NCB® Distal Femur System Surgical Technique NCB Femoral

2016-04-01

: Pdf Ncb Distal Femoral Surgical Technique NCB_Distal_Femoral_Surgical_Technique 4 2016 pdf

Open the PDF directly: View PDF .
Page Count: 36

Download
Open PDF In Browser	View PDF

NCB® Distal
Femur System

Surgical Technique

NCB® Distal Femur System – Surgical Technique

Surgical Technique
NCB Distal Femur System

Table of Contents
Introduction

Indications 8
Preoperative Planning

Contraindications 8
Patient Positioning

Sample Cases

Open Technique
Incision 11
Reposition 11
Optional: Bone Spacers

Insertion of the NCB Plate

Insertion of the NCB Screws

Tips and Tricks

MIS Technique*
Incision 17
Aiming Arm Assembly for Insertion

Insertion of the NCB Plate

Reduction of the Metaphyseal Bone Part

Insertion of the NCB Screws in the Shaft Part

Implant Removal

Ordering Information
Implants 24

*MIS Minimally Invasive Solutions™ Technique by Zimmer

Graphic Case

Standard Instruments

MIS Instruments

Planning Aid

NCB® Distal Femur System – Surgical Technique

Introduction
The NCB DF System (Non-Contact
Bridging for the Distal Femur) Plate is
an optimal solution for the treatment of
complex fractures at the distal femur.
The system allows for polyaxial screw
placement with subsequent screw
locking for improved stability especially
within osteopenic bone. Before locking,
the screws can act as lag screws and
be used for fracture reduction; a benefit
which is not offered with standard
locking systems.

Implants sizes (5–9–13 holes)
and types (left/right)

In the locked mode NCB DF Plate acts
as an internal fixator without contact
between the plate and the bone surface
reducing the risk of periosteal blood
supply impairment.
The surgical technique is based on the
well-known standard plate osteosynthesis technique and in a last step
all screws can be locked and be made
angular stable. The instrumentation
includes a fully radiolucent targeting
device for a minimal-invasive surgical
technique (MIS).

Non
Contact

Polyaxial screw placement with
subsequent locking option for
optimal system stability. Possible
fracture reduction with a lag screw

Non-Contact Bridging
ostesynthesis reduces the
risk of periosteal blood
impairment

Spacer 1 to 3 mm

Anatomically contoured
plate. Forged titanium
alloy for better mechanical
strength

Blind screw

Locking cap  8 mm
N (Newton)

(SD±10N)

225
6 Nm
F
Fastening torque

Angular stability of one NCB
Locked Screw
Materials: NCB Plates and Screws are made
of Ti6Al4V, ISO 5832-3, ASTM F136; the 3.5 mm
cortical screw self tapping is made of Ti6Al7Nb,
ISO 5832-11, ASTM F1295.

Self-tapping screws:
Double lead thread for fast screw insertion
in cortical bone.
 5.0 mm NCB cortical screws L= 14–100 mm
 5.0 mm NCB cancellous screws L= 50–100 mm
 5.0 mm NCB MotionLoc® screws L= 30–60 mm
 3.5 mm cortical screw L= 50–85 mm

NCB® Distal Femur System
– Surgical
– Surgical
Technique
Technique

Cable Fixation Options
The following products from the Zimmer®
Cable-Ready® Cable Grip
System are compatible with the NCB
Distal Femur System:
See data sheet REF 97-2232-015-00 for
more specific instructions.

NCB Locking Plate
Cable Button, 2.5mm, Hex Drive

Hex Button, 3.5mm

Cable Assembly Cerclage,
1.8mm

• Sterile
• Material: Ti6Al4V

• Sterile
• Material: C.P. Titanium

• Sterile
• Material: CoCr

REF 47-2232-060-00 Color: Gold*
REF 47-2232-060-01 Color: Blue

REF 00-2232-002-35

REF 00-2232-002-28
REF 00-2232-004-18

Application
This Cable Button is threaded
directly into the NCB Plate hole to
provide a positioning point for
the Cable.
Instructions
To insert, use the 2.5mm hex
screwdriver to thread the cable
button into the plate hole. Do not
fully tighten to allow the slots in
the button to align with the cable.
To remove, use the 2.5mm hex
screwdriver to unthread the cable
button from the plate hole.

