ST LINK/V2 In Circuit Debugger/programmer For STM8 And STM32 Link User Manual
User%20Manual%20-%20en.DM00026748
User Manual: Pdf
Open the PDF directly: View PDF 
.
Page Count: 19
| Download | |
| Open PDF In Browser | View PDF |
UM1075 User manual ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 Introduction The ST-LINK/V2 is an in-circuit debugger/programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces, facilitate the communication with any STM8 or STM32 microcontroller located on an application board. In addition to providing the same functionalities as the ST-LINK/V2, the ST-LINK/V2-ISOL features digital isolation between the PC and the target application board. It also withstands voltages of up to 1000 VRMS. The USB full-speed interface allows communication with a PC and: • STM8 devices via ST Visual Develop (STVD) or ST Visual Program (STVP) software (which are available from STMicroelectronics). • STM32 devices via Atollic®, IAR™, Keil®, and TASKING integrated development environments. Figure 1. ST-LINK/V2 and ST-LINK/V2-ISOL ST-LINK/V2 March 2016 ST-LINK/V2-ISOL DocID018748 Rev 7 1/19 www.st.com 1 Contents UM1075 Contents 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 Product contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 Hardware configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.1 5 Connection with STM8 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.1.1 Standard ERNI connection with SWIM flat ribbon . . . . . . . . . . . . . . . . . . 9 4.1.2 Low-cost SWIM connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.1.3 SWIM signals and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.2 Connection with STM32 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.3 ST-LINK/V2 status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Software configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.1 ST-LINK/V2 firmware upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.2 STM8 application development . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.3 STM32 application development and Flash programming . . . . . . . . . . . . 15 6 Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2/19 DocID018748 Rev 7 UM1075 List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. List of the order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SWIM flat ribbon connections for ST-LINK/V2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 SWIM low-cost cable connections for ST-LINK/V2-ISOL . . . . . . . . . . . . . . . . . . . . . . . . . . 11 JTAG/SWD cable connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 How third-party toolchains support ST-LINK/V2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 DocID018748 Rev 7 3/19 3 List of figures UM1075 List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. 4/19 ST-LINK/V2 and ST-LINK/V2-ISOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ST-LINK/V2 product contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ST-LINK/V2-ISOL product contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Connectors of the ST-LINK/V2 (on the left) and ST-LINK/V2-ISOL (on the right) . . . . . . . . 8 ERNI connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Key detail on connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Low-cost connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Target SWIM connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 JTAG and SWD connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 JTAG debugging flat ribbon layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 SWIM ST-LINK/V2 standard ERNI cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 SWIM ST-LINK/V2 low-cost cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 DocID018748 Rev 7 UM1075 1 Features Features • 5 V power supplied by a USB connector • USB 2.0 full speed compatible interface • USB standard A to Mini-B cable • SWIM specific features • 2 – 1.65 V to 5.5 V application voltage supported on SWIM interface – SWIM low-speed and high-speed modes supported – SWIM programming-speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed – SWIM cable for connection to the application via an ERNI standard vertical (ref: 284697 or 214017) or horizontal (ref: 214012) connector – SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector JTAG/serial wire debugging (SWD) specific features – 1.65 V to 3.6 V application voltage