerations in mind, the procedure can be completed as described below. Wound Closure After cement polymerization has occurred, the knee can be closed. Release the tourniquet and control bleeding. Employ a closed wound suction device for the immediate recovery period. A standard closure should now be completed using interrupted sutures and/or surgical staples. Verify the final range of motion to ensure complete flexion capabilities and the integrity of the sutures. Initial Technique Prepare the femur through step 5 of the surgical technique for the Foundation primary cruciate retaining knee. There is no need to complete the trochlear groove preparation, since the box cutting jig for the P.S. Femoral Component will remove the bone in this area. Continue on to step 6, “Tibial Alignment” and prepare the tibial plateau prior to using the box cutting jig for the P.S. Femoral Component. Follow the technique through step 10. Prior to patella preparation initial the following steps to prepare the femoral P.S. box. Technique Completion Proceed with Step 11 in the cruciate retaining primary technique. Trial reduction is accomplished in the same manner as with the retaining knee. However, the femoral component must be placed on prior to placing the insert trial. If the insert trial is difficult to place, subluxate the tibia using a PCL retractor. Figure 43 Figure PS1 22 Figure PS2 Surgical Technique Foundation® Total Knee 23 TM CAUTION: Federal Law (USA) restricts this device to sale by DJO Surgical I A DJO Global Company T 800.456.8696 D 512.832.9500 F 512.834.6300 9800 Metric Blvd. I Austin, TX 78758 I U.S.A. djosurgical.com or on the order of a physician. See package insert for a complete listing of indications, contraindications, warnings, and precautions. ©2011 Encore Medical, L.P. 0010307-001 rev. C 06/12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Author : DJO Surgical Create Date : 2012:06:20 13:47:14-05:00 Modify Date : 2014:12:19 16:30:55-06:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Instance ID : uuid:face1ad0-6174-4365-b055-1deb932ebfab Original Document ID : adobe:docid:indd:92ba889e-3332-11dd-9860-c3196499c19a Document ID : xmp.did:F0732DEC1A2068118A6D863BC2428ECD Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:9AC768D61A2068118A6D863BC2428ECD Derived From Document ID : xmp.did:7342AC9FDF20681180838758DEF1C6BD Derived From Original Document ID: adobe:docid:indd:92ba889e-3332-11dd-9860-c3196499c19a Derived From Rendition Class : default History Action : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:EA564574072068118A6DEDD417749724, xmp.iid:EB564574072068118A6DEDD417749724, xmp.iid:DBA3F2EC072068118A6DEDD417749724, xmp.iid:77A5D1EC242068118A6DEDD417749724, xmp.iid:42304A272A2068118A6DEDD417749724, xmp.iid:2C3E1374072068118083B33EEFFABB69, xmp.iid:B9AF6580082068118083B33EEFFABB69, xmp.iid:9A8CE90F092068118083B33EEFFABB69, xmp.iid:C7A9E66F102068118083B33EEFFABB69, xmp.iid:80B554D8122068118083B33EEFFABB69, xmp.iid:7DDDA004132068118083B33EEFFABB69, xmp.iid:9847C307142068118083B33EEFFABB69, xmp.iid:D2DE96A7142068118083B33EEFFABB69, xmp.iid:DFC48CB9182068118083B33EEFFABB69, xmp.iid:EDB8D