Cable Fixation Options

* Not available in Europe, Middle East and Africa.

Application
This Hex Button fits into the
standard hex in the screw head
(3.5mm hex). Therefore, it can
be inserted into the NCB Screw
head, or into the NCB Locking
Cap.

Note: The Hex button is incompatible with the 2.5mm Hex of
the Cortical self-tapping screws
(REF 02.03131.0xx)

Cable Fixation with
Cable Button

Cable Fixation with
Hex Button

NCB
NCB®®Distal
DistalFemur
Femur–System
Surgical
– Surgical
Technique
Technique

MIS Radiolucent Targeting
Device
MIS* operation technique with a fully
radiolucent targeting device.

Targeting device and plate assembly

*MIS Minimally Invasive Solutions Technique by Zimmer

NCB® Distal Femur System
– Surgical
– Surgical
Technique
Technique

Divergent Screw Alignment
The targeting device ensures divergent
screw alignment for increased pull-out
resistance in the metaphysial and
diaphysial region.

Divergent screws alingnment achieved using
the targeting device

NCB
NCB®®Distal
DistalFemur
Femur–System
Surgical
– Surgical
Technique
Technique

Indications
The NCB Polyaxial Locking Plate System is
indicated for temporary internal fixation
and stabilization of fractures and osteotomies of long bones.
Note: The NCB Distal Femur Plate from
the NCB Polyaxial Locking Plate System is
specifically designed for the distal femur.

Preoperative Planning
Prior to surgery, it is recommended to
conduct preoperative planning using the
X ray template (REF 06.01240.000).

Contraindications
• All concomitant diseases that may
impair the fixation of the implant and/
or the success of the intervention.
• Lack of bone substance or poor bone
quality which makes stable seating
of the implant impossible.
• Acute or chronic, local or systemic
infections.
• Allergy to the implanted material.
• Severe muscular, neural or
vascular diseases that endanger
the extremities involved.

Patient Positioning
Lay the patient in supine position on a
radiolucent table. Support the knee, but
allow the leg to move freely. Make sure
that a true lateral X ray of the femur can
be obtained in this position. Avoid strong
traction and a completely extended
knee because forces of the gastrocnemius
muscle will generate hyperextension of
the distal fragment.
To lessen the forces of the gastrocnemius,
flex the leg approximately 20–40°.

X ray template

REF

06.01240.000

NCB® Distal Femur System
– Surgical
– Surgical
Technique
Technique

Sample Cases
Case 1: Extra-articular fracture

AP view preoperative

AP view postoperative

Lateral view showing ‘non contact’
of the plate

Lateral view postoperative

NCB
NCB®®Distal
DistalFemur
Femur–System
Surgical
– Surgical
Technique
Technique

Case 2: Intra-articular fracture

Lateral view preoperative

AP view preoperative

Lateral view postoperative

AP view postoperative

NCB® Distal Femur System – Surgical Technique

Open Technique
Incision
A lateral incision is recommended. The
skin incision starts at Gerdy’s tubercle and
goes on in a proximal direction to expose
the fracture zone. The muscles are left
attached to the fracture fragments
for optimal blood supply. Do not strip
the periosteum.
Incision

Reposition
For intra-articular fracture an arthrotomy
is performed to anatomically reduce the
joint line.
Temporarily fix the bone fragments with
2.0 mm K-wires (REF 290.20.280). Make
sure that the K-wires do not interfere with
the location of the plate.

Temporary stabilization of the fracture

NCB® Distal Femur System – Surgical Technique

Optional:
Bone Spacers
Two bone spacers should be used
in the diaphysis to avoid the contact
of the plate with the bone surface
reducing the risk of periosteal blood
supply impairment. The spacers
are available in sizes of 1 mm, 2 mm
or 3 mm (REF 02.03150.311 to .313).
The blue 2 mm spacer is usually used.
Insert the adequate bone spacers
into the plate before plate insertion.
Note: The bone spacers are single use
only. The spacers can be removed after
locking of the screws.

