Over Dryve 8 Pro User Manual 7 EN

User Manual: Pdf OverDryve 8 Pro - User Manual User Guide for Rand McNally GPS, Free Instruction Manual

Open the PDF directly: View PDF .
Page Count: 60

Download
Open PDF In Browser	View PDF

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Statement

This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement

This device complies with FCC SAR exposure limits set forth for an uncontrolled
environment.

SAR compliance for using the equipment in close proximity to the human body has
been evaluated at 0mm.
This equipment must not be co-located or operating in conjunction with any other
antenna or transmitter.

Caution!

Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Canada Statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
(1) l’appareil ne doit pas produire de brouillage;

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.
This equipment should be installed and operated with a minimum distance of 0mm
between the radiator and your body.
Cet équipement devrait être installé et actionné avec une distance minimum de
0mm entre le radiateur et votre corps.

This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps
qu'aucune autre antenne ou émetteur.

The device for operation in the band 5150–5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite systems.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés
uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.

End-users and installers must be provide with antenna installation instructions and
consider removing the no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that
may cause undesired operation.

OverDryve™ Pro User Manual

About GPS
The Global Positioning System (GPS) is a constellation of satellites that
a GPS receiver uses to calculate geographical positions. To determine
a position, data from at least three satellites is required. To determine
elevation, the data from four or more satellites is required. Accuracy of
the positioning varies from 10 feet to several hundred feet, depending
on vehicle placement and the surrounding environment.
Geographical terrain (such as mountains), man-made structures (such as
highway overpasses, bridges, and tall buildings), as well as weather
can interfere with the GPS signal. For best GPS reception, position the
device and mount with a clear line of sight to the sky. Some vehicles
may have a limited view of the sky due to metal sun shields or a
metallized windshield coating.
Map data includes the geographical coordinates for address locations
and points of interest (POIs). With GPS reception, your device calculates
a route to your selected location.
VIP Customer Support

Questions about using OverDryve™? Our team is ready to help.
Call toll-free:

800-237-7270
E-mail:

support@randmcnally.com

OverDryve™ Pro User Manual

Table of Contents
1. Your OverDryve™.......................................................................................................................................................................... 1
Caution: Important Safety Information......................................................... 1
Box Contents............................................................................................................ 2
Install the Mount.................................................................................................... 2
Using the Android Home Screen..................................................................... 4
2. Getting Started.....................................................................................................5
Setup........................................................................................................................... 5
Connect to the Internet................................................................................ 6
Register Your Device...................................................................................... 7
Connect to Bluetooth.................................................................................... 8
Connect to Your Truck Stereo.................................................................... 9
Device Settings...................................................................................................... 11
3. Messaging............................................................................................................ 14
4. Phone...................................................................................................................... 16
5. Navigation.............................................................................................................17
How the Truck GPS App Works .....................................................................17
Main Menu..............................................................................................................18
Preferences.............................................................................................................19
Search For an Address........................................................................................23
Helpful Tips on Entering Addresses......................................................24

Weather............................................................................................................33
Fuel Prices........................................................................................................34
Route to Here, Set Origin, Add as Via..................................................35
6. Truck Tools...................................................................................... 36
7. DriverConnect................................................................................ 41
8. TripMaker.............................................................................................................. 42
9. Road Atlas............................................................................................................. 43
10. Cameras................................................................................................................. 44
Dash Cam................................................................................................................45
Video Files.......................................................................................................45
11. Entertainment..................................................................................................... 46
Bluetooth Player....................................................................................................46
Phone Playback..............................................................................................46
FM Transmitter......................................................................................................47
SiriusXM Radio......................................................................................................48
SiriusXM Functions..............................................................................................49
12. Troubleshooting.................................................................................................51
Restarting the Device.........................................................................................51
13. More Information............................................................................................. 52

Route Map Window............................................................................................25
View Directions..............................................................................................26
Exits Quick View............................................................................................28
Virtual Dashboard.........................................................................................29
Traffic.................................................................................................................31
OverDryve™ Pro User Manual

iii

Your OverDryve™

Caution: Important Safety Information
Navigation

Device

•

Do not use sharp-edged objects on the device touch screen.

•

Protect the device from extreme temperatures. Operating
temperature for the device is between 32 degrees F and
120 degrees F.

•
•

Use this device at your own risk.

Attend to this device only when it is safe to do so.

Traffic laws and regulations always have priority over any instructions
from the navigation system.

NOTE: If you do not understand the spoken instructions or are unsure of
what to do, refer to the navigation map on your device.

Installation
•
•
•
•
•
•
•

Make sure that the mount is securely mounted and properly
adjusted before each trip.

•

•
•
•

The device is not waterproof and is not protected against
water damage.

Do not open the device casing.

Do not attempt to replace the battery. Contact Rand McNally
Customer Support with questions about the battery.
Always follow local regulations when disposing of this device.

Make sure that the mount does not impair the driver’s visibility.

NOTE: Make sure that there are no kinks in the cable and that it will not be
damaged by any sharp objects.

Install the mount in a manner that minimizes risk in the event of an
accident.

NOTE: Use only a moist cloth to clean the device.

Do not attach the mount within the airbag deployment zone.

After installation, check all safety-related equipment to ensure that it
operates without interference from the device, its cables,
or
any other accessories.

NOTE: Do not pull the cable to unplug the unit.

Connect the wall charger to a 120V or 240V outlet only.
Connect the vehicle charger to a 12V outlet only.

OverDryve™ Pro User Manual

Your OverDryve™

Box Contents

Install the Mount

•1 OverDryve™ tablet

Note: Follow all local regulations governing the placement of the mount.

•2 Smart mount

•3 Anti-glare screen protector

Select an area with a line of sight to the sky and GPS satellites.

2. Clean and dry the mounting area.

•4 Bracket with suction cup

3. Remove the suction cup protective film.

•5 FM transmitter antenna

4. Attach the two pieces of the mount together and lock into place.

•6 Dash mount disc

5. Adjust the angle of the mount.

•7 AUX cable

6. Pull the suction cup lever up to release suction.

•8 Vehicle charger

•9 USB wall charger

•10 SiriusXM antenna

Plug the power cord into the mount and the vehicle’s 12-volt
power source.

8. Optional: To use your vehicle’s speakers, connect an AUX cable from the
Smart Mount AUX out to your vehicle’s AUX in port.
9. Optional: To use the SiriusXM satellite radio features, see the instructions
in Section 11 (Entertainment).

10. Place and hold the mount suction cup against the
mounting surface.

11. Press the suction cup lever down until it snaps into place.

12. Snap the tablet onto the mount.

13. Adjust the tablet so that it can be easily seen and does not
block the driver’s line of sight.

9
10

OverDryve™ Pro User Manual

Your OverDryve™

1.
1

Swipe down to view
notifications and settings

4
3

6
5

Your OverDryve™

Using the Android Home Screen
After you turn on your device, the home screen will display.
At the top of the home screen is the status bar. It displays important
information like your Wi-Fi connection, remaining battery life, time, etc. The
status bar will display at the top of almost every screen.
Swipe down at the top of the status bar and your Notifications panel will
display. The tablet notifies you when something needs your attention, such
as an e-mail, text message, or device update.
Tap or swipe down in the Notifications panel and a Quick Settings panel
will display. The Quick Settings panel contains often used features such as
Wi-Fi connection, Bluetooth, and location services (GPS). It also displays an
Android Settings icon in the top right corner. Tap the Android Settings
icon to access a full menu of device settings.