3B1192068118083B33EEFFABB69, xmp.iid:11FF38511C2068118083B33EEFFABB69, xmp.iid:C072A1691D2068118083B33EEFFABB69, xmp.iid:59EEFA031E2068118083B33EEFFABB69, xmp.iid:EDA1AFE6202068118083B33EEFFABB69, xmp.iid:5C1E1C74072068118083AC50CAAC8224, xmp.iid:20547AD8092068118083AC50CAAC8224, xmp.iid:2835FD5A0C2068118083AC50CAAC8224, xmp.iid:70AEB9530E2068118083AC50CAAC8224, xmp.iid:71AEB9530E2068118083AC50CAAC8224, xmp.iid:9128F6810E2068118083AC50CAAC8224, xmp.iid:2B07A8CA0E2068118083AC50CAAC8224, xmp.iid:88080BB41120681180839CAB13C7A5A3, xmp.iid:DE40C3E91120681180839CAB13C7A5A3, xmp.iid:DF40C3E91120681180839CAB13C7A5A3, xmp.iid:E040C3E91120681180839CAB13C7A5A3, xmp.iid:04DE1C74072068118083DAD075C63C16, xmp.iid:7C587C771E20681180838A2003E94AD7, xmp.iid:7D587C771E20681180838A2003E94AD7, xmp.iid:0092719B1E20681180838A2003E94AD7, xmp.iid:97311C74072068118083C4651960AD3C, xmp.iid:98311C74072068118083C4651960AD3C, xmp.iid:C99E2098072068118083C4651960AD3C, xmp.iid:FCA57E4FACA8E011A799EDFA232FDF30, xmp.iid:FDA57E4FACA8E011A799EDFA232FDF30, xmp.iid:53F456A7CAA8E011A799EDFA232FDF30, xmp.iid:54F456A7CAA8E011A799EDFA232FDF30, xmp.iid:84B60887CBA8E011A799EDFA232FDF30, xmp.iid:44BBF789CBA8E011A799EDFA232FDF30, xmp.iid:941DFA89CBA8E011A799EDFA232FDF30, xmp.iid:951DFA89CBA8E011A799EDFA232FDF30, xmp.iid:961DFA89CBA8E011A799EDFA232FDF30, xmp.iid:D0265260CCA8E011A799EDFA232FDF30, xmp.iid:905D65A8CCA8E011A799EDFA232FDF30, xmp.iid:8178A4C811A9E011A3FF8C281FBBE447, xmp.iid:8278A4C811A9E011A3FF8C281FBBE447, xmp.iid:076B7E5C14A9E011A3FF8C281FBBE447, xmp.iid:086B7E5C14A9E011A3FF8C281FBBE447, xmp.iid:2A2974B514A9E011A3FF8C281FBBE447, xmp.iid:91A4A2902FA9E011A3FF8C281FBBE447, xmp.iid:92A4A2902FA9E011A3FF8C281FBBE447, xmp.iid:9AA4A2902FA9E011A3FF8C281FBBE447, xmp.iid:901CC55138A9E011A3FF8C281FBBE447, xmp.iid:3F0DAC6770A9E011A5CBB499B53F0338, xmp.iid:400DAC6770A9E011A5CBB499B53F0338, xmp.iid:459BF47772A9E011A5CBB499B53F0338, xmp.iid:469BF47772A9E011A5CBB499B53F0338, xmp.iid:FB568EF74BABE0119234A3B6C088E5DF, xmp.iid:FC568EF74BABE0119234A3B6C088E5DF, xmp.iid:42B07C064DABE0119234A3B6C088E5DF, xmp.iid:43B07C064DABE0119234A3B6C088E5DF, xmp.iid:18AA59B77DB1E011B103CDF67537AA13, xmp.iid:19AA59B77DB1E011B103CDF67537AA13, xmp.iid:43F27DAAEDB6E011A9D3CFB914C45AEC, xmp.iid:A9DD8CEC3EB7E01180809CA13CED36BF, xmp.iid:A665B5EC3EB7E01180809CA13CED36BF, xmp.iid:A765B5EC3EB7E01180809CA13CED36BF, xmp.iid:79EC5E6D3FB7E01180809CA13CED36BF, xmp.iid:1BF0BE873FB7E01180809CA13CED36BF, xmp.iid:1CF0BE873FB7E01180809CA13CED36BF, xmp.iid:05352B81DF20681180838758DEF1C6BD, xmp.iid:06352B81DF20681180838758DEF1C6BD, xmp.iid:07352B81DF20681180838758DEF1C6BD, xmp.iid:7342AC9FDF20681180838758DEF1C6BD, xmp.iid:185B5BA10B2068118083E6923BC4EF12, xmp.iid:195B5BA10B2068118083E6923BC4EF12, xmp.iid:F9260189092068118A6DB380375CCE67, xmp.iid:A11CABA0092068118A6DB380375CCE67, xmp.iid:23BF1996E72068118A6DB0EDB00EDA18, xmp.iid:7FFEE5E7E72068118A6DB0EDB00EDA18, xmp.iid:9AC768D61A2068118A6D863BC2428ECD, xmp.iid:F0732DEC1A2068118A6D863BC2428ECD, xmp.iid:034FA3D29C2168118083E7D55877BD6C History When : 2011:03:10 08:43:19-06:00, 2011:03:10 08:43:19-06:00, 2011:03:10 08:46:41-06:00, 2011:03:10 