3 mm

2 mm

1 mm

Bone spacers for non contact bridging

Insertion of the NCB Plate
Insert the plate between the vastus
lateralis muscle and the periosteum.
Keep the proximal end in continous
contact with the bone surface during
insertion. Place the distal end of the
plate against the lateral condyle.
Note: The plate is anatomically shaped
and does reach far distally close to the
cartilage – bone interface.

Temporarily fix the plate with 2.0 mm
K-wires (REF 290.20.280) at both ends
of the plate.

Temporary plate fixation

NCB® Distal Femur System – Surgical Technique

Insertion of the NCB Screws
Three screw types are offered with the NCB
System. Cancellous screws preferably for the
epi- and metaphysis as well as cortical bone
screws which are optimal for placement in the
diaphysis. Surgical technique (REF 97-3161002-00 or 97-3161-004-00)* has specific
instructions for the NCB MotionLoc Screw.

Cancellous Screws
1. For cancellous screws place the NCB Drill
Guide 2.5 mm (REF 02.00024.010) into the
plate hole and point into the direction of the
screw axis.

Use the NCB drill guide to avoid
an angular inclination > 30°

Note: Press the drill guide into the plate hole
in a perpendicular start position and tilt it
into the needed direction. The drill guide
needs to be in constant contact with the
bottom ring of the hole. The guide limits the
possible angular range of 30° for placing a
locked NCB Screw. Always use the drill guide
since it prevents to choose an excessive screw
angle and failure of subsequent locking.
2. Drill with the 2.5 mm drill bit
(REF 103.25.180). In case of good bone
quality it is recommended to drill the cortex
with a 4.3 mm drill bit. Take away the drill
sleeve for this purpose.

Drilling

Optionally the 95° guide
(REF 02.00024.234/02.00024.235) can
be used for distal screw placement.
Note: Right and left versions are available.
The 95° guide is fixed to the plate using the
DF plate connection bolt for the targeting
device (REF 02.00024.073). Place the appropriate NCB Drill Guide through one of the
holes of the 95° guide and into the plate
hole. Drill with the corresponding 2.5 mm or
4.3 mm drill bit. Repeat for the other hole in
the 95° guide.
3. The appropriate screw length is
determined with the NCB Depth Gauge
(REF 02.00024.005)

* 97-3161-002-00 is for countries where NCB MotionLoc screws are approved to be used with only
NCB plates and 97-3161-004-00 is for countries where NCB MotionLoc screws are approved to
be used with both NCB as well as NCB Periprosthetic plates. See NCB MotionLoc package insert
for approved plate/MotionLoc screw combinations.

Determine the screw length

NCB® Distal Femur System – Surgical Technique

4. Insert the NCB Cancellous Screws
using the NCB Screwdriver, (REF
02.00024.023) and apply compression.
Cancellous screws are partially threaded
and can be used for compression.
In the epiphyseal and metaphyseal area
screws should be tightened to reduce
the fracture and to obtain close contact
between the plate and the bone in order
to buttress the fracture.
5. Remove the K-wire after screw insertion.

Use the NCB Screw Driver to tighten the screw and apply compression

6. To lock the screw insert the locking
cap (REF 02.03150.300) and tighten the
cap with the NCB Torque Screwdriver,
6Nm (REF 02.00024.021) until a clicking
sound is heard.
Note: Always use the torque screwdriver
to tighten the locking caps and make
sure not to tilt the screwdriver during its
usage.
Not to do so could damage the hex
drive of the cap and might complicate
later extraction of the implant.

Insert the locking cap

NCB® Distal Femur System – Surgical Technique

Cortical Screws
1. If an NCB cortical screw is used, use
the NCB Drill Guide (REF 02.00024.011)
and drill with the drill bit 4.3 mm
(REF 02.00024.002). Drill through both
cortices. In the case of hard cortical
bone, tap the cortex with the tapper
(REF 02.00024.050).