OverDryve™ Pro User Manual

Notifications icons

GPS indicator

Bluetooth indicator

Wi-Fi indicator

Battery power

Current time

Settings (Android Settings and OverDryve™ Setup)

All apps

Back

Home

View open apps

Getting Started

Setup
Connect to the Internet
Enable the Wi-Fi hotspot on your smartphone or other in-vehicle device
and then connect OverDryve™ or connect to your home Wi-Fi to complete
setup.
Register your device
Register with Rand McNally for updates and support.
Connect to Bluetooth
Enable Bluetooth on your smartphone and pair OverDryve™ to enable
hands-free calling and texting, music streaming, and voice assistance.
Connect to your truck stereo system
You can listen to audio through any of the following four methods:
1.

Plug an AUX cable into the Smart Mount and the AUX port in your truck
Note: Do not plug the AUX cable into the audio out port on
OverDryve™.

2. Use the Smart Mount speaker.

3. Use the FM Transmitter. To use the FM transmitter, attach the antenna
to the Smart Mount. On OverDryve™, tap Entertainment > FM
Transmitter and follow the instructions

4. Add an AUX input to your existing truck. Visit randmcnally.com/auxinstall to learn more.

Note: If your device has not been able to detect your location, you may be
asked to set your time zone.

OverDryve™ Pro User Manual

Getting Started

Connect to the Internet
First activate the Wi-Fi hotspot on your phone or in your truck. From the
OverDryve™ setup screen, tap Get Started to begin the setup process. Tap
Find my hotspot.

Select a Wi-Fi network and connect.

A message will display that states you are connected. Tap Next.

OverDryve™ Pro User Manual

Getting Started

Tap Next to proceed to the next step.

OverDryve™ Pro User Manual

Getting Started

Connect to Bluetooth
Connect to your phone via Bluetooth to allow OverDryve™ to call and text
hands-free and to stream music from your phone to your truck’s
stereo system.
First enable Bluetooth on your phone.
From OverDryve™:
1.

Tap Connect.

2. Tap Scan For Devices. A Bluetooth pairing request will display on your
OverDryve™.

3. Tap Pair. If successful, the screen will display a connected message. If
the OverDryve™ failed to connect, verify that your phone is in range and
Bluetooth is enabled.

Help for Connecting to Bluetooth
If you are having issues connecting OverDryve™ to your smartphone via
Bluetooth, these steps can help:
1.

Make sure that your OverDryve™ and smartphone are in close proximity
to each other, preferably within five feet.

2. Check that both devices do not have a low battery. Some devices will
disable Bluetooth to conserve power when the battery gets low.
3. Power the devices off and then back on.

4. Turn off any devices that may be interfering with the Bluetooth
connection. For example, if you usually pair your OverDryve™ with a
different phone, turn off that phone.

OverDryve™ Pro User Manual

Getting Started

Connect to Your Truck Stereo
To listen to audio through your truck stereo, the tablet must be in truck
mode. To put the tablet in truck mode, place it on the Smart Mount and
plug the mount into a power source using the vehicle charger.
The optimal way to connect to your truck stereo is with the provided AUX
cord. You can also connect wirelessly via OverDryve’s FM transmitter.
To connect with the AUX cable:
1.

Tap Connect via AUX.

2. Plug the right-angle end of the AUX cable into the OverDryve™ Smart
Mount.
Note: Do not plug the AUX cable into the audio out port on
OverDryve™.

3. Plug the other end into your truck’s AUX jack.
4. Set your truck’s audio source to AUX.
To use the FM transmitter:
1.

Attach the FM antenna to the Smart Mount.

2. Unplug the AUX cable if it is plugged in.

3. Tap the settings icon located in the top right corner of the OverDryve™
screen.

4. Tap OverDryve™ Setup > Audio > Connect via radio.

OverDryve™ Pro User Manual

Getting Started

Connect to Your Truck Stereo (Continued)
Using the OverDryve™ Speakers
Your tablet has its own speaker, and there’s another powerful speaker in the
Smart Mount. You can use the OverDryve™ speakers instead of connecting
to your truck stereo. If you want to connect to the truck stereo later, tap the
Settings icon in the top right corner of the screen, then OverDryve™ Setup
> Audio.

OverDryve™ Pro User Manual

Getting Started

Device Settings
Swipe down from the top of the screen to view the Quick Settings panel
and adjust the following frequently used features:
•

Battery Power

•

Brightness – Changes the screen brightness

•
•

Wi-Fi – Shows available networks

•

Bluetooth

•

Auto Rotate – Controls whether the screen rotates
when you rotate the tablet

•

•
•

OverDryve™ Pro User Manual

Settings Icon – Access a full menu of all settings

Airplane Mode – Turns off Wi-Fi and Bluetooth

Location – Turn on/off location services (GPS)

Cast screen – Project your screen onto a compatible device.

Getting Started

From the Quick Settings panel, tap the Settings icon to access a full menu
of settings for your device.
Wireless and Networks
•

Wi-Fi – View and connect to available Wi-Fi networks.

•

Date Usage – View your Wi-Fi and app usage.

•

Bluetooth – Pair with your smartphone using Bluetooth.

Device
•

Display – Set brightness, wallpaper, appearance, etc.

•

Storage – View how much storage is available on your OverDryve™.

•

•
•

OverDryve™ Pro User Manual

Sound & Notification – Set volumes for different features and enable
and disable sounds.
Battery – View time spent on battery and battery power used
by different apps.

Apps – View apps. Swipe left to view: downloaded, running, all.

Getting Started

Personal
•
•
•
•
•

Location – View location mode, location requests, and location
services. High accuracy mode is recommended.

Security – View lock,password,encryption, and credential settings.
Accounts – View and add accounts for the Rand McNally market.
Language & input – Set language and keyboard information,
as well as speech options and pointer speed.
Reset Tablet – Reset the device to its factory settings.

System
•

Date & time – Set date, time, time zone, and date and time format.

•

Printing – Enable printing services.

•

OverDryve™ Pro User Manual

Accessibility – Enable spoken feedback, captions, and large text help
visually impaired users.
About tablet – View battery and network status. Also view legal
information such as model numbers and build numbers.

Messaging

Pair OverDryve™ with your iPhone or Android phone via Bluetooth to send
and receive texts hands-free. The OverDryve™ Voice Assistant integrates
with your phone’s voice assistant. OverDryve™ automatically syncs your
text messages so you can see new messages and browse through old ones
without reaching for your phone.*
Note: If you have an iPhone, make sure your phone is not open to the
messaging screen. When the messaging screen is open, the iPhone
automatically marks the message as “read”. The iPhone won’t transmit “read”
messages over Bluetooth, so OverDryve™ will not be able to access them.
To send and receive texts hands-free, tap the Voice Assistant
which will ask who you would like to text. Speak the name of any of your
contacts. The Voice Assistant will prompt you for your message and then ask
you if you would like to send it. The Voice Assistant can also read back text
messages that you receive.
Set your favorite contacts by clicking the star icon next to their names. Easily
access them in the favorites tab.
If you want to send a text without using the Voice Assistant*:
1.

