Quectel BC95 AT Commands Manual V2.0
Quectel_BC95_AT_Commands_Manual_V2.0
Quectel_BC95_AT_Commands_Manual_V2.0
Quectel_BC95_AT_Commands_Manual_V2.0
Quectel_BC95_AT_Commands_Manual_V2.0
User Manual: Pdf
Open the PDF directly: View PDF
Page Count: 131 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- About the Document
- Contents
- Table Index
- 1 Introduction
- 2 Implementation Status
- 3 3GPP Commands (27.007)
- 3.1. ATI Display Product Identification Information
- 3.2. ATE Set Command Echo Mode
- 3.3. AT+CGMI Request Manufacturer Identification
- 3.4. AT+CGMM Request Manufacturer Model
- 3.5. AT+CGMR Request Manufacturer Revision
- 3.6. AT+CGSN Request Product Serial Number
- 3.7. AT+CEREG EPS Network Registration Status
- 3.8. AT+CSCON Signalling Connection Status
- 3.9. AT+CLAC List Available Commands
- 3.10. AT+CSQ Get Signal Strength Indicator
- 3.11. AT+CGPADDR Show PDP Addresses
- 3.12. AT+COPS PLMN Selection
- 3.13. AT+CGATT PS Attach or Detach
- 3.14. AT+CGACT Activate or Deactivate a PDP Context
- 3.15. AT+CIMI Request International Mobile Subscriber Identity
- 3.16. AT+CGDCONT Define a PDP Context
- 3.17. AT+CFUN Set Phone Functionality
- 3.18. AT+CMEE Report Mobile Termination Error
- 3.19. AT+CCLK Return Current Date & Time
- 3.20. AT+CPSMS Power Saving Mode Setting
- 3.21. AT+CEDRXS eDRX Setting
- 3.22. AT+CEER Extended Error Report
- 3.23. AT+CEDRXRDP eDRX Read Dynamic Parameters
- 3.24. AT+CTZR Time Zone Reporting
- 3.25. AT+CIPCA Initial PDP Context Activation
- 3.26. AT+CGAPNRC APN Rate Control
- 3.27. AT+CGAUTH Define PDP Context Authentication Parameters
- 4 ETSI Commands (27.005)
- 5 General Commands
- 5.1. AT+NRB Reboot the Module
- 5.2. AT+NUESTATS Query UE Statistics
- 5.3. AT+NEARFCN Specify Search Frequencies
- 5.4. AT+NSOCR Create a Socket
- 5.5. AT+NSOST SendTo Command (UDP Only)
- 5.6. AT+NSOSTF SendTo Command with Flags (UDP Only)
- 5.7. AT+NSORF Receive Command (UDP Only)
- 5.8. AT+NSOCL Close a Socket
- 5.9. +NSONMI Indicator of Arrived Socket Messages (Response Only)
- 5.10. AT+NPING Test IP Network Connectivity to a Remote Host
- 5.11. AT+NBAND Set Supported Bands
- 5.12. AT+NLOGLEVEL Set Debug Logging Level
- 5.13. AT+NCONFIG Configure UE Behaviour
- 5.14. AT+NATSPEED Configure UART Port Baud Rate
- 5.15. AT+NCCID Card Identification
- 5.16. AT+NFWUPD Firmware Update via UART
- 5.17. AT+NPOWERCLASS Set the Mapping for Band and Power Class
- 5.18. AT+NPSMR Power Saving Mode Status Report
- 5.19. AT+NPTWEDRXS Paging Time Window Value and eDRX Setting
- 5.20. AT+NPIN PIN Operation
- 5.21. AT+NCSEARFCN Clear Stored EARFCN
- 6 Huawei's IoT Platform Commands
- 6.1. Description of Huawei's IoT Platform Commands
- 6.1.1. AT+NCDP Configure and Query CDP Server Settings
- 6.1.2. AT+QSECSWT Set Data Encryption Mode
- 6.1.3. AT+QSETPSK Set PSK ID and PSK
- 6.1.4. AT+NMGS Send Messages
- 6.1.5. AT+NMGR Get Messages
- 6.1.6. AT+NNMI New Message Indications
- 6.1.7. AT+NSMI Sent Message Indications
- 6.1.8. AT+NQMGR Query Received Messages
- 6.1.9. AT+NQMGS Query Sent Messages
- 6.1.10. AT+NMSTATUS Message Registration Status
- 6.1.11. AT+QLWULDATAEX Send CON/NON Messages
- 6.1.12. AT+QLWULDATASTATUS Query CON Messages Sending Status
- 6.1. Description of Huawei's IoT Platform Commands
- 7 Error Values
- 8 Reset Reasons
- 9 Examples
- 10 Appendix A Reference