Drilling

2. Insert the NCB Screw using the
NCB Screwdriver, (REF 02.00024.023).
3. To lock the screw proceed as for the
cancellous screws: insert the locking cap
(REF 02.03150.300) and tighten the cap
with the NCB Torque Screwdriver, 6Nm
(REF 02.00024.021) until a clicking sound
is heard.
4. In the diaphyseal area bone spacers
are used to prevent close contact. After
locking of the screws the spacers should
be removed.

Insert the cortical screw

For the placement of the additional
screws proceed as above.

Final plate fixation (example)

NCB® Distal Femur System – Surgical Technique

Tips and Tricks
The polyaxiality of the system allows
some varus/valgus correction during
surgery.
For this purpose insert four screws as
shown in the figure without tightening
the screws. Place the two distal screws
anterior and posterior.
Now the fracture can be reduced by
rotation around the bone axis of the
proximal fragment and varus/valgus
correction of the distal fragment.
Confirm satisfying alignment with the
image intensifier and lock the screws
using the locking caps.
Afterwards complete the
osteosynthesis by adding additional
screws where needed.
When inserting locking caps, turn the
screw driver counter clockwise initially.
The threads of the cap and the plate
will “click”, indicating that the cap is
properly aligned and less likely to crossthread when turned clockwise.

Varus/valgus corrections

NCB® Distal Femur System – Surgical Technique

MIS Technique*
Incision
A lateral incision is recommended if a
simple articular or extra-articular fracture
is current. The skin incision starts at
Gerdy’s tubercle and extends approximately 80 mm in a proximal direction.
The muscles are left attached to the
fracture fragments for optimal blood
supply. Do not strip the periosteum. For
intra-articular fracture an arthrotomy
is performed to anatomically reduce the
joint line.
Before insertion of the plate anatomically
reduce the intra-articular fracture and
fix it with a 3.5 mm cortical screw
or a 2.0 mm K-wire. Make sure they
do not interfere with the position of
the plate and locking screws. Predrill
3.5mm cortical screw with 2.5mm
drill bit (103.25.180) using screwdriver
(109.01.020).

Incision

Temporary stabilization of the fracture

Targeting Device Assembly
for Insertion
Attach the NCB DF Targeting Device
left (REF 02.00024.071) for a left NCB
Plate and the right targeting device
(REF 02.00024.070) for a right
plate. Screw the two connection bolts
(REF 02.00024.073) into the NCB
Plate and tighten them with the hex
screwdriver.
Insert the connection bolt

Insertion of the NCB Plate
1. Insert the plate between the vastus
lateralis muscle and periosteum.
Keep the proximal end of the plate in
close contact with the bone during
insertion. Place the distal end of the
plate onto the lateral condyle.

Insert the plate

*MIS Minimally Invasive Solutions Technique by Zimmer

NCB® Distal Femur System – Surgical Technique

2. Make a stab incision at the most
proximal plate hole. Screw the NCB
Stabilization Bolt (REF 02.00024.074)
into the NCB Plate.

Insert the stabilization bolt

3. Adjust the correct distance between
the targeting device and the plate by
pushing the targeting device along the
stabilization bolt and securing the
correct distance with the NCB Safety
Lock Pin (REF 02.00024.076). The safety
locking pin needs to be inserted from
the anterior side.

Insert the NCB Safety Locking Pin from the anterior
side

Reduction of the Metaphyseal
Bone Part
1. Insert a 2.0 mm Kirschner wire
(REF 290.20.280) through the distal end
of the plate for temporary reposition
of the condyles.

Temporary reposition of the condyles

NCB® Distal Femur System – Surgical Technique

2. For placing a NCB Cancellous
Screw drill with the 2.5 mm drill bit
(REF 103.25.180) and the NCB Drill
Guide (REF 02.00024.010).