Tap Messaging.

2. Enter the phone number or select a name from your Contacts.
3. Tap the yellow messaging icon.

4. Tap Write a message in the lower left corner of the screen.
5. Write the message and tap the blue arrow to send it.
Supported on Android phones only.

OverDryve™ Pro User Manual

Messaging

To enable text message notifications:
1.

From Messaging, tap the Settings icon in the top left corner of the
screen.

2. Tap Settings.

3. If Enable Messaging Notifications is checked, notifications are already
enabled. If not, tap to turn on the feature. The status will show “Enabled”.
To control what text message information displays on OverDryve™:

From Messaging, tap the Settings icon in the top left corner of the
screen.

2. Tap Settings.

3. If Show Message Content is checked, tap to uncheck. The status will
change to “Hide Content”.

OverDryve™ Pro User Manual

Phone

Pair OverDryve™ with your iPhone or Android phone via Bluetooth to make
calls hands-free. OverDryve™ automatically downloads your contacts and
call history when you get in the truck.
Set your favorite contacts by clicking the star icon next to their names. Easily
access them in the favorites tab.
To set the ringtone or notification ringtone:
1.

From Phone, tap the Settings icon in the top left corner of the screen.

2. Tap Settings.

3. Tap Ringtone or Notification Ringtone and choose your selection.

OverDryve™ Pro User Manual

Navigation

How the Truck GPS App Works
• When your tablet is attached to the magnetic mount, the Truck GPS
boost within the mount will provide accurate GPS location, even without a
Wi-Fi connection.
• Weather, traffic, fuel prices, local search within the Truck GPS app
(including hands-free navigation), and device updates require a Wi-Fi
connection.
• To exit the Truck GPS app at any time, swipe down from the top of the
screen or up from the bottom to view the Android menu bars. Or, tap the
home button on the top of the device.

OverDryve™ Pro User Manual

Navigation

Main Menu

Basic Map View

1 Search For an Address
Tap to type in any address or search by keyword.

Compass
Direction
2
Tap to change the map display. An icon displays the selected option:
North up (N), heading up (arrow), or 3D.

5
6

` 4 Route Distance
Reflects the distance from your point of origin to your destination.
5

Zoom Out
Tap to zoom out.

Map View Tab
Tap to expand the map screen. By default, icons are minimized to
show simply the search bar, compass direction, and zoom. Tap again
to switch back to the default view.

Expanded Map View
7

7
8

Live Data
Tap to view fuel, weather, and traffic along the route. (Requires Wi-Fi)

Virtual Dashboard

OverDryve™ Pro User Manual

Exit Points of Interest (POI)
Tap to view POIs along the exit ahead.

Zoom In
Tap to zoom in.

Current Speed
Tap to display the Virtual Dashboard.
Clock/Elevation
Tap to toggle between the clock and elevation.
Preferences
Tap to set general, route, map, or warning options.
18

5.
Preferences
•

Tap

and

to view the options.

•

Tap the option to be set.

•

Tap Back

•

General Preferences

Manage Custom POIs
Select a Category to Edit
Hide All Icons on Map
Go to Map

Mileage Log

Truck/Bus Only
Car Only
Truck & Car
Don’t Log Mileage

Screen Click

Click Off
Click On

to save changes.

General Preferences

Options

My Custom POIs

Enter the new information.

System Settings

System Settings
GPS Repair
System Update

Skin Type

Modern
Classic

Tutorial

View Tutorial and Tips

Vehicle Type

Truck
Car/Light Truck
Bus

Voice Name

Yard Time Zone

Hawaii
Alaska
Pacific Time
Arizona
Mountain Time
Central Time
Indiana (East)
Atlantic (Canada
Newfoundland

Allison
Samantha
Susan
Tom

Language

English (Basic)
English (Advanced)
Español
Français

Day / Night Mode

Automatic
Always Day
Always Night

OverDryve™ Pro User Manual

Navigation

For the screen and spoken instructions.
Units

U.S. Standard
Metric
Auto Select

Load Prompt/
Notification

Prompt
Always Loaded

5.
Preferences - continued

Route Preferences

General Preferences

Options

Toll Prompt/
Notification

Enabled
Disabled

Clock Setting

12-Hour Clock
24-Hour Clock

Contact & About

Tap to show version information and
copyrights.

Route Preferences

Options

Turn Announcements

Set three distances at which you want
to be warned about an upcoming turn.
The first announcement will be the farthest
from the turn and the third the closest.

Junction View Distance
Tap - r + to set the distance
ETA Adjustment

Increase ETA more
Increase ETA some
ETA OK
Decrease ETA some
Decrease ETA more

Route

Fastest Route
Shortest Route

Options

Note: The default settings for your device were optimized for the vehicle
route. Use the options below to fine-tune these settings.
Use Traffic

On
Off

Tollways

Recalculation

Manual Recalculate
Auto Recalculate

Allow Tollways
Avoid Tollways

U-Turns

Allow U-Turns
Avoid U-Turns

Freeways

Allow All (Default)
Avoid Freeways
Avoid Small Roads
Prefer Freeways

Cross Country Borders

Allow Crossing Borders
Avoid Crossing Borders

Dirt Roads

Allow Dirt Roads
Avoid Dirt Roads

Manage Avoid List

Roads
States/Provinces
Areas
Routes

Fast Recalc

Off
On

Ferries

Allow Ferries
Avoid Ferries

Tunnels

Allow Tunnels
Avoid Tunnels

Manage Avoid List

Roads
States/Provinces
Areas
Routes

OverDryve™ Pro User Manual

Navigation

Preferences - continued
Map Preferences

Options

Map Preferences

Options

.Map Style

Light
Dark
High Contrast

Map Auto Zoom

Off
On, Auto Scale
On, Street Scale
On, City Scale
On, State Scale

Address Book Icons

Off
On

Set to auto scale to keep the current
vehicle position and the next turn
in the map view at all times. Set to
street/city/state scale to specify the
maximum scale of the zoom.

Truck Icon

2D
3D

Bus Icon

2D
3D

Car/Light Truck Icon

2D
3D

Note: When in 3D Map mode with
Auto Zoom on, the map will change
to North Up at certain zoom levels. Also,
the visual turn screen will not appear in
3D mode with Auto Zoom on because a
close up view of the turn is not needed.
Lane Guidance

Off
On

POI Icons

Off
On

Truck POI Icons

Off
On
Select icons to display on map.

Scroll left or right to select the vehicle
icon and color to display on the map.
Map View Mode

Heading Up
North Up
3D View

Route Color

Move the slider to the left or right to
set the route color.

Select icons to display on map.
Select restaurants, banks, gas
stations, etc. to display on the
map. Tap any category to fill in the
square and display those icons.
OverDryve™ Pro User Manual

Navigation

Preferences - continued
Warning Preferences
Warning/Alert Prompts

Auto Dismiss Warnings

Options
None
Audio & Visual
Visual
Audio
Never
After 2 Seconds
After 10 Seconds
After 30 Seconds

Warning Preferences Options
Warning Display Size

Full Screen
Small Bar

Toll Booth Alert

Set warning distance to toll booths
by using the + and - buttons.

