MPS3000+ User Guide MPS3000 INSTRUCTION MANUAL 08 06 2009

2016-06-06

• 1. Table of Contents
• 2. Introduction
  • 2.1. Protection Features
  • 2.2. Control Features
  • 2.3. Supervision and Communication Features
• 3. Wiring Diagrams
  • 3.1. Wiring Diagram – MPS3000
  • 3.2. Wiring Diagram – MPS3000-C
• Rear Panel – MPS 3000 and MPS 3000-C
• MPS 3000 Terminals
  • 5.1. Auxiliary Power Supply
  • 5.2. Current & Voltage & Temperature (RTD, Thermistor) Inputs
  • 5.3. Line Voltages
  • 5.4. Line Currents
  • 5.5. Ground Fault Current
  • 5.6. Temperature Sensors
  • 5.7. Analog Outputs
  • 5.8. Analog Inputs
  • 5.9. MPS3000-C Discrete Inputs
  • 5.10. Output Relays
  • 5.11. Serial Link
• 6. C/Ts Wiring Diagrams
  • 6.1. Three C/Ts + Ground Fault Core Balance C/T
  • 6.2. Three C/T's in a Residual Ground Fault Connection
• 7. Front Panel Overview and Settings
  • 7.1. Front Panel Settings
    • 7.1.1. Startup
    • 7.1.2. Reset to Factory Default Values
  • 7.2. Messages
    • Blinking Messages
    • Solid Messages
  • 7.3. Menu Navigation Top
    • 7.3.1. SYSTEM PARAMETER SETTINGS
    • 7.3.2. MEASURED DATA
    • 7.3.3. TEST / MAINTENANCE
• 8. Set Pages and Default Parameters
• 9. PARAMETERS SETTINGS PAGES
  • 9.1. SYSTEM PARAMETER SETTINGS
  • 9.2. VOLTAGE SETTINGS
  • 9.3. CURRENT SETTINGS
  • 9.4. OVERLOAD SETTINGS
  • 9.5. POWER SETTINGS
  • 9.6. TEMPERATURE SETTINGS
  • 9.7. ANALOG I/O SETTINGS
  • 9.8. COMMUNICATION P. SETTINGS
  • 9.9. TRIPPING/ALARM OPTIONS
    • 9.9.1. Tripping Alarm Common Settings
    • 9.9.2. Multiple Alarm/Trip Considerations
    • 9.9.3. Tripping/Alarm Individual Settings
      • 9.9.3.1. MAX START TIME
      • 9.9.3.2. TOO MANY STARTS
      • 9.9.3.3. UNDER CURRENT LEVEL 1
      • 9.9.3.4. UNDER CURRENT LEVEL 2
      • 9.9.3.5. LOAD INCREASE
      • 9.9.3.6. OVER CURRENT LEVEL 1- JAM
      • 9.9.3.7. OVER CURRENT LEVEL 2 - SHORT
      • 9.9.3.8. THERMAL LEVEL 1 and 2
        • THERMAL LEVEL 1
        • THERMAL CAPACITY RESET METHOD
      • 9.9.3.9. UNBALANCE LEVEL 1
      • 9.9.3.10. UNBALANCE LEVEL 2
      • 9.9.3.11. Setting U/B LEVEL 2 MAX T
      • 9.9.3.12. U/V LEVEL (Undervoltage Level)
      • 9.9.3.13. O/V LEVEL 1 (Over Voltage Level 1)
      • 9.9.3.14. O/V LEVEL 2 (Over Voltage Level 2)
      • 9.9.3.15. PHASE LOSS
      • 9.9.3.16. PHASE SEQUENCE
      • 9.9.3.17. GND FAULT LEVEL 1 (Ground Fault Level 1)
      • 9.9.3.18. GND FAULT LEVEL 2 (Ground Fault Level 2)
      • 9.9.3.19. COMM. PORT FAILED (Communication Port Failed)
      • 9.9.3.20. INTERNAL FAILURE
      • 9.9.3.21. CONTROL CIR. OPEN & WELDED CONTACTOR (Control Circuit Open & Welded Contactor)
      • 9.9.3.22. EXTERNAL FAULT 1 / 2 / 3
      • 9.9.3.23. RTD 1-10, LEVEL 1-2 (Temperature 1.. 10 Level 1.. 2)
      • 9.9.3.24. UNDER PWR LVL 1 (Under Power Level 1)
      • 9.9.3.25. UNDER PWR LVL 2 (Under Power Level 2)
      • 9.9.3.26. LOW POWER FACTOR
      • 9.9.3.27. ANALOG INPUTS FAULTS
    • 9.9.4. Tripping/Alarm Default Settings
      • 9.9.4.1. Added Options Available in the MPS3000 Which Correspond to ANSI Codes
• 10. DATA PAGES - MENUS
  • 10.1. MEASURED DATA
  • 10.2. CALCULATED DATA
    • THERMAL CAPACITY
    • TIME TO TRIP-O/L
    • NO TRIP EXPECTED
    • TIME TO START
  • 10.3. LOGICAL INPUTS CONTACT STATUS
  • 10.4. STATISTICAL DATA
    • TOTAL RUN TIME
  • 10.5. FAULT DATA
• 11. Test / Maintenance Options
• 12. Communication – Serial Link
• 13. Technical Specifications
• 14. Case and Cutout Details
• 15. Appendix A - Changes From MPC 2000 to MPS 3000
• 16. Appendix B – Parameters List and Factory Default Settings
• 17. Appendix C – Ordering Information