Use the NCB Drill Guide

3. Insert an NCB Cancellous Screw and
apply compression if needed.

Insert cancellous screw

4. Repeat drilling and insert a second
NCB Cancellous Screw. Repeat the
procedure if more screws are required,
then lock the screws with locking caps
(REF 02.03150.300).
Then adjust length and rotation under
image intensifier and insert the proximal K-wire.

Insert additional cancellous screw

Note: Only the most distal screws can
be locked if the targeting device is on.
The other screws in the joint area need
to be locked when the targeting device
is off at the end of the operation.

NCB® Distal Femur System – Surgical Technique

Insertion of the NCB Screws in
the Shaft Part
Start with placing a proximal screw close
to the fracture site.
1. Make a stab incision to access the
plate hole. Insert the NCB Trocar, drill
guide and protection sleeve assembly
(REF 02.00024.060 to .062).

Insert tissue protection sleeves

2. Screw the drill guide into
the plate hole.

Screw the drill guide into the plate

3. Screw the protection sleeve into
the targeting device. The sleeve will be
in direct contact with the plate.

Screw the protection sleeve into the targeting device

NCB® Distal Femur System – Surgical Technique

4. Remove the trocar and drill using
the 4.3 mm drill bit (REF 02.00024.003 )
for the 5 mm NCB Screw.
The scaling on the drill bit can be used
to determine the screw length.

Drill the screw hole

5. Alternatively, determine the screw
length using the NCB Depth Gauge
(REF 02.00024.006).

Mesure the screw length

6. Remove the drill guide and
insert the appropriate screw using
the NCB Hexagonal Screwdriver
(REF 02.00024.023). The screw can
be used for repositioning of a fragment.

Insert the screw into the bone shaft

NCB® Distal Femur System – Surgical Technique

7. For locking of the screw insert the
locking cap (REF 02.03150.300) and
tighten the cap with the NCB Torque
Screwdriver, 6Nm (REF 02.00024.021)
until a clicking sound is heard.
Note: Always use the torque screwdriver
to tighten the locking cap and make
sure not to tilt the screwdriver during its
usage.
Not to do so could damage the hex
drive of the screw and might complicate
later extraction of the implant.

Insert the locking cap on top of the screw

8. Repeat step 1 to 7 to insert additional
screws.

Insert additional screws

9. To place a screw at the most proximal
end exchange the NCB Stabilization
Bolt with the NCB Trocar, drill guide and
protection sleeve assembly. Drill using
the 4.3 mm drill bit (REF 02.00024.003)
for the 5mm NCB Screw and lock
the screw with the NCB Locking Cap
as described above.

Exchange the stabilization bolt with the protection
sleeve assembly

NCB® Distal Femur System – Surgical Technique

10. Remove the aiming arm if additional screws need to be placed at the position where the aiming arm is attached.
Insert the screws as described in the
open technique (page 15).

Place additional NCB Cancellous Screws
in the joint area if needed.

Final plate fixation (example)

Implant Removal
To remove the NCB DF Plate, first remove
all locking caps. Then loosen all the
NCB Bone Screws without completely
removing them (this prevents rotation
of the bone plate when removing
the last screw). After that completely
remove all bone screws.

NCB® Distal Femur System – Surgical Technique

Ordering Information
Implants***

Quantity*

 mm

3.9

NCB® Locking Cap
Ti6Al4V

M 8 x 0.75

REF

15 8 3.5 02.03150.300

NCB® Blind Screw
Ti6Al4V
5.7

5.7

Quantity*

Femur Plate, left
Ti6Al4V

NCB®

Quantity* Holes mm REF

1
1
1

5
9
13

167 02.03260.105
246 02.03260.109
324 02.03260.113

Femur Plate, right
Ti6Al4V
5
9
13

167 02.03260.005
246 02.03260.009
324 02.03260.013

NCB® Spacer
(red, blue, green)
Ti6Al4V

4.2

31.6

NCB®

mm REF

31.6

 mm

5 8 3.5 02.03150.310

M 8 x 0.75

Quantity* L mm

2
2
2

Color

REF

1 3.5 red 02.03150.311
2 3.5 blue 02.03150.312
3 3.5 green 02.03150.313

Materials: NCB Plates and Screws are made of
Ti6Al4V, ISO 5832-3, ASTM F136; the cortical
screw self tapping is made of Ti6Al7Nb,
ISO 5832-11, ASTM F1295.