supported on the JTAG/SWD interface and 5 V tolerant inputs – JTAG cable for connection to a standard JTAG 20-pin pitch 2.54 mm connector – Supports JTAG communication – Supports serial wire debug (SWD) and serial wire viewer (SWV) communication • Direct firmware update feature supported (DFU) • Status LED which blinks during communication with the PC • 1000 VRMS high isolation voltage (ST-LINK/V2-ISOL only) • Operating temperature 0 to 50 °C Ordering information To order the ST-LINK/V2 refer to Table 1: Table 1. List of the order codes Order code ST-LINK description ST-LINK/V2 In-circuit debugger/programmer ST-LINK/V2-ISOL In-circuit debugger/programmer with digital isolation DocID018748 Rev 7 5/19 18 Product contents 3 UM1075 Product contents The cables delivered within the product are showed in Figure 2: ST-LINK/V2 product contents and Figure 3: ST-LINK/V2-ISOL product contents. They include (from left to right in Figure 2 and Figure 3): • USB standard A to Mini-B cable (A) • ST-LINK/V2 debugging and programming (B) • SWIM low-cost connector (C) • SWIM flat ribbon with a standard ERNI connector at one end (D) • JTAG or SWD and SWV flat ribbon with a 20-pin connector (E) Figure 2. ST-LINK/V2 product contents B C A 6/19 DocID018748 Rev 7 D E UM1075 Product contents Figure 3. ST-LINK/V2-ISOL product contents C A E D B DocID018748 Rev 7 7/19 18 Hardware configuration 4 UM1075 Hardware configuration The ST-LINK/V2 is designed around the STM32F103C8 device, which incorporates the high-performance ARM® Cortex®-M3 core. It is available in a TQFP48 package. As shown in Figure 4, the ST-LINK/V2 provides two connectors: • an STM32 connector for the JTAG/SWD and SWV interface • an STM8 connector for the SWIM interface The ST-LINK/V2-ISOL provides one connector for the STM8 SWIM, STM32 JTAG/SWD and SWV interfaces. Figure 4. Connectors of the ST-LINK/V2 (on the left) and ST-LINK/V2-ISOL (on the right) C A B D D 1. A = STM32 JTAG and SWD target connector 2. B = STM8 SWIM target connector 3. C = STM8 SWIM, STM32 JTAG and SWD target connector 4. D = Communication activity LED 4.1 Connection with STM8 applications For STM8 developments, the ST-LINK/V2 can be connected to the target board by two different cables, depending on the connector available on the application board. These cables are: 8/19 • SWIM flat ribbon with a standard ERNI connector at one end • SWIM cable with two 4-pin, 2.54 mm connector or SWIM separate-wires cable DocID018748 Rev 7 UM1075 4.1.1 Hardware configuration Standard ERNI connection with SWIM flat ribbon Figure 5 shows how to connect the ST-LINK/V2 if a standard ERNI 4-pin SWIM connector is present on the application board. Figure 5. ERNI connection A A B B C C 1. A = Target application board with ERNI connector 2. B = Wire cable with ERNI connector at one end 3. C = STM8 SWIM target connector 4. See Figure 11: SWIM ST-LINK/V2 standard ERNI cable. Figure 6 shows that pin 16 is missing on the ST-LINK/V2-ISOL target connector. This missing pin is used as a safety key on the cable connector, to guarantee connection of the SWIM cable in the correct position on the target connector even pins, used for both SWIM and JTAG cables. Figure 6. Key detail on connectors DocID018748 Rev 7 9/19 18 Hardware configuration 4.1.2 UM1075 Low-cost SWIM connection Figure 7 shows how to connect the ST-LINK/V2 if a 4-pin, 2.54 mm, low-cost SWIM connector is present on the application board. Figure 7. Low-cost connection A A B B C C 1. A = Target application board with 4-pin, 2.54 mm, low-cost connector 2. B = Wire cable with a 4-pin connector or separate-wires cable 3. C = STM8 SWIM target connector 4. See Figure 12: SWIM ST-LINK/V2 low-cost cable 10/19 DocID018748 Rev 7 UM1075 4.1.3 Hardware configuration SWIM signals and connections Table 2 summarizes the signal names, functions, and target connection signals using the wire cable with a 4-pin connector. Table 2. SWIM flat ribbon connections for ST-LINK/V2 Pin no. Name Function Target connection 1 VDD Target VCC(1) MCU VCC 2 DATA SWIM MCU SWIM pin 3 GND GROUND GND 4 RESET RESET MCU RESET pin 1. The power supply from the application board is connected to the ST-LINK/V2 debugging and programming board to ensure signal compatibility between both boards. Figure 8. Target SWIM connector Table 3 summarizes the signal names, functions, and target connection signals using the separate-wires cable. As the SWIM