RAISCUBE R2 Operation Manual
User Manual: Pdf
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
RAISCUBE FDM 3D Printer RAISCUBE 3D Printer User Manual 1. X-Motion Leveling. Keep a same distance between top surface of Z-Axis Motor Fixed Plate and bottom face of Z-Axis Link Block (Left&Right). If not, turn a side of “Flexible Coupling” to keep two sides same to make it level. 2.Hotbed Level. 2.1 In the control panel, press control button and spin and press it to “Prepare” – “Z Home”, then Extruder moves torwards hotbed. Check if nozzle top almost touches hotbed surface. If not, find the long screw behind Left Z-Axis Link Block, and adjust it to be. 2.2 Panel Control, “Prepare” – “Auto Home”, to move nozzle to origin point. And still check if the distance between nozzle top and hotbed surface. It should be only allow a piece of A4 paper to pass through. If not, make clockwise (or coutercolockwise) rotation of the Wing Nuts beneath hotbed surface. Manually move hotbed or slide Extruder to other vertexes of hotbed to make it level evenly. 3. CURA 3D Slicing Software 3.1 What can CURA help us? Cura is mainly used for model slicing. It calculates paths upon the model files, and then generates 3D model codes, named “.gcode”. “STL” is the most common origin model files. These files can be save as “.stl” in a certain drawing software or download online. RAISCUBE FDM 3D Printer 3.2 Installation of Cura. Just like any other normal software installation. Find the “Cura.exe” in SD Card, and double click to cause the following window. RAISCUBE FDM 3D Printer RAISCUBE FDM 3D Printer RAISCUBE FDM 3D Printer RAISCUBE FDM 3D Printer Click “Finsh” after configure the parameters as in pix, then Cura is installed successfully and show up. RAISCUBE FDM 3D Printer 1.4 Cura 3D Printing Slicing Configuration. “Layer height” is the most important setting to determine the quality of your print. Normal quality prints are 0.2mm, high quality is 0.1 or 0.05mm. Shell Thickness: Thickness of the outside shell in the horizontal direction.This is used in combination with the nozzle size to define the number of perimeter lines and the thickness of those perimeter lines. This controls the thickness of the bottom and top layers, the amount of solid layers put down is calculated by the layer thickness and this value.Having this value a multiple of the layer thickness makes sense. And This controls how densely keep it near your wallfilled the insides ofto your printan willevenly be. thickness make For a solid part use 100%, for an strong part. Details about the retraction can be configured in the advanced tab. Open File. Save file. Est Printing Time. Speed at which printing happens. A well adjusted Ultimaker can reach 150mm/s, but for good quality prints you want to print slower. Printing speed depends on a lot of factors. So you will be experimenting with optimal settings for this. empty part use 0%. A value around 20% is usually enough. This won't affect the outside of the print and only adjusts how strong the part becomes. Type of support structure build. Touching buildplate is the most commonly used support setting.None does not do any support.Touching buildplate only creates support where the support structure will touch the build platform.Everywhere creates support even on top of parts of the model. Retract the filament when the nozzle is moving over a none-printed area. Layer View. Printing Temperature used for printing. Set at 0 to pre-heat yourself.For PLA a value of 210℃ is usually used.For ABS a Diameter – Filament Diameter (e.g 1.75mm);Flow--Flow compensation, the amount of material extruded is multiplied by this value. Nozzle Size(mm) – 0.4mm. Different options that help in preventing corners from lifting due to warping.Brim adds a single layer thick flat area around your object which is easy to cut off afterwards, and it is the recommended option. Raft adds a thick raster below the object and a thin interface between this and your object.(Note that enabling the brim or raft disables the skirt) value of 230℃ or higher is required. Bed Temperature is used for the heated printer bed. Set at 0 to pre-heat yourself. RAISCUBE FDM 3D Printer Add a certain amount of overlapping extrusion on dual-extrusion prints. This bonds the different colors together. TravelSpeed -- Speed at which travel moves are done, a well built RAISCUBE can reach speeds of 250mm/s. But some machines might miss steps then. InfillSpeed: Speed at which infill parts are printed. If set to 0 then the print speed is used for the infill. Printing the infill faster can greatly reduce printing time, but this can negatively affect print quality. Bottom Layer Speed: Print speed for the bottom layer, you want to print the first layer slower so it sticks better to the printer bed. Outer Shell Speed: Speed at which outer shell is printed. If set to 0 then the print speed is used. Printing the outer shell at a lower speed improves the final skin quality. However, having a large difference between the inner shell speed and the outer shell speed will effect quality in a negative way. Inner Shell Speed: Speed at which inner shells are printed. If set to 0 then the print speed is used. Printing the inner shell faster then the outer shell will reduce printing time. It is good to set this somewhere in between the outer shell speed and the infill/printing speed. Minmal Layer Time: Minimum time spent in a layer, gives the layer time to cool down before the next layer is put on top. If the layer will be placed down too fast the printer will slow down to make sure it has spent at least this amount of seconds printing this layer. Enable Cooling Fan – Check to turn on extruder cooling fan. RAISCUBE FDM 3D Printer “Rotate” “Scale” “Mirror” Click on the model, “Rotate” “Scale” “Mirror” 3 buttons appear on left bottom coner. RAISCUBE FDM 3D Printer Speed: Speed at which the filament is retracted, a higher retraction speed works better. But a very high retraction speed can lead to filament grinding. 120 is a common value for it. Retraction: Retract the filament when the nozzle is moving over a none-printed area. Details about the retraction can be configured in the advanced tab. Distance: Amount of retraction, set at 0 for no retraction at all. A value of 4.5mm seems to generate good results. Normally set to be 3~5mm. Cut off object bottom: Sinks the object into the platform, this can be used for objects that do not have a flat bottom and thus create a too small first layer. Also can be used to printing Model is locked by default to keep the whole object a same zoom rate, click on the lock icon to zoom XYZ separately. Scale: Middle icon is scale to adjust model size for printing. After Configuration of Parameters, remember to save files to SD Card. Pleaes note to name file in English, or will fail to printing. RAISCUBE FDM 3D Printer 4. LCD Control Panel Menu ４.１ Screen Display Explanation. Extruder Temp. Current Temp.／Target HotBed Temp. Current Temp./Target Temp. Usage of Cooling Fan. Present Nozzle position in XYZ coordinate system. Nozzle Speed Rate. Moving Speed = Setting Speed(in Cura)*Nozzle Speed Rate. This rate can be changed by LCD Control Panel. Time used in printing. Printing Progress Bar. Status，Printing… RAISCUBE FDM 3D Printer 4.2 Menu Map
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 12 Language : zh-CN Tagged PDF : Yes Author : Administrator Creator : Microsoft? Office Word 2007 Create Date : 2017:02:23 14:26:05+08:00 Modify Date : 2017:02:23 14:26:05+08:00 Producer : Microsoft? Office Word 2007EXIF Metadata provided by EXIF.tools