Construction Area

Set warning distance to construction
areas by using the + and - buttons.

Speed Limit

Set warning distance to speed limit
changes by using the + and - buttons.
Set the amount over the posted limit at
which the warning appears.
Set a user-defined maximum speed to
be warned whenever the vehicle
exceeds that speed, regardless of limits.

Curve Warnings

Set warning distance to curves
areas by using the + and - buttons.

Hill Warnings

Set warning distance to upcoming hills
areas by using the + and - buttons.

Engine Brake Warnings

Set warning distance to begin braking
areas by using the + and - buttons.

Speed Limit Change

Narrow Road Warnings

Set warning distance to narrow roads
areas by using the + and - buttons.

Weigh Station

State/Province
Border Alert

Set warning distance to state/province
borders by using the + and - buttons.

State or Province Border/
Timezone Change

Off
On

OverDryve™ Pro User Manual

Set warning distance to a change in
the speed limit by using the + and buttons.
Set warning distance to weigh stations
by using the + and - buttons.

Note: To turn warnings off completely, tap “-” until OFF displays.

Navigation

Search For an Address
1.

Tap the search bar at the top of the Navigation screen to type in any
address or search by keyword. Or, tap any of the categories to search for
specific types of destinations.

2. Once a destination is entered, tap Navigate and your route options will
display.
3. Select either the fastest route or an alternate route.
4. Tap Start Navigation to begin the route.

OverDryve™ Pro User Manual

Navigation

Helpful Tips on Entering Addresses
Auto-Complete Feature
Enter the first few characters in a name and a short list displays
names that start with the typed characters. Continue entering characters
until the searched-for name displays
in the list. Tap the name to select it.
Cities
Cities with common names, such as “Athens”, may have multiple locations.
The tablet will list all locations. If a name does not display, continue typing
characters until the name you are looking for displays in the list.
State or County Routes
If you’re entering a State or County Route, it’s usually best to first either enter
the State or County initials, (for example, State Road 535 would be entered
as “SR”) but you may also need to try other options, such as “State Road” or
“CA” for California, for example.
Truck Loads
After setting a destination, you must confirm if the truck is loaded or not. Tap
a button to indicate:
Empty: The truck is not loaded
Loaded: The truck is loaded
Always Loaded: The Loaded option will always be selected, and this page
will no longer display.

OverDryve™ Pro User Manual

5.
Route Map Window
1

6
7
9
11
13

8
10

12
14

Exit Quick View
Tap to view POIs along the exit ahead.

Live Data
Tap to view fuel, weather, and traffic along the route.

Zoom In
Tap to zoom in.

` 9 Route Distance
Reflects the distance from your point of origin to your destination.
10

Zoom Out
Tap to zoom out.
Speed Limit
Tap to open a “Tell Rand” message about speed limits.

Map View Tab
Tap to minimize the icons displayed. Tap again to switch back.

Next Maneuver
Distance to the next maneuver. Tap to zoom in.

Route Options
Tap to change route settings, save, or cancel the route.

Road Name
Name of the street you will turn onto next.

Virtual Dashboard

Search For a Address
Tap to type in a new address or search by keyword.
3

4 View Directions
Tap to select a Route Display Option, such as detail view, highway view,
trip summary, or summary map view.
5
Compass
Direction
Tap to change the map display. An icon displays the selected option:
North up (N), heading up (arrow), or 3D.

OverDryve™ Pro User Manual

Navigation

Current Speed
Tap to display the Virtual Dashboard.

Current Information
Tap to view current information by city, street, or upcoming intersection.
Also displays advanced lane guidance and weather overlay key, when
enabled. Tap to change.
16

17 ETA/Remaining

Mileage and Elevation
Tap to toggle between ETA/Mileage and elevation.

Preferences
Tap to set general, route, map, or warning options.
25

Navigation

View Directions

Detail View

Route Display Options
1

When first opened, the slide-out list displays in Detail View showing each
maneuver.
Use

and

to view the instructions.

To change the route display, choose Detail View, Highway View, Trip
Summary (for multi-stop trips), or Map View (to view the route from start to
finish).

1 Distance
Displays the distance for each road segment.
2 Street/Road Name
Displays the street name you will be on after performing the next
maneuver. Tap any item in the list to view it on the map and to detour
around it if necessary.

Highway View

3 Leg
Number of the leg (for multi-stop trips) and distance.

Highway Name
Displays the highway you will be on.

OverDryve™ Pro User Manual

5.
View Directions Continued

Trip Summary View (for multi-stop trips)

1 Total Distance and Time
Displays the total distance and time for the entire multi-stop trip.

1
3

2 Leg
Number of the leg (for multi-stop trips) and distance.
3 Destination
Destination for that leg of the trip.
4

Map View (entire route)

OverDryve™ Pro User Manual

Navigation

Remove Stop
Tap to remove the stop from the trip.

Navigation

Exits Quick View
Slide out to show Points of Interest and amenities at upcoming exits.
The list displays the distance to the next exit, exit number, and a count of
available amenities.
1.

Tap an exit to bring up a list of POIs and amenities at that exit.

2. Tap All, Fuel, Food, or Hotel to display locations by category.
3. Tap any item in the list to route to that location.

OverDryve™ Pro User Manual

Navigation

Virtual Dashboard
To show the Virtual Dashboard, tap the Virtual Dashboard icon or the
Current Speed.
1

Gather trip information for up to three trips.
Includes odometer settings, hours, and speeds.

Return to the Route Map Window.

Sunrise and sunset times based on vehicle location
(latitude/longitude) and day.

Current speed
NOTE: Turns red when speed limit warning exceeded.

Tap here

Elevation at current location.

Nearest cross street and current location.

Latitude and longitude of your current location.

Save your current address to your address book.

Set your current location as the route origin.

Reset trip information for the selected trip (Tab 1, Tab 2 or Tab 3).

Select to automatically reset the information in each tab after
the vehicle has remained stationary for the specified number of hours.

4
12

9
OverDryve™ Pro User Manual

Percentage of current trip completed, distance to next maneuver,
and the number of miles and time spent on the trip to this point.

11
29

Navigation

Manually Reset Trip Information
To manually reset trip information:
1.

Tap the tab you want to reset (1, 2, or 3).

2. To set the odometer for the selected tab back to zero, tap Reset.
Information is captured as you travel the route.

Automatically Reset Trip Information
To reset trip information after the vehicle has remained stationary after
a specific number of hours:
1.

Tap the tab you want to reset (1, 2, or 3).

2. Tap Auto Reset.
3. Tap

4. Tap

to increase the number of hours.

to decrease the number of hours.

5. To save changes, tap Change. The tab displays the auto reset number
of hours.

OverDryve™ Pro User Manual

Navigation

Traffic
NOTE: This feature requires a Wi-Fi connection.
1

To view current traffic information along your route and near your
location:
1

Tap Live Data > Settings on the map screen. Tap the Traffic radio
button to display the traffic overlay on the map.

Tap the Traffic tab.

The Traffic tab displays traffic events along your route.

Use the Flow and Incidents checkboxes to view or hide each type of
traffic events

Tap the X to return to the map.