separate-wires cable has independent connectors for all pins on one side, it is possible to connect the ST-LINK/V2-ISOL to an application board without a standard SWIM connector. On this flat ribbon, all signals are referenced by a specific color and a label to ease the connection on target. Table 3. SWIM low-cost cable connections for ST-LINK/V2-ISOL Color Cable pin name Function Target connection Red TVCC Target VCC(1) MCU VCC Green UART-RX Blue UART-TX Unused Reserved (2) (not connected on the target board) Yellow BOOT0 Orange SWIM SWIM MCU SWIM pin Black GND GROUND GND White SWIM-RST RESET MCU RESET pin 1. The power supply from the application board is connected to the ST-LINK/V2 debugging and programming board to ensure signal compatibility between both boards. 2. BOOT0, UART-TX and UART-RX are reserved for future developments. DocID018748 Rev 7 11/19 18 Hardware configuration UM1075 TVCC, SWIM, GND and SWIM-RST can be connected to a low-cost 2.54 mm pitch connector or to pin headers available on the target board. 4.2 Connection with STM32 applications For STM32 developments, the ST-LINK/V2 needs to be connected to the application using the standard 20-pin JTAG flat ribbon provided. Table 4 summarizes the signals names, functions, and target connection signals of the standard 20-pin JTAG flat ribbon. Table 4. JTAG/SWD cable connections ST-LINK/V2 connector (CN3) Pin no. 1 ST-LINK/V2 function Target connection (JTAG) Target connection (SWD) VAPP Target VCC MCU VDD(1) MCU VDD(1) 3 TRST JTAG TRST JNTRST GND(2) 4 GND GND GND(3) GND(3) 5 TDI JTAG TDO JTDI GND(2) 6 GND GND GND(3) GND(3) 7 TMS_SWDIO JTAG TMS, SW IO JTMS SWDIO GND(3) 2 8 GND GND GND(3) 9 TCK_SWCLK JTAG TCK, SW CLK JTCK SWCLK GND(3) 10 GND GND GND(3) 11 NC Not connected Not connected Not connected GND(3) 12 GND GND GND(3) 13 TDO_SWO JTAG TDI, SWO JTDO TRACESWO(4) 14 GND GND GND(3) GND(3) 15 NRST NRST NRST NRST GND(3) 16 GND GND GND(3) 17 NC Not connected Not connected Not connected GND(3) 18 GND GND GND(3) 19 VDD VDD (3.3V)(5) Not connected Not connected GND GND(3) GND(3) 20 GND 1. The power supply from the application board is connected to the ST-LINK/V2 debugging and programming board to ensure signal compatibility between both boards. 2. Connect to GND for noise reduction on the ribbon. 3. At least one of this pin must be connected to the ground for correct behavior (connecting all of them is recommended). 4. Optional: for Serial Wire Viewer (SWV) trace. 5. Available on ST-LINK/V2 only and not connected on ST-LINK/V2/OPTO. 12/19 DocID018748 Rev 7 UM1075 Hardware configuration Figure 9 shows how to connect the ST-LINK/V2 to a target using the JTAG cable. Figure 9. JTAG and SWD connection A B A B C C 1. A = Target application board with JTAG connector 2. B = JTAG/SWD 20-wire flat cable 3. C= STM32 JTAG and SWD target connector The reference of the connector needed on the target application board is: 2x10C header wrapping 2x40C H3/9.5 (pitch 2.54) - HED20 SCOTT PHSD80. Figure 10. JTAG debugging flat ribbon layout 9LHZHGIURPDERYH3&% AI Note: For low cost applications or when the standard 20-pins-2.54mm-pitch-connector footprint is too big, it is possible to implement the Tag-Connect solution to save cost and space on the application board. The Tag-Connect adapter and cable provide a simple reliable means of connecting ST-LINK/V2 or ST-LINK/V2-ISOL to the PCB without requiring a mating DocID018748 Rev 7 13/19 18 Hardware configuration UM1075 component on application PCB. For more details on this solution and application-PCB-footprint information, visit www.tag-connect.com. The references of components compatible with JTAG and SWD interfaces are: 4.3 a) TC2050-ARM2010 adapter (20-pin- to 10-pin-interface board) b) TC2050-IDC or TC2050-IDC-NL (No Legs) (10-pin cable) c) TC2050-CLIP retaining clip for use with TC2050-IDC-NL (optional) ST-LINK/V2 status LEDs The LED labeled ‘COM’ on top of the ST-LINK/V2 shows the ST-LINK/V2 status (whatever the connection type). When the: 14/19 • LED is blinking RED: the first USB enumeration with the PC is taking place. • LED is RED: communication between the PC and ST-LINK/V2 is established (end of enumeration). • LED is blinking GREEN/RED: data are being exchanged between the target and the PC. • LED is GREEN: the last communication has been successful. • LED is ORANGE: ST-LINK/V2 communication with the target has failed. DocID018748 Rev 7 UM1075 Software configuration 5 Software configuration 5.1 ST-LINK/V2 firmware upgrade The ST-LINK/V2 embeds a firmware upgrade mechanism for in-situ upgrade through the USB port. As the firmware might evolve during the whole life of the ST-LINK/V2 product (new functionality, bug fixes, support for new microcontroller families …), it is recommended to visit www.st.com/stlinkv2 periodically in order to stay up-to-date with the latest firmware version. 