Stryker Brochure Plastic Coil Reelx Stt

Reelx Stt Brochure reelx_stt_brochure reelx_stt_brochure 2 2013 pdf 258413772373414384

2013-03-17

: Pdf Reelx Stt Brochure reelx_stt_brochure 3 2013 pdf

Open the PDF directly: View PDF PDF.
Page Count: 4

DownloadStryker Brochure - Plastic Coil Reelx Stt
Open PDF In BrowserView PDF
62_10_LJPRSTT_B_JP_Reelx_STT_Brochure_Layout1 5/12/10 3:49 PM Page 1

™

ReelX STT
Knotless Anchor System

62_10_LJPRSTT_B_JP_Reelx_STT_Brochure_Layout1 5/12/10 3:49 PM Page 2

ReelX STT
Knotless Anchor System
The ReelX STT 5.5mm knotless anchor
features an incremental tensioning
mechanism, which enables patient
Specific Tissue Tensioning during
arthroscopic rotator cuff repair. The
body of the ReelX STT has a diameter
of 5.5mm, and with each incremental
turn of the handle, expands up to
6.5mm. The expanding body of the
ReelX STT is designed to provide
enhanced fixation.

Quick Steps:
Load up to two #2 sutures through the
anchor using the suture threader.

While maintaining slight tension on the
suture, slide the anchor down on the bone
to the desired insertion site. Remove any
excess suture between the anchor and
tissue by gently pulling on the ends of the
suture. Mallet the anchor in until it is flush
with the cortical surface of the bone.

Simplicity was important when
designing the ReelX STT. Working
suture is loaded through the use of
a pull tab that is securely attached
to the inserter handle. The ReelX STT
also features a sharp metal tip,
making instrumentation to aid in
insertion optional.

62_10_LJPRSTT_B_JP_Reelx_STT_Brochure_Layout1 5/12/10 3:49 PM Page 3

ReelX STT
Knotless Anchor System
Features and Benefits
•

Anchor Body Expands from 5.5mm up to 6.5mm

•

Sharp Tip Makes Instrumentation Optional

•

Incremental Tensioning Allows for More Control
Over The Repair

Ordering Information
Part Number

Description

3910-600-060 ReelX STT Knotless Anchor*
3910-004-040 6.5mm Zip Drill (4.0mm x 13.5mm)
3910-003-065 6.5mm Tapered Awl
* Packaged in Boxes of 5

Release the tether suture from the
inserter handle.

While holding the yellow end of the handle,
rotate the black knob clockwise a minimum
of one revolution to spool excess suture
into the anchor. A maximum of three
complete revolutions can be made. The
implant has one locking point every 60º of
revolution of the black knob, and advances
approximately 1.5mm of suture for every
60º of rotation. Additional tension may be
applied to the suture by re-engaging the
inserter shaft.

62_10_LJPRSTT_B_JP_Reelx_STT_Brochure_Layout1 5/12/10 3:49 PM Page 4

325 Corporate Drive
Mahwah, NJ 07430
t: 201 831 5000
www.stryker.com

A surgeon must always rely on his or her own professional clinical judgment when deciding whether to use a
particular product when treating a particular patient. Stryker does not dispense medical advice and recommends
that surgeons be trained in the use of any particular product before using it in surgery.
The information presented is intended to demonstrate the breadth of Stryker product offerings. A surgeon
must always refer to the package insert, product label and/or instructions for use before using any Stryker
product. Products may not be available in all markets because product availability is subject to the regulatory
and/or medical practices in individual markets. Please contact your Stryker representative if you have questions
about the availability of Stryker products in your area.
Stryker Corporation or its divisions or other corporate affiliated entities own, use or have applied for the
following trademarks or service marks: ReelX STT and Stryker. All other trademarks are trademarks of their
respective owners or holders.
Literature Number: LJPRSTT-B
MS/GS 04/10
Copyright © 2010 Stryker
Printed in USA
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Copy, Extract
Page Count                      : 4
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:f2f8596b-953a-4490-b6a6-431af9d2b21b
Producer                        : QuarkXPress(R) 8.16
X Press Private                 : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%EndComments
Create Date                     : 2010:05:12 15:49:21-05:00
Creator Tool                    : QuarkXPress(R) 8.16
Modify Date                     : 2010:05:20 14:18:40-04:00
Metadata Date                   : 2010:05:20 14:18:40-04:00
Document ID                     : uuid:a347641c-4865-b748-a374-dc8fb19109b5
Instance ID                     : uuid:0704941c-7e49-8d46-beb0-5863c538494c
Format                          : application/pdf
Title                           : Stryker Brochure - Plastic Coil
Creator                         : QuarkXPress(R) 8.16
EXIF Metadata provided by EXIF.tools

Navigation menu