Traffic pattern display on the map as colored lines.
Traffic Incidents display as icons.
Traffic indicators:
Green: Light or no traffic
Yellow: Moderate to heavy traffic
Red: Slow traffic

OverDryve™ Pro User Manual

Navigation

Traffic Icons

Accident

Exit blocked

Accident

Entrance blocked

Incident

Closure

Carriageway

Traffic

Carpool

Road Work

Obstruction

Dangerous

Road Condition

Temperature

Chance of Precipitation

Wind

Activities

Security

Delay

Cancel

Travel Time

Size/Weight Limit

Visibility

Heavy
Traffic

OverDryve™ Pro User Manual

Moderate
Traffic

Light
Traffic
32

Navigation

Weather
•

This feature requires a Wi-Fi connection.

•

Weather display depends on active weather patterns and
map zoom level.

•
1

The refresh speed of the weather display is dependent on the
connection speed. Weather information is updated every few
minutes while the Wi-Fi connection is active.

To view current weather information and the three-day forecast for
your location, tap Live Data > Settings on the map screen and tap the
Weather tab.
1

View details for current weather alerts.

Select type of weather overlay to display on the map.

View weather information at your destination.
NOTE: You can view weather information at any other location
by tapping the map and then the Wi-Fi icon and the Weather tab.

Select from a variety of weather types to display on the map:
•No weather (turn off )
•Traffic impact
•Temperature
•Feels like
•Current precipitation intensity and type
•Probability of precipitation
•Forecasted precipitation intensity, type, and clouds
•Forecasted precipitation intensity and type
•Dew point
•Relative humidity

•Wind speed
5

Tap to toggle between weather, city, street,
and/or intersection.
OverDryve™ Pro User Manual

Slide to adjust the transparency of the overlay on the map.
Note: Use the slider to readjust for visibility when switching
between day and night modes.
33

Navigation

Fuel Prices
Note: This feature requires a Wi-Fi connection.
To show fuel prices, tap Live Data on the map screen and
tap Settings > Fuel Prices.

OverDryve™ Pro User Manual

Displays stations and prices, with distance as the crow flies.

Check to show the icons and prices on the map screen.

Sort by distance.

Apply filters for type of fuel and specific brand.

Check to show fuel prices along the route.

Navigation

Route to Here, Set Origin, Add as Via
You can drag the map with your finger to move it to another location. The
crosshairs will display when you move the map. Place the crosshairs over the
location you are looking for. When you find the location, press and hold the
screen for a few seconds and choose Route to Here, Set Origin, or Add
as Via.

1
3
5

OverDryve™ Pro User Manual

Crosshairs
Drag the crosshairs over the desired location.

Route to Here
Tap Route to Here to navigate to the location.

Set Origin
Tap to set the location as the origin. The origin is the starting point of
the route.

Save to Address Book
Add the location to your address book.

As as Via
Add the location as a via point (interim stop) between the origin and
the destination.

Permanent Avoid
Add the location as a point to avoid on all future routes.

Truck Tools

Truck Tools
Note: Some features are not available in Truck mode.
Truck Info: Enter truck information (weight, length, etc.).
Status, Trails, Mileage, and Fuel: View driving, on-duty, and maintenance
timers; state logs; trails;and fuel purchase information.
Motor Carrier’s Road Info: Quickly access contact information for
emergency and local regulatory agencies.
Fuel Manager: Track fuel efficiency, usage averages, maintenance, and
repairs. Requires a separate account.
Motor Carrier’s Road Atlas: Displays the Road Atlas app.
Notes: Add, edit, and manage notes.
Calendar: Sync with an existing calendar program.
Calculator: Access a scientific calculator.
Quick Planner: Between any two cities or towns, quickly calculate the
distance, driving time, and cost.
Tell Rand: Compose a message to send to Rand McNally.
Truck It Smart: Locate loads or trucks in your area, and fulfill routine,
last-minute, rush or complex freight orders with ease. Requires a separate
account.
Unit Converter: Quickly convert distance, weight, and temperature.

OverDryve™ Pro User Manual

Truck Tools

Status
Note: Odometers count up and record the current mileage. Maintenance
counters count down. When a maintenance timer counts down to 2,000
miles, a reminder displays each time the TND starts.
1.

Tap Truck Tools.

2. Tap Status, Trails, Mileage, and Fuel.
3. Tap the Status tab.

Tap a field to make adjustments to mileage. The mileage continue to count
down from the changed value.
1.

Tap -- to decrease the setting.

2. Tap + to increase the setting.

3. Tap the calculator to display a keyboard. Enter a number and tap Enter.
4. Tap Change.

n the right, use the Reset To field to set the most common reset
O
value, normally zero. At the beginning of each day or run,
tap Reset to set the value back to zero for odometers and 15,000
or 35,000 for maintenance odometers.
1.

Tap -- to decrease the setting.

2. Tap + to increase the setting.

3. Tap the calculator to display a keyboard. Enter a number and tap Enter.
4. Tap Reset.

OverDryve™ Pro User Manual

Truck Tools

Mileage
1.

Tap Truck Tools.

2. Tap Status, Trails, Mileage, and Fuel.
3. Tap the Mileage tab to view list of logs for the current year,
ordered by quarter.
4. To view quarterly mileage logs for previous years, tap Year.
Tap on a quarter to view log entries.
5. Tap on a quarter to view details. Tap View by Date/View by State
and Empty/Loaded for more information.
To delete a log, tap on the
Tap Yes to delete the log.

next to the log entry to be deleted.

Note: Load Option and Driver Status control how logs are recorded.

OverDryve™ Pro User Manual

Truck Tools

Trails
Use Trails to record a “bread-crumb” path of GPS coordinates where
your truck has traveled.
1.

Tap Truck Tools.

2. Tap Status, Trails, Mileage, and Fuel.
3. Tap the Trails tab.
4. To record a trail, tap New Trail.
5. To end the trail, tap the pause icon on the map screen.
6. The trail is recorded in the Trails tab.
7. Tap on a trail to view details.
8. Tap Show on Map to display the trail on the map screen.
9. Tap Edit Name to change the name of the trail.
10. Tap Set Color to change the color of the trail.
Note: The Trails feature is also accessible from the Address Book.

OverDryve™ Pro User Manual

Truck Tools

Fuel Logs
1.

Tap Truck Tools.

2. Tap Status, Trails, Mileage, and Fuel.
3. Tap the Fuel tab to view a list of fuel logs by quarter.
4. Tap +Fuel to record the date, location and cost of fuel purchase.
5. Tap on any field to edit.
6. Check Taxable to include the purchase in the fuel log.
7. Tap Save (Note: Fuel economy is calculated automatically.)
8. Once fuel purchases have been entered, tap on a quarter to view the
details.
9. You can View by State or View by Month.
10. Tap the state or month to view fuel purchases.
11. Tap View All to see all fuel purchases.

OverDryve™ Pro User Manual

DriverConnect

DriverConnect
The DriverConnect app provides a fully-compliant electronic logbook
solution. DriverConnect lets you track and log Hours of Services,DriverVehicle Inspection Reports, Fuel purchases, and more. Reports can be
generated for roadside inspections.
The DriverConnect app connects to a Rand McNally Electronic Logging
Device (ELD) over a Bluetooth connection. The app automatically syncs
driving data from the ELD with the Rand McNally DriverConnect web
services via a Wi-Fi or cellular transmission.
Visit http://www.randmcnally.com/category/e-logs for up-to-date
information on compatible ELDs.

Sign Up or Log In
To use DriverConnect,you must log in with an existing account, or create a
new account. If you are part of a fleet, your Fleet Manager will provide login
information for you.
You can use your login information to access the DriverConnect portal,
where you can view reports and stored information.
Visit https://www.driverconnect.randmcnally.com to access the
DriverConnect portal.

OverDryve™ Pro User Manual

8.
1

TripMaker

TripMaker is a trip planning app that allows you to easily browse the map
and set up a multi-stop trip. Add via points and send your trip to the GPS
app for routing. To access TripMaker, tap the app tray, swipe to the right to
view the second app screen, then tap the TripMaker icon.
To create a trip:
1.

Enter the starting and ending point for your trip.

2. Choose a name for it.
3. Tap Create Trip.
1

Access Menu
Manage your trip options, such as update route and fuel costs.
I tinerary
View your itinerary.

irections
D
Once your trip is created, tap this icon for driving directions.

My Trips
Access trips that you have created.

Points of Interest
Search categories along your route, such as The Great Outdoors.

earch
S
Search for an address or place along your route.

Create a Trip
Enter addresses, cities, states, or zip codes to create a trip. Add stops
as needed. TripMaker will automatically order stops to minimize driving
distance, but you can re-order stops by pressing and dragging stops to
your desired position along the route.
7

8 Manage Menu
Manage your account settings, map options, and find online help.

OverDryve™ Pro User Manual

9.
2

Road Atlas

The Rand McNally Road Atlas is a digital version of
Rand McNally’s Road Atlas.
1

Legend
Tap Legend at the top right of the screen to view the roads and
related symbols.

Maps
Tap Maps at the top right of the screen to select pages by state/
area. You can also update maps here.
2

OverDryve™ Pro User Manual

10.

Cameras

Your OverDryve™ tablet includes a built in dash cam; the lens is in the back
of the device. The Wi-Fi backup camera accessory is sold separately.

OverDryve™ Pro User Manual

10.

Cameras

Dash Cam
The Dash Cam records a video loop as you drive. Tap the red button to start
or stop recording.

Records Video

Use the settings icon in the upper right corner of the camera screen to
access preferences for video quality, audio, and segments.

Video Files
You can record sound and use an external storage device to keep longer
videos. Use the table below to choose Quality, Segments, and Length based
on the space used.
Video
Quality
Low

Number of
Segments
4

Length of Segments
(Minutes)

Disk Space
Used

Low

486 MB

High

Low

High
High

OverDryve™ Pro User Manual

43.26 MB
1.58 GB
89 MB

1006 MB
3.28 GB

11.

Entertainment

There are four options for listening to music, podcasts, audiobooks, etc.:
1.

Stream music from your smartphone via Bluetooth. Access the audio
controls in the Bluetooth Player.

2. Stream music right from OverDryve™ by downloading music apps.

3. Download mp3s or other types of audio files. Access the audio controls
in the Media Player.
4. Listen to SiriusXM satellite radio.

You can activate the FM Transmitter to listen to audio through your
speakers. For more ways to listen to audio, refer to “Connect to Your Truck
Stereo” on page 9.
Note: To listen to music, the tablet must be in truck mode. To put the tablet
in truck mode, place it on the Smart Mount and plug the mount into the
vehicle adapter.

Bluetooth Player
The Bluetooth player lets you stream any audio (music, podcasts,
audiobooks, etc.) from your phone to OverDryve™. To get started, play some
music from your phone. On OverDryve™, tap Entertainment > Bluetooth
Player. Swipe right or left anywhere on the Bluetooth player screen to
change tracks. For optimal sound, turn the volume on your phone and
OverDryve™ up all the way.
Note: For help with connecting to Bluetooth, see See “Connect to
Bluetooth” on page 8.

Phone Playback
You can control your phone’s audio controls such as Next, Previous,
Play, and Pause from your OverDryve™. From the main menu, simply tap
Entertainment > Bluetooth Player to access the controls.

OverDryve™ Pro User Manual

11.

Entertainment

FM Transmitter
The FM Transmitter makes it easy to listen to music from OverDryve™. Just
tap Entertainment > FM Transmitter > On. Tune your truck radio to an
open FM station and you’re set.

Finding the Best Station
In order to get the best possible reception from the FM Transmitter on
your truck stereo, you need to find the best FM frequency to transmit to.
The best frequency to use is one where no FM radio stations are currently
broadcasting on or near. FM reception can vary by geography and can also
vary depending on the location of your vehicle’s FM Antenna.
To start, attach the FM Transmitter antenna to OverDryve’s smart mount.
Next, tune your truck’s FM Radio to different stations until you hear only
static on a station. Be sure to use the “Tune” option in your truck and not
the “Seek” option, as Seek will skip over open stations. Once you have found
an open station, open the FM Transmitter app on OverDryve, turn it on and
tune it to the same frequency. You should hear the static stop and you will
now hear any audio playing from OverDryve.
Next, change the direction of OverDryve’s FM Transmitter Antenna until you
get the clearest sound. If you still hear static or the audio from OverDryve
isn’t clear, tune your truck’s FM radio to a different open station and repeat
the process.

OverDryve™ Pro User Manual

11.

Entertainment

SiriusXM Radio
Your OverDryve Pro tablet comes with a SiriusXM radio app pre-installed. To
access SiriusXM,, tap Entertainment > SiriusXM. The SiriusXM antenna
cable must be installed, and the tablet connected to the Smart Mount.
Antenna Cable Routing
When routing antenna cable, always be careful to include enough slack
in your cable to accommodate open doors and driver space. Use things
typically found around the home, like electrical tape, to secure cables in
areas so that hinges do not pinch the cable with the door. Hide any excess
cable in the cabin trim.
Activating Your Radio
After installing your OverDryve Pro tablet with SiriusXM smart mount and
the antenna, launch the SiriusXM application from the ENTERTAINMENT
category. You should be able to hear the SiriusXM preview channel on
Channel 1. If you cannot hear the preview channel, please check the
installation instructions to make sure your SiriusXM smart mount tuner is
properly installed.
After you can hear the preview channel, tune to Channel 0 to find the Radio
ID of your tuner. In addition, the Radio ID is located on the bottom of the
SiriusXM smart mount tuner. You will need this number to activate your
subscription. Write the number down for reference. Note: the SiriusXM
Radio ID does not include the letters I, O, S or F.
In the USA, activate online or by calling SiriusXM Listener care:
www.siriusxm.com/activatenow or 1-866-635-2349
For Canadian Subscriptions, please contact:
www.siriusxm.ca/activatexm or 1-877-438-9677
The SiriusXM satellites will send an activation message to your SiriusXM.
When your radio receives the activation message, your radio will display
“Subscription Updated” Note, the activation process usually takes 10 to 15
minutes, but may take up to an hour. Your radio will need to be powered on
and receiving the SiriusXM signal to receive the activation message.
OverDryve™ Pro User Manual

11.

Entertainment

SiriusXM Functions
Direct Tune
Tap to display the Direct Tune interface.
Up (>) / Down (<)
Click Up (>) / Down (<) to switch to the next available station.
Related
Displays similar genre channels based on the currently playing channel.
FFW, RRW, Pause/Play, LIVE
Fast forward (FFW, >>) and fast backward (RRW, <<) buttons play the songs
as buffered (up to 30 minutes) within the selected station in its entirety.
Pause button stops the music play without skipping any music stream.
Play button resumes music play in a continued stream.
LIVE button stops playing buffered content and syncs with Live broadcast.
Smart FAVORITES
Tune to,or set,a Smart FAVORITE.
TuneScan
Tap to get a short preview of songs that you have missed on each of your
SmartFavorites music channels. Find a song you like and tap the TuneScan
button again to continue listening to that song.
Tune Mix
Tap to play a unique blend of songs from your SmartFavorites music
channels from the current SiriusXM Preset Band.
Categories
Tap to group stations into corresponding genres..
Featured
Tap to display the SiriusXM recommended/promoted channels of the month.

OverDryve™ Pro User Manual

History
Tap to display the channels in the order of most recently listened stations.
History stores the last 8 stations you listened to.

11.

Entertainment

Direct Tune
Scroll to the left or right, or tap the buttons, to scroll
between available stations. You can also type the station number to navigate
directly to that station.
Tap a station icon to listen.
Tap the X to close Direct Tune.

Smart FAVORITES
You can set up to 15 presets,or Smart FAVORITES,in three scrollable panels.
Tap and hold a Smart FAVORITES icon to set the station.
Tap and hold again to:
Replace: Set a new Smart FAVORITES channel over the existing one.
Clean: Delete the Smart FAVORITE
Cancel: Return to the SiriusXM interface.
Once a Smart FAVORITE is set, tap the channel icon to play that channel.

OverDryve™ Pro User Manual

12.
Rand McNally has designed OverDryve™ for speed and reliability. However,
from time to time, all Android devices run into problems. If your unit
becomes unresponsive for any reason, it’s always best to restart the unit by
turning it off and on again.

Restarting the Device
1.

Restart the unit by holding down the power button for 3 seconds, or
until you see the Power Off screen.

2. Press Power Off.

3. Once the unit has shut down, press and hold the power button for 2 to 4
seconds to turn it back on.
If the unit is unresponsive and you don’t see the power down button appear
on the screen, hold down the power button for 10 to 15 seconds and the
device will turn off completely. Once the unit has shut down, press and hold
the power button for 2 to 4 seconds to turn it back on.

Troubleshooting

Resetting the Device
To reset the OverDryve™ to its factory state:
1.

Press the power button to turn it off. If it will not power off, force it to
shut down by pressing and holding the power button for 10 seconds.

2. Press the Volume Up button.

3. While pressing Volume Up, press and hold the Power button. The tablet
will load the Engineering menu.
4. Press the Volume Down button to highlight the “Android Recovery
Mode” option.

5. Press the Power or Volume Up button to select. The Android robot with
an Error sign will display.
6. Press the Volume Down button followed by the Volume Up button and
then release. The tablet will show the system recovery menu.

7. Using the Volume buttons, highlight the “wipe data/factory reset” option
and press the Power button to select.
8. Using the Volume buttons, highlight the “Yes – delete all user data” and
press the Power button to confirm. The screen will indicate that the
data and cache partitions were formatted. The tablet will return to the
Engineering menu.

9. Using the Volume buttons, highlight “reboot system now” and press the
Power button to select.
10. Wait for the tablet to complete its reboot. The tablet will be in factoryreset state.
For additional help and FAQs, visit randmcnally.com/support.

OverDryve™ Pro User Manual

13.

More Information

For more information

OverDryve™ Pro User Manual

•

Rand McNally Website

•

Support

•

Accessories

•

Facebook

randmcnally.com/overdryve
randmcnally.com/support
store.randmcnally.com
facebook.com/randmcnally

Trademarks
OverDryve™ is a trademark of RM Acquisition, LLC, d/b/a Rand McNally.
InfoGation is a registered trademark of InfoGation Corporation.
Local search information provided by CityGrid Media.
Weather data provided by myweather.com.
Fuel prices provided by OPIS.
Traffic information provided by INRIX, Inc.
© 2017 Rand McNally. © 2017 HERE. All rights reserved.
Rand McNally follows a continuous improvement process and reserves the
right to provide enhancements that may not be reflected in the pictures and
specifications in this manual.
The information contained herein may be changed at any time without prior
notification. Neither this manual nor any parts thereof may be reproduced
for any purpose whatsoever without the express written consent of
Rand McNally, nor may it be transmitted in any form either electronically
or mechanically, including photocopying and recording. All technical
specifications, drawings, etc. are subject to copyright law.

OverDryve™ Pro User Manual

Warnings, End-User License Agreement, and Warranty
Pay attention to road conditions and street signs, and obey all traffic and safety laws. Traffic laws and current traffic conditions must always be observed and take precedence over the
instructions issued by the Rand McNally® navigation system. The User should be aware of situations where current traffic conditions and the instructions from the navigation system may be
in conflict. Some states prohibit the use of windshield mounts and may otherwise restrict the usage of navigation and other electronic devices in the vehicle. It is the User’s responsibility to
operate his/her vehicle in a safe manner and to ensure compliance with all laws and regulations. The use of the navigation system does not relieve the User of his/her responsibilities. .
If after reading the following terms and conditions, the User decides not to accept the terms, the User should not use this navigation system.
Rand McNally hereby grants you (“User”) a single-user non-exclusive, non-transferable license to use the Rand McNally navigation system, including software incorporated and associated data
incorporated therein and all related documentation that accompanies the product (hereinafter referred to as the “Product” ) for User’s own internal business or personal use and not for resale
or sublicense .
This Product is furnished under license and may be used only in accordance with the terms and conditions of this license. Except as permitted by such license, the contents of this Product may
not be disclosed to third parties, copied or duplicated in any form, in whole or in part, without the prior written permission of Rand McNally. This Product contains proprietary and confidential
information of Rand McNally and its licensors. Rand McNally grants User a limited license for use of this Product for its normal operation. By using the Product, User acknowledges that the
contents of the Product are the property of Rand McNally and its licensors and are protected by U.S. copyright, trademark and patent laws and international treaties.
THE USER MAY NOT:
• Use the Product on a network or le server, time-sharing or to process data for other persons.
• Use the Product to create any routing tables, les, databases or other compendiums.
• Copy, loan or otherwise transfer or sublicense the Product, its software or content.
• Modify or adapt the Product in any way, or decompile, disassemble, reverse engineer or reduce to human readable form the software incorporated in the Product.
• Alter, remove or obscure any copyright notice, trademark notice, or proprietary legend from the Product.
This license will terminate automatically if User fails to comply with any of the terms of this license, and in such case, User agrees to immediately stop using the Product. Rand McNally may
revise or update the Product at its sole discretion, but it is not obligated to furnish any revisions or updates to User.
RM Acquisition, LLC d/b/a Rand McNally warrants that the Product, and the component parts thereof, will be free of defects in workmanship and materials for a period of one (1) year from the
date of purchase. This warranty may be enforced only by the first consumer purchaser (“Customer”), provided that the product is utilized within the U.S.A. or Canada.
During the warranty term, Rand McNally will, without charge, repair or replace (with a new or newly reconditioned unit), at its option, defective Products or component parts. For repair or
replacement of defective Products, Customer must contact Rand McNally at 1-800-333-0136 for return authorization and instructions. Customer will be required to provide proof of date of
first Customer purchase by providing a copy of the original sales receipt for the warranty to be valid. The Customer must pay any initial shipping charges required to ship the Product to Rand
McNally for warranty service, but the return charges will be at Rand McNally’s expense, if the Product is found to be defective and is repaired or replaced under the terms of this warranty.
If the Product sent in is still under its original warranty, then following repair or replacement by Rand McNally, the new warranty is 90 days or to the end of the original one (1) year warranty,
whichever is longer. If the Product is out of warranty, Rand McNally shall have no obligation to repair or replace the Product, but if it does choose to repair or replace the Product, such repair or
replacement shall be at Rand McNally’s then-current cost. In such case, customer shall be responsible for all shipping charges associated with the shipment of the Product to Rand McNally and
its return to the customer.
This warranty gives the Customer specific rights. Other rights may be available to Customer which vary from state to state.
Exclusions: This limited warranty does not apply: 1) to any product damaged by accident; 2) in the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs;
3) if the serial number has been altered, defaced or removed; 4) if the Product is used other than as provided in the documentation that accompanies the Product, or 5) if the owner of the
product resides outside of the U.S.A. or Canada.

OverDryve™ Pro User Manual

Warnings, End-User License Agreement, and Warranty
CAUTION: RAND MCNALLY MAKES NO WARRANTY AS TO THE ACCURACY OR COMPLETENESS OF THE INFORMATION IN THE PRODUCT, THE SOFTWARE OR THE
DOCUMENTATION, AND DISCLAIMS ANY AND ALL EXPRESS, IMPLIED OR STATUTORY WARRANTIES, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTY AS TO QUALITY, PERFORMANCE, TITLE OR NON- INFRINGEMENT. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO SOME CONSUMERS.
IN NO EVENT WILL RAND MCNALLY OR ITS LICENSORS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE
OR INABILITY TO USE THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
IT IS THE USER’S RESPONSIBILITY TO USE THIS PRODUCT PRUDENTLY AND IN ACCORDANCE WITH THE DOCUMENTATION. THIS PRODUCT IS INTENDED TO BE USED ONLY AS A TRAVEL
AID AND MUST NOT BE USED FOR ANY PURPOSE REQUIRING PRECISE MEASUREMENT OF DIRECTION, DISTANCE, LOCATION OR TOPOGRAPHY.
The User agrees to allow information provided by the User to Rand McNally to be used for internal business evaluation purposes, including, but not limited to, evaluating the effectiveness of
the Product and the services provided and methods to simplify or improve User experiences. Such information will not be provided to third parties in any way that discloses the identity of the
User.
Rand McNally may make use of third party software in the Product. Notwithstanding the terms and conditions of this license, use of some third party materials included in the Product may be
subject to such third party’s terms and conditions. The third party copyright notices are provided at the end of this License.
The User agrees to indemnify, defend and hold Rand McNally and its licensors (including their respective licensors, suppliers, assignees, subsidiaries, affiliated companies, and the respective
of officers, directors, employees, shareholders, agents and representatives of each of them) free and harmless from and against any liability, loss, injury (including injuries resulting in death),
demand, action, cost, expense or claim of any kind or character, including but not limited to attorney’s fees, arising out of or in connection with any use or possession by the User of this
Product.
These terms and conditions constitute the entire agreement between Rand McNally (and its licensors and suppliers) and the User pertaining to the subject matter hereof, and supersedes in
their entirety any and all written or oral agreements previously existing between us with respect to such subject matter. The terms and conditions (including the license) may be updated from
time to time with or without notice.
The above terms and conditions shall be governed by the laws of Illinois, without giving effect to (i) its conflict of laws provisions, or (ii) the United Nations Convention for Contracts for the
International Sale of Goods, which is explicitly excluded. The User agrees to submit to the jurisdiction of Illinois courts for any and all disputes, claims and actions arising from or in connection
with the User’s license and use of the Product hereunder.
User shall not export the Product in violation of any U.S. or foreign laws. Rand McNally’s licensors shall be third party beneficiaries of Rand McNally’s rights under this license, but are not parties
hereto and have no obligations hereunder.
By using this Product you agree to be bound both by the foregoing and to any additional terms of use found at www.randmcnally.com.
Actual toll costs may vary from estimates depending upon a number of factors including inaccurate or imprecise source data and variable toll costs, which are dependent upon vehicle
characteristics (class, axle number, weight, etc.) that vary across toll roads.
Restricted Rights Legend. For governmental agencies: Use, reproduction or disclosure is subject to restrictions set forth in subparagraph (c) (1) (iii) of the Right in Technical Data and Computer
Software clause at DFARS 52.227-7013, as amended.
Rand McNally, TripMaker, the Rand McNally logo and the globe design mark are registered trademarks and OverDryve is a trademark of RM Acquisition, LLC, d/b/a Rand McNally.
Portions © 2017 HERE. All rights reserved. This data includes information taken with permission from Canadian authorities,including © Her Majesty the Queen in Right of Canada, © Queen’s
Printer for Ontario. © 2017 InfoGation. All rights reserved.
© 2017 Rand McNally. All rights reserved. U.S. Patent Nos. 7,580,791 and 8,214,141.

OverDryve™ Pro User Manual

VIP Customer Support

Questions about using OverDryve™? Our team is ready to
help.
Call toll-free:

800-237-7270
E-mail:

support@randmcnally.com

OVERDRYVE_USERMANUAL_112916_v001

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Language                        : en-US
XMP Toolkit                     : Adobe XMP Core 5.6-c138 79.159824, 2016/09/14-01:09:01
Create Date                     : 2017:07:13 11:58:18-05:00
Metadata Date                   : 2017:07:13 11:58:25-05:00
Modify Date                     : 2017:07:13 11:58:25-05:00
Creator Tool                    : Adobe InDesign CC 2017 (Macintosh)
Instance ID                     : uuid:d3ce7ea8-7415-514f-8625-90378eb70205
Original Document ID            : xmp.did:5650D6F17F2068118C14E16BDEB5B80C
Document ID                     : xmp.id:6d0b2708-951a-40c4-a598-d6fda9be178d
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:c4792a17-ead8-490d-a733-4fcb1866251d
Derived From Document ID        : xmp.did:d9f0c209-8d49-7747-9716-fdaabc04355c
Derived From Original Document ID: xmp.did:5650D6F17F2068118C14E16BDEB5B80C
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Macintosh)
History Changed                 : /
History When                    : 2017:07:13 11:58:18-05:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 60
Creator                         : Adobe InDesign CC 2017 (Macintosh)

EXIF Metadata provided by EXIF.tools

Over Dryve 8 Pro User Manual 7 EN

Navigation menu

Versions of this User Manual:

Views

Navigation