12:14:17-06:00, 2011:03:10 12:51:42-06:00, 2011:03:10 18:46:34-06:00, 2011:03:10 18:54:04-06:00, 2011:03:10 18:58:05-06:00, 2011:03:10 19:50:52-06:00, 2011:03:10 20:08:07-06:00, 2011:03:10 20:09:21-06:00, 2011:03:10 20:16:36-06:00, 2011:03:10 20:21:04-06:00, 2011:03:10 20:50:12-06:00, 2011:03:10 20:57:09-06:00, 2011:03:10 21:15:55-06:00, 2011:03:10 21:23:46-06:00, 2011:03:10 21:28:04-06:00, 2011:03:10 21:48:44-06:00, 2011:03:15 13:45:48-05:00, 2011:03:15 14:02:56-05:00, 2011:03:15 14:20:54-05:00, 2011:03:15 14:35-05:00, 2011:03:15 14:36:18-05:00, 2011:03:15 14:36:18-05:00, 2011:03:15 14:38:20-05:00, 2011:03:22 13:02:47-05:00, 2011:03:22 13:04:17-05:00, 2011:03:22 13:04:26-05:00, 2011:03:22 13:04:26-05:00, 2011:04:05 10:36:10-05:00, 2011:06:29 14:49:30-05:00, 2011:06:29 14:50:31-05:00, 2011:06:29 14:50:31-05:00, 2011:07:01 14:05:42-05:00, 2011:07:01 14:06:42-05:00, 2011:07:01 14:06:42-05:00, 2011:07:07 10:18:04-05:00, 2011:07:07 10:18:04-05:00, 2011:07:07 13:55:16-05:00, 2011:07:07 13:55:16-05:00, 2011:07:07 14:01:31-05:00, 2011:07:07 14:01:36-05:00, 2011:07:07 14:01:36-05:00, 2011:07:07 14:07:08-05:00, 2011:07:07 14:07:08-05:00, 2011:07:07 14:09:37-05:00, 2011:07:07 14:09:37-05:00, 2011:07:07 22:24:26-05:00, 2011:07:07 22:42:53-05:00, 2011:07:07 22:42:53-05:00, 2011:07:07 22:45:22-05:00, 2011:07:07 22:45:23-05:00, 2011:07:08 01:57:37-05:00, 2011:07:08 01:57:37-05:00, 2011:07:08 02:12:58-05:00, 2011:07:08 03:00:17-05:00, 2011:07:08 09:41:46-05:00, 2011:07:08 09:41:46-05:00, 2011:07:08 09:56:32-05:00, 2011:07:08 09:56:32-05:00, 2011:07:10 18:25:58-05:00, 2011:07:10 18:25:58-05:00, 2011:07:10 18:33:33-05:00, 2011:07:10 18:33:33-05:00, 2011:07:18 15:37:43-05:00, 2011:07:18 15:37:43-05:00, 2011:07:25 13:41:10-05:00, 2011:07:25 23:22:50-05:00, 2011:07:25 23:22:50-05:00, 2011:07:25 23:26:26-05:00, 2011:07:25 23:26:26-05:00, 2011:07:25 23:27:10-05:00, 2011:07:25 23:27:10-05:00, 2011:09:08 12:26:29-05:00, 2011:09:08 12:26:29-05:00, 2011:09:08 12:27:20-05:00, 2011:09:08 12:27:20-05:00, 2011:12:20 17:45:46-06:00, 2011:12:20 17:45:46-06:00, 2012:03:02 09:18:38-05:00, 2012:03:02 09:19:18-05:00, 2012:04:05 13:20:51-04:00, 2012:04:05 13:23:09-04:00, 2012:06:19 16:31:18-04:00, 2012:06:19 16:31:18-04:00, 2012:06:19 16:15:01-05:00 History Software Agent : Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5 History Changed : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /metadata, /, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata Metadata Date : 2014:12:19 16:30:55-06:00 Creator Tool : Adobe InDesign CS5.5 (7.5) Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 7894 bytes, use -b option to extract), (Binary data 3836 bytes, use -b option to extract) Format : application/pdf Title : DJO Foundation Total Knee Surgical Technique Creator : DJO Surgical Rights : Copyright 2011 Encore Medical, LP Doc Change Count : 35 Producer : Adobe PDF Library 9.9 Trapped : False Creator Address : 9800 Metric Blvd. Creator City : Austin Creator Region : Texas Creator Postal Code : 78758 Creator Country : USA Creator Work Telephone : 800 456-8696 Creator Work URL : www.djosurgical.com Page Count : 14EXIF Metadata provided by EXIF.tools