5.2 STM8 application development Refer to ST toolset Pack24 with Patch 1 or more recent, which includes ST Visual Develop (STVD) and ST Visual Programmer (STVP). 5.3 STM32 application development and Flash programming Third-party toolchains, Atollic® TrueSTUDIO, IAR™ EWARM, Keil® MDK-ARM™, and TASKING VX-toolset support ST-LINK/V2 according to the versions given in Table 5 or in the most recent version available. Table 5. How third-party toolchains support ST-LINK/V2 Third party Atollic® IAR ™ Keil ® TASKING Toolchain Version TrueSTUDIO 2.1 EWARM 6.20 MDK-ARM ™ 4.20 VX-toolset for ARM® Cortex®-M 4.0.1 The ST-LINK/V2 requires a dedicated USB driver. If the toolset installed it automatically, the file stlink_winusb.inf is installed in/inf (where is typically C:/Windows). If the toolset setup did not install it automatically, the driver can be found on www.st.com: 1. Connect to www.st.com. 2. In the search tab, part number field, look for ST-LINK/V2. 3. Click on the Generic Part Number column hyperlink to ST-LINK/V2. 4. In the Design support tab, SW drivers section, click on the icon to download st-link_v2_usbdriver.zip. 5. Unzip and run ST-Link_V2_USBdriver.exe. For more information on third-party tools, visit the following websites: • www.atollic.com • www.iar.com • www.keil.com • www.tasking.com DocID018748 Rev 7 15/19 18 Schematics 6 UM1075 Schematics Figure 11. SWIM ST-LINK/V2 standard ERNI cable 7DUJHWERDUG KRUL]RQWDOPRXQW 67/,1.9 ERDUG 1RWH FRQQHFWRUORFDWHGRQWKH HGJHRIWKHERDUG &DEOHOHQJKWPP /RZFRVW IHPDO FRQQHFWRU (51, 3&%)RRWSULQW 67/,1.9 PDOH FRQQHFWRU 1RWH %ODFNZLUHORFDWLRQ 3,19'' 3,1'$7$ 86% 3,1*1' &1 7DUJHWERDUG YHUWLFDOPRXQW 3,15(6(7 &1 86% 3&%)RRWSULQW 3&% DL9 1. Legend for pin descriptions: VDD = Target voltage sense DATA = SWIM DATA line between target and debug tool GND = Ground voltage RESET = Target system reset 16/19 DocID018748 Rev 7 UM1075 Schematics Figure 12. SWIM ST-LINK/V2 low-cost cable 67/,1.9 E RDUG 7DUJHWERDUG $SSOLFDWLRQPDOH FRQQHFWRU /RZFRVW IHPDO FRQQHFWRU &DEOHOHQJKW PP /RZFRVW IHPDO FRQQHFWRU 67/,1.9 PDOH FRQQHFWRU 3&% 3,Q9'' 3,Q9'' 3,Q'$7$ 3,Q'$7$ 3,Q*1' 3,Q*1' 3,Q5(6(7 86% 3,Q5(6(7 &1 &1 86% 3&% 3&% DL9 1. Legend for pin descriptions: VDD = Target voltage sense DATA = SWIM DATA line between target and debug tool GND = Ground voltage RESET = Target system reset DocID018748 Rev 7 17/19 18 Revision history 7 UM1075 Revision history Table 6. Document revision history 18/19 Date Revision Changes 22-Apr-2011 1 Initial release. 03-Jun-2011 2 Table 2: SWIM flat ribbon connections for ST-LINK/V2: added footnote 1 to the function “Target VCC”. Table 4: JTAG/SWD cable connections: added footnote to the function “Target VCC”. Table 5: How third-party toolchains support ST-LINK/V2: updated the “Versions” of IAR and Keil. 19-Aug-2011 3 Added USB driver details to Section 5.3. 11-May-2012 4 Added SWD and SWV to JTAG connection features. Modified Table 4: JTAG/SWD cable connections. 13-Sep-2012 5 Added ST-LINK/V2-ISOL order code. Updated Section 4.1: STM8 application development on page 15 Added Note 5. in Table 4. Added Note “For low cost applications...” before Section 3.3: STLINK/V2 status LEDs on page 14 18-Oct-2012 6 Added Section 5.1: ST-LINK/V2 firmware upgrade on page 15. 25-Mar-2016 7 Updated Vrms value in Introduction and in Features. DocID018748 Rev 7 UM1075 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved DocID018748 Rev 7 19/19 19
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Tagged PDF : Yes Page Layout : SinglePage Page Mode : UseNone Page Count : 19 Creator : C2 v2.1.0.1 build 007 - c2_rendition_config : Techlit_Active Producer : Acrobat Distiller 9.0.0 (Windows) Title : ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 Keywords : Technical Literature, 018748, Product Development, Specification, User manual, ST-LINK/V2 Modify Date : 2016:03:30 15:07:23Z Subject : - Author : STMICROELECTRONICS Create Date : 2016:03:30 15:07:23ZEXIF Metadata provided by EXIF.tools