* Indicates the quantity in the standard graphic case.
*** Sterile products are also available. For a complete list of available sterile products, please contact your sales representative.

NCB® Distal Femur System – Surgical Technique

NCB® Screw, self-tapping
Ti6Al4V
4.4

NCB® Cancellous Screw, 32mm
Ti6Al4V
5

4.2

5

6.2

Cortical Screw, self-tapping
Ti6Al7Nb
3.5

2.5

6.2

6

2.9
1.75
L

Quantity* L mm  mm

REF

Quantity* L mm  mm

14
16
18
20

5.0
5.0
5.0
5.0

3.5
3.5
3.5
3.5

02.03150.014
02.03150.016
02.03150.018
02.03150.020

2
2
2
2
2
2
2
2
2
2
2
2
2
2
–
–

22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
55

5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0

3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5

02.03150.022
02.03150.024
02.03150.026
02.03150.028
02.03150.030
02.03150.032
02.03150.034
02.03150.036
02.03150.038
02.03150.040
02.03150.042
02.03150.044
02.03150.046
02.03150.048
02.03150.050
02.03150.055

2
2
2
2
2
2
2
2
–
–
–

–
–
–
–
–
–
–
–
–

60
65
70
75
80
85
90
95
100

5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0

3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5

02.03150.060
02.03150.065
02.03150.070
02.03150.075
02.03150.080
02.03150.085
02.02150.090**
02.02150.095**
02.02150.100**

Indicates the quantity in the standard graphic case.
Available sterile only

2
2
2
2

*
**

1.25

1.75

50
55
60
65
70
75
80
85
90
95
100

5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0

3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5

REF

Quantity* L mm  mm

02.03152.050
02.03152.055
02.03152.060
02.03152.065
02.03152.070
02.03152.075
02.03152.080
02.03152.085
02.02152.090**
02.02152.095**
02.02152.100**

1
1
1
1
1
1
1
1

50
55
60
65
70
75
80
85

3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5

2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5

REF

02.03131.050
02.03131.055
02.03131.060
02.03131.065
02.03131.070
02.03131.075
02.03131.080
02.03131.085

NCB® Distal Femur – Surgical Technique

NCB® MotionLoc® Screws, self-tapping
5.0 mm Cortical, Ti6Al4V, Non Sterile
See surgical technique (REF 97-3161-002-00 or 97-3161-004-00)** for more specific instructions.
Item Number

 mm

L mm

02.03161.030 5.0 30 3.5
02.03161.032 5.0 32 3.5
02.03161.034 5.0 34 3.5
02.03161.036 5.0 36 3.5
02.03161.038 5.0 38 3.5
02.03161.040 5.0 40 3.5
02.03161.042 5.0 42 3.5
02.03161.044 5.0 44 3.5
02.03161.046 5.0 46 3.5
02.03161.048 5.0 48 3.5
02.03161.050 5.0 50 3.5
02.03161.052 5.0 52 3.5
02.03161.054 5.0 54 3.5
02.03161.056 5.0 56 3.5
02.03161.058 5.0 58 3.5
02.03161.060 5.0 60 3.5

Compatible Zimmer Products with the NCB Distal Femur System
See data sheet REF 97-2232-015-00 for more specific instructions.
REF sterile

Description

47-2232-060-00*
47-2232-060-01
00-2232-002-35
00-2232-002-28
00-2232-004-18

NCB Polyaxial Locking Plate Cable Button, Gold, 2.5mm Hex Drive, Material: Ti6Al4V
NCB Polyaxial Locking Plate Cable Button, Blue, 2.5mm Hex Drive, Material: Ti6Al4V
Hex Buttons, 3.5mm Hex, Material: C.P. Titanium
Cable-Ready Cable Assembly Cerclage, ∅ 1.8mm, L. 914mm, Material: CoCr
Cable-Ready Cable Assembly Cerclage, ∅ 1.8mm, L. 635mm, Material: CoCr

* Not available in Europe, Middle East and Africa.
** 9
7-3161-002-00 is for countries where NCB MotionLoc screws are approved to be used with only NCB
plates and 97-3161-004-00 is for countries where NCB MotionLoc screws are approved to be used with
both NCB as well as NCB Periprosthetic plates. See NCB MotionLoc package insert for approved plate/
MotionLoc screw combinations.

NCB® Distal Femur System
– Surgical
– Surgical
Technique
Technique

Graphic Case

NCB® DF Plate standard graphic case
for open technique (with content)

REF

ZS02.00024.600

NCB® Graphic Case for Femur
(empty)
REF

02.00024.610

NCB® DF Plate graphic case
modul instruments

NCB® DF Plate graphic case
modul screw rack

REF

02.00024.603

02.00024.605

NCB® DF Plate graphic case, lid

REF
02.00024.601

NCB® DF Plate graphic case
modul implants
REF

02.00024.604

NCB® DF Plate graphic case, base (inox)

REF
02.00024.602

NCB
NCB®®Distal
DistalFemur
Femur–System
Surgical
– Surgical
Technique
Technique

Standard Instruments

NCB® Drill Bit, with quick coupling

NCB® Torque Screwdriver, 6 Nm

Screw forceps self-holding

Quantity*

Quantity* REF

L mm

 REF

L mm

 REF

– 145
4.3 02.00024.001
1 195
4.3 02.00024.002

1 280
3.5 02.00024.021

NCB® Measuring Device

NCB® Tap for quick coupling

Depth gauge small for screws

Quantity* L mm  REF

Quantity*

Quantity* L mm

1 110
5.0/4.5/4.0 02.00024.005

1 145
5.0 02.00024.050

1 110
3.5/4.0 100.90.025

NCB® Drill Guide

T-handle, with quick coupling
1 100.90.210

L mm

 REF

Quantity*

 REF

NCB® Locking Screw Holder for 3.5
hexagonal screwdriver

2.5 02.00024.010

Quantity*

L mm

 REF

100.90.005

 REF

Quantity* REF

— 95 5.0 02.00024.121

L
l

Double drill guide

Two-flut. drill bit, with quick coupling

NCB® Drill Guide

Quantity*

 REF

Quantity*

L mm

Quantity*

 REF

2.5/3.5/4.0 100.40.035

180 154 2.5 103.25.180

4.3 02.00024.011

*Indicates the quantity in the standard graphic case.

 REF

NCB® Distal Femur System
– Surgical
– Surgical
Technique
Technique

Tap for quick coupling

Kirschner wire, Stainless Steel

Quantity*

L mm

 REF

L mm

 REF

1 110
3.5 106.35.110

5 280
2.0

Countersink, for quick coupling
Quantity*

REF
— 3.5/4.0 108.01.035

95° Drill Guide

Small hexagonal screwdriver without
holding sleeve, hexagonal 2.5 mm
Quantity* REF

109.01.020

Holding sleeve for small hexagonal
screwdrivers
Quantity* REF

109.01.060

*Indicates the quantity in the standard graphic case.

290.20.280

Quantity* REF

—
—

Right 02.00024.234
Left 02.00024.235

NCB
NCB®®Distal
DistalFemur
Femur–System
Surgical
– Surgical
Technique
Technique

MIS Instruments

Assembly pin
Quantity** REF

NCB® DF Plate graphic case module MIS
instruments, includes additional
instruments for the MIS technique
(with content)
Quantity**

REF

ZS02.00024.650

02.00002.001

NCB® DF Plate Drill Bit 4.3
Quantity**

L mm

REF

1 300 02.00024.003

NCB® DF Plate graphic case module MIS
instruments (no content)
Quantity** REF

02.00024.606
NCB® DF Plate Measuring Device
Quantity** REF

02.00024.006

NCB® DF Plate Hexagonal Screwdriver for
femur SW 3.5
Quantity**

L mm

REF

1 275 02.00024.023

NCB® DF Plate Hexagonal Screwdriver
Shaft SW 3.5
Quantity**

L mm

REF

1 180 02.00024.024

**Indicates the quantity in the MIS graphic case module.

NCB® Distal Femur System
– Surgical
– Surgical
Technique
Technique

NCB® DF Plate Taps for quick coupling

NCB® DF Plate Targeting Device for plates

Quantity** L mm

Quantity** Side

 REF

REF

1 250
5.0 02.00024.051

1
1

NCB® DF Plate Soft Tissue Protection
Sleeve

NCB® DF Plate Connection Bolt for
targeting device

Quantity**

 REF

Quantity**

L mm

10.0/8.2 02.00024.060

144 02.00024.073

NCB® DF Plate Drill Guide

right
02.00024.070
left 02.00024.071

REF

Quantity**

 REF

NCB® DF Stabilization Bolt
for targeting device

8.2/4.3 02.00024.061

Quantity**

L mm

153 02.00024.074

REF

Quantity**

 REF

NCB® Safety Lock Pin for targeting
device for femur

4.3 02.00024.062

Quantity** REF

NCB® DF Plate Trocar

**Indicates the quantity in the MIS graphic case module.

02.00024.076

NCB
NCB®®Distal
DistalFemur
Femur–System
Surgical
– Surgical
Technique
Technique

Planning Aid

X ray template

REF

06.01240.000

NCB® Distal Femur – Surgical Technique

Notes

NCB
NCB®®Distal
DistalFemur
Femur–System
Surgical
– Surgical
Technique
Technique

Notes

This documentation is intended exclusively for physicians and is not intended for laypersons.
Information on the products and procedures contained in this document is of a general nature and does not represent
and does not constitute medical advice or recommendations. Because this information does not purport to constitute
any diagnostic or therapeutic statement with regard to any individual medical case, each patient must be examined and
advised individually, and this document does not replace the need for such examination and/or advice in whole or in part.
Please refer to the package inserts for important product information, including, but not limited to, contraindications,
warnings, precautions, and adverse effects.

Contact your Zimmer representative or visit us at www.zimmer.com

Lit.No. 06.01221.012 – Ed. 2015-08

Disclaimer

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2015:09:23 12:06:42-05:00
Creator                         : Adobe InDesign CS6 (Macintosh)
Modify Date                     : 2015:12:02 10:17:05-05:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Modified                        : 2015:09:29 06:37:02.454-05:00
Subject                         : null
Title                           : NCB® Distal Femur System Surgical Technique
Size                            : 3116036
Sha 1                           : cd6a38968cd6e96f7b6ffcacbbd6182d287f5013
Extracted                       : 2015:09:28 19:22:47.658-05:00
Metadata Date                   : 2015:12:02 10:17:05-05:00
Creator Tool                    : Adobe InDesign CS6 (Macintosh)
Rendition Class                 : proof:pdf
Original Document ID            : xmp.did:94CF50E51F206811871FF144B1C9F8DC
Instance ID                     : uuid:6670ff66-6cf9-e74d-b23a-0232d07cd023
Document ID                     : xmp.id:814A58C40D2068118083C2E6802626AF
Derived From Rendition Class    : default
Derived From Instance ID        : xmp.iid:7F4A58C40D2068118083C2E6802626AF
Derived From Document ID        : xmp.did:F023D0750A206811AB0895D5261C7886
Derived From Original Document ID: xmp.did:94CF50E51F206811871FF144B1C9F8DC
History Action                  : converted
History Software Agent          : Adobe InDesign CS6 (Macintosh)
History Parameters              : from application/x-indesign to application/pdf
History When                    : 2015:09:23 12:06:42.000-05:00
History Changed                 : /
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Layout                     : TwoPageRight
Page Count                      : 36

EXIF Metadata provided by EXIF.tools

NCB® Distal Femur System Surgical Technique NCB Femoral

Navigation menu

Versions of this User Manual